Académique Documents
Professionnel Documents
Culture Documents
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
1 Which software is typically used on a remote PC to access the enterprise through the Internet via a secure tunnel?
Telnet client
VPN client
FTP client
web browser
2 Which Frame Relay component provides connection status information about PVCs in the network?
CIR
LMI
DLCI
FECN
3
Refer to the exhibit. The network is running EIGRP with the default summarization enabled. Users who are connected to both R1 and R3
are complaining of intermittent connectivity. What should be done to solve this problem?
Use RIPv1 instead of EIGRP.
4 What are two WAN protocols that define parameters for data encapsulation? (Choose two.)
PPP
V.35
X.21
HDLC
EIA/TIA-232
5 Why would a network administrator want to limit the size of failure domains when designing a network?
to eliminate the effects of Ethernet collisions
to eliminate the need to block broadcast packets at the edge of the local network
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
RSTP ports, that are not discarding, immediately transition to the forwarding state.
7
Refer to the exhibit. What is the lowest cost OSPF path for traffic that is sourced from H2 and destined for H3?
R3 to R5
R3 to R2 to R5
R3 to R4 to R5
R3 to R2 to R1 to R5
8 What is the correct wildcard mask to define the supernet 192.168.0.0/22 in an ACL?
0.0.0.31
0.0.0.255
0.0.3.255
0.0.7.255
0.0.255.255
Refer to the exhibit. Both switches have been configured with static VLANs. Host A and host C belong to one VLAN and host B and D
belong to another VLAN. However, the hosts within the same VLAN are unable to communicate with each other.
Ensure that both switches are configured for the same native VLAN.
Ensure that the ports connecting the two switches are configured as trunk ports.
Ensure that both switches are configured with an IP address in the same subnet.
10 Which IP address and wildcard mask would be used in an ACL to identify all hosts that are in the same subnet as host 192.168.16.43/28?
192.168.16.0 0.0.0.15
192.168.16.0 0.0.0.31
192.168.16.16 0.0.0.15
192.168.16.32 0.0.0.15
192.168.16.43 0.0.0.31
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
11
What is the term for the value 2172416 that is highlighted in the output of the show ip eigrp topology command?
feasible distance of the successor
PAP sends the password encrypted and CHAP does not send the password at all.
PAP uses a two-way handshake method and CHAP uses a three-way handshake method.
PAP sends the password once and CHAP sends the password repeatedly until acknowledgement of authentication is received.
14 Which two statements are true about the native VLAN on a switch? (Choose two.)
It requires a special VLAN ID tag.
Untagged frames that are received on a trunk become members of this VLAN.
15
Refer to the exhibit. Router1 and Router2 are both running RIPv2 with autosummarization disabled.
Which subnet mask will Router1 associate with network 192.168.4.16/28?
255.255.0.0
255.255.240.0
255.255.255.0
255.255.255.240
255.255.255.248
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
usually has an administrative distance greater than routes learned from a dynamic routing protocol
17
Refer to the exhibit. Users on the 172.30.20.0/24 network are unable to access any of the servers located on the 192.168.0.0/23 network.
Given the network topology and OSPF configuration, what two problems exist in this network? (Choose two.)
There is a routing loop occurring between all three routers.
18 A network administrator wants to deny responses to ping requests. Which ACL statement denies ping responses while not affecting other traffic?
access-list 123 deny tcp any any eq 80
19
Refer to the exhibit. A network support technician has been asked to set an IP address on one of the FastEthernet interfaces on a new router.
What is causing the interface to reject the address?
The IP address is already in use.
20
Refer to the exhibit. Which Telnet session will be blocked as a result of the displayed commands?
the session from host A to host B
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
IP is used to specify all TCP/IP protocols including TCP, UDP, ICMP and routing protocols.
Traffic can be filtered on source and destination address, protocol, and specific port number.
22
Refer to the exhibit. R1 and R2 are connected via serial interfaces. Both interfaces show that there is Layer 2 connectivity between them. T
administrator verifies that CDP is operational; however, pings between the two interfaces are unsuccessful. What is the cause of this conne
problem?
no set loopback
incompatible bandwidth
incorrect IP address on R1
incompatible encapsulation
An ACL is active immediately after it has been created in global configuration mode.
