Académique Documents
Professionnel Documents
Culture Documents
This manual is applicable for V3013 series Embedded Network Digital Video Recorders. V3013 series
employs the most advanced technology in the information industry, such as video/audio
encoding/decoding, hard disk recording and TCP/IP. They incorporate features of both digital
video/audio recorder (DVR) and digital video/audio server (DVS). V3013 series can function
stand-alone or can be used to build a powerful surveillance network, widely used in banking,
telecommunications, transportation, factories, warehousing, and other applications.
Note: This manual applies to V3013 series DVRs. Because V3013 series DVRs with different channels
have the similar function and operation, we take 16-CH DVR as an example in this manual to describe
the installation and operation procedures.
Notice
Copyright Statement
This manual may not be reproduced in any form or by any means to create any derivative such as translation, transformation, or adaptation
without the prior written permission of Infinova.
Infinova reserves the right to change this manual and the specifications without prior notice. The most recent product specifications and
user documentation for all Infinova products are available on our website www.infinova.com
Trademarks
Infinova® is a trademark of Infinova.
Copyright © 2000-2010 Infinova. All rights reserved
All other trademarks that may appear belong to their respective proprietors.
FCC Warning
V3013 series Network Digital Video Recorders all comply with Part 15 of the FCC rules.
Operation is subject to the following two conditions.
y This device may not cause harmful interference.
y This device must accept any interference received, including interference that may cause undesired operation.
V3013 series Network Digital Video Recorders have been tested and found to comply with the limits for Class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
Read this manual carefully before installation. This manual should be saved for future use.
Indicates that the un-insulated components within the product may carry a voltage harmful to humans.
Indicates operations that should be conducted in strict compliance with instructions and guidelines contained in this manual.
Warning: To avoid risk of fire and electric shock, keep the product away from rain and moisture!
Install Environment and Notes
Install Environment
z Working temperature of DVR: -10℃~50℃,storage temperature -10℃~70℃.
z DVR should be placed flatly during installtion or operation, avoid slantways or inversed placement.
z Avoid placement and installation in high temperature and high humidity.
z For better heat-radiation, cooling fan is designed inside the DVR. Further, install the device in the place with good ventilation condition.
z To ensure a better heat-radiation, the distance between the DVR back panel and the other DVR or the wall should be more than 6CM.
z Do not move DVR in the place with sharp temperature contrast to avoid condensation inside the device which will shorten the lifespan
of the machine.
z Install the thunder protection devices for the DVR applied in thundery areas to prevent the thunder-caused hardware damages.
Notes
z Don’t touch the power button or DVR with wet hands or wet stuff.
z After the installation, to avoid the interference of the video/audio signals and the damages caused by the static electricity, please make
sure that DVR and the housing are well grounded (refer to the grounding interface on the rear panel).
z Make sure that the voltage of the power supply is stable. Do not close the DVR directly by turning off the general switch.
z Avoid splashing down the liquid or metal on DVR, which may cause short circuit even fire inside DVR.
z Install the harddisk correctly before use, or else, you can’t make any record operation.
z The dust of the mainboard may cause short circuit after being damped, therefore, to maintain a long life usage of the device, please clean
the mainboard, inserts, housing and cooling fan regularly with the brush.
z Try not to apply TV set at the local video output interface (VIDEO OUT), otherwise, the output circuit of the DVR (VIDEO OUT) is apt
to damages.
z When shut down the DVR, do not turn off the power switch directly. Please firstly close the current recording, then complete the
software shut down via menu, and at last close the power switch on the rear panel. In this way, the possible hardware damages are
avoided.
z DVR is enable to auto-check the harddisk, when a new harddisk without formating or a nonsupport file system of the harddisk, system
will alarm to user, the record could be taken only after the harddisk is formatted. If the harddisk has been used before and meanwhile it
has subareas record, please delete the subares on PC first, and then format the harddisk in DVR. Otherwise, the normal record will be
influenced.
z Do not conduct the hareware hot-swapping operation with eletricity. (Except the hardware supporting hot-swapping)
z Change the damaged harddisk to insure the integrality of the record data(The infomation of the harddisk error is in the log)
Table of Contents
z 1 USB and 1 external SATA interface z Streams of one or more channels, Net DVR's running state and
z 16 alarm inputs and 4 relay outputs alarm state can be accessed through network
z Programmable for automatic display or recording of associated z Net DVR's parameters can be set through network
z Supports up to 8 SATA hard disks at the most z Streams can be recorded in a remote host PC.
z Privacy masks and multi-area motion detection z Files in Net DVR can be downloaded to or remotely played in a
z Easy installation on an existing network, no changes required z PC hosts can gain direct control of Net DVR's RS-232 or RS-485 port.
1
z Supports voice talk between host in surveillance center (back end)
and Net DVR (front end).
z Supports embedded web server. Browser can be used to access
Net DVR.
3. Storage Functions
z Supports 5 kinds of record trigger mode: Schedule mode, alarm
z Supports hard disk sleep mode. The last position in the part number indicates the HD information.
z Supports FAT32 file system.
z Switches quickly in PREVIEW mode; Note: The manufacturers would develop the hard disks with
z Supports privacy mask area; different performances to meet the different requirements of the
z Support view tampering area; target customers. Upon the selection of hard disks for DVR, those
z Supports local file Playback and playback by time, supports play industrial grade hard disks, used for large data storage and
fast, play slow, pause, play frame one by one, etc; long-time operation, will have priority. Unsuitable hard disks
z Supports position configurable OSD & LOGO; might cause the loss of system data after working for a certain
z Supports remote control; period of time. Please contact Infinova service personnel for
z Supports watermark. detailed information.
5. PTZ Control
z Supports Pan-Tilt-Zoom control and Preset through front panel,
keyboard, network and remote controller;
z Mouse control
6. Alarm Functions
z Supports Motion detect alarm, view tamper alarm, signal loss
alarm, exceptions alarm, etc;
z Supports setup of alarms calling up PTZ presets;
7. Others
z Supports RS-485 interface keyboard;
z User friendly menu interface
2
1.3 Front Panel Description
Front panel view
1
3 5 2 4 6
7
Figure 1-1
(1) Numeral keys and English letter keys are combined for input numerals, capital & small
Number key English letters and symbols etc.
2 Input key
【0】-【9】 (2) Under Preview status or PTZ control status, used to switch channels
Call up presets when using combinations of the numeric key and【PRST】key
3
(1)Used for PTZ Control, “IRIS-”
【IRIS-】 Control key (2)Used for “Motion Detect Area Setting”, set the whole picture as the motion detection area
(3)Enter “PTZ control” status
(1)Switch over between input methods (numeral, letter and symbol).
(2)Used for PTZ Control: “FOCUS-”
【*】 Control key
(3)Used for “Motion Detect / Privacy Masking / View Tampering Area Setting,” clear all setting
areas
(1)Switch among the videos display modes
【田】 Control key
(2)Used for PTZ Control: “FOCUS+”
【F1】 Reserved
Device switch, with electrical power indication. “Green” indicates that equipment is working;
5 Power switch Control key “red” indicates that device is stopped. When indication lamp is off, the power switch on back
panel is already off or power cable is disconnected.
Figure 1-2
4
No. Name Full Name Type Description
1 Power Switch Control key Power switching operation of DVR
2 DEV Device Control key Selection of controlled DVR according to device number
(1) Numeral keys and English letter keys are combined for inputting
numerals, capital & small English letters and symbols etc.
3 【0】-【9】 Number key Input key
(2) Under Preview status or PTZ control status, used to switch channels
(3) Call up presets
Enter into editing status, can also be used to delete the character in front
4 EDIT Edit Control key
of cursor
5 A Input Method Control key Switch over between input methods (numeral, English and symbol)
(1) Manual video recording
6 REC Video record Function key
(2) Under PTZ control status, call up presets
(1) Local playback
7 PLAY Video play Function key (2) When video playback, turn on/off the sound of the video
(3) Under PTZ control, start up auto-pan
System
8 INFO Function key Indicate DVR system information
information
9 VOIP Dialogue Function key Start up voice dialogue (Reserved)
10 MENU Main menu Function key Switch over from preview interface to menu operation interface
(1)Video split at preview, and switch over from operation interface to
11 田/PREV Multi-picture Control key preview interface
(2)Used for PTZ Control: “FOCUS+”
(1) Menu selection (【←】,【→】key), set option selection (【↑】,【↓】
keys)in the interface, 【ENTER】 key to confirm operation is in the
middle
← (2) Direction control under PTZ control
→ (3) Used for “Video playback”: 【←】: Backward;【→】: Forward;【↑】:
12 ↑ Direction key Control key Add play speed;【↓】: Reduce play speed.
↓ (4) Used for “OSD”, “Privacy Masking Area”, “View tampering”,
ENTER “Motion Detect Area”, adjust the location of the area.
(5) Used for “Privacy Masking Area”, “View tampering setting”, set the
size of the area.
(6) Used for “Input information”, press 【↑】or【↓】to enter edit status
(1) PTZ control
13 PTZ PTZ Function key
(2) Close iris
(1) Cancel the current operation, return to the previous menu
14 ESC ESC Control key
(2) Exit PTZ control status
15 Playback Playback Control key For pause and stop at playback
16 F1 F1 Reserved
Adjust aperture, focus and zooming at PTZ control
【IRIS+】
(1)Used for PTZ Control, “IRIS+”;
(2)Used for “Video Playback”, Start/pause duplicating segments;
(3)Used for “Privacy Masking Area Setting”, set the size of the area;
IRIS+ (4)Used for “View Tampering Area Setting”, set/cancel areas.
IRIS- (5)Used for “Motion Detect Area Setting”, set/cancel areas.
FOCUS+ (6)Used for “Input information”, enter edit status, delete the character in
17 PTZ control Control key
FOCUS- front of cursor, switch over in selection frame
ZOOM+ 【IRIS-】
ZOOM- (1)Used for PTZ Control, “IRIS-”
(2)Used for “Motion Detect Area Setting”, set the whole picture as the
motion detection area
(3)Enter “PTZ control” status
【FOCUS+】/【FOCUS-】: Used for FOCUS increase/ reduce
【ZOOM+】/【ZOOM-】 :Used for zoom in/ zoom out
Under PTZ control status, call up presets when using combinations of the
18 F2 F2
numeric key and【PRST】key
1. Load the battery into remote controller (2) Load batteries, make sure “+” and “-“ polarity is correct.
(1) Open the battery compartment cover of remote controller. (3) Close the cover.
