Académique Documents
Professionnel Documents
Culture Documents
Fixed Base Plate - 03SF02
Fixed Base Plate - 03SF02
E
E
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Design of Fixed Base Plate BP9 for 03SF02 As per IS 800-2007
1. Geometry :-
Dimensions of Base Plate :-
Length of base plate in direction parllel to web (Dp)
Width of base plate in direction parallel to flange (B p)
=
=
500
350
mm
mm
Orientation of column =
E
Thickness of base plate = 20 mm < 30 mm OK
Grout pocket
ISMB 200
M16 Bolts
Note :- Base plate connection is designed as Fixed support,Bolts are designed only for the tensile forces and all
shear is carried by the shear lug embedded below base plate.
Page 48 of 62
2. Anchor bolt details :-
Diameter of anchor bolt db = 16 mm
Gross area of Bolt = Asb = 201 mm2
Net area of Bolt = An = 157 mm2
Ultimate Stress of Anchor bolt = fub = 470 N/mm2 ( Refer LS - 503 -01)
Yield Stress of Anchor bolt = fyb = 345 N/mm 2
( Refer LS - 503 -01)
Partial Safety factor for Material g mo = 1.1 ( Refer Table-5,IS 800-2007)
Partial Safety factor for Material gmb = 1.25 ( Refer Table-5,IS 800-2007)
Nominal tension capacity of bolt = Tnb
Tnb = min ((0.9 fub x An), (fyb xAsb x (gmb/gmo)) = Tnb = 66 kN ( Cl. 10.3.5, IS 800-2007)
Allowable Tensile stress in bolt =Tdb = Tnb/gmb = Tdb = 53 kN ( Cl. 10.3.5, IS 800-2007)
Limiting tensile force on bolt as per LS = TLS = TLS = 46 kN ( Refer LS - 503 -01)
Capacity of Bolt in axial tension = Td = Min of Tdb & TLS = Td = 46 kN
c/c distance betn bolts (In Web Dir.) bp = 350 mm >= 140 mm OK
c/c distance betn bolts (In Flange Dir.) dp = 200 mm >= 140 mm OK
Number of anchor bolts provided 4
Edge Dist. From Base Plate along Z axis (In Web Dir.) dm = 75 mm >= 55 mm OK
Edge Dist. From Pocket (In Web Direction) 87.5 mm >= 50 mm OK
Edge Dist.From Base Plate along X axis (In Flange Dir.) dn = 75 mm >= 55 mm OK
Edge Dist. From Pocket (In Flange Direction) 25 mm < 50 mm OK
Page 49 of 62
4. Design of Anchor bolts
Tensile force in per Anchor Bolt = T ' / Total no. of bolts in base plate= T = 0.00 kN
Tensile force in per Anchor Bolt = TXX' / nos. of Bolts along X axis on one side of section = TXX = 17.83 kN
Tensile force in per Anchor Bolt = TZZ' / nos. of Bolts along Z axis on one side of section = TZZ = 0.00 kN
Page 50 of 62
5. Design of Base Plate
Page 51 of 62
Thickness of base plate due to Mxx
Z
Thickness of plate for Tension
12
Tension per bolt (Tbx) = Tbx = 17.82769 kN b 169
PART-I Plate fixed in two adjacent edges and free on other edges. 350
Minimum Pressure at the edge of the Plate = Pmin = -1.25 N/mm2 138
Page 52 of 62
Thickness of base plate due to MZZ
12
Tension per bolt (Tbz) = Tbz = 0.00 kN
b 169
Moment = TbZ x (b-dn) Mz = 0 N.mm
138
Thickness of base plate required treq = 0.00 mm
X 500 200
PART-I Plate fixed in two adjacent edges and free on other edges. 350
Maximum Pressure at the edge of the Plate = Pmax = 0.12 N/mm2 138
Minimum Pressure at the edge of the Plate = Pmin = 0.12 N/mm 2
Page 53 of 62
DESIGN OF STIFFNER PLATE
CHECK : (1) Depth /Thickness ratio < 29.3 ɛ = h1/t = bf/t = 11.50 OK
(2) Permissible outstand of plate = 13.6 x ɛ x t = 137.0 mm
Actual Outstand of plate =Average height of plate = 125 mm OK
CHECK : (1) Depth /Thickness ratio < 29.3 ɛ = h1/t = bf/t 10.42 OK
(2) Permissible outstand of plate = 13.6 x ɛ x t = 137.0 mm
Geometry :-
Dimensions of Base Plate :-
Length of base plate in direction of web = 500 mm
Width of base plate in direction of flange = 350 mm
Thickness of base plate = 20 mm
###
X h
100
Shear Capacity (Vp) = Av x fyw /SQRT(3) / gmo = Av x (250/sqrt(3)) /1.1 (Clause 8.4.1,IS 800-2007)
12.4
Stress ratio for shear lug = = 0.088 < 1.000 Section is safe in shear.
