Académique Documents
Professionnel Documents
Culture Documents
Issue 2
Page 1 of 7
May 2012
IPS
Individual Product Specification
Copyright reserved
Ref. no. IPS04-04-002-01
IPS04-04-002-01 Page 2
Issue 2
Contents
1 Scope
2 Normative references
4 Cross-references
5 Material application
6 Qualification
7 Release
8 Specific agreements
1 Scope
This Individual Product Specification identifies a material from a manufacturer that has been successfully qualified
to the relevant Material Specification
The Individual Product Specification specifies individual requirements, which describe the specific performance of
the material, as demonstrated by the qualification, and which have to be considered for procurement and use,
together with the Material Specification.
2 Normative references
This Airbus specification incorporates by dated or undated reference provisions from other publications. All
normative references cited at the appropriate places in the text are listed hereafter. For dated references,
subsequent amendments to or revisions of any these publications apply to this Airbus specification only when
incorporated in it by amendment of revision. For undated references, the latest issue of the publication referred to
shall be applied.
3.2 Manufacturer
The product is manufactured by: Akzo Nobel Aerospace Coatings
4 Cross-references
TN A.007.10012
5 Material application
The product shall be used in conjunction with the relevant design documents.
IPS04-04-002-01 Page 4
Issue 2
6 Qualification
6.1 Status
7 Release
Release testing shall be performed in accordance with the relevant specifications of clause 6.1.1 and specific
agreements of clause 8 (if applicable).
8 Specific agreements
Requirements of individual componenets are given in table 1. Required physical properties of the liquid paint before
the application are given in table 2.
Characteristic properties of the dry coat deviating significantly from the requirements given in AIMS 04-04-002 are
given in table 3.
IPS04-04-002-01 Page 5
Issue 2
Table 1: Physical properties of the individual componenets of coating Aerodur Barrier Primer 37045
Clause Property Unit Results Aerodur Barrier Primer 37045
Base Hardener Thinner
1.1 Volatile and non-
volatile matter % vol 52,7 – 58,7 32 – 34 N.A.
content
1.2 Finess of grind µm <32 N.A. N.A.
1.3 Density g/cm3 1,28 – 1,36 0,94 – 0,98 0,84 – 0,86
1.4 Pigment content % 37 – 40 N.A. N.A.
1.5 Isocyanate
% N.A. 7,1 – 7,4 N.A.
content
1.6 Refractive index % N.A. 1,4325 – 1,4365 1,3865 – 1,3905
1.7 Water content % <0,01 <0,05 <0,01
1.8 Gas
N.A. (1) (1) (1)
chromatogram
1.9 IR diagram N.A. (1) (1) (1)
1.10 Acid index mgKOH/g 0,60-0,63 N.A. N.A.
1.11 Amine index mgKOH/g N.A. N.A. N.A.
1.12 Hydroxyl index mgKOH/g 15-45 N.A. N.A.
1.13 Epoxy index Mmol/g 0,02-0,03 N.A. N.A.
1.14 Flash point °C 15°C 27°C 1.5°C
1.15 Viscosity 24 – 30 (ISO cup 18 – 22 (ISO cup
s Thixotropic
3) 3)
In particular, for preparations and for the first delivery, the manufacturer shall provide a safety data sheet
appropriate to the country of purchase/use.
For articles, the manufacturer shall provide information according to REACh Article 33, and additionally, safety data
sheet shall be provided whenever available.
Site competent environment health and safety authority shall be the final recipient of the documents.
At least, document has to be delivered simultaneously with the product.
Material shall comply with A1091.
!NEW! The supplier should provide chemical composition of the cured product and propose recycling possibilities
(cured/uncured product) whenever relevant.
IPS04-04-002-01 Page 7
Issue 2
RECORD OF REVISIONS
Clause
Issue Description of modification
modified
1 New standard
09/99