Académique Documents
Professionnel Documents
Culture Documents
Home
About
Map
Links
Guestbook
1.Refer to the exhibit. The configuration steps that are listed in the exhibit have been entered in switch
S1 via the console. Subsequent attempts to telnet to the switch are not successful. What is causing the
problem?
2.Refer to the exhibit. How is port Gi1/1 on SWT-A functioning in the spanning-tree topology?
3.Which parameter is a specific frequency at which a wireless access point will operate?
channel
4.What will be the effect of the command S1# copy system:running-config tftp://172.16.2.155/tokyo-
config?
The running configuration file on S1 will be saved via TFTP to a file named tokyo-config.
MAC address
6.Refer to the exhibit. A wireless infrastructure has been established in a company building as shown.
The design goal was to allow roaming between the three APs for handheld devices. However, the
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 2 de 17
devices lose connectivity when the users roam. How can this problem be fixed?
Reposition the APs so that each area of signal strength overlaps the neighbor by at least 10-15%.
7.Refer to the exhibit. The network administrator wants to configure Switch1 to allow SSH connections
and prohibit Telnet connections. How should the network administrator change the displayed
configuration to satisfy the requirement?
9.Refer to the exhibit. A new host needs to be connected to VLAN 3. Which IP address should be
assigned to this new host?
192.168.1.22 /28
192.168.1.31 /28
192.168.1.32 /28
192.168.1.52 /28
192.168.1.63 /28
10.In setting up a wireless infrastructure network, which device is used to associate a client computer to
the network?
an Ethernet switch
Layer 2 root elections should be optimized by adjusting BPDU timers to match network diameter.
Using lower bandwidth connections between switches will allow STP to have a larger network diameter.
Portfast can be used to increase the allowable switched network diameter because it disables the forward
delay and maximum age timers.
12.Refer to the exhibit. Hosts that are connected to switch SW1 are not able to communicate with Hosts
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 3 de 17
in the same VLAN that are connected to switch SW2. What should be done to fix the problem?
Configure both switches in VTP transparent mode to allow them to share VLAN information.
Reconfigure the fa0/1 interface on switch SW1 with a static trunk configuration.
Apply IP addresses that are in the same subnet to FastEthernet 0/1 on SW1 and FastEthernet 0/2 on
SW2.
13.Refer to the exhibit. What would happen if the network administrator moved the network cable of
Host A from interface Fa0/1 to Fa0/3 on switch SW1?
Host A remains a member of VLAN 10, because the router is routing traffic between VLANs.
Host A is no longer a member of VLAN 10, because port Fa0/3 has been manually assigned to
VLAN 30.
Host A remains a member of VLAN 10, because the switch provides dynamic VLAN assignment for the
port.
Host A maintains connectivity to all members of VLAN 10, because it is connected to the same physical
network.
Host A is no longer a member of VLAN 10, but because port Fa0/3 was unused, it is now a member of
VLAN 1.
14.Refer to the exhibit. All hosts are in listen mode. Host 1 and Host 4 both transmit data at the same
time. How do the hosts respond on the network? (Choose two.)
The hub will block the port connected to Host 4 to prevent a collision.
Hosts 1 and 4 are assigned shorter backoff values to provide them priority to access the media.
If a host has data to transmit after the backoff period of that host, the host checks to determine if
the line is idle before transmitting.
15.What are two requirements for configuring inter-VLAN routing using the router-on-a-stick model?
(Choose two.)
Each subinterface should be configured with its own IP address, subnet mask, and unique VLAN
assignment.
The physical interface of the router must be connected to a trunk link on the adjacent switch.
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 4 de 17
The number of physical interfaces on the router should match the number of VLANs.
16.Refer to the exhibit. Router R1 is properly configured for router on a stick inter-VLAN routing, but
PC1 is unable to ping PC2. What needs to be done to resolve the problem?
Rename VLAN1.
17.Refer to the exhibit. If switch SW1 is configured with the four VLANs as shown in the exhibit, how
many physical interfaces are needed on router R1 to configure inter-VLAN routing using subinterfaces?
zero
one
two
four
18.Refer to the exhibit. Router RA receives a packet with a source address of 192.168.1.35 and a
destination address of 192.168.1.85. What will the router do with this packet?
The router will forward the packet out interface FastEthernet 0/1.1.
The router will forward the packet out interface FastEthernet 0/1.2.
The router will forward the packet out interface FastEthernet 0/1.3.
The router will forward the packet out interface FastEthernet 0/1.2 and interface FastEthernet 0/1.3.
19.Refer to the exhibit. What does the term DYNAMIC indicate in the output that is shown?
This entry can only be removed from the MAC address table by a network administrator.
