Académique Documents
Professionnel Documents
Culture Documents
MO CellAlgoSwitch
Parameter ID DlSchSwitch
Parameter Name DL schedule switch
IsKey NO
Mandatory NO
Dynamic Attribute NO
Unit None
Impact CellAlgoSwitch
Interruption N/A
Scope
Interruption N/A
Duration (min)
Caution None
Impact on Radio FreqSelSwitch: If this switch is on, the subband CQIs reported by
Network UEs are used in downlink scheduling for UEs that meet the
Performance requirements for frequency selection, thereby increasing the
spectrum efficiency for UEs. If this switch is off, wideband CQIs
reported by UEs are used in downlink scheduling for all UEs.
ServiceDiffSwitch: If this switch is on, the eNodeB performs
differentiated control on different services carried by non-GBR
bearers. When the cell is congested, the data rate of different
services on the Uu interface can be controlled based on customized
priorities, ensuring that data transmission priorities of different
services can be dynamically adjusted. If this switch is off, the
eNodeB does not perform differentiated control on different
services carried by non-GBR bearers.
SpsSchSwitch: If this switch is on, the eNodeB performs semi-
persistent scheduling on VoIP services, and PDCCH resource overhead
and CQI reporting overhead decrease, which increases the VoIP
traffic volume. If this switch is off, the eNodeB performs dynamic
scheduling on VoIP services, and PDCCH resource overhead increases.
As a result, the VoIP traffic volume decreases, but the QoS of VoIP
services improves.
MBSFNShutDownSwitch: If this switch is on, more energy can be
conserved, but resource scheduling delay is prolonged. If this
switch is off, opposite effects are generated.
EnAperiodicCqiRptSwitch: Turning on this switch leads to timely
report of downlink channel quality and increased downlink data
rate. Because more control channel elements (CCEs) are consumed by
aperiodic CQI reporting, it is recommended that the
PdcchSymNumSwitch parameter be set to ECfiAdaptionON to decrease
the number of symbols consumed by enhanced aperiodic CQI reporting,
thereby further increasing downlink data rates. Turning off this
switch has no impact on network performance.
DlMbrCtrlSwitch: If the MBR is greater than the GBR and a GBR
bearer is set up for a UE, the eNodeB allocates more RBs to
downlink GBR services after this switch is turned on, thereby
increasing the downlink traffic volume on the GBR bearer. If the
MBR is equal to the GBR and only the non-GBR bearer is set up for a
UE, turning on this switch has no impact on network performance. If
the MBR is equal to the GBR and a GBR bearer is set up for a UE:
(1) Setting this switch to on has no impact on network performance
when RBs for downlink services are sufficient. (2) Non-GBR services
are affected by GBR services after this switch is on when RBs for
downlink services are insufficient. Setting this switch to off has
no impact on network performance.
MbrDlSchSwitch/UeAmbrDlSchSwitch: If the switch is on, throughput
of UEs with greater MBR/AMBR increases, and throughput of UEs with
smaller MBR/AMBR decreases. In addition, system throughput may also
be affected by the differences between MBRs/AMBRs of UEs and the
distribution of UEs in the cell. If this switch is off, the
throughput differences between UEs with different MBRs/AMBRs
decrease. In addition, system throughput is not affected by the
differences between MBRs/AMBRs of UEs or the distribution of UEs in
the cell.
EpfEnhancedSwitch: Setting this switch to on increases downlink
user throughput and improves user experience. Turning off this
switch has no impact on network performance.
AperiodicCqiTrigOptSwitch: Setting this switch to on reduces PDCCH
resources to be consumed and increases downlink throughput. Setting
this switch to off has no impact on network performance.
VoipTbsBasedMcsSelSwitch: Setting this switch to on decreases the
number of hybrid automatic repeat request (HARQ) retransmissions
for VoIP services and the scheduling delay of UEs in and near the
cell center.
DlSingleUsrMcsOptSwitch: If this switch is on and the load is low,
the local cell throughput increases; however, the interference with
neighboring cells increases, the neighboring cell throughput
decreases, and the IBLER increases. If this switch is off, network
performance is not affected.
UeSigMcsEnhanceSwitch: If this switch is on, the UE throughput
increases, and the UE MCS distribution is optimized. However, the
RRC reestablishment success rate slightly decreases, and the
service drop rate increases. If this switch is off, the UE
throughput decreases, the UE MCS distribution deteriorates.
However, the RRC reestablishment success rate and service drop rate
are not affected.
SubframeSchDiffSwitch: If this switch is on, the number of uplink
UEs scheduled increases but the number of downlink UEs scheduled
decreases; as a result, the uplink PRB usage increases but the
downlink PRB usage may decrease slightly. If this switch is off,
the number of uplink UEs scheduled decreases and as a result the
uplink PRB usage decreases.
TailPackagePriSchSwitch: If this switch is on, the connected tail
package is scheduled preferentially in the next TTI, which shortens
the delay and increases the transmission rate. If this switch is
off, the connected tail package is not scheduled preferentially in
the next TTI, which prolongs the delay and decreases the
transmission rate.
FreqSelJudgeIgnorDopplerSwitch: If this option is selected, Doppler
determination conditions are not considered during channel
frequency selective scheduling determination. You are advised to
select this option when the number of UEs in low-speed mobility is
large, so as to increase downlink frequency selective scheduling
gains. If this option is deselected, Doppler determination
conditions are considered during channel frequency selective
scheduling determination. You are advised to deselect this option
when the number of UEs in high-speed mobility is large, so as to
avoid negative gains caused by frequency selective scheduling on
UEs in high-speed mobility.