A router compares a packet to all statements of an ACL before permitting or denying access through an interface.
24
Refer to the exhibit. All routers are configured to use the EIGRP routing protocol, and the network administrator has configured the serial
interface with the displayed commands. Which summary route will show in the routing table of R1 as a result of these commands?
a route pointing to the FastEthernet0/0 interface
25
Refer to the exhibit. All hosts on network 172.16.1.0/24 except the host 172.16.1.5 should be denied access to network 172.16.4.0/24. All other
networks should be accessible. The ACL is configured on both routers. Which sequence of commands will accomplish this goal?
A(config)# interface fastethernet0/0
A(config-if) ip access-group 10 in
A(config)# interface serial0/0/0
A(config-if) ip access-group 10 out
B(config)# interface fastethernet0/0
B(config-if) ip access-group 10 out
B(config)# interface fastethernet0/1
B(config-if) ip access-group 10 out
B(config)# interface serial0/0/1
B(config-if) ip access-group 10 out
Showing 5 of 11 <Prev Next>
Page:
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
26
Refer to the exhibit. Which IP address can be used at the Fa0/0 interface of R1 to enable host A to access the Internet?
192.168.1.65/27
192.168.1.32/27
192.168.1.63/27
192.168.1.61/27
27
Refer to the exhibit. What is the correct summary address for the contiguous address group that is shown?
172.18.8.0/22
172.18.8.0/23
172.18.8.0/24
172.18.8.0/25
172.18.8.0/28
28 If a modem is being used to connect to an ISP, which WAN connection type is being used?
leased line
cell switched
circuit switched
packet switched
29 What do companies gain from the services performed at the enterprise edge?
faster communication with server farms
enhanced performance and reliability through VLANs and redundant trunk links
30
Refer to the exhibit. EIGRP has been configured for all routers in the topology. Given the exhibited metric values, which path will be selected by the
DUAL algorithm as a successor and feasible successors or feasible successor for traffic that travels from router A to router E?
Path A-B-E will be selected as a successor. Both paths A-C-E and A-D-E will be selected as feasible successors.
Path A-D-E will be selected as a successor. Both paths A-B-E and A-C-E will be selected as feasible successors.
Path A-B-E will be selected as a successor. Path A-C-E will be selected as a feasible successor.
Path A-D-E will be selected as a successor. Path A-B-E will be selected as a feasible successor.
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
31 If an authentication protocol is configured for PPP operation, when is the client or user workstation authenticated?
prior to link establishment
32
Refer to the exhibit. R1 is using the default OSPF operation. Which IP address will be used as the router ID of R1?
192.168.201.1
172.16.1.1
10.10.10.1
10.1.1.1
33 What are two ways VLAN memberships can be created in an enterprise network? (Choose two.)
manually configuring the switch ports to be part of a VLAN
implementing an access list that specifies which devices are placed into specific VLANs.
associating MAC addresses to specific VLANs in a VLAN management policy server database
34
Refer to the exhibit. A packet with a destination IP address of 192.168.1.22 has entered router R1. How will this packet be routed?
It will be dropped.
35 An administrator wants to configure a new Cisco Catalyst 2960 switch in order to manage the switch remotely.
After configuring the vty lines to allow login, which set of commands should the administrator enter?
Switch(config)# line console 0
Switch(config-line)# password cisco
Switch(config-line)# login
Switch(config-line)# exit
Switch(config)# interface vlan 1
Switch(config-if)# ip address 192.168.1.5 255.255.255.0
Switch(config-if)#exit
Switch(config)# line console 0
Switch(config-line)# password cisco
Switch(config-line)# login
Switch(config-line)# exit
Switch(config)# ip default-gateway 192.168.1.1
Switch(config)# interface vlan 1
Switch(config-if)# ip address 192.168.1.5 255.255.255.0
Switch(config-if)# no shutdown
Switch(config-if)# exit
Switch(config)# ip default-gateway 192.168.1.1
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
36 Which two statements describe how the information contained in a BPDU is used by a switch? (Choose two.)
to set the duplex mode of a redundant link
37
Refer to the exhibit. OSPF is enabled and the network is fully converged. Which two routers will be designated as the DR and BDR, if all the
routers are booted at the same time? (Choose two.)
