Académique Documents
Professionnel Documents
Culture Documents
Login
Language |
User Guide
|
Dear Expert,
What are parameter can improve DL Traffic, DL user Throughput and PRB Utilization in LTE
network?
Thanks in advance!
LTELTE-FDDLTE UplinkLTE DownlinkPRB
Previous: LTE-A CA
Featured Answers
1.1.1 Recommended answer
(1)
from 4#
3 DL schedule switch
MO CellAlgoSwitch
Parameter ID DlSchSwitch
(1)
2#
Hello, Unicef.
Hope the following information will be helpful to you.
7 DL Max Throughput
MO TcpAckCtrlAlgo
Parameter ID DIMaxThroughput
Unit bit/s
Actual Value Range 0~4294967295
Default Value 0
Recommended Value 0
Impact TcpAckCtrlAlgo
Parameter None
Relationship
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio If the parameter value is smaller than the data rate over the air interface, the
Network Performance downlink throughput will decrease. If the parameter value is much greater
than the data rate over the air interface, the TCP ACK control algorithm
cannot take effect.
Introduced in BTS3900: V100R008C00
Version... BTS3900 LTE: V100R005C00
Attribute Radio
Applicable Mode L
8 DL Throughput Threshold
MO TCPACKLIMITALG
Parameter ID DLTHROUGHPUTTHRESHOLD
Unit kbit/s
Actual Value Range 1~4194304
Impact TCPACKLIMITALG
Parameter None
Relationship
Impact on Radio When the value of this parameter is less than the actual data rate on the air
Network Performance interface, the downlink throughput of TCP services decreases.
When the value of this parameter is much greater than the actual data rate
on the air interface, the TCP ACK buffer transmit function becomes
invalid.
Introduced in BTS3900: V100R009C00
Version... BTS3900 LTE: V100R009C00
Attribute Transport
Applicable Mode L
9 Uplink PRB threshold
MO CellShutdown
Parameter ID UlPrbThd
Unit %
Actual Value Range 0~100
Default Value 20
Recommended Value 20
Impact CellShutdown
Parameter In the CellShutdown MO, the sum of UlPrbThd and UlPrbOffset must
Relationship be smaller than or equal to 100.
Access Read & Write
Service Interrupted No (And no impact on the UE in idle mode)
After Modification
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Parameter ID DlPrbThd
Unit %
Actual Value Range 0~100
Default Value 20
Recommended Value 20
Impact CellShutdown
Parameter In the CellShutdown MO, the sum of DlPrbThd and DlPrbOffset must
Relationship be smaller than or equal to 100.
Access Read & Write
Service Interrupted No (And no impact on the UE in idle mode)
After Modification
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
(0)
3#
Thanks @BetterMing for above 4 parameters and how about these para. below:
DL schedule switch
CQI Adjust Algorithm Switch
PDCCH Power Boost Upper Limit
RB Priority MCS Select Strategy
(1)
4#
12 DL schedule switch
MO CellAlgoSwitch
Parameter ID DlSchSwitch
Impact CellAlgoSwitch
Parameter OutOfBandRelaySwitch under the RelaySwitch parameter in
Relationship the CellAlgoSwitch MO cannot be turned on when
MBSFNShutDownSwitch under the DlSchSwitch parameter is turned on.
If SuperCombCellSwitch of SfnAlgoSwitch in the CellAlgoSwitch MO is
set to on, SpsSchSwitch of DlSchSwitch in the CellAlgoSwitch MO must
be deselected.
Access Read & Write
Service Interrupted No (And no impact on the UE in idle mode)
After Modification
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio FreqSelSwitch: If this switch is on, the subband CQIs reported by UEs are
Network Performance used in downlink scheduling for UEs that meet the requirements for
frequency selection, thereby increasing the spectrum efficiency for UEs. If
this switch is off, wideband CQIs reported by UEs are used in downlink
scheduling for all UEs.
ServiceDiffSwitch: If this switch is on, the eNodeB performs differentiated
control on different services carried by non-GBR bearers. When the cell is
congested, the data rate of different services on the Uu interface can be
controlled based on customized priorities, ensuring that data transmission
priorities of different services can be dynamically adjusted. If this switch is
off, the eNodeB does not perform differentiated control on different
services carried by non-GBR bearers.
SpsSchSwitch: If this switch is on, the eNodeB performs semi-persistent
scheduling on VoIP services, and PDCCH resource overhead and CQI
reporting overhead decrease, which increases the VoIP traffic volume. If
this switch is off, the eNodeB performs dynamic scheduling on VoIP
services, and PDCCH resource overhead increases. As a result, the VoIP
traffic volume decreases, but the QoS of VoIP services improves.
MBSFNShutDownSwitch: If this switch is on, more energy can be
conserved, but resource scheduling delay is prolonged. If this switch is off,
opposite effects are generated.
EnAperiodicCqiRptSwitch: Turning on this switch leads to timely report of
downlink channel quality and increased downlink data rate. Because more
control channel elements (CCEs) are consumed by aperiodic CQI
reporting, it is recommended that the PdcchSymNumSwitch parameter be
set to ECfiAdaptionON to decrease the number of symbols consumed by
enhanced aperiodic CQI reporting, thereby further increasing downlink
data rates. Turning off this switch has no impact on network performance.
