Académique Documents
Professionnel Documents
Culture Documents
140-200403
SERVICE MANUAL
COLOR TELEVISION/
DVD VIDEO PLAYER
MD13P3
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE-
FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE,
CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.
VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT
STARE INTO BEAM.
PREPARATION OF SERVICING
The laser diode used for a pickup head may be destroyed with external static electricity.
Moreover, even if it is operating normally after repair, when static electricity discharge is received at the
time of repair, a life of product may become short.
Please perform the following measure against static electricity, be careful of destruction of a laser diode
enough at the time of repair, and work.
• It works on the desk which performed measures against static electricity, such as conductive mat.
• Soldering iron with ground wire or ceramic type is used.
• A worker needs to use a ground conductive wrist strap for body.
A1-1
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
2. AVOID AN ELECTRIC SHOCK
make sure not modify the circuit.
There is a high voltage part inside. Avoid an Repairing except indicates causes rising of high
electric shock while the electric current is voltage, and it emits an X-ray from the cathode-
flowing. ray tube.
3. USE THE DESIGNATED PARTS 7. PERFORM A SAFETY CHECK AFTER
The parts in this equipment have the specific SERVICING
characters of incombustibility and withstand
Confirm that the screws, parts and wiring which
voltage for safety. Therefore, the part which is
were removed in order to service are put in the
replaced should be used the part which has
original positions, or whether there are the
the same character.
portions which are deteriorated around the
Especially as to the important parts for safety
serviced places serviced or not. Check the
which is indicated in the circuit diagram or the
insulation between the antenna terminal or
table of parts as a mark, the designated
external metal and the AC cord plug blades.
parts must be used.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE (INSULATION CHECK PROCEDURE)
ORIGINAL POSITION AFTER
1. Unplug the plug from the AC outlet.
ASSEMBLING OR WIRING 2. Remove the antenna terminal on TV and turn
There are parts which use the insulation on the TV.
material such as a tube or tape for safety, or 3. Insulation resistance between the cord plug
which are assembled in the condition that terminals and the eternal exposure metal
these do not contact with the printed board. [Note 2] should be more than 1M ohm by
The inside wiring is designed not to get closer using the 500V insulation resistance meter
to the pyrogenic parts and high voltage parts. [Note 1].
Therefore, put these parts in the original 4. If the insulation resistance is less than 1M
positions. ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
[Note 1]
CATHODE-RAY TUBE
If you have not the 500V insulation
In the condition that an explosion-proof cathode- resistance meter, use a Tester.
ray tube is set in this equipment, safety is
secured against implosion. However, when [Note 2]
removing it or serving from backward, it is External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to
deal with it.
A1-2
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the unit’s manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
PORTABLE CART WARNING
8. ACCESSORIES (symbol provided by RETAC)
Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The
unit may fall, causing serious injury, and serious damage to the unit. Use only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
S3125A
9. VENTILATION
Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable
operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The
openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit
should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions
have been adhered to.
10. POWER SOURCES
This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure
of the type of power supply to your home, consult your appliance dealer or local power company. For units
intended to operate from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug. If your unit is equipped with a 3-wire
grounding-type plug, a plug having a third (grounding) pin, this plug will only fit into a grounding-type power
outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they
exit from the appliance.
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit
due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be
fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out
parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
A1-3
IMPORTANT SAFEGUARDS (CONTINUED)
A1-4
IMPORTANT SAFEGUARDS (CONTINUED)
ANTENNA LEAD
IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
A1-5
DISC REMOVAL METHOD AT NO POWER SUPPLY
1. Remove the Back Cabinet and AV PCB/DVD Block. (Refer to item 1 of the DISASSEMBLY
INSTRUCTIONS.)
2. Slide the Rack Loading (White) toward the arrow direction by using a minus driver to release the lock.
(Refer to Fig. 1)
3. Draw the Tray.
Rack Loading
(White) Deck CD
Fig. 1
TRAY LOCK
Tray cannot be opened by setting the Tray Lock, please follow the steps below.
1. Turn Unit ON.
2. Set the DVD to the Stop Mode.
3. Press and hold the '9' key on the remote control unit.
4. Simultaneously press and hold the 'STOP' key on the front panel.
5. Hold both keys for more than 3 seconds.
6. Press the OPEN/CLOSE key on the front panel to check the Tray Lock setting.
NB: No indications on the screen when the Tray Lock is setting.
A1-6
TABLE OF CONTENTS
A2-1
GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 13 inch / 335.4 mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.45G / 0.18G
Color System NTSC
Speaker 2 Speaker
Position Front
Size 1.5 x 2.7 inch
Impedance 8 ohm
Sound Output Max 1.5W + 1.5W
10%(Typical) 1.0W + 1.0W
G-2 DVD System Color System NTSC
Disc DVD, CD-DA, CD-R/RW, Video CD
Disc Diameter 120 mm , 80 mm
Deck Disc Loading System Front Loading
Motor 2 Motors
Pick up 1-Lens 2-Beams System
Playback time(Max) DVD 1-Layer 135min (4.7GB)
DVD 2-Layer 245min (8.5GB)
CD 74min
Video CD 74min
Search speed Fwd 2-20 times / 4 step
Actual 2-45 times (DVD, VIDEO CD)
4-40 times (CD)
Rev 2-20 times / 4 step
Actual 2-45 times (DVD, VIDEO CD)
4-40 times (CD)
Slow speed Fwd 1/7 - 1/2 times
Actual --
Rev 1/7 - 1/2 times
Actual --
G-3 Tuning Broadcasting System US System M
System Tuner and System 1Tuner
Receive CH Destination US(w/CATV)
Tuning System F-Synth
Input Impedance VHF/UHF 75 Ohm
CH Coverage 2~69, 4A, A-5~A-1, A~I, J~W, W+1~W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.50MHz
Preset CH No
Stereo/Dual TV Sound US-Stereo
Tuner Sound Muting Yes
G-4 Signal Video Signal Input Level 1 V p-p/75 ohm
Output Level --
S/N Ratio (Weighted) --
Horizontal Resolution at DVD Mode --
--
RGB Signal Output Level --
Audio Signal Input Level -8.0dBm/50k ohm
Output Level --
Digital Output Level 0.5 V p-p/75 ohm
S/N Ratio at DVD (Weighted) --
Harmonic Distortion --
Frequency Response : at DVD --
at Video CD --
at SVCD --
at CD --
G-5 Power Power Source AC 120V, 60Hz
DC --
Power Consumption at AC 75W at 120V 60Hz
at DC --
Stand by (at AC) 5W at 120V 60Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
G-6 Regulation Safety UL
Radiation FCC
X-Radiation DHHS
Laser DHHS
G-7 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-8 Operating Humidity Less than 80% RH
A3-1
GENERAL SPECIFICATIONS
G-9 On Screen Menu(TV) Yes
Display Menu Type Icon
TV Setup Yes
Picture Yes
Audio No
Picture Preference Yes
Channel Setup Yes
TV/CATV Yes
Auto CH Memory Yes
Add/ Delete Yes
V-chip Setup Yes
Language Yes
Sleep Timer Yes
CH / AV(LINE) / DVD Yes
Stereo/Audio Output Yes
Bilingual No
SAP Yes
Control Volume Yes
Level Bright / Contrast / Sharpness / Color Yes
Tint Yes
Bass/Treble/Balance No
Caption / Text Yes
Auto Search/Position No
Game Yes
Mute Yes
A3-2
GENERAL SPECIFICATIONS
G-10 On Screen Menu (DVD) Yes
Display Menu Type Character
Language Yes
Menu Yes
Subtitle Yes
Audio Yes
Picture Yes
TV Screen Size Yes
OSD Display On/Off Yes
JPEG Interval No
Select Files No
Sound Yes
DRC (Dynamic Range Control) Yes
dts Decode No
Output(5.1ch/ 2ch) No
Surround On/Off No
Center On/Off No
Sub Woofer On/Off No
Parental Yes
Password Lock/ Un Lock Yes
Rating Level Yes
Other Yes
OSD Language(Set up Language) Yes
Output(RGB/Composite) No
Open Yes
Close Yes
No disc Yes
Reading Yes
Play Yes
Still/Pause Yes
Stop Yes
Prohibit Mark Yes
Step Yes
Skip(>>|) Yes
Skip(|<<) Yes
Random Yes (CD, VIDEO CD )
Repeat Yes
Slow+ ## Yes
Slow- ## Yes
Search+ ## Yes
Search- ## Yes
Jump Yes
Resume Yes
Title No. Yes
Chapter No. Yes
Track No. Yes
Time Yes
Sub Title No. Yes
Angle No. Yes
Vocal On/Off Yes
Audio No. Yes
Audio Stereo L/R Yes (Video CD)
Zoom Yes
Marker No. No
Program Play Back Yes (CD, VIDEO CD)
Surround On/Off No
Screen Saver No
JPEG Folder Name No
File Name No
File No No
Time No
Track No No
G-11 OSD Language (TV) English, French, Spanish
(DVD) English, French, Spanish
G-12 Clock and Sleep Timer Max Time 120 Min
Timer Step 10 Min
On/Off Timer Program(On Timer / Off Timer) No
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec
A3-3
GENERAL SPECIFICATIONS
G-13 Remote Unit RC-GD
Control Glow in Dark Remocon Yes
Format NEC
Custom Code 71-8E h
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 45 Key
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
Play Yes
Stop Yes
Search+ Yes
Search- Yes
Skip+ Yes
Skip- Yes
Slow+ Yes
Slow- Yes
Pause Yes
Call Yes
TV/DVD Yes
Cancel Yes
Audio Select Yes
Angle Yes
Subtitle Yes
Top Menu Yes
Set up/ Menu Yes
DVD Menu Yes
Return Yes
Up/ Set+/ CH Up Yes
Down/ Set-/ CH Down Yes
Left/Select-/Vol Down Yes
Right/Select+/Vol Up Yes
Select/ Enter Yes
Play Mode Yes
Closed Caption Yes
Input Select Yes
Repeat A-B Yes
Zoom/ Quick View Yes
Mute Yes
Open/Close Yes
Sleep Yes
Jump Yes
Game Yes
A3-4
GENERAL SPECIFICATIONS
G-14 Features CATV Yes
Auto Shut Off Yes
Auto CH Memory Yes
V-Chip USA V-chip Yes
CANADA V-chip No
Auto Search No
SAP Yes
Game Position Yes
FM Transmitter No
Energy Star No
Closed Caption Yes
Comb Filter No
Protect of FBT Leak Circuit Yes
Choke Coil No
Power On Memory No
Tray Lock Yes
Parental Lock (DVD Only) Yes
Video CD Playback Yes
SVCD Playback No
Overlay Graphics And Text No
Command List No
Entry Point Jump No
MP3 Playback No
WMA Playback No
JPEG Playback No
Digital Out (Dolby Digital) Yes
(MPEG) Yes
(PCM) Yes
(DTS) Yes
Down Mix Out (Dolby Digital) Yes
(DTS) No
Surround (Tru Surround) No
Screen Saver No
Picture Preference Yes
Auto Setup Yes
Audio DAC 192kHz / 24bit
G-15 Accessories Owner's Manual Language English
w/Guarantee Card Yes
Remote Control Unit Yes
Battery Yes
UM size x pcs UM-4 x 2 pcs
OEM Brand No
Rod Antenna No
Poles No
Terminal --
Loop Antenna No
Terminal --
U/V Mixer No
300 ohm to 75 ohm Antenna Adapter Yes
Antenna Change Plug No
Guarantee Card No
Registration Card Yes
Warranty Card No
ESP Card No
Service Station List No
DC Car Cord (Center+) No
Columbia Offer Sheet No
Sheet Information (Return) Yes
A3-5
GENERAL SPECIFICATIONS
G-16 Interface Switch Front Power (Tact) Yes
Channel Up Yes
Channel Down Yes
Volume Up Yes
Volume Down Yes
Play Yes
Open/Close Yes
Skip(>>|) Yes
Skip(|<<) Yes
Still/Pause No
Stop Yes
Main Power SW No
Rear Main Power SW No
Indicator Power Yes (Red)
Stand-by No
On Timer No
Terminals Front Video Input RCA x 1
Audio Input RCA x 2(Stereo)
Other Terminal Head Phone
Rear Video Input No
Audio Input No
Video Output No
Audio Output No
Digital Audio Output Coaxial (DVD Only)
Diversity No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
G-17 Set Size Approx. W x D x H (mm) 362x365x382
G-18 Weight Net (Approx.) 11.0kg (24.3lbs)
Gross (Approx.) 12.5kg (27.6lbs)
G-19 Carton Master Carton No
Content --- Sets
Material --- / ---
Dimensions W x D x H(mm) ---
Description of Origin ---
Gift Box Yes
Material Double/Full Color
W/Color Photo Label No
Dimensions W x D x H(mm) 423x447x443
Design As Per Buyer 's
Description of Origin Yes
Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height (cm) 62
Container Stuffing (40' container) 700 Sets
G-20 Material Cabinet Front PS 94V0 DECABROM
Rear PS 94V0 DECABROM
Jack Panel -
PCB Non-Halogen Demand No
Eyelet Demand Yes
G-21 Environment Pb Free Lead-free Solder No
Other No
Cd Free No
A3-6
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS 1-3: AV PCB/DVD BLOCK (Refer to Fig. 1-3)
AND P.C. BOARDS 1. Remove the 2 screws 1.
2. Disconnect the following connectors:
1-1: BACK CABINET (Refer to Fig. 1-1)
(CP301, CP302, CP401 and CP3800).
1. Remove the 4 screws 1. 3. Remove the AV PCB/DVD Block in the direction of arrow.
2. Remove the screw 2 which are used for holding the Back
Cabinet. 1 1
3. Remove the AC cord from the AC cord hook 3.
4. Remove the Back Cabinet in the direction of arrow.
Front Cabinet
Front Cabinet
AV PCB/DVD Block
1
Fig. 1-3
1
2 1-4: DVD BLOCK (Refer to Fig. 1-4)
3
Back Cabinet 1. Remove the 11 screws 1.
1 2. Remove the Top Shield in the direction of arrow (A).
Fig. 1-1 3. Disconnect the following connectors:
(CP8001 and CP8002).
4. Remove the 4 screws 2.
1-2: CRT PCB (Refer to Fig. 1-2)
5. Remove the DVD Block in the direction of arrow (B).
CAUTION: BEFORE REMOVING THE ANODE CAP, 6. Remove the screw 3.
DISCHARGE ELECTRICITY BECAUSE IT 7. Remove the Jack Shield.
CONTAINS HIGH VOLTAGE. 8. Remove the AV PCB in the direction of arrow (C).
BEFORE ATTEMPTING TO REMOVE OR
REPAIR ANY PCB, UNPLUG THE POWER 1 1
1
CORD FROM THE AC SOURCE.
1 1
1. Remove the Anode Cap. 1 1
Top Shield
(Refer to REMOVAL OF ANODE CAP)
2. Disconnect the following connector: 1 1
(CP801). 1
1 2
3. Remove the CRT PCB in the direction of arrow.
(A) 2 2
Front Cabinet CRT PCB
DVD Block
(B)
AV PCB
3
Jack Shield
(C)
B1-1
DISASSEMBLY INSTRUCTIONS
1-5: DVD PCB/DVD DECK (Refer to Fig. 1-5)
1. Make the short circuit on the position as shown Fig. 1-5
using a soldering. If you remove the DVD Deck with no
soldering, the Laser may be damaged.
2. Unlock the 2 supports 1.
3. Remove the Front Tray Plate in the direction of arrow (A).
4. Disconnect the following connectors:
(CP2601, CP2602 and CP2603).
5. Remove the 4 screws 2.
6. Remove the DVD Deck in the direction of arrow (B).
7. Remove the 4 screws 3.
8. Remove the DVD PCB in the direction of arrow (C).
2 2
DVD Deck
2
Pick Up PCB
3
(B)
3
3
DVD PCB
(C)
Deck Angle
Fig. 1-5
NOTE
When the installation of the DVD Deck, remove all the
soldering on the short circuit position after the connection of
Pick Up PCB and DVD PCB connector.
B1-2
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF DVD DECK PARTS Main Chassis Ass’y
NOTE
1. Do not disassemble the DVD DECK PARTS except listed Rack Loading
1
Tray Fig. 2-2-B
Main Frame Ass’y
Tray
Rack Loading
Main Gear
Rack Loading Spring
Rack L Spring
1
Main Frame Ass’y Fig. 2-1-B Fig. 2-3
2-2: MAIN CHASSIS ASS’Y (Refer to Fig. 2-2-A) 2-4: CLAMPER ASS’Y/INSULATOR(R)/LEVER SWITCH
(Refer to Fig. 2-4-A)
1. Remove the Main Chassis Ass’y from the Insulator (R).
2. Unlock the support 1. 1. Remove the screw 1.
3. Remove the Main Chassis Ass’y. 2. Remove the Lever Switch.
3. Remove the 2 Insulator (R).
Insulator (R) 4. Press the Clamper and rotate the Clamper Plate clockwise,
(Green) then unlock the 3 supports 2.
