Académique Documents
Professionnel Documents
Culture Documents
Reference Design
Rev. A
Date: 2016-05-30
www.quectel.com
GSM/GPRS/GNSS Module Series
MC60 Reference Design
Our aim is to provide customers with timely and comprehensive service. For any
assistance, please contact our company headquarters:
te l
For technical support, or to report documentation errors, please visit:
http://www.quectel.com/support/techsupport.aspx
Or email to: Support@quectel.com
GENERAL NOTES
e c r y
u a
QUECTEL OFFERS THE INFORMATION AS A SERVICE TO ITS CUSTOMERS. THE INFORMATION
PROVIDED IS BASED UPON CUSTOMERS’ REQUIREMENTS. QUECTEL MAKES EVERY EFFORT
Q min
TO ENSURE THE QUALITY OF THE INFORMATION IT MAKES AVAILABLE. QUECTEL DOES NOT
MAKE ANY WARRANTY AS TO THE INFORMATION CONTAINED HEREIN, AND DOES NOT ACCEPT
ANY LIABILITY FOR ANY INJURY, LOSS OR DAMAGE OF ANY KIND INCURRED BY USE OF OR
RELIANCE UPON THE INFORMATION. THE INFORMATION SUPPLIED HEREIN IS SUBJECT TO
i
CHANGE WITHOUT PRIOR NOTICE.
COPYRIGHT
r e l
THE INFORMATION CONTAINED HERE IS PROPRIETARY TECHNICAL INFORMATION OF
P
QUECTEL CO., LTD. TRANSMITTING, REPRODUCTION, DISSEMINATION AND EDITING OF THIS
DOCUMENT AS WELL AS UTILIZATION OF THE CONTENT ARE FORBIDDEN WITHOUT
PERMISSION. OFFENDERS WILL BE HELD LIABLE FOR PAYMENT OF DAMAGES. ALL RIGHTS
ARE RESERVED IN THE EVENT OF A PATENT GRANT OR REGISTRATION OF A UTILITY MODEL
OR DESIGN.
Copyright © Quectel Wireless Solutions Co., Ltd. 2016. All rights reserved.
l
History
te
Revision Date Author Description
c
A 2016-05-30 Tiger CHENG Initial
u e a r y
Q min
e l i
P r
Contents
1 Introduction .......................................................................................................................................... 4
1.1. Introduction ................................................................................................................................ 4
1.2. Schematics ................................................................................................................................ 4
te l
e c r y
u
Q min a
e l i
P r
1 Introduction
1.1. Introduction
l
This document is a reference design for MC60 module. The schematics included in this document are
te
preliminary and are subject to change without prior notice.
c y
1.2. Schematics
u e a r
Q min
e l i
P r
Module Design
l
Charge golden capacitor or battery when VBAT is applied.
te
D Close to the VBAT pins D
Capacitance of C102 should VBAT
C101
the burst transmission C102 C103 C104 C105 C106
+
c +
NM_Golden capacitor
does not exceed 400mV. D101
e r y
As only powering the VRTC pin to keep the RTC will lead
an error for about 5 minutes a day, it is recommended 1. VBAT ranges from 3.3V to 4.6V.
to power VBAT and VRTC pin at the same time when 2. Module drains the maximum current around 1.6A in burst time (577us).
RTC function is needed.
u a
3. The width of VBAT trace is recommeded to be more than 2mm.
C
[1]
[3]
[3]
[5]
4. Capacitance is arranged in ascending order, with the smallest one closing to the VBAT pins,
C
LOUDSPKP
LOUDSPKN
NETLIGHT
AntennaType Active Antenna Power Supply Circuit and all capacitance as close to the VBAT pins as possible.
VRTC
VBAT
VDD_EXT
Q min
Active Need
Passive No need J101 For RF layout, please refer to
54
53
52
51
50
49
48
47
46
45
44
43
RF_ANT
U101-A RF_Layout_Application_Note.