DlMbrCtrlSwitch: If the MBR is greater than the GBR and a GBR bearer is
set up for a UE, the eNodeB allocates more RBs to downlink GBR services
after this switch is turned on, thereby increasing the downlink traffic
volume on the GBR bearer. If the MBR is equal to the GBR and only the
non-GBR bearer is set up for a UE, turning on this switch has no impact on
network performance. If the MBR is equal to the GBR and a GBR bearer is
set up for a UE: (1) Setting this switch to on has no impact on network
performance when RBs for downlink services are sufficient. (2) Non-GBR
services are affected by GBR services after this switch is on when RBs for
downlink services are insufficient. Setting this switch to off has no impact
on network performance.
MbrDlSchSwitch/UeAmbrDlSchSwitch: If the switch is on, throughput of
UEs with greater MBR/AMBR increases, and throughput of UEs with
smaller MBR/AMBR decreases. In addition, system throughput may also
be affected by the differences between MBRs/AMBRs of UEs and the
distribution of UEs in the cell. If this switch is off, the throughput
differences between UEs with different MBRs/AMBRs decrease. In
addition, system throughput is not affected by the differences between
MBRs/AMBRs of UEs or the distribution of UEs in the cell.
EpfEnhancedSwitch: Setting this switch to on increases downlink user
throughput and improves user experience. Turning off this switch has no
impact on network performance.
AperiodicCqiTrigOptSwitch: Setting this switch to on reduces PDCCH
resources to be consumed and increases downlink throughput. Setting this
switch to off has no impact on network performance.
VoipTbsBasedMcsSelSwitch: Setting this switch to on decreases the
number of hybrid automatic repeat request (HARQ) retransmissions for
VoIP services and the scheduling delay of UEs in and near the cell center.
DlSingleUsrMcsOptSwitch: If this switch is on and the load is low, the
local cell throughput increases; however, the interference with neighboring
cells increases, the neighboring cell throughput decreases, and the IBLER
increases. If this switch is off, network performance is not affected.
UeSigMcsEnhanceSwitch: If this switch is on, the UE throughput
increases, and the UE MCS distribution is optimized. However, the RRC
reestablishment success rate slightly decreases, and the service drop rate
increases. If this switch is off, the UE throughput decreases, the UE MCS
distribution deteriorates. However, the RRC reestablishment success rate
and service drop rate are not affected.
SubframeSchDiffSwitch: If this switch is on, the number of uplink UEs
scheduled increases but the number of downlink UEs scheduled decreases;
as a result, the uplink PRB usage increases but the downlink PRB usage
may decrease slightly. If this switch is off, the number of uplink UEs
scheduled decreases and as a result the uplink PRB usage decreases.
TailPackagePriSchSwitch: If this switch is on, the connected tail package is
scheduled preferentially in the next TTI, which shortens the delay and
increases the transmission rate. If this switch is off, the connected tail
package is not scheduled preferentially in the next TTI, which prolongs the
delay and decreases the transmission rate.
FreqSelJudgeIgnorDopplerSwitch: If this option is selected, Doppler
determination conditions are not considered during channel frequency
selective scheduling determination. You are advised to select this option
when the number of UEs in low-speed mobility is large, so as to increase
downlink frequency selective scheduling gains. If this option is deselected,
Doppler determination conditions are considered during channel frequency
selective scheduling determination. You are advised to deselect this option
when the number of UEs in high-speed mobility is large, so as to avoid
negative gains caused by frequency selective scheduling on UEs in high-
speed mobility.
SIB1InterfRandSwitch: If this switch is on, the RBs scheduled for
neighboring cells do not overlap. The interference caused by the RBs for
SIB1s of the neighboring cells to the same target cell is evenly distributed
on the entire band. In this way, the SIB1 demodulation capability in the
target cell is improved, reducing the service drops caused by SIB1
demodulation failures. If this switch is off, the RBs scheduled for
neighboring cells overlap.
Introduced in BTS3900: V100R008C00
Version... BTS3900 LTE: V100R003C00
Attribute Radio
Applicable Mode L
13 CQI Adjust Algorithm Switch
MO CellAlgoSwitch
Parameter ID CqiAdjAlgoSwitch
Impact CellAlgoSwitch
Parameter None
Relationship
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio CqiAdjAlgoSwitch: If this switch is on, the UE reports CQIs more
Network Performance accurately, increasing the downlink rate. If this switch is off, the UE may
report CQIs inaccurately, decreasing the downlink rate.
StepVarySwitch: If this switch is on, the IBLER convergence rate can be
adjusted based on site scenarios, increasing the downlink rate in some
scenarios. If this switch is off, the IBLER convergence rate cannot be
adjusted, decreasing the downlink rate in some scenarios.
DlVarIBLERtargetSwitch: If this switch is on, the IBLER target value can
be adjusted in some scenarios, increasing the downlink rate. If this switch
is off, the IBLER target value cannot be adjusted, decreasing the downlink
rate in some scenarios.