5. Remove the Clamper Plate, Clamper Magnet and Clamper.
1 Insulator (R)
Main Frame Ass’y (Green) Insulator (R)
(Green)
Clamper Plate
Clamper Magnet
Main Frame
Fig. 2-2-A
1
Red
White Switch PCB Ass'y
Blue From DVD PCB
Fig. 2-4-B
NOTE
1. When installing the wire of the Switch PCB, install it
correctly as Fig. 2-6-B.
Fig. 2-4-C
Switch PCB Ass'y
Black
From Relay PCB
White
Lever Switch
Insulator (F)
(Black) Rack Feed Lever
Insulator (F)
(Black)
Fig. 2-5-A
NOTE
1. After the installing of the Traverse Holder, check if the • Screw Torque: 3.5 ± 0.5kgf•cm Fig. 2-7-A
wire is like Fig. 2-5-B.
B2-2
DISASSEMBLY INSTRUCTIONS
NOTE 2-9: GEAR (Refer to Fig. 2-9-A)
1. After the assembly of the Rack Feed, check if the Rack 1. Unlock the support 1.
Feed 1/2 is moving smoothly. (Refer to Fig. 2-7-B) 2. Remove the Middle Gear 1/2/3, Idler Gear and Feed Gear.
2. In case of the Rack Feed Ass’y installation, install cor-
rectly as Fig. 2-7-C.
Middle Gear 2
Middle Gear 3
Feed Gear
Idler Gear
Moving smoothly
Fig. 2-7-B
NOTE
1. When installing the wire of the Relay PCB, install it Middle Gear 2
Fig. 2-9-C
correctly as Fig. 2-8-B.
Idler Arm
Fig. 2-8-B
B2-3
DISASSEMBLY INSTRUCTIONS
2-11: FEED MOTOR (Refer to Fig. 2-11-A)
1. Remove the 2 screws 1.
2. Remove the Feed Motor.
3. Remove the Motor Gear.
11
Motor Gear
Feed Motor
NOTE
1. In case of the Motor Gear installation, check if the value
of the Fig. 2-11-B is correct.
2. When installing the Feed Motor, check if the cable is
positioned as Fig. 2-11-C.
Motor Gear
6.1 ± 0.1mm
Feed Motor
Feed Motor
B2-4
DISASSEMBLY INSTRUCTIONS
3. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
Take care not to damage the Rubber Cap.
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage. INSTALLATION
* Do not use pliers to loosen or tighten the Anode Cap
1. Clean the spot where the cap was located with a small
terminal, this may cause the spring to be damaged.
amount of alcohol. (Refer to Fig. 3-3.)
REMOVAL
NOTE
1. Follow the steps as follows to discharge the Anode Cap. Confirm that there is no dirt, dust, etc. at the spot where
(Refer to Fig. 3-1.) the cap was located.
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver, Location of Anode Cap
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
Fig. 3-3
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 3-4.)
Screwdriver CRT
Support
Alligator Clip
2. Flip up the sides of the Rubber Cap in the direction of the 4. Insert one end of the Anode Support into the anode button,
arrow and remove one side of the support. then the other as shown in Fig. 3-5.
(Refer to Fig. 3-2.)
Rubber Cap
Support
CRT
CRT Fig. 3-5
Support
Fig. 3-2
5. Confirm that the Support is securely connected.
6. Put on the Rubber Cap without moving any parts.
B3-1
DISASSEMBLY INSTRUCTIONS
4. REMOVAL AND INSTALLATION OF FLAT 3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
PACKAGE IC a tweezers and remove the IC by moving with the IC
REMOVAL desoldering machine. (Refer to Fig. 4-3.)
1. Put the Masking Tape (cotton tape) around the Flat NOTE
Package IC to protect other parts from any damage.
Some ICs on the PCB are affixed with glue, so be
(Refer to Fig. 4-1.)
careful not to break or damage the foil of each IC
NOTE leads or solder lands under the IC when removing it.
Masking is carried out on all the parts located within
10 mm distance from IC leads.
Blower type IC
desoldering machine
IC
Masking Tape
(Cotton Tape)
Tweezers
Fig. 4-1
Soldering Iron
IC
Fig. 4-2 IC pattern
Fig. 4-4
B4-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-
1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 4-8.)
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
IC
(Refer to Fig. 4-5.)
Thin-tip Soldering Iron
Soldering Iron
Fig. 4-8
2. Supply the solder from the upper position of IC leads When the IC leads are bent during soldering and/or
sliding to the lower position of the IC leads. repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
(Refer to Fig. 4-6.)
damaged. So, always be sure to replace the IC in this
case.
Soldering Iron
Solder
IC Supply soldering
from upper position
to lower position
Fig. 4-6
Soldering Iron
IC
Fig. 4-7
B4-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control
for more than a standard time (second).
Standard Time
Set Key Remocon Key Operations
(seconds)
C-1
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: No need setting for after INI 27.
INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
00 06 0F 44 20 D0 35 30 25 15 54 03 00 C8 55 0F 47
10 30 50 50 04 15 77 23 50 20 77 52 00 02 11 00 00
Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
ADDRESS DATA
INIT 00 06
CRT ON 0010
FIG. 1
3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS
until required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
C-2
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL
NO. FUNCTION NO. FUNCTION
ADJUSTMENTS 01 OSD H 39 TINT AV
02 OSD CONTRAST 40 SHARPNESS AV
Read and perform these adjustments when repairing the 03 CUT OFF 41 SUB BIAS
04 H POSITION 42 BRI. DVD(CENT.)
circuits or replacing electrical parts or PCB assemblies. 05 H BLK L 43 BRI. DVD(MAX)
06 H BLK R 44 BRI. DVD(MIN)
CAUTION 07 V SIZE 45 CONT. DVD(CENT.)
08 V POSITION 46 CONT. DVD(MAX)
• Use an isolation transformer when performing any service 09 V LINEARITY 47 CONT. DVD(MIN)
10 V S CORRECTION 48 COL. DVD(CENT.)
on this chassis. 11 V COMP 49 COL. DVD(MAX)
• Before removing the anode cap, discharge electricity 12 R CUT OFF 50 COL. DVD(MIN)
13 G CUT OFF 51 TINT DVD
because it contains high voltage. 14 B CUT OFF 52 SHARPNESS DVD
• When removing a PCB or related component, after 15 R DRIVE 53 SUB BIAS
16 G DRIVE 54 BRI. GAME(CENT.)
unfastening or changing a wire, be sure to put the wire 17 B DRIVE 55 BRI. GAME(MAX)
back in its original position. 18 BRIGHTNESS(CENT.) 56 BRI. GAME(MIN)
19 BRIGHTNESS(MAX) 57 CONT. GAME(CENT.)
• When you exchange IC and Transistor for a heat sink, 20 BRIGHTNESS(MIN) 58 CONT. GAME(MAX)
apply the silicon grease on the contact section of the heat 21 CONTRAST(CENT.) 59 CONT. GAME(MIN)
22 CONTRAST(MAX) 60 SUB BIAS
sink. Before applying new silicon grease, remove all the old 23 CONTRAST(MIN) 61 TUNING V MUTE
silicon grease. (Old grease may cause damages to the IC 24 COLOR(CENT.) 62 POWER ON V MUTE
25 COLOR(MAX) 63 INPUT LEVEL
and Transistor). 26 COLOR(MIN) 64 SEPARATION L
27 TINT 65 SEPARATION H
Prepare the following measurement tools for electrical 28 SHARPNESS 66 X-RAY TEST
29 SUB BIAS 67 H STOP
adjustments. 30 BRI. AV(CENT.) 68 H FREQ
31 BRI. AV(MAX) 69 BAST/WEST DC
1. Oscilloscope 32 BRI. AV(MIN) 70 BAST/WEST AMP
33 CONT. AV(CENT.) 71 BAST/WEST TILT
2. Digital Voltmeter 34 CONT. AV(MAX) 72 BAST/WEST COR, TOP
3. AC Voltmeter 35 CONT. AV(MIN) 73 BAST/WEST COR, BOT
36 COL. AV(CENT.) 74 H SIZE COMP
4. Pattern Generator 37 COL. AV(MAX) 75 H BLK L AV
5. Multi-Sound Signal Generator 38 COL. AV(MIN) 76 H BLK R AV
Fig. 1-2
On-Screen Display Adjustment
1. Set the VOLUME to minimum. 2. BASIC ADJUSTMENTS
2. Press the VOL. DOWN button on the set and the Channel 2-1: CONSTANT VOLTAGE
button (9) on the remote control for more than 1 second
to appear the adjustment mode on the screen as shown 1. Set condition is AV MODE without signal.
in Fig. 1-1. 2. Using the remote control, set the brightness and contrast
to normal position.
3. Connect the digital voltmeter to TP401.
Function 01 OSD 4. Adjust the VR3800 until the digital voltmeter is 135 ± 0.5V.
Step No. 12
2-2: FOCUS
1. Receive the monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.
D-1
ELECTRICAL ADJUSTMENTS
2-4: WHITE BALANCE 2-8: VERTICAL LINEARITY
NOTE: Adjust after performing CUT OFF adjustment. NOTE: Adjust after performing adjustments in section 2-7.
1. Place the set with Aging Test for more than 15 minutes. After the adjustment of Vertical Linearity, reconfirm
2. Receive the gray scale pattern from the Pattern the Vertical Position and Vertical Size adjustments.
Generator. 1. Receive the monoscope pattern.
3. Using the remote control, set the brightness and contrast 2. Using the remote control, set the brightness and contrast
to normal position. to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and 3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to press the channel button (09) on the remote control to
select "G DRIVE". select "VLIN".
5. Press the CH. UP/DOWN button on the remote control to 4. Press the VOL. UP/DOWN button on the remote control
select the "R CUT OFF", "G CUT OFF", "B CUT OFF", "R until the SHIFT quantity of the OVER SCAN on upside
DRIVE" or "B DRIVE". and downside becomes minimum.
6. Adjust the VOL. UP/DOWN button on the remote control
to whiten the R CUT OFF, G CUT OFF, B CUT OFF, R 2-9: SEPARATION
DRIVE, and B DRIVE at each step tone sections equally.
Please do the method (1) or method (2) adjustment.
7. Perform the above adjustments 5 and 6 until the white
color is looked like a white. Method (1)
1. Set the multi-sound signal generator for each different L-
2-5: HORIZONTAL POSITION ch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz)
1. Receive the monoscope pattern. and receive the RF signal.
2. Using the remote control, set the brightness and contrast 2. Connect the oscilloscope to the Audio Out Jack.
to normal position. 3. Press the AUDIO button on the remote control to set to
3. Activate the adjustment mode display of Fig. 1-1 and the stereo mode.
press the channel button (04) on the remote control to 4. Activate the adjustment mode display of Fig. 1-1 and
select "HPOSI". press the channel button (64) on the remote control to
4. Press the VOL. UP/DOWN button on the remote control select “SEPAL”.
until the SHIFT quantity of the OVER SCAN on right and 5. Press the VOL. UP/DOWN button on the remote control
left becomes minimum. to adjust it until the audio output wave becomes a fine
sine wave.
2-6: VERTICAL POSITION 6. Press the CH UP button 1 time to set to "SEPAH" mode.
1. Receive the monoscope pattern. 7. Press the VOL. UP/DOWN button on the remote control
2. Using the remote control, set the brightness and contrast to adjust it until the audio output wave becomes a fine
to normal position. sine wave.
3. Activate the adjustment mode display of Fig. 1-1 and
Method (2)
press the channel button (08) on the remote control to
select "VPOSI". 1. Set the multi-sound signal generator L-ch=1KHz, R-ch
4. Check if the step No. V POSI is "02". =Non input and receive the RF signal.
5. Adjust the VR401 until the horizontal line becomes fit 2. Connect the oscilloscope to the Audio Out Jack (R-ch).
to notch of the shadow mask. 3. Press the AUDIO button on the remote control to set to
the stereo mode.
2-7: VERTICAL SIZE 4. Activate the adjustment mode display of Fig. 1-1 and
1. Receive the monoscope pattern. press the channel button (64) on the remote control to
2. Using the remote control, set the brightness and contrast select “SEPAL”.
to normal position. 5. Press the VOL. UP/DOWN button on the remote control
3. Activate the adjustment mode display of Fig. 1-1 and to adjust it until the R-ch output becomes minimum.
press the channel button (07) on the remote control to 6. Press the CH UP button 1 time to set to "SEPAH" mode.
select "VSIZE". 7. Press the VOL. UP/DOWN button on the remote control
4. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum.
until the Up/Down OVER SCAN Quantity becomes equal 8. Set the multi-sound signal generator L-ch=Non input,
to the Right/Left OVER SCAN Quantity. R-ch=1KHz and receive the RF signal.
5. Receive a broadcast and check if the picture is normal. 9. Connect the oscilloscope to the Audio Out Jack (L-ch).
Then perform the above adjustments 3~7.
D-2
ELECTRICAL ADJUSTMENTS
2-10: OSD HORIZONTAL 2-13: TINT CENTER
1. Activate the adjustment mode display of Fig. 1-1. 1. Receive the color bar pattern. (RF Input)
2. Press the VOL. UP/DOWN button on the remote control 2. Using the remote control, set the brightness, contrast,
until the difference of A and B becomes minimum. color and tint to normal position.
(Refer to Fig. 2-1) 3. Connect the oscilloscope to TP024.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (27) on the remote control to
01 OSD select "TNTC".
12 5. Press the VOL. UP/DOWN button on the remote control
until the section "A" becomes a straight line.
(Refer to Fig. 2-2)
6. Receive the color bar pattern. (Audio Video Input)
7. Press the INPUT SELECT button on the remote control
to set to the AV mode.
8. Using the remote control, set the brightness, contrast,
color and tint to normal position.
A B Fig. 2-1 9. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (39) on the remote control to
select "TNTCA".
2-11: LEVEL 10. Press the VOL. UP/DOWN button on the remote control
1. Receive the VHF HIGH (70dB). until the section "A" becomes a straight line.
2. Connect the AC voltmeter to pin 6 of CP101. (Refer to Fig. 2-2)
3. Activate the adjustment mode display of Fig. 1-1 and 11. Press the TV/DVD button on the remote control to set to
press the channel button (63) on the remote control to the DVD mode.
select "LVL". 12. Activate the adjustment mode display of Fig. 1-1 and
4. Press the VOL. UP/DOWN button on the remote control press the channel button (51) on the remote control to
until the AC voltmeter is 75 ± 2mV. select "TNTCD".
13. Press the VOL. UP/DOWN button on the remote control
2-12: BRIGHT CENTER to set the same step numbers as the AV.
1. Receive the monoscope pattern. (RF Input)
2. Using the remote control, set the brightness and contrast
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select "BRTC".
4. Press the VOL. UP/DOWN button on the remote control
until the white 15% is starting to be visible
5. Receive the monoscope pattern. (Audio Video Input) "A"
6. Press the INPUT SELECT button on the remote control
to set to the AV mode. Fig. 2-2
7. Using the remote control, set the brightness and contrast
to normal position.
8. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (30) on the remote control to
select "BRTCA".
9. Press the VOL. UP/DOWN button on the remote control
until the white 15% is starting to be visible
10. Press the TV/DVD button on the remote control to set to
the DVD mode.
11. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (42) on the remote control to
select "BRTCD".
12. Press the VOL. UP/DOWN button on the remote control
to set the same step numbers as the AV.
13. Press the GAME button on the remote control to set to
the GAME mode.
14. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (54) on the remote control to
select "BRTCG".
15. Press the VOL. UP/DOWN button on the remote control
to set the same step numbers as the AV.
D-3
ELECTRICAL ADJUSTMENTS
2-14: COLOR CENTER 2-15: CONTRAST MAX
1. Receive the color bar pattern. (RF Input) 1. Activate the adjustment mode display of Fig. 1-1 and
2. Using the remote control, set the brightness, contrast, press the channel button (22) on the remote control to
color and tint to normal position. select "CNTX".
3. Connect the oscilloscope to TP022. 2. Press the VOL. UP/DOWN button on the remote control
4. Activate the adjustment mode display of Fig. 1-1 and until the contrast step No. becomes "5A"
press the channel button (24) on the remote control to 3. Receive a broadcast and check if the picture is normal.
select "COLC". 4. Press the INPUT SELECT button on the remote control
5. Adjust the VOLTS RANGE VARIABLE knob of the to set to the AV mode.
oscilloscope until the range between white 100% and 0% 5. Activate the adjustment mode display of Fig. 1-1 and
is set to 4 scales on the screen of the oscilloscope. press the channel button (34) on the remote control to
6. Press the VOL. UP/DOWN button on the remote control select "CNTXA".
until the red color level is adjusted to 110 ± 5% of the 6. Press the VOL. UP/DOWN button on the remote control
white level. (Refer to Fig. 2-3) until the contrast step No. becomes "5A"
7. Receive the color bar pattern. (Audio Video Input) 7. Receive a broadcast and check if the picture is normal.
8. Press the INPUT SELECT button on the remote control 8. Press the TV/DVD button on the remote control to set to
to set to the AV mode. the DVD mode.
9. Using the remote control, set the brightness, contrast, 9. Activate the adjustment mode display of Fig. 1-1 and
color and tint to normal position. press the channel button (46) on the remote control to
10. Activate the adjustment mode display of Fig. 1-1 and select "CNTXD".
press the channel button (36) on the remote control to 10. Press the VOL. UP/DOWN button on the remote control
select "COLCA". to set the same step numbers as the AV.
