Académique Documents
Professionnel Documents
Culture Documents
Answer
a highly refined mineral oil
since high temperatures are present,the oil used must be a non volatile and
it must have good expanding property.the oil is pure.it is replaced after
some years.
turbine 14 DTE
Answer
voltage exceeding 650 V and not exceeding 33000 V under
normal conditions as per IE Rules 1956
765kv in transmission lines.
440
Answer
The emf induced in the rotor depends upon the rotor frequency which further
depends on relative speed between rotor and synchronous speed of rotating
magnetic field. The relative speed at the time of starting or standstill is
maximum and hence large emf in induced in rotor conductors or winding due
to which very high current flows in rotor which is generally 5 to 7 times
of the full load or running current of an indication motor.
Answer
Dear, Back EMF is not present during starting (till rotor
achieves its speed) Hence starting curent will be high. You
can consider motor as a secondary shorted transformer
during starting. Hope it is clear now...
Answer
condenser store the energy in the form of heat
capacitor store the energy in the form of electrosatic field
Answer
condenser as name suggest that it absorbs the heat and
aswell as capacitor is a two plate device that only stores
electrostatic charge.
Answer
Condenser - Is a device used to Remove heat energy from a
fluid .
Capacitor - Is a device used to store electrical energy .
Answer
Neutral - it is '0' potential point makes closed loop for
the flow of current. Earth - Neutral point is connected to
earth for grouding the neutral current. normally the
current in the neutral point is zero but practically it
will have some value when short circuit or voltage
imbalance happens.
Answer
Earth : its connected to the body of all critcal equipments
like motors, panels, DG transformer to prevent shock &
safety for all machines.
Question a 3 phase slip ring induction motor is wound for 4 poles on stator and
6 poles on rotor; when 3 phase balanced voltage source at 50 hz is applied to
motor it will run at a)1500rpm b)1000rpm c)750 rpm d)zero rpm
Answer
If slip rings are shorted it will run at 1500 rpm.
Answer
In Indaction motor 120f/p wher consider P is number of pole
for indaction motor this pole cosider only stater coze we
give supply on stater. thus Ans is 1500rpm
Answer
why the input current is higher even at no-load.
Answer
answer b) 1000 rpm is correct. because 120f/p =N.here N is
the speed of the motor. hence f and p is the input frequency
and no of poles on the stator or rotor respectively
(depending upon which one is the rotating portion of the
motor) so and so, in general rotor is rotating so the answer
b) is correct. if the stator is rotating, answer b) is correct.
Answer
its bcoz Ns=120f/p
where Ns is the stator sychronous speed
f= supply frequency
p= no of supply poles i.e. stator poles
substituting values f=50 hz , p=4 ,
we obtain Ns=1500 r.p.m
Answer
hey fools
Answer
1000
Answer
zero rpm
Answer
first v 120f/p i.e. when 120 constant
f given ferquency
p is number of poles
Question What is the Polarisation index value ? (pi value)and simple definition
of polarisation index ?
Answer
it is ratio of insulation resistance (IR)for 10 minutes to
insulation resistance for 1 minute.
it should be 1.5
Answer
it is ratio of insulation resistance (IR)for 10 minutes to
insulation resistance for 1 minute.
it should be 2.5
Answer
Its ratio between insulation resistance(IR)i.e megger value
for 10min to insulation resistance for 1 min
it ranges from 5-7 for new motors & normally for motor to be
in good condition it should be >2.5 in case of PI value <2.5
over hauling should be conducted for motors and winding
should be thoroughly checked
a 3 phase slip ring induction motor is wound for 4 poles on stator and 6 poles on
rotor; when 3 phase balanced voltage source at 50 hz is applied to motor it will
run at a)1500rpm b)1000rpm c)750 rpm d)zero rpm
why for transformer protection we protect tranformer from 3rd hormonics and
5th hormonics and what is the reason of generating these horminics in electrical
system? Lg
• What types of CMOS memories have you designed? What were their size? Speed?
• What work have you done on full chip Clock and Power distribution? What process
• What types of I/O have you designed? What were their size? Speed?
used and how did you model the package/system? What parasitic effects were
considered?
• What types of high speed CMOS circuits have you designed?
• What transistor level design tools are you proficient with? What types of designs
• What products have you designed which have entered high volume production?
• What was your role in the silicon evaluation/product ramp? What tools did you
use?
• If not into production, how far did you follow the design and why did not you see
it into production?
Or, can we utilize two 9 volt batteries with a converter to create 12 volts of direct
current? Our
objective is to reduce the amount of batteries required, thus reducing the weight.
• Use two 9 V battery and build a simple resistive voltage divider. The setup is 18 V
from the two 9 V batteries connected in series and in series with 2 resistor R1
and R2. The desired output voltage 12 V will be taken between the 2 series
resistors R1 and R2. The formula is Vout=[R2/(R1+R2)]xVin. Or you can first get
the ratio [R2/(R1+R2)] that when multiplied with 18 V will result 12 V. Then the
you have a load on the 12V (which of course you do) then you will draw current
through R1. Thinking about that, you are going to drop your voltage due to power
dissipation in the resistor. Besides, the resistors are always consuming power in
Is there more information on the design, ie. Current requirements, battery life
expectation, etc. If so, then we can look into a more efficient design.
HELLO guys, Its BNM From NIT Rkl under metallurgy lemme aquaint u all with essar
selection process held at NIT ROURKELA on 29th Aug '08
1)Online Test( 4 parts:- Quantitative aptitude, Reasoning , English , Technical Section) each
section having 50 ques, time:- 2 hrs for online test u'll proceed to www.euphonyhr.com,
during test around 15 web pages having spsfc nos ques with timer running warn u at each
time , be cautious for that thing
Technical:-
y secondary steel making, wat r they, wats tundish, for making shaft of bikes wat type of
steel(ans=.25-.65 c steel)
Tricky Technical question:-
Q:-if u've given some metal, u r asked 2 make desired product, wat will be ur plannings?
