Vous êtes sur la page 1sur 8

15 20 00

SANITARY FIXTURES AND FITTINGS


INDEX TO ARTICLES
PART 1 - GENERAL
1.1 Contract Documents
1.2 Work Included
1.3 Related Works Specified Elsewhere
1.4 Quality Assurance
1.5 Submittals

PART 2 - PRODUCTS
2.1 Acceptable Manufacturers
2.2 Materials and Finishes
2.3 Fixtures
2.4 Delivery, Storage and Protection

PART 3 - EXECUTION
3.1 Installation

15 20 00 Sanitary Fixtures and Fittings Page 1 of 8


15 20 00
SANITARY FIXTURES AND FITTINGS
1. GENERAL
1.1 Contract Documents
All work of this Section shall comply with the requirements of the Contract Documents for
the Main Building works, with the Drawings, Schedules and with all other Contract
Documents.
1.2 Work Included
1.2.1 The supply of sanitary fixtures and fittings including water closets, urinals, wash
basins, sinks, faucets/taps, hand dryers, water coolers, soap dispensers, flush
valves and all accessories, sealants and the like to enable satisfactory installation
of the sanitary fixtures and fittings.
1.2.2 Provide all necessary data including manufacturers recommended Shop
Drawings, installation procedures and maintenance manuals.
1.2.3 Refer to Plumbing & Sanitary Installation Specification for installation of sanitary
fixtures and fittings.
1.3 Related Work Specified Elsewhere
a) Toilet Compartments : 10 21 00
b) Plumbing and Sanitary Installation : Refer to Plumbing & Sanitary
Specification
c) Joint Sealants : 07 30 00
d) Masonry : 04 10 00
e) Stone Assemblies : 04 20 00
f) Membrane and Roofing : 07 10 00
g) Tiling : 09 60 00
h) Toilet, Bath and Laundry Accessories : 10 24 00
1.4 Quality Assurance
1.4.1 All materials furnished under this Section shall be in conformance with specified
standards.
1.4.2 It shall be incumbent upon the Contractor to provide proof of acceptance for the
use of the plumbing fixtures and materials or systems.
1.4.3 All fixtures shall bear the permanent indestructible brand names of the
manufacturers and country of origin.
1.4.4 The minimum acceptable standard for materials furnished under this Section shall
be not less than the latest edition of the British Standard (BS) for the respective
materials to be furnished. In the absence of a specified BS, ASTM and U.L. shall
prevail.
1.5 Submittals
1.5.1 Refer to Section 01 01 10 on requirements on submittal procedures
1.5.2 Samples
a) Submit one (1) set of samples of each item for approval. All approved
samples of the sanitary wares and fittings are to be kept at the site for
reference and comparison with subsequent deliveries. Any sanitary
wares and fittings not complying with the approved sample will be
rejected.

15 20 00 Sanitary Fixtures and Fittings Page 2 of 8


b) Submit one (1) set of all miscellaneous items that are required for
connection with builders works.
1.5.3 Product Data & Certifications
a) Submit 1 set of technical descriptive and installation information for all
items prior to delivery.
b) At the time of submission of tender, submit original copies of relevant
brochures/pamphlets clearly marked out for easy reference and a
complete schedule of sanitary wares and fittings.
c) Certificates
Submit all certificates of approval for each item from all the relevant
authorities at the time of delivery.
Submit two copies of Works’ test certificates in respect of goods and
materials showing compliance with tests to British Standards (or any other
comparable and acceptable standards) and with any additional tests
specifically called for herein.
d) Country of origin
The Tenderer shall submit at the time of tender information on the
country of origin of all sanitary wares and fittings, and in the event of the
tender being successful, the Contractor shall submit certificates
confirming this country of origin with each delivery.
2.0 PRODUCTS
2.1 Acceptable Manufacturers
2.1.1 Acceptable manufacturers, subject to compliance with specified requirements.
a) Toto
b) Diethelm
c) Bobrick
d) Duravit
e) Villeroy and Boch
f) Dornbracht
g) Elkay
2.1.2 Specified manufacturer's catalogue references for each type of fixture/fitting listed
herewith establish minimum acceptable standards for products specified in this
Section. Other manufacturers offering equivalent and equal products shall be
subject to Architect’s review and approval.
2.1.3 The manufacturers and model numbers stated herewith are indicative only of the
level of quality and general appearance of the accessories intended to be priced.
2.2 Materials and Finishes
2.2.1 Fixtures listed herein are given to establish a minimum quality. All fixtures shall
bear the permanent indestructible brand names of the manufacturers.
2.2.2 All fixtures shall be free from imperfections, true to line, angles, curves, smooth,
watertight, and complete in every respect.