R1 will be the DR.
R4 will be the DR.
38
Refer to the exhibit. The network administrator configured the routers using the displayed commands, but the network fails to converge.
What can the network administrator do to solve this problem?
Issue the network commands correctly on both routers.
39 What are three correct host addresses in the 172.16.0.0/17 network? (Choose three.)
172.16.0.255
172.16.16.16
172.16.127.127
172.16.128.1
172.17.1.1
172.18.1.1
40
Refer to the exhibit. EIGRP has been configured on all routers in the network with default values.
Which route will be installed in the routing table of R1 to reach the 10.1.2.0/24 network?
The route through R2 will be installed.
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
41
Refer to the exhibit. Host A originates and sends broadcast frames to the network. Which hosts will receive the broadcast frames?
hosts B and C
hosts D and G
hosts A, B, and C
hosts A, D, and G
all hosts
42 What information is displayed in the output of the show version command on a router?
interface addresses
43
Refer to the exhibit. Routers R1 and R2 are directly connected via interface Serial0/0 on each router but they are unable to communicate. W
could be the cause of the problem?
The MTU is too high on both routers.
44
Refer to the exhibit. The network administrator has implemented NAT on R1. Which two addresses are valid inside global addresses? (Cho
two.)
192.168.1.1
192.168.1.2
198.133.219.1
198.133.219.102
198.133.219.103
45 What will allow a LAN switched network to maintain VLAN configuration consistency across the network?
Enable CDP on all switch access ports.
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
Close Window
Assessment System
Take Assessment - DRSEnt Final - CCNA Discovery: Introducing Routing and Switching in the
Enterprise (Version 4.0)
Time Remaining:
46 A RIPv2 enabled router has been configured with the redistribute static command. What function does this command serve?
creates a default route
establishes a backup static route which can be used if the dynamic routing protocol fails
47
Refer to the exhibit. All routers are configured to use OSPF with the default configuration. The network administrator wants to ensure that R
be the DR when the routers are booted.
What are two ways the network administrator could accomplish this goal?
Configure the OSPF priority value of the Fa0/0 interface of R1 to 0.
Configure the router ID of R2, R3, and R4 to a higher value than R1.
Change the priority value of the Fa0/0 interface of R2, R3, and R4 to 255.
Configure a loopback interface on R1 with an IP address higher than any IP
address on the other routers.
Configure the OSPF priority value of the Fa0/0 interface of R1 to a higher value than the Fa0/0 interface of any other router.
48
Refer to the exhibit. What is the purpose of the command: RouterA(config)# access-list 1 permit 192.168.16.0 0.0.0.255?
It identifies traffic on all inside interfaces to be translated and given access to the ISP router.
It identifies traffic from the fa0/1 interface to be translated and given access to the ISP router.
It allows traffic from the ISP to reach all of the inside interfaces.
It identifies traffic from the fa0/0 interface to be translated and given access to the ISP router.
49
Refer to the exhibit. The network administrator has used classless routing in the network. What is the result of running the displayed command?
All packets that are destined for address 10.12.0.1/22 will be forwarded via serial0/0/0.
All packets that are destined for address 10.12.14.0/22 will be forwarded via serial0/0/0.
All packets that are destined for address 10.12.16.1/22 will be forwarded via serial0/0/0.
All packets that are destined for address 10.12.15.255/22 will be forwarded via serial0/0/0.
50
Refer to the exhibit. The network administrator has configured R1, R2, and R3 to use RIPv2, and the network is fully converged. The hosts
the internal network are able to access R2, but they are unable to access the Internet.
Configure a default route on R2 via Serial0/0/0 and propagate it to R1 and R3 using RIPv2.
Close Window
All contents copyright 1992-2010 Cisco Systems, Inc. Privacy Statement and Trademarks.
s