When forwarding a frame to the device with address 0060.5c5b.cd23, the switch does not have to
perform a lookup to determine the final destination port.
Only the device with MAC address 0060.5c5b.cd23 will be allowed to connect to port Fa0/18.
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 5 de 17
The switch learned this MAC address from the source address in a frame received on Fa0/18.
shared key
SSID
ad hoc
channel
21.Refer to the exhibit. Hosts B and C attempt to transmit a frame at the same time, but a collision
occurs. Which hosts will receive the collision jamming signal?
22.What is an efficient and cost effective way to minimize the frequency and effects of broadcast storms
on an Ethernet LAN?
Divide the computers into separate workgroups using different physical switches.
23.Refer to the exhibit. The switches in the exhibit have VTP pruning enabled. Which VLAN(s) will be
allowed on the trunk to SW2 by SW4?
VLAN 20 only
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 6 de 17
24.What is the correct order in which the STP components are chosen?
25.Refer to the exhibit. Hosts PC_A and PC_B send traffic simultaneously, and the frames from the
transmitting stations collide. What is the last device to receive the collision?
hub HB1
switch SW1
router R1
switch SW2
router R2
switch SW4
26.Refer to the exhibit. What three statements describe why Host1 and Host2 are unable to
communicate? (Choose three.)
The host default gateway addresses must be on the same logical network.
The switch with the highest priority will be assigned the lowest BID in the root election.
The first step in the spanning-tree election process is to determine the root port.
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 7 de 17
To select designated ports, the spanning-tree algorithm must determine the longest contiguous path from
the root bridge.
28.While configuring a new switch, a network administrator configures the switch as an HTTP server.
What benefits does this configuration provide?
This allows the switch to host web pages for the network.
This allows remote VPN connections to the switch over the Internet.
29
What are two benefits of the IEEE 802.11n standard over the IEEE 802.11G? (Choose two.)
30
Refer to the exhibit. The network administrator wants to allow both SSH and Telnet connections to
Switch1. However, the SSH connections fail. What is the most likely cause of this problem?
The domain name has been configured in the wrong configuration mode.
31
Refer to the exhibit. A new switch, SW3, has been added to the network. The network administrator
determines that VLAN information is not propagating to SW3. Which command will remedy the
problem?
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 8 de 17
32
Which CLI mode allows users to access all device commands, such as those used for configuration,
management, and troubleshooting?
33
Refer to the exhibit. Users A and B are reporting intermittent connectivity problems. Pre-installation
surveys showed strong signal strength from the AP locations to the client locations. Outside electrical
interference has been eliminated. What will fix the problem?
34
A switch that is using port-based memory buffering receives two incoming frames on the same port. The
destination port for the first frame that is received is busy. How will the switch handle the second frame
that it received?
The second frame will have to wait to be delivered even if its destination port is available.
The second frame will be delivered to the memory buffer for its destination port.
The second frame will be placed in a common memory buffer to await delivery.
35
Refer to the exhibit. The network administrator has just added VLAN 50 to Switch1 and Switch2. Hosts
A, B, C, and D are correctly configured with IP addresses in the subnet range for VLAN 50. Host A can
communicate with host B, but cannot communicate with host C or host D. What is the cause of this
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 9 de 17
problem?
VLAN 50 is not allowed on the trunk link between Switch1 and Switch2.
36
Refer to the exhibit. Switch SW2 was tested in a lab environment and then inserted into a production
network without reloading its configuration. After the trunk link between SW1 and SW2 was brought
up, all users lost connectivity to the network. What could be the source of the problem?
All the VLANs were pruned from the trunk port between SW1 and SW2.
SW1 and SW2 cannot be both set as VTP servers in the same VTP domain.
VTP configuration revision number of SW2 was higher than the configuration revision number of
SW1.
The additional VLANs from SW2 created more VLANs than the VLAN database of SW1 could contain.
37
Company policy requires disabling the command history buffer on network devices. An administrator
enters terminal no history size at the command prompt on a Cisco Catalyst switch and receives no error
messages back, but the command history buffer is still available. What is the problem?
The Cisco IOS version does not support disabling the command history buffer.
The size parameter reset the default buffer size but did not disable access to the buffer.
38
Refer to the exhibit. Which two options correctly describe the router configuration that is shown?
(Choose two.)
Routing between the 192.168.1.0 and 192.168.3.0 networks will not succeed until a routing protocol is
configured on the router.
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 10 de 17
39
Refer to the exhibit. After entering the commands in the exhibit, the administrator receives a “password
required, but none set” message when attempting to connect to S1. What is the problem?
lines.
The VLAN1 interface has not be enabled with the no shutdown command.
