Académique Documents
Professionnel Documents
Culture Documents
!"#$#%%&'
1. SCSI Devices
2. IDE Devices
3. Network Adapter
4. Internal Modem & Sound Card
5. Extra Hard Disks (You have to have at least one to complete the installation)
6. Cd Drive or DVD Drive (If you are installing from the local hard disk)
7. Upgrade Computer BIOS if possible
2. !$'
Click on start. Click on Run
V
or
Click on Start >> Control Panel >> Administrator Tools >> Event Viewer
Click on Application
(In vista click on windows Logs and then application)
Here you need to look for red X with error reports. This will let you know what caused your pc to crash last time or
program conflicting on your PC. Advisable to remove the program and then check if your PC works better or not.
Ä ()& to fix
STOP: 0×0000000A | Error - IRQL_NOT_LESS_OR_EQUAL
How to Repair windows - Check this link on how to run windows repair
* !"+,
Check If any of your RAM is malfunctioning. If you have 2 rams installed then try removing one them and reboot PC.
Poor and damaged RAM can also cause such errors.
å-c
.
/å /
This Stop Error explains that requested data was not in memory. Defective memory (including main
memoy, L2 RAM cache, video RAM) or incompatible software (including remote control and antivirus
software) might cause this Stop error.
%+$
Hardware failure (memory, processor, or motherboard).
Anti-virus software that is running on your computer.
Drivers installed by third-party software.
Disable any antivirus running on your computer.
STOP: 0x0000000a | STOP: 0x0000001e | STOP: 0x00000050
$%%#$&+'
.
('#+%$('
Look for software causing error in control panel >> Add remove programs >> Find the software and
uninstall
c
This Stop error indicates that indicates that the Windows XP kernel detected an illegal or unknown
processor instruction. The problem can be software or hardware related.
%+$
Hardware failure (memory, processor, or motherboard)
Anti-virus software that is running on your computer.
Drivers installed by third-party software.
Disable any antivirus running on our computer
STOP: 0x0000000a | STOP: 0x0000001e | STOP: 0x00000050
c
4c5 cc6
5+7%$' $(
4c8
*5
5
5
9
0
Registry
$(0
,+%%"
4c
4c
$(Ä3&$$%%#$&+'c
4c
Look for software causing error in control panel >> Add remove programs
Uninstall
+
Cause Of Error BSOD Error || STOP: 0×0000007B | INACCESSIBLE_BOOT_DEVICE ||Troubleshooting Stop
0×0000007B or ³0×4,0,0,0ļ Error
Reboot Your PC, press F8 key continously while the PC is rebooting until a black window appears. Select
command prompt from the list. Now on the Dos window
Type
chkdsk c: /f /r
Enter
(you may get a prompt to press Y/N) Press Y which means that check disk command will run on net boot
UP. Please allow the commad to run on next boot UP and
NOTE: the /f command automatically fixes any errors encountered, the /r command locates bad sectors
and recovers readable information
This will definately help to fix any drive related errors and speed up Your PC performance
Tech Advise:2
If you added new hardware recently remove and replace it to determine if it is causing or contributing to
the problem.
Tech Advise:3
Registry
+
Cause Of Error BSOD Error || Stop: 0×0000007F | UNEXPECTED_KERNEL_MODE_TRAP
c
0
Check Devise Manager for any driver conflict. Update drivers.
:
%%c!
Click On Start Menu >> Right Click On My Computer >> Click On properties >>Device Manage r>>
Double Click on DVD/CD ROM
& then Right Click On Properties >> Click On Driver >> Click On Rollback Driver & then Click Ok.
+
cause Of Error BSOD Error||STOP: 0x0000009F | DRIVER_POWER_STATE_FAILURE
This error generally occors while shutting down or moving out or standby or Hibernate Mode.
While Shutting down Suspending or resuming from Standby mode Suspending or resuming from
hibemation
c
0
Click On Start Menu >> Right-click On My Computer & then click Properties.
Click the Advanced tab >> Under Performance >> click Settings.
Click the Advanced tab >> Under Virtual Memory >> click Change.
Click the Advanced tab >> Under Performance >> click Settings.