11. Adjust the VOLTS RANGE VARIABLE knob of the 11. Press the GAME button on the remote control to set to
oscilloscope until the range between white 100% and 0% the GAME mode.
is set to 4 scales on the screen of the oscilloscope. 12. Activate the adjustment mode display of Fig. 1-1 and
12. Press the VOL. UP/DOWN button on the remote control press the channel button (58) on the remote control to
until the red color level is adjusted to 110 ± 5% of the select "CNTXG".
white level. (Refer to Fig. 2-3) 13. Press the VOL. UP/DOWN button on the remote control
13. Press the TV/DVD button on the remote control to set to to set the same step numbers as the AV.
the DVD mode.
14. Activate the adjustment mode display of Fig. 1-1 and 2-16: Confirmation of Fixed Value (Step No.)
press the channel button (48) on the remote control to
Please check if the fixed values of the each adjustment
select "COLCD".
items are set correctly referring below.
15. Press the VOL. UP/DOWN button on the remote control
to decrease the step numbers by 8 steps to the AV. NO. FUNCTION STEP NO. NO. FUNCTION STEP NO.
02 OSD CONTRAST 04 44 BRI. DVD(MIN) 2A
05 H BLK L 04 45 CONT. DVD(CENT.) 40
White 0% 06 H BLK R 00 47 CONT. DVD(MIN) 10
08 V POSITION 02 49 COL. DVD(MAX) 70
10 V S CORRECTION 08 50 COL. DVD(MIN) 10
11 V COMP 03 52 SHARPNESS DVD 10
16 G DRIVE 07 53 SUB BIAS 00
19 BRIGHTNESS(MAX) 70 55 BRI. GAME(MAX) 70
20 BRIGHTNESS(MIN) 2A 56 BRI. GAME(MIN) 2A
21 CONTRAST(CENT.) 40 57 CONT. GAME(CENT.) 40
23 CONTRAST(MIN) 10 59 CONT. GAME(MIN) 10
100% 25 COLOR(MAX) 70 60 SUB BIAS 00
26 COLOR(MIN) 10 61 TUNING V MUTE 00
28 SHARPNESS 18 62 POWER ON V MUTE 40
29 SUB BIAS 00 68 H FREQ 3F
31 BRI. AV(MAX) 70 69 BAST/WEST DC 00
32 BRI. AV(MIN) 2A 70 BAST/WEST AMP 00
33 CONT. AV(CENT.) 40 71 BAST/WEST TILT 00
35 CONT. AV(MIN) 10 72 BAST/WEST COR, TOP 00
White 100% Red Level Fig. 2-3 37 COL. AV(MAX) 70 73 BAST/WEST COR, BOT 00
38 COL. AV(MIN) 10 74 H SIZE COMP 00
40 SHARPNESS AV 10 75 H BLK L AV 07
41 SUB BIAS 00 76 H BLK R AV 05
43 BRI. DVD(MAX) 70
D-4
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 3-2.
1. Receive the crosshatch pattern from the color bar
1. Turn the unit on and let it warm up for at least 30
generator.
minutes before performing the following adjustments.
2. Combine red and blue of the 3 color crosshatch pattern
2. Place the CRT surface facing east or west to reduce the
on the center of the screen by adjusting the pair of
terrestrial magnetism.
4 pole magnets.
3. Turn ON the unit and demagnetize with a Degauss Coil.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted 3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar 1. Adjust the differences around the screen by moving
generator. the deflection yoke upward/downward and right/left.
3. Slide the deflection yoke until it touches the funnel (Refer to Fig. 3-2-a)
side of the CRT. 2. Insert three wedges between the deflection yoke and
4. Adjust center of screen to green, with red and blue on the CRT funnel to fix the deflection yoke.
sides, using the pair of purity magnets. (Refer to Fig. 3-2-b)
5. Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
RGB RGB
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets. R
7. Combine red/blue (magenta) and green by adjusting the G
pair of 6 pole magnets. B
8. Adjust the crosshatch pattern to change to white R
G
by repeating steps 6 and 7. B
3-2: PURITY
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE
Fig. 3-2-a
Adjust after performing adjustments in section 3-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide. WEDGE WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the WEDGE
screen, then tighten the fixing screw.
DEFLECTION YOKE WEDGE POSITION
DEFLECTION YOKE SCREW
Fig. 3-2-b
MAGNET SCREW
6 POLE MAGNETS
4 POLE MAGNETS
PURITY MAGNETS
Fig. 3-1
D-5
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CP801
CD805
CRT PCB
TP024
TP022
J801
CRT CP802B
CP803B
CD803
CD802
FB401
CP803A
TP401
CRT
CD3800
CP401
AC IN
CP101
CP3800
CRT
CP802A
CP8002
VR401
CD302
CP302
CD301
CP301
SPEAKER
CP8001
SPEAKER
CD8501
J2201
J2202
J2203
J2204
AV PCB
DVD DECK
CP8502
CP2601
CD8505
CP2602
CP2601
DVD PCB
CD2301
CD2001
CD2302
D-6
DVD BLOCK DIAGRAM
SDD0~SDD15
HA0~HA20,
HD0~HD15 SDA0~SDA11
VCR BLOCK
DVD LOADER CD4002
DM II
RFA_SDEN, DATA, SCLK
A, B, C, D, E, F
READ CHANNEL TX
AAF_CE, FE, TE, PI
Pick up RF IC2601 RX
ZR36708TQC FNN, FNP P.CON+3.3V
CD, DVD, LD
VBIASS0, S1 P.CON+5V
DEFECT, LINK, MIRR, LDON P.CON+9V
MPEG/MICON/DSP
Loading IC4001 REG+1.8V SPDIF
Motor ZR36762 IC4003
SPDL+/– Dual OP-AMP SPDL_SENS PQ070XZ01ZP
IC2602
BA10358F-E2
Spindle/
Sled CP8502
Motor HOME, TIN SW, TOUT SW
DVD RESET
ASDATA0
AMCLK
ABCLK
ALRCLK
DVD AUDIO L
STEREO DAC
IC8502 DVD AUDIO R
PCM1742KEG/2K
E-1 E-2
TV BLOCK DIAGRAM
VOL DOWN
CH DOWN
VOL UP
CH UP
RESET
IC103 PST3231NR
1 2 *A
*A
POWER 33
ON/OFF TU001
18 22
SCL SDA
OPEN/CLOSE 17 23 10 11
MICON 24
STOP IC101 26
31
OEC6079A
X101 27
PLAY 16MHz
32 36
Q105
SKIP FF
6 11 12 38 37 4 BUFFER
SKIP REW
*B *C
DVD C
DVD Y 57
DVD_RESET 56
RX
55
TX R.OUT
14
59 G.OUT
AMP 15 V801
DVD_A_OUT_L 3 IC4201 1 Q4209~Q4212 40 B.OUT CRT
L 16
NJM4580M
MUTE SW 30
DVD_A_OUT_R 5 (TE1) 7
R 51 DY801 3 9 7
19 18 45
24 50 F 8
3
*E 23 SOUND V.OUT
Q4203 DECORDER 19 1
IC401
IC902 AN5522
ZERO MUTE *D FB401
2 AN5829S 42 Q405 Q406
Q305 CHROMA
BUFFER IC601 LA76319M-MPB-E
Q301
Q302 MUTE
BUFFER
9 2 SPEAKER
4 SP351
SOUND AMP SPEAKER
IC302 12
2 2 2 2 6 SP352
AN7522N 10
V L R
J4201 J2202 J2203 8
J2204 *A---AT+5.6V
*B---P.CON+9V
SOUND+B *C---CHROMA+5V
HEADPHONE
*D---P.CON+A5V
J2201
*E---P.CON+12V
E-3 E-4
POWER BLOCK DIAGRAM
Q3003, Q3004,
Q3007
P.CON+3.3V OUT P.CON+3.3V
5V REG.
DVD_H
IC3001 KIA7805API
1 3 P.CON+D5V
L3800
DEGAUSS COIL
Q3008
DRIVE AT+5.6V
TRANSFORMER
D3808, D3809, SWITCHING
F3800 D3815, D3816 T3800
AC IN
RECTIFIER
10
12 SOUND+B
IC3800 5V REG.
8 IC3002 KIA7805API
Q3800 PS2561L1-1-V(W) Q3803
FEED BACK 18 1 3 P.CON+5V
FEED BACK POWER 5
CONTROL
+9V REG.
IC3005 KIA7809API
+B ADJ.
VR3800
Q3010
17 DRIVE 1 2 P.CON+D9V
14
Q3005
DRIVE P.CON+9V
Q3000
DRIVE P.CON+12V
Q3001
SW
POWER ON-H
+B
FB401
E-5 E-6
PRINTED CIRCUIT BOARDS
R2330 R2337
R2331 R2325 C2312
B2604 C2306 C2311
R2328
C2657
C2642
R2327 C2309 C2310
C2645
C2643_1 HS2301 R2324 R2334
C2658
R2648 R2322 C2305 R2345
B2603
C2659
C2649
R2304
C2646_1 R2321 R2318 R2344
R2631
R2316
IC2602
C4012 IC4003
R2611 R2308
R2613
R2612
C2303
IC2301
R2307 C2304 R4033
R2649
R2625 R2632 R2305 W863 R4032
R2630 R2629 R2605
R4057
R2628 R2627 R2610
R2306
C2622
C2621
R2312
R2313
W861 R2608 R4034
R2646 C2618 C2620 W862
R2607 C4011_1 C4015
C2655 C2619
B4007
R2644
C2654 R2614 C2633
R2645
R2643 C2616
CP2602
C4043
R4013
C4042
C2623
R4011
R2635
R2602 R2604
C2632
R2603
C2301
R2310
R2314
R2309
W882
C2613 C4063_1 W805
D4001
C4097
C2612 Q4004
R2653
R2651
W875 W854
R2650 C2610
33 49 C2628 C4091
R4040
C2629
CP2603
R2601
C2627
IC2601
IC4007
R4041
R4022
C2624
R2652
C4062
C2625
17 1
C2626
C2635
C2611 L4001
C4064
W807
CD4002
W808 C2609
C4092
C4099
B4006
C2637
C2607
C4082
C2606
B4008
R4061
R4060
C2605
C2604
C4083_1 C4078_1 C4051_1 C4052_1
C4013
R4050
R4049
R4046
C4008
CP2601
C2603
C4016
C4010
B4009
C4014
C4065
C4077
C4047
W806
R4051
C4018
C4017
C2608_1
C2634
W857
Q2601
R4044
C4066
C2648
R2616
C4001
1 53
C2638
R4052
R4056
B2601 R4048
C4090
C4019
R2615
W874
W873
C2636
C4002
D2601
C4020
IC4005
W832
R2618
C4003
B2602 R2654
R4064
R2647 R2617
C4089
Q2605
Q2602
C4046
Q2604
IC4001 R4059
R2624 C4088
R2623 C2640_1 R4008
C4040
C4004
Q2603
R2620 C2639
R2619
B4001 C4006
C4070_1
C4084_1 B4003 157 105
C4007
B4004
C4073 C4068_1
C4033
C4076 C4037
C8522
R4017
C4032
C4030
C4031
B4002 B4010
C4029
IC4002
R4001
C4096
C4027
C4028
W871
C4079
C4025 R4035
C4081
C4071_1
B4005
R4014 R4053
R4031
R4002
R4003
R4004
C4072
R4025
R4024
W802
R4058
W801
R4012 R4042
C4093
C4094
C8504
C8507
C8510
C4035
R4054
C4026
C4067_1
R4047
R4005
R4020
R4019
C4098
R4021
W831
X4001
R4026
L8502
L8503
L8504
R4027
R4018
W860
IC8502
C4038 R4045
Q8502
Q8503
Q8504
R4016 C8513_1
C8517_1 W872
R8518 R8519 R8520 C8519_1
W855
W877
W879
C8518
C8520 B8503 W878
B8502
F-1 F-2
F-4
C432_1 R430
J4201
Q3800
W836
W820
R3831
IC3800
W002
C439
R3833
R450_1
D402
C3823 C3822
R3800 D3822
B4201
D410 D3818
R423
R3805
R3804
D3806
C402
D3801
D3827 W802
D3819
R445 TP403
VR3800
R3825
W008
D3830
C431
C3811
FB401_1
CP803A
TU001
HS3800
D3807
Q3803
D413 L4202
TP402
D3820
R3822
W003
C430 W005
C4204
W006
R442
R3821
T3800
TP401
D3811
R453 C006
C3826 B3800
.