LOUDSPKP
LOUDSPKN
VRTC
VBAT
VBAT
GND
GND
NETLIGHT
RESERVED
GND
GND
VDD_EXT
i
12 31
[4] SIM2_RST SIM2_RST GND
13 30
[4] SIM2_VDD SIM2_VDD DBG_RXD DBG_RXD [6] U101-B
L1 14 29
R109 R103 GND DBG_TXD DBG_TXD [6]
[1,2,6] 15 28 55 68
VCC_3V3 GNSS_ANT GNSS_VCC_EN GNSS_VCC_EN [2] RESERVED RESERVED
56 67
l
47nH 10R RESERVED RESERVED
0R
SIM1_DATA
RESERVED
GNSS_RXD
GNSS_VCC
57 66
GNSS_TXD
SIM1_VDD
RESERVED RESERVED
SIM1_RST
SIM1_CLK
RXD_AUX
TXD_AUX
SIM_GND
C111 C112 58 65
RESERVED RESERVED
59 64
PCM_CLK RESERVED
GND
NM NM 60 63
PCM_OUT RESERVED
61 62
PCM_SYNC PCM_IN
MC60
B B
16
17
18
19
20
21
22
23
24
25
26
27
MC60
e
VCC_3V3
r
SIM1_VDD
SIM1_RST
SIM1_CLK
SIM_GND
VOLTAGE_INPUT
NOTE
[4]
[4]
[4]
[4]
[4]
R104
[1] RXD_AUX
[1] TXD_AUX
ADC [1]
P
C115 R107 0R
R106 [1] GNSS_TXD [1]
RXD_AUX
100nF
R108 0R
[1] TXD_AUX GNSS_RXD [1]
6 5 4 3 2 1
6 5 4 3 2 1
l
Power Supply
te
D D
NOTE
The voltage converter should provide a minimum current of 2.0A.
e c r y
LDO Application
u
It is used when the DC input voltage is below 7V.
a
C
C U201 MIC29302/SPX29302
VBAT
U202
VCC_3V3
DC input
Q min
2 4 1 5
+5V IN OUT VIN VOUT
2
GND
R202
+
R201 4 R205
C201 FB
1
5
3
C202
EN
3
ADJ
GND
l i
B B
DC-DC Application
r e
1. It can be used when the input voltage is above 7V in vehicle application.
2. Use DCDC to convert high input voltage to 5V and LDO will generate
4V & 3.3V typical voltage for the module.
P
eg. DC12V IN DC 5V OUT DC 4V OUT FOR DC 3.3V OUT FOR
DCDC LDO LDO
GSM PART GNSS PART
6 5 4 3 2 1
6 5 4 3 2 1
Audio Design
l
Hands-free Application of AIN/AOUT2
te
D D
[1,3] MICP J301
NOTES C301
10pF
C302
33pF
+
ESD9B5.0ST5G
ESD9B5.0ST5G
c
1. AGND is reommended to be routed separately. C303
C304 C305 C306
33pF
D301
D302
10pF 10pF 33pF
y
2.10p&33p capacitors are used for filtering TDD noise.