140.7
Page 55 of 62
Check for shear stress in lug (Parallel to Flange) :
Resisting area of section for shear (parallel to lug web) Aw = 75 x 8 x 2 = 1200 mm2
As per Clause 8.4,IS 800-2007
Aw =A x b /( b+h) = ((75^2)-(75-8-8)^2)x(75-8-8))/(8-8-8)+(75-8-8) = 1072 mm2
Av =Minimum of Above two = 1072 mm2
Shear Capacity (Vp) = Av x fyw /SQRT(3) / gmo = Av x (250/sqrt(3)) /1.1 (Clause 8.4.1,IS 800-2007)
3.9
Stress ratio for shear lug = = 0.028 < 1.000 Section is safe in shear.
140.7
50
50
100
Moment in shear lug @ major axis Mx = 12.4 x( 50.00 + 50.0 )= 1239 kN.mm
Moment in shear lug @ minor axis Mz = 3.9 x( 50.00 + 50.0 )= 389 kN.mm
Pocket Size Required For shear lug :- 175 x 175 x 150 Deep
Page 56 of 62
7 Design of Weld :
7.2 Design of welded connection for Stiffners plates with Column section
Permissible stress of weld material =fwd = (fu/√3) /gmw fwd = 189.4 N/mm2
Strength of weld per mm = Sw = 0.707 x fwd x S Sw = 1071.1 N/mm
Permissible stress of weld material =fwd = (fu/√3) /gmw fwd = 189.4 N/mm2
Strength of weld per mm = Sw = 0.707 x fwd x S Sw = 1071.1 N/mm
Page 57 of 62
7.3 Weld connection between Stiffner plate and Base plate
7.4.1 Design of Weld between Base plate and Shear Lug along X Axis X
Total Length available for welding along X axis = Lwxgross = 150 mm
Deduction for End return of the weld as shown in figure= 4 x Size of weld = 32 mm
Net Length available for welding along X axis = Lwxnet = 118 mm
Length of Weld requied along X axis = Fx/ Sw = (3.888/1) = 4 mm
Weld Size is adequate.
7.4.2 Design of Weld between Base plate and Shear Lug along Z Axis
Total Length available for welding along Z axis = Lwzgross = 150 mm
Deduction for End return of the weld as shown in figure= 4 x Size of weld = 32 mm
Net Length available for welding along Z axis = Lwznet = 118 mm
Length of Weld requied along Z axis = Fz/ Sw = (12.387/1) = 12 mm
Weld Size is adequate.
Page 58 of 62
Case 1 For Uniform decreasing Pressure over entire surface :--
2/3 b
a
Page 59 of 62
Case 3 For Uniform decreasing Pressure over 1/3 rd surface :--
1/3 b
Page 60 of 62
Case 5 For Uniform decreasing Pressure over entire surface :--
a
For Uniform decreasing Pressure over entire surface :--
B1
Case 0.125 0.25 0.375 0.5 0.75 1 a
Case 1 F 0.043 0.133 0.212 0.328 0.537 0.695
Case 2 F 0.04 0.109 0.154 0.215 0.304 0.362
Case 3 F 0.025 0.052 0.071 0.084 0.1 0.109
Case 4 0.05 0.182 0.353 0.631 1.246 1.769
Case 5 F 0.007 0.049 0.141 0.303 0.709 1.074
B2 b
Case 0.125 0.25 0.375 0.5 0.75 1
Case 1 F 0.028 0.09 0.148 0.2 0.276 0.397
Case 2 F 0.026 0.059 0.089 0.107 0.116 0.113
Case 3 F 0.014 0.028 0.031 0.029 0.025 0.02
Case 4 0.047 0.188 0.398 0.632 1.186 1.769
Case 5 F 0.019 0.098 0.25 0.432 0.91 1.372
B1
Case 0.25 0.5 0.75 1 1.5 2 3
Case 1 F 0.018 0.064 0.12 0.195 0.351 0.507 0.758
Case 2 F 0.017 0.056 0.095 0.141 0.215 0.277 0.365
Case 3 F 0.014 0.035 0.047 0.061 0.076 0.086 0.1
Case 4 0.25 0.5 0.75 1 1.5 2 3
Case 5 F 0.002 0.017 0.053 0.126 0.376 0.719 1.347
B2
Case 0.25 0.5 0.75 1 1.5 2 3
Case 1 F 0 0 0 0 0 0 0
Case 2 F 0.019 0.05 0.068 0.099 0.114 0.113 0.101
Case 3 F 0.01 0.024 0.031 0.03 0.025 0.02 0.014 b
Case 4 0.016 0.066 0.148 0.259 0.484 0.605 0.519
Case 5 F 0.016 0.066 0.148 0.259 0.484 0.605 0.519
a
B3
Case 0.25 0.5 0.75 1 1.5 2 3
Case 1 F 0.019 0.068 0.125 0.166 0.244 0.387 0.514
Case 2 F 0 0 0 0 0 0 0
Case 3 F 0 0 0 0 0 0 0
Page 61 of 62
Case 4 0.031 0.126 0.236 0.511 1.073 1.568 1.982
Case 5 F 0.012 0.058 0.111 0.345 0.829 1.181 1.468
Page 62 of 62