Vous êtes sur la page 1sur 2

Tractor Mounted Drilling Rigs

DURGA DT - 50,

Core Drill Rig


Technical Specifications

Description :- Durga DT-50 , is a Tractor Mounted Top drive all Hydraulically operated core Drilling Rig taking main power from Tractor
Engine, is designed for Geo-technical investigation (Geological survey), soil sampling application capable of drilling to a maximum depth of
100 Mt. (300 feet)

Drilling Capacity

Core Drilling Parameters

SI FPS
Drilling Sizes & Drilling Depths

100 m 300 Feet


NW Drilling (core 54.0 mm)
50 m 100 Feet
NX Casting (88.9 mm Drilling)

Mast Structure :- Sturdy structural Channel type mast of electrically welded construction, main members made out of heavy duty
structural steel channels reinforced with suitable cross members, so that it will be strong enough to withstand the varying drilling loads.

5000 mm
Mast Length
4000 mm
Rotary Head Travel
225 mm
Centraliser Opening
with hydraulic cylinder
Raising and Lowering
3m
Max. Rod handling Capacity

Tophead Rotary Drive :- Heavy-duty hydraulic driven Top head Rotation unit having infinitely variable speed (0 to 500rpm) will be
provided. This unit travels on the Mast and is of sturdy construction to absorb sudden & varying shock loads generally encountered during
drilling operations.

0-500 rpm
Output Speed
60 Kgm
Output Torque
Spur Gears
Types of Gears
OMT 200/Orbital
Drive Motor type
01 No.
No. of Motors

Feed System :- Feed system is provided with adequate travel for handling drill pipes upto 3.0 Mt long.The feed and hoist are actuated by a
suitable hydraulic cylinder with wire rope and pulley arrangement.

The feed system has the following capabilies

4500 kgf
Max. Pull Up Force
2400 kgf
Max. Pull Down Force
40 m/min
Max. Pull Up Speed
65 m/min
Max. Pull Down Speed
1:3
Reeving Ratio (Wire Rope)

The feed system will be incorporated with Hold back arrangement to control and limit weight on bit, rapid and slow feed arrangement to suit
the variable ground conditions.
Hydraulic System

160 kg/cm2
Max. Operating Pressure
150 Lts
Hydraulic Tank Capacity
10 microns
Filtration(Nom.) - Return Line

Prime Mover :- Power required for the rig hydraulics shall be drawn from the tractor engine through the out put shaft (PTO).

Stabilizers Cylinder :- System consists of three hydraulic leveling jacks with 'Reverse flow restricted valves to ensure safe operation.
Two numbers are at the front (Operator side) of the rig controlled by two separate valves and one jack at the rear side of the rig controlled by
a single valve.

Hydraulic cylinder
Type
3 Nos
No. of Jacks

Breakout Wrench ( optional ):- The Drill Rig is equipped with hydraulic breakout wrench for tightening and loosing of drill pipes and
the hammer.

80 mm 3 Inch
Cylinder Bore Diameter
300 mm 12 Inch
Stroke

Water Injection Pump :- Triplex plunger pump shall be used for DTH Drilling.

36 lpm
Capacity
40 bar
Max Pressure

Winch Assembly ( optional ):- Hydraulically operated wire line winch is mounted on mast to handle the casing pipes, drill pipes and
other handling tools.

800 kgf
Line Pull (Bare Drum)
40 Mt./min
Line Speed (Bare Drum)

Air Compressor ( optional )

Air compressor of suitable capacity as mentioned can be used for carrying out the DTH drilling activity.

450 cfm/150 psi


Air Compressor
Reputed make
Make

Note: the compressor shall be mounted on separate two wheel single dummy axle waith mechanical stabilizers quantity one number.

Air Line Lubricator :-Air line lubricator of capacity mentioned below shall be mounted for the supply of lubricating Oil to the hammer.

600 cfm/200 psi


Capacity
Reputed make
Make

Vous aimerez peut-être aussi