Ans:- 1.mechanical working, 2)by taking metal as scrap melt it ,also add some alloying
elements==get a good qlty product....etc
(N.B.- in addition u must keep 1 imp thing in mind ,is economy factor while designing
products)
sir, in addition i'll try my best 2 find d way of b8r economical consideration(like Mn is
cheaper than Ni for making austenitic steel.etc think some other)
NOTA BENE:--
So to impress interviewr u gather paramount knowledge on >Iron making >steel making
>Heat treatment of steel.....Overlook idea about casting , m/cl wrking.. in addition ,have a
good idea bout indstrial trainng
If u wanna gain skill to get thro' any HR Round , follow "Gr8 tips 2 handle HR" published
under ESSAR-PLACEMENT PAPER
Hi friends,
The Company procedure is Written Test (Aptitude Test & Technical Test), Group
Discussion, Technical Interview and HR Interview. I want to share my experience with you
all.
The aptitude test consists of 3 sections – Verbal reasoning, Quantitative Aptitude and Logical
Reasoning comprising of 120 questions in 40 questions from each section.
3. The sum of a number whose ? th is 45. What is the number? Ans: None
4. The sum of a 2 digit number is equal to the difference between them. Find how many such
numbers are possible? Ans: 10
5. The sum of a 2 digit number is equal to twice the difference between them. Find how many
such numbers are possible?
8. One – fifth of two – third of a number is equal to 24. What is the number?
10. Ajith and Ajay’s age are in the ratio of 3:5. Two years hence, their age are in the ratio
7:11. What is Ajith’s present age? Ajith’s age = 12.
11. The length of a train is 200m and it crosses a platform of 75m in 15sec. Another train
with a length of 180m which is on the opposite direction approaches it. How long it will take
to cross the other?
12. (X) – Square, % - Square root, # - Divide, * - Multiply, @ - addition and & - Subtraction.
Find the value of (4)#4%4*4@4
14. A circle of diameter 28 cm. If there is a rectangle of length 56 cm. What is the value of
breadth whose areas are equal? Breadth = 44cm
15. A wheel rotates 18 revolutions in 4.5 sec. What are the revolutions of the wheel per
minute? Revolutions = 240
16. Solve: 20% of 60%of a number is equal to 40% of 200. What is the number?
19. Trisha’s monthly salary is 25% more than Krishna’s salary but 25% less than Payal’s
salary. Krishna’s annual income is Rs. 1, 20, 000. What is the monthly income of Payal?
20. There is a seven consecutive odd numbers. What is the number greater than 6 and it is
smaller than 6?
Technical Aptitude:
3. The power of 2 –stroke engine varies from 4 – stroke engine by______. Ans: Twice
b) Ease in storing
9. Gears are commonly called with _______ Ans: Pitch Circle Diameter
10. A good fuel should have ________ ignition point. Ans: Low
11. If heat supplied into the system is 30000 J/S and the power output is 9KW. What is the
efficiency of system? Ans:
12. A square rod of 2cm x 2cm of which a force of 8800Kg is acting on it. What is the stress
developed in it? Ans: 2200 Kg/cm2
15. Property of the freezing agent is: Ans: Low boiling point and high melting point
16. A diesel engine, that is, slow speed engine follows which cycle? Ans: Diesel Cycle
19. The potential energy raised upwards ___________ the kinetic energy downwards. Ans: is
equal to
21. For a thermodynamic system, the COP is 5 and the heat supplied to the system is 1 KW.
What is the work done?
The technical aptitude questions are given to the students who cleared Aptitude test and it
contains 50 questions.
After the Technical Aptitude is over, GD was conducted and the students who are short listed
are allowed for Technical Interview and HR Interview.
The Company procedure is Written Test (Aptitude Test & Technical Test), Group
Discussion, Technical Interview and HR Interview. I want to share my experience
with you all.
3. The sum of a number whose ? th is 45. What is the number? Ans: None
4. The sum of a 2 digit number is equal to the difference between them. Find
how many such numbers are possible? Ans: 10
5. The sum of a 2 digit number is equal to twice the difference between them.
Find how many such numbers are possible?
8. One – fifth of two – third of a number is equal to 24. What is the number?
10. Ajith and Ajay’s age are in the ratio of 3:5. Two years hence, their age are in
the ratio 7:11. What is Ajith’s present age? Ajith’s age = 12.
11. The length of a train is 200m and it crosses a platform of 75m in 15sec.
Another train with a length of 180m which is on the opposite direction
approaches it. How long it will take to cross the other?
12. (X) – Square, % - Square root, # - Divide, * - Multiply, @ - addition and & -
Subtraction. Find the value of (4)#4%4*4@4
15. A wheel rotates 18 revolutions in 4.5 sec. What are the revolutions of the
wheel per minute? Revolutions = 240
16. Solve: 20% of 60%of a number is equal to 40% of 200. What is the number?
19. Trisha’s monthly salary is 25% more than Krishna’s salary but 25% less than
Payal’s salary. Krishna’s annual income is Rs. 1, 20, 000. What is the monthly
income of Payal?
20. There is a seven consecutive odd numbers. What is the number greater than
6 and it is smaller than 6?
Technical Aptitude:
3. The power of 2 –stroke engine varies from 4 – stroke engine by______. Ans:
Twice
9. Gears are commonly called with _______ Ans: Pitch Circle Diameter
10. A good fuel should have ________ ignition point. Ans: Low
11. If heat supplied into the system is 30000 J/S and the power output is 9KW.
What is the efficiency of system? Ans:
12. A square rod of 2cm x 2cm of which a force of 8800Kg is acting on it. What is
the stress developed in it? Ans: 2200 Kg/cm2
15. Property of the freezing agent is: Ans: Low boiling point and high melting
point
16. A diesel engine, that is, slow speed engine follows which cycle? Ans: Diesel
Cycle
19. The potential energy raised upwards ___________ the kinetic energy
downwards. Ans: is equal to
21. For a thermodynamic system, the COP is 5 and the heat supplied to the
system is 1 KW. What is the work done?
The technical aptitude questions are given to the students who cleared Aptitude
test and it contains 50 questions.
After the Technical Aptitude is over, GD was conducted and the students who are
short listed are allowed for Technical Interview and HR Interview.
Technical Questions:
1) Composition of gunmetal?.