R3816
Q401
R410
R408
C3807
R3812 L001
MARKED
R3801 C3808
R406
R3826
W007
D3810
R3827
W838
W004
W001
D3809
R405
R404
- REPLACE
C401
FH3801
R4205
C3812
C3810
D3815
D3828
D3808
L401
D406 W828
R3829
C422 HS402
D408
D3816
47
01 D3802
FH3800 F3800
B401 R4
17
CP401
Q406
OF FIRE
3
42 C3815
D38
D3826 D3006
C3816
C429 W021
RISK
D3823
Q3006
Q3008
R456
IC3001
C418
D411
PH3801
TH3800_2
W226
T401
R419
L3801_1
W017
R3803
IC3005
CP101
Q3005
R3005
C3801
Q3009
W024
Q405
IC3002
C3006 PH3800
W013
W014
C417 CP3800
W035
W018
W025
D405 D3803
W009 W036
W020 D3005 C3827
W010 C3020 C3013 C3820 W037 W033
6
C421 S001Y R380
W011 W028 W038
02
S802Y
C434_1
R424
R4
W040
W029 W039
W826
W015 CP801
Q3004
C634
R3010
W059 W023
W031
R412
W012
W062
R614
PRINTED CIRCUIT BOARDS
R3006
W071
C3023_1
W041
R467
D3003
W914
CP802A
W051
W049
R3003
R804 W066
W079
W053
_1 C605
01 C3028
W060
J8
W055
D404
W089
D414
W065
SOLDER SIDE
W047
W088
W063
W050
R3007
R3009
R603
D409
W074
W073
W072
W078
W067
W077
W076
R612
D603
R3019
R613
D403
C3014
W843
CP802B
W057 W087
R622
R627 W046
IC401
W056
HS401_1
D802
W044 R616 C612 W085
C4214
Q805
S001X
C606
CP803B
D401
L602
TP024
TP022
C619
TP023
D801 S002Y
R411 W916 W045 C4206
W064
R413
S002X
R806_1
W080
Q804
W052 W061
W043 C603 W081
C4217
R803
R807
L801
R407
R805
C4230 W083
VR401
D803
CP8002
C604 W069
R418
Q806
R421 W084
C622
C4229
R416 R414 C626 C4232
C602 R4235
L4201
X601
R4234
C4231
W144
C405 C628 W141 C4203
W160 W149
CP302
C4234 C3012
R630 W158
C407 D416 W145 W148
R4240
W159
C624 W146
W091
W090
S802X
W107
W094
W832
W827
W113
W124 W125 W151
B301 C4227 C633
R4251
R4252
W112
W142
W126 W114
C313
W152
CP8001
W147
W139
W123
W143
CP301
W110
W118 W132
HS301 W813
L902
W109
D3007
W119 W133 W156
W121
W131 W150
C312
W803
W105
W135
W093 W096 W819
R3014
W837
R159
C922
W137
W138
W122 W128 C3025
D106
W111 C3005
W098
L904
L101
W103 W115 W130
W097
L3000
IC302
Q3003
HS3001
C3007
W140
W092 W108 C945 C920
W153
W170 W175 W120 W805
X101
W197 D3009
W863
W181 W179
C943 R125 C119
R303 W195 C3017 W218
IC101
C346 W182 C941 C410 D102 W224
R301 W219
W198 W214 W804
C921
W215
R912 W199
IC199
W814
R190
C925 W211
C347 W220
C926 W212
W174 R911
W216
W183 W812
C928 C103
C110 W209
C2205 W188
W184
D103
C931
W194
W193
W185 C907 W210
W169
W201
D101
W191
W202
W173
W171
W172
W203
W225
W200
W192
D107
W206
C328 D105
C936
W815
W844
W213
R346
R323
R101
C101
W834
W833
R909
C932
W217
W222
W208
R2225
W205
C2204
W207
C4275
W168
W165
C2201
W167
W166
W164
W190
W189
W221
R2201
R2202
W163
W180
D2201
W
R
W223
Y
OS2202
W825
R2226
SW2214
SW2217
SW2221
SW2219
SW2216
SW2218
SW2220
SW2215
W204
J2201
SW2223
SW2213
J2203
J2204
J2202
F-3
F-5
C3809
C4224
C3805
R4210
R4216
R4221
C4215
Q4201
C4205
R4242
R4241
C002
C001
C3806
W852
W850
R634
Q3007
Q602
Q3001
R420
C810
R816 C614 R4211
Q605
R808 R4212
R605
C4210
SOLDER SIDE
R615 R4213
C617
Q601
C608 R4202
C811 R617 R4223
R611 R607 R4208
R813 C620 C618 C607 C4225 C4212
R628 R610
C4222 C4226
IC4201
R4233
R809 R4230
R4201
R602
PRINTED CIRCUIT BOARDS
C809
R815 IC
1
33
60
R624 1
AV/CRT (CHIP MOUNTED PARTS)
C630
R625
49
C629
Q4203
C302 C4233
Q4212
C631
C3003 C303
C632
R4236
R302
R4237
C305
W849
C331
C3002
R145 R157
R141
R311
R142 C3004
C307 R109 C111 R144 R149
R106 R160
C944 C128 R140 R148 C129
R120 C127
Q101
R119
R114 R134
W857
C323 W856
Q302
R307
R305
W823
R122
R308
C306 R910
R132
R306
W842 C117
C104
R4227
R304 C108
IC902
C934 C935
R127
Q301
R147
C939 R913
R908
C4274
Q2201
R121
R123
C2203
C2202
R2215
R2220
R2214
R2218
R2219
R2221
S1005X
S1004X
S1001X
S1003X
S1002X
CP1
0 02
002
SW
SOLDER SIDE
S1004Y
S1005Y
00
SW2
F-7 F-8
A B C D E F G H
SLED_PWM
SPINDLE_PWM
SPDL_SENS
DAC_VIDEO_D
DAC_VIDEO_C
DAC_VIDEO_B
TRACK_DAC
FOCUS_DAC
RFA_SDEN
MIRR
RFA_DATA
RFA_SCLK
DEFECT
AAF_CE
10K ADCIN_5
10K ADCIN_6
10K ADCIN_7
AAF_TE
VBIASS1
VBIASS0
AAF_FE
LINK
FNN
FNP
AAF_PI
C4085 0.001 B
P.CON+3.3V
FROM/TO AUDIO/VIDEO
C4086
0.001 B
DAC_VIDEO_C
DAC_VIDEO_B
C4038 DAC_VIDEO_D
4.7K
4.7K
4.7K
4.7K
4.7K
100
100
C4088 ASDATA0
47K
0.01 B 0.01 B R4003 75 +-1% ABCLK
R4044
R4043
R4022
ALRCLK
DUPTD1 R4004 75 +-1%
C4089 AMCLK
R4049
R4052
R4046
R4050
R4051
R4057
R4056
R4017
DUPRD1 R4005 75 +-1% MD
0.01 B MC
DUPTD0 C4090
W832 ML
V_GND
DUPRD0 RESET
0.01 B W833 GND
P.CON+5V P.CON+3.3V
7 P.CON+A5V 7
DAC_VIDEO_A
W831
0.1 F
0.1 F
0.1 F
6.3V 47 KA
6.3V 47 KA
6.3V 47 KA
6.3V 47 KA
47 KA
P.CON+5V
0.1 F
0.1 F
0.1 F
AFE_GND
C4067_1
C4068_1
C4071_1
W857
C4069_1
C4070_1
0.1 F
0.1 F
GND
0.1 F
0.1 F
4.7K
4.7K
4.7K
4.7K
S_GND
D_GND
0.1 F
RFINN
0.1 F
6.3V
RFINP
C4072
C4073
C4074
C4075
C4076
3.3K
C4007
1K
C4004
C4001
C4005
C4006
B4002
R4037
R4038
R4039
R4036
FROM/TO RF AMP/DSP
C4002
C4003
FCM2012H-102T04 B4003
R4060
R4061
FPCSTRB
FPCCLK
FPCRX
B4001 FCM2012H-102T04
FPCTX
IRRCV
HOME
FCM2012H-102T04 B4004 SPDL_SENS
FROM/TO MEMORY TOUT_SW
+1.8V FCM2012H-102T04 TIN_SW
+3.3V B4005 RFA_SDEN
D_GND
NC
NC
NC
NC
RFA_DATA
R4018
FCM2012H-102T04
4.7K
P.CON+3.3V RFA_SCLK
3.3
3.3
4.3
0.7
3.3
3.3
3.3
3.3
3.3
2.9
2.9
1.8
1.5
0.7
1.1
1.7
1.6
1.8
1.7
1.6
1.5
1.7
3.3
1.2
1.2
3.3
0.8
3.3
0.9
1.2
1.2
1.1
3.3
1.2
1.1
R4045
4.7K
0
0
0
0
0
0
0
0
0
0
0
0
0
AAF_CE
6 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 AAF_FE 6
GNDPWM
VDDPWM
3.3
GNDDACDS
3.3
GNDDACPS
GNDDACBS2
DUPTD1
GNDDACP
VDDDACS
PWMCO(6)
PWMCO(5)
PWMCO(4)
PWMCO(3)
PWMCO(2)
PWMCO(1)
PWMCO(0)
PWMACT(1)
PWMACT(0)
GNDP
GNDC
GNDAFES
GNDAFERF
105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156
VDDP
VDDC
VDDAFES
VDDAFERF
RSET
HA0 SSCRXD DUPTD1 AAF_TE
DEFECT
VBIASS1
VBIASS0
RFINN
RFINP
52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
DACDRIVE(1)
DACDRIVE(0)
C/B/U
Y/R/V
ADCIN(0)
ADCIN(1)
ADCIN(2)
ADCIN(3)
ADCIN(4)
ADCIN(5)
ADCIN(6)
ADCIN(7)
5.1
ICGPCI/O(7)
ICGPCI/O(6)
HA1 3.3 DUPRD1 AAF_PI
NC MEMCS(1) DUPRD1
HA2 C4008 0.1 F 3.3 3.3 C4033 0.1 F VR_SEL
VDDP VDD-IP
HA3 HA15 3.0 3.3 DUPTD0 FNN
HA4 MEMAD(15) DUPTD0 FNP
HA16 3.0 5.0 DUPRD0
HA5 MEMAD(16) DUPRD0 VBIASS0
HA6 HA14 3.0 0 VBIASS1
MEMAD(14) GNDP
HA7 HA13 3.3 3.3 VR_SEL DEFECT
MEMAD(13) IDGPCI/O(3)
HA8 HA12 3.3 0 TRAY_OPEN C4032 0.001 B LINK
HA9 MEMAD(12) 208 SSCTXD 160 VDDDAC GPCI/O(34) TP4012 MIRR
HD15 0 3.3 TOUT_SW
HA10 MEMDA(15) ICGPCI/O(5) LDON
HA11 0.5 207 SSCCLK 159 CVBS/C 0 TRAY_CLOSE C4096 0.001 B
HA11 MEMAD(11) GPCI/O(33) TP4013 SMUTE
HA12 HD7 2.6 206 SPINDLEPULSE 158 CVBS/G/Y 0 TIN_SW TRACK_DAC
MEMDA(7) ICGPCI/O(4)
HA13 0 3.1 SMUTE FOCUS_DAC
HA14 GNDP 205 SLEDPULSE 157 GNDDACD GPCI/O(32) SPINDLE_PWM
HA10 0 3.3 C4027 0.1 F
100P
C4079
CH
HA15 MEMAD(10) VDDP SLED_PWM
HA16 HD14 1.9 0
MEMDA(14) GCLKA
5 HA17 0 0 27MHz 5
R4012
HA9 1
MEMAD(9) GCLKP
1M
HA18 0 0 R4042 X4001 P.CON+A5V
HD6
HA19 MEMDA(6) XO 100BT02701 C4035 22P CH R4016 P.CON+3.3V
HA8 0 1.8 68 RESET
HA20 MEMAD(8) VDDA C4028 0.1 F VCC+9V
HD0 HD13 2.1 3.3 100 P.CON+5V
MEMDA(13) RESET#
HD1 HD5 2.0 0 C4081 0.1 F ADCIN_7
MEMDA(5) GNDA
HD2 HA20 0 3.3 HOME HOME ADCIN_6
HD3 MEMAD(20) IDGPCI/O(2) ADCIN_5
C4010 0.1 F 3.3 3.3 TP4014 LDON
HD4 VDDP GPCI/O(31) M_GND
HD5 HD12 0.6 3.3
MEMDA(12) VID(0) D_GND
HD6 WR 3.3 3.3 DJTDO R4019 33 ML
MEMWR# VID(1) GND
HD7 2.6 0 R4020 33 D4001
HD4 DJTDI TP4004 MC DUPTD1
HD8 MEMDA(4) VID(2)
C4013 0.1 F 1.8 0 DJTMS R4021 33 TP4006 MD
HD9 VDDC VID(3) MCL4148
HD10 HD11 2.7 MPEG/MICON/DSP IC 0 ICETCK R4047 4.7K TP4005
MEMDA(11) V SW TP4008
HD11 HD3 2.9 3.3 ICETDO TP4007 LEVEL CONVERT
MEMDA(3) IC4001 D1 2 Q4004
HD12 HA19 0 3.3 ICETDI
6.3V 47 KA
MEMAD(19) ZR36762 D1 1 KTC3875S_Y_RTK
C4084_1
HD13 0 3.3 A_MUTE TP4009
HD14 GNDC VID(7) R4031 4.7K 3.3 3.3
4 HD10 0.5 3.3 TP4010 C4029 0.1 F I2CCLK 4
HD15 MEMDA(10) VDDP
MEMCS0 HA18 0 3.3 I2CDAT R4035 4.7K
R4011
4.7K
MEMAD(18) STBY-L
RD 0 0 3.3
WR GNDP GNDP FROM/TO REGLATOR
100P CH
0.6 3.3
C4036
HD2 I2CDAT
0.1 B
MEMDA(2) HSYNC
IC4002 AT24C04N-10SI-2.7
R4013
47K
HA17 0 1.6 C4030 0.1 F 3.2 3.2 0 3.3
MEMAD(17) VDDC 5 6 7 8
10P CH
HD9 0.6 3.3 I2CCLK
C4042
MEMDA(9) VSYNC
47P CH
SDA SCL WP VCC
C4043
2.7 0
CH
HA7
10P CH
SD_A0 MEMAD(7) GNDC L4002
C4098
HD1 2.7 3.3 R4024
C4093
100P CH
SD_A1 P.CON+3.3V
C4091
MEMDA(1) AIN
100P
C4037
0.6 3.3
0.1 F
SD_A2 HA6 4.7K C4031 0.01 B
EEPROM IC
MEMAD(6) VDDP-A2 W5T29X7.5X19
SD_A3 HD8 0.4 1.7 IAMCLK R4025 220 AMCLK
SD_A4 MEMDA(8) AMCLK
HA5 5.5 100 RAMDAT(14) 0 D_GND
SD_A5 MEMAD(5) GNDP-A2 GND NC NC NC
C4094
3.3 1.7 R4026 100 ABCLK
100P CH
C4014 0.1 F IABCLK
C4092
SD_A6 53 RAMADD(4) 101 GNDP 200/330mm
0.01 B
0.01 B
VDDP ABCLK 4 3 2 1
C4065
C4080
SD_A7 HD0 0.4 1.6 IALRCLK R4027 100 ALRCLK 0 0 0 0 CD4002 (CP8001)
MEMDA(0) 54 RAMADD(3) 102 RAMDAT(1) ALRCLK
SD_A8 HA4 3.3 0 CU2B2001
SD_A9 MEMAD(4) GPAI/O NC P.CON+5V
C4066
RD 0 55 RAMADD(5) 103 RAMDAT(15) 0 R4058 47 ASDATA0 GND 1
SD_A10 MEMRD# AOUT(0) REG+1.8V IC
1 B
3 SD_A11 HA3 0 0 ASDATA1 TP4015 IC4003 PQ070XZ01ZP GND 2 3
MEMAD(3) 56 RAMADD(2) 104 RAMDAT(0) AOUT(1)
SD_D0 HA2 0 0
RAMCS(0)# RAMBA(1)
RAMADD(11)
RAMDAAT(3)
3.2 0
RAMDAT(10)
RAMDAT(11)
RAMDAT(12)
RAMDAT(13)
SD_D4 HA0
RAMADD(6)
RAMADD(1)
RAMADD(7)
RAMADD(0)
RAMADD(8)
RAMADD(9)
RAMDAT(8)
RAMDAT(7)
RAMDAT(9)
RAMDAT(6)
RAMDAT(5)
RAMDAT(4)
RAMDAT(2)
RAMCS(1)#
NC
W805
MEMAD(0) ICGPCI/O(0) VCC+9V
RAMBA(0)
RAMRAS#
RAMCAS#
GNDPCLK
0 0
RAMDQM
VDDPCLK
SD_D5 P.CON+9V 6
RAMWE#
GNDC
GNDP
GNDP
GNDP
GNDC
VDDP
VDDC
VDDP
VDDP
VDDP
VDDC
VDDP
P.CON+5V 7
PCLK
510 +-1%
0
0
0
0
W4BRH3.5X6X1.0X2
0.9
0.3
1.0
1.0
3.3
1.0
0.2
0.2
1.8
1.9
0.2
3.3
3.1
0.5
3.1
0.2
3.2
3.3
3.2
1.6
3.3
2.1
1.3
0.8
0.8
3.3
1.7
1.3
0.5
0.9
1.8
1.4
0.5
3.3
2.0
0.4
1.5
0.8
1.2
1.5
P.CON+3.3V
C4097
0.01 B
SD_D11 W802 GND 10
R4033 R4032
SD_D12
W801 SPDIF-134 11
SD_D13 B4006 GND
SD_D14
6.3V 100 KA
0.1 F
6.3V 100 KA
100 KA
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
0.1 F
C4015
F
SD_D15 FCM2012H-102T04
C4078_1
C4083_1
C4011_1
47
47
39
C4077
6.3V 100 KA
F
RAMCS0# SPDIF
0.1
C4082
1K +-1%
2 RAMCS1# 2
C4009_1
0.1
R4034
C4012
TP4011
F
C4020
C4023
RAMRAS# 2
0.1
C4018
C4019
C4022
C4024
C4025
R4059
R4064
6.3V
RAMCAS#
0.1
SD_BA0 TP4003
RAMDQM
RAMWE#
RAMCLK
R4008
R4053 R4054
100
NC NC
1K
RAMRAS#
1K
RAMCAS#
RAMCS0#
RAMCS1#
PCB130
RAMDQM
SD_D10
SD_D11
SD_D12
SD_D13
SD_D14
SD_D15
RAMWE#
SD_A10
SD_A11
SD_D8
SD_D7
SD_D9
SD_D6
SD_D5
SD_D4
SD_D3
SD_D2
SD_D1
SD_D0
SD_A4
SD_A3
SD_A5
SD_A2
SD_A6
SD_A1
SD_A7
SD_A0
SD_A8
SD_A9
RAMCLK
SD_BA0
VMC319
BOOTSEL2 BOOTSEL1
1 1
NOTE:THE DC VOLTAGE EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
DIGITAL AUDIO SIGNAL(PB) DURING PLAYBACK.
A B C D E F G H
G-1 G-2
A B C D E F G H
48
A16 A15
1
SD_A2
SD_A3
SD_A4 C4064 3.3 1.0
7 HA14 7
47
VCCQ A14
2
SD_A5
SD_A6 0.1 F 64M SDRAM IC
SD_A7 0 0.8 HA13 IC4005 M12L64164A-7T
46
VSS A13
3
SD_A8
SD_A9 0 3.3
54
VSS VDD
1
SD_A10 HD15 0.7 1.5 HA12
45
DQ15 A12
4
SD_A11 SD_D15 1.2 1.5 SD_D0
53
DQ15 DQ0
2
SD_D0
SD_D1 1.9 2.5 0 3.3 C4050
HD7 HA11
44
52
DQ7 A11 VSSQ VDDQ
3
SD_D2
SD_D3 1.5 0.8 0.1 F
SD_D14 SD_D1
51
DQ14 DQ1
4
SD_D4 HD14 1.3 1.3 HA10
43
DQ14 A10
6
SD_D5 SD_D13 2.0 0.4 SD_D2
50
DQ13 DQ2
5
SD_D6
SD_D7 1.2 1.6 C4040 3.3 0
HD6 HA9
42
49
DQ6 A9 VDDQ VSSQ
6
SD_D8
SD_D9 0.1 F 0.4 0.5
SD_D12 SD_D3
48
DQ12 DQ3
7
SD_D10 HD13 0.6 1.5 HA8
41
DQ13 A8
8
6 SD_D11 SD_D11 0.5 0.9 SD_D4 6
47
DQ11 DQ4
8
SD_D12
0 C4045
SD_D13 HD5 0.7 HA19 0 3.3
40
46
DQ5 A19 VSSQ VDDQ
9
SD_D14
SD_D15 1.7 1.3 0.1 F
0 SD_D10 SD_D5
45
10
RAMCS0# 0.8 DQ10 DQ5
HD12 HA20
39
10
RAMCS1# DQ12 A20 0.8 0.8
SD_D9 SD_D6
44
11
RAMRAS# DQ9 DQ6
RAMCAS# 1.6 3.3 C4041 3.3 0
HD4 WR
38
11
43
12
SD_BA0 DQ4 WE# VDDQ VSSQ
RAMDQM 0.1 F 2.1 1.3
C4062 SD_D8 SD_D7
13
42
RAMWE# 3.3 0 DQ8 DQ7
RESET
37
12
RAMCLK VDD RP# 0 3.3 C4046
0.1 F
14
41
HA0 VSS VDD
0.1 C4039 0 0.1 F
HA1 HD11 1.6 0 RAMDQM
36
13
15
40
HA2 DQ11 VPP NC NC LDQM
HA3 0.1 F 0 3.2
0.1 RAMDQM RAMWE#
16
39
HA4 1.6 R4041 UDQM WE
HD3
35
14
HA5 DQ3 WP#
5 RAMCLK 1.5 3.2 RAMCAS# 5
17
38
HA6 4.7K CLK CAS
HA7 1.3 0 R4048 3.3 0.2
HD10 HA19 3 RAMRAS#
34
15
18
37
HA8 DQ10 A19 CKE RAS
HA9 47K 0 3.1 RAMCS1#
19
36
HA10 1.2 1.6 NC NC CS
HD2 HA18
33
16
HA11 DQ2 A18 0 0.5
SD_A11 SD_BA0
35
20
HA12 A11 BA0
HA13 HD9 1.4 0.7 HA17 SD_A9 0.2 3.1 RAMCS0#
32
17
34
21
HA14 DQ9 A17 A9 BA1
HA15 SD_A8 0.2 1.9 SD_A10
33
22
HA16 1.4 1.4 A8 A10/AP
HD1 HA7
31
18
HA17 DQ1 A7 1.0 0.2
SD_A7 SD_A0
32
23
HA18 A7 A0
HA19 HD8 0.9 1.6 HA6 SD_A6 1.0 0 SD_A1
30
19
31
24
HA20 DQ8 A6 A6 A1
HD0 SD_A5 1.0 0 SD_A2
30
25
HD1 1.6 1.6 A5 A2
HD0 HA5
29
20
HD2 DQ0 A5 0.9 0.3
SD_A4 SD_A3
29
26
4 HD3 A4 A3 4
HD4 2.6 1.3 0 3.3 C4047
RD HA4
28
21
28
27
HD5 DE# A4 VSS VDD
HD6 0.1 F
HD7 0 1.7 HA3
27
22
HD8 VSS A3
HD9
HD10 MEMCS0 W854 2.6 2.5 HA2
26
23
HD11 CE# A2
HD12
HD13 HA0 2.5 1.6 HA1
25
24
HD14 A0 A1
R4040
HD15
4.7K
MEMCS0 B4007
RD FCM2012H-102T04
WR
B4008
FCM2012H-102T04
6.3V 220 KA
3 P.CON+3.3V 3
6.3V 220 KA
6.3V 220 KA
C4063_1
C4052_1
C4051_1
0.01 B
C4095
B
C4099
0.01
D_GND
FROM AUDIO/VIDEO
RESET
2 2
PCB130
VMC319
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS
1 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER 1
DURING PLAYBACK.