40
Refer to the exhibit. A network administrator has segmented the network into two VLANs and
configured R1 and S1 as displayed. However, PC1 is unable to access PC2. What is the likely problem?
Only one physical link between S1 and R1 is configured for inter-VLAN routing.
41
Refer to the exhibit. The Layer 2 switching design that is shown has been implemented in a campus
environment that is using Spanning Tree Protocol. All inter-switch links that are shown are trunks.
Whenever an inter-switch link fails, the network takes nearly a minute to completely converge. How can
the convergence time be reduced?
Increase the capacity of the distribution and core trunk links to 10 Gb/s.
42
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 11 de 17
Refer to the exhibit. What are two reasons for the Fa0/24 port being placed in the blocking state?
(Choose two.)
The Fa0/24 port is overloaded with too much traffic for its configured bandwidth.
43
Which three actions are performed during the boot sequence of a Cisco switch? (Choose three.)
The boot loader uses the self-contained switch operating system to boot the switch.
The boot loader initializes the flash file system that is used to boot the system.
The boot loader loads the default operating system if the flash-based operating system is corrupt or
missing.
44
Which combination is required to establish a connection to initially configure the Linksys WRT300N
wireless access device?
a computer configured in the same IP subnet as the WRT300N and a direct cable connection to it
45
Refer to the exhibit. RTB is configured for traditional inter-VLAN routing. RTB can ping computer A
but cannot ping computer B. What is a possible cause of this failure?
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 12 de 17
Router interface Fa0/1 has the wrong trunk encapsulation type configured.
46
In which mode is a VTP switch operating if it has been configured to only forward VTP advertisements?
client
root
server
transparent
47
Refer to the exhibit. Switch SW2 has been newly purchased and added to the network. What
configuration should be applied to SW2 so that it participates in the same VTP domain as switch SW1,
receives VLAN information from SW1, and synchronizes VLAN information?
48
Refer to the exhibit. What is the effect of setting the security mode to WEP on the Linksys integrated
router?
WEP encrypts data between the wireless client and the access point.
WEP ensures that only authenticated users are allowed access to the WLAN.
WEP translates an internal address or group of addresses into an outside, public address.
49
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 13 de 17
Refer to the exhibit. What will allow a host on VLAN 40 on switch X to communicate with a host in
VLAN 40 on switch Y?
QoS
routing
trunking
VPN
50
Refer to the exhibit. All switches are configured with the default bridge priority. Which port will act as a
non-designated port if all links are operating at the same bandwidth?
51
DSSS
OFDM
SSID
WPA
52
Refer to the exhibit. Computer D sends a broadcast message. Which devices will process the broadcast
message?
computer E
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 14 de 17
90% correct
[Traductor]
CCNA, CCNA3
彩虹天堂-Rainbow Heaven
3 comments
Add comment
学习了!看来你真的要准备考CCNA啊!呵呵,支持!
哎….我这个专业必考…学的头大
Router R1 is properly configured for router on a stick inter-VLAN routing, but PC1 is unable to
ping PC2. What needs to be done to resolve the problem?
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 15 de 17
Leave A Reply
Name
Website
Post Comment
Categories
CCNA
IT相關
WORDPRESS
個人日記
學習相關
未分類
照片圖片
雜談
電影分享
音樂分享
Archives
November 2010
June 2010
May 2010
April 2010
March 2010
February 2010
January 2010
December 2009
November 2009
October 2009
September 2009
August 2009
July 2009
June 2009
May 2009
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 16 de 17
March 2009
Meta
Log in
Search
Recent Posts
我回来了。。
六月
悲劇的時代
Ubuntu之離線寫BLOG軟體-Lekhonee
解決WUBI安裝Ubuntu 9.10更新後出現無法進入系統的問題
給HTC HERO使用好看的蘋果字體
近況
手機大集合
其實,我已經回到了墻內
Keep ALL SIMPLE
Recent Comments
博客之家
你终于回来了,实在太...
尹雷
华丽的飘过!
大学生创业
不错哦.要经常宫鑫....
意美
的确没有更新啊
广州seo
博主可以交换个友情链...
Older »
Tag Cloud
仙劍奇俠傳 哈利波特 照片圖片 視頻 電影分享 音樂分享 apple avatar Camera CCNA CCNA1 CCNA2
CCNA3 CCNA4 CNZZ creative dv2 flash GFW Google htc I&E Jdrama jquery laptop lekhonee love monkey majik mysql Network
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010
CCNA 3 – Final Exam (B) latest | Never summer, Ever summer Página 17 de 17
operating system Personal PHP5 seo singapore theme ubuntu vista VPN Windows WORDPRESS wpg YUI
Top
http://neversummer.net/ccna3-final-exam-b-latest/ 25/11/2010