Académique Documents
Professionnel Documents
Culture Documents
Owner's Manual
Movement switches light, alarms and much more - for your convenience and safety.
The L 900 Series lamp can be installed and ready for operation quickly at the front door, garage, patio or carport, in a
stairway, storeroom or basement.
Installation Instructions
Caution: Read the entire instruction book before you start installation.
Principle of Operation
The built-in pyroelectric infrared sensor detects the invisible heat radiation emitted by moving people or cars. The thermal
radiation detected is converted electronically, and switches on light. No thermal radiation is detected through barriers such as
walls or panes of glass.
After all connections are made and the lamp The set angle of detection is 140°. This is 20°. (May be easily cut with scissors - see
is securely fastened to the junction box or adjustable in three ways: function and calibration).
conduit; the sys-tem can be turned on. Now A. Swivel on a horizontal plane by 130°.
you need to design your detection zone. B. Swivel on a vertical plane by 65°. These features allow you to focus your lamp
We recommend setting the unit to the C.Use of shrouds to customize the angle from in smaller areas optimizing your zone
minimum time when adjusting the detection 20° coverage to eliminate interference from
zone or carrying out a performance test. to 140°. These shrouds are manufactured so street traffic and other undesired triggering of
they can be broken off into 1/8" sections to the unit.
A = Detection range B= Sneak by guard
further customize your zone in increments of
The large angle through which it can swivel (130° horizontally and 65° vertically) allows the detection
zone to be selected freely within a range of 270°.
Attention: The sensor may not be tilted to face upwards. The sensor must be aimed at least 15° below
horizontal.
Installation
Conduit Installation
Caution: The installation involves connecting the unit to the power mains. 120 Volts can be lethal. First switch off power and
check that the circuit is dead by means of a voltage tester. Make sure that circuit remains interrupted. In case of doubt contact a
qualified electrician. The location should be at least 20" from any lamps because its thermal radiation could trigger the system.
The mounting height should be 6'-8'.
1. Fix a standard conduit fitting to the conduit and lead wires through conduit fitting and central hole of the mounting
plate.
2. Place mounting plate onto the conduit fitting through central hole and fix it with a lock nut. Secure mounting plate to
wall using screws provided or screws appropriate for the mounting surface.
3. Connect wires inside the connecting compartment of the unit using enclosed wire nuts according to the schematic
printed on the mounting plate.
4. Fix lamp to the mounting plate and fasten the screw.
5. Apply caulking around edge of back plate to assure water tight fit.
Calibration
Operation
Operation
In order to switch on the light without a heat source in the detection zone, switch the power on momentarily. This will activate the
light for the selected period of time.
Maintenance
The fresnel lens should be periodically wiped clean with a damp cloth if it gets dirty. Do not use any cleansing materials.
Caution:
The lamp is not suitable for special burglar alarm systems since it lacks the sabatoge protection required for this use.
Troubleshooting
Lamp without power ■ fuse has blown, not switched on, break in switch, check wiring with volt age
wiring tester
Lamp will not switch on ■ during daytime operation, light threshold ■ change setting
set to night time operation
Lamp will not switch off ■ constant movement in monitoring zone ■ check detection zone, and readjust
or shroud if necessary
Lamp switches on when ■ cars in street are monitored ■ readjust detection zone or shroud
it should not
Power. max. 60 W
Switching capacity incandescent lamps, halogen lamps, max. 600 W Tungsten load 5A max.
fluorescent lamps 300 VA Electric Discharge
Detection angle of sensor/plane: 140° horizontally (A), 90° horizontally (B) 8°
vertically (A) + (B)
Swivelling range of sensor. Tilting range of 130° horizontally 65° vertically
sensor.
Adjustable detection zone: 270° horizontally
Operating guarantee
Limited Warranty
STEINEL America, Inc./ STEINEL Canada Inc. (the Company) warrants to the original end-user purchaser (the Purchaser) that
its lamp (the Product), if properly operated and maintained, and used under normal conditions, shall be free from defects in
workmanship and materials for a period of three (3) years from the date of purchase. The obligation of the Company, and
Purchaser's sole and exclusive remedy here-under, shall be limited to one of the following, at the Company's option:
1. The repair or replacement of the Product.
2. In the event the Company is unable to repair or replace the Product, the Purchaser shall be entitled to a refund of the
purchase price paid for the Product.
The Company shall have no obligation under this Limited Warranty for ordinary wear and tear of the Product, or if the Product is
modified by any other person or organization.
The Company will inspect the Product within thirty (30) days after it receives the Product and the requested information. If the
Company determines that a defect covered by this Limited Warranty exists, within thirty (30) days after the inspection, the Com-
pany or a party designated by the Company will attempt to make repair or replacement of the Product. If this is not possible, a
refund of the purchase price paid for the Product will be paid to the Purchaser.
Disclaimers of warranties
The warranties contained herein are expressly in lieu of any other expressed or implied warranties, or any other obligation on
the part of the company. Any implied warranty of merchantability or fitness for a particular purpose shall expire one (1) year after
the date the product is purchased by the original end-user purchaser. Any models, drawings, plans, specifications, affirmations
of fact, promises, or other communications by the company with reference to the performance of the product are solely for the
convenience of the purchaser and shall not in any way modify the expressed warranties and disclaimers set forth herein. The
purchaser acknowledges it is purchasing the product solely on the basis of the commitments of the company as expressly set
forth herein. No agents or other parties are authorized to make any warranties on behalf of the company or to assume for the
company any other liability in connection with the product. Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
Consequential damages
The Company shall not be liable for any incidental or consequential damages arising from the use of the Product by the
Purchaser, the breach of any warranties, the failure to deliver, delay in delivery, delivery in non-conforming condition, or for any
other breach of contract or duty between the Company and the Purchaser.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
Limitation of actions
Any action resulting from the breach of any warranty contained herein by the Company must be commenced within one (1) year
after the cause of action accrues. In no event shall the Company's total liability for any or all breaches of any warranty exceed
the actual purchase price of the Pro-duct.
Other rights
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
STEINEL America Inc. 9051 Lyndale Avenue South Bloomington, MN 55420 Tel.: (001)612-888-5950
Fax: (001) 612-888-51 32 Toll-free: 1-800-852-4343
STEINEL Canada Inc. 108-3070 Norland Avenue Burnaby B.C. V5B3A6 Tel.: (604)299-3506 Fax: (604)299-1222