Académique Documents
Professionnel Documents
Culture Documents
paperart
PAGE 1/19
Instructions for
Printing and Folding
Print on thin Paper and adhere the mask pieces to cardboard. This method
will result in the printed lines and pattern guide numbers being hidden on the
inside of the finished mask.
(1) Print your mask pieces on plain (4) Using a thick sewing needle or
printer paper. blunt knife and a ruler, score along the
folding lines.
(2) Glue the mask pieces to the back
of your cardboard. We recommend (5) Refer to the diagram below and fold
using spray adhesive or a glue stick as along the creases either bringing the
other types of glue may make the two edges towards you (Valley Fold)
paper too wet. for the plain dashed line folds or away
from you (Mountain Fold) for the dot/-
(3) Cut out the pattern pieces along dashed line folds.
the solid cutting lines.
(6) Proceed to Assembly Instructions
Note: the dashed lines are folding section.
lines, make sure not to cut them!
IMPORTANT
PAGE 2/19
Mask Assembly Instructions
Assembly
(8) After completing the mask you can
(7) Each number on the mask pattern optionally assemble our fitting band on
has a twin. Find the matching numbers the final page. Tape it to the inside to
and attach the two pieces together. get an optimal fit for your mask.
Option 1 / Easy
Clear Adhesive Tape
PAGE 3/19
ColOrS
SilveR pagE 5-16
Slit
PAGE 4/19
SilVer 4” (100mm)
17
10
8
11
glue
TogetheR
eaR
2
2
8
12
3
3
4
4 glue
TogetheR
1
13
gluE flapS
13 7
glue
TogetheR
7
6
15
17
14
16
PAGE 5/19
SilVer
25
33 26
19
glue 23
TogetheR
27
eaR
23
18 18
19
glue
24
20
TogetheR 20
21
28
28
22
29
30
30
glue
TogetheR
22
21
32
33
31
34
PAGE 6/19
SilVer
glue
64 TogetheR
64
49
57
65
65
52
59
55
62
PAGE 7/19
SilVer
51
50
49
54
52
53
55
11
56
PAGE 8/19
SilVer
51
58
57
61
59
60
62
27
63
PAGE 9/19
SilVer
73
76
80
31
79
74
32
29
24
66
60
61
75
PAGE 10/19
SilVer
35
77
14
85
15
84
71
1
12
53
69
54
67
PAGE 11/19
SilVer
82
40
78
39
41
83
38
36
87
37
PAGE 12/19
SilVer
58
68
75
70
66
72
74
81
PAGE 13/19
SilVer
50
68
67
70
69
71
72
86
PAGE 14/19
SilVer 4” (100mm)
47
39
45
45
41
43
43
w w w. l a p a s t u d i o s . c o m
44
44
38
46
46
36
48
PAGE 15/19
SilVer
56
10
63
9
26
16
25
Both Sides
77
34
35
76
37
73
48
40
47
PAGE 16/19
BlaCk
83
89
88
sliT
86
87
84
85
PAGE 17/19
BlaCk
88 89
sliT
78
81
82
79
80
PAGE 18/19
The Fitting Band
The fitting band for your mask will be made from strips of
cardboard paper and can be adjusted to get a good fit.
(1) Cut 3 strips of A4/US letter paper. (4) Tape the ends closed to make one
Each strip should measure 1.5" continuous loop of paper.
wide (40mm) and the length will be
the full length of the page. (5) Cut out 2 rectangles from the sheet
of paper, each one should measure
(2) Stick the short ends of the strips 1.5" x 4” (40mm x 100mm).
together with tape to make one
long strip of paper. (6) Tape one rectangle on either side
of the band (see drawing below).
(3) Wrap the long strip around your
head, overlapping the ends; make (7) Place the fitting band inside of the
sure that the resulting band is a mask and tape it to the back of
snug fit. the mask.
CutouT arRange
A4 papeR / us leTter papeR
1.5”/40mM
1.5”/40mM
1.5”/40mM
1.5”/40mM
4”/100mM
PAGE 19/19