5) If a ball is kept at aheight of x(m),from that position it is dropeed .Does the p.e is equal to
the K.e if the ball goes inside the earth as same distance where it is relieved?.
7) What amount of power required to make the 2-strke petrol engine to 4-stroke diesel
engine?.
9) for the same compression ratio heat removed in each cycle is efficient in otto or diesel
cycle?.
10) Use of draft tube in turbine ?.a) to increase work o/p of runner b) To increase turbine
output.
23) Which law says that pressure can be transferred from onr point to another in an
undiminished form?.
24) Is Vane pump is Positive or non-positive displacement pump?.
27) In which process the temperature of the system changes but there is no heat transfer to the
surroundings?.
Hints: For Aptitude minimum preparation is sufficient, as time is less only go for selected Qs
in those books. since cut-off is only 9 its easy to complete written test, but care must be taken
not to spend on only one group (i.e., either reasoning or arithmatic or english).just attempt all
the Qs as there is no negative marking, such that you may be easyly qualified for aptitude
test.
For technical:
As I mentioned go through that book especially - Initial theory for each chapter before going
to multiple choices in that book, practice all multiple Qs in that book as max of Qs are given
from that directly.Some of the subjects you must concentrate on Production and
Manufacturing, Metallurgy and Material Sciences, Thermal, Design, Hydraulics.As cutoff is
23 Take care of this section, maximum disqualified from this section itself, but if u go
through that its very very easy.
GD Topics:
My topic is " " RELATION BETWEEN MAFIA LEADERS AND POLITICAL LEADERS
AND HOW IT EFFECT THE ECONOMICAL GROWTH OF OUR COUNTRY " ". Topics
are quitely different from software interviews. This is toughest topic they given on that day.
Just speakout 2 or 3 times fluently its enough. they wil not give much importance to this
stage.
Now the results are based on your performance in written test and your %marks(its
important) not GD. mostly 75% above wil be selected.(120 members are short listed for next
process)
The interview.
Hints: Dress code must be maintained for interview process, be confident while answering Qs
even they are wrong, keep a pleasent smile in your face, max 15 min they will interview, also
know something about company that will be added advantage.
2) bernoulis equation?
GD topics:
1 watt = 1Nm/S
1 h.p = ?kw
Acetylene dissolved in ?
The coupling is required to connect two parallel shaft distance between the shaft
is small
and variable?
Rupture strength==== ?
advantage of v-belt?
centipoises is unit of ?
drill angle?
v-belt angle?
say true/false:
in simple gear train every shaft is attached with one simple gear only
GD topics:
Technical Questions:
1) Composition of gunmetal?.
5) If a ball is kept at aheight of x(m),from that position it is dropeed .Does the p.e
is equal to the K.e if the ball goes inside the earth as same distance where it is
relieved?.
7) What amount of power required to make the 2-strke petrol engine to 4-stroke
diesel engine?.
9) for the same compression ratio heat removed in each cycle is efficient in otto
or diesel cycle?.
10) Use of draft tube in turbine ?.a) to increase work o/p of runner b) To increase
turbine output.
23) Which law says that pressure can be transferred from onr point to another in
an undiminished form?.
27) In which process the temperature of the system changes but there is no heat
transfer to the surroundings?.
Hints: For Aptitude minimum preparation is sufficient, as time is less only go for
selected Qs in those books. since cut-off is only 9 its easy to complete written
test, but care must be taken not to spend on only one group (i.e., either
reasoning or arithmatic or english).just attempt all the Qs as there is no negative
marking, such that you may be easyly qualified for aptitude test.
For technical:
As I mentioned go through that book especially - Initial theory for each chapter
before going to multiple choices in that book, practice all multiple Qs in that
book as max of Qs are given from that directly.Some of the subjects you must
concentrate on Production and Manufacturing, Metallurgy and Material Sciences,
Thermal, Design, Hydraulics.As cutoff is 23 Take care of this section, maximum
disqualified from this section itself, but if u go through that its very very easy.
GD Topics:
My topic is " " RELATION BETWEEN MAFIA LEADERS AND POLITICAL LEADERS
AND HOW IT EFFECT THE ECONOMICAL GROWTH OF OUR COUNTRY " ". Topics
are quitely different from software interviews. This is toughest topic they given
on that day. Just speakout 2 or 3 times fluently its enough. they wil not give
much importance to this stage.
Now the results are based on your performance in written test and your
%marks(its important) not GD. mostly 75% above wil be selected.(120 members
are short listed for next process)
The interview.
Hints: Dress code must be maintained for interview process, be confident while
answering Qs even they are wrong, keep a pleasent smile in your face, max 15
min they will interview, also know something about company that will be added
advantage.
2) bernoulis equation?
Hi Friends
Quantitative Aptitude - I
Question 3) On selling 17 balls at Rs. 720/-, there is a loss equal to the cost price
of 5 balls. The cost price of a ball in rupees is:
1. 45 2. 50 3. 55 4. 60 5. None of these
Question 5) The difference between a number and its four-fifth is 25. What is the
number?
1. 75 2. 100 3. 125 4. 150 5. None of these
Question 6) The difference between simple and compound interests compounded
annually on certain sum of money for two years at 4% per anum is Rs. 1/-. The
sum in Rs. is:
1. 625 2. 630 3. 640 4. 650 5. None of these
Question 7) A batsman scored 150 runs which included 5 boundaries, 2 sixes and
other singles. What percentage of his total score did he make by running
between the wickets?
1. 78.66 2. 75.66 3. 80.66 4. 82.66 5. None of these
Question 8) How many of the following numbers are divisible by 3 and not by 9?
2133, 2343, 3474, 4131, 5286, 5340
1. 2 2. 3 3. 4 4. 6 5. None of these
Question 9) Which of the following number will be wrong in the number series?
7 13 22 31 49 67 88
1. 13 2. 21 3. 31 4. 49 5. 67
Question 10) Two radios and one calculator can cost Rs.3300, while two
calculators and one radio cost Rs.5400. What is the price of a radio?
1. Rs. 2500 2. Rs. 700 3. Rs. 400 4. Rs. 1100 5. None of these
Question 11) The interest on a certain deposit at 4.5 p.c.p.a is Rs.202.50 in one
year. How much will the additional interest be in one year on the same deposit at
5 p.c.p.a?