A B C D E F G H
G-3 G-4
A B C D E F G H
VR_DVD
FNN
FNP
P.CON+5V
SPDL_SENS
VR_SEL
CD2601
VR_CD
2H0O1901 TOUT_SW
MOT_SPDL+ R2625
R2632
TIN_SW
4.7K
5 4.7K R2627 RFA_SDEN
R2626 R2631
R2619
RFA_DATA
R2621
MOT_SPDL- P.CON+5V
R2622
100
100
RFA_SCLK
R2624
5.2 0.7 7.3 5.2
4.7K
4.7K 1.5K 1M
4.7K
AAF_CE
F
FROM/TO LODER D0 5 6 7 8
C2626
C2632
VR DVD CTL R2620 AAF_FE
0.1
0.1
Q2603 G AAF_TE
+IN2 -IN2 OUT2 VCC
DUAL OP-AMP IC
CP2601
C2649
B
2SK3018 0.7 4.7K 0.5 AAF_PI
BA10358F-E2
IMSA-9631S-24Y901 D
R2629
S0 R2647 VR_SEL
1.5K
0.1
NC G
IC2602
TR- VR CD CTL FNN
24 T-
Q2604 0 4.7K D 0 TP12 TP11 FNP
TR+
12K +-1%
R2623
R2628
S
0.001 B
23 T+ 2SK3018 VR SEL CTL G 0.7 VBIASS0
22K
0.033 B
FO- 0 Q2605 FNN GND +IN1 -IN1 OUT1 VBIASS1
7 22 F- 4.7K 7
C2627
FO+ 2SK3018 S 0 4 3 2 1 DEFECT
21 F+ FNP LINK
R2630
0.001 B
DVDPD 0 5.2 4.1 4.1 MIRR
22K
C2628
20 MON(DVD) TP8
C2625 0.001 B
C2635 TP9 LDON
OPU_RF
19 NC(SW) NC
R2614
HOME
C2633
TP10
VR_DVD 0.001 B W806
0.001 B
18 VOL(DVD) 4 RF_GND
C2629
0.001 B
GND
RFAC
C2624
W807 D_GND
17 GND(DVD) D_GND
C2646_1
47 KA
DVDLD
0.1 F
C2647
16 LD(DVD)
6.3V
CDLD 1.5 0 3.1 3.1 4.3 4.3 5.1 2.4 2.6 3.5 3.5 2.3 0 0 0 0 B2605 P.CON+5V
15 LD(CD) RF_A5V
VR_CD 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P.CON+A5V
14 VOL(CD) TP15 FCM2012H-102T04 P.CON+3.3V
MEV
ATON
VNA
RFDC
ATOP
0.1 F
VPA
BYP
RX
RFAC
FNN
FNP
C2645
DIN
RFSIN
0 0
AIN
DIP
AIP
RF_GND RFA_SDEN
48
13 GND(CD) NC
1
CDPD R2611 TP16
12 MON(COM) 0 1.5 4.7K RFA_DATA
6.3V 47 KA
6.3V 47 KA
47
NC DVDRFN
C2644_1
SDATA
0.1 F
11 GND(NC) NC
C2642
C2643_1
R2612 TP17
OPU_RF C2603 R2310 R2312
W875
2.5 3.3
W882
10 RF 1 DVDRFP 4.7K RFA_SCLK
46
6 A2 SCLK
3
OPU_C 48 SDEN
R2613 B2604 6
9 C 0.0022 B TP18 5.6K 5.6K
0 3.3 FCM2012H-102T04
OPU_B C2604 4.7K
45
8 B B2 V33
4
OPU_A 0.0022 B B2603
7 A 2.5 4.2 C2616
C2605
44
OPU_D C2 LCP
5
6 D C2654 FCM2012H-102T04
0.0022 B 470P CH
OPU_F 2.5 4.1 0.01 B
5 F C2606 SMUTE
43
D2 LCN
6
OPU_E R2644 R2306
4 E 0.0022 B TRACK_DAC
3.7 0 R2643 2.2K
C2607 5.6K
42
3 VCC CP MNTR
R2309
7
FOCUS_DAC
R2314
5.6K
C2619
470
OPU_VREF 33P CH 1K
2 VREF 3.7 1.8 560P CH SPINDLE_PWM
C2634 AAF_CE
41
CN READ CHANNEL IC CE
R2318
5.6K
8
1 GND(PDIC) NC C2620 SLED_PWM
220P CH
TP19 IC2601
C2304
NC 0.1 F R2607
R2313
5.6K
OPU_D 2.7 1.7 0.0056 B AAF_FE ADCIN_7
40
D ZR36708TQC FE
9
C2648
TP20 1.2K C2621 C2305
ADCIN_5
FFC(P=1.0mm) 0.1 F OPU_C 2.7 1.8 R2608 0.0056 B AAF_TE
10
39
C TE 220P CH C2309 C2312 ADCIN_6
5 CD2602 P.CON+3.3V TP21 1.2K C2622 5
2.7 1.6 R2609 VCC+9V
2H080701 M_GND OPU_B 0.0056 B AAF_PI 0.001 B 0.001 B
11
38
B PI
C2623
C2659 100P CH
TP45
2.6 3.3
100P CH C2658
C2660
OPU_A 0.1 F
12
37
A V25
16 CD_A 33 LINK
R2334
R2605 R2610 5.1K +-1%
10K
W863
TP26
FROM/TO LODER
R2635
4.7K
W864
13
36
CD_D V125
100P CH
C2657
CP2602 C2618
C2617 TP38
R2324
2.7 0
1K
IMSA-9615S-08C-PP
14
35
CD_C TPH 0.1 B VBIASS1
R2301
MOT_SLED-
1K
0.1 B
R2319
27K
TP46
1 SLD- TP35
R2307
27K
MOT_SLED+ 2.7 3.3 DEFECT
15
34
2 SLD+ CD_B DFT
C2615 TP33 W862
DVDPD
DVDLD
MOT_SPDL- R2645
51K
MEVO
3 SP1-
CDPD
LDON
20K
CDLD
MIRR
MLPF
2.6 0
CD_E
0.1 F
CD_F
LINK
8.2K
51K
16
33
VNB
VPB
MIN
763WSA0023
4.7K
4.7K
20K
MOT_SPDL+
MP
MB
VC
4 SP1+ 1K R2646
R2649
HS2301
HOME
HS73
TP138
5 LIMIT SW 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
R2308
TP139
TP140
R2305
100 2.2K
R2316
R2321
R2322
R2326
R2327
6 GND 2.6 2.6 5.1 5.1 3.7 5.1 0.2 0.2 0 3.3 0 2.7 2.2 2.3 2.9 0.2 R2602 C2655
4 4
0.0068 B
220P CH
7 SP_FG NC
C2613
C2610
R2601 1.8M 0.01 B
8 +5V
27K +-1%
B
R2344
13K +-1%
4.7K
R2603
R2604
P.CON+9V
C2614
NC NC NC
0.1
0.033 B
C2612
TP27
TP28
TP34
TP29
TP30
TP31
TP25
TP37
TP36
0 0 3.3 2.5 2.5 2.5 2.6 5.0 1.6 0 2.5 2.5 2.6 2.5 2.5 3.0 2.5 1.2 1/2W
0.9 1.6
36 35 34 33 32 31 30 29 28 38 27 26 25 24 23 22 21 20 19 R2345
R2648
REG-OUT
MUTE
VCONT
VREF-OUT
S-GND
VIN4+
VIN3+
VIN2+
VIN1-SW
VIN4-
VIN3-
VIN2-
VIN1+B
REG-IN
VREF-IN
1.2 1/2W
VIN4
VIN3
VIN2
MOTOR DRIVE IC
R2337
13K
10K
6.3V 47 KA
OPU_VREF
C2608_1
0.1 F
LA6560
LDON
MIRR
IC2301
DVDPD
CDPD
C2609
C2611
OPU_F
OPU_E
R2330
RF_GND W808 SGND
1K
CP2603
VIN1+A
VIN1-A
VIN1-B
A2001WR2-3P
VCC2
VLD+
VD4+
VD3+
VD2+
VD1+
VCC1
VLD-
VD4-
VD3-
VD2-
VD1-
R2652
VIN1
FWD
REV
CLOSE TIN_SW
1
TP141
TP24
100
2 GND(D)
P.CON+A5V
R2653 1 2 3 4 5 6 7 8 9 37 10 11 12 13 14 15 16 17 18
3 3 OPEN TOUT_SW 3
0
0 0 9.1 0.2 0.2 4.0 4.3 4.3 4.1 5.3 3.1 4.2 4.2 9.1 2.5 0 2.5 2.5
100 TP043 TP39 R2328
R2650
R2651 4.7K
NC NC
TP64
TP65
TP69
TP68
TP56
TP55
TP66
TP67
R2325 4.7K
W861
4.7K
R2615 6.8K
C2301
F
Q2601 4.5
R2331
C2310
R2616
C2306
F
2SA1036K
470
3.9
0.1
C2311
B
0.1
B2601 1K
0.1
FCM2012H-102T04 1.0
DVDLD
C2640_1
D2601 TP40
F
F
C2636
C2638
0.1
C2641_1
2
0.1 B
F
C2303 0.1 B
C2637
C2639
2 6.3V 100 KA 2
0.1
0.1
C2308
B2602 R2304 2.2
CDLD 0.1 B
FCM2012H-102T04 1.0
R2617
CD LD CTL
3.9 1K
Q2602
4.5
MOT_SPDL+
MOT_SLED+
MOT_SPDL-
MOT_SLED-
2SA1036K R2618
TP42
R2654 18
TP41
TR+
FO+
TR-
PCB130
FO-
18 VMC319
D_GND
1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS 1
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
A B C D E F G H
G-5 G-6
A B C D E F G H
B V R Y V
C U B C U
R8518
R8519
R8520
470
470
470
D C CVBS CVBS CVBS
R8507
R8508
R8509
470
470
470
FROM/TO MPEG/MICON
150P CH
150P CH
C8504
C8506
KTA1504S_Y_RTK
1uH 0305
VIDEO_BUFFER
Q8503 1.3
C8508 KTA1504S_Y_RTK
DAC_VIDEO_B
6 RESET 12P CH 0.6
0 6
150P CH
150P CH
MC
L8503
C8507
C8509
MD
ML
1uH 0305
AMCLK
ABCLK 1.3
C8511 0.5
ALRCLK DAC_VIDEO_D
ASDATA0 12P CH VIDEO_BUFFER
0
150P CH
150P CH
L8504 Q8504
C8510
C8512
KTA1504S_Y_RTK
1uH 0305
GND
W874
5 5
W873
W860
W855
D_GND
6.3V 100 KA
6.3V 22 KA
C8518
0.1 F
C8519_1
TO MEMORY
C8520
C8517_1
F
0.1
RESET
4 4
R8514
100K
100K
R8515
FFC(1.25P)
B8503
CD8501
FCM2012H-102T04 B8502 2H0C1001
FCM2012H-102T04 C8514_1
W878
(CP8002) CP8502
IMSA-9604S-12Z13
C8513_1
W872 DAC_D_DVD_VIDEO
CVBS 1
50V 4.7 KA 7 GND 2
DAC_C[C]_VIDEO
C(CVBS) 3
GND 4
DAC_B[Y]_VIDEO
3 Y 5 3
GND 6
L_AUDIO
AUDIO-L 7
2.4 2.5 4.9 3.3 0 1.6 1.1 1.6
8 7 6 5 4 3 2 1 GND 8
IC8502 PCM1742KEG/2K
DGND
VOUTR
VDD
VOUTL
R_AUDIO
LRCK
DATA
VCC
BCK
AUDIO-R 9
ZERO W871
ZERO 10
ZEROR/ZEROA
RESET
STEREO DAC IC
DVD RESET 11
ZEROL/NA
GND 12
VCOM
AGND
SCK
MD
MC
ML
9 10 11 12 13 14 15 16
0 2.4 3.3 0 0 0 3.3 1.7
NC
C8522
0.001 B
2 2
C8521_1
16V 10 KA
ASDATA0
ALRCLK
AMCLK
ABCLK
ZERO
MD
ML
PCB130
MC
VMC319
PLAYBACK COLOR SIGNAL R.SIGNAL + COMPONENT SIGNAL(U) NOTE:THE DC VOLTAGE EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
1 PLAYBACK LUMINANCE SIGNAL MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1
B.SIGNAL + COMPONENT SIGNAL(V) DURING PLAYBACK.