5
Adjust brightness / contrast / hue / saturation
2. Start to use remote controller OSD display mode, adjust OSD Position
After DVR starts up and runs normally, press 【DEV】 on the Privacy Mask areas setup
remote controller, and input the “Device ID” (default is “88,” and Alarm in schedule
can be changed in “Display” menu) of the device to be operated. View Tampering, areas setup On screen warning
Further press 【Enter】 on the controller. If “STATUS” LED on the , handling method Audible Warning
device panel now turns green, it indicates that the remote controller Upload to center
that can be used for operation has selected this device. Trigger alarm out
Send Email
Note: The range of “Device ID” is 1-255.
Alarm in schedule
On screen warning
3. Stop using remote controller Signal loss, handle method Audible Warning
When remote controller selects device, press 【DEV】to turn off the Upload to center
“STATUS” light on the device panel and stop using the remote Trigger alarm out
controller. Send Email
MotionDetection Alarm in schedule
4. Use remote controller to shut down sensitivity, area setup, Record channel,
When remote controller selects device, press 【POWER】on the Motion detection alarm On screen warning
controller at least 3 seconds to confirm Power Off status. handling method Audible warning
Upload to center
Under the PREVIEW mode, a dialog box “requiring the password”
Trigger alarm out
shows up. Select the username and input corresponding password to Send Email
enter “Power Off” dialog box, select “enter” to shut down. (Note:
Use of “Power Off” button on the DVR rear panel is not allowed Copy function
before the “Power Off” indicator on DVR front panel turns red.)
Camera channel
The system will return to the preview video if authorization fails PTZ general parameter
after you input the password three times. PTZ Set preset points
Under the menu mode, the system will enter “Power Off” dialog Set sequence (unavailable)
box if the user has “Tool” operation authority. Select “enter” to shut Set cruise
down. If the user does not have “Tool” operation authority, then the Copy function
user has no right to normally shut down the device. Select Output
Preview mode
If remote controller does not work properly: Dwell time
(1) Check if it’s too far from remote controller to DVR Preview Audio preview
(2) Check if remote controller aims at the infrared port of DVR Alarm Auxout
(3) Check battery polarity Layout
Display delay
(4) Check if battery is running out of power
(5) Check if remote controller sensor is blocked Choose to overwrite or stop recording when hard
disk is full
(6) Check if there is any fluorescent lamp on nearby
SATA 1 Disk For
Note: If it still will not work, please change the remote controller; if Select Camera
it still cannot work, there is likely some problem with the infrared Camera Name
receiving part. Please contact the after-sales engineer. Record Para
Steam type
Resolution
Recording parameter setup Bit rate type
Max bit rate
Recording
Image quality
Frame rate
Enable Event Para
Enabe Rec;Schedule
Record schedule
Record Setup
Record trigger manner
1.5 Menu Description PreRec time
PostRec delay time
1.5.1 Main Menu Copy function
Select Alarm input、Alarm type
Main Menu Function options Record channel
Select camera Alarms Set alarm input schedule
Image Alarm input, Onscreenwarning
Camera name modify, Position adjust
handling method Audible warning
7
Upload to center
Trigger alarm out 1.5.2 Menu Description
Send Email
PTZ linkage The DVR has a menu with three levels. The first level is the main
Set alarm output schedule menu, a graphic interface with 12 icons shown in below figure.
Set alarm output delay time
Copy function
Exceptions type
Audible Warning
Exceptions handling method Upload to center
Exceptions
Trigger alarm out
Send Email
8
Provides a rectangle frame for inputting a character, Edit status can Chapter II Installation and Connections
be entered into by 【IRIS+】,【↑】 or【↓】. Following operation
can be done under editing status: Note: Please make sure the DVR’s power is disconnected before
(1) The types of characters input can be designated by 【*】key, connecting to any device.
including numerals, capital & small English letters, symbol.
(2) When input characters, press【0】numeric key to turn the page 2.1 Clear the Device and Accessories
of characters.
(3) Cursor can be moved by 【→】 and 【←】. When you receive the product, the following items are included in
(4) The character in front of cursor can be deleted by 【IRIS+】. the carton:
(5) Press 【ENT】 key to temporarily save and exit the editing (1) A Embedded Network DVR
status; press 【ESC】 key to cancel the entry and exit the editing (2) A User’s Manual
status. (3) A CD
(4) A Remote Controller
4.Button (5) A DB9 to RJ45 cable
For execution of a specific function or enter into the next menu. For (6) A SATA DMA66 Hard Disk cable (Long)
example, Button “ENT” executes the functions of data saving and (7) Eight SATA DMA66 Hard Disk cables (Short)
returning to previous menu, “Adjust” button enters into next menu. (8) A Power Supply cable
Some buttons are in dark colors indicating that the control items of (9) A USB cable
the buttons are currently invalid and can’t be operated before (10) Some Screws
exiting. The main menu actually is made up of 12 groups of buttons
with icon marks. The function of each button is to enter the next Note: Different DVR models have different accessories. Please
menu. refer to the “Consignment list” for detail.
Operation hint: In this user manual, various “Buttons” on the 2.2 Install Hard Disk
DVR front panel are expressed as “Button Names”. For example,
preview key is expressed as 【PREV】; and hard disk indicator is 1. Installation Hint
expressed as【HDD】. The names are the same as those in the menu Disassembly of the housing and installation of hard disks must be
interface, e.g., ENT button is expressed as “ENT”. performed by professionals. Before adding drives, please calculate
total capacity of hard disk required by each DVR according to
video recording parameters.
2. Installation Tool
One Philips head screw driver.
3. Install Hard disk
(1) Open the housing.
(2) Install hard disk.
DVR has 8 SATA hard disk interfaces:
For V3013A, 8 interfaces are available;
For V3013W, only 4 interfaces are available.
(3) Remove the hard disk bracket.
(4) Put the hard disk into the bracket and fix the hard disk with screw.
(5) Install the bracket back into the device and fix it onto the
device with screw.
(6) Connect the hard disk data cable.
(7) Connect the hard disk power cable.
(8) Replace the cover of the housing and fix with screw.
Reference file:
Calculate total capacity needed by each DVR according to video
recording (video recording type and video file storage time).
The formula is shown as follows:
qT = 3600÷8÷1024÷1024×N×di×hi×Di
9
In the formula: Di :means number of days for which the video shall be kept
qT :means HD total capacity, unit GB (byte) For example, one DVR has the following parameters:
N : means total number of channels in one DVR d i =768Kbit/s, N=8, hi =24h, Di =30
d i :means the bit rate,unit Kbit/s qT = 3600÷8÷1024÷1024×8×768×24×30=1898 (GB)
hi :means the recording time for each day(hour) So the total capacity 1898GB is required.
10
2.3.2 V3013 (Looping Models)
Figure 2-1-2.(V3013-16L)
10
2.4 Alarm Input/Output Connection Method
Introduction
Figure 2-2
Figure 2-3
G (GND): “Alarm Output” GND port, every output port and the
corresponding alarm output device shared the GND.
1-4: can connect 4 alarm output devices respectively.
If there is an alarm, 1/2/3/4 will connect with the corresponding Figure 2-5. The corresponding relationship of twisted cable
GND, to activate lamp/light/sound. There are four jumpers, JJ1, JJ2,
JJ3, and JJ4, for selecting the alarm output method. 2.6 RS-232 Connect Cable Made Method
The 4-alarm output relays are default closed at the factory. The 1. Material and tool
above introduction is to this output method. If to disconnect the One twisted cable (8 pins), one standard RJ45 connector, one or
jumper, the 4-alarm output just likes 4 switches. If there is the alarm, more DB25 or DB9 plug-in, a special tool for RJ45, one soldering
the corresponding switch will on. iron, and some soldering tin.
It is suggested the alarm output switch is used within 12V/1A range.
2. Pin definition
2.5 UTP Network Connect Cable Made Method
To make the RJ45 according to the following pin definition; I means
1. Material and tool DVR input, O means DVR output.
1 twist cable (8 pin, the length can be defined according to the Pin No. Name I/O Description
actual demand, but less than 100m), 2 standard RJ45 connectors, 1 1 DCD I Carrier Detect
special tool for RJ45. 2 RxD I Receive data
A network cable test tool to test each cable made is suggested. 3 TxD O Transmit
2. Pin definition 4 CTS I Clear data
To make the network cable according to the actual requirements, 5 RTS O Request to send
there are two situations as follows: 6 DTR O Terminal device is ready
(1) Use the following method to make the network cable when 7 GND GND
DVR is connected with HUB or the network switcher: 8 Empty — —
DB9 is 9-pin connector; and DB25 is 25-pin connector. According
to the connector types, DB9 or DB25 can be divided into male type
connector and female type connector. Therefore there are four types
of connectors. Please refer to the figures below for details:
11
1 5
6 9
5 1
9 6
Figure 2-11. The connect fig for RJ45 and DB25 (DTE)
1 13
(2) When the serial port of the DVR is connected with DTE(Data
Terminal Equipment) with DB9 plug-in, the corresponding
14 25 relationship is as follows:
13 1
25 14
Figure 2-10
12
(3) When the serial port of DVR is connected with DCE (Data Chapter III Basic Operation Guide
Communication Equipment, like MODEM), one end of the
cable is 8-pin RJ45 plug-in, the other end is DB25 pin plug-in, There are various kinds of status reported by the system:
the corresponding relationship is as follows: (1) Preview Status
(2) Menu Setup Status
(3) Manual Recording Status
(4) Playback Status
(5) PTZ Control Status
Entering and switching between the above status indications can be
accomplished by pressing the keys.
Note: In default mode, there is “Ting” when pressing the keys each
time after the system starts up. Press 【MENU】and hold it for over
three seconds to cancel the “Ting” produced by the system (Set
“Mute” mode).
3.2 Preview
1. Enter Preview Status
(1) DVR enters the preview interface automatically after
start-up.