1. 20.25 2. 22.50 3. 225 4. 427.5 5. None of these
Question 12) An alloy is to contain copper and zinc in the ratio 9 : 5. How much
zinc is required to be melted with 24 kg of copper?
1. 43.00 2. 43.20 3. 44.00 4. Cannot be determined 5. None of these
Question 14) A man in a train notices that he can count 20 electric poles in one
minute. If the poles are 40 meters apart, what is the speed of the train in Km/Hr?
1. 60 2. 45 3. 48 4. 54 5. None of these
Question 15) Two pipes A and B can fill a tank independently in 20 minutes and
30 minutes respectively. If both the pipes were used together, how long would it
take to fill the tank?
1. 12 min 2. 15 min 3. 25 min 4. 50 min 5. None of these
Question 16) If 24 men do a work in 40 days, in how many days will 30 men do
it?
1. 30 2. 28 3. 26 4. 34 5. None of these
Question 18) The average age of 28 employees is 23 years. If the manager’s age
is also included, the average age increases by one year. What is the manager’s
age in years?
1. 28 2. 51 3. 52 4. 53 5. None of these
Question 19) The difference between squares of two consecutive even numbers
is always divisible by:
1. 3 2. 4 3. 5 4. 2 5. None of these
Question 20) Ashutosh purchased a motor cycle at (13/15)th of its selling price
and sold it at 12% more than its selling price. Ashutosh’s net gain is:
1. 20% 2. 29.23% 3. 30.67% 4. 38.13% 5. None of these
Question 21) Which number should replace both the question marks in ? ÷ 32 =
392 ÷ ?
1. 112 2. 32 3. 16 4. 196 5. None of these
Question 23) A mother is three times as old as her son. After 15 years she will be
twice as old as her son. What is the present age of the mother in years?
1. 40 2. 50 3. 60 4. 70 5. None of these
Question 24) 'A' started business investing Rs.6000/-. Three months later 'B'
joined him investing Rs.4000/-. If they make a profit of Rs.5100/- at the end of
the year, how much should be ‘B’s’ share?
1. Rs. 1700 2. Rs. 3400 3. Rs. 1300 4. Rs. 1732.75 5. None of these
Question 25) 20 transistors go in a box and two dozen boxes are packed in a
carton. How many cartons will be needed to pack 1920 transistors?
1. 96 2. 12 3. 8 4. 4 5. None of these
Quantitative Aptitude - II
Subjects
41-50
31-40
21-30
11-20
1-10
Mathematics
23
09
48
12
08
Accounts
04
21
60
10
05
13
15
54
11
Question 1) If it is known that at least 28% marks are required for the students to
be eligible for a seminar on Accounts. The numbers of Accounts students who
can give the seminar are:
1. 85 2. 80 3. 95 4. 91 5. None of these
Question 4) What is the difference between the number of students passed with
at least 31 marks both in Accounts and Mathematics?
1. 9 2. 19 3. 12 4. 7 5. None of these
Expenditure of a company in Lac Rupees per annum over the given years
Year
Item of Expenditure
Salary
Bonus
Interest on Loans
Taxes
1998
150
100
25
85
1999
175
150
35
115
2000
200
175
10
45
75
2001
225
275
10
50
125
2002
250
400
20
45
100
TOTAL
1000
1000
50
200
500
Question 1) What is the percentage of the total amount of bonus paid by the
company during the given period in relation to the salary paid during the given
period?
1. 20% 2. 4% 3. 3% 4. 2% 5. None of these
Question 2) The total expenditure of the company for all items of expenditure for
the year 2002 is what percent of the year 2000?
1. 61 2. 18 3. 69 4. 38 5. None of these
Question 3) The total expenditure for all the items of expenditure in the year
1998 to the year 2002 is approximately:
1. 59% 2. 54% 3. 458% 4. 41% 5. None of these
Question 4) What is the average amount of interest per year, which the company
had to pay during these years?
1. 50 2. 35 3. 40 4. 45 5. None of these
Question 5) The ratio between the total expenditure on taxes and the total
expenditure on fuel and transport respectively for all the years is approximately:
1. 3 : 4 2. 1 : 2 3. 2 : 3 4. 1 : 4 5. None of these
Quantitative Aptitude - IV
Description:
The bar graph given below shows the foreign exchange reserves of a country in
million US$ for the years 1991-1992 to 1998-1999. Answer the questions based
on this graph given below:
Question 2) The average foreign exchange reserves over the period under review
are:
1. 325 2. 300 3. 314 4. 250 5. None of these
Question 3) The foreign exchange reserves of how many years is above the
average foreign exchange reserves of the given period?
1. 5 2. 2 3. 3 4. 4 5. None of these
Hi Friends
Eligiblity for 2009 passing out batch 60% in B.Tech and Date of Birth after 1-05-
1986.
Online written Test - This is the main round you have to clear it with good marks,
it will help you in the technical round so try to clear written technical with good
marks.
For Mathematical Aptitude : just remember the formulas of R.S AGGARWAL and
solve or concentrate on Examples. This is more than enough. If you are good in
calculations just concentrate at the time of test.
English: Passages are very easy and scoring, Fill in the blanks all from barron's
GRE 12th edition try to remember the answers of model test papers. Synonyms
Antonyms are very difficult, if you are good in English then only you can be
confident otherwise hit any options as I did.
Technical questions: As this was my 3rd attempt for a core company I realized
that all companys are asking mechanical questions from the book Mechanical
Engineering (conventional and Objective Type)
S.CHAND writter R.S. KHURMI and J.K.GUPTA so try to remember objective as
more as you can, it will help you for all campus selections.
In Essar if you perform well in written technical section then they will ask 1-2
question only in next technical round. Some of them are
Technical written:
11. If heat supplied into the system is 30000 J/S and the power output is 9KW.
What is the efficiency of system?
12. A square rod of 2cm x 2cm of which a force of 8800Kg is acting on it. What is
the stress developed in it?
16. A diesel engine, that is, slow speed engine follows which cycle?
19. The potential energy raised upwards ___________ the kinetic energy
downwards.
21. For a thermodynamic system, the COP is 5 and the heat supplied to the
system is 1 KW.
