Académique Documents
Professionnel Documents
Culture Documents
MDE-LEDI-NETWORK-IN-4065V1.0
Consignes de sécurité importantes
L’installation électrique sur laquelle le matériel est raccordé doit être réalisée
conformément à la norme NF C 15-100 .
Les produits GORGY TIMING sont conformes aux normes : CE, EN 60950, EN 55022,
EN 50024.
2 MDE-LEDI-NETWORK-IN-4065V1.0
SOMMAIRE
1. inTRODUCtion............................................................................................................. 5
1.1.Installation rapide................................................................................................................... 5
1.1.1. Vérifiez le contenu du carton..................................................................................... 5
1.1.2. Connectez le produit.................................................................................................. 6
FRANCAIS
1.2. Configurez votre produit........................................................................................................ 6
2.1.1. Configuration réseau manuelle.................................................................................. 6
2.1.2. Configuration des cartes de sortie............................................................................. 7
1.3. Généralités............................................................................................................................ 7
1.3.1. Principes de la synchronisation................................................................................. 7
A/ Principes de la correction d’horloge.......................................................................... 7
B/ Dialogue réseau........................................................................................................ 9
C/ Travailler avec plusieurs serveurs............................................................................. 9
1.3.2. Le logiciel client NTP............................................................................................... 10
2. Configuration complète....................................................................................11
2.1. Configuration réseau............................................................................................................11
2.1.1. Configuration par défaut...........................................................................................11
2.1.2. Changement des paramètres réseau.......................................................................11
2.1.3. Intégration dans votre réseau.................................................................................. 13
2.2. Configuration des cartes de sortie....................................................................................... 14
2.2.1. Introduction.............................................................................................................. 14
2.2.2. Configuration par défaut.......................................................................................... 14
2.2.3. Changer les réglages.............................................................................................. 14
2.2.4. Paramètres génériques........................................................................................... 15
A/ Fuseau horaire........................................................................................................ 15
B/ Politique de changement d’heure (DST : Day Saving Time)................................... 15
C/ Désactivation des sorties........................................................................................ 15
4. Interface WEB......................................................................................................... 19
4.1. Présentation........................................................................................................................ 19
4.2. Description de l’interface WEB............................................................................................ 20
4.2.1. Ecran Principal........................................................................................................ 20
4.2.2. Réglages standards................................................................................................. 21
4.2.3. Configuration SNMP ............................................................................................... 24
4.2.4. Configuration NTP .................................................................................................. 26
4.2.5. Configuration des sorties......................................................................................... 28
MDE-LEDI-NETWORK-IN-4065V1.0 3
6 Annexe A – Connexions............................................................................................ 35
1. Connexion pour tous les produits........................................................................................... 35
1.1. Produits 230V et 115V AC (type ‘0’)........................................................................... 35
1.2. 18/72V DC product (type ‘9’)...................................................................................... 35
2. Sortie pour carte type ‘B’ (sortie double AFNOR/IRIG-B NFS87500)..................................... 36
3. Sortie pour carte type ‘A’ (ASCII+TOP).................................................................................. 37
Annexe C – Caractéristiques............................................................................... 42
1. Dimensions............................................................................................................................. 42
2. Spécifications électriques....................................................................................................... 42
3. Autres spécifications............................................................................................................... 42
4 MDE-LEDI-NETWORK-IN-4065V1.0
1. inTRODUCtion
Ce document est le manuel d’utilisation pour le LEDI Network IN. Ce produit est un client
NTP. L’objectif de cet appareil est de synchroniser divers équipements en utilisant le temps
FRANCAIS
de référence fournit par un ou plusieurs serveurs NTP. Ce produit peut être vu comme une
sorte de convertisseur qui traduit un « signal NTP » en signaux de synchronisation tradi-
tionnels (ASCII+TOP, AFNOR, IRIG-B par exemple).
En utilisant le LEDI Network IN avec un serveur Gorgy Timing, vous facilitez fortement
l’installation et l’utilisation.
Cette partie contient les informations élémentaires pour l’installation du LEDI Network IN.
Vous trouverez des informations complémentaires dans la partie 3.
►► Un câble réseau.
MDE-LEDI-NETWORK-IN-4065V1.0 5
1.1.2. Connectez le produit
►► Il est fortement conseillé de noter le numéro de série (inscrit sur l’étiquette d’identifi-
cation), la localisation et un bref descriptif du produit. Vous pouvez utiliser pour cela
la fiche dans Annexe E – Documents complémentaires.
►► Connectez les sorties de synchronisation à vos équipements (voir Annexe A –
Connexions pour plus d’informations).
Cependant, Gorgy Timing vous recommande d’inscrire pour chaque produit son empla-
cement physique. Ceci est possible grâce au logiciel GTNetMng fournit sur le CDROM.
Pour plus d’informations, voir la partie 31.2.
Les produits NTP Gorgy Timing sont configurés en usine pour récupérer automatiquement
une adresse IP. Deux mécanismes sont utilisés :
1. Si un serveur DHCP est présent sur votre réseau, le produit récupère une adresse
automatiquement. Ceci assure la compatibilité de l’adresse IP avec votre réseau.
1/ Il se peut par exemple que vous n’ayez pas la possiblité de configurer le LEDI Network IN par un navigateur WEB.
6 MDE-LEDI-NETWORK-IN-4065V1.0
1. inTRODUCtion
L’identificateur DHCP par défaut est CRnnnnnn (nnnnnn est le numéro de série du
produit).2 Vou pouvez changer cet identificateur grâce au logiciel GtNetMng, ou à tra-
FRANCAIS
vers l’interface WEB, comme décrit dans les parties 31.2 et 52.2.
Si vous n’avez pas de serveur DHCP ou que vous souhaitez configurer vous-même les
paramètres réseau, utilisez l’outil GTNetMng sur le CDROM pour changer les paramè-
tres réseau. Veuillez vous référer à la partie 31.2 pour plus d’informations.
Par défaut, toutes les cartes de sortie fournissent l’heure UTC. L’heure reçue du ser-
veur NTP est directement envoyée en sortie.
Chaque carte peut-être configurée pour fournir plusieurs heures locales. Cette configu-
ration est effectuée au travers d’un navigateur WEB (voir la partie 32).
1.3. Généralités
Cette partie décrit les concepts généraux du produit LEDI Network IN. Elle permet de com-
prendre le fonctionnement du produit dans différentes circonstances.
Le logiciel NTP client est le cœur du LEDI Network IN. Il effectue toute la synchronisation,
la gestion du matériel et fournit les informations pour l’interface WEB et pour le protoco-
le SNMP.
2/ Certains serveur DHCP peuvent enregistrer le nom DHCP dans le DNS. Dans ce cas, vous pouvez accéder au
LEDI Network IN directement par son nom DHCP au lieu de son adresse IP.
MDE-LEDI-NETWORK-IN-4065V1.0 7
Pour réaliser cette synchronisation, le logiciel client NTP compare en permanence les
deux horloges et calcule les informations suivantes :
►► Le décalage :
C’est la différence entre l’heure de l’horloge serveur, et celle de l’horloge cliente.
Par exemple, si l’horloge serveur indique2:10:13 et que l’horloge cliente indique
2:11:14, alors le décalage est –1 :01 .
►► La dérive :
C’est la différence de fréquence entre les deux horloges. Quand la dérive est non-
nulle et sans correction d’horloge, le décalage entre les horloges augmente ou di-
minue, en fonction du signe de la dérive.3
Le schéma suivant montre l’évolution des deux horloges avec et sans décalage :
Heure serveur
Dérive nulle
Heure serveur
Heure client
Heure client
Heure serveur
L’objectif de la synchronisation d’un client NTP sur un serveur NTP est de réduire autant
que possible le décalage et la dérive. La précision et la stabilité de l’horloge du client
sont étroitement liés à l’efficacité de ce time
server processus de réduction.
Drift is null :
server time
client time
client time
3/ La présence d’une dérive a plusieurs causes possibles. Généralement, elle est due à la différence de tempéra-
ture entre les deux horloges.
server time
server time
8 Drift is constant : MDE-LEDI-NETWORK-IN-4065V1.0
client time
client time
1. inTRODUCtion
B/ Dialogue réseau
Le décalage et la dérive réel de l’horloge du LEDI Network IN par rapport à celle du
FRANCAIS
serveur NTP sont estimés d’après un décalage mesuré. Ce décalage est calculé en
soustrayant la date de l’horloge client à celle de l’horloge serveur.
Reçoit la réponse
Sur un LAN, il suffit de quelques millisecondes entre la requête de la date par le client,
et le moment où il reçoit la réponse. Ce retard est dû au délai de transmission sur le
réseau. Il peut varier en fonction de la charge du réseau ou de la charge du serveur
NTP. Plus grave, le temps de transmission du client au serveur n’est généralement pas
le même que du serveur au client.
En réalité, sur une grande période de temps, la somme des différences entre les délais
de transmission client-serveur et serveur-client vaut zéro. L’algorithme du client NTP
inclue dans le LEDI Network IN est conçu pour compenser les délais de transmission
et pour moyenner les mesures.
MDE-LEDI-NETWORK-IN-4065V1.0 9
1. inTRODUCtion
Démarrage
Recherche les
serveurs .
Apprentissage
Auto-détection du milieu
Erreur
Apprentissage
du milieu
Apprentissage
Pas de réponse
Travail Commutation
Commutation OK
10 MDE-LEDI-NETWORK-IN-4065V1.0
2. Configuration complète
Cette partie contient les informations pour la configuration complète du produit. Elle
2
doit être utilisée pour la configuration fine du réseau, et pour l’activation des cartes
FRANCAIS
de sortie.
L’identificateur DHCP par défaut du produit est CRnnnnnn, avec nnnnnn le numéro de
série sur 6 chiffres. Le numéro de série est indiqué sur d’étiquette d’identification sur le
dessus ou sur le dessous du produit.
L’identificateur SNMP par défaut du produit (visible à partir d’un navigateur SNMP (voir
partie 6) ou d’un navigateur WEB) est LediNtpRacknnnnnn, avec nnnnnn le numéro
de série sur 6 chiffres.