(2) Enter the preview interface from “Menu Setup”: Press【田】
(3) Enter the preview interface from “Manual Recording”: Press
【ESC】or 【田】
(4) Enter the preview interface from “Playback”: Press【ESC】
to enter “Playback Search” status, and then press【ESC】or
【田】
(5) Enter the preview interface from “PTZ Control”: Press
【ESC】or 【ENT】
Preview image is showed in the figure below:
13
Note: If users don’t set corresponding parameters of CRT monitor
correctly, it will not display the hint to status lamps in the image
fully. Please consult Infinova customer service professional for
detail.
14
If username and password are both correct, the following menu 3.4 PTZ Control
appears (main menu):
Note: Operators shall have “PTZ control” operation authority rights.
The setting of PTZ parameters should be performed prior to PTZ
Control. Please refer to “4.17PTZ” for details on how to set PTZ
parameters.
Figure 3-3
Figure 3-5
Step two: Enter the “Pass” setup interface.
Use 【→】or【←】 to move “Activity Frame” to “User” in menu.
When the cursor is in the field of “User”, use direction keys 【↑】 、
Press 【ENT】 to access the User Setup Interface (Note: Only those
【↓】 to select your username, move the cursor to the field of
users excluding the administrator can have access to the menu for
“Pass” using 【→】key, use 【IRIS+】 key to delete the numbers
password setting and modification. For details on administrator’s
before the cursor, and press “ENT” after the entry is finished. Move
modifying password, please refer to “4.2 Add and delete users”).
cursor to “confirm” and press 【ENT】on front panel. If there is a
warning buzz, it indicates that you may have input an incorrect
password, and the cursor will automatically move to the field of
“Password”. You can input again. The system will return to the
preview image after three password failures.
If the user has no authority for the PTZ Control, the system will
indicate that the user has no authority for PTZ operation after the
correct username & password are entered and “ENT” button is
pressed.
Figure 3-4
15
【STATUS】 indicator does not turn red, STATUS】 indicator
can be lit and turned red by pressing 【PTZ】 key again.
(2) When calling presets, the numeric keys should combine with
【PRST】 key. Otherwise,pressing the numeric keys only
would switch the video channels.
(3) Under “PTZ Control” status, other keys that have nothing to do
with PTZ Control become invalid, e.g.,【MENU】 key.
“PTZ control ” in the image indicates that the unit is under “PTZ Note: Operators shall have “record” operation authority rights.
control” status. The date “12-20-2004 Mon 15:08:02” in the image Before recording, please make sure there is hard disk space for
means the current date. Users could decide whether to display it in saving the data in the device, or please contact administrator.
the image or where it is by default (see “4.6 System Time”). 1. Enter Manual Recording
“Camera 01” means the current image from the No. 1 video channel. Under the “PREVIEW” mode, press 【REC】 key on the front panel,
Users can decide whether to display in the image or where it is by and you will be prompted for your username and password.
default (see “4.7 Camera Name”).
If 【STATUS】 indicator lights up and turns red, the unit is already
under PTZ Control status. If the screen displays "PTZ control", then
the 【STATUS】 indicator does not turn red, 【STATUS】 indicator
can be lit and turned red by pressing 【PTZ】 key again.
16
If username & password are correct, the operation authority is status list and channel indicator lights in the front panel turn to
available, and the operation is correct, then press “Confirm” to green or orange.
access the “Manual Record” interface: Note: If all the video channels are recording, the “Stall all” will turn
grey and not available.
Stop All
No matter what the status of each channel is, all channels will be
stopped after executing “Stop All”. You can use【←】or 【→】key
to move the cursor to “Stop All” button and press 【ENT】 key in
front panel to stop the record in all channels. At this time the status
list indicator lights is “ ”or red, the channel indicator light in front
panel turns off or to red.
Stop Recording
In“Start/Stop”, press【←】 【→】key to move the active box to where
、
the video channel is started. If “Start/Stop”is marked with“9”, this
means the channel is not recording, and there is no need to stop Figure 3-11
recording. If “Start/Stop”is marked with“×”, press 【ENT】 key or
【IRIS+】 key to switch to “9”, and the correspond status light When the cursor is at the field of “User”, use direction keys 【↑】 、
turns to “ ” or red, at the same time the status light in front panel 【↓】 to select your username, move the cursor to the field of
will turn off or turn to red. “Pass” using 【→】 key, use 【IRIS+】 key to delete the numbers
before the cursor, and press “Confirm” after the entry is finished.
Start All Move cursor to “Confirm ” and press 【ENT】on front panel. If there
No matter what the status of each channel is, all channels will begin is a warning buzz, it indicates that you may have input an incorrect
to record after executing “Start All” button. You can use【←】 or password, and the cursor will automatically move to the filed of
【→】 key to move the cursor to “Start All” button and press “Pass”. You can input again. The system will return to the preview
【ENT】 key in front panel to start recording in all channels. The image after three password failures.
17
If the user has no authority for Playback, the system will prompt 【↓】key. The default is “1”.
that he/she has no authority for Playback after the correct username Second Channel: While playing back the displayed videos in the
& password are entered and “Confirm” button is pressed. main channel, play back the recorded videos in the second channel.
Choose via 【↑】, 【↓】 key, and the default is “None”. If Channel
1~16 have both recorded, select “1” for the main channel “Chan”,
and one of the rest for the submain channel “Second”, and select the
appropriate file type and time slot, and then press “Search”, the
search result will be listed as show in the following figure:
Figure 3-12
Figure 3-15
The selected file will play by first selecting from the video file list
and pressing【ENT】 key. As demonstrated in the figure below: the
main channel “Chan” on the left, the submain channel “Second” “2”
on right.
Figure 3-13
There are four options for Save Device: USB DISK, USB HD, USB Figure 3-16
CD/DVDRW and SATA CD/DVDRW, SATA HD.
If the second channel has no videos as the main channel records,
2. Playback Search Operation then it simply does not display the second channel as it plays the
If you want to find the record files in the first channel today, this is main channel.
very convenient. You can press 【ENT】 key and find the recording Note: “PLAY” supports four images synchronous preview.
file information in the list frame. “No File Found” will be indicated (1) File Type: Indicates under what circumstances the video files
if there are no files you are searching on the hard disk. to be searched are recorded. The options include: Motion
Detection (“Mot. Det.”), Alarm, Manual, All, All Time. Please
refer to “4.12 Motion Detect Setup”, “4.15 Alarm Parameters
Setup”, and “3.5 Manually Recording”. Choose via 【↑】,
【↓】key. The default is “All”.
(2) Time Period: Indicates a time period to search. Input the
start/ending time through numeral keys (Time format “Year-
Month-Day Hour: Minute: Second”). The default is the
current date.
Figure 3-14 (3) Card Number: input card number through the front panel. The
number is a series of characters that are added to pictures
You can find recording files through different methods: through the network or serial ports (they can be numerals,
Channel No: Select the channel (main channel) to search via 【↑】, capital & small characters). This option is used for recording
18
card number exchanges with ATMs. The transaction (2) Playback by time: Validate time search (“9”is OK,
information relating to the card number should be set before default) using 【IRIS+】 or 【ENT】 key, move the
searching the video file. Please refer to “4.20 Transaction cursor to the filed of “Playback by time” using 【←】
Information”. or 【→】 key. Press 【ENT】 key to start playing the
recorded files from the starting time (accuracy of to one
3. Playback Method second). If there is no recording file in the start time, it
In the following we introduce three kinds of playback method for will find the next one. If there is no recording in this
you to choose. time period, “failed operation” will appear.
(3) Search Card number, playback file: Enter the card
(1) Time Search, File Playback: Input the start/ending time, press number to validate card number search (“9”is OK,
【IRIS+】 or 【ENT】 key to enable Time Search (Mark it as default) using 【IRIS+】 or 【ENT】 key, and select
“9”), move the cursor to the field of “Search” using 【←】 “Search” button. All the recording files matching the
or 【→】 key, and press 【ENT】 to search files. The recorded conditions will be listed (Note: The files could reach a
files matching the conditions will be listed (Note: The files can maximum of 400; page-turning can be done through
reach a maximum of 400, page-turning can be done through “Selecting page number”. If the files exceed 400 in the
“Selecting page number”. If the files exceed 400 in the entered entered interval, you need to adjust the starting interval),
interval, you need to adjust the starting interval), use【↑】or use 【↑】 or 【↓】 key to move the scroll bar on Play
【↓】key to move the scroll bar on Play Back, and press Back, and press 【ENT】 key on the front panel to start
【ENT】 key on the front panel to start playing). playing.
4. Operation in playback
If a submain channel is selected, the main channel will contact the
submain channel through time sync method. The operations during
the playback will be invalid for these four channels.
The operation of single channel playback is the following:
Figure 3-17
Figure 3-19
19
【ENT】 key to continue. In single frame mode, every press of
【ENT】 key plays one frame forward.
Use 【IRIS+】 key to copy segment, and can copy a maximum of 30
segments each time. The file or the segment can be copied to the
designated device via USB or SATA interface. There is a detailed
introduction in the recording files backup, please refer to “3.7
Backup Record File”.
Press【ESC】 key to exit the play video. After it finishes, it will exit
playback automatically.
Figure 3-21
Note: If there are other operations (such as recording) performing
during playback, the actual playing speed cannot reach 8 multiples. When the cursor is at the field of “User”, use direction keys 【↑】 、
【↓】 to select your username, move the cursor to the field of
5. Reserve Record Files from HD to Writer “Password” using 【→】 key, use 【IRIS+】 key to delete the
Press 【PLAY】 key on the front panel, set the parameters of numbers before the cursor, and press “Confirm” after the entry is
channel, time and so on. Click “Search” and the appropriate files finished. Move cursor to “Confirm ” and press 【ENT】on front
will be shown in the list. Select the file you want to save and press panel. If there is a warning buzz, it indicates that you may have
【IRIS+】 key on the front panel. Select “SATA CD/ DVDRW” in input an incorrect password, and the cursor will automatically move
“Save Device”, and then click “Copy” to reserve. to the filed of “Pass”. You can input again. The system will return to
the preview image after three password failures.
If the user has no authority for Playback, the system will prompt that
he/she has no authority for Playback after the correct username &
password are entered and “Confirm” button is pressed.
Figure 3-22
Figure 3-23
20
2. 2. Backup file file playback interface, and start up playback;
Select or input channel no., file type and start & stop time (or card (3) Press 【IRIS+】 to set the starting mark for the backup segment,
number) of backup files, execute the “Search” to list files that meet and press 【IRIS+】 again to set the ending mark for the
with the conditions. Please refer to “3.6 Playback” for details on backup segment.
how to search. (4) Repeat step 3 to edit multiple segments (up to 30).
