0 évaluation0% ont trouvé ce document utile (0 vote)
46 vues3 pages
A router connected to the switch is needed to forward traffic between the hosts. A router is configured to connect to a trunked uplink as shown in the exhibit. The information contained in a BPDU is used to determine the shortest path to the root bridge to determine which ports will forward frames as part of the spanning tree.
A router connected to the switch is needed to forward traffic between the hosts. A router is configured to connect to a trunked uplink as shown in the exhibit. The information contained in a BPDU is used to determine the shortest path to the root bridge to determine which ports will forward frames as part of the spanning tree.
Droits d'auteur :
Attribution Non-Commercial (BY-NC)
Formats disponibles
Téléchargez comme TXT, PDF, TXT ou lisez en ligne sur Scribd
A router connected to the switch is needed to forward traffic between the hosts. A router is configured to connect to a trunked uplink as shown in the exhibit. The information contained in a BPDU is used to determine the shortest path to the root bridge to determine which ports will forward frames as part of the spanning tree.
Droits d'auteur :
Attribution Non-Commercial (BY-NC)
Formats disponibles
Téléchargez comme TXT, PDF, TXT ou lisez en ligne sur Scribd
What two statements can be concluded from the information
that is shown in the exhibit? (Choose two.) All ports that are listed in the exhibit are access ports. A router connected to the switch is needed to forward traffic between the hosts. A router is configured to connect to a trunked uplink as shown in the exhibit. A packet is received on the FastEthernet 0/1 physical interface from VLAN 10. The packet destination address is 192.168.1.120. What will the router do with this packet? The router will forward the packet out interface FastEthernet 0/1.2 tagged for V LAN 60. 3. The information contained in a BPDU is used for which two purposes? (Choose t wo.) to determine the shortest path to the root bridge to determine which ports will forward frames as part of the spanning tree 4. A router has two serial interfaces and two Fast Ethernet interfaces. This rou ter must be connected to a WAN link and to a switch that supports four VLANs. Ho w can this be accomplished in the most efficient and cost-effective manner to su pport inter-VLAN routing between the four VLANs? Connect a trunked uplink from the switch to one Fast Ethernet interface on the r outer and create logical subinterfaces for each VLAN. 5. When are MAC addresses removed from the CAM table? after they have been idle for a certain period of time Refer to the exhibit. Switch1 is not participating in the VTP management process with the other switches. Which two are possible reasons for this? (Choose two.) Switch1 is using VTP version 1 and Switch2 is using VTP version 2. Switch1 is in a different management domain. 7. Which three must be used when a router interface is configured for VLAN trunk ing? (Choose three.) one subinterface per VLAN one IP network or subnetwork for each subinterface a compatible trunking protocol encapsulation for each subinterface Refer to the exhibit. The switches are connected with trunks within the same VTP management domain. Each switch is labeled with its VTP mode. A new VLAN is adde d to Switch3. This VLAN does not show up on the other switches. What is the reas on for this? VLANs created on transparent mode switches are not included in VTP advertisement s. 9. Which two criteria are used by STP to select a root bridge? (Choose two.) bridge priority base MAC address 10. Which three steps should be taken before moving a Catalyst switch to a new V TP management domain? (Choose three.) Reboot the switch. Reset the VTP counters to allow the switch to synchronize with the other switche s in the domain. Select the correct VTP mode and version. Configure the switch with the name of the new management domain. 11. Which two items will prevent broadcasts from being sent throughout the netwo rk? (Choose two.) routers VLANs 12. Which two characteristics describe a port in the STP blocking state? (Choose two.) discards data frames received from the attached segment receives BPDUs and directs them to the system module 13. What is the first step in the process of convergence in a spanning tree topo logy? election of the root bridge 14. In which STP state does a switch port transmit user data and learn MAC addre sses? forwarding 15. What is the purpose of VTP? maintaining consistency in VLAN configuration across the network 16. Which statement best describes adaptive cut-through switching? The switch initially forwards all traffic using cut-through switching and then c hanges to store-and-forward switching if errors exceed a threshold value. The switch initially forwards all traffic using cut-through switching and then c hanges to fast-forward switching if errors exceed a threshold value. 17. Using STP, how long does it take for a switch port to go from the blocking s tate to the forwarding state? 50 seconds Refer to the exhibit. The switches are interconnected by trunked links and are c onfigured for VTP as shown. A new VLAN is added to Switch1. Which three actions will occur? (Choose three.) Switch2 will add the VLAN to its database and pass the update to Switch3. Switch3 will pass the VTP update to Switch4. Switch4 will not receive the update. 19 Which Catalyst feature causes a switch port to enter the spanning-tree forwar ding state immediately? portfast