Utiliser le logiciel GTNetMng fourni sur le CD-ROM pour configurer votre appareil:
MDE-LEDI-NETWORK-IN-4065V1.0 11
►► L’outil GTNetMng affiche automatiquement les produits Gorgy Timing installés sur
votre réseau. Chaque ligne contient des informations sur un produit connecté, com-
me montré ci-dessous:
Localisation du produit
12 MDE-LEDI-NETWORK-IN-4065V1.0
2. Configuration complète
FRANCAIS
Vous n’avez à changer aucun réglage réseau pour les cas suivants :
►► Vous n’avez pas de serveur DHCP mais vous n’avez pas besoin d’accéder à l’appa-
reil par son interface WEB ou SNMP. Dans ce cas, le mécanisme AutoIP affectera
automatiquement une adresse IP, mais cette adresse sera probablement incompa-
tible avec votre réseau.
Certains serveurs DHCP ont la capacité d’enregistrer l’appareil dans le DNS. Dans ce
cas, le nom enregistré est l’identificateur DHCP. Vous pouvez ensuite accéder à l’ap-
pareil au travers d’un navigateur WEB ou SNMP. Par exemple, si vous donnez comme
nom DHCP inrack3 à votre LEDI Network IN, il vous suffit de taper inrack3 dans le
champs d’adresse de votre navigateur WEB.
Si vous avez plusieurs produits connectés à votre installation, il est fortement recom-
mandé de suivre les étapes suivantes :
►► Lancez GtNetMng sur un PC connecté sur le même réseau que celui du produit.
Tous les produits GT devraient apparaître avec leurs numéros de série. Entrez le
numéro de série et la localisation en utilisant le document rempli à l’étape précé-
dente.
MDE-LEDI-NETWORK-IN-4065V1.0 13
2.2. Configuration des cartes de sortie
2.2.1. Introduction
Votre LEDI Network IN est fourni avec jusqu’à 4 cartes de sortie. Chaque carte de sortie
est étroitement synchronisée sur le code horaire NTP reçu du serveur NTP. Chaque
carte agit comme une sorte de traducteur qui reçoit l’heure du logiciel NTP et fournit un
code horaire spécifique.
Il existe 2 types de cartes:
►► ASCII+TOP (carte type ‘A’).
►► AFNOR (carte type ‘B’).
Vous pouvez librement utiliser et copier le tableau Configuration des appareils dans
l’Annexe E – Documents complémentaires.
Dans cet écran, vous pouvez régler chaque carte indépendamment (voir la partie 52.5).
Quand vous avez changé les réglages, cliquez sur le bouton .
La modification devrait apparaître immédiatement à la sortie ou à l’écran.
14 MDE-LEDI-NETWORK-IN-4065V1.0
2. Configuration complète
FRANCAIS
fuseau horaire et la politique de changement d’heure (DST) peuvent être réglées. A
l’exception de l’afficheur, toutes les cartes de sortie peuvent être désactivées.
A/ Fuseau horaire
Le fuseau horaire est un décalage de temps qui peut être ajouté ou retiré du temps
reçu grâce au protocole NTP (qui est en heure UTC) pour générer l’heure locale.
Par exemple, en France, l’heure locale est GMT + 1:00. Si vous souhaitez qu’une
carte génère l’heure locale, utilisez l’interface WEB et réglez le décalage à GMT
+1:00.
MDE-LEDI-NETWORK-IN-4065V1.0 15
3. Interface face avant
L’interface de l’écran en face avant peut afficher jusqu’à 16 caractères. Deux bou-
tons vous permettent soit d’afficher la configuration, soit d’effectuer un redémarra-
ge global. L’afficheur est utilisé par le LEDI Network IN pour montrer l’heure actuelle
et les différentes conditions d’alarmes.
►► Si aucun serveur n’est configuré par l’utilisateur, le LEDI Network IN essaie de dé-
tecter les serveurs GT, et affiche ce message:
16 MDE-LEDI-NETWORK-IN-4065V1.0
3. Interface face avant
FRANCAIS
►► S’il y a au moins un serveur GT ou que l’utilisateur a configuré manuellement les
serveurs, le LEDI Network IN entre dans son étape d’apprentissage et affiche le
texte suivant :
Quand aucune alarme n’est activée et que le LEDI Network IN est correctement synchro-
nisé sur un serveur, l’heure actuelle du serveur est affichée en permanence. L’écran affiche
alternativement l’heure et la date comme montré ci-dessous :
• Quand l’afficheur est configuré pour montrer l’heure UTC, les informations suivan-
tes sont affichées alternativement :
• Quand l’afficheur est configuré pour montrer l’heure locale, les informations sui-
vantes sont affichées alternativement :
MDE-LEDI-NETWORK-IN-4065V1.0 17
3. Interface face avant
►► Si aucun serveur NTP n’a été trouvé au bout d’un certain temps, le LEDI Network
IN désactive ses sorties et affiche le message clignotant suivant:
18 MDE-LEDI-NETWORK-IN-4065V1.0
4. Interface WEB
4.1. Présentation
FRANCAIS
Le LEDI Network IN peut être configuré et supervisé à travers une inerface WEB. Cette
interface vout permet de :
Chaque LEDI Network IN intègre son propre serveur WEB qui délivre une page WEB. Ce
site WEB est un applet JAVA . si besoin une JVM (Java Virtual Machine) vous est fournie
sur le CD-ROM, dans le répertoire Common\JAVA.
Pour accéder au site WEB, entrez l’adresse du LEDI Network IN dans le champs d’adres-
ses de votre navigateur WEB (comme ci-dessous), et appuyez sur Entrée. 6
3. vous n’avez pas de JVM (Java Virtual Machine) installée sur votre PC.
Dans les deux premiers cas, vérifiez l’adresse IP de votre LEDI Network IN et votre confi-
guration réseau. Dans le dernier cas, vous devez installer la JVM (voir Common\JAVA sur
le CDROM).
6: Si vous avez configuré votre LEDI Network IN en mode DHCP et que votre serveur enregistre automatiquement
l’identificateur DHCP dans le DNS, vous pouvez entrer le nom DHCP au lieu de l’adresse IP
7/ Vérifiez en particulier la configuration de votre navigateur WEB.
MDE-LEDI-NETWORK-IN-4065V1.0 19
4.2. Description de l’interface WEB
Voici l’écran qui doit apparaître lorsque vous accédez au sit WEB du LEDI Network IN.
Les quatre premiers boutons à gauche de l’écran permettent d’accéder aux panneaux
suivants:
20 MDE-LEDI-NETWORK-IN-4065V1.0
4. Interface WEB
FRANCAIS
Lorsque vous cliquez sur le bouton Standard, les paramètres réseau et les informa-
tions sur le produit sont affichés ainsi :
En haut, vous pouvez contrôler les paramètres réseau et le mot de passe WEB. En bas
se trouvent des informations sur le produit.
Paramètres réseau
►► IP mode
Indique si le LEDI Network IN fonctionne en adresse IP fixe (entrée dans le champs
IP address) ou avec le protocole DHCP (l’identificateur DHCP est entré dans le
champs DHCP identifier).
MDE-LEDI-NETWORK-IN-4065V1.0 21
►► IP address
Indique l’adresse IP affectée au réseau. Une adresse IP est composée de 4 numé-
ros séparés par un point. Chaque numéro s’étend de 0 à 255.
►► DHCP identifier
Identificateur utilisé quand le LEDI Network IN est configuré en mode DHCP. Il est
composé d’au maximum 8 lettres. Sa valeur par défaut est CRnnnnnn (où nnnnnn
est le numéro de série sur 6 chiffres).
►► Network submask
Indique la taille du réseau que vous utilisez. Par exemple, un masque se sous-
réseau de 255.255.255.0 indique que seul le dernier numéro de l’IP change (dans
l’exemple ci-dessus, l’adresse dans le réseau peut varier entre 192.168.10.1 à
192.168.10.254)8.
►► Gateway address
Si vous voulez que le LEDI Network IN communique avec d’autres appareils en de-
hors du réseau local, vous devez indiquer une passerelle (gateway) qui sera utilisée
pour sortir du réseau local.
►► Without gateway
Cochez cette case si vous n’avez pas de passerelle sur votre réseau ou que vous
ne souhaitez pas l’utiliser.
8/ Si vous configurez plusieurs appareils pour communiquer sur le même réseau, vous devez avoir le même
masque de sous-réseau.
22 MDE-LEDI-NETWORK-IN-4065V1.0
4. Interface WEB
FRANCAIS
►► Firmware Version/Release Date
Version du logiciel fonctionnant sur le LEDI Network IN et la date du dernier logi-
ciel produit (au format anglais yymmdd, par exemple 021010 pour le 10 Octobre
2002).
Si vous souhaitez protéger l’accès aux paramètres du LEDI Network IN, vous pouvez spé-
cifier un mot de passe. Vous devez pour cela entrer le même mot de passe dans les zones
Enter password et Confirm password.
Si vous ne voulez pas protéger les paramètres, cochez la case Without password.
Quand un mot de passe est activé, il sera demandé à la prochaine connexion. Dans ce
cas, l’écran principal a cette apparence
MDE-LEDI-NETWORK-IN-4065V1.0 23
4.2.3. Configuration SNMP
Quand vous cliquez sur le bouton SNMP, les paramètres SNMP sont affichés ainsi :
alarmes du LEDI Network IN.9 L’accès à ces informations (la MIB) peut être “protégé”
par un mot clé, le Community Name.
Les alarmes sont envoyées à un navigateur SNMP localisé sur un ordinateur identifié
par son adresse IP. Jusqu’à 5 adresses IP de “traps” (Trap address) peuvent-être spé-
cifiées, ce qui permet de gérer les alarmes sur 5 ordinateurs différents.
Par convenance, les alarmes peuvent être envoyées par le protocole SYSLOG qui est
implémenté le plus souvent sous UNIX®.
24 MDE-LEDI-NETWORK-IN-4065V1.0
4. Interface WEB
Description
FRANCAIS
Voici une description des champs de cet écran:
►► SYSLOG File Id
dentifie le fichier à utiliser sur l’ordinateur distant pour le protocole SYSLOG.
►► Community name
Un simple mot clé nécessaire dans un navigateur SNMP pour accéder aux informa-
tions SNMP. Un mot clé doit avoir 8 lettres au maximum.
►► System name
Un nom que vous pouvez donner au LEDI Network IN. Ce nom apparaît dans la
variable sysName de la branche système de la MIB. La valeur initiale est LediNt-
pRacknnnnnn (où nnnnnn est le numéro de série du produit).
►► System location
Une éventuelle description de la localisation physique du LEDI Network IN. Ce nom
apparaît dans la variable sysLocation de la branche système de la MIB. Il n’y a
pas de valeur par défaut.