Note: Max 400 files are listed. To turn the pages use “ Page Press 【ESC】 key after the marking is done. The system will
selection”. If the files are more than 400, please change the start and prompt you whether backup is needed. Select “Confirm” to copy the
stop time. selected segment into the designate device, and select “Cancel” not
to copy. You will be advised backup was successful after the backup
is finished. Please check if the backup device is connected tightly
and USB and power supply is normal if you see the message box
below:
Figure 3-26
Select the file to be backed up in the file list (turn the pages by 3.8 Voice Dialogue
using the “ Page No”, use 【↑】, 【↓】key to move the scroll bar, use
【PTT】(or 【VOIP】for remote controller) function is reserved at
【IRIS+】 key to switch and select the file as backup file or not,
present. It can be realized at client PC. Please refer to “Client
mark the file with“9.”
Software for V3013 Embedded Network DVR” manual for detail.
Then select “Save Device” and execute “Copy” in the menu to copy
the files. The message “copy successful” will appear after copying
is completed. 3.9 Power Off
After the execution of “copy” option, if you find the following
Note: Please shut down the DVR correctly. The HDD will be
message, please check USB backup device’s connection, power
damaged if the DVR is not shut down correctly (especially while
supply is normal, etc.:
recording). The correct methods are using the “Power Off” button in
the menu, or the 【POWER】 key in the front panel, or the
【POWER】 key in the remote controller.
Note: During the file backup, do not remove USB from DVR.
21
wrong password, and the cursor will automatically move to the filed NOTE: The system will enter “Power Off” dialog box if the user
of “Pass”. You can input again. The system will return to the has “Tool” operation priority. Select “Confirm” to shut down. If the
preview image after three password failures. user does not have “Tool” operation priority, then the user has no
If username & password are correct, the operation authority is right to shut down the device.
available, and the operation is correct, then press “ENT” to access
“Menu Operation” interface: (2) Through 【POWER】 key in the DVR front panel or in
remote control
Press the 【Power】 Switch on the front panel or the remote control
under the PREVIEW mode and hold it for three seconds, and you
will be prompted for the username and password.
Figure 3-31
When the cursor is at the field of “User”, use direction keys 【↑】,
【↓】 to select your username, move the cursor to the field of
“Pass” using 【→】 key, use 【IRIS+】 key to delete the numbers
Figure 3-28
before the cursor, and press “Confirm” after the entry is finished.
Move cursor to “Confirm ” and press 【ENT】 on front panel. If
Move the cursor to “Utilities” using【←】or【→】key, press “ENT” there is a warning buzz, it indicates that you may input a wrong
to enter “Utilities” interface: password, and the cursor will automatically move to the filed of
“Pass”. You can input again. The system will return to the preview
image after three password failures.
If username and password are correct, the operation authority is
available, and the operation is correct, then press “Confirm” to enter
the Power Off dialog box:
Figure 3-32
Figure 3-29
Select “Confirm” to shut down.
Select “SYSTEM SHUTDOWN” on “Utilities” interface to enter the If username and password are correct, and the operation is correct,
Power Off dialog box using【←】or 【→】key, and press “Confirm” to then press “Confirm” to shut down. (Note: It’s not allowed to press
shut down. “Power Switch” in the back panel before the power LED turns red.)
The system will return to the preview image after three password
failures.
22
Chapter IV System Configuration
Figure 4-2
2. Change Password
Move cursor to “User”, press【ENT】to enter into “user” interface.
Figure 4-4
23
4.2 Add and Delete Users
1. Enter
Press 【MENU】 key to enter “Menu Operation” interface under the
PREVIEW mode, move the cursor to “User” using 【←】 or 【→】
key.
Figure 4-7
The new user’s password can be set here, or set by users themselves.
If there is no password for the newly added user, then the user
password should be blank. The added user’s password can be
changed through this method.
Figure 4-5 Note: The maxium length of user password is 16 bits.
Press 【ENT】 key on the front panel to enter “User” menu interface.
You can add/delete users and assign the corresponding authorities in 3. Assign Right
the “User” menu interface. Assign right to the newly added users or adopt the default right. The
right could be reassigned later. Follow the steps below to set right.
2. Add User
Move Cursor Box to “Set Right” press 【ENT】 key to enter
“Set Right”interface:
Figure 4-6
Select “Add,” input the new user’s name in the popup dialogue
frame, select “Confirm,” and the new user’s name becomes Figure 4-8
effective. The “User” interface returns. Using the same method you
can add multiple users, max 16 users (including administrator). New user’s operation authority can also be made (“9” indicates
operation authority is available, “×” indicates operation authority is
not available. Switch by pressing 【IRIS+】 or 【ENT】in front
panel).
24
(1) “Local Authority” Introduction:
PTZ Ctrl: PTZ Control, including direction adjustment, iris+/-,
zoom+/-, focus+/- or preset call-up;
Record: Enable manual recording;
Play:Search the video/audio file saved in hard disk and play,
and backup the file to external device through USB
SetPara: Set parameters
Log: Search the log file
Util: System operations including Saving parameters,
Resuming Parameters, System upgrade, Hard disk
management.
Hint: Follow the steps below to obtain the MAC of the PC.
Step one: Open Windows simulated terminal. Click “Start” “Run”,
if the operating system is Windows2000/WindowsXP,
enter “cmd”.
Step two: Enter “ipconfig/all” in the simulated terminal and press
“Enter.”“Physical Address”in the results can be seen,
where the MAC of PC is displayed. If “ Physical
Address” is not displayed after the command is entered,
please check whether the network card of the PC is out of
order.
4. Delete User
Select user’s name to be deleted from user’s name list (using 【↑】 Figure 4-11
【↓】 keys), then press “Del.”
Press 【ENT】 key on the front panel to enter “Display” menu
interface.
25
Note: It’s suggested to reboot the DVR after change the “Video
Standard”.
Figure 4-12
Figure 4-13
2. Change Unit Name
Move the cursor to “Unit name” using 【←】 o r【→】 key, and
press 【IRIS+】 key to edit “Unit Name”. The system default Note:
name is“Embedded Net DVR”. Press “Numeric” keys to enter Video Standard: the setting PAL/NTSC format must conform to the
numbers, English characters (Upper case, Lower case) and symbols, format of the connected camera, otherwise the images displayed
press 【*】 to switch among numbers, English characters (Upper will be abnormal, such as “black stripes,” “snowflake” and
case, Lower case) and symbols, press【0】numeric key to turn the “shadow.”
page of characters, press【IRIS+】 key to delete the characters Device ID: Users can enter the device ID number via the remote
before the cursor. Press 【ENT】 key to temporarily save and exit controller to control the desired device when controlling multiple
the editing status; press 【ESC】 key to cancel the entry and exit the devices using one remote controller. The device ID number ranges
editing mode. from 1 to 255.
Require Password: if the operation password is used, password
input is required to enter other interface from the preview image; if
3. Change Unit Number
the operation password is not used, password input is not required to
Move the cursor to “Device ID” using 【←】 or 【→】 key, and
enter other interface from the preview image. The default user is the
press 【IRIS+】 key to edit “Device ID.” The system default device
administrator.
ID is “88.” Press 【numeric】 keys to enter numbers, and “Device
Screen Saver: Set a period of time, during which the system will
ID” ranges from 1 to 255. Press 【IRIS+】 key to delete the
automatically exit Menu Setup and return to “Preview” without any
characters before the cursor. Press 【ENT】 key to temporarily save
operation. Setting “Never” indicates that the menu interface never
and exit the editing mode; press 【ESC】 key to cancel the entry and
automatically exits.
exit the editing mode.
Unit number is used when controlling DVR with the remote control. 4.5 System Time
Unit number should be entered into the remote control before Reset the date and time of the system, set the display mode of date
controlling the DVR that the unit number represents. Please refer to & time (transparent, blinks) and adjust their Position in the image.
“1.4 Remote Control Description” for details on how to use a
remote control to control DVR.
Calibrate System Time Manually
Press “Confirm” to save the revision, and press “Cancel” or 【ESC】 DST: Users could set DST to adapt to the local time transformation.
key to exit without saving.
.
26
Date Format: Month-Day-Year
Time Format: Hour-Minute-Second
Figure 4-14
Note: When DST is enabled, set forward the clock for 1h; when
DST is disabled, set backward the clock for 1h.
If the period is set incorrectly, the warning dialogue box will be
prompted, shown as below:
Figure 4-17
Figure 4-18
27
characters, press 【IRIS+】 key to delete the characters
before the cursor.
Step three: Press 【ENT】 key on the front panel to exit editing
after the camera name is entered.
Repeat above steps to input other camera names.
After defining the camera name, press “Confirm” button. The new
camera name will be saved. You can see that the new camera name
is added onto the image of relevant camera. If you press the
“Cancel” button or 【ESC】 key, you will cancel the camera name
definition.
3. Set the display position of the camera name and the OSD
You can set the display position of every camera name. In actual
usage, you only need to set the position of one camera name, then
copy it to other cameras. Figure 4-19
28
Figure 4-21
Figure 4-20
2. Enable “Privacy Mask”
Select one channel, move the cursor to “OSD”, and select one of the Switch “Privacy Mask” option status to “9” through 【IRIS+】 key,
five options: Opaque & Steady (default), Opaque & Flashing, to enable the Privacy Mask function.
Transparent & Steady, Transparent & Flashing, No Display. Users
can select one of the options according to their own requirements.
Move the cursor to “Position”, press “Confirm” to enter the
“Position” operation interface in “OSD”, and OSD date and time
display on video image. Adjust the OSD in the image using 【↑】,
【↓】, 【←】, 【→】 keys, and switch over the date and time format
using 【IRIS+】 key. Press 【ENT】 key on the front panel to save
the setting and return to “Image” menu, or press【ESC】key to exit
without saving.
Figure 4-23
29
4. Adjust the area
The upper left frame is the Privacy Mask setup frame. The entire
picture is segmented into frames for easy setup. If PAL format is
selected, the frames should be 22×18. If NTSC format is selected,
the frames should be 22×15. First move the activity frame to the up
left of the area to be masked. Press 【IRIS+】 to set, press direction
key to adjust the size of the area: 【↓】 is enlarging downward,
【↑】 shrink upward, 【→】 enlarge to right, 【←】 shrink to left.