25. If a ball is kept at aheight of x(m),from that position it is dropeed. Does the
p.e is equal to the K.e if the ball goes inside the earth as same distance where it
is relieved?.
27. What amount of power required to make the 2-strke petrol engine to 4-stroke
diesel engine?.
29. for the same compression ratio heat removed in each cycle is efficient in otto
or diesel cycle?.
43. Which law says that pressure can be transferred from onr point to another in
an undiminished form?.
47. In which process the temperature of the system changes but there is no heat
transfer to the surroundings?.
48. In an ideal gas compared to a real gas at very high pressure occupies?
49. Kinetic theory of gases assumes that collisions between the molecules are?
50. The condition of perfect vacuum that is at absolute zero pressure can be
attained at?
56. When crude oil heated Which Hydro carbon comes first?
76. In what angle does an object thrown height will travel the longest distance?
78. The coupling is required to connect two parallel shaft distance between the
shaft is small and variable?
Technical
no favourite paper; they ask questions from manufacturing science, fluid
mechanics etc so remember definitions and procedures of mnufacturing sections
ex. which process is used for making piston, car body, engine cylinder coin etc
dont bluff on any question otherwise u will be rejected
TIPS:
answer in simple sentences, politely they may ask in hindi also if u are not good
in english and scored good in written technical
Only u have to be confident, genuine, don't bluff or guess on any question simply
say i dont know sir. they are very good and genuine people dont wear any tie.
Hi Friends
Analytical Reasoning - I
Question 2) If the following alphabet were written in the reverse order, which will
be the fifth letter to the right of the eleventh letter from the left?
ABCDEFGHIJKLMNOPQRSTUVWXYZ
1. J 2. K 3. L 4. P 5. U
Question 3) Four of the following five English words are alike in a certain way and
so form a group. Which is the one that does not belong to that group?
1. C-G 2. T-X 3. E-I 4. J-N 5. M-Q
Question 4) If the first and the third letters in the word CONTRIBUTION were
interchanged, also the second and fourth letters, the fifth and seventh and so on,
which letter would be eighth, counting from your left?
1. I 2. B 3. U 4. R 5. None of these
Question 5) If A ^ B means "A is the father of B" A < B means "A is the sister of
B", A > B means "A is the brother of B", then how is P related to R in the
following codified relationship?
R<S^P>T
1. Aunt 2. Cousin 3. Niece 4. Nephew 5. None of these
Question 11) In a certain game, if a person steps on the particular square he gets
one rupee and every time he misses the particular square he has to pay one
rupee. He is allowed to try 100 times and gets an amount of Rs. 40. How may
times did he step on the particular square?
1. 75 2. 65 3. 55 4. 60 5. 70
Analytical Reasoning - II
Description:
These questions are based on the following series of elements (English letters,
numerals and symbols).
AB8@E2$+5J36M*%P79S4U?1X{}
Question 1)
If the first two elements interchange their positions, the third and the fourth
elements interchange their positions, and so on and so forth, which of the
following triplet will show the exact sequence of the three elements in the new
arrangement?
1. X 1 { 2. 5 6 3 3. P M % 4. * P M 5. None of these
Question 3) How many such letters are there in the above series, each of which
is immediately preceded by a numeral and immediately followed by a symbol?
1. 2 2. 3 3. 4 4. 5 5. None of these
Description:
In the following questions the symbols <, >, &, £ and ? are used with the
following meaning:
A > B means A is smaller than B
A < B means A is greater than B
A & B means A is either greater than or equal to B
A £ B means A is either smaller than or equal to B
A ? B means A is equal to B
Now in each of the following questions assuming the given statements to be
true, find which of the two conclusions I & II given below them is/ are definitely
true?
Statement
J & I, C > O, I < O
Conclusions
I. C > J
II. C > I
Question 2)
Statement
J > S, S ? Z, Z > W
Conclusions
I. Z ? J
II. W > J
Question 3)
Statement
Y £ W, W ? X, X & U
Conclusions
I. Y > X
II. Y ? X
Question 4)
Statement
C < L, Z > J, L & Z
Conclusions
I. L > J
II. C < J
1. Only Conclusion I is true
2. Only Conclusion II is true
3. Either Conclusion I or Conclusion II is true
4. Neither Conclusion I nor Conclusion II is true
5. Both the Conclusions I and II are true
Question 5)
Statement
E & C, L < Z, C > Z
Conclusions
I. E < Z
II. L < C
Analytical Reasoning - IV
Description:
Each of the questions below consists of a question and two statements
numbered I and II are given below it. You have to decide whether the data
provided in the statements are sufficient to answer the question. Read both the
statements and –
Give answer (1) if the data in Statement I alone are sufficient to answer the
question, while the data in Statement II alone are not sufficient to answer the
question.
Give answer (2) if the data in Statement II alone are sufficient to answer the
question, while the data in Statement I alone are not sufficient to answer the
question.
Give answer (3) if the data in Statement I alone OR in Statement II alone are
sufficient to answer the question.
Give answer (4) if the data in both the Statements I and II are not sufficient to
answer the question.
Give answer (5) if the data in both the Statements I and II together are necessary
to answer the question.
CAUTION: Do NOT mark your answer unless you consider both the statements
carefully.
Question 1) If "6 5 9" stands for "we are healthy", which digit stands for
'healthy'?
I. "5 7" stands for "healthy habits".
II. "693" stands for "we are busy".
1. 2. 3. 4. 5.
Question 2) Who among A, B, C, D and E is the tallest?
I. E is taller than three of them but not as tall as A.
II. B is taller than D and C; but not tall as A.
1. 2. 3. 4. 5.
Question 3) In a seven-storey building with one flat on each storey, who among
A, B, C, D, E, & F occupies the middlemost flat?
I. A and D occupy the flats on the two extremes storeys and they have C and E
as their immediate neighbors.
II. The flat occupied by B is not in the middle.
1. 2. 3. 4. 5.
Question 4) Which code stands for "Brazil" in a code language in which "Mob"
stands for "Argentina."?
I. "Dip Mob Nod" denotes "Brazil defeated Argentina", in that code.
II. "Italy defeated Argentina" is denoted by " Sip Dip Mob" in that code.
1. 2. 3. 4. 5.