►► System contact
Personne à contacter en cas de problème avec le LEDI Network IN. Cette informa-
tion apparaît dans la variable sysContact de la branche système de la MIB. Il n’y a
pas de valeur par défaut.
MDE-LEDI-NETWORK-IN-4065V1.0 25
4.2.4. Configuration NTP
Le LEDI Network IN peut être synchronisé sur trois serveurs NTP au plus. En réalité,
le logiciel client NTP n’utilise qu’un seul serveur à la fois, mais peut commuter sur un
autre serveur s’il n’y a pas ou trop peu de réponses.
Le panneau de configuration NTP montre le mode de synchronisation utilisé par le
serveur ou sélectionné par le logiciel client NTP. Il montre ainsi les serveurs définis par
l’utilisateur ou détectés par le logiciel.
Description
La partie droite de cet écran montre la configuration actuelle utilisée par le logiciel client NTP:
26 MDE-LEDI-NETWORK-IN-4065V1.0
4. Interface WEB
FRANCAIS
Si vous sélectionnez la case Auto-detection, le LEDI Network IN essai d’utiliser les ser-
veurs GT NTP présents sur votre réseau et d’avoir le mode de synchronisation le plus
approprié. Si vous ne sélectionnez pas la case Auto-detection, vous devez indiquer
vous-même le mode de syncronisation et les serveurs NTP à utiliser.
La table suivante peut vous aider à choisir les paramètres les plus appropriés:
Nb de serveurs
Mode Description
NTP utilisés
One server 1 Utilise un seul serveur pour la synchronisation
Utilise le premier serveur au démarrage. Si ce ser-
veur est défaillant, commute sur le second serveur.
Two servers 2
Si le second est défaillant, commute sur le premier,
et ainsi de suite…
Utilise le premier serveur au démarrage. Si ce
serveur est défaillant, commute sur le second
Three servers 3
serveur. Si le second est défaillant, commute sur le
troisième, et ainsi de suite…
MDE-LEDI-NETWORK-IN-4065V1.0 27
4.2.5. Configuration des sorties
Quand vous cliquez sur le bouton Output, la configuration des sorties du LEDI Network
IN est affichée ainsi :
Ce panneau montre une vue synthétique des sorties du produit. Chaque sortie est pi-
lotée par une carte de sortie. L’affichage est considéré comme une sortie et est pilotée
par une carte d’affichage. Un LEDI Network IN peut contenir jusqu’à 4 cartes de sortie
en plus de la carte d’affichage.
28 MDE-LEDI-NETWORK-IN-4065V1.0
4. Interface WEB
FRANCAIS
Chaque carte de sortie peut-être configurée grâce aux paramètres suivant:
►► Vous pouvez désactiver la carte de sortie. Quand une carte est désactivée, le code
horaire n’est plus généré en sortie. Pour désactiver la sortie, cochez la case Deac-
tivate output.
►► Vous pouvez spécifier un fuseau horaire (un décalage) à appliquer sur la sortie de
la carte par rapport à l’heure UTC.
►► Vous pouvez spécifier une politque de changement d’heure (DST) à appliquer sur
la sortie de la carte par rapport à l’heure UTC.
MDE-LEDI-NETWORK-IN-4065V1.0 29
5. Interface SNMP
5.1. Présentation
►► Des variables peuvent être lue depuis un superviseur SNMP. Ces variables sont
stockées ensemble dans une base de données (MIB) organisée de manière hié-
rarchique. Les variables sont renseignées par le logiciel NTP pour refléter son état
interne.
►► Certains “traps” peuvent être générés par le logiciel NTP pour indiquer une impor-
tante modification d’état.
►► Une branche générale appelée System. Cette branche est compatible MIB II.
►► Une branche privée qui contient des informations spécifiques au produit LEDI
Network IN.
Les MIBs privées sont décrites avec des fichiers .MIB. Deux fichiers .MIB sont fournit sur
le CD-ROM dans le répertoire English\LEDINETWORKIN\MIB:
30 MDE-LEDI-NETWORK-IN-4065V1.0
5. Interface SNMP
FRANCAIS
Software
Cette branche contient toutes les informations concernant le logiciel client lui-même.
Voici la structure de la branche:
►► ntpCliHeader
Une courte description du produit. Il est du type GT LEDI Network IN client nnnnnn
Vxx.yy (aammjj) où xx.yy est la version courante du logiciel, aammjj est la date
d’émission du logiciel (jj/mm/aa) et nnnnnn est le numéro de série du produit.
►► ntpCliProduct
Une description du produit avec ses options qui doit être similaire au code produit
(décrit dans Annexe D – Guide des codes produits). Par exemple 9257/ AB........
D indique un LEDI Network IN avec des sorties IRIG-B et ASCII et un afficheur
(code D).
►► ntpCliVersionNumber
Version de ce produit. Il est du type Vxx.yy (aammjj) où xx.yy est la version actuelle
du logiciel, aammjj est la date d’émission du logiciel (jj/mm/aa)
MDE-LEDI-NETWORK-IN-4065V1.0 31
►► ntpCliSerialNumber
Numéro de série sur 6 chiffres.
►► ntpCliMAC
Adresse matérielle de l’interface Ethernet du LEDI Network IN. Cette adresse est de
la forme aa:bb:cc:dd:ee (6 octets binaires).
►► ntpCliMessageString
Description du dernier “trap” généré. Ce texte est lié au trap.
►► ntpCliResetInfo
Indication sur la raison du dernier redémarrage (reconfiguration ou RAZ manuelle).
►► ntpCliSoftwareState
Ce champ donne l’état actuel du logiciel client NTP. Il peut prendre l’une de ces
valeurs:
►► Idle: Le produit vient de démarrer.
►► Autodetection: aucun serveur NTP n’a été spécifié et le produit essaye de
détecter des serveurs NTP.
►► Autodetectfail: aucun serveur NTP trouvé pour la synchronisation – le produit
utilisera un serveur dès que vous en connecterez un sur le réseau.
►► Learning: le logiciel étudie actuellement les propriétés réseau.
►► ntpCliSyncMode
Le mode de synchronisation actif actuellement. Il peut prendre les valeurs suivantes :
►► Autodetect: aucun serveur NTP n’a été spécifié et le produit essaye de détecter
des serveurs NTP.
►► Sync1server: travaille avec un seul serveur NTP.
►► Sync2server: travaille avec deux serveurs NTP. Quand un serveur est dé-
faillant, il utilise l’autre.
►► Sync3server: travaille avec trois serveurs NTP. Quand un serveur est défaillant,
il utilise un des autres serveur.
►► ntpCliSyncSrvTable
Ce tableau contient tous les serveurs utilisés pour la synchronisation et d’autres in-
formations. Lma première entrée de la table est le serveur actuellement utilisé pour
la synchronisation. La seconde entrée est le second serveur préféré, etc. Chaque
entrée est de ce type :
►► ntpCliSyncSrvRank:
Rang du serveur. Un serveur de rang est est utilisé pour la synchronisation.
►► ntpCliSyncSrvAddress:
Adresse IP du serveur.
►► ntpCliSyncSrvAccuracy:
Précision du serveur comme fournit dans la trame NTP (du type 2^-x secondes).
32 MDE-LEDI-NETWORK-IN-4065V1.0
5. Interface SNMP
FRANCAIS
►► ntpCliSyncSrvUpSrvLoad (Serveur Gorgy Timing seulement)
Charge du serveur (nombre moyen de requêtes par secondes) fournit durant
l’étape d’auto-détection.
►► ntpCliSyncSrvPrefered (Serveur Gorgy Timing seulement)
Un numéro définit par l’utilisateur qui indique le rang de ce serveur. Quand
l’auto-détection est activée, le LEDI Network IN utilise le serveur de plus haut
rang.10
Hardware
La MIB décrit les cartes détectées et leurs configurations. Toutes les cartes de sortie et
l’afficheur sont connectés au même bus de sortie.
►► ntpOutBusCardTable
Une table qui montre toutes les cartes détéctées sur le bus de sortie. Chaque
carte est indéxéepar son adresse (1…9 pour les cartes de sortie et 9 pour l’affi-
cheur). Chaque entrée est de ce type.
10/ Voir la documentation du serveur NTP que vous utilisez pour configurer la préférence
MDE-LEDI-NETWORK-IN-4065V1.0 33
►► ntpOutBusCardIndex:
Index de cette entrée (adresse de la carte). Cette valeur peut prendre la valeur 1 à
8 pour une carte de sortie et 9 pour l’afficheur.
►► ntpOutBusCardState:
L’état de la carte. Il peut être detected pour indiquer que la carte fonctionne
correctement, failure si la carte ne répond pas ou scrambled si la réponse de la
carte est incorrecte.
►► ntpOutBusCardType:
Type de carte (voir Annexe D – Guide des codes produits pour la liste des types
de cartes de sortie possible).
►► ntpOutBusCardDescription:
Description de la carte.
►► ntpOutBusCardActivation:
Indique si la sortie de la carte est activée (activated) ou désactivée (deactiva-
ted) : l’activation de la carte peut être controllée par l’interface WEB.
Si la carte ne peut être désactivée, ce champs prend la valeur notapplicable.11
►► ntpOutBusCardTimeZone:
Fuseau horaire pour cette sortie. Il est donné comme un offset par rapport au
temps universel. Il peut-être changé par l’interface WEB.
►► ntpOutBusCardDayLightSavingPolicy:
Indique quelle politique de changement d’heure (DST) est utilisée. S’il n’y a pas
de DST, ce champs a la valeur <none>. Cette politique peut être changée via
l’interface WEB.
►► ntpOutBusCardDayLighSavingCurrent:
Indique si la politique de changement d”heure (DST) est en fonctionnement
(valeur summertime) ou pas (valeur wintertime). Si le DST n’est pas activé, ce
champs, ce chanmps a la valeur notapplicable.
►► ntpOutBusCardTotalOffset:
Indique le décalage total actuel par rapport à l’heure universelle UTC.
34 MDE-LEDI-NETWORK-IN-4065V1.0
6 Annexe A – Connexions
Cette annexe contient une description des différents connecteurs du LEDI Network
IN. Toutes les prises sont localisées à l’arrière du produit. Actuellement, seuls deux
FRANCAIS
types de sorties sont disponibles.