Press【*】to clear all setting areas.
Four privacy mask areas can be set in any single channel. The
minimum size is one pane, and the maximum is 8 X 8 panes.
Press【ESC】key to cancel the area setup. Press【ENT】after returning
to “Image” interface. Execute “Confirm” in menu to save the privacy
mask settings, or choose “Cancel” to cancel the setup. If the setup is Figure 4-25
successful, the preview of the channel will appear as follows:
2. Run View Tampering
There are four options for the View Tampering: close, low, normal,
high. You can select low, normal or high to active the View
Tampering area setup and process functions.
Figure 4-24
Note: To cancel the area setup, simply set “Privacy Mask” as “×”
through 【IRIS+】or 【ENT】 key.
Figure 4-26
4.10 View Tampering Setup
If the camera view is being blocked maliciously, an alarm signal can 3. Set View Tampering Area Method
be generated. The View Tampering function is must be set through Enter into View Tampering Area Setup interface to setup View
these steps: Enable mask alarm, set region, set mask handle method. Tampering area.
Figure 4-27
30
The upper left activity frame is the View Tampering area setup been armed (even there is no setting of the “Remote Host IP
frame. The entire image is segmented into frames for easy setup. If address” and “port” of the client PC in the DVR), and as the
PAL format is selected, the frames should be 22×18; If NTSC alarm occurs in the system, the client software can also receive
format is selected, the frames should be 22×15. Move the activity the alarm signal.
frame to the upper left of the area to be masked. Press 【IRIS+】 to Trigger Alarm Out: Output the alarm signal from the alarm
set, press direction key to adjust the size of the areas: 【↓】 is output port when receiving alarm.
enlarging downward,【↑】 shrink upward, 【→】 enlarge to right, You can select one or more handling methods. After the setup, select
【←】shrink to left. Press【*】to clear all setting areas. “Confirm” and return to “Image” setup interface. Then execute
Only one View Tampering area can be set in any single channel. The “Confirm” in “Image” setup menu to save the parameters. Select
minimum is one pane, and the maximum is full screen. “Cancel” or press 【ESC】 key in front panel to cancel the set
Press 【ESC】 key to cancel the area setup. Press 【ENT】 after parameters.
finishing to return to “Image” interface. Execute “Confirm” in the Note:
menu to save the view tampering settings, or choose “Cancel” to (1) To trigger one or multiple alarm outputs, select the
cancel the setup. corresponding alarm outputs.
(2) To cancel the mask alarm process, set “View Tampering” to
“Off.”
4. Set alarm handling method
Enter into “Method” of mask alarm. The handling method can be
4.11 Signal Loss Setup
defined in “View Tampering Handle” interface.
The unit will alarm when the video signal of the video channel lost.
Refer to the steps below for detailed video loss alarm and handling.
1. Enter Menu Operation
Press 【MENU】 key to enter “Menu Operation” interface under the
PREVIEW mode, move the cursor to “Image” using【←】 or 【→】
key, and press 【ENT】 key on the front panel to enter “Image”
menu interface.
Figure 4-28
Alarm in Schedule: Select date first, then set time segment. Time
segment is set sequentially. Segments cannot overlap and no nesting
is allowed. After the precaution time of a day is set, the parameters
already set can be copied to other dates.
Figure 4-29
Handle Method includes:
On Screen Warning:Switch automatically to the alarming video
Select the camera using 【↑】 or 【↓】 key;
channel.
Audible Warning:Sound beep when alarm occurring.
2. Active Signal Loss Process
Upload to Center: Transmit the alarm signal up to the network
Move the cursor to “Signal Loss”, select “Handle” using 【↑】 key
when alarm occurred, and the client PC terminal can get the alarm
to activate “Method” button.
signal through the DVR client software via network. There are two
upload methods:
(1) “Passive monitor” at client PC: If the “Remote Host IP
address” and “port” of the client PC in the “Network” interface
have been set in the DVR (even arm is not set at the client PC),
and as the alarm occurs in the system, the client software can
also receive the alarm signal. For details of network setup,
please refer to “remote host and its port” description of “4.16
Network parameter”.
(2) “Active upload” at client PC: If the client software in PC has
31
(2) “Active upload” at client PC: If the client software in PC has
been armed (even there is no setting of the “Remote Host IP
address” and “port” of the client PC in the DVR), and as the
alarm occurs in the system, the client software can also receive
the alarm signal.
Trigger Alarm Out: Output the alarm signal from the alarm
output port when receiving alarm.
You can select one or more handling methods. After the setup, select
“Confirm” and return to “Image” setup interface. Then execute
“Confirm” in “Image” setup menu to save the parameters.
Figure 4-31
Alarm in Schedule: Select date first, then set time segment. Time
segment is set sequentially. Segments cannot overlap and no nesting
is allowed. After the precaution time of a day is set, the parameters
already set can be copied to other dates.
Handle Method includes:
On Screen Warning:Switch automatically to the alarming video
channel.
Audible Warning:Sound beep when alarm occurring.
Upload to Center: Transmit the alarm signal up to the network
when alarm occurred, and the client PC terminal can get the alarm
signal through the DVR client software via network. There are two
upload methods:
(1) “Passive monitor” at client PC: If the “Remote Host IP Figure 4-32
address” and “port” of the client PC in the “Network” interface
have been set in the DVR (even arm is not set at the client PC), 2. Activate Motion Detection
and as the alarm occurs in the system, the client software can Move the cursor to “Motion Det Level” using 【←】 or 【→】 key.
also receive the alarm signal. For details of network setup,
please refer to “remote host and its port” description of “4.16
Network parameter”.
32
The upper left white frame is the motion detect area setup frame, the
entire image is segmented into 22*18 (For NTSC format camera, it
is 22*15) panes. The maximum area is full screen and the minimum
is one pane. Use the following operation keys for motion detection
area setup:
【↑】 【↓】 【←】 【→】: Move the “white frame” to any place
【IRIS+】: Switch between white frame and red frame (motion
detection area)
【IRIS-】: Set the whole picture as the motion detection area
【*】: Clear all the areas set
【ENT】: Finish setup, save and return to “Image” setup interface
【ESC】: Cancel the setup and return to “Image” setup interface
Note: Move the white box to any position and press 【IRIS+】 key
to set the area in the white box as the motion detection area. Any
Figure 4-33 motion in the set area will trigger an alarm. Press 【IRIS+】 key
again to cancel the setting.
There are 6 motion detection levels ranging from 0 to 5. Level 0 is The figure below shows a sample setting:
the lowest and level 5 is the highest. Select “Off” to disable
motion detection.
Figure 4-36
33
Move cursor by using 【←】 or 【→】 direction keys, use 【ENT】 4.13 Local Monitor Preview Properties
or 【IRIS+】 key to select.
Set triggering channels to record or preview and select one or more “Preview ” is used to set auto switch from one image to the next.
alarm modes. Users can also set Preview Mode, dwell time, Audio preview and
Layout.
34
(2) Set “Audio Preview” to monitor the sound of the channel. Bit rate: 32K, 48K, 64K, 80K, 96K, 128K, 160K, 192K, 224K,
When the preview interface is the single-image preview of the 256K, 320K, 384K, 448K, 512K, 640K, 768K, 896K, 1M, 1.25M,
channel, you can monitor the sound. 1.5M, 1.75M, 2M, user-defined.
(3) Key “Wide” on front panel could be used to shift between Image Quality: Highest, Higher, High, Average, Low, and Lowest.
“Main Chan” and “Aux Chan” Frame Rate: 25(PAL)/30(NTSC), 20, 16, 12, 10, 8, 6, 4, 2, 1, 1/2,
1/4, 1/8, 1/16.
4.14 Recording Schedule Setup Note: Under the same bit rate, the lower the frame rate is, the better
image quality is.
The DVR provides scheduled recording. PreRecord Time: Records images prior to the alarm trigger. The
options are: NoPreRecord, 5s, 10s, 20s, 25s, 30s, Max PreRecord.
1. Enter Recording Operation Menu Note: Please reboot the DVR to make the parameters effective if
Press 【MENU】 key to enter “Menu Operation” interface under the you modify the PreRecord time.
PREVIEW mode, move the cursor to “Recording” using 【←】 or Record Delay: Post-alarm recording. The options are: 5s, 10s, 30s,
【→】 key, and press 【ENT】 key on the front panel to enter 1m, 2m, 5m, 10m.
“Recording” menu interface. Note: Reboot the DVR to make the parameters effective if you
modify the Record delay.
Note: If Hard Disk is full, select “Overwrite” to write over the
previously recorded files. If you select “Stop Recording,” the Hard
Disk needs to be cleared when it becomes full.
3. Recording schedule
“Recording schedule” sets the exact day and time the unit begins to
record and the triggering condition for recording.
Figure 4-39
35
All day (24 Hours) record setup steps:
(1) Switch “All Day” to “9” status by using 【ENT】 or 【IRIS+】
key.
(2) Select one record type. The options are: All Time, Alarm,
Mot/Alm, Mot & Alm, Mot Det.
(3) In “Copy to” option, select a day, press “Copy” button to copy
the current parameters to the other day. You can skip this step if
you do not want to copy.
(4) Press “Confirm” button.
Figure 4-42
36
Alarm In Schedule: activation when there is an alarm in the 4. Set PTZ linkage
designated time segment. If PTZ Linkage is set, the PTZ linkage camera will automatically
Handle Method includes: switch to the corresponding preset when an alarm occurs during the
On Screen Warning:Switch automatically to the alarming video armed period.
channel. In the “Alarms” setup interface, click on “PTZ linkage” button and
Audible Warning:Sound beep when alarm occurring. press 【ENT】 to enter into “PTZ linkage” setup interface:
Upload to Center: Transmit the alarm signal up to the network
when alarm occurred, and the client PC terminal can get the alarm
signal through the DVR client software via network. There are two
upload methods:
(1) “Passive monitor” at client PC: If the “Remote Host IP
address” and “port” of the client PC in the “Network” interface
have been set in the DVR (even arm is not set at the client PC),
and as the alarm occurs in the system, the client software can
also receive the alarm signal. For details of network setup,
please refer to “remote host and its port” description of “4.16
Network parameter”.