Click the Advanced tab >> Under Virtual Memory >> click Change.
+
This Stop error indicates that the system attempted to access pageable memory using a kernel process
IRQL that was too high.
The major cause is bad devise driver or by a faulty or mismatched RAM or damaged pagefile.
c
!"#$%
Update your Video Adapter or install the latest Drivers for Windows XP.
Replace your Video Card
:
c &
'( '( ) *
0
:
#';+
It is important to defrag your PC once a month to keep the performance of the PC up to date
Click on start >>> Programs >> System Tools >> Disk Defragmentor
Defrag will help to clean any bad sectors on drive, increase disk space, speed up your PC performance
Ä
Reboot Your PC, press F8 key continously while the PC is rebooting until a black window appears. Select
command prompt from the list. Now on the Dos window
Type
chkdsk c: /f /r
Enter
(you may get a prompt to press Y/N) Press Y which means that check disk command will run on net boot
UP. Please allow the commad to run on next boot UP and
NOTE: the /f command automatically fixes any errors encountered, the /r command locates bad sectors
and recovers readable information
This will definately help to fix any drive related errors and speed up Your PC performance
*
Reconnect the drive that contains the corrupted NTFS volume.
Restart the computer & then run the following command on the corrupted NTFS volume:
chkdsk driveletter: /f
After you use the Chkdsk tool to repair the corrupted NTFS volume, rename
%SystemRoot%\System32\Drivers\NTFS.old to NTFS.SYS, and then shut down and restart the computer.
Cause Of Error V ! ! V" "# V$
c &
'+&
'+,-$%.$/0$/12
This error is caused when a registry hive file could not be loaded. The may be missing or corrupt. It may
be caused by hard disk failure or some other hardware problem.
%+$
1. Start your computer by running the Recovery Console, run the chkdsk /p command on the drive, and
then restart your
computer.
2. When Windows loads, press SPACE BAR when the "Load Last Known Good" message appears.
c
$(
-
0
Please verify that the RAM is the correct type for this installation & is correctly rated for speed voltage
& other parameters required by your specific computer.
If everything is correct
contact the manufacturer of your computer¶s motherboard for BIOS updates.
:
Ä
Reboot Your PC, press F8 key continously while the PC is rebooting until a black window appears. Select
command prompt from the list. Now on the Dos window
Type
chkdsk c: /f /r
Enter
(you may get a prompt to press Y/N) Press Y which means that check disk command will run on net boot
UP. Please allow the commad to run on next boot UP and
This will definately help to fix any drive related errors and speed up Your PC performance
Cause Of Error BSOD Error || Stop 0x0000002E or DATA_BUS_ERROR
The cause is typically failed or defective RAM including motherboard Level 2 cache or video memory
incompatible or mismatched memory hardware
Or when a device driver attempts to access an address in
The 0x8xxxxxxx range that does not exist does not map to a physical address
A Stop 0x2E message can also indicate hard disk damage caused by viruses or other problems
c
-
Äå, ; ,
0
In the registry editor navigate to the subkey HKEY LOCAL MACHINE SYSTEM CurrentControlSet Control
Session Manager\Memory Management
Double click on PagedPoolSize and SystemPages to view the value for each entry
If PagedPoolSize is not zero assign a value of 0
If SystemPages is not zero assign a value of 40000 for systems with 128 MB or less of memory or
110000 for systems with 128 MB to 256 MB of memory
For systems with more memory do not increase the SystemPages value above 110000 without contacting
Microsoft technical support
Cause Of Error BSOD Error || 0x0000003F or NO_MORE_SYSTEM_PTES
The system Page Table Entries PTE are depleted or fragmented due to the system performing a large
number of input output actions
An application such as a backup program is improperly allocating large amounts of kernel memory
c
-
$(0
Reboot Your PC, press F8 key continously while the PC is rebooting until a black window appears. Select
command prompt from the list. Now on the Dos window
Type
chkdsk c: /f /r
Enter
(you may get a prompt to press Y/N) Press Y which means that check disk command will run on net boot
UP. Please allow the commad to run on next boot UP and
NOTE: the /f command automatically fixes any errors encountered, the /r command locates bad sectors
and recovers readable information
$(:
+
Cause Of Error BSOD Error || 0x00000077 or KERNEL_STACK_INPAGE_ERROR
Bad sectors in the virtual memory paging file or a disk controller error In extremely rare cases depleted
nonpaged pool resources can cause this error.