L’arrière du produit possède une prise d’alimentation standard, une prise Ethernet RJ45
et un bouton RESET comme ci-dessous:
+V DC
0V
MDE-LEDI-NETWORK-IN-4065V1.0 35
2. Sortie pour carte type ‘B’
(sortie double AFNOR/IRIG-B NFS87500)
Cette carte a sa sortie sur une simple prise 4 points. Le code AFNOR est disponible en
double sur cette sortie. Voici une vue schématique de la carte de sortie AFNOR/IRIG-B:
Le connecteur de sortie est localisé sur la face arrière du rack comme ci-dessous:
Voici les pattes du connecteur (le même signal est généré sur les sorties ½ et ¾):
Sortie 1 Sortie 2
1 2 3 4
36 MDE-LEDI-NETWORK-IN-4065V1.0
6 Annexe A – Connexions
FRANCAIS
Cette carte possède une prise 4 points et un connecteur DB9 La prise 4 points sort le TOP
de deux manières différentes et la prise DB9 fournit la trame horaire en sortie en niveau
RS-232 ou RS-485.
TXD
Driver de
Sortie RS-232
ligne RS-232
Driver de TX+
Sortie RS-485
ligne RS-485 TX-
Les connecteurs de sortie sont sur la face arrière du rack comme ci-dessous:
1 2 3 4
MDE-LEDI-NETWORK-IN-4065V1.0 37
Le connecteur DB9 a le format suivant:
5 4 3 2 1
9 8 7 6
TX-
38 MDE-LEDI-NETWORK-IN-4065V1.0
Annexe B – Format du code de sortie
Cette annexe contient une description du code horaire utilisé pour les différentes
sorties.
FRANCAIS
1. Carte Type ‘A’ (sortie ASCII+TOP)
►► La trame ASCII est générée au même moment que le PPS. Cette trame contient 23
caractères avec le format suivant :
STX D A Y D D / M M / Y Y H H : M M : S S CR
MDE-LEDI-NETWORK-IN-4065V1.0 39
2. Carte type ‘B’ (AFNOR/IRIG-B NFS87500)
2.1. Format de la trame
40 MDE-LEDI-NETWORK-IN-4065V1.0
Annexe B – Format du code de sortie
FRANCAIS
MDE-LEDI-NETWORK-IN-4065V1.0 41
Annexe C – Caractéristiques
1. Dimensions
424 mm
1U = 44 mm
263 mm 482 mm
2. Spécifications électriques
3. Autres spécifications
ARP,UDP,TCP,Telnet,ICMP,SNMP,DHCP,TFTP,
Protocoles supportés
HTTP,ENDMI, AutoIP, JAVA, SNTP client
Interface réseau 10Base-T avec interface RJ-45
Management SNMP, serveur WEB, Telnet, ENDMI
Mise à jour Possible par le serveur TFTP
Mémoire ROM:512K, RAM:128K, EEPROM:2K
42 MDE-LEDI-NETWORK-IN-4065V1.0
Annexe D – Guide des codes produits
1. Localisation de l’étiquette
FRANCAIS
L’étiquette qui identifie le produit se situe sur le dessus ou la face arrière du produit.
2. Informations de l’étiquette
GORGY TIMING
CODE 9257/Xopt
N° SERIE nnnnnn
La troisième ligne contient le numéro de série sur 6 chiffres (nnnnnn).
La seconde ligne est la description du produit:
9257/ X opt
Une ou plusieurs lettres (une lettre par sortie):
A ASCII+TOP
B IRIG-B/AFNOR NFS87500
Une lettre qui indique le type d’alimentation:
9 Pour courant continu 18 à 72V
0 Pour courant alternatif 230V 50Hz
Par exemple, le code 9257/9AB identifie un LEDI Network IN avec une alimentation cou-
rant continu 18/72V et deux sorties. La première sortie utilise le protocole ASCII, la secon-
deest une sortie IRIG-B/AFNOR.
MDE-LEDI-NETWORK-IN-4065V1.0 43
Annexe E – Documents complémentaires
Cette annexe contient quelques documents utiles pour gérer un ensemble de pro-
duits GT dans vote installation. Chaque document est une table que vous pouvez
librement copier et distribuer:
►► Description de l’installation: vous pouvez utiliser cette table pour créer une vue
synthétique de toute votre installation.
44 MDE-LEDI-NETWORK-IN-4065V1.0
Annexe E – Documents complémentaires
Description de l’installation
FRANCAIS
Date d’installation
Nom de l’installateur
MDE-LEDI-NETWORK-IN-4065V1.0 45
Annexe E – Documents complémentaires
Description de l’installation
Date d’installation
Nom de l’installateur
46 MDE-LEDI-NETWORK-IN-4065V1.0
NOTES
FRANCAIS
MDE-LEDI-NETWORK-IN-4065V1.0 47
5. Option chronomètre
SUPPORT TECHNIQUE
depuis la France sur un poste fixe :
support@gorgy-timing.fr
RADIO TIMING®, LEDI ®, LEDI CA®, HANDI ® sont des marques déposées GORGY TIMING.
Numéro de déclaration d’activité de prestataire de formation : 82 38 04877 38
GORGY TIMING RC 74 B 38 - Toutes modifications d'ordre technique ou esthétique peuvent être apportées sans préavis.
48 MDE-LEDI-NETWORK-IN-4065V1.0
ENGLISH
USER GUIDE
LEDI® Network in
MDE-LEDI-NETWORK-IN-4065V1.0 49
Important safety instructions
WARNING! Read the section that follows very carefully before installing your equi-
pment. It gives the safety instructions to follow during installation.
The electrical installation to which the equipment is connected must comply with
the NF C 15-100 standard.
This device does not have a primary power switch. A power protection system
(circuit-breaker or disconnecting switch), that is easy to access must be built into
the wiring installation. This device must support the nominal voltage and current
values specified on the clock.
All maintenance operation shall be conducted with power shut off, including sys-
tems connected on relay outputs if any.
Generally, the power cable (220V) and transmission cable (of time signal) shall
not be very close to each other, so as to avoid interference (keep the distance of
a few centimeters).
GORGY TIMING products are compliant with the following standards: CE, EN 60950,
EN 55022, EN 50024
50 MDE-LEDI-NETWORK-IN-4065V1.0
contents
1. inTRODUCtion........................................................................................................... 53
1.1. Quick installation................................................................................................................. 53
1.1.1. Check the package content..................................................................................... 53
1.1.2. Connect the product................................................................................................ 54
1.2. Set-up your product............................................................................................................. 54
2.1.1. Manual network configuration.................................................................................. 54
2.1.2. Output cards configuration...................................................................................... 55
1.3. Basics.................................................................................................................................. 55
1.3.1. Synchronization concepts........................................................................................ 55
A/ Clock Correction principles...................................................................................... 55
B/ Network dialog......................................................................................................... 57
C/ Working with several servers.................................................................................. 57
1.3.2. The NTP client software.......................................................................................... 58
ENGLISH
2. FULL SETUP................................................................................................................ 59
2.1. Network configuration.......................................................................................................... 59
2.1.1. Default configuration................................................................................................ 59
2.1.2. Changing network parameters................................................................................ 59
2.1.3. Integration in your network...................................................................................... 61
2.2. Output cards configuration ................................................................................................. 62
2.2.1. Introduction.............................................................................................................. 62
2.2.2. Default configuration................................................................................................ 62
2.2.3. Change the settings................................................................................................. 62
4. WEB INTERFACE......................................................................................................... 67
4.1. Presentation........................................................................................................................ 67
4.2. Description of the WEB interface......................................................................................... 68
4.2.1. Ecran Principal........................................................................................................ 68
4.2.2. Standard setup........................................................................................................ 69
4.2.3. SNMP setup ........................................................................................................... 72
4.2.4. NTP Setup............................................................................................................... 74
4.2.5. Output and display setup......................................................................................... 76
4.3. WEB interface of NTP server output card........................................................................... 79
4.3.1. Network and SNMP setup Status bar...................................................................... 79
4.3.2 NTP setup Description.............................................................................................. 80
5. SNMP INTERFACE....................................................................................................... 82
5.1. Presentation........................................................................................................................ 82
5.1.1. Structure of the private MIB for LEDI Network IN.................................................... 83
5.1.2. Description of the SNMP traps................................................................................ 87
5.2. SNMP interface for NTP server card................................................................................... 88
5.2.1. Software information MIB for the NTP server outcard............................................. 88
5.2.2. Description of the SNMP traps................................................................................ 92
MDE-LEDI-NETWORK-IN-4065V1.0 51
APPENDIX A – CONNECTIONS...................................................................................... 93
1. Connection for all products..................................................................................................... 93
1.1. 230V and 115V AC product (type ‘0’)......................................................................... 93
1.2. 18/72V DC product (type ‘9’)...................................................................................... 93
2. Dual AFNOR/IRIG-B NFS87500 output (‘B’ type).................................................................. 94
3. Dual AFNOR/IRIG-B NFS87500 DCLS RS422 and TTL output (‘T’ type).............................. 95
4. RS232 and 485/422 ASCII+TOP (‘A’ and ‘R’ type)................................................................. 96
5. TOP / ALARM output (‘A’, ‘R’ type and ‘G’ type) .................................................................... 97
5.1. Pin-out........................................................................................................................ 97
5.2. Examples of how to use the open collector output (pins 3-4)..................................... 98
5.3. Example of how to use the static relay output (pins 1-2)............................................ 99
APPENDIX E – DATA......................................................................................................110
1. Measurements...................................................................................................................... 110
2. Specifications....................................................................................................................... 110
3. Autres spécifications............................................................................................................. 110
3. Stamp contents......................................................................................................................111
52 MDE-LEDI-NETWORK-IN-4065V1.0
1. inTRODUCtion
This document is a user’s guide for the LEDI Network IN. This product is a NTP client. The
purpose of this device is to synchronize various equipments using a reference time from
one or several NTP servers. You can see this product as a kind of converter that translates
a “NTP signal” to a traditional synchronization signals (ASCII+TOP, AFNOR, IRIG-B for
example).
Using the LEDI Network IN for synchronization provides you with several advantages:
►► You can use the installed network architecture with the well-known protocols
Ethernet+TCP/IP
►► L’installation est simple.
ENGLISH
►► You can change Simplified set-up.
►► The product is a 19” 1U rack that can be easily installed on your installation.
EBy using a Gorgy Timing server in combination with the LEDI Network IN you greatly
improve the ease of installation and use.
This part contains the minimum information for the set-up of the LEDI Network IN. You can
find additional information in part 3.
►► A network cable
☛☛Contact your dealer if one of the items above isn’t in the package.