15 20 00 Sanitary Fixtures and Fittings Page 3 of 8


2.2.3 All fixtures specified to be of vitreous ware, shall be fired vitreous chinaware of the
best quality, non absorbent and burned so that the whole mass is thoroughly fused
and vitrified, producing a material white in colour, which when fractured will show
a homogeneous mass, close grained and free from pores. The glazing and
vitreous china fixtures shall be white, thoroughly fused and united to the body,
without discolouration, chips or flaws, and shall be free from craze. Warped or
otherwise imperfect fixtures will not be accepted.
2.2.4 All fittings, cast brass set screw escutcheons, faucets, taps, traps, exposed piping,
and the like, shall be brass, chrome plated over nickel plate with polished finish.
Any hanger nuts visible shall likewise be chrome plated over nickel plate.
2.2.5 Chrome plated or stainless steel pipes shall be used for supplies and drains
exposed to view adjacent to all fixtures and where designated elsewhere.
2.2.6 All brackets, supports, hangers and the like used shall be hot dipped galvanised
steel.
2.3 Fixtures
2.3.1 Water Closet
a) WC-1 – 590 x 360mm wall hung syphonic washdown WC bowl in vitreous
china each complete with
i) ABS plastic heavy duty seat and cover
ii) Rubber inlet spud onto WC bowl
iii) Galvanised steel bolts with hexagon nuts (2 sets)
iv) Wall flange with gasket
v) "L" chair brackets with expansion bolts
vi) Rubber bush
b) WC-2 – 410 wide x 575 deep x 315mm high wall hung syphonic
washdown WC bowl in vitreous china complete with
i) #006581.00 cover and seat
ii) Rubber inlet spud onto WC bowl
iii) Galvanised steel bolts with hexagon nuts (2 sets)
iv) Wall flange with gasket
vii) "L" chair brackets with expansion bolts
viii) Rubber bush
2.3.2 Wash Basin
a) WB-1 – 500 x 550mm semi-recessed counter type oval basin in vitreous
china with back overflow, each complete with
i) Angle brackets suitable for fixing
ii) Chrome plated brass bottle trap 32mm
iii) Chrome plated brass pop-up waste outlet 32mm
b) WB-2 - 530 x 300mm semi-circular wall hung wash basin with concealed
hangers in vitreous china with back skirting each complete with
i) Chrome plated brass bottle trap 32mm
ii) Chrome plated brass pop-up waste outlet 32mm
c) WB-3 - 570 x 400mm under counter type oval basin in vitreous china with
back overflow each complete with

15 20 00 Sanitary Fixtures and Fittings Page 4 of 8


i) Angle brackets suitable for fixing
ii) Chrome plated brass bottle trap 32mm
iii) Chrome plated brass waste outlet 32mm
iii) Chrome plated type 32mm plug and chain waste

2.3.3 Urinal
a) UR-1 - Wall mounted urinal, size 390 wide x 420 deep x 1025mm high in
vitreous china with built-in trap and back inlet in vitreous china each
complete with
i) Concealed back inlet spud with rubber bush
ii) Concealed wall hangers with expansion bolts
iii) Wall flange with gasket for discharge
iv) Outlet connector
v) Vitreous china outlet strainer
vi) Battery operated built-in sensor flush system
c) UR-2 - Wall mounted urinal, overall size 365 wide x 335 deep x 710mm
high in vitreous china with built-in trap and back inlet in vitreous
china each complete with
i) Concealed back inlet spud with rubber bush
ii) Concealed wall hangers with expansion bolts
iv) Wall flange with gasket for discharge
vii) Outlet connector
viii) Vitreous china outlet strainer
2.3.4 Flush Valve
a) Flush Valve
i) Wall Hung WC - (AS-1)
Sensor, AC operated chrome plated concealed-duct type WC
automatic flush valve with built-in stop valve cum check and
vacuum breaker valve for 4.5 litres flushing complete with cam
lock, chrome plated flush mounted photo-electric sensor eye with
protection fuse (1A), dual flush systems, push button signal
device sensor, 1100 x 400 x 32mm diameter L-shaped flush pipe
with joint, and all necessary flush and supply pipes.
ii) Wall hung Urinal – (AS-2)

Sensor, AC operated chrome plated concealed-duct type urinal


automatic flush valve with protection fuse, built-in integrated
stop valve cum check and vacuum breaker valve for 2.5 litres
flushing complete with cam lock, chrome plated flush mounted
photo-electric sensor eye with protection fuse (1A), dual flush
systems, push button signal device sensor, 1100 x 400 x 32mm
diameter L-shaped flush pipe with joint, and all necessary flush
and supply pipes.
2.3.5 Sink
a) SS-1 – Vitreous china service sink 560 x 456mm x 530mm deep (with S
trap) each complete with

15 20 00 Sanitary Fixtures and Fittings Page 5 of 8


i) Chrome-plated bottle trap
ii) 50mm diameter drain with plug and chain
iii) 40mm diameter chrome plated waste pipe
iv) Concealed hangers and supports
v) Rim cover
b) SK-1 - Stainless steel sink with double bowl and single drainer, overall
size 600 wide x 1500mm long, each complete with
i) Chrome-plated bottle trap
ii) 50mm diameter drain with plug and chain
iii) 40mm diameter chrome plated waste pipe
iv) Concealed hangers and supports
2.3.6 Faucet/Tap