(2) “Active upload” at client PC: If the client software in PC has
been armed (even there is no setting of the “Remote Host IP
address” and “port” of the client PC in the DVR), and as the
alarm occurs in the system, the client software can also receive
the alarm signal.
Figure 4-43
(3) Trigger Alarm Out: Output the alarm signal from the alarm
output port when receiving alarm.
Select PTZ linkage channel first. Enable Preset, Sequence, or Cruise
In the “Alarm In Handle” setup interface, you can setup many
and input the number of preset, sequence respectively (the
related parameters including alarm input effective time, trigger
parameters of preset, sequence and cruise are set in “PTZ” setup
channel to record and preview, trigger alarm output, etc.
interface). Each of them can use 16 numbers.
Set alarm trigger channel: You can select one or more channels.
When setting is completed, click “Confirm,” and press 【ENT】 to
When there is an alarm, the channels will be triggered to record (the
return to “Alarms” setup interface. The parameters can be copied to
record type of the channel is alarm), and the monitor will switch to
other alarm inputs.
preview the channels (On Screen Warning is enabled).
Press “Confirm” in the “Alarms” setup interface to save the
Set alarm input precaution time: Upon alarm, preview image
parameters. You can press “Cancel” or 【ESC】 key to cancel the
switches to the corresponding camera to trigger alarm outputs
parameters.
during the armed period. Select date first, then set time segment.
Note:
Time segment is set according sequentially, segment cannot overlap,
(1) You should connect dome cameras supporting preset, cruise
and no nesting is allowed. After the precaution time of a day is set,
function. The preset, cruise can be called up after you set a preset.、
the parameters already set can be copied to other dates.
cruise. Refer to part of “4.17 PTZ” for preset position and cruise
Note: Arm time periods should be set in chronological order, no
setting.
overlapping or nesting is allowed. All day arm setting time is: 00:
(2) The “sequence” function is unavailable at present.
00~24:00.
(3) One alarm input can trigger preset, cruise of multiple channels.
Handle Method: You can select one or more handle methods.
Note:
5. Alarm output handling mode
(1) Audible Warning: Requires external audio devices.
You can define the delay time and effective time of every alarm
(2) Upload To Center: To upload alarm signal to remote
output. Only during the effective time will the alarm output be
management center, “Remote Host IP address” and “port” of
triggered.
the client in the “Network” interface must be set; or to upload
In “Alarms” setup interface, select an alarm output, then select
alarm signal to the client PC, the DVR client software in the
delay time. The options are : 5s, 10s, 30s, 1m, 2m, 5m, 10m. The
PC must be armed.
actual alarm output time = alarm input remaining time + alarm
(3) To trigger one or multiple alarm outputs, select the
output delay time. You can press “Stop Alarm” button in “Utilities”
corresponding alarm outputs.
interface to clear the alarm output.
After completing setup, press “Confirm” to return to previous
In “Alarms” setup interface, click on “Schedule” button on the right
interface. In the “Alarms” setup interface, you can copy the
side of the “AlarmOut Time” and press 【ENT】 to enter into
parameters to other alarm inputs. Press “Confirm” in the “Alarms”
“AlarmOut” setup interface:
setup interface to save the parameters. You can press “Cancel” or
【ESC】 key to cancel the parameters.
37
2. Network Parameter Setting
Move the cursor to the corresponding editing box using 【→】 or
【→】key, press 【IRIS+】 to enter the editing mode. Press numeric
keys to input the corresponding numbers, press 【IRIS+】 key to
delete the numbers before the cursor. Press “Confirm” to save and
exit editing, and press 【ESC】 key to exit editing without saving.
NIC type
Network Card Type, default is 10M/100M auto, options are 10M
half-duplex, 10M full-duplex, 100M half-duplex, 100M full-duplex etc.
MAC:
Network Physical Address, only for display, not for editing. The
MAC of the device cannot be revised.
IP address
This IP address must be unique, and cannot conflict with any host or
working station in the same network segment.
Port Number
Figure 4-44
Port Number must be in the range of 2000 ~ 65535.
Mask IP address
Select date first, then set time segment. Time segment is set
Used to mark off the sub-net segment. Enter the IP mask of the DVR.
sequentially. Segments cannot overlap and no nesting is allowed.
Gateway address
After the precaution time of a day is set, the parameters already set
You need to set the gateway address to enable communication
can be copied to other dates.
between the different network segments.
When setting is completed, click “Confirm,” press【ENT】 to return
DNS address
to “Alarms” setup interface. The parameters can be copied to other
Focus on “DNS” and enter the DNS address, press Confirm when
alarm outputs.
done.
Press “Confirm” in the “Alarms” setup interface to save the
Multi cast address
parameters. You can press “Cancel” or 【ESC】 key to cancel the
Class-D network IP address, range is between 224.0.0.0 and
parameters.
239.255.255.255. If the network protocol does not adopt the multi
cast, it need not be set.7
4.16 Network Parameter Remote Host IP and its port
If setting the management IP address and its port, when there is
Enter “Network” menu interface to perform network-related
alarm event or exceptions event, the remote alarm host (install the
parameters setting. Note that the parameters become effective only
client software) will receive and record these events.
after the DVR is rebooted.
Network storage parameter
Network storage parameter includes IP address and the shared
1. Entering Menu Operation
directory name of network storage server.
Press 【MENU】 key to enter “Menu Operation” interface under the
NAS IP: Input the IP address of network storage server
PREVIEW mode, move the cursor to “Network” using 【←】 or
Directory name: Input the shared directory name of network
【→】 key, and press 【ENT】 key on the front panel to enter
storage server.
“Network” menu interface.
Http Port
The port of IE browser, default is 80. Visit method: Open and run the
IE browser on PC, and input the IP address of DVR that want to visit.
Note: You need to set the ActiveX control of IE to enable download
first, and then you can download DVR Control. Please refer to Help
document of IE for detail.
Set PPPoE
If you want to boot PPPoE dial-up mode, mark it as “√”, and input
the user’s name ( this user’s name can be obtained from the Internet
Server Provider), PPPoE dial-up password, input again the
password in “verification” so that the system will check the
password entered.
After finished, select “Confirm” key to save the parameters set.
Select “Cancel” key to cancel the setup and return to the main menu.
Refer to “5.1 PPPoE dial-up” for details.
Figure 4-45
38
Note:. PREVIEW mode, move the cursor to “PTZ” using 【←】or【→】 key,
(1) The options of “NIC type,” “IP address,” “Port Number,” and and press 【ENT】 key on the front panel to enter “PTZ” menu
“Mask IP address” are necessary options unless dynamic IP interface.
address is accessed.
(2) To make the parameters effective, you must reboot the DVR.
E-mail Setting
Move the cursor to “Setup” on the right side of “E-mail” and press
【ENT】 key on the front panel to enter “Email Setting” interface
shown as below:
Figure 4-47
2. Basic setup
Select camera protocol, Baud Rate, Data Bits, Stop Bits and Parity.
All parameters must be consistent with the protocol and the actual
setup of the PTZ.
Select protocol and input the PTZ address. At present the supported
protocols are Infinova, Pelco-P, Pelco-D, EVI-D30, Samsung, Vcom
VC-2000, Panasonic, Kalatel-312. In future software upgrades there
will be more protocols supported. Please refer to the software.
Figure 4-46
Preset position, sequence and cruise are set according to
requirements. The setup methods of preset positions and cruise are
Authentication: Click “√” if authentication is needed and input
described as follows. The setup and deletion methods of sequence
the information of User and Password. (User is the same as Sender
and cruise are similar.
Name).
Sender Name: Seen by the receiver and it can be set up
3. Set PTZ Preset
accordingly.
Move the cursor to “Preset Setup” in the “Preset” using 【←】 or
Sender Address: Mailbox address of sender.
【→】key, and press “Confirm” to enter “Set Preset” interface.
Email Server: IP address of the sender email server.
Mail Receiver NO.: 1 and 2 are optional.
Name: Receiver name.
Address: Receiver address.
Attachment JPEG: JPEG capture of trigger alarm.
JPEG Capture Interval: 2s, 3s, 4s, 5s are optional.
After the completion for Email Setting, user can enable “Send
Email” in Alarm handle interface.when exceptions (Hard Disk full,
Hard Disk error, network cable break, IP address conflict, illegal
access, unconformity of input & output format, abnormal video
signal, view tampering, video loss, motion detection, signals etc.)
happen, system will send alarm information to designated mailbox
(refer to section 4.10, 4.11, 4.12, 4.15, 4.19 for detailed alarm
Figure 4-48
handle method setting) .
Input a preset number in preset edit frame. The range is from 1 to
4.17 PTZ 128 (Note: The number of the presets is vary with the protocol used
by PTZ). Then enter into the “Adjust” interface to operate the PTZ
“PTZ”function can be used to initialize the setup of PTZ domes in the
to the desired position through the direction keys, and adjust the
system, and set up preset. Presets can be called up under control of PTZ.
lens through keys 【WIDE】, 【TELE】, 【*】, 【田】, 【IRIS
Please refer to “3.4 PTZ Control”on how to call out presets.
+】 and 【IRIS-】. 【TELE】 and 【WIDE】 mean zoom in and
zoom out respectively. 【*】 and 【田】 means FOCUS increase
1. Menu Setup
and reduce respectively. 【IRIS+】 and 【IRIS-】 mean IRIS
Press 【MENU】 key to enter “Menu Operation” interface under the
39
increase and reduce respectively. Select “Save” after completing the under other protocols. And in PTZ Linkage interface, there is no
adjustment. The preset position is saved. If you want to define other other options but the first Cruise selected.
preset positions, repeat the above procedures. Under Peleco P and Infinova protocol, control address is 1 didit less
After finishing the setup, execute “Return.” Execute “Confirm” in than the dome address.
“PTZ” interface, and the parameters set will become effective.
Note: When using SAMSUNG protocol, the preset number by 4.18 RS232 Setup
called should be 1 lower than the input preset number set before (e.g.
When calling up preset, input the preset number 2, in fact, it will This section covers setup of the parameters for communication
call up the preset number 1). For more information about protocol, between devices connected through serial ports and DVRs.
please contact Infinova service personnel.
