Académique Documents
Professionnel Documents
Culture Documents
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com
1. Before beginning the installation, carefully unpack and
identify all parts, referring to the illustration.
2. Turn power to the installation point OFF at circuit breaker.
3. Locate STEM with HEX NUT. Thread top end of STEM into
hex coupling on underside of CENTER COLUMN. Using pliers,
OUTLET BOX
thread HEX NUT against hex coupling and hand tighten until
CROSSBAR snug. Proceed to thread NIPPLE into the coupling underside
HOUSE SUPPLY and
SHAKE PROOF GROUND WIRES of JUNCTION BOX. Tighten until snug. Locate PLAIN
WASHER A
OUTLET BOX SCREWS WASHER and PLASTIC WASHER over end of NIPPLE and
LOCK NUT A ( not supplied ) thread HEX NUT onto the end of NIPPLE to secure them.
NIPPLE GREEN GROUND SCREW
Tighten until snug.
LOCK NUT B 4.Locate top edge of SHADE ASSEMBLY inside of the space
between the bottom edge of FIXTURE COVER and TABS. The
SHAKE PROOF CANOPY CHAIN LOOP
TABS will engage the SHADE ASSEMBLY. Proceed to locate
WASHER B FIXTURE SUPPLY SHADE ASSEMBLY with FIXTURE COVER and PLAIN
and GROUND WIRE
WASHER over end of NIPPLE. Secure by threading HEX NUT
FIXTURE CHAIN onto the end of NIPPLE and hand tighten until snug.
5.Locate CAP over end of NIPPLE and thread FINIAL onto the
CEILING CANOPY end of NIPPLE to secure it. Tighten until snug. Proceed to
INNER CEILING thread FIXTURE LOOP onto the nipple inside of FIXTURE
CANOPY and tighten until snug.
DECORATIVE 6.Locate DECORATIVE ARMS. Position one end of ARM onto
CEILING CANOPY LOCK RING
the LOOP on the side of FIXTURE CANOPY and position
FIXTURE SUPPLY another end onto the HOOK on the FIXTURE COVER. Repeat
and GROUND WIRE
this process to complete the rest arms.
7. ( For Canadian installations, please refer to Page 2)
Fasten the CROSSBAR to the OUTLET BOX with (2)OUTLET
FIXTURE LOOP BOX SCREWS(not supplied). Proceed to thread LOCK NUT
A and SHAKE PROOF WASHER A onto the top end of
NIPPLE. Thread NIPPLE into the center of CROSSBAR.
FIXTURE CANOPY Locate the LOCK NUT B onto the bottom end of the NIPPLE.
Tighten LOCK NUT A against CROSSBAR with plier until
LOOP snug.
8. Locate the FIXTURE CHAIN and determine desired hanging
height of fixture. Adjust chain by removing links if needed.
Please note that depending on chain material thickness, you
might be required to use chain pliers to spread links open.
DECORATIVE ARM
Proceed to attach one end of chain to FIXTURE LOOP,
attached to top of fixture. Pass the fixture wires through
CENTER COLUMN FIXTURE CHAIN alternating links. Proceed to pass the
fixture wires through the following mounting components in
this order: 1)CANOPY LOCK RING; 2)DECORATIVE
CEILING; 3) INNER CEILING; 4) CEILING CANOPY;
5) CANOPY CHAIN LOOP; 6) SHAKE PROOF WASHER B
and LOCK NUT B; 7) NIPPLE; 8) LOCK NUT A and SHAKE
STEM with HEX NUT PROOF WASHER A.
9. Making the connections:(2 people recommended for the
JUNCTION BOX CANDLE COVER remaining steps) Position the fixture under the ceiling
SOCKET
mounted outlet box. Pass SHAKE PROOF WASHER B over
the NIPPLE. Thread CANOPY CHAIN LOOP onto NIPPLE.
Thread LOCK NUT B down the NIPPLE, against the
CANOPY CHAIN LOOP and snug with pliers. Pass the wires
NIPPLE through the NIPPLE. Take up wire slack and trim wires so
PLAIN WASHER
PLASTIC WASHER that approx. 6” will remain inside outlet box. Proceed to
HEX NUT
attach the top of the FIXTURE CHAIN to the bottom of the
HOOK
CANOPY CHAIN LOOP. Using wire connectors(not
supplied) connect the HOUSE GROUND WIRE to the
FIXTURE TAB FIXTURE GROUND WIRE; connect the HOUSE WHITE
COVER
WIRE to the FIXTURE SUPPLY WIRE (WHITE or RIBBED
SIDE); connect the HOUSE BLACK(or RED) WIRE to the
FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE). Wrap
each connection with approved electrical tape.
10. With the proper connections made, proceed to push the
CEILING CANOPY, INNER CEILING and DECORATIVE
SHADE
CEILING upward over the OUTLET BOX. Be sure that all wires
ASSEMBLY are carefully tucked into the OUTLET BOX cavity. Secure
canopies against ceiling by threading CANOPY LOCK RING
onto the CANOPY LOOP. Tighten until snug.
PLAIN WASHER 11.Position CANDLE COVERS over SOCKETS. Install bulbs
HEX NUT referring to fixture markings and/ or labels for maximum
CAP wattage.
FINIAL 12. Restore power to the installation point ON. Retain this sheet
for future reference.
IS - SA2820
Page 2 of 3
2006 - 11-23
FIGURE 2: CRAWL SPACE / ATTIC CUT-AWAY
WASHER
CEILING JOISTS
COTTER
PIN (installed above 3/8-18 NIPPLE (INCLUDED)
HEX NUT)
JUNCTION BOX
CEILING CANOPY
FIXTURE CHAIN
IS - SA2820
Page 3 of 3
2006 - 11-23