MDE-LEDI-NETWORK-IN-4065V1.0 53
1.1.2. Connect the product
►► It is highly recommended that you notice the serial number (written on identification
stamp), the localization and a short description for the product. The table in You can
use the table in Appendix F – Additional documents
►► Connect the LEDI Network IN to your network using the network cable.
►► Connect the LEDI Network IN to a power supply using the power supply cable when
it is present.
Your system should work immediately if you use Gorgy Timing NTP server(s) and there
is a DHCP server on your network. After a 2 minutes learning stage, the LEDI Network
IN activates its outputs and begin to delivers UTC time.
However, Gorgy Timing recommends you to fill-in for each product its physical locali-
zation. This is possible using the GTNetMng tool localized on the CD-ROM. For more
information, see part 31.2.
Gorgy Timing NTP products are configured in factory to automatically get an IP address.
Two mechanisms are used:
1. If a DHCP server is present on your network, our products get an address automa-
tically. This ensures that the IP address is compatible with your network.
1/ For example, you may not have the possibility to configure the LEDI Network IN from a WEB navigator
54 MDE-LEDI-NETWORK-IN-4065V1.0
1. inTRODUCtion
The default DHCP identifier is CRnnnnnn (nnnnnn is the serial number of the product).22
You can change this identifier with the GTNetMng tool or through the WEB interface as
described in part 31.2 and 52.2
If you don’t have a DHCP server or you want to configure yourself the network parame-
ters, use the GTNetMng tool on the CDROM to change the network parameter. Please
refer to part 31.2 for more information.
ENGLISH
2.1.2. Output cards configuration
The default configuration for all the output cards is to deliver UTC time. The time recei-
ved from the NTP server is directly sent to the output.
Each card can be configured to output several local times. This configuration is done
through a WEB browser (see part 32).
1.3. Basics
This part contains a description of the basic concepts of the product LEDI Network IN. It
helps you to understand the behavior of the product under various circumstances.
The NTP client software is the very heart of the LEDI Network IN. It performs all the syn-
chronization, the management of the hardware and provides information for the WEB inter-
face and the SNMP protocol.
2/ Some DHCP servers have the ability to copy the DHCP name into the DNS. In this case, you can access the
LEDI Network IN directly by its DHCP name instead of its IP address.
MDE-LEDI-NETWORK-IN-4065V1.0 55
Heure serveur
Dérive nulle
Heure serveur
Heure client
Heure client
To perform this synchronization, the NTP client software permanently compares the two
clocks and
Evolution computes
dans le tempsthe following information:
►► Offset:
It’s the difference between the time of the server clock and the time of the client
clock. For example, if the server clock indicates 2:10:13 and the client clock indica-
tes 2:11:14, the offset is –1:01.Heure serveur
►►Dérive
Drift: constante Heure serveur
It’s the frequency difference between the two clocks. When drift is not null and
Heure client
without clock correction, the offset between the two clock increase or decrease
Heure client
depending on the drift sign.3
The following figure shows how the evolution of the two clocks with or without drift:
server time
Drift is null :
server time
client time
client time
server time
server time
Drift is constant :
client time
client time
3/ There are several reasons for the presence of a drift between two clocks: generally the drift is due to the tempe-
rature difference between the two clocks.
56 MDE-LEDI-NETWORK-IN-4065V1.0
1. inTRODUCtion
B/ Network dialog
The real drift and offset of the LEDI Network IN clock related to the NTP server are es-
timated from a measured offset. This offset is computed by subtracting the client clock
date from the server clock date.
Periodically, the client estimate current offset from the server. This measure is done
using a message-passing mechanism as shown on following figure:
ENGLISH
Query server date
On a LAN, it takes some milliseconds between the time when the client asks for the
date and the time when it receives the reply. This time is due to transmission delay
on the network. It can vary because of network load or NTP server load. Worse, the
transmission time from client to server is generally not the same that the one from the
server to client.
Actually, on a large period of time, the difference of sum of client-server and server-client
transmission delays is zero. The NTP client algorithm implemented in the LEDI Network
IN is designed to compensate transmission delay and to average the measures.
MDE-LEDI-NETWORK-IN-4065V1.0 57
1. inTRODUCtion
Learning
Auto-detecon environment
Learning
environment
Learning
Enable outputs
No reply
Tracking Commung
Commuta�on OK
►► Auto-detection:
Server auto-detection is activated. The NTP client tries to find Gorgy Timing ser-
vers. At least one detected server is required to leave this state;
►► Learning:
The NTP client software has found one or several Gorgy Timing (auto-detection ac-
tivated) or works with configured servers. In this state, the software learns network
properties. About 2 minutes are required to complete this stage;
►► Tracking:
Normal behavior, the NTP client permanently evaluate its offset and drift with the
server;
►► Commuting:
Not enough reply received from current server, trying another server.
58 MDE-LEDI-NETWORK-IN-4065V1.0
2. FULL SETUP
This part contains information for a full configuration of the product. It should be
used for fine network configuration and output cards set-up
ENGLISH
►► If a DHCP server is installed on the network, it record the DHCP name and return an
IP address. The LEDI Network IN starts working with this address.
The default DHCP identifier of the product is CRnnnnnn with nnnnnn, the serial number
on 6 digits. The serial number is written on the identification stamp on the top or on the
bottom of the product.
The default SNMP name of the product (that can be seen from a SNMP browser (see
part 6) or from a WEB browser) is LediNetwkINnnnnnn with nnnnnn, the serial number
on 6 digits.
Use the GTNetMng tool provided on the CDROM to configure your device:
►► Insert the CDROM in the drive. Start the GTNetMng tool that is localized in the
directory Common\Configuration44
4/ For example, if your CD reader has letter E:, the GTNetMng tool is localized in E:\Common\Configuration\
GTNetMng.exe
MDE-LEDI-NETWORK-IN-4065V1.0 59
►► The GTNetMng tool displays automatically the Gorgy Timing products installed
on your network. Each line contains information about one connected product as
shown below:
Name, serial number Current Ip address network mask MaC address DHCp identifier
and localization
►► Double-click on the line related to the product you want to configure. The following
panel is displayed:
►► Set the network parameters and physical localization and click the Set! button.
60 MDE-LEDI-NETWORK-IN-4065V1.0
2. FULL SETUP
You don’t have to change any network setting for the following cases:
►► You have a DHCP server and enough reserved IP address for the product.
►► You don’t have a DHCP server but you don’t need to access to the device through
its WEB or SNMP interface. In this case, the AutoIP mechanism will automatical-
ly affect an IP address but this address will probably be incompatible with your
network.
ENGLISH
Some DHCP servers have the capacity to register the device in the DNS. In this
case, the registered name is the DHCP identifier. Then, you can access to the device
from your WEB or SNMP browser. For example if you give the DHCP name ntpin3 to
your LEDI Network IN, you can simply type ntpin3 in the address field of your WEB
browser.
MDE-LEDI-NETWORK-IN-4065V1.0 61
2.2. Output cards configuration
2.2.1. Introduction
Your LEDI Network IN is provided with up to 4 output cards. Each output card is tightly
synchronized on the NTP time code received from the NTP server. Each card acts as
a kind of translator that receives time from the NTP software and output specific time
code.
Currently, there are 6 kinds of cards:
You can freely use and copy the table Devices configuration in Appendix F – Additional
documents.
When you receive this product from Gorgy Timing, all the output cards are configured to
output UTC time and time is constant all along the year (no Day Saving Time correction).
The display is managed as an output cards and can be configured in the same way..
Open the WEB site of the LEDI Network IN (see part 5). Click on the button.
The current configuration of your product appears at the screen (shown below for a 9257/
A model):
62 MDE-LEDI-NETWORK-IN-4065V1.0
2. FULL SETUP
ENGLISH
In this screen you can tune each card independently (see part 5.2.5). When you have
change.the settings, click on the . button. The modification should appear imme-
diately at the outputs or on the display.
You can add a NTP server output card to your LEDI network IN. By this way, you can
synchronize your local network on this card, which is itself synchronized by the NTP
client on a remote Internet NTP server.
The NTP server card has to be configured by the same way than the NTP client of the
LEDI Network IN. Its default network configuration is DHCP mode with identifier SC-
nnnnnn with nnnnnn, the serial number on 6 digits.
The default SNMP name of the NTP server (that can be seen from a SNMP browser or
from a WEB browser) is NTPServnnnnnn with nnnnnn, the serial number on 6 digits.
To change the network parameters of the NTP server card, use the GTNetMng tool :
see page 10). Like the NTP client, the NTP server card provides a WEB page for fine
configuration (see page 31) and a SNMP MIB for supervision through the network (see
page 40).
MDE-LEDI-NETWORK-IN-4065V1.0 63
3. FRONT DISPLAY INTERFACE
The front display interface can display up to 16 characters. Two buttons provides
you with display configuration and global reset. The LEDI Network IN uses the front
display to show current time and different alarm condition.
►► When the device start, all the dots of the displays are lightened.
►► If no server is configured by the user, the LEDI Network IN try to detect GT servers
and display the following message:
►► If the auto detection stage fails, the following text is displayed until a GT server is
available on the network:
64 MDE-LEDI-NETWORK-IN-4065V1.0
3. FRONT DISPLAY INTERFACE
►► If there is at least one GT server or the user has configured manually the servers,
the LEDI Network IN enters learning stage and displays the following text:
ENGLISH
3.2. Time display
When no alarm is present and the LEDI Network IN is correctly synchronized on a server,
the current time of the server is permanently displayed. The display alternatively shows
time and date as shown below:
►► When displayed is configured to display UTC time, the following information are
alternatively displayed:
►► When displayed is configured to display local time, the following information are
alternatively displayed:
MDE-LEDI-NETWORK-IN-4065V1.0 65
3. FRONT DISPLAY INTERFACE
The commuting alarm indicates that the server currently used for synchronization does not
reply (or does not reply correctly). In this case, the LEDI Network IN tries another server.
The display alternatively shows time (as described in previous part) and the following text:
66 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB INTERFACE
4.1. Presentation
The LEDI Network IN can be configured and supervised through a WEB interface. This
interface provides you with the following features:
ENGLISH
►► Management and diagnostic of output cards.
Each LEDI Network IN has its own WEB server that delivers WEB pages. The WEB site
is a JAVA applet; if needed, you can find a JVM on the CDROM in the directory Common\
JAVA.
To access the WEB site, type-in the address of the LEDI Network IN in the address field of
your WEB browser (as shown below) and validate the input5.