Question 5) What is the area of a circular playground that has a wire fencing
around it?
I. The cost of fencing was Rs. 15, 626 at the rate of Rs. 35 per Kg.
II. The fencing is 63 meters away from the center of the playground.
1. 2. 3. 4. 5.
Analytical Reasoning - V
Description:
Read the following information and answer the questions.
Question 2) With the given specifications, the only programme that can be
arranged on Monday is:
1. Semi classical 2. Light music
3. Pure classical 4. Cannot be determined 5. None of these
Question 3) Which of the following can be the last programme of the week?
1. Oddyssi or Katthak 2. only Oddyssi
3. only Pure classical 4. cannot be determined
5. none of these
Analytical Reasoning - VI
Description:
In each question below is given a statement followed by two assumptions
numbered I and II. An assumption is something supposed or taken for granted.
You have to consider the statement and the following assumptions and decide
which of the assumptions is implicit in the statement. Give answer
Question 1)
Statement
The only way to contain the circulation of black money in the market is to make
the tax laws more liberal and user friendly.
Assumptions
I. Tax laws in India are draconian and inadequate.
II. Circulation of black money in the market is undesirable.
1. 2. 3. 4. 5.
Question 2)
Statement
Teachers of many schools and colleges are breaking all norms of the profession
and provoking unnecessary controversies by entering into the active party
politics.
Assumptions
I. Teachers should be above party politics.
II. Teachers should take part in social activities rather than party politics.
1. 2. 3. 4. 5.
Question 3)
Statement
What is needed at the center to-day is the will and determination to govern and
not authoritarian government.
Assumptions
I. Authoritarianism and effective governance go hand in hand.
II. Will and determination to govern and non-authoritarian government are the
two sites of the same coin.
1. 2. 3. 4. 5.
Question 4)
Statement
India needs competent manpower just as urgently as it needs massive capital
inflow for rapid economic development.
Assumptions
I. India cannot achieve fast economic growth without massive does of capital.
II. Competent manpower is necessary for rapid economic development.
1. 2. 3. 4. 5.
Question 5)
Statement
If you want to understand the determinants of effective leadership, this is one of
the available books.
Assumptions
I. If is essential for everyone to understand the determinants of effective
leadership.
II. Wrong understanding may be gained if this book is not read.
1. 2. 3. 4. 5.
Description:
Question 1)
Statements
All fans are phones. All phones are letters. Some letters are bulbs.
Conclusions
I. Some letters are phones.
II. Some phones are fans.
III. All fans are letters
1. Only I follows
2. Only II follows
3. Only III follows
4. Only II and III follow
5. None follows
Question 2)
Statements
Most psychologists are historians. No historian is economist. All economists
are psychologists.
Conclusions
I. Some historians are psychologists
II. All psychologists are economists
III. No economist is historian.
1. Only II follows
2. Only I and II follow
3. Only II and III follow
4. Only I and III follow
5. None of these
Question 3)
Statements
Some flowers are gifts. All gifts are books. All books are tables.
Conclusions
I. Some tables are flowers.
II. Some flowers are tables.
III. All tables are books.
1. Only I follows
2. Only II follows
3. Only I and II follow
4. Only II and III follow
5. None of these
Question 4)
Statements
Some banks are factories. Some factories are offices. All offices are prisons
Conclusions
I. All prisons are factories.
II. Some Banks are prisons.
III. Some offices are banks.
1. None follows
2. All the three follow
3. Only I and II follow
4. Only II and III follow
5. Only I and III follow
Question 5)
Statements
All principals are teachers. All teachers are schools. All schools are grounds.
Conclusions
I. Some teachers are grounds.
II. All teachers are principals.
III. All principals are grounds.
Hi Friends
Its BNM From NIT Rkl under metallurgy. Let me aquaint u all with Essar selection
process held at NIT ROURKELA on 29th Aug '08
Generally, every interview system has HR round and Technical round. u Guys
need not be worried that a depth technical knowledge is reqd. so they got
confused and perform badly, Its noteworthy that, any1 can grab opportunity by
impressing interviewr thro' hr round only,, Use high profile, most professional
language with proper body language. courage n confidence r key 2
sucess//fearful n nervousness r key 2 failure
Technical:-
y secondary steel making, wat r they, wats tundish, for making shaft of bikes wat
type of steel(ans=.25-.65 c steel)
Tricky Technical question:-
Q:-if u've given some metal, u r asked 2 make desired product, wat will be ur
plannings?
Ans:- 1.mechanical working, 2)by taking metal as scrap melt it , also add some
alloying elements==get a good qlty product....etc
(N.B.- in addition u must keep 1 imp thing in mind, is economy factor while
designing products)
sir, in addition i'll try my best 2 find d way of b8r economical consideration(like
Mn is cheaper than Ni for making austenitic steel.etc think some other)
NOTA BENE:--
So to impress interviewr u gather paramount knowledge on >Iron making >steel
making >Heat treatment of steel.....Overlook idea about casting , m/cl wrking.. in
addition, have a good idea bout indstrial trainng
Hi Friends
This is Vinod Singh Amar from Department of Chemical Engineering, R.V.R & J.C
College of Engineering, Guntur, A.P. Welcome to the world of core jobs. Wishing
u all the best for your career in the everlasting CORE field espacially in field of
CHEMICAL ENGINEERING.
Well, about ESSAR, the selection process in divided into five modes:
1)Preplacement Talks
2)Online Test
3)Group Discussion
4)Technical Interview
5)H.R Interview
At first, there was a preplacement talk section, where all the other college
students who came to attend the off campus selection irrespective of all
branches (Chemical, EEE, Mech, EIE) attended in the seminar hall. The HR
manager of ESSAR gave a brief discussion about the company. And then he
explained the procedure for the written online aptitude test (which was the next
step). Finally he asked us whether we have any doubts reg their company. I was
the only one who dared to ask a small doubt for which I recieved a clear answer.
So be prepared for one to three questions to ask about the company, where the
Manager wants to test our skills.