SIB1InterfRandSwitch: If this switch is on, the RBs scheduled for
neighboring cells do not overlap. The interference caused by the
RBs for SIB1s of the neighboring cells to the same target cell is
evenly distributed on the entire band. In this way, the SIB1
demodulation capability in the target cell is improved, reducing
the service drops caused by SIB1 demodulation failures. If this
switch is off, the RBs scheduled for neighboring cells overlap.
Attribute Radio
Applicable Mode L
MO CellAlgoSwitch
Parameter ID CqiAdjAlgoSwitch
Parameter Name CQI Adjust Algorithm Switch
IsKey NO
Mandatory NO
Dynamic Attribute NO
Unit None
Impact CellAlgoSwitch
Parameter None
Relationship
Access Read & Write
Interruption N/A
Scope
Interruption N/A
Duration (min)
Caution None
Impact on Radio CqiAdjAlgoSwitch: If this switch is on, the UE reports CQIs more
Network accurately, increasing the downlink rate. If this switch is off,
Performance the UE may report CQIs inaccurately, decreasing the downlink rate.
StepVarySwitch: If this switch is on, the IBLER convergence rate
can be adjusted based on site scenarios, increasing the downlink
rate in some scenarios. If this switch is off, the IBLER
convergence rate cannot be adjusted, decreasing the downlink rate
in some scenarios.
DlVarIBLERtargetSwitch: If this switch is on, the IBLER target
value can be adjusted in some scenarios, increasing the downlink
rate. If this switch is off, the IBLER target value cannot be
adjusted, decreasing the downlink rate in some scenarios.
TddBundlingCqiAdjOptSwitch: If this switch is on, UEs using the ACK
bundling mode enable the optimized CQI adjustment algorithm and
choose a more proper MCS mode, increasing downlink throughput of
each UE and cell average downlink throughput. If this switch is
off, UEs using the ACK bundling mode enable the non-optimized CQI
algorithm, which may result in a lower MCS value, smaller downlink
throughput of each UE, and smaller cell average downlink
throughput.
TddMultiplexingCqiAdjOptSwitch: If this switch is on, UEs using the
ACK multiplexing mode enable the optimized CQI adjustment mechanism
and choose a more proper MCS mode, increasing downlink throughput
of each UE and cell average throughput. If this switch is off, UEs
using the ACK multiplexing mode enable the non-optimized CQI
mechanism, which may result in an incorrect MCS value for special
subframes and decrease downlink throughput of each UE and cell
average downlink throughput.
AdaptiveStepVarySwitch: If this switch is on, the CQI adjustment is
performed at a large step in case of significant signal quality
changes, accelerating the IBLER convergence and therefore
increasing the downlink throughput. If this switch is off, the CQI
adjustment is performed at a fixed step, which has no impact on
network performance.
DlCqiAdjDeltaOptSwitch: If this switch is on, the IBLER convergence
performance improves and downlink throughput increases. However,
the RBLER and service drop rate may also increase.
Setting this switch to off has no impact on network performance.
DlEnVarIblerTargetSwitch: If this switch is on, downlink throughput
increases when channel quality fluctuates greatly or slightly or
the proportion of small-packet services is high. However, the RBLER
may increase. Setting this switch to off has no impact on network
performance.
DlRetxTbsIndexAdjOptSwitch: If this switch is on, both the downlink
RBLER and the service drop rate decrease, but downlink throughput
may also decrease slightly. Setting this switch to off has no
impact on network performance.
CfiConvertOptSwitch: If this switch is turned on, the CFI
calculation tables for normal and special subframes are optimized.
In this case, the MCS index is increased to improve downlink
throughput. However, the service drop rate may slightly increase.
BundlingOptThdSwitch: If this switch is turned on, the MCS index
threshold for enabling the optimized CQI adjustment algorithm in
TDD bundling mode decreases. In this case, when the downlink target
IBLER adaption algorithm is disabled, the optimized CQI adjustment
algorithm in TDD bundling mode helps increase the throughput of
CEUs with an MCS index ranging from 0 to 6. However, the IBLER, MCS
index, and service drop rate may also increase.
Attribute Radio
Applicable Mode L
MO CellDlschAlgo
Parameter ID RBPriMcsSelectStrategy
IsKey NO
Mandatory NO
Dynamic Attribute NO
Feature ID LOFD-00101501
LOFD-00101502
Unit None
Parameter None
Relationship
Interruption N/A
Scope
Interruption N/A
Duration (min)
Caution None
Attribute Radio
Applicable Mode L
MO CellPdcchAlgo
Parameter ID PdcchMaxCodeRate
Meaning Indicates the maximum coding rate on the PDCCH. The coding rate on
the PDCCH cannot exceed this parameter value. Otherwise the PDCCH
aggregation level must be increase.
IsKey NO
Mandatory NO
Dynamic Attribute NO
Enumeration N/A
Number/Bit
Unit None
Default Value 75
Recommended Value 75
Parameter None
Relationship
Access Read & Write
Interruption N/A
Scope
Interruption N/A
Duration (min)
Caution The actual value is equal to the GUI value divided by 100. The
default GUI value is 75, corresponding to an actual value of 0.75.
Attribute Radio
Applicable Mode L