It takes about 20 seconds to load of the JAVA applet. If the load fails, it can be for one of
the following reasons:
For the first two reasons, you have to check for the IP address of the LEDI Network IN and
your network configuration. For the last reason, you have to install the JVM (see directory
Common\JAVA on the CDROM).
5/ If you have configured your LEDI Network IN in DHCP mode and that your server automatically register DHCP
name in the DNS, you can also use the DHCP name instead of the IP address
6/ Check especially the configuration of your Internet Explorer.
MDE-LEDI-NETWORK-IN-4065V1.0 67
4.2. Description of the WEB interface
This is the screen that appears when accessing the WEB site of the LEDI Network
IN. The first four buttons at the left of the screen provide an access to the following
panels:
1. Standard: information about the product and configuration of network parameters
See part 2.2.
2. SNMP: configuration of SNMP parameters;
3. NTP: diagnostic and configuration of the NTP software behavior;
4. Output: diagnostic and configuration of output cards and display.
The Set Up! button updates immediately the LEDI Network IN configuration. The confi-
guration is stored permanently in an EEPROM.
68 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB Interface
When you click the Standard button, the network parameters and product information
are displayed as shown below:
ENGLISH
In the top of the panel, you can control the network parameters and the WEB access
password. In the bottom of the panel, you have information about the product.
Network parameters
WARNING. If you click on the Set Up! button after changing one or
several network parameter(s), the LEDI Network IN must restart to
use the network parameters. During the reset and 2 minutes after,
the output(s) of the product is(are) disabled.
►► IP mode
Indicate if the LEDI Network IN works with a fixed IP (set in the field IP address) or
use DHCP protocol (the DHCP identifier is set in the field DHCP identifier);
MDE-LEDI-NETWORK-IN-4065V1.0 69
►► IP address
Indicate the network address affected to the device. An IP address is made of four
numbers separated by a dot. Each number range from 0 to 255;
►► DHCP identifier
Identifier to be used when the LEDI Network IN is configured in DHCP mode. This
identifier has 8 letters maximum. The default value is CRnnnnnn (where nnnnnn is
the serial number on 6 digits);
►► Network submask
Indicate the width of the network you use. For example, a network submask
255.255.255.0 indicates that only the last number change (in the example above,
address in the network can change between 192.168.10.1 to 192.168.10.254)7.
►► Gateway address
If you want the LEDI Network IN to communicate with devices outside the local
network, you must indicate a gateway that will be used to go outside local network;
►► Without gateway
Check this box when you don’t have a gateway on your network (or don’t want to
use it);
Product information
►► Firmware Description
Short text that describes which software is running on your product
7/ If you configure several devices to communicate on the same network, you must have the same network submask.
70 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB Interface
ENGLISH
If you want to protect access to the parameters of the LEDI Network IN, you can specify
a password. This is done by enter the password twice in the area Enter password and
Confirm password (the same password in the two areas).
If you don’t want to protect the parameters, check the box Without password.
When a password is set, it will be asked to the user at the next connection. In this case, the
main screen looks like follows:
Status bar
The status bar is positioned on bottom of the WEB page. It gives information about the NTP
client software. It contains the following information:
MDE-LEDI-NETWORK-IN-4065V1.0 71
4.2.3. SNMP setup
When you click the SNMP button, the SNMP parameters are displayed as shown below:
The very standardized SNMP protocol provides a means to get information and alarms
from the LEDI Network IN.8 Access to these information (the MIB) can be “protected” by
a keyword that is the Community Name.
Alarms are sent to a SNMP browser localized on a computer identified by its IP ad-
dress. Up to 5 IP Trap address can be specified that allows the alarm monitoring from
5 different computers.
Last, the SNMP related name, location and contact could be configured in this screen.
These information are stored in the system branch of the MIB and can be displayed in
a SNMP browser or in the GTNetMng tool (see part 31.2).
For convenience, alarms can be notified through the SYSLOG protocol that is more
often implemented under UNIX®.
72 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB Interface
Description
ENGLISH
►► SYSLOG File Id
Identify the file to use on remote computer for SYSLOG protocol;
►► Community name
A simple keyword that is needed in a SNMP browser to access SNMP information.
This keyword must have 8 letter at the most;
►► System name
A text that you can use to give a name to the LEDI Network IN. This name appears
in the sysName variable of the system branch of the MIB. The initial value is Ledi-
NetwkINnnnnnn (where nnnnnn is the serial number of the product);
►► System location
A text that you can use to indicate the physical localization of the LEDI Network IN.
This name appears in the sysLocation variable of the system branch in the MIB.
There is no initial value.
►► System contact
A text that you can use to indicate the person to contact for any problem related to
this LEDI Network IN. This name appears in the sysContact variable of the system
branch in the MIB. There is no initial value.
dentifie le fichier à utiliser sur l’ordinateur distant pour le protocole SYSLOG.
MDE-LEDI-NETWORK-IN-4065V1.0 73
4.2.4. NTP Setup
When you click the NTP button, the configuration of the synchronization of the LEDI
Network IN is displayed as shown below:
The LEDI Network IN can be synchronized on up to three NTP servers. In fact, the NTP
software uses only one server at the same time but can commute to another server
when there is no or not enough reply.
The NTP configuration panel shows what is the synchronization mode used by the
server or selected by the NTP software. It also shows the servers defined by the user
or detected by the software
Description
The right part of this screen shows the current configuration used by the NTP client
software:
IIt shows the different servers used for synchronization and the current synchronization
mode (on the screenshot above, there is only one server at IP address 192.168.10.124).
In addition, this screen part shows what is the server currently used for synchronization
(with a frame labeled Active). If a commutation is in progress, the label Trying is dis-
played nears the related NTP server. :
74 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB Interface
The left part of the NTP screen allows you to configure the synchronization mode and
the NTP servers used:
ENGLISH
If you select the checkbox Auto-detection, the LEDI Network IN try to use the GT NTP
servers present on your network and use the more appropriate synchronization mode.
If you don’t select the checkbox Auto-detection, you have to indicate the synchroniza-
tion mode and the NTP servers to use.
The following table can help you to select the more appropriate parameters:
# of NTP servers
Mode Description
used
One server 1 Use only one server for synchronization
Use the first server at startup. If this server fails,
Two servers 2 commute to the second server. If this server fails,
commute to the first one and so on…
Use the first server at startup. If this server fails,
Three servers 3 commute to the second server. If this server fails,
commute to the third one and so on…
MDE-LEDI-NETWORK-IN-4065V1.0 75
4.2.5. Output and display setup
When you click on the Output button, the configuration of the output of the LEDI Network
IN is displayed as shown below:
This panel shows a synthetic view of the outputs of the product. The display is conside-
red as an output and is driven by a display card. A LEDI Network IN can contain up to 4
output cards plus the display card.
The display and each output cards can be configured independently using the right
cyan box. When an output card is not present or in failure, its box doesn’t appear.
You can freely use and copy the table Devices configuration in Appendix F – Additional
documents.
76 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB Interface
DST policy
ENGLISH
Offset to apply to UTC time
The previous picture shows the configuration panel for an AFNOR/IRIG-B. In addition,
the description contains identification and version of the program embedded in the out-
put card (there, it’s the program NTPSAFN1, version 0252).
Each output card can be configured independently through the following parameters :
►► Output deactivation
Except the display, all the output cards can be deactivated. The deactivation has
the following effects :
►► For ASCII+TOP card, the time frame is not generated and the TOP outputs are
in the open state;
►► For AFNOR output, the carrier is not modulated.
►► The ALARM output doesn’t generate warning signal.
►► Time Zone
The “Time Zone” is a time offset that can be added or subtracted from the time
received through the NTP protocol (which is UTC time) to generate local time. For
example in France, local time is GMT + 1:00.
MDE-LEDI-NETWORK-IN-4065V1.0 77
Here are the different DST policies :
You can configure here the period and the width of the TOP.
To configure the different alarm signals, choose an alarm type (no alarm, synchronization
failure, power failure, synchronization + power failure) then set the period and width of
the signal. Do the same for each alarm type.
78 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB Interface
If your product is provided with a NTP server card, the following panel will be displayed:
Offset from UTC cannot be configured, as the card deliver NTP time code in UTC. To
configure finely the NTP server card, you need to open its own WEB page, described
in the following chapter.
ENGLISH
4.3. WEB interface of NTP server output card
To configure network and SNMP parameters, the NTP server output card provides the
same WEB panels than the LEDI Network IN (see below). Please refer to parts 2.2 and
2.3 for more details. The NTP server MIB is detailed in page 40.
Status bar
The status bar is positioned on bottom of the WEB page. It gives information about the NTP
server software. It contains the following information:
MDE-LEDI-NETWORK-IN-4065V1.0 79
4.3.2 NTP setup
When you click the NTP button, the configuration of the NTP server software of the
output card is displayed as shown below:
Description
►► STRATUM level
the stratum value to be stored in the NTP messages sends to the NTP clients.
►► Reference ID
A 4 letters identifier that gives information about the time reference. This value is put
in the appropriate field in the NTP frame
►► Security threshold
Give the maximum allowed phase difference (in seconds) before locking the NTP
server software. This field is initialized to 65536.0
80 MDE-LEDI-NETWORK-IN-4065V1.0
4. WEB Interface
►► RFC868 compatibility
Specify the kind of compatibility with RFC868 : Not compatible, UDP Time server
or TCP Time server
►► Lock control
This checkbox allows the user to control the lock state of the LEDI Network Enhan-
ENGLISH
ced. When checked, the NTP server is locked and doesn’t deliver NTP or output
signal. When cleared the NTP server is working.
►► Preference
A number that allow you to prioritize your different Gorgy-Timing NTP servers. By
this way, the server with the highest preference number is chosen in priority by
Gorgy-Timing NTP clients.
9/ Time code is not present (server is autonomous) or the received time-code indicates that external synchroniza-
tion is lost
MDE-LEDI-NETWORK-IN-4065V1.0 81
5. SNMP INTERFACE
5.1. Presentation
The LEDI Network IN provides a SNMP v1 interface for fine monitoring and diagnostic.
The SNMP protocol allows the supervision of a device through the network. Two kind of
information are available through a SNMP interface:
►► A set of variables that can be read. These variables are stored together in a databa-
se (MIB) organized in a hierarchical way. The variables are set by the NTP software
to reflect its internal states.
►► Some traps that can be generated by the NTP software to indicate important state
modification.
►► A private branch that contains information specific to the LEDI Network IN product.