Note 6
3. AIN has bias voltage of microphone. Close to MIC
e r
4. AOUT1 is capable of driving 32ohm load.
5. AOUT2 is capable of driving 8ohm load and Earphone.
u
6. These components are used to enhance the ESD performance of MIC lines,
a
C
ESD9B5.0ST5G
and thus it is strongly recommended to reserve them. 10pF
33pF
C
D303
C307 C308
R301
Q min
FB301
[1,3] LOUDSPKP
FBMH1608HM601-T 0R 1
10pF 33pF
2
C309 C310
FB302 R302 J302
[1] LOUDSPKN
FBMH1608HM601-T 0R
ESD9B5.0ST5G
10pF
D304
33pF
C311 C312
Close to Speaker
Handsets Application of AIN/AOUT1
l i
Earphone Application of AIN/AOUT2
Note 2 Note 6
B B
[1,3] MICN
Note 1
[1,3] MICP
e
ESD9B5.0ST5G
ESD9B5.0ST5G
J303 4.7uF
Close to Socket
r
4
[1,3] MICP
1 J304
[1,3] MICN C320 AGND
R303
3 3
[1] SPKP [1,3] LOUDSPKP
2 0R 4
22uF
C323 C324 2
ESD9B5.0ST5G
C321 HANDSETCON 1
C322
D307
ESD9B5.0ST5G
ESD9B5.0ST5G
C326
P
10pF 33pF
ESD9B5.0ST5G
D309
AGND
Close to Socket
Close to Socket
Close to handset connector
6 5 4 3 2 1
6 5 4 3 2 1
SIM Card
te l
D D
SIM Card Interface
c
SIM1_VDD SIM2_VDD
Note1 Note1
y
Note3 Note3
C401 C402
100nF NM 100nF
NM
e r
R401 R402
[1,4] 6 1 6 1
SIM1_VDD VCC GND [1,4] SIM2_VDD VCC GND
R403 22R R404 22R
[1] 5 2 [1] 5 2
SIM1_RST RST VPP SIM2_RST RST VPP
[1] 4 3 [1] 4 3
SIM1_CLK CLK I/O SIM2_CLK CLK I/O
u
R406 22R
a
R405 22R
Note2 Note2
Q min
6
6
1
5
3
3
C403 C404 C405 C406 C407 C408 C409 C410
U401 U402
2
2
NUP5150MUTBG NUP5150MUTBG
l i
B NOTES B
e
1. The value of C401 and C402 should be less than 1uF.
2. U401 and U402 is used for protecting SIM card against ESD, and the junction capacitance should be less than 50pF.
r
It should be placed nearby SIM card holder.
3. For MC60 module, ground of SIM card is recommended to be routed to the Pin 16("SIM_GND") of the module separately.
6 P 5 4 3 2
DRAWN BY
Tiger CHENG
CHECKED BY
Quectel Wireless Solutions
SHEET
PROJECT
MC60
SIZE
A2
4 OF 6 DATE
1
TITLE
Reference Design
VER
A
2016/5/30
A
6 5 4 3 2 1
Driver
te l
D D
Turn on/off
c
PWRKEY [1,6]
y
[5] PWRKEY_CONTROL Q501
DTC143ZETL
u e a r
Recommended circuit for turning on/off the module.
C
C
Q min
LED Indication MCU GPIO
VBAT
D501
i
MCU
l
R501
1K
1
GPIO PWRKEY_CONTROL [5]
B GPIO
2
3
POWER_ON/OFF [2]
B
GPIO
e
Q503
[1] NETLIGHT
DTC143ZETL
r
Pin "NETLIGHT" indicates the network status.
6 P
5 4 3 2
Quectel Wireless Solutions
DRAWN BY
Tiger CHENG
CHECKED BY
SHEET
PROJECT
MC60
SIZE
A2
5 OF 6 DATE
1
TITLE
Reference Design
VER
A
2016/5/30
A
6 5 4 3 2 1
Serial Interface
l
Connection of Three-line UART Port for 3.3V System
te
D Electric characteristics of the module's input and output port: D
VOHmin=0.85*VDD_EXT MCU/ARM MC60
VOLmax=0.15*VDD_EXT R601 1K
VILmax=0.25*VDD_EXT TXD
1
2
R602 1K
RXD [1,6]
c
GND
VIHmax=VDD_EXT+0.2V
R603
y
VDD_EXT=2.8V (typical value) 5K6
e r
Connection of All Functional UART Port for 3.3V System Please pay attention to the level match of UART in product application.
MC60
u a
MCU/ARM R604 1K
1
TXD RXD [1,6]
RXD
2
R605
R606
1K
1K
TXD [1,6] C
C RTS
3
4
R607 1K
RTS [1]
Q min
R609 1K
6
EINT RI [1]
R610 1K
7
GPIO DCD [1]
8
GND
It is recommended to reserve the points for upgrading the firmware.
R611 R612 R613
5K6 5K6 5K6
MC60
1 TXD [1,6]
T601
1 [1,6]
T602 RXD
NOTES T603
1
1
VBAT
T604 VCC_3V3
1. CTS&RTS will be used for HW flow control when mass data has been sent. T605
1
PWRKEY [1,5]
i
1
T606
l
control the module to enter into or exit from the sleep mode through the pin DTR.
When DTR is set to high level, and there is no on-air or hardware interrupt, Please pay attention to the level match of UART in product application.
B such as GPIO interrupt or data on serial port, the module will enter into sleep B
mode automatically.
e
3. RI will output an indication signal when activity such as voice call or SMS
r
is coming.
4. DCD is mainly applied in modem communication (PPP). The active status
represents the communication link has been set up.
5. Please pay attention to the level match of UART in product application.
P
MC60
A
1
[1] DBG_RXD T607
A [1] DBG_TXD
1
T608 Quectel Wireless Solutions
DRAWN BY PROJECT TITLE
Tiger CHENG MC60 Reference Design
It is recommended to reserve the points for debug port. SIZE VER
CHECKED BY A2 A
SHEET 6 OF 6 DATE 2016/5/30
6 5 4 3 2 1