Académique Documents
Professionnel Documents
Culture Documents
MANUAL
F21-4D/S
Industrial Radio Remote Controller
Serial number :
Channel :
Importer:
PODEMCRANE AD
1 Gen. Nikolov Str
5300 Gabrovo
BULGARIA
Ver.1.2
Table of Contents
Operator’s Manual
Chapter 1 Warranty
Chapter 2 Precautions of Operation
Chapter 3 Standard Delivery
Chapter 4 Operation
Chapter 5 Installation and function settings
Chapter 6 Inspection and maintenance
Chapter 7 General features
APPENDIX
CE – declaration
Channel / frequency reference table
2 Version 1.2
Part 1. Operator’s Manual
Chapter 1 Warranty
1-1 Warranty
Lee’s Hi-Tech Enterprises Co., Ltd. guarantees that this product meets its
published specifications at the time of shipment from the factory. The product
is supplied with CE-declaration. (see appendix)
1-4 Remarks
• No other warranty is expressed or implied, except for the above mentioned.
• The remedies provided herein are the buyer’s sole and exclusive remedies.
TELECRANE or the importer shall not be liable for any direct, indirect,
special, incidental or consequential damages.
3 Version 1.0
Chapter 2 Precautions of Operation
2-1 General
• Please carefully read the manual before installing and operating this device.
• Never let the equipment be dismantled by an unauthorized individual whom
has not been appointed by the importer or manufacturer, equipment may be
damaged and warranty will no longer be applicable.
• This manual is for reference only. Please consult your distributor for further
assistance.
• The equipment has been strictly tested for quality before delivery from Lee’s
Hi-tech Enterprise Co. However, this equipment must not be used in dangerous
situations or where damage may result.
• After finishing operation of the TELECRANE radio remote shut off the main
power to the installation, power to receiver, and remove transmitter key (when
applicable).
• Transmitter should be placed in a safe and clean area when not in use to avoid
accidental pressing of buttons.
• The installation should be equipped with all necessary safety features e.g. main
power relay, limit switch and other safety devices.
• Don’t use equipment during lightening or high electrical interference
conditions.
• Make sure that the batteries are in good condition and that the power supply for
the receiver is the right one.
• Installation and maintenance should only be done while the installation’s main
power has been switched off to prevent electrical shock.
• The contents of this manual may be amended by the importer / manufacturer
without notice.
• The manufacturer may introduce new functions to the equipment as necessary,
therefore, the descriptions may change.
• The patent and related documents for the equipment belong to LEE’S HI-
TECH CO., LTD. and they aren’t allowed to be used by others without
permission.
• F21 series systems makes use of many patents belonging to LEE’S HI-TECH
CO., LTD. and its associated companies.
4 Version 1.0
2-2 Precautions
The F21 system has various protections to guard against different emergencies
including strict security code checking and automatic monitoring of part failure.
The F21 system has an isolation circuitry that protects it from outside voltage
surges and interference. In the event of sensing an emergency situation the F21
will perform an emergency stop of the equipment. It is important to properly
install the F21 system so it can perform the emergency shutdown properly.
5 Version 1.0
Chapter 3 Standard delivery
(1) 1 Transmitter
(2) 1 Receiver.
1 sets of non-rechargeable (total 2) AA batteries
(3) Operation manual with CE-declaration
6 Version 1.0
Chapter 4 Operation
EMS
Key switch
Push buttons
LED indicator
Battery cap
7 Version 1.0
4-2 F21-4D/S Receiver’s parts
Antenna
Receiver / Decoder
module
(Internal)
LED indicators
(Internal)
Relay module
(Internal)
Transformer
(Internal)
8 Version 1.0
4– 3 General operation
Remark: When the batteries of the transmitter are almost empty the LED
indictor will turn red instead of green. If the batteries are as good as
empty the transmitter will sent EMS signal to the receiver to be
switched off. Try to avoid the therefore mentioned situation and
replace the batteries when the LED indicator turns red.
Power-on:
Turn the rotary key clockwise from “OFF” to
“ON” and consequently to “start” position.
The transmitter is now ready for use
Hoisting:
Press pushbutton “UP” to activate the hoisting
motion. Pressing to the second stage of the
pushbutton will result in activating the high speed
(if available).
Trolley movement:
Press pushbutton “EAST / WEST” to activate
trolley travelling into the required direction.
Pressing to the second stage of the pushbutton will
result in activating the high speed (if available).
EMS:
9 Version 1.0
By pressing the EMS button the main relay will de-energize. The radio remote can
be switched on again by pressing one of the function buttons.
LED-Indicator:
De LED-Indicator shows the status of the batteries. (When the transmitter has been
switched on) LED indicator colors:
4– 5 Extra functions
10 Version 1.0
Chapter 5 Installation and Function Setting
Receiver
As far as possible
Motor M Frequency
Converter
Cable
9. The receiver should be installed on the outside of the electrical control box.
To mount the receiver inside the electrical control box is not correct.
Receiver
Antenna
Cable
⌧ Cable
☺
(Incorrect) (Correct)
Receiver
Electrical (Electrical
control box) control box)
11
Version 1.0
5-2 Transmitter installation instructions
12 Version 1.0
1. Selecting the right power supply
48 V
220 V
Jumper
Pins
(Connectors)
48V 220V
Wire Description
Wire Description
Remark:
-Check if all wires are properly connected
14 Version 1.0
4. Secure the cables between the receiver and the installation so that the cable
cover (wrapper) will not wear out due to vibrations of the installation.
5. Switch on the main power to the installation.
6. Operate the transmitter to test every function and make sure they are all
correct (you are able to check this by making use of the LED indicators
that are located inside the receiver).
7. This completes the installation of receiver.
15 Version 1.0
Chapter 6 Inspection and maintenance
6– 1 Inspection
Daily inspection is important and will ensure the safety of operation. Inspection
should include “emergency stop” and other safety devices and functions. If
there is any doubt, operation must be stopped immediately and problems must
be solved before resuming operation.
6– 2 Maintenance
16 Version 1.0
Chapter 7 General features
17 Version 1.0
EG –DECLARATION OF COMFORMITY
According to EG-Directive for Machinery 89/336/EEC
93/68/EEC EG-EMV-Guidelines
99/5 EEC Radio Telecommunications equipment
19 Version 1.0