Private MIBs are described with .MIB files. Two .MIB files are provided on the CDROM in
the directory English\LEDINETWORKIN\MIB:
►► The file GtNtpOutBus.mib contains the description of the information related to the
output cards – Localization in the MIB:
iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).hardware(2).ntpOutBus(1)
►► The file GtNtpClient.mib contains the description of the information related to the
NTP client software – Localization in the MIB:
iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).software(1).ntpClient(4)
►► The file GtNtpServer.mib contains the description of the information related to the
NTP server output card software – Localization in the MIB:
iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).software(1).ntpSrv(3)
82 MDE-LEDI-NETWORK-IN-4065V1.0
5. SNMP INTERFACE
Software
This branch contains all the information related to the client software itself. Here is the
structure of this branch:
ENGLISH
The different fields of this branch are described below:
►► ntpCliHeader
A short description of the product. It should be something like GT LEDI Network IN
client nnnnnn Vxx.yy (yymmdd) where xx.yy is the current version of the software,
yymmdd is the release date of the software (dd/mm/yy) and nnnnnn is the serial
number of the product.
►► • ntpCliProduct
A description of the product with its options that should be similar to the product
code (described in Erreur ! Source du renvoi introuvable.). For example 9257/
AB........D indicates a LEDI Network IN with IRIG-B and ASCII outputs and a display
(code D).
MDE-LEDI-NETWORK-IN-4065V1.0 83
►► ntpCliVersionNumber
Version of this product. It’s something like Vxx.yy (yymmdd) where xx.yy is the
current version of the software, yymmdd is the release date of the software (dd/
mm/yy)
►► ntpCliSerialNumber
Serial number of this product on 6 digits.
►► ntpCliMAC
Hardware address of the Ethernet interface of the LEDI Network IN. This address is
on the form aa:bb:cc:dd:ee (6 binary bytes).
►► ntpCliMessageString
A text that gives the description of the last generated trap. This text is also attached
to the trap.
►► ntpCliResetInfo
A text that indicates why the product has restarted (reconfiguration or hard reset).
►► ntpCliSoftwareState
This field gives the current state of the NTP client software. It can take one of the
following values:
►► Idle: the product has just started.
►► Autodetection: no NTP server has been specified and the product is trying to
detect NTP server(s).
►► Autodetectfail: no NTP server found for synchronization – the product will use a
server as soon as you connect a server on your network.
►► Learning: the software is currently learning network properties.
►► ntpCliSyncMode
The synchronization mode currently used. It can be one of the following values:
►► Autodetect: no NTP server has been specified and the product is trying to detect
NTP server(s).
►► Sync1server: works with only one NTP server.
►► Sync2server: works with two NTP servers. When a server fails, it uses the other
one.
►► Sync3server: works with 3 NTP servers. When a server fails, it uses one of the
other servers.
84 MDE-LEDI-NETWORK-IN-4065V1.0
5. SNMP INTERFACE
►► ntpCliSyncSrvTable
A table that contains all the servers used for synchronization and information. First
entry in the table is server being used for synchronization. Second entry is the pre-
ferred second server, etc. Each entry has the following format:
►► ntpCliSyncSrvRank:
rank of the server. Server of rank 1 is used for synchronization.
►► ntpCliSyncSrvAddress:
IP address of the server.
►► ntpCliSyncSrvAccuracy:
Accuracy of the server as returned in the NTP frame (something like 2^-x se-
conds).
ENGLISH
►► ntpCliSyncSrvUpAccuracy (Gorgy Timing server only)
Accuracy of the server as returned during auto-detection stage.
►► ntpCliSyncSrvUpSrvLoad (Gorgy Timing server only)
Load of the server (average number of requests per second) as returned during
auto-detection stage.
►► ntpCliSyncSrvPrefered (Gorgy Timing server only)
A number that indicates a user-defined rank attached to this server. When auto-de-
tection is activated, the LEDI Network IN takes the server with higher rank.
MDE-LEDI-NETWORK-IN-4065V1.0 85
Hardware
The MIB describes which card is detected and what is the configuration for the cards.
All the output cards and the display are connected to a same output bus.
►► ntpOutBusCardTable
A table that shows all the cards detected on the output bus. Each card is indexed by
its address (1..8 for output cards and 9 for the display). Each entry has the following
format:
►► ntpOutBusCardIndex:
Index of this entry (i.e card address). This value can have a value from 1 to 8 (for
output cards) or 9 (for display);
►► ntpOutBusCardState:
The state of the card. It can be detected that indicate that the card works cor-
rectly, failure if the card don’t reply or scrambled if the reply from the card is
incorrect;
►► ntpOutBusCardType:
Type of the card (see Erreur ! Source du renvoi introuvable. for a list of the
possible output cards types);
►► ntpOutBusCardDescription:
A textual description of the card;
86 MDE-LEDI-NETWORK-IN-4065V1.0
5. SNMP INTERFACE
►► ntpOutBusCardActivation:
Indicate if the output of the card activated or deactivated (this feature can be
controlled from the WEB interface). If the card cannot be deactivated, this field
has the value notapplicable;
►► ntpOutBusCardTimeZone:
Time-zone for this output. This is displayed as an offset from universal time. This
setting can be changed from the WEB interface;
►► ntpOutBusCardDayLightSavingPolicy:
Indicate which day saving time policy is used. If there is no DST, this field has
the value <none>. This setting can be changed from the WEB interface;
►► ntpOutBusCardDayLighSavingCurrent:
ENGLISH
Indicate if Day Saving Time is in effect (value summertime) or not (value winterti-
me). If Day Saving Time is not activated, this field has the value notapplicable;
►► ntpOutBusCardTotalOffset:
Indicate current total offset from UTC.
Here is an example of the description of the output cards displayed in a SNMP browser:
MDE-LEDI-NETWORK-IN-4065V1.0 87
5.2. SNMP interface for NTP server card
The NTP server card provides its own a SNMP v1 interface for fine monitoring and diagnos-
tic. Its private MIB is described in the file GtNtpServer.mib provided on the CDROM in the
directory English\LEDI Network IN\MIB.
iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).gorgy(8955).software(1).ntpSrv(3)
General organization
This branch contains all the information related to the server software itself. Here is the
structure of this branch:
General information
88 MDE-LEDI-NETWORK-IN-4065V1.0
5. SNMP INTERFACE
General information
►► ntpSrvHeader
Short description of the NTP server output card.
►► ntpVersionNumber
Version and release date of the NTP server firmware
►► ntpSrvSerialNumber
Serial number of the Ethernet interface (unique for each device)
ENGLISH
►► ntpSrvMAC
Address of the Ethernet interface (MAC address)
►► ntpSrvMessageString
A text bound with each generated trap. It contains the text bound to the last gene-
rated trap.
►► ntpSrvResetInfo
A text that gives the reason of the last RESET.
►► ntpSrvFailure
true(1) if there is no time code and that the NTP output is deactivated
false(0) if the time code is present or the NTP server software can guarantee the
accuracy; NTP output is activated
►► ntpSrvLockedOnSecurity
true(1) if a time difference too important has been detected between the NTP
software clock and the time returned by the hardware, for security reasons, the NTP
server is currently locked
false(0) if no significant time difference has been detected
►► ntpSrvLockedManually
true(1) if the software has been locked by a user
false(0) if the software is not locked by a user
►► ntpSrvRescaleAmount
A text that gives the amount of the difference between NTP software clock and
hardware time that leads to a security lock
unit: second
MDE-LEDI-NETWORK-IN-4065V1.0 89
►► ntpSrvRescaling
true(1) if the NTP server software is currently rescaling on the hardware. During
rescaling stage, the NTP server don’t reply to clients
false(0) if no rescaling in progress
►► ntpSrvRequiredAccuracy
A text that gives the required accuracy for this NTP software (related to the time
provided by the hardware)
unit: seconds
NTP server outcard: this accuracy is fixed to 0.24414 ms (4096-1 s)
►► ntpSrvSecurityThreshold
A text that gives the maximum accepted difference between software clock and
hardware time before locking the server
unit: seconds
NTP server outcard: this value is initialised to 65535.0 seconds
►► ntpSrvNbNtpRequests
Total number of received NTP requests (in fact all the requests received on port
123). When this counter reaches 32767, it reloops to 0.
►► ntpSrvNbRjectedRequests
Number of rejected NTP requests. A request can be rejected if it bad-formed, en-
cryption is invalid or the NTP server is locked. When this counter reaches 32767, it
reloops to 0.
►► ntpSrvRequestsRate
Shows an approximation of the average number of requests per seconds.
►► ntpSrvNbTcpTimeRequests
Total number of received TCP Time requests. When this counter reaches 32767, it
reloops to 0.
►► ntpSrvNbUdpTimeRequests
Total number of received UDP Time requests. When this counter reaches 32767, it
reloops to 0.
90 MDE-LEDI-NETWORK-IN-4065V1.0
5. SNMP INTERFACE
It gives information on an external time reference used by the hardware (for example
an antenna).
►► ntpSrvExternallySynchronized
notapplicable(2) if there is no information on external time reference
true(1) if the hardware is correctly synchronized on its external time reference
false(0) if the hardware is not synchronized on its external time reference (out of
radio coverture?)
ENGLISH
►► ntpSrvSyncLostDuration
Number of seconds since beginning of synchronisation lose or duration of last syn-
chronisation lose
►► ntpSrvStratumLevel
Current stratum level. This is the value returned to the NTP client.
This value can change when the synchronisation is lost depending on the policy
defined in the setup.
Moreover, the default value can be changed through the setup.
►► ntpSrvLIValue
Current LI value. This is the value returned to the NTP client.
This value can change when the synchronisation is lost depending on the policy
defined in the setup.
►► ntpSrvAutonomous
true(1) if the NTP software is using its own clock to deliver time through the NTP
false(0) if the NTP software is using time code from its synchronisation input
►► ntpSrvAutonomous
If ntpSrvAutonomous=false, give number of seconds that the server can works
without time code at its input
If ntpSrvAutonomous=true, give number of remaining seconds before stopping
synchronizing equipment through NTP
Other texts are possible (for example when there is no possible autonomy)
MDE-LEDI-NETWORK-IN-4065V1.0 91
5.2.2. Description of the SNMP traps
92 MDE-LEDI-NETWORK-IN-4065V1.0
APPENDIX A – CONNECTIONS
This appendix contains a description of the different connectors of the LEDI Network
IN. All the plugs are localized on the backside of the product.