Note that all the sections may appear in any order in the online test. So please
dont panic.. Please be fully prepared. Beware that TIMER IS RED IN COLOR ON
THE SCREEN. So time management is most important. there will be a sectional
cut off of 9 each in the 1, 2, 3 sections (as above) and 23 for 4 section (given
above).
1)In Quantative section there will be model bits from GRE baron, and R.S Agarwal
(like time and distance, simple and compound interest, data intrepretation, profit
and loss, ratios and proportions, mixtures, Coding and Decoding from rs agarwal
topics)
2)For Verbal section stress mainly on the reading comphrension and jumbled
sentences (you will clear the cut off). No anologies or antonyms or synonyms will
be given.
3)For Verbal Reasoning, from R.S Agarwal
After you have cleared the online test there will be a group discussion where
there will be a additional score for Speaking First in the team (INITIATION).
Speak confidently with eye to eye contact (For this you must be a good liar in
your daily life) for two to three times and always try to conclude the topic by
yourself at the end.
Technical Questions:
1) Composition of gunmetal?.
5) If a ball is kept at aheight of x(m), from that position it is dropeed .Does the
p.e is equal to the K.e if the ball goes inside the earth as same distance where it
is relieved?.
7) What amount of power required to make the 2-strke petrol engine to 4-stroke
diesel engine?.
9) for the same compression ratio heat removed in each cycle is efficient in otto
or diesel cycle?.
23) Which law says that pressure can be transferred from onr point to another in
an undiminished form?.
27) In which process the temperature of the system changes but there is no heat
transfer to the surroundings?.
It is quite easy, there was appreciable elimination in GD. (checked only the
logical ability, clarity of thought and simple English)
Apart from that First round is online test comprises of 120 question equally
divided into four sections (V, L, Apti, Tech). U need to be really quick in this
because there will be Time count on the screen itselt.
Hi Friends
This is just to give a brief idea about ESSAR STEEL selection procedure.....
PATTERN:
Written Test,
GD,
Technical Interview,
HR Interview.
GROUP DISCUSSION:
This may or may not be there (depending on the number of selected candidates
in written ). It is just for formality.. Ur performance in GD plays less role and ur
percentage and written performance plays more role to get through GD.But try
to perform better... Topics are very common topics. You can clear it easily....
After some time they told results will be sent to ur respective colleges and we
left the venue. Results came after a month.... (on sep 13th). But I haven't got the
job. I felt very sad. In that list total 38 members were selected..
After some days (on oct 12th) they sent another list. By God's grace I was
selected in that list (another 17 was selected). i.e until that date we are in
waiting list. I came to know that we are all in waiting list because of eye site...
Hi Friends
The Company procedure is Written Test (Aptitude Test & Technical Test), Group
Discussion, Technical Interview and HR Interview. I want to share my experience
with you all.
3. The sum of a number whose ? th is 45. What is the number? Ans: None
4. The sum of a 2 digit number is equal to the difference between them. Find
how many such numbers are possible? Ans: 10
5. The sum of a 2 digit number is equal to twice the difference between them.
Find how many such numbers are possible?
8. One - fifth of two - third of a number is equal to 24. What is the number?
10. Ajith and Ajay's age are in the ratio of 3:5. Two years hence, their age are in
the ratio 7:11. What is Ajith's present age? Ajith's age = 12.
11. The length of a train is 200m and it crosses a platform of 75m in 15sec.
Another train with a length of 180m which is on the opposite direction
approaches it. How long it will take to cross the other?
12. (X) - Square, % - Square root, # - Divide, * - Multiply, @ - addition and & -
Subtraction. Find the value of (4)#4%4*4@4
15. A wheel rotates 18 revolutions in 4.5 sec. What are the revolutions of the
wheel per minute? Revolutions = 240
16. Solve: 20% of 60%of a number is equal to 40% of 200. What is the number?
19. Trisha's monthly salary is 25% more than Krishna's salary but 25% less than
Payal's salary. Krishna's annual income is Rs. 1, 20, 000. What is the monthly
income of Payal?
20. There is a seven consecutive odd numbers. What is the number greater than
6 and it is smaller than 6?
Technical Aptitude:
3. The power of 2 -stroke engine varies from 4 - stroke engine by______. Ans:
Twice
9. Gears are commonly called with _______ Ans: Pitch Circle Diameter
10. A good fuel should have ________ ignition point. Ans: Low
11. If heat supplied into the system is 30000 J/S and the power output is 9KW.
What is the efficiency of system? Ans:
12. A square rod of 2cm x 2cm of which a force of 8800Kg is acting on it. What is
the stress developed in it? Ans: 2200 Kg/cm2
15. Property of the freezing agent is: Ans: Low boiling point and high melting
point
16. A diesel engine, that is, slow speed engine follows which cycle? Ans: Diesel
Cycle
19. The potential energy raised upwards ___________ the kinetic energy
downwards. Ans: is equal to
21. For a thermodynamic system, the COP is 5 and the heat supplied to the
system is 1 KW. What is the work done?
The Technical Aptitude questions are given to the students who cleared Aptitude
test and it contains 50 questions.
After the Technical Aptitude is over, GD was conducted and the students who are
short listed are allowed for Technical Interview and HR Interview.
Hi Friends
GD :
topic : reservation
and some common topics only
Kinetic theory of gases assumes that collisions between the molecules are?
Acetylene dissolved in ?
Advantage of V belt?
In what angle does an object thrown height will travel the longest distance?
The coupling is required to connect two parallel shaft distance between the shaft
is small and variable?
Rupture strength==== ?
advantage of v-belt?
poisson ratio?
endurance limit is depend upon-1.toughness 2.elasticity 3.britleness?
centipoise is unit of ?
drill angle?
v-belt angle?
say true/false:
in simple gear train every shaft is attached with one simple gear only
Radiation heat transfer is varied with T to the power of 4.
GD topics:
Democracy is the only way to sustain economy growth
Should Indian youth involving Politics
Foreign investment should allow directly to India
Foods come first ethics come later
TV channels can be regional, International
Hi Friends
Selction Stages: Written Test, GD, Technical Inteview, HR Int, Group talk.
Procedure: For Written Test: Total 120 Qs, 40-reasoning, 40-Arithmatic, 40-
English, Time:80min.