c
-
4<, , 33
0
Please do the following steps to fix BSOD Error || 0x00000079 or MISMATCHED_HAL Error
Cause Of Error BSOD Error || 0x00000079 or MISMATCHED_HAL
$(0
Bad sectors in the virtual memory paging file disk controller error virus infection or memory hardware
problems
This problem might be fix through inrease virtual Memory
For Windows XP
Reboot Your PC, press F8 key continously while the PC is rebooting until a black window appears. Select
command prompt from the list. Now on the Dos window
Type
chkdsk c: /f /r
Enter
(you may get a prompt to press Y/N) Press Y which means that check disk command will run on net boot
UP. Please allow the commad to run on next boot UP and
NOTE: the /f command automatically fixes any errors encountered, the /r command locates bad sectors
and recovers readable information
This will definately help to fix any drive related errors and speed up Your PC performance
$(Ä
Reinstall Operating System
+
Cause Of Error 0x0000007A or KERNEL_DATA_INPAGE_ERROR
A page of kernel data was not found in the pagefile and could not be read into memory
This might be due to incompatible disk or controller drivers firmware or hardware
c
-
0
Click On Start Menu >> Right Click On My Computer >> Click On properties >>Device Manage r>>
Double Click on DVD/CD ROM
& then Right Click On Properties >>Click On Driver>> Click On Rollback Driver & then Click Ok.
$(0
$(:
The Stop 0xC2 message indicates that a kernel-mode process or driver incorrectly attempted to perform
memory operations
c
$(
-
6)3
$(0
%%c!
Click On Start Menu >> Right Click On My Computer >> Click On properties >>Device Manage r>>
Double Click on DVD/CD ROM
& then Right Click On Properties >>Click On Driver>> Click On Rollback Driver & then Click Ok.
Cause Of Error BSOD Error || Stop 0x000000CE or DRIVER_UNLOADED_WITHOUT
The Cause of the problem can be due to the following reasons
Installing faulty drivers or system services If a driver is listed by name
c
$(
-
,cc6,
+ !!$å-$7
Reboot your PC and press F8 key continously until Menu appears in DOS mode.
Select command prompt from the list. Now in the command prompt type
!!=#=
(space after chkdsk & space after c: )
Enter
This may take some time. You may get an error >&&$!$!"+&$$+
7t"
Type Yes or Y
Enter
reboot
The /f command will fix the errors. The r /r command finds bad sectors and recovers information which is readable. A
reboot is required.
the /f command automatically fixes any errors encountered, the /r command locates bad sectors and
recovers readable information
+# $(
-
,cc6,
The error can be due to unexpected shut down or software conflict effecting the hard drive.
Sometimes bacause of the cache not written to drive properly causing
Sometimes the contents of the cache are not written to the drive properly causing such errors ||
c &
'+&
'+,-$%.$/0$/12
This error is caused when a registry hive file could not be loaded. The may be missing or corrupt. It may
be caused by hard disk failure or some other hardware problem.
%+$
1. Start your computer by running the Recovery Console, run the chkdsk /p command on the drive, and
then restart your
computer.
2. When Windows loads, press SPACE BAR when the "Load Last Known Good" message appears.
c
-
%%c!
Click On Start Menu >> Right Click On My Computer >> Click On properties >>Device Manage r >> Double Click on
DVD/CD ROM
& then Right Click On Properties >>Click On Driver>> Click On Rollback Driver & then Click Ok.
$(:
Reboot the System.
$(Ä
Reinstall the Operating System
Cause Of Error BSOD Error || 0x0000021A or STATUS_SYSTEM_PROCESS_TERMINATED
Windows XP switches into kernel mode and a user mode subsystem such as
Winlogon or the Client Server Runtime Subsystem CSRSS is compromised and security can no longer be
guaranteed Because
Windows XP cannot run without Winlogon or CSRSS this is one of the few situations where the failure of a
user mode service
can cause the system to stop responding