Académique Documents
Professionnel Documents
Culture Documents
Part #1335-0102-04
Quantity Description Part No.
1 Classic Mesh Grille Complete - Upper ************
Includes: XLR Classic Grille Frame 1335-0141-04
XLR Classic Mesh Insert 1335-0020-04
XLR Classic Hood Moulding 1335-0050-04
XLR Classic Upper Mounting Plate 1335-0206-04
(2) XLR Mesh Retainers 1335-0029-04
1 LowerMesh Grille Frame 1335-0023-04
1 Lower Mesh Grille Section 1335-0021-04
1 Hardware Kit (components listed below) 1335-1902-04
1 XLR Emblem Mounting Plate 1335-0035-00
5 #8-32 ESNA Half Nuts 1999-0065-00
5 Black Plastic Washers 1999-0256-00 1. Remove the radiator support cover by removing the fac- 2 3
2 #8-32 S.S. Hex Nuts 1999-9072-00 tory push pins and remove the cover (to be reinstalled).
2 #10 S.S. Lock Washers 1999-9555-00 Use masking tape to prevent marking the cover with the
1’ .030” x 1” Double Faced Tape 3004-9240-92 tool.
2 1.006” x .189” x .062” Black Washers 1999-0264-00
WARRANTY INFORMATION:
E&G Classics, Inc. warrants its chrome parts and products to be free from defects in 2. Carefully apply several layers of masking tape around the
material, workmanship or finish for Forty-Eight (48) months from the date of shipment
by E&G. This warranty is limited to the repair or replacement, at E&G Classics option, 4 painted grille surround to protect the factory paint.
of the defective part or product. 3. Remove the top torx T-30 fasteners retaining the grille.
To obtain performance under this warranty you must:
1.) Present your E&G unit to an authorized distributor in your area with proof
of purchase.
2.) If no distributor is available, contact E&G Classics (address below) for authori-
zation to return unit.
3.) Returns - All unauthorized returns will be refused. Merchandise approved by E&G
for return must have been purchased within the Forty-Eight (48) months. All returns
require an authorization number obtained from E&G and the actual return must be
accompanied by the written authorization form filled out completely. All merchan-
dise must be inspected upon receipt and shortages reported within 48 hours. All
merchandise must be in a resalable condition. Merchandise must be packed careful
ly in the original packing. If original packing is no longer usable, repack item(s) com
parable to original manner. All returns are subject to a 25% handling charge. Special
order items are not returnable. Defective merchandise must have an explanation of
the problem. No credit will be issued unless invoice number and date of purchase
has been supplied. Manufacturer shall be sole judge of defects in a product.
4.) UPS accounts - All returns must be prepaid. Do not send return shipments freight
collect. Once E&G has made its decision and it is a claim against our warranty pol-
icy, E&G will credit incoming freight on damaged parts.
5.) No discontinued part or parts changed due to body style are returnable.
For Return Authorization, write or telephone: E&G Classics, Inc., 8910 McGaw 4. Use a plastic tucking tool (to make sure you do not dam-
Court, Columbia, MD 21045 (410) 381-4900 Attn.: Return Department. age the paint) to seperate the bumper cover plastic from
You are responsible for inspecting all packages containing E&G Classics' parts and product imme- the grille lower mounting studs and pull straight out on
diately upon their receipt and must file a claim with the carrier for any damage disclosure by such in- the bottom of the grille to unclip the bottom studs.
spection and notify E&G classics in writing at the above address of any such damage. This warranty
does not extend to any of our products which have been subject to misuse, neglect, accident or have IMPORTANT! The lower studs are under tension and
been altered or repaired in any way. This warranty does not cover any accidental or consequential require maximum effort on your part to release as the 5. For XLR’s painted any other color than black: Use masking
damages for any breach of this warranty agreement. E&G Classics shall have no responsibility for any tape to tape around the grille return as shown. Apply flat
loss of time, inconvenience, commercial loss or consequential damage, nor shall E&G be liable for any mounting hole is slightly smaller than the stud that snaps
injury or damage to persons or property by reason of any defect in material, workmanship or finish into it. Carefully unclip one stud at a time, working your or semigloss black paint to everything inside the grille
of its parts or products. This warranty gives you specific legal rights and you may also have other opening and the edge of the grille opening return.
rights which may vary from state to state. way from one side to the other. Do not start in the center.
Car Accessories | Cadillac Accessories | Cadillac Grilles
8
6 6
7
7
6. Remove the factory wreath & crest emblems from the 7. Fasten the emblem mounting plate to the center of the 9. Use a 3/16” drill bit to enlarge the outer two (2) mounting
Cadillac grille. The wreath is taped on, while the crest E&G Grille using the 1.006” x .189” x .062” black plastic holes where the outer studs on the E&G grille will pass
unclips. Remove the crest from the base. Apply new dou- washers, #10 lock washers and #8-32 S.S. hex nuts. Do through (slot the holes longer to the inside). Use the
ble faced tape to the back of the wreath (not shown) not use ESNA nuts. 3/16” drill bit to clean up the remaining mounting slots by
and crest (as shown) and attach it to the E&G mounting 8. Apply silicone to the back of the crest emblem to perma- laying the drill down at the angel show (use extreme care
not to damage the paint).
plate. nently secure the emblem to the mesh insert
12
13
11
10. Carefully align the E&G grille into the grille opening, 11. Make sure the bumper cover is tight against the mesh 12. Reinstall the factory torx T-30 screws with the supplied
making sure the two outer and center studs and the and grille frame once the ESNA nuts are tightened. 1” O.D. x 3/16” I.D. black plastic washers.
lower alignment tabs across the bottom of the grille fit 13. Make sure that the surface of the grille frame is protrud-
into the factory mounting holes. Lean the grille out at ing past the surface of the bumper cover approximately
the top for access and install a small black plastic washer 1/16”.
onto each stud and install an 8-32 ESNA half nut and,
once the grille is centered, completely tighten.
21
21