Aptitude Technical written test: 50Qs, Time:30min. Cut off: For Aptitude Each
Section - 9, Total - 27/120 (min).
For technical:
As I mentioned go through that book especially - Initial theory for each chapter
before going to multiple choices in that book, practice all multiple Qs in that
book as max of Qs are given from that directly.Some of the subjects you must
concentrate on Production and Manufacturing, Metallurgy and Material Sciences,
Thermal, Design, Hydraulics.As cutoff is 23 Take care of this section, maximum
disqualified from this section itself, but if u go through that its very very easy.
GD Topics:
My topic is RELATION BETWEEN MAFIA LEADERS AND POLITICAL LEADERS AND
HOW IT EFFECT THE ECONOMICAL GROWTH OF OUR COUNTRY. Topics are
quitely different from software interviews. This is toughest topic they given on
that day. Just speakout 2 or 3 times fluently its enough. they wil not give much
importance to this stage.
Now the results are based on your performance in written test and your
%marks(its important) not GD. mostly 75% above wil be selected.(120 members
are short listed for next process)
First the Technical Interview: they will start this section from Qs like Tell me
about yourself, hobbies, xtra curicular activities etc like this, all this is to make us
feel comfort. next they wil ask concept oriented Qs from our subjects. however
this section some bit tough, those who are good in basic concepts they will easily
go through next process.
Hints: Dress code must be maintained for interview process, be confident while
answering Qs even they are wrong, keep a pleasent smile in your face, max 15
min they will interview, also know something about company that will be added
advantage.
I answered on an Avg he asked me : you answerd 50-50 then why wil I hire you?
this Qs helps me alot for my selection. i answered already my prepared answer. i
also tell him about the comapny details also, then he impress my answer i also
drawn attention from HR he's also there interviewing other people
simultaneously. Then i got a HR form.(90 members shortlisted).
HR interview:
you have to fill HR form first, neatly and confidentially. HR interviewer is friendly
and he wil ask general Qs like
1) why did u take ME branch?
2) about yourself?
3) family background?
4) why do you want to join in our company?
5) what do u know about our company?
6) what's the salary you expecting?
I answerd these Qs well. Then they will gather all the selected candidates upto
now in a room. they will observe the personalities and then the GROUP TALK: in
this section you have to tell about yourself for 2min to the selected candidates,
every one should do that. The HR and Technical interviewers observe us, along
with our resumes, written test performances, interview performances,
pesonality.(55 members shortlisted upto now). The results will be announced
after a month
JOINING DATE WILL BE GIVEN ON JULY 16TH 2007 ONE BATCH AND JULY 23RD
2007 SECOND BATCH. AT SURATH AS GRADUATE ENGINEER TRAINEES.
WORK HARD - BE CONFIDENT- BE PATIENCE THESE 3 THINGS WILL MAKE U
SELECT CONFORMLY.
Kinetic theory of gases assumes that collisions between the molecules are?
Acetylene dissolved in ?
Advantage of V belt?
In gear boxes Which type of key is used
In what angle does an object thrown height will travel the longest distance?
The coupling is required to connect two parallel shaft distance between the
shaft is small and variable?
Rupture strength==== ?
advantage of v-belt?
The key used in the gears for transmitting power(flat/saddle/spline/square)
poisson ratio?
centipoises is unit of ?
drill angle?
v-belt angle?
GD topics:
Paper: ESSAR GROUP Placement Paper on 3rd August 2006 at Anna University
(Aptitude & Technical)
The Company procedure is Written Test (Aptitude Test & Technical Test), Group
Discussion, Technical Interview and HR Interview. I want to share my experience
with you all.
The aptitude test consists of 3 sections " Verbal reasoning, Quantitative Aptitude
and Logical Reasoning comprising of 120 questions in 40 questions from each
section.
Aptitude Section:
3. The sum of a number whose ? th is 45. What is the number? Ans: None
4. The sum of a 2 digit number is equal to the difference between them. Find
how many such numbers are possible? Ans: 10
5. The sum of a 2 digit number is equal to twice the difference between them.
Find how many such numbers are possible?
8. One " fifth of two " third of a number is equal to 24. What is the number?
10. Ajith and Ajay's age are in the ratio of 3:5. Two years hence, their age are in
the ratio 7:11. What is Ajith's present age? Ajith's age = 12.
11. The length of a train is 200m and it crosses a platform of 75m in 15sec.
Another train with a length of 180m which is on the opposite direction
approaches it. How long it will take to cross the other?
12. (X) " Square, % - Square root, # - Divide, * - Multiply, @ - addition and & -
Subtraction. Find the value of (4)#4%4*4@4
15. A wheel rotates 18 revolutions in 4.5 sec. What are the revolutions of the
wheel per minute? Revolutions = 240
16. Solve: 20% of 60%of a number is equal to 40% of 200. What is the number?
19. Trisha's monthly salary is 25% more than Krishna's salary but 25% less than
Payal's salary. Krishna's annual income is Rs. 1, 20, 000. What is the monthly
income of Payal?
20. There is a seven consecutive odd numbers. What is the number greater than
6 and it is smaller than 6?
Technical Aptitude:
3. The power of 2 "stroke engine varies from 4 " stroke engine by______. Ans:
Twice
9. Gears are commonly called with _______ Ans: Pitch Circle Diameter
10. A good fuel should have ________ ignition point. Ans: Low
11. If heat supplied into the system is 30000 J/S and the power output is 9KW.
What is the efficiency of system? Ans:
12. A square rod of 2cm x 2cm of which a force of 8800Kg is acting on it. What is
the stress developed in it? Ans: 2200 Kg/cm2
15. Property of the freezing agent is: Ans: Low boiling point and high melting
point
16. A diesel engine, that is, slow speed engine follows which cycle? Ans: Diesel
Cycle
19. The potential energy raised upwards ___________ the kinetic energy
downwards. Ans: is equal to
21. For a thermodynamic system, the COP is 5 and the heat supplied to the
system is 1 KW. What is the work done?
The technical aptitude questions are given to the students who cleared Aptitude
test and it contains 50 questions.
After the Technical Aptitude is over, GD was conducted and the students who are
short listed are allowed for Technical Interview and HR Interview.