The following shall be chrome plated


a) Auto Sensor Wash Basin Tap (SCT-1)
Counter top mounted battery operated auto sensor faucet with curved
spout complete with back-up battery and power generator unit, attaching
nut, washer, connecting nut, joint and sensor device built into the tap.
b) Wall Mounted Wash Basin Mixer (WBT-1)
Wall mounted wash basin mixer with projection, faucet with curved spout
complete attaching nut, washer, connecting nut, joint and wall plate.

c) Handicapped Tap (SLT-1)


Swivel type faucet with attaching nut, washer and connecting nut and
joint.
d) Bib Tap BT-1 (under Vanity Counters).
Wall mounted bib tap with hose connection complete with ditto.
e) Bib Tap with hose and Bidet Spray (BS-1)
Wall mounted bib tap and bracket with flexible hose and bidet spray
mounted on bracket with attaching nut, washer and connecting nut and
joint.
f) Pantry / Service Sink Mixer (PM-1)
Single lever centreset mixer faucet with attaching nut, washer and
connecting nut and joint.
2.4 Toilet Accessories
2.4.1 HD-1 Surface Mounted Hand Dryer: Bobrick Eclipse B-748 or approved
equivalent.

15 20 00 Sanitary Fixtures and Fittings Page 6 of 8


Surface-mounted hand dryer, overall size 390mm wide x 225mm high x 190mm
deep, shall have one piece, deep-drawn 1.6mm thick steel cover with bright
polished chrome-plated finish. The motor shall be 1/10 hp, universal type 6200rpm
with sealed ball bearing at drive shaft end and self-lubricating sleeve bearing at
non-drive end; equipped with automatic thermal-overload switch. Heating element
shall be located on inlet side of fan, shall heat without hot spots, be inaccessible
to vandals and protected by a thermal fuse. Electronic sensor shall automatically
turn dryer on when hands are held under air-outlet opening and across path of
sensor. Dryer will turn off automatically when hands are removed. Sensor shall
automatically shut dryer off approximately 1 ½ minutes after dryer turns on if an
inanimate object is placed across air-outlet opening. After inanimate object is
removed, electronic sensor shall automatically reset itself and dryer shall operate
normally.
Unit shall be protected by a limited 10-year warranty on all parts except motor
brushes. Motor brushes shall be warranted for three (3) years from date of
completion of project. Manufacturer’s service and parts manual shall be provided
to the owner upon completion of project.
2.4.2 ASD-1 Lavatory Mounted Automated Soap Dispenser: Toto TES 121 or approved
equivalent.
Sensor automated liquid soap dispenser complete with spout with bright polished
finish which shall lock to body with concealed locking mechanism that is opened
with special key provided and under counter mounted shatter-resistant
polyethylene container. Supply-tube assembly shall be removable from bottom
for filling and maintenance.
2.4.3 DF-1 Wall Mounted Drinking Fountain with Surface Mounting Plate: Elkay or
approved equivalent
Fully exposed fountain #18 gauge, type 304 stainless steel polished to a lustrous
satin finish with high shine outer edge. Stainless steel support arm incorporates
unique recess to be integrated with basin. Fountain shall have contoured basin
that minimizes splashing, safety bubblers in chrome-lated brass, which are keyed
in location to prevent rotation. Fully functional, stainless steel, vandal –resistant
front push bar, valve and in-line flow regulator to provide constant stream from 20
to 105 psi; including vandal-resistant bottom cover plates and surface mounting
plate and all fixings, fittings and accessories.
Size of basin shall be 356mm diameter
2. 5 Delivery, Storage and Protection
2.5.1 Provide all necessary protection to all items to be supplied to enable the proper
handling and storage on Site.
2.5.2 All materials and goods shall be delivered to the Site in a new condition, properly
packed and protected against damage due to handling, adverse weather or other
circumstances and, as far as practicable, they shall be kept in the packing cases
or under protective coverings until required for use. Cost of uncrating for
inspection and repacking on delivery to Site is to be borne by the Contractor.
2.5.3 Any items suffering damage in transit or on the Site prior to installation shall be
rejected and replaced by the Contractor at his own cost and expenses.
2.5.4 In the case of materials which originate outside Kingdom of Bahrain
- All materials shall be packed adequately and securely for safe
transportation with due regard to the climatic conditions encountered in
transit and on arrival.

15 20 00 Sanitary Fixtures and Fittings Page 7 of 8


- British Standard and supplements, or other comparable and acceptable
codes, shall be used as a guide for standard of packing and package
required

3.0 EXECUTION
3.1 Installation
Refer to Plumbing and Sanitary Specification for installation specification.

- END -

15 20 00 Sanitary Fixtures and Fittings Page 8 of 8

Vous aimerez peut-être aussi