4. Delete PTZ Preset 1. Enter setup menu
Enter into “Set Preset” interface of “Preset”. Input a preset number Press 【MENU】 key to enter “Menu Operation” interface under the
to be deleted in the preset editing frame. The range is from 1 to 16. PREVIEW mode. Move the cursor to “RS232” using 【←】 or
Press “Delete” key. If you want to delete more preset positions, 【→】 key, and press 【ENT】 key on the front panel to enter
repeat the above procedures. “RS232” menu interface.
After finishing the deletion, press “return.” Press “Confirm” in
“PTZ” interface. The delete operation becomes effective.
Note: This function is not currently available.
5. Set Sequence
This function is unavailable at present.
6. Set Cruise
Press “Setup” button on the right side of “Cruise” item, to enter the
“Set Cruise” interface:
Figure 4-50
2. Setup
Select “Baud Rate”, Data Bits, Stop Bits, Parity, and flow Ctrl. All
parameters must be consistent with the device linked.
“Mode”means serial port type. Options are console, PPP, Direct,
and transparent channel.
(1) For “PPP” or “Direct”: you need to set PPP mode
(active/passive), dial back mode (assigned by dialer/preset dial
back number.), respectively, then to input the parameters such
Figure 4-49 as remote IP address, local IP address, mask, user’s name,
password and verification, and telephone number. Confirm
whether dial back is needed and whether the transferred data
Click the“RecCru” button to enter the “PTZ control” interface, then need be encrypted or not. Please refer to “5.2 PPP (Modem)
you can control the PTZ via the direction keys, finally click passive dial-up” for details on use and operation of “PPP”, and
【ENTER】to save the PTZ action track and return to“Set Cruise” “5.3 Serial port Directly Connected”for details on use and
interface. operation of “serial port direct connection.”
Click the“StartCru” button to execute the recorded PTZ action track (2) For “transparent channel”: please pay attention to the
until you click the“Stop” button. connection method between DVR and matrix switcher. The
Click the “Return” button to get back to the “PTZ” interface. In series port pin definition of matrix switcher is as follows:
“PTZ” menu, press “Confirm” button to save this cruise. press
“ESC” to exit.
Note: Not all the PTZ support this cruise function. Contact with
your supplier when you can’t execute the function.
There are four Cruises are available under Pelco D, but only one The connection between DVR and matrix switcher is as follows:
40
DVR(RJ45) Matrix switcher(series port) description indicates how to set up relevant parameters for different
RxD 2 ←―――――― 5 TxD links to an ATM machine.
TxD 3 ――――――→ 4 RxD The system needs a second development. The bottom program
GND 7 ――――――― 7 GND should be customized according to the specific project. The current
version only supports the Demo program.
After completing the setup, select “Confirm” key to save the Enter menu setup
parameters. The parameters will become effective after rebooting Press 【MENU】 key to enter “Menu Operation” interface under the
the DVR. Select “Cancel” or press 【ESC】 key to cancel the setup “PREVIEW” mode, move the cursor to “Transact” using 【←】 or
and return to the main menu. 【→】key, and press【ENT】key on the front panel to enter
Note: “Transact” menu interface.
Press【00】numeric key to turn the page of characters.
4.19 Exceptions
This defines how exceptions occurring in the DVR are to be
handled. The exceptions include Hard Disk full, Hard Disk error,
illegal access, IP address conflict (Unavailable currently), network
failure, NTSC/PAL differ etc.
1. Operation
Choose appropriate input method (“Get Through”).
Input required:
IP address of ATM/POS
Figure 4-51 Type of ATM/POS
Start & end position, length and the content of data file
Start & end position and length of card no. length
2. Operation Start & end position and length of card number
(1) Select the type of the exceptions using 【↑】 or 【↓】 key. Start & end position and length of transaction type
(2) Select or cancel the handling method for this Exception via Transaction type and code
【ENT】or【IRIS+】key.
(3) Repeat step (1) and step (2) to select the type of exception and
corresponding handling method.
(4) Press “Confirm” to save the parameters after the entry is
finished. Select “Cancel” or press 【ESC】 key to exit without
saving, and return to the main menu interface.
41
Figure 4-53 Figure 4-55
(2) Network receiving (4) Receive the command sent by ATM/POS through serial ports.
Passively receive the information from ATM through the Receive the data from ATM passively through serial ports. The
network. ATM sends command to DVR when the transaction ATM needs to intergrate the communication protocol of the
happens, command DVR to fold characters and trigger record, DVR network data.
etc. However, DVR does not receive any information which Input required:
send by ATM to the bank server. ATM system needs to The type of ATM/POS machine
intergrate the communication protocol of the network data. Transaction type and code
Input required:
IP address of ATM/POS
The type of ATM/POS
Transaction type and code
Figure 4-56
4.21 Utilities
Press 【MENU】 key to enter “Menu Operation” interface under the
Figure 4-54 PREVIEW mode. Move the cursor to “Utilities” using 【←】 or
【→】 key, and press 【ENT】 key on the front panel to enter
(3) Receive data sent by ATM/POS through serial ports “Utilities” menu interface.
Receive the data from ATM actively through serial ports. The
bank should provide the data format and data bit, etc.
Input required:
The type of ATM/POS
Transaction type and code
42
Figure 4-60
Figure 4-57
Figure 4-61
Input the host IP address that has configured FTP server program,
and select “Confirm”. The system begins to upgrade. The system
will display a message regarding the upgrading progress.
Figure 4-58
Figure 4-62
Hint: If user wants to upgrade the DVR’s firmware from FTP, first
need configure FTP server program for the system. The following
steps are an example for configure the FTP server program:
(2) Setup the FTP server program on the client PC (here take
Figure 4-59 "WFTPD32.EXE" as an example)
1) Add user
Note: After resetting to factory default, all parameters of the DVR Operate WFTPD32 FTP server program. In the main
will reset to factory default parameters, all user data will be lost and window of WFTPD32, select “Users/rights” under
all parameters must be reset. Extreme caution should be exercised in “Security” menu to enter “Users/rights Security” dialog
using this function. box:
3. Upgrade
This menu will upgrade the DVR’s firmware from the host or USB
interface device.
Figure 4-63
43
Click “New user” button in the above dialog box, and input the user Hard Disk Selection
name and password in the popup dialog box (the defaults of user Select the Hard disk to be viewed or managed using 【↑】 or 【↓】
name and password both are “target”), thus add a new user “target”. key. One DVR can utilize up to eight internal SATA hard disks.
Note: The defaults of user name and password both are “target”, Check the assigned hard disk current status
which are built into the DVR program, and cannot be changed when Currently, hard disk current status is provided only for the
upgrade the DVR’s firmware from FTP. So user must configure the designated hard disk.
default user for the FTP server. Format the assigned hard disk
2) Setup the upgrade file path Before formatting, please stop all recording and other functions.
In the “Users/rights Security” dialog box as show in figure After formatting, you must reboot the DVR or it will not function
4-59, select the user “target” in the “User name” list frame, properly.
and input the path where the upgrade file "digicap.hex"
locates to "Home Directory" text box, then click “Done” 2. Clear alarm out
button. Thus the setup is finished. Clear alarm output.
3) After finish the configuration of FTP server program for
the system, user can upgrade the DVR’s firmware from
3. Reboot
FTP via network.
Reboot the DVR.
(3) Upgrade from USB
If user wants to upgrade the DVR’s firmware from USB interface
4. Shut down
device, fist need save the upgrade file "digicap.hex" in the USB
Shut down DVR.
device, and then connect the USB device to the USB interface of
DVR.
Select “USB” upgrade mode in the upgrade dialog box as shown in 5. View Log
figure 4-60, the system begins to upgrade from the connected USB Search the log. Enter into “View Log” menu interface. To search
device. The system will display a message regarding the upgrading according to the defaulted condition, press 【Enter】 key in front
progress, as shown in Figure 4-62. panel. All log information in the DVR will be listed in log dialog.
To search by condition, please refer to the following operations
(4) Upgrade from CD (according to type, time, type & time modes respectively).
If user wants to upgrade the DVR’s firmware from CD interface
device, fist need save the upgrade file "digicap.hex" in the CD
device, and then place the CD device in the CD-ROM of DVR.
Select “CD” upgrade mode in the upgrade dialog box as shown in
figure 4-60, the system begins to upgrade from the connected USB
device. The system will display a message regarding the upgrading
progress, as shown in Figure 4-62.
Reboot after successfully upgrading. The system will use the new
firmware. For detailed information about upgrading, Please contact
Infinova customer service.
Figure 4-65
44
voice dialogue, remote upgrading, remote file playback, remote 6. Check system information
playback according to time and remote PTZ control. Displays system information such as device name, model number,
Alarm Log includes alarm input, alarm output, start motion detection, serial number, version, receiver version, encoding version, etc. All
end motion detection, view tamper start and view tamper stop. information is for display only, not for revising.
Exception event Log including signal lost, illegal access, hard disk
error, hard disk full, IP conflict and DCD lost.
45
Chapter V Network Operation 2. Access through domain name server
The adoption of this mode requires a PC that has a fixed IP address
5.1 PPPoE Dial-up located on Internet, and the domain name server software must be
running on this PC (We call this PC the DNS server).
Before using this function, please make sure DVR has PPPoE
dial-up function.
PPPoE dial-up is mainly used to connect DVR to Internet through
UTP port.
Figure 5-2
Operation:
(1) Press 【MENU】 key to enter “Menu Operation” interface
under the PREVIEW mode. Move the cursor to “Network
Setting” using 【←】 or 【→】 key, and press 【ENT】 key
on the front panel to enter “Network” menu interface.
(2) Move the cursor to “User” using 【←】 or 【→】 key, press
【IRIS+】key to edit. Press【numeric】keys to enter numbers,
Figure 5-1 English characters (Upper case, Lower case) and symbols,
press 【*】 to switch among numbers, English characters
(1) Move the cursor to “PPPoE” using 【←】 or 【→】 key, press (Upper case, Lower case) and symbols, press【0】numeric key
【IRIS+】or “Confirm” to select “PPPoE”, and mark it as “√.” to turn the page of characters, press 【IRIS+】 key to delete the
characters before the cursor. Press 【ENT】 key to temporarily
(2) Move the cursor to “Username” using 【←】 or 【→】 key, save and exit the editing mode. Press【ESC】key to cancel the
press 【IRIS+】 key to edit. Press【numeric】 keys to enter entry and exit the editing mode. Enter “PPPoE username”
numbers, English characters (Upper case, Lower case) and provided by ISP.
symbols, press 【*】 to switch among numbers, English (3) Repeat Step (2) to enter “Pass” and “Veri”.
characters (Upper case, Lower case) and symbols, press【0】 (4) Repeat Step (2) to enter the IP address of receiver in the “DNS
numeric key to turn the page of characters, press 【IRIS+】 key address”.
to delete the characters before the cursor. Press 【ENT】 key to (5) Press “Confirm” to save the change above and restart the DVR.
temporarily save and exit the editing mode. Press 【ESC】 key (6) Enter the DVR name in “Surveillance Server Name” in the
to cancel the entry and exit the editing mode. Enter “PPPoE “Local Setting”, start the receiver and enter the IP address of
username” provided by ISP. receiver, and enter the surveillance camera, username,
password etc.