PLAYBACK VIDEO SIGNAL
AUDIO SIGNAL(PB)
DIGITAL AUDIO SIGNAL(PB)
A B C D E F G H
G-7 G-8
A B C D E F G H
FROM POWER
UNREG+12V
UNREG+8V
UNREG+5V
GND
FROM/TO SOUND AMP
5V REG IC
IC3001 KIA7805API
7 GND 7
TO STEREO
UNREG+12V 3.3V OUT
L3000 Q3003
IN GND OUT KTC4369 P.CON+9V
1 2 3 5.0 P.CON+5V
10uH TSL0808
1000 YK
3.3
6.3V 330 YK
8.1 0 5.0 4.0 AT+5.6V
C3017
C3025
DRIVER P.CON+12V
DRIVER
Q3004
Q3006 GND
KTA1281_Y
16V
KTC3203_Y
D3008 7.4 8.2 R3014
100 YK
DRIVER R3006 8.6
W852
8.6 Q3010
C3015
6 6
1K 1/4W
W857
KTA1281_Y 10K 1/4W
R3004
12.1 11.2
6.3V
C3005
16V 470 YK
KA
1SS133
11.8
D3003
9V REG IC
C3026
IC3005 KIA7809API R3010 R3018
50V 2.2
FROM/TO VIF/SIF/CHROMA
1M 1/4W 1K 1/4W
50V 1 YK
8.5VREG
16V 470 YK
MTZJ3.6B
4.0
D3009
C3007
C3021
HS3001 R3019
SW DVD_H
100 1/4W 763WAA0157
R3001
Q3007 0 AT5.7VREG
2.2K 1/4W
IN GND OUT KTC3875S_Y_RTK 0 DVD_Y
1 2 3 DVD_C
12.3 0 9.1 DRIVER
D3006
Q3008
5 L3001 KTC3203_Y
P.CON+5V 5
1N4005-EIC
P.CON+9V
10uH 7.4 5.5 UNREG+12V
6.3V 100 YK
C3013
TSL0808 6.1 GND
C3001
TO DEFLECTION
100 1/4W
16V 10 KA
C3028
FROM/TO REGULATOR2 C3012 16V 1000 YK
R3009
P.CON+12V
CP8001 (CD8505)
16V 470 YK
A2001WV2-11P P.CON+5V
1 GND C3002 W819 DRIVER GND
TX AT5.7VREG
Q3005
2 GND 470P CH KTC3209_Y
3 TX 11.9 9.0
W803 P.CON+9V
RX FROM/TO MICON/TUNER
4 RX
DRIVER
5 GND(M) Q3000 9.6
4 DVD_H 4
KTA1281_Y
470P CH
6 P.CON+9V
16V 100 YK
C3004
C3030
7 P.CON+5V
DVD_RESET
8 P.CON+3.3V R3002 RX
12.8
C3003
100 1/4W
9 P.CON+3.3V TX
1K 1/4W
10K 1/4W
KA
R3003
C3023_1
R3007
10 GND P.CON+5V
0.1
SPDIF-134 SW
16V 10
11 SPDIF AT+5.6V
12.8 Q3001
P.CON+5V_A DTC114EKA GND
5.1
S001X S001Y 0
C3014 8.5VREG
3 6.3V 100 YK 3
5V REG IC POWER_ON_H
FROM/TO AUDIO/VIDEO IC3002 KIA7805API
D3007
CP8002 (CP8502) TO IN/OUT
IMSA-9604S-12Z14
MTZJ5.6B AT+5.6V
1 GND
DVD_RESET P.CON+9V
2 DVD RESET DRIVER
ZERO IN GND OUT P.CON+5V
3 ZERO Q3009
DVD_A_OUT_R KTC3209_Y 1 2 3 P.CON+12V
4 AUDIO-R
7.4 D3005 8.1 4.9
0 P.CON+5V_A
5 GND
DVD_A_OUT_L 9.01N4005-EIC SPDIF-134
6 AUDIO-L
9.6 DVD_A_OUT_L
7 GND
DVD_Y DVD_A_OUT_R
8 Y(G)
R3005 ZERO
2 9 GND 2
DVD_C DVD_VIDEO_A
10 C(CVBS)
KA
470 YK
W850
100 1/4W
C3006
GND
11 GND
C3020
50V 2.2
12 CVBS
6.3V
DVD_VIDEO_A
PCB250
TMB555
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: DIGITAL TRANSISTOR DIGITAL AUDIO SIGNAL(PB)
1 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE 1
DURING PLAYBACK. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES PLAYBACK LUMINANCE SIGNAL
DANS LA NOMENCLATURE DES PIECES PLAYBACK COLOR SIGNAL
PLAYBACK VIDEO SIGNAL
AUDIO SIGNAL(PB)
A B C D E F G H
G-9 G-10
A B C D E F G H
115-V-K015AR_B
8 8
TU001
19
OUT
OUT
12 AFT OUT
14 SIF OUT
20
10 CLOCK
16 IF OUT
AUDIO
17 VIDEO
11 DATA
+B
15 BT
FROM/TO IN/OUT
13
9
1
8
18 21
SCL
NC NC NC NC NC NC NC NC NC NC
SDA
W828
100 1/4W
I2C_OFF
100uH 9A06B
R004
F
REMOCON
C001
L001
KEY_A
0.1
D106
100 YK
7 R119 7
1/4W
KEY_B
C006
TUNER_AUDIO
TUNER_VIDEO
R003
POWER_FAIL
5.2 10K MTZJ12B POWER_ON_H
0.1 B
P.CON+5V
SW
C002
100
6.3V
Q101
+30V
4.1
SDA
RESET IC KTA1504S_Y_RTK
SCL
AFT
IC103 4.7
SDA
PST3231NR
SCL
SWD_V_OUT
NC NC
0.2 0.3
5 4
REMOCON
NC NC
270P CH
R123
W812
W814
10K
W856
C111
R134
1K
R148
R149
R157
R125
4.7K
4.7K
4.7K
OUT IN GND
0.1 B
D102 MTZJ5.6B
4.7K 1/4W
C109
FROM/TO VIF/SIF/CHROMA
1 2 3
R110
4.7K
R115
4.7K
6 5.2 5.2 0 R140 6
0.01 B
X101 OSD_Y
R144
C128
W805
CSTLS16M0X53-A02 100
D101 OSD_B
R141
2.7K
3 1 OSD_G
1SS133 R145
2.7K
OSD_R
10K 1/4W
L101
2.7K
SDA
MTZJ5.6B
1SS133
W863
D107
R101
R103
22 23 25 56uH
10K
D103
SCL
0.022 B
0.022 B
C107
C108
24
W804
SYNC_VIDEO
C124
26 H_CONTROL
0.1 F
PROTECT
KA
5.2 2.6 2.9 0 3.9 4.3 0.2 5.1 4.7 5.2 2.4 2.1 0 0 5.2 5.0 4.2 0 0 0 0
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 POWER_ON_H
0.01 B
(REMOCON)REMORT
C102
C101
OVDD(OVSS)
OVCC(OVDD)
33
VDD
(FM CLK)
VVSS
SDA
H-SYNC
SD
RESET
V-SYNC
OSD G
OSD R
POWER FAIL
TUNER_VIDEO
(FM DATA)
SCL
OSG B
TEST
X OUT
OSD Y/BLK
IC101 OEC6079A
VIDEO IN 1
X IN
VIDEO IN 2
5 5
10K 1/4W
SWD_V_OUT
6.3V
R190
0.1 B
C104
W837
HD
V-BUFFER
UART_START_BIT
UART_CLK_OUT
Q105
UART_CLK_IN
FROM DEFLECTION
H_CONTROL
(FM POWER)
KTC3875S_Y_RTK
X-RAY TEST
C103
PROTECT
R159
X-RAY IN
TV MUTE
POWER
TV/DVD
VD
MICON IC
KEY1
KEY2
6.3V 220 YK 0 33K 1/4W
VSS
AFT
0 X-RAY
RX
TX
+30V
0.0082 B
33P CH
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
C127
C129
0 0 0 5.2 0 3.2 5.1 0 5.2 3.7 3.7 5.2 5.2 0 0 2.3 5.2 5.2 4.1 0 5.2
R160
2.2K
NC
FROM POWER
POWER_FAIL
R113
4.7K
R126
R132
4.7K
4 GND 4
10K
1SS133
R122
R106
R109
10K
R120
4.7K
D105
4.7K
4.7K
R127
2.2K
R142
4.7K
FROM/TO REGULATOR
R114
4.7K
4.7K
R121
POWER_ON_H
H_CONTROL
DVD_RESET
DVD_H
POWER_ON_H
DVD_RESET
RX
PROTECT
VOL_PWM
A_MUTE
I2C_OFF
DVD_H
TX
KEY_A
KEY_B
AFT
RX
TX
P.CON+5V
3 AT+5.6V 3
GND
SDA
SCL
0.001 B
16V 10 KA
C106
C110
POWER_ON_H
A_MUTE
6.3V 100 YK
SCL
0.01 B
C119
C117
R147
SDA
100
VOL_PWM
R143
100
FROM/TO STEREO
2 TUNER_AUDIO 2
4.0 4.0 0 5.2
SCL
IC199 S-24C04BDP-LA
5 6 7 8
MODE
SDA
VCC
SCL
SDA
MEMORY IC
VSS
E2
E1
E0
4 3 2 1
PCB250
0 0 0 0 TMB555
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE LUMINANCE SIGNAL TUNER AUDIO SIGNAL
1
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE B.SIGNAL
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY TUNER VIDEO SIGNAL
DANS LA NOMENCLATURE DES PIECES G.SIGNAL PLAYBACK VIDEO SIGNAL
R.SIGNAL
A B C D E F G H
G-11 G-12
A B C D E F G H
P.CON+5V
DVD_C
SYNC_VIDEO
FRONT_VIDEO
POWER_ON_H
P.CON+5V_B
FROM/TO REGULATOR
DVD_Y
9A06B
100uH
L602
DVD_C
7 UNREG+12V 7
P.CON+5V S002X
GND
C4227
3.579545MHz
220 YK
100CT3R505
P.CON+9V SWD_V_OUT
X601
0.047 B
R626
22K
AT5.7VREG
C624
C627
0.1 B
50V 1 KA
C625
8.5VREG
6.3V
C632
0.1 B
R625 28
W849
TO DEFLECTION 22K
0.1 B
1 KA
C631
50V 1 KA
R624
680K
C626
8P CH
CH
C633
C630
C629
V.OUT
8P
50V
ACL
AFC
C621
B
0.1
6 H.OUT 6
CHROMA IC
IC601 NC NC
NC 0 NC 0 NC 0 5.2 0 5.2 2.5 2.5 4.5 3.9 0 3.4 5.0 3.0 3.5 2.6 C628 50V 0.47 KA
LA76319M-MPB-E
FROM IN/OUT
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
FRONT_VIDEO
49
32
NC NC
0
SWD_VIDEO 0
SCL W827
REG
50
31
5.2 SW 0
W832 C622 R622
SDA CLMP DVD_Y
51
30
5.2 VXD APC1 FSC 2.5 50V 1 KA 390 1/4W
52
29
NC VIDEO
0 CLMP 2.5
SW TINT C601
NC
53
28
5.2 AUDIO HOR 0
5 0.1 B 5
W809
R630 SW AF VCO
OSD_Y BPF YC SN ACC CEMO
54
27
SW X-RAY
1K 1/4W 5.2 0
1/256 R619
OSD_B
55
26
BUS CL BS
3.4 V/Y RGB COLOP 1.7
TRAP 4.7K +-1% 34
SW SHARP SG MATRIX CLAMP HOR R618
OSD_G AFC
56
25
C/D
3.4 5.9 220 1/4W 33
DC REST CONTRAST SYNC FBP
OSD_R H.OUT
57
24
LPF ATT BRIGHT SEP AFC1 NC
3.4 0 C618
100P CH
R617
C620
R616
2.2K
58
23
NC VER AFC2 0.015 B
680 1/4W
0 OSD OSD SEP 1.0
100 1/4W C619 R615
CONTRAST SW
R627
HD
59
22
5.0 VER PHASE 2.7 50V 1 KA 4.3K
C/D SHIFTER R613
ORIVE/OUT-OFF P.CON+9V
60
21
NC
0 VER HOR HOR 5.2 100 1/2W SW
RAMP VCC OUT Q601
4 4
61
20
NC CLMP
ABL/ACL 0 KTC3875S_Y_RTK
1/4W
0 2.4
H_CONTROL
0.33 B
R614
C617
62
19
C613
NC REG-SW 5.0 5.0
2.9
2.7K
0.1
0
63 4.4
18
NC RST 5V/8V-REG
3.0 4.3
R628
0
16V 100 YK
10K
9.0 SW
0.33 B
C614
64
17
NC Q605
C612
0 DTA114EKA
0
P.CON+5V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
0.47 MMTS
1/4W
0 0 0 5.0 6.0 8.6 2.6 0 2.8 3.4 8.6 0 7.9 3.7 3.5 3.5
C611
R612
NC NC NC
100
100
NC NC
100
100
R609
R610
R611
50V 1 KA
0.1 B
C604
C607
3 FROM/TO MICON/TUNER 3
HD
SW
32
POWER_ON_H Q602
V.OUT
KTC3875S_Y_RTK
SWD_V_OUT
0 R608
TUNER_VIDEO R634 P.CON+5V_B
L601
6.8K P.CON+9V
PROTECT 4.7K 6.0
330 1/2W
R605 D603
ACL
OSD_B
27K 1N4005-EIC TUNER_VIDEO
OSD_G
UNREG+12V
OSD_R
AT5.7VREG
SDA
KA
27
16V 220 YK
TO CRT
50V 1 KA
SYNC_VIDEO
0.1 B
C605
R602
C602
C603
C606
C609
R607
10K
15K
C608
H_CONTROL (CP802B) CP802A
50V 1
C634
B2013H02-6P
30 29 31
50V 1 KA CLAMP 1
GND 2
G.OUT 3
R.OUT 4
B.OUT 5 PCB250
TMB555
CLAMP_OFF 6
1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: DIGITAL TRANSISTOR PLAYBACK LUMINANCE SIGNAL TUNER VIDEO SIGNAL 1
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PLAYBACK COLOR SIGNAL PLAYBACK VIDEO SIGNAL
B.SIGNAL
G.SIGNAL
R.SIGNAL
A B C D E F G H
G-13 G-14
A B C D E F G H
SOUND_AMP IC
IC302 AN7522N
7 7
+ - L R - +
1 2 3 4 5 6 7 8 9 10 11 12
8.0 4.6 0 4.6 4.5 1.4 0 1.4 2.0 4.4 0 4.4
R311 C307 C348
MHE
B
0.1 B
C331
C313
2200
FROM/TO SPEAKER
HS301
763WAA0200 CP301 CD301 L CH
6 6
25V
SPEAKER
TID-X02P-M1 CU12414A
SP OUT L+ 1 1 SP351
SP OUT L- 2 2 SG04D11BNA
8 OHM
R CH
SPEAKER
FROM POWER
SP OUT R+ 1 1 SP352
B301
SOUND+B SP OUT R- 2 2 SG04D11BNA
W4BRH3.5X6X1.0 8 OHM
R307
4.7K
SOUND_GND CP302 CD302
50V 22 YK
470P CH
470P CH
TID-X02P-M1 CU12414A
C312
C303
35 36
C302
0.1 B
C323
FROM/TO REGULATOR FROM/TO IN/OUT
5 W813 5
GND SOUND_GND
KA
50V 4.7
SOUND_L+
C328
1/4W
0 SOUND_R+
R346
R326 0 SP_OUT_L
MUTE
4.7K
100 Q301 SP_OUT_R
2.0 KTC3875S_Y_RTK
47K 1/4W
R323
470P CH
470P CH
FROM MICON/TUNER
C304
C305
R302
POWER_ON_H
68K
A_MUTE
50V 2.2 KA
2.2 KA
VOL_PWM
C347
C346
4 4
50V
1K
R308
1K
R310
0.001 B
C306
820
R304
C310
820
R306
0.001
R301
FROM STEREO
5.1
R309 BUFFER 2.2K 1/4W
A_OUT_L Q305
1K 2.2 KTC3875S_Y_RTK
P.CON+12_A
3 12.0 R303 3
5.1 2.2K 1/4W
R305 2.2 BUFFER
A_OUT_R Q302
1K KTC3875S_Y_RTK
12.0
2 2
PCB250
TMB555
A B C D E F G H
G-15 G-16
A B C D E F G H
LTL-1CHEE-002A
AT+5.6V
8 (AV PCB) 8
D2201
OS2202
PIC-37243SR
1 Vout
220 1/4W
R2202
R2201
2 B+
100 1/4W
6.3V 47 KA
3 GND
C2204
5.2
5.1
POWER_ON_H SW
Q2201
0 DTC124EKA
POWER ON/OFF
820 1K 1.5K 2.7K 5.6K
OPEN/CLOSE
7 7
SW2213
SKIP REW
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
SW2215
SW2217
SW2219
SW2221
SW2223
SKIP FF
STOP
PLAY
REMOCON
TO STEREO
A_O_L
EVQ21505R
EVQ21505R
EVQ21505R
EVQ21505R
VOL DOWN
AT+5.6V
CH DOWN
A_O_R
SW2214
SW2216
SW2218
SW2220
VOL UP
CH UP
SOUND_GND
DVD_AUDIO_L KEY_A
DVD_AUDIO_R
R2215 R2217 R2219
KEY_B
W825
FRONT_A_IN_L
FRONT_A_IN_R 820 1K 1.5K
FRONT_A_IN_R
L4202 FRONT_A_IN_L
R4227
FRONT_VIDEO
6 100uH 0305 75 6
R4241
1.5K
470P CH
TO VIF/SIF CHROMA
J2203 HTJ-032-05AW
J2204 HTJ-032-05AR
SP_OUT_R
C2202
470P CH
C2201 100 1/4W
SP_OUT_L 16V 47 YK
470P CH
1.2 R4216 C4215 B4201
R2225
C2203
1 1 1
0.022 B
C4266
2
1
E E E
C4205
H
68 0.1 B
E
W5RH3.5X5X1.0
YK
C4224
470P CH
C4274
3.3K
100K
R4221
C4275
W820
470P B
220
R4210
P.CON+5V_A
R2226
P.CON+5V
5 5
SPDIF-134
AT+5.6V L4201
7
6
2
3
4
5
1
P.CON+12V
DVD_A_OUT_L 100uH 0305
R4243
S802X S802Y
DVD_A_OUT_R
10K
0
MUTE DET
ZERO Q4203
2.9 DTC144EKA HEADPHONE_JACK
P.CON+9V R4209
0
J2201
GND
16V 100 YK
220P CH
4.7K MSJ-2000
DVD_VIDEO_A
C4233
C4203
4 4
TEST POINT
P.CON+9V
CP101
KA
DVD_AUDIO_L
DVD_AUDIO_R
A2001WV2-9P
C4220 R4229
C4229
50V 2.2
16V 100 YK
R4230
KEY_A SDA
I2C_SDA 3
1K
AUDIO_OUT_R 7
C4216
IC4201 NJM4580M(TE1)
1/4W DTA143EKA
5.2 39
-
R4251
AMP IC
C4206 MUTE SW
R4238
R4201 R4211 +
DVD_A_OUT_L
3.3K
FROM/TO SOUND AMP 0 Q4212
100
5 6 7 8 DTC124EKA
5.2 5.2 5.2 10.4 1K 0
C4212
SP_OUT_L 0
C4232 38
1K 1/4W
SP_OUT_R R4235
R4218
SOUND_GND C4207
R4202 R4212 16V 22 KA 100 1/4W
R4232
100 1/4W
1K 1/4W
DVD_A_OUT_R
10K
C4222
R4240
R4237 10K R4252
R4213 R4223
KA
1K
R4236
2 Q4211 2
100P CH
C4234
0 KTC3875
10V 33 KA
1K 1/4W
C4225
50V 4.7
S_Y_RTK
C4214
KA
C4210
C4230
0
50V 2.2
R4219
10K
12K
PCB250
TMB555
AUDIO SIGNAL
CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR AUDIO SIGNAL(PB)
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS ATTENTION:LES PIECES REPAREES PAR UN ETANT CAUTION:SINCE THESE PARTS MARKED BY ARE
1 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES TUNER AUDIO SIGNAL 1
DURING PLAYBACK. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY
DANS LA NOMENCLATURE DES PIECES DIGITAL AUDIO SIGNAL(PB)
TUNER VIDEO SIGNAL
PLAYBACK VIDEO SIGNAL
A B C D E F G H
G-17 G-18
A B C D E F G H
7 7
W833
W834
L904
16V 100 YK
100uH
0.1 B
C944
C945
FROM/TO MICON/TUNER
40
6 TUNER_AUDIO 6
R911
SCL
100 1/4W R912
SDA
100 1/4W
100 1/4W
R909
TO SOUND AMP
41 42
A_OUT_L
A_OUT_R
W844
W815
P.CON+12_A
R908
5 270 5
C922
50V 2.2 KA
50V 2.2 KA
C920
50V 10 YK
0.047 B
2.7M
C907
R913
C933
FROM IN/OUT
W823
0.1 B
W842
A_O_R
C938
0.1 B
C935
A_O_L
DVD_AUDIO_L
2.2 2.2 2.2 2.2 NC 0 4.2 4.4 0 3.7 3.4 2.2 DVD_AUDIO_R
3.4
24 23 22 21 20 19 18 17 16 15 14 13 FRONT_A_IN_R
GND
AGC OUT SW DAC ZAP IIC Decoder St.PLL Det VCA Det FRONT_A_IN_L
Pilot Input SAP
SOUND DECORDER IC
AN5829S
4 Switch L-R Filter L-R Demod Cancel 4
Matrix De-Emph (L-R)/SAP Pilot Filter Filter Filter
75us L+R Filter L+R Demod Stereo Noise SAP
Filter
Cancel SAPout Demod
Offset fH.2fH Trap Filter Filter Filter SAP
Expand Wide Band Spectral
Cancel Wide Band
IC902
0.1 B
C939
50V 2.2 KA
50V 2.2 KA
100uH 0305
50V 4.7 KA
0.022 B
C941
C943
0.1 B
0.1 B
C937
L902
C929