The backside of the product has a standard power supply plug, the Ethernet RJ45 plug
ENGLISH
and a RESET button as shown below:
The Ethernet connector and the RESET button are the same.
Only the power supply plug is different.
+V DC
0V
MDE-LEDI-NETWORK-IN-4065V1.0 93
2. Dual AFNOR/IRIG-B NFS87500 output (‘B’ type)
This card has its output on a single 4 points plug. The AFNOR code is available twice on
this output. Here is a schematic overview of the AFNOR/IRIG-B output card:
The output connector is localized on the back side of the rack and is shown below:
Here is the pin-out of the connector (the same signal is generated on outputs ½ and ¾) :
Output 1 Output 2
1 2 3 4
94 MDE-LEDI-NETWORK-IN-4065V1.0
APPENDIX A – CONNECTIONS
This card has its outputs on a 4 points plug and a BNC connector. The RS422 AFNOR code
is available on the 4 points output :
Tx/Rx + Tx/Rx -
ENGLISH
1 2 3 4
Tx
GND
MDE-LEDI-NETWORK-IN-4065V1.0 95
4. RS232 and 485/422 ASCII+TOP (‘A’ and ‘R’ type)
The ASCII+TOP card has a 4 points plug and a DB9 connector. The 4 points plug is used
to output the TOP through static relays and the DB9 plug is used to output time frame using
RS-232 levels.
TXD
RS-232 line
driver RS-232 output
TX+
RS-485 line RS-485 output
driver TX-
The ASCII DB9 connector is localized on the backside of the rack and is shown below.
Connector pin-out for RS232 : Connector pin-out for RS485 and RS422 :
GND TXD GND TX+
5 4 3 2 1 5 4 3 2 1
9 8 7 6 9 8 7 6
TX-
The pulse (TOP) output is described below.
96 MDE-LEDI-NETWORK-IN-4065V1.0
APPENDIX A – CONNECTIONS
5.1. Pin-out
The 4 points plug on the ASCII and ALARM cards can provide a configurable time TOP
or synchro/power alarm TOP.
ENGLISH
The 4 points plug has the following pin-out:
1 2 3 4
MDE-LEDI-NETWORK-IN-4065V1.0 97
Here are some examples of how to use this output :
5.2. Examples of how to use the open collector output (pins 3-4)
General case :
loudspeaker
3 R +
External
WaRNING :
VDC max = 45 Volts
DC
4 -
Power
►► You need to add R if the load (LED, loudspeaker,…) does not accept the VDC
voltage.
►► To avoid the transistor destruction, limit the input current to 30 mA (i = Vdc / R <
30mA).
VDC
If VDC = 5 Volts :
R
3
5
Rmin = = 167Ω
4 0.03
98 MDE-LEDI-NETWORK-IN-4065V1.0
APPENDIX A – CONNECTIONS
5.3. Example of how to use the static relay output (pins 1-2)
loudspeaker
VCC R
1 +
External
WaRNING :
V max = 60 Volts
DC or AC
-
pulse 2
Power
Supply
ENGLISH
V
WARNING : You must ensure that i= < 130mA
R
MDE-LEDI-NETWORK-IN-4065V1.0 99
APPENDIX B – OUTPUT CODE FORMAT
This appendix contains a description of the time code used for the different kind of
outputs.
STX D A Y D D / M M / Y Y H H : M M : S S CR
100 MDE-LEDI-NETWORK-IN-4065V1.0
APPENDIX B – OUTPUT CODE FORMAT
ENGLISH
MDE-LEDI-NETWORK-IN-4065V1.0 101
2.2. Bit encoding
The signal is modulated only on ‘B’ card. The ‘T’ card output signal has TTL level.
102 MDE-LEDI-NETWORK-IN-4065V1.0
APPENDIX B – OUTPUT CODE FORMAT
P3 M
year 40 80
20 control bits
10
8 0
4
2
1
ENGLISH
10
month 8 50 10
4
2 J+1 =JF
1 JF
4 ES
day of week
2 E/H
(1= monday ; 7= sunday)
1 HE
20 40 20 HH
10 "0"
8 "1"
4 1
2 2
day of month 30 4
1 P2
8
20 10
10 8
4 2 1 P1 40 20 minutes
hours
KEY:
J Current day
JF State holiday
ES Standby transmitter used
E/H Indicates a seasonal changeover
on the next hour
HE Summer time
HH Winter time
P1, P2, P3 Parity bits
MDE-LEDI-NETWORK-IN-4065V1.0 103
APPENDIX C – TROUBLESHOOTING
This section tries to answer to most frequent question concerning the use of your NTP
device. First, ensure that the GTNetManager software and a SUN JAVA Virtual Machine
1.4.2_X are installed on your computer.
►► 1. Verify the cable connection. If Ethernet LEDs are visible, the upper-left LED
should be green. Otherwise, there should be a network connection or power supply
failure.
►► 2. If you use several VLAN (Virtual Local Area Network), verify that the device is on
the same VLAN than your computer.
►► 3. Connect your computer directly to the device using a straight cable. In DHCP
mode, the device take automatically an address in the range 169.254.x.y if it does
not find any DHCP server. Change your computer IP address in this range, with a
network mask of 255.255.0.0.
YES
Your computer and the device should have the same IP range and the same network
mask.
NO
See previous question.
Start Menu ► Settings ► ControlPanel ►Java Plug-in ► Advanced - select JRE 1.4.2_
Start Menu ► Settings ► ControlPanel ► Java Plug-in ► Cache - Uncheck “Enable Caching"
►► 3. Has the page been found by the browser (the loading begins but fails after a
while) ?
►► 1. Press ‘F5’ to refresh the WEB page, and go back to output panel. If the output is
ENGLISH
still missing, see next point.
Proceed to a “Factory Default”, then “Quit and save”. Refresh the WEB page.
►► 3. If the output is still missing, open the device. Check the black cables connections
and the switchs configurations (see Appendix D – MAINTENANCE / Output card
switchs verification).
►► 1. The device stays in this mode when it cannot reach any NTP server. Check that
the NTP servers are reachable on the network.
►► 2. Open the NTP panel of the configuration WEB page and verify that the IP addres-
ses of the NTP servers are correct. If in “auto-detect” mode, restart your device :
the auto-detection is done at start-up.
MDE-LEDI-NETWORK-IN-4065V1.0 105
APPENDIX D – MAINTENANCE
Battery checking
►► Open the product with the screw driver, the battery is located between the power
supply card and the display card
Synch. input
Power
Output N
Output 2
Output 1
…
Supply Battery
Display
►► Check the voltage, if the voltage is less than 7V, the battery is on failure.
106 MDE-LEDI-NETWORK-IN-4065V1.0
2. Output card switchs verification
If you need to add an output card or if an output seems to be in failure (do not appear in the
WEB page), open the device and verify the switch configuration on the output cards:
Output 1 Output 4
(the nearest of (the furthest of
Output 2 Output 3
the supply card the supply card
103064) 103064)
ENGLISH
1 output
1 2 3 4 5 6 7 8
2 outputs
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
3 outputs
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
4 outputs
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
The 8th switch of each card allows you to test the card by forcing the signal on output.
Don’t forget to put it OFF again after testing!
3. Updating Firmware
The upgrade is an auto-extractable executable. The name of this tool has the following
layout:
product_upgrade_prevers_new_vers_.exe
For example, for an update of the LEDI Network from any version 2 to the version 2.11,
the update file shall have the name ledinetwork_upgrade_2xx_211.exe.
MDE-LEDI-NETWORK-IN-4065V1.0 107
3.2. Reloading Firmware
Download the update executable and run it from your computer or execute it directly
from the WEB site. The following window appears at the screen :
►► Click on the Start button to extract all the files needed for the update. When the
extraction is terminated, the tool GTNetMng is automatically started.
☛☛When all the files have been extracted correctly, the tool start
automatically.
108 MDE-LEDI-NETWORK-IN-4065V1.0
APPENDIX D – MAINTENANCE
More information
about the update
ENGLISH
Click on this
button to see a
complete
description of the
update
To really start the update, enter the IP address of the product in the field IP address and
click on the UPDATE ! button. The update process start immediately.
When a problem occurs, an error message is displayed. Check the following points:
►► The product to update must be accessible through your network from the PC used
to run GTUpdate
►► check that the IP address is valid, compatible with those of your PC and that it’s
really the address of a Gorgy Timing product
MDE-LEDI-NETWORK-IN-4065V1.0 109
APPENDIX E – DATA
1. Measurements
424 mm
1U = 44 mm
263 mm 482 mm
2. Specifications
3. Autres spécifications
110 MDE-LEDI-NETWORK-IN-4065V1.0
3. Stamp contents
The stamp that identifies the product is localized on the top or on the backside of the pro-
duct. It contains the following information:
GORGY TIMING
CODE 9257/Xopt
ENGLISH
N° SERIE nnnnnn
The third line contains the serial number on 6 digits (nnnnnn). The second line contains a
description of the product:
ITEM CODE
9257 /
POWER SUPPLY
230VAC/50-60Hz 0
115VAC/50-60Hz 1
18-72 VDC 9
For example, the 9257/9AB code identify a LEDI Network IN with 18/72V Direct Current
power supply and two outputs. The first output uses the ASCII protocol, the second one
uses the IRIG-B/AFNOR output.
MDE-LEDI-NETWORK-IN-4065V1.0 111
APPENDIX F – ADDITIONAL DOCUMENTS
This appendix contains some documents that can be useful to manage a set of GT products
in your installation. Each document is a table that you can freely copy and distribute:
►► Installation description: you can use this table to make a synthetic view of all your
installation.
►► Device configuration: you can use this table to record for each device what is the
standard configuration of outputs and display.
112 MDE-LEDI-NETWORK-IN-4065V1.0
Summarized installation view
Installation description
Installation date
ENGLISH
Device description Serial number Localization
MDE-LEDI-NETWORK-IN-4065V1.0 113
Devices configuration
Installation description
Installation date
114 MDE-LEDI-NETWORK-IN-4065V1.0
NOTES
ENGLISH
MDE-LEDI-NETWORK-IN-4065V1.0 115
5. stop clock option
TECHNICAL SUPPORT
+33 476 30 48 20
support@gorgy-timing.fr
RADIO TIMING®, LEDI®, LEDICA®, HANDI® are trademarks by GORGY TIMING.
Number of statement for training provider activity : 82 38 04877 38
Gorgy Timing RC74B38 - Any technical, aesthetic, color modifications can be made without notice.
116 MDE-LEDI-NETWORK-IN-4065V1.0