(3) Repeat Step (2) to enter “pass” and “Veri”. Save after the entry after finishing, and DVR can be accessed.
(4) Press “Confirm” to save the change above and restart the DVR. Working theory: DVR adopts PPPoE mode to establish the
network connection. It will modify IP address in “network” to be IP
The restarted DVR will create the network connection by PPPoE. address of the Internet, and will send the name and the current IP
After the connection is successful, change the IP address in the address to the domain name server. When the client PC user wants
“Network” to the obtained Internet dynamic IP address. to access DVR through client software, the client PC should connect
with the PC that is set as domain name server, telling the domain
5.1.2 Access through Client Software when Using PPPoE name server the name or the serial number of DVR to be accessed.
The domain name server will search all the DVRs registered to find
1. Access directly through IP address of current device.
the matched DVR and the corresponding Internet IP address, and
After successful PPPoE dial-up, view “IP” in “Network.” Acquire
communicate this address to client software. The client PC user can
the device current IP address. Then the client PC will access the
access the DVR with the current IP address..
DVR using this IP address.
46
5.2 PPP(Modem) Passive Dial-up PREVIEW mode, move the cursor to “Record” using 【←】 or
【→】 key, and press 【ENT】 key on the front panel to enter
Before using this function, please make sure that the DVR used “Recording Channel Configuration” menu interface.
supports PPP passive dial-up function.
The setting is as follows:
PPP passive dial-up is used to connect a PC to the DVR via public
Code stream type: Audio & Video
telephone line. Dial-up is performed before a PC accesses the DVR.
Resolution: DCIF
The PC can monitor and control the DVR via client-end software
Bit rate type: variable
after dial-up is successful.
Max bit rate: 512Kbps
Two Modems are required to perform PPP passive dial-up, one used
Image quality: high
for connection with RS232 interface of the device through a DB9 to
RJ45 cable, another used for connection with the COM port of the Frame rate: 30(N)/25(P)
PC through a DB9 to RJ45 cable. The two modems are connected to The video frame rate is confirmed according to resolution. If you
the public telephone line network. choose CIF as the resolution, it is recommended to select frame rate
as 1 frame. When choosing resolution as QCIF, it is recommend to
5.2.1 DVR Terminal Setup select frame as 4 frame. Resolution CIF has a better definition,
while QCIF resolution has a shorter delay. User can adjust the Bit
DVR terminal setup includes “RS232” and “video signal parameter Rate, resolution and video frame rate according to the actual
setup.” application.
1. Setup the RS232 port of DVR The set effect is as follows:
The parameter value of Baud Rate, Data Bits, Stop Bits, Parity,
Flow Ctrl, must be consistent with the Modem defaulted parameter
value connected with PC.
Press 【MENU】 key to enter “Menu Operation” interface under the
PREVIEW mode. Move the cursor to “RS232” using 【←】 or
【→】key, and press 【ENT】 key on the front panel to enter
“RS232” menu interface.
The result is as follows after setup:
Mode: PPP
PPP mode: passive
Callback: by dialer
Remote IP: After successful PPP dial-up, it will assign the
designated IP address to PC, e.g. set as 192.1.0.1;
Local IP: After successful PPP dial-up, it will assign the designated
IP address to the video recorder, e.g. set as 192.1.0.2
Mask: 255.255.255.0 Figure 5-4
The following shows setup of a modem:
Move the cursor to “Confirm” after the setting is finished, and press
“Confirm” to save and exit the “Recording channel configuration”
menu interface.
47
5. Cut off the modem that has been set from a PC, and Connect
modem with the RS-232 serial port of DVR through a DB9 to
RJ45 cable.
Figure 5-5
Figure 5-7
48
6. You can preview the image of 192.1.0.2 via Infinova client “New Connection…,” select “Connect directly to another
software, after the successful dial-up. computer” according to the guide, press next, select “Guest” in
“Host or Guest”, press next, and select the device as
5.3 Serial Port Directly Connected “Communications cable between two computers” to complete the
establishment of direct connection according to the guide.
Before using this function, please make sure that all DVRs have the
serial port direct connect function. 2. Configure “Direct Connection”
The serial port is used to connect the DVR’s RS232 port with PC Open “Network and Dial-up Connections” in the control panel,
COM port through a DB9 to RJ45 cable. The PC can directly access open the “Direct Connection,” select “General,” press “Configure”
the DVR through the COM port and a DB9 to RJ45 cable connected in “General.”
to it.
Figure 5-8
49
Appendix I Specifications
50
Appendix II Typical Connection
51
Appendix III Frequently Asked Questions
Note:
(1) Place the DVR in a well ventilated place.
(2) The DVR must operate in the allowed range of temperature and humidity detailed in specification.
(3) When exposed to water, dust on circuit board can cause short circuit. The circuit board, plug and socket, housing fan and housing must
have dust removed by brushing regularly to maintain long range normal operation of the DVR.
(4) The software of DVR is stored in FLASH memory. Under two following conditions: a) software-updating to replace the original
software inside the DVR with new software, and b) the code in FLASH is damaged to some degree, and the same version software is
re-written into FLASH, software upgrading is required. Please contact Infinova customer service for details.
52
Appendix IV V3013 Product Storage Calculator
Bit Rate 1 channel 2 channel 4 channel 6 channel 8 channel 10 channel 12 channel 16 channel
32K 9709 days 4854 days 2427 days 1618 days 1213 days 970 days 809 days 606 days
48K 6472 days 3236 days 1618 days 1078 days 809 days 647 days 539 days 404 days
64K 4854 days 2427 days 1213 days 809 days 606 days 485 days 404 days 303 days
80K 3883 days 1941 days 970 days 647 days 485 days 388 days 323 days 242 days
96K 3236 days 1618 days 809 days 539 days 404 days 323 days 269 days 202 days
128K 2427 days 1213 days 606 days 404 days 303 days 242 days 202 days 151 days
160K 1941 days 970 days 485 days 323 days 242 days 194 days 161 days 121 days
192K 1618 days 809 days 404 days 269 days 202 days 161 days 134 days 101 days
224K 1387 days 693 days 346 days 231 days 173 days 138 days 115 days 86 days
256K 1212 days 606 days 303 days 202 days 151 days 121 days 101 days 75 days
320K 969 days 484 days 242 days 161 days 121 days 96 days 80 days 60 days
384K 808 days 404 days 202 days 134 days 101 days 80 days 67 days 50 days
448K 693 days 346 days 173 days 115 days 86 days 69 days 57 days 43 days
512K 606 days 303 days 151 days 101 days 75 days 60 days 50 days 37 days
640K 485 days 242 days 121 days 80 days 60 days 48 days 40 days 30 days
768K 404 days 202 days 101 days 67 days 50 days 40 days 33 days 25 days
896K 346 days 173 days 86 days 57 days 43 days 34 days 28 days 21 days
1M 303 days 151 days 75 days 50 days 37 days 30 days 25 days 18 days
1.25M 242 days 121 days 60 days 40 days 30 days 24 days 20 days 15 days
1.5M 202 days 101 days 50 days 44 days 25 days 20 days 16 days 12 days
1.75M 173 days 86 days 43 days 28 days 21 days 17 days 14 days 10 days
2M 151 days 75 days 37 days 25 days 18 days 15 days 12 days 9 days
53
Appendix V USB Mouse Control Left click mouse:To Select the file to copy or cancel copy.
Double Left click mouse:To Play recording file
Right click mouse:To Return to preview interface.
1 Preview
Description in play interface:
Left click mouse :To select multiple screen preview Double Left click mouse:To Pause or resume.
Right click mouse:To flip screen display manually Right click mouse:To Quit and return to playback interface.
Double left click mouse:To Enter Main Menu Move the middle key of mouse upward:To Change play rate
Note:As for how to type the password in the Dialogue box of“Log backward.
In”,please refer to Section 3.3 Username and password. Move the middle key of mouse downward:To Change play rate
Regarding the operation instruction of menu interface, please refer forward
to 5 Menu Interface
Double right click mouse:To display the selected channel in full 5 Menu interface
screen under multiple screen display mode;; double click to resume
multiple display preview. Left click mouse: To Enter the lower lever menu.
Middle click mouse:To enter PTZ To Perform each button in the menu.
To Enter character editing mode. ( As for the
Note:As for how to type the password in the Dialogue box of editing method please refer to “the Middle
“Log In”,please refer to Section 3.3 Username and password. click mouse” of 5 Menu Interface)
In regard tohow to do PTZ operation, please refer to Section 3.4
PTZ control IRIS+ IRIS-
Move the middle key of mouse upward::To enter play back
FOCUS+ FOCUS-
interface.
OPTIC ZOOM+ OPTIC ZOOM-
Note: For how to input the password in Dialogue box“Log
UP
In”,please refer to Section 3.3 Username and password.
Please refer to Section 3.6 Playback to see how to playback LEFT RIGHT
Move the middle key of mouse downward: To enter manual
AUTOMATIC
recording interface DOWN
54
Move the middle key of mouse upward:To eliminate the area that Left click mouse:To cancel the setup and return to the superior
has been set the area setup. menu.
Move the middle key of mouse downward:To set the detection area Middle click mouse: To save the setup and back to the superior
as full screen. menu.
Move the middle key of mouse upward:To clear the area set.
7 Privacy Mask Area Setup Interface
Hold the left key of mouse to drag; To mark out an area.
55
Infinova
51 Stouts Lane,
Monmouth Junction, NJ 08852, U.S.A.
Tel: 1-888-685-2002 (USA only)
1-732-355-9100
Fax: 1-732-355-9101
sales@infinova.com
V2.5 1008