C934
3 3
C926
330 YK
KA
FROM REGULATOR
50V 0.33 KA
50V 4.7 KA
50V 4.7 KA
16V 10 KA
C932
C936
C931
220K
50V 3.3
R910
C921
C925
C928
P.CON+12V
6.3V
P.CON+5V
GND
2 2
PCB250
TMB555
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED TUNER AUDIO SIGNAL
1 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST 1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
AUDIO SIGNAL
A B C D E F G H
G-19 G-20
A B C D E F G H
PUMP UP
Vcc GND
1 2 3 4 5 6 7
3.9 25.5 1.3 0 12.9 24.8 3.9
W843
C406
35V 100 YK
7 7
11E1-EIC
D401
TO DY
680 1/2W
R421
CP401
43 A1561WV2-A5P
5
560 1/2W
560 1/2W
4
R417
METAL
R419
W826
VR401
FROM/TO VIF/SIF/CHROMA 3
2.2K
R413 R416 NC 2
R412
V.OUT 1
3.3K 1/4W 1.8K 1/4W 56K 1/4W
ACL
R420
MTZJ30B
8.2K +-1%
AFC
D403
R414
2.2K
25V 2200 YK
VD
1 1/2W
R411
6 6
R467
C407
H.OUT
1.2K 1/2W
R424
R407
MTZJ30B
3.3K 1/4W
MKT
C405
D404
C434_1
0.22
2.2 1/2W
HS401_1
R418
FROM REGULATOR 763WSA0013
100V
C431 V801
W914 A34AGT13X98(DL)
GND
P.CON+5V R401 250V 22 YK
D406 D405 R402
500V 0.001 B
1N4937
9
D413
330 2W 1SS133 220 1W
C430
W916 1SS133
10
C422
11 B
C403
VD 5 7 1
4.7mH
L401
+30V
0909
C423
MTZJ33B
D408
68 1/2W
FB401_1 2 1
R447
FNI-14B001 CD805 (CP801)
272.0 COL SM1098-009-1A
56K 1/2W
1 HV
W841
R405
TO CRT
56K 1/2W
110.4
ETH09K14BZ 6
44 247.6 H.OUTPUT
4 FROM POWER 31.0 0 S 4
C428
Q406
MMTS
3 4 B+ FOCUS
0
470 1/2W 100V 0.01
0.2 0 11
W5RH3.5X5X1.0
+B 0 1 6 0 AFC
H-DRIVE 22.3 9 ABL 0 SCREEN
1.3 C429 7
Q405
B401
100 1/4W
50V 22 YK
UNREG+12V
0 KTC3227_Y 0 GND HEATER 0
R460
HS402
R456
C418
500V 0.0022 B 8 10
763WSA0017
S002Y -0.2 2.7
D411 E12
GND NC 4 5 NC
1N4937 0 E25
R450_1 GND
C421
5.6 1W TO CRT
MTZJ5.1B
D416
1N4937
3 3
D402
B2013H02-4P
0 22K 1/4W 1N4005-EIC 180V
CURRENT DET. 180V 4
135.0 C402
Q401 NC 3
KA
+-1%
2SA1624
TP402 TP403 100V 22 YK
R444
16V 10
HEATER
HEATER 1
5.6K
250V 10 YK
R442
R406 D409 R445
MKT
1SS133 22K M +-1% 15K 1/4W
5.6K 1/4W
47K 1/4W
MTZJ6.8B
D410
33K 1/2W
R410
C439
C432_1
R430
100V 0.47
R408
TP401 500V 56P SL
0.82 2W
R423
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. DEFLECTION SIGNAL
1 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP ATTENTION:LES PIECES REPAREES PAR UN ETANT CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DANGEREUSES AN POINT DE VUE SECURITE
IS NON POLAR ONE. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-21 G-22
A B C D E F G H
R801
R809
R808
4.7K
4.7K
4.7K
7 FROM DEFLECTION 7
CP803B (CP803A)
B2013H02-4P
1 HEATER
1SS133
1SS133
1SS133
D802
D803
2 GND
D801
3 NC
4 180V
390P CH
FROM/TO DEFLECTION
390P CH
470P CH
C811
C810
R813
R816
R815
C809
270
270
270
CP801 (CD805)
A2361WV2-2P
1 GND
6 2 GND 6
2.6 120.0 2.5 122.0 2.7 115.0
2.7K 1/4W
R804
1/4W
R806_1
1/4W
R802_1
5 5
2.7K
56uH
L801
2.7K
TP022
TP023
TP024
12K 2W
12K 2W
12K 2W
R807
R803
R805
4 4
FOCUS
SCREEN
SCREEN
CP806_1
6.4
9
8
2KV 0.001 B
3 3
C802
0
F
6
0
1
5
0
4
3
BL001
2 HPN-01 2
BT001 BT002
R03(AB)E_2P_G R03(AB)E_2P_G
UM4 UM4
PCB110
TCB412
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
CAUTION:SINCE THESE PARTS MARKED BY ARE R.SIGNAL
1
CRITICAL FOR SAFETY,USE ONES
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY G.SIGNAL
DANS LA NOMENCLATURE DES PIECES
B.SIGNAL
A B C D E F G H
G-23 G-24
A B C D E F G H
D3823
C3827
7 7
+-10%
2.7M 1/2W
TO DEFLECTION
PH3800 PH3801
R3806
D3821 SHORT W818
003P-2100 003P-2100
DEGAUSS COIL +B
1
UNREG+12V
8R140031
CP3800
C3826
A1561WV2-2P GND
1
1
2
2
R3828
TH3800_2
ZPB45BL3R0A 0.22 1W
6 6
RM11C-EIC
RM11C-EIC
D3815
D3818 R3829 R3830
D3808
1N4937 100 1/4W 1K 1/4W
KA
C3820
50V 10
L3803
W5T_20*10*10A
R3817 C3810 C3812 TO SOUND AMP
MLADE
200V 470 UP
S3802
D3817
WIDE
WHITE
C3815
WHITE 1 5W 500V 500V
RM11C-EIC
AC120V_60Hz
RM11C-EIC
BLACK SOUND+B
C3818
BLACK
D3809
D3816
1.5M 1/2W
CD3800 4 3
COIL,LINE FILTER
C3801
R3803
0R414903
L3801_1
2 1
F3800 1R1A223F28
51MS050L
5 5A125V 5
MTZJ18B
D3819 TO MICON/TUNER
D3810
W808
T3800 21DQ09N
R3826 R3827 81291074 POWER_FAIL
MHE
FH3800 FH3801
EYF-52BCY EYF-52BCY 5.0 GND
1.2M 1/4W 1.2M 1/4W 4.5V
10
C3822
2200
D3830
5A 125V 240 10.0
POWER B3800 5V 21DQ09N
8 11 NC 49
16V
Q3803
STP5NC50FP W5RH3.5X5X1.0 240 P2 8.0
48 D 240
W838
0.0015 R
G SB
7 12
6.3
240 0
C3811
S D3820
6 SG
0 13
2KV
R3816 P1 21DQ09N
MHE
240 135
135V
680 1/4W 5 14
C3823
4 4
25V 1000
0
D3811
HG
15
0.001 B
1SS133
C3814
0.47 1W
10.0 0
LG
R3821
HS3800 3 16
1W
763WAA0227
R3812
0 P4 12.0
12V
330
2 17
20.0 P3 8.0
8V
C3807 1 18
TO REGULATOR
7.3 13.6 100V 0.047 MMTS R3833 D3806
4
1
6.3 0.4
C3805
UNREG+8V
2
0.012 B 6.3
D3807 R3825 UNREG+5V
3 6.0 3
FEED BACK GND
1N4937 10 1/2W
MTZJ18B
METAL
FEED BACK
IC3800
SWITCHING 5.4
D3804
1SS133 MTZJ2.2B
D3828
KTC3198 Q3802
6.3
VR3800 470
KTC3203_Y
330 1/4W
R3804
3.9K 1/4W
25V 10 KA
1/2W
R3801
C3808
0.4
D3805
R3822
0
1K
B
0.01
R3805
56K 1/2W
W802
1SS133
D3822
1K
D3803
+-1%
1SS133
1SS133
250V 0.0047 KX
D3827
2 2
R3800
(2200PF)
C3816
MTZJ5.6B
1SS133
D3801
D3826
2.7K
R3831
100 1/4W
PCB250
TMB555
5A 125V
A B C D E F G H
G-25 G-26
A B C D E F G H
7 7
M2002 M2001
BCD3B02 JCL9B61
6 M M (SW PCB) 6
PCB640
BEC001
(RELAY PCB) SW2
SW1AB-271-10A
CP1
IMSA-9615S-08C-PP
8 SLD.MTR(-)
7 SLD.MTR(+)
6 SP.MTR(-)
5 SP.MTR(+)
S1005X S1005 S1005Y
4 L.SW
3 GND S1004X S1004Y
5 S1004 5
2 FG
S1001X S1001 S1001Y
1 VCC
PCB68A
82K
S1002X S1002Y
R2
BEC002 S1002
AWD28 4 3
560
R1
1 2
D1
4 SG-107F6 4
3 3
2 2
1 1
A B C D E F G H
G-27 G-28
A B C D E F G H
INTERCONNECTION DIAGRAM
8 8
SP351
SP352
8 OHM
8 OHM
COMMAND TRANSMITTER
SPEAKER
SPEAKER
TM101
R CH
L CH
CD301
CD302
OS2201
TO
1
2
1
2
7
6
2
3
4
5
1
H H NC H NC H NC CD2601
1
2
1
2
2 CP2601
CP301
CP302
TM101
2 3 2 3 2 3
FROM
T- 24 24 24 T-
SP OUT R+
SP OUT R-
SP OUT L+
SP OUT L-
1 1 1 1 T+ 23 23 23 T+
7 E E E E
7
REMOCON SENSOR
F- 22 22 22 F-
COAXIAL FRONT VIDEO JACK FRONT AUDIO JACK FRONT AUDIO JACK F+ 21 21 21 F+
OS2201
J4201 J2202 J2203 J2204 MON(DVD) 20 20 20 MON(DVD)
CP8001 CD4002 DVD
NC(SW) 19 19 19 NC(SW) DRIVE
V.OUT
YELLOW WHITE RED
GND
GND 1 1 GND
VOL(DVD) 18 18 18 VOL(DVD) DM-2
B+
HEADPHONE_JACK
GND 2 2 GND
J2201 GND(DVD) 17 17 17 GND(DVD)
TX 3 3 TX
LD(DVD) 16 16 16 LD(DVD)
RX 4 4 RX
LD(CD) 15 15 15 LD(CD)
GND(M) 5 5 GND(M)
VOL(CD) 14 14 14 VOL(CD)
P.CON+9V 6 6 P.CON+9V
GND(CD) 13 13 13 GND(CD)
P.CON+5V_A 7 7 P.CON+5V
MON(COM) 12 12 12 MON(COM)
P.CON+3.3V 8 8 P.CON+3.3V
GND(NC) 11 11 11 GND(NC)
P.CON+3.3V 9 9 P.CON+3.3V
6 RF 10 10 10 RF 6
GND 10 10 GND OPTICAL PICK-UP
C 9 9 9 C
SPDIF-134 11 11 SPDIF-134
B 8 8 8 B
CD8501
CP8002 CP8502 A 7 7 7 A
FFC
CVBS 12 12 1 1 CVBS D 6 6 6 D
GND 11 11 2 2 GND F 5 5 5 F
C(CVBS) 10 10 3 3 C(CVBS) E 4 4 4 E
GND 9 9 4 4 GND VCC 3 3 3 VCC
Y(G) 8 8 5 5 Y VREF 2 2 2 VREF
GND 7 7 6 6 GND GND(PDIC) 1 1 1 GND(PDIC)
AUDIO-L 6 6 7 7 AUDIO-L SPINDLE MOTOR
CD2602
GND 5 5 8 8 GND CP2602
FFC
AUDIO-R 4 4 9 9 AUDIO-R SLD- 1 1 1 SLD-
5 5
ZERO 3 3 10 10 ZERO SLD+ 2 2 2 SLD+
DVD RESET 2 2 11 11 DVD RESET SP1- 3 3 3 SP1-
SLED,LOADING MOTOR
GND 1 1 12 12 GND SP1+ 4 4 4 SP1+
LIMIT SW 5 5 5 LIMIT SW
AV PCB
GND 6 6 6 GND
PCB250
TMB555 SP_FG 7 7 7 SP_FG FG SENSER
+5V 8 8 8 +5V
FB401
FBT
TU001
CP2603
1
2
3
4
18
19
VMC319
HEATER
OPEN 3 OPEN
GND
NC 1
180V
CP803A
4 4
CP401
NC 2
5
4
3
2
1
3 +B
FOCUS SCREEN NC
NC
NC 4
NC 5
NC 6
NC
ANODE
CP802A
CP803B
NC 7
SCREEN
CLAMP 1
FOCUS
HEATER
GND
180V
R.OUT 4 NC 9 CP3800
CRT SOCKET
7
B.OUT 5
4
3
2
1
V801
J801_1
10 CLOCK 1
1
F
CLAMP_OFF 6
6
2
CRT
H.V
11 DATA
1
5
4
12 AFT OUT
CP801
MLADE
S3802
2
1
1
2
3
4
5
6
WIDE
AUDIO WHITE
13 WHITE
OUT
CLAMP OFF
S3801
AC120V_60Hz
CLAMP
NC 14 SIF OUT
GND
GND
B.OUT
BLACK
CD3800
CP802B
PCB110
TCB412 15 BT
AUDIO_OUT_R
AUDIO_OUT_L
SWD_VIDEO
DVD_VIDEO
P.CON+9V
2 2
I2C_SDA
I2C_SCL
NC 16 IF OUT
I2C OFF
GND
CD805 17 VIDEO
CP101
OUT
1
2
3
4
5
6
7
8
9
21
20
1
NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION:LES PIECES REPAREES PAR UN ETANT
1
DANGEREUSES AN POINT DE VUE SECURITE
DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
A B C D E F G H
G-29 G-30
WAVEFORMS
MPEG/MICON MICON/TUNER
AUDIO/VIDEO
POWER ON
10ns 500µs 0.2ms
100mV 500mV 1.0V
6 22
1
100ns 500µs
POWER ON
100mV 500mV
0.2ms
1.0V
2 7 23
MEMORY
POWER ON
5ns 10µs 0.2ms
200mV 200mV 1.0V
3 8 24
RF AMP/DSP
POWER ON
5ms
200ns 100µs
1.0V
500mV 200mV
25
4 9
POWER ON
200ns 10µs 50µs
100mV 100mV 1.0V
5 10 26
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
WAVEFORMS
VIF/SIF/CHROMA IN/OUT
POWER ON POWER ON DVD PLAY
20µs 10ms 0.5ms
0.5V 0.5V 200mV
27 32 37
28 33 38
29 34 39
30 35 40
31 36 41
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2
WAVEFORMS
POWER ON POWER ON
1ms 20µs
200mV 50V
42 47
DEFLECTION POWER
POWER ON STANDBY
5ms 5µs
10.0V 5.0V
43 48
POWER ON STANDBY
20µs 5µs
5.0V 5.0V
44 49
CRT
POWER ON
20µs
50V
45
POWER ON
20µs
50V
46
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-3
MECHANICAL EXPLODED VIEW
202 114
202
206
202
116
201
202
102
201
118 PCB110
201 (CRT PCB ASS'Y)
121
117
201
117
115
210
210
101E
101C
101F
A
210
101B 210
101D
101A
101
I1-1
MECHANICAL EXPLODED VIEW
113
112 110
208
209
209 208 208
209
209 208
208 208
208 208
120
209 208
PCB130 108
(DVD PCB ASS'Y)
205 208
208
205
205
208
205
208
112
119
106 203
208
208
109
104
208 208
206
208
203
A
107
204
103 207
206
204 204 206
211
211 PCB250
(AV PCB ASS'Y)
105
111
I1-2
MECHANICAL EXPLODED VIEW
(PACKING DIAGRAM)
123
127,128,129,130,
BL001,TM101
123
123
123
122
125
124
124
124
124
I1-3
DVD DECK EXPLODED VIEW
608 606
600
613 612 606
619
AA
AA 614
AA
618
616
SW1 AA
CD2302
AA
701 617
AA
AA
705
AA
603
615
AA AA
610
604 602
605 607
AA AA
605
622
AA 623
621 AA
609
601 M2602 620
CP1 611
PCB68A AA
(RELAY PCB ASS'Y)
702 CD2301
I2-1
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
J1-1
DVD DECK REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
J2-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
RESISTORS
! R401 AD301016 R3X28A331J R,METAL OXIDE 330 OHM 2W
! R402 AD300783 R3X181221J R,METAL OXIDE 220 OHM 1W
! R408 BZ210009 R3X28AR82J R,METAL OXIDE 0.82 OHM 2W
! R418 BZ210053 R002T22R2J RC 2.2 OHM 1/2W
! R442 AD300419 R4X5T6223F R,METAL 22K OHM 1/6W
! R444 AD300036 R4X5T6562F R,METAL 5.6K OHM 1/6W
! R445 AD302182 R002T4153J RC 15K OHM 1/4W
! R447 BZ210021 R65582680J R,FUSE 68 OHM 1/2W
R450 AD301761 R635815R6J R,FUSE 5.6 OHM 1W
! R803 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
! R805 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
! R807 BZ210050 R3X18A123J R,METAL OXIDE 12K OHM 2W
R2344 AE002014 R002021R2J RC 1.2 OHM 1/2W
R2345 AE002014 R002021R2J RC 1.2 OHM 1/2W
! R3803 BZ210206 R002T2155J RC 1.5M OHM 1/2W
! R3806 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R3812 BZ210217 R3X181331J R,METAL OXIDE 330 OHM 1W
! R3817 BZ210188 R5Y2CD010J R,CEMENT 1 OHM 5W
! R3821 AD300659 R3X181R47J R,METAL OXIDE 0.47 OHM 1W
! R3828 BZ210190 R63581R22J R,FUSE 0.22 OHM 1W
CAPACITORS
C313 BZ110101 E5EZF3222M CE 2200 UF 25V
! C402 BZ110195 E02LU8220M CE 22 UF 100V
! C403 BZ110016 E5EZT2471M CE 470 UF 16V
! C407 BZ210176 E02LF3222M CE 2200 UF 25V
C423 BZ110136 P4J7F3394J CMPP 0.39 UF 250V PMS
! C428 BZ110258 P4N8FJ862H CMPP 0.0086UF 1.25KV
C431 BZ110204 E0ELFD220M CE 22 UF 250V
C802 BZ110247 C0JBB0713K CC 0.001 UF 2KV B
C3007 AD302087 E02L05010M CE 1 UF 50V
! C3801 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
C3810 BZ110080 C0J0B0513K CC 0.001 UF 500V B
C3811 AE000874 C0PLRR7E3K CC 0.0015 UF 2KV R
C3812 BZ110080 C0J0B0513K CC 0.001 UF 500V B
! C3815 BZ110012 E51CGC471M CE 470 UF 200V
! C3816 AE002878 CD39E0MQ3M CC 0.0047UF 250V
C3818 BZ110101 E5EZF3222M CE 2200 UF 25V
! C3820 BZ110188 E50HU5100M CE 10 UF 50V
! C3822 AD300125 E5EZF2222M CE 2200 UF 16V
! C3823 BZ110032 E5EZF3102M CE 1000 UF 25V
! C3826 BZ110130 E62NFC221M CE 220 UF 200V
C3827 BZ110101 E5EZF3222M CE 2200 UF 25V
DIODES
D101 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D102 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D103 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D105 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D106 AD300070 D97U01201B DIODE,ZENER MTZJ12B T-77
D107 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D401 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D402 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D403 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77
D404 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77
D405 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D406 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D408 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