TddBundlingCqiAdjOptSwitch: If this switch is on, UEs using the ACK
bundling mode enable the optimized CQI adjustment algorithm and choose
a more proper MCS mode, increasing downlink throughput of each UE and
cell average downlink throughput. If this switch is off, UEs using the ACK
bundling mode enable the non-optimized CQI algorithm, which may result
in a lower MCS value, smaller downlink throughput of each UE, and
smaller cell average downlink throughput.
TddMultiplexingCqiAdjOptSwitch: If this switch is on, UEs using the
ACK multiplexing mode enable the optimized CQI adjustment mechanism
and choose a more proper MCS mode, increasing downlink throughput of
each UE and cell average throughput. If this switch is off, UEs using the
ACK multiplexing mode enable the non-optimized CQI mechanism, which
may result in an incorrect MCS value for special subframes and decrease
downlink throughput of each UE and cell average downlink throughput.
AdaptiveStepVarySwitch: If this switch is on, the CQI adjustment is
performed at a large step in case of significant signal quality changes,
accelerating the IBLER convergence and therefore increasing the downlink
throughput. If this switch is off, the CQI adjustment is performed at a fixed
step, which has no impact on network performance.
DlCqiAdjDeltaOptSwitch: If this switch is on, the IBLER convergence
performance improves and downlink throughput increases. However, the
RBLER and service drop rate may also increase.
Setting this switch to off has no impact on network performance.
DlEnVarIblerTargetSwitch: If this switch is on, downlink throughput
increases when channel quality fluctuates greatly or slightly or the
proportion of small-packet services is high. However, the RBLER may
increase. Setting this switch to off has no impact on network performance.
DlRetxTbsIndexAdjOptSwitch: If this switch is on, both the downlink
RBLER and the service drop rate decrease, but downlink throughput may
also decrease slightly. Setting this switch to off has no impact on network
performance.
CfiConvertOptSwitch: If this switch is turned on, the CFI calculation tables
for normal and special subframes are optimized. In this case, the MCS
index is increased to improve downlink throughput. However, the service
drop rate may slightly increase.
BundlingOptThdSwitch: If this switch is turned on, the MCS index
threshold for enabling the optimized CQI adjustment algorithm in TDD
bundling mode decreases. In this case, when the downlink target IBLER
adaption algorithm is disabled, the optimized CQI adjustment algorithm in
TDD bundling mode helps increase the throughput of CEUs with an MCS
index ranging from 0 to 6. However, the IBLER, MCS index, and service
drop rate may also increase.
Introduced in BTS3900: V100R008C00
Version... BTS3900 LTE: V100R001C00
Attribute Radio
Applicable Mode L
14 RB Priority MCS Select Strategy
MO CellDlschAlgo
Parameter ID RBPriMcsSelectStrategy
Impact CellDlschAlgo
Parameter None
Relationship
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Parameter ID PdcchMaxCodeRate
Unit None
Actual Value Range 0.75~1.2, step:0.01
Default Value 75
Recommended Value 75
Impact CellPdcchAlgo
Parameter None
Relationship
Caution The actual value is equal to the GUI value divided by 100. The default GUI
value is 75, corresponding to an actual value of 0.75.
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio If this parameter is set to a smaller value, the maximum coding rate on the
Network Performance PDCCH is smaller, and the PDCCH aggregation level will be higher. In
this case, the PDCCH coverage is better, but the system capacity is smaller.
A larger value of this parameter results in the opposite effects.
Introduced in BTS3900: V100R010C00
Version... BTS3900 LTE: V100R010C00
Attribute Radio
Applicable Mode L
Show less
(0)
#5
(0)
#6
Hello @Unicef
What results did you come up with after playing around these parameters? Can you share some of your
ideas and results?
Thanks
DL schedule switch
CQI Adjust Algorithm Switch
PDCCH Power Boost Upper Limit
RB Priority MCS Select Strategy
and here can't attached file but after implement these parameters it's improve DL user throughput a
little bit from 3.5MB to 4MB in average after 3 days implement.
Rassim Reply Unicef Created Mar 12, 2020 09:57:37
Thanks, it seems that you still in monitoring of these parameters, please keep us updated for the final
conclusion.
Thanks
(0)
#7
Posted by BetterMing at 2020-02-21 03:45 Hello, Unicef.Hope the following information will be helpful to
you.DL Max ThroughputMOTcpAckCtrlAl ...
Hello @BetterMing
For the DL Max Throughput, The parameter (DL Max Throughput(bit/s) = 0) this is a recommended value,
while the range is very wide? from 0 to 4 Gbps.
And in the description of impact of this parameter, it is said "If the parameter value is smaller than the
data rate over the air interface, the downlink throughput will decrease" and for sure the throughput
must be more than 0 so don't you think it is contradictory issue?
Could you explain?
Comment
Reply
Advanced
Smilies
Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not
release content that may bring legal risks to all parties, including but are not limited to the following:
Do not share your account and password with others. All operations performed using your account will
be regarded as your own actions and all consequences arising therefrom will be borne by you. For
details, see " Privacy."
Unicef MVE
115
675
1
15.1.1 RECOMMENDED