Académique Documents
Professionnel Documents
Culture Documents
Boomer E3 C
Equipped with COP 3038 rock drills
www.atlascopco.com
E3
Standard features
»»Rock drill »»Control system
• High-frequency COP 3038 rock drills with dual-damping • Advanced Rig Control System (RCS) allowing several levels
system for optimal consumable life of automation to suit customer requirements
• Pressurized housing and mating surfaces to reduce internal • Standard functions include soft collaring and the anti-jam-
contamination of the rock drill ming function Rotation Pressure Controlled Feed (RPCF)
• Integrated diagnostic and event logging system to assist in
»»Hydraulic boom equipment maintenance
• Interactive operator panel with full-colour display
• BUT 45 heavy-duty booms for direct, fast and accurate posi-
tioning between holes
• Double rotation unit for ±190 degrees feed roll-over and ±135 »»Carrier
degrees feed rotation • Sturdy carrier with all-wheel drive
• Powered by a 6-cylinder, EPA III/COM III (Tier 3/Stage IIIA)
»»Hydraulic feed approved diesel engine
• Four jacks for stable set-up
• BMH 6900-series heavy-duty aluminium feed with high
bending and torsional resistance for maximum durability
• Snap-on stainless steel sleeves and polymer contacts »»General
• FOPS-approved cabin
• Hydraulically driven water booster pump
• Hydraulically driven compressor
• Cable reel
• Working lights
Boomer E3 C with COP 3038
Specifications
ROCK DRILL »»Electrical system
COP 3038
Shank adapter TC45
• Total installed power....................................................297 kW
• Main motors, Sf 1.3...................................................3x95 kW
Height over drill centre 84 mm
• Voltage.................................................................690–1 000 V
Length without shank 970 mm • Frequency. ................................................................50–60 Hz
Impact power 30 kW • Starting method............... star/delta (1 000 V direct start only)
Impact rate 102 Hz • Electronic overload protection for electric motors
Hydraulic pressure 200 bar • Percussion hour meter on operator display
Rotation system Separate rotation • Phase sequence indicator
Rotation speed 0–380 rpm • Earth fault indicator
• Battery charger
Rotation torque, max 190 Nm
• Power supply. ............................................................ 24 V DC
Lub. air consump. at 4 bar 5 l/s
• Transformer. .................................................................12 kVA
Flushing water 20–30 bar • Cable reel, diameter................................................. 1 800 mm
Water consumption, max 130–190 l/min* • Dual controls for cable reel
Weight 165 kg
Sound level <106 dB(A)
*Depending on drill steel
»»Hydraulic system
• Hydraulic pumps...............3 separate units, one for each boom
FEED • Pumps unloaded at start
BMH 6900 BMH 6914 BMH 6916 BMH 6918 BMH 6920 BMH 6921 • System pressure, max. ...................................................250 bar
• Hydraulic oil tank, volume max/min......................... 755/470 l
• Low oil level indicator
Total length 5 988 mm 6 598 mm 7 208 mm 7 778 mm 8 078 mm
• Oil temperature gauge on oil tank
Drill steel length 4 310 mm 4 920 mm 5 530 mm 6 100 mm 6 400 mm
• Electrical oil filling pump
Hole depth 4 043 mm 4 668 mm 5 268 mm 5 843 mm 6 140 mm
• Oil filter indicator
Weight, incl. drill 666 kg 700 kg 731 kg 756 kg 785 kg
• Water cooled oil
Feed force 22.0 kN 22.0 kN 22.0 kN 22.0 kN 22.0 kN
• Filtration. ........................................................................ 16 µm
• Mineral hydraulic oil
»»Boom
• Boom........................................................................ BUT 45 L »»Carrier
• Feed extension......................................................... 1 800 mm
• Deutz 6-cylinder, TCD 2013 L06, 2V EPA III/COM III (Tier
• Boom extension....................................................... 2 500 mm
3/Stage IIIA) approved 4-stroke water-cooled diesel engine
• Parallel holding..........................................................complete
• Power rating at 2 300 rpm. ........................... 173 kW (235 hp)
• Feed roll-over..................................................................±190°
• Torque at 1 500 rpm.....................................................907 Nm
• Feed cross-cut.................................................................±135°
• All-wheel drive
• Max. lifting angle...................................................... +55º/-42°
• Hydrostatic power steering system
• Max. swinging angle.........................................................±42°
• Hydrodynamic transmission................................. Dana 32000
• Weight, boom only......................................................3 200 kg
• Front axle...........................................................Dana 37R 116
• Rear axle .........................................Dana 276, ±8° oscillation
»»Air system • Manual differential lock on front axle, Hydralock
• Tyres. ......................................................................14.00xR24
• Hydraulically driven screw compressor. .. Atlas Copco GAR 5 • Clearance outside axles....................................................... 15º
• Capacity, max at 9 bar. .....................................................26 l/s • Hydraulic jacks, front . ........................................ 2 extendable
• Adjustable speed • Hydraulic jacks, rear...............................................................2
• Air pressure gauge • Service brakes..............................................2 separate circuits
• Hole blowing kit with 80 l air receiver • Emergency and parking brakes......................................SAHR
• Fuel tank, volume. ........................................................... 150 l
• Silencer
»»Water system • Electric system..................................................................24 V
• Batteries....................................................................2x125 Ah
• Hydraulic water booster pump................ Johnson MCVS 16-7 • Tramming lights........................................................... 8x70 W
• Water booster pump max capacity at 30 bar.............. 400 l/min • Working lights...........................................2x1 500 + 2x500 W
• Min water inlet pressure at 400 l/min, ..............................2 bar • Illuminated stairs for platform..................................... 2x70 W
• Water pressure gauge • Fire extinguisher
• Water flow guard • Spirit level....................one for longitudinal, one for sideways
• Pressure compensated water pump • Gradeability at max. load on drive wheels. ........................ 1:4
• Horn, beacon and reverse alarm
»»Control system
»»Cabin
• Rig Control System (RCS) – versatile and upgradeable to a
higher degree of automation • FOPS-approved cabin, noise level <80 dB(A) including fixed
• One adjustable, electronic control panel with colour display seat and air conditioning unit with heating function
• Transfer of data and backup settings • Hydraulic cabin lift system, 0–1 100 mm
• Integrated diagnostic system
• Separate battery for electronic system
Boomer E3 C with COP 3038
mm R46 64
Optional equipment
»»Rock drill/Drilling system »»Water system
• Hole blowing kit excluding air receiver • Water hose reel
Measurements 7780
side view
1100
brochure may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer Center for specific information.
© Copyright 2008, Atlas Copco Rock Drills AB, Örebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations and photos in this
3664
www.atlascopco.com
E3
438
3951 4200
Tramming length 17495 (BMH 6920)
Illustration shows rig with optional equipment mounted.
Coverage area
2250
10300
9950
2881
2381
245
14450
15250
Parallel coverage BUT 45 L
WEIGHT
10/2008