D409 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D410 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
D411 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D413 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D414 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D416 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
D603 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
D801 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D802 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D803 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D2201 BZ410087 0021E2Q140 LED LTL-1CHEE-002A
D2601 BZ410121 DDARDS1200 DIODE,SILICON KDS120RTK
D3003 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D3005 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
D3006 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
J3-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
DIODES
D3007 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D3008 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
D3009 AE000330 D97U03R61B DIODE,ZENER MTZJ3.6B T-77
D3801 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D3802 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D3803 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D3804 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
D3805 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D3806 AD301703 D2W0N49370 DIODE,SILICON 1N4937-B-EIC
D3807 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D3808 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D3809 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
D3810 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
D3811 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D3815 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D3816 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC
! D3817 BZ410115 D2LKB340L0 DIODE,SCHOTTKY SB340L-6737
! D3818 AD300731 D2WXN49370 DIODE,SILICON 1N4937
! D3819 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
! D3820 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
! D3821 BZ410080 D2WXRU2AM0 DIODE,SILICON RU2AM-EIC
D3822 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D3823 BZ410115 D2LKB340L0 DIODE,SCHOTTKY SB340L-6737
D3826 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D3827 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D3828 BZ410067 D97U02R21B DIODE,ZENER MTZJ2.2B T-77
! D3830 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
D3831 BZ410064 D97U03R91B DIODE,ZENER MTZJ3.9B T-77
D4001 BZ410119 DDDRL41480 DIODE,SILICON MCL4148
ICS
IC101 AE002888 I55D06079A IC OEC6079A
IC103 AD301641 I9UF032310 IC PST3231NR
IC199 AE002993 A5K305V255 IC S-24C04BDP-LA
! IC302 AD302184 I0FSP7522N IC AN7522N
! IC401 BZ611053 I01TD55220 IC AN5522
IC601 AD301765 I03FC63190 IC LA76319M-MPB-E
IC902 AD300059 I01FF58290 IC AN5829S
IC2301 BZ611126 I03F065600 IC LA6560
IC2601 AE002837 ICQK067080 IC ZR36708TQC
IC2602 AD301770 I07E00358F IC BA10358F-E2
! IC3001 BZ611015 I1KA97805A IC KIA7805API
IC3002 BZ611015 I1KA97805A IC KIA7805API
IC3005 BZ611033 I1KA97809A IC KIA7809API
! IC3800 AD301771 000220001W PHOTO COUPLER PS2561L1-1-V(W)
IC4001 AE000842 ICQK067620 IC ZR36762
IC4002 AE002137 ICRJ0C04N0 IC AT24C04N-10SI-2.7
IC4003 BZ611130 I0GF9XZ010 IC PQ070XZ01ZP
IC4005 AE000843 IF9J0164A7 IC M12L64164A-7T
IC4007 BZ611129 ICMJ0800A7 IC SST39VF800A-70-4C-EK
IC4201 AE001295 I0QJ045800 IC NJM4580M(TE1)
IC8502 AE002835 I17F02KEG0 IC PCM1742KEG/2K
TRANSISTORS
Q101 BZ510108 TAAA1504SY TRANSISTOR,SILICON KTA1504S_Y_RTK
Q105 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q301 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q302 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q305 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
! Q401 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA
! Q405 BZ510097 TCAT03227Y TRANSISTOR,SILICON KTC3227_Y-AT
! Q406 AD301779 TD3Q021400 TRANSISTOR,SILICON TT2140LS-YBC11
Q601 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q602 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q605 BZ510025 TPYJB05001 COMPOUND TRANSISTOR DTA114EKAT146
! Q804 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
! Q805 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
! Q806 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC
Q2201 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146
Q2601 BZ510112 T67J1036K0 TRANSISTOR,SILICON 2SA1036KT146
Q2602 BZ510112 T67J1036K0 TRANSISTOR,SILICON 2SA1036KT146
Q2603 BZ510113 T27T030180 FET 2SK3018
Q2604 BZ510113 T27T030180 FET 2SK3018
J3-2
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
TRANSISTORS
Q2605 BZ510113 T27T030180 FET 2SK3018
Q3000 BZ510057 TAAT01281Y TRANSISTOR,SILICON KTA1281_Y
Q3001 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146
! Q3003 AD301780 TCA0043690 TRANSISTOR,SILICON KTC4369(O,Y)
Q3004 BZ510057 TAAT01281Y TRANSISTOR,SILICON KTA1281_Y
Q3005 BZ510105 TCAT03209Y TRANSISTOR,SILICON KTC3209_Y-AT
Q3006 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q3007 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q3008 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q3009 BZ510105 TCAT03209Y TRANSISTOR,SILICON KTC3209_Y-AT
Q3010 BZ510057 TAAT01281Y TRANSISTOR,SILICON KTA1281_Y
Q3800 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! Q3802 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
! Q3803 BZ510093 TJXG5NC500 FET STP5NC50FP
Q4004 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q4201 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q4203 BZ510045 TNYJD05001 COMPOUND TRANSISTOR DTC144EKAT146
Q4209 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146
Q4210 BZ510081 TPYJA05001 COMPOUND TRANSISTOR DTA143EKAT146
Q4211 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q4212 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTK
Q8502 BZ510108 TAAA1504SY TRANSISTOR,SILICON KTA1504S_Y_RTK
Q8503 BZ510108 TAAA1504SY TRANSISTOR,SILICON KTA1504S_Y_RTK
Q8504 BZ510108 TAAA1504SY TRANSISTOR,SILICON KTA1504S_Y_RTK
COILS &TRANSFORMERS
L001 BZ310156 021375101K COIL 100 UH
L101 BZ310008 0216A6560K COIL 56 UH
L401 BZ310004 021679472K COIL 4.7 MH
L601 BZ310041 02167F101J COIL 100 UH
L602 BZ310156 021375101K COIL 100 UH
L801 AD301781 021673560K COIL 56 UH
L902 BZ310041 02167F101J COIL 100 UH
L904 BZ310041 02167F101J COIL 100 UH
L3000 AD301785 02167E100K COIL 10 UH
L3001 AD301785 02167E100K COIL 10 UH
! L3800 BZ310076 028R140031 COIL,DEGAUSS 8R140031
! L3801 AD301786 029T000110 COIL,LINE FILTER 1R1A223F28
L3803 AD301539 02AHB0A0A4 CORE,FERRITE W5T_20*10*10A
L4001 BZ310191 02167F2R2J COIL 2.2 UH
L4002 BZ310118 02AHB9A972 CORE,FERRITE W5T29X7.5X19
L4201 BZ310041 02167F101J COIL 100 UH
L4202 BZ310041 02167F101J COIL 100 UH
L8502 AE000828 02167F1R0K COIL 1 UH
L8503 AE000828 02167F1R0K COIL 1 UH
L8504 AE000828 02167F1R0K COIL 1 UH
T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T3800 AD301787 0481291074 TRANSFORMER,SWITCHING 81291074
JACKS
! J801 AD301147 066F120018 SOCKET,CATHODE RAY TUBE ISMS01S
! J2201 BZ614361 060J131015 HEADPHONE JACK MSJ-2000
J2202 BZ614146 060G421016 RCA JACK HTJ-032-05AY
J2203 BZ614147 060G421017 RCA JACK HTJ-032-05AW
J2204 BZ614280 060G421020 RCA JACK HTJ-032-05AR
J4201 BZ614400 060J401082 RCA JACK MSP-251V-05PBSN
SWITCHES
SW2213 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2214 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2215 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2216 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2217 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2218 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2219 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2220 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2221 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW2223 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
VARIABLE RESISTORS
VR401 BZ210255 V1K62H3BT8 VOLUME,SEMI FIXED NVG6THTB222
VR3800 BZ210265 V1K63Q2BTE VOLUME,SEMI FIXED NVG6TLTAB471
P.C.BOARD ASSEMBLIES
PCB110 AE002890 A5K304V110 PCB ASS'Y TCB412A
PCB130 AE002891 A5K304V130 PCB ASS'Y VMC319A
J3-3
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
P.C.BOARD ASSEMBLIES
PCB250 AE002994 A5K305V250 PCB ASS'Y TMB555A
MISCELLANEOUS
B301 BZ310129 024HT03564 CORE,BEADS W4BRH3.5X6X1.0
B401 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B2601 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B2602 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B2603 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B2604 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B2605 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B3800 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B4001 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4002 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4003 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4004 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4005 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4006 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4007 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4008 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4009 BZ310122 024HT03563 CORE,BEADS W4BRH3.5X6X1.0X2
B4010 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B4201 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B8502 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
B8503 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04
BL001 BZ310014 023C00022A COIL,BALUN HPN-01
BT001 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
BT002 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
CD301 BZ614324 06CU12414A CORD,CONNECTOR CU12414A
CD302 BZ614324 06CU12414A CORD,CONNECTOR CU12414A
CD802 BZ614404 WDL6032038 FLAT CABLE AWM2468 AWG26 6C BLACK 320MM
CD803 BZ614447 WBL6022038 FLAT CABLE AWM2468 AWG26 4C BLACK 220MM
CD805 BZ614175 06CU82039A CORD,CONNECTOR SM1098-009-1A
CP101 BZ614458 069S290629 CONNECTOR PCB SIDE A2001WV2-9P
CP301 BZ614268 069W120029 CONNECTOR PCB SIDE TID-X02P-M1
CP302 BZ614268 069W120029 CONNECTOR PCB SIDE TID-X02P-M1
CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
CP801 BZ614269 069S320010 CONNECTOR PCB SIDE A2361WV2-2P
! CD3800 AD300685 120R414903 CORD,AC BUSH 0R414903
CD4002 BZ614299 06CU2B2001 CORD,CONNECTOR CU2B2001
CD8501 AD301792 122H0C1001 CORD,JUMPER 2H0C1001
CP2601 AD302396 069JYOT099 CONNECTOR PCB SIDE IMSA-9631S-24Y901
CP2602 AD301858 069JV80180 CONNECTOR PCB SIDE IMSA-9615S-08C-PP
CP2603 AD301795 069S230639 CONNECTOR PCB SIDE A2001WR2-3P
! CP3800 AD300687 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP8001 BZ614214 069S2B0629 CONNECTOR PCB SIDE A2001WV2-11P
CP8002 AD301797 069J7C0029 CONNECTOR PCB SIDE IMSA-9604S-12Z14
CP802A BZ614333 067U006049 WIRE HOLDER B2013H02-6P
CP802B BZ614333 067U006049 WIRE HOLDER B2013H02-6P
CP803A BZ614334 067U004029 WIRE HOLDER B2013H02-4P
CP803B BZ614334 067U004029 WIRE HOLDER B2013H02-4P
CP8502 AD301798 069J7C0019 CONNECTOR PCB SIDE IMSA-9604S-12Z13
CUS011 BZ710149 800WFAA008 CUSHION C
EL001 BZ614044 124120301A EYE LET XRY20X30BD
EL002 BZ614043 124116281A EYE LET XRY16X28BD
F3800 BZ614504 081PC05005 FUSE 51MS050L
! FB401 AD301650 043214037F TRANSFORMER,FLYBACK FNI-14B001
FH3800 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY
FH3801 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY
OS2202 BZ614199 077Q004017 REMOTE RECEIVER PIC-37243SR
PH3800 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100
PH3801 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100
! SP351 BZ614200 070C533019 SPEAKER SG04D11BNA
! SP352 BZ614200 070C533019 SPEAKER SG04D11BNA
TM101 AD301799 076D0GD010 TRANSMITTER TOT201N09160
! TU001 AE000273 0163300005 RF UNIT 115-V-K015AR_B
! TH3800 BZ410079 DF5EL3R0A0 DEGAUSS ELEMENT ZPB45BL3R0A
! V801 AD301801 098Q1404D1 CRT W/DY A34AGT13X98(DL)
X101 BZ613019 1002T01606 CERAMIC OSCILLATOR CSTLS16M0X53-A0
X601 AD302003 100CT3R505 CRYSTAL HC-49/C
X4001 AD301803 100BT02701 CRYSTAL HC-49U/S
J3-4
ELECTRICAL REPLACEMENT PARTS LIST
RESISTOR
RC................... CARBON RESISTOR
CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR
J3-5
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN