Académique Documents
Professionnel Documents
Culture Documents
Temperature °C
Hot forming Normalizing Quenching Quenching Tempering Stress relieving
1100-900 860-870 870 860 600-650 50 under the temperature
air oil or polymer water air of
tempering
Soft Isothermal Full End quench Preheating Stress relieving
annealing annealing annealing hardenability test welding after welding
650-680 650 -- 850 300 600 furnace cooling
air coolin furnace to water AC1 AC3 MS Mf
(HB max 248) 500 after air 715 770 320 100
Mechanical and physical properties
Hot formed – hot rolled - rod mechan. properties for quenched and tempered condition EN 10083-3: 2006
size d / t Testing at room temperature (longitudinal)
mm R Rp 0.2 A% C% Kv HB
over to N/mm2 N/mm2 min. min. min. J min. for information
16/8 1200-1400 1000 9 40 -- 359-404
16/8 40/20 1100-1300 900 10 45 45 331-380
40/20 100/60 1000-1200 800 11 50 45 298-359
100/60 160/100 900-1100 700 12 55 45 271-331
160/100 250/160 800-950 600 13 55 45 240-286
d = diameter t = thickness
Table of tempering values at room temperature for round Ø 60 mm after quenching at 850 °C in oil
HB 525 500 468 450 371 319 271 240
HRC 53 51.5 49 46.5 40 34 28 22
R N/mm2 1950 1850 1700 1500 1260 1050 900 800
Rp 0.2 N/mm2 1450 1480 1450 1350 1980 950 700 680
A % 10 10 10 12 13 18 20 22
C % 48 50 52 58 62 68 68 70
Kv J -- -- -- -- -- -- -- --
Tempering at °C 100 200 300 400 500 600 650 700
LUCEFIN experience Forged round 520 mm quenching 870 °C in water, tempering 630 °C air
Depth from Longitudinal Testing
Heat Treatment R Rp 0.2 A% C% Kv +20 °C Kv -40 °C HB
surface N/mm 2 N/mm 2 J J
25 mm 930 828 18,6 64,0 -- 110-118-118 279
1/3 radius 900 750 15,4 60,0 -- 48-44-45 271
1/2 diameter 860 730 12,6 46,0 70-74-70 25-28-25 264
FATT (Fracture Appearance Transition Temperature)
°C -70 -60 -40 -20 0 +20 +50 +80 +18
% fibrosity 3 6 11 15 24 53 100 100 FATT 50
Kv average J 22 24 27 42 51 70 142 150 68
Chemical composition % ppm
C Si Mn P S Cr Mo Ni V Cu Sn As Sb Al H2 O2 N2
0.36 0.23 0.64 0.006 0.003 1.62 0.28 1.60 0.05 0.16 0.006 0.007 0.004 0.018 1.30 34 70
34CrNiMo6 1.6582 EN 10277-5: 2008 Lucefin Group
Hot rolled quenched and tempered after Cold drawn +QT +C Cold drawn +A +C obtained from hot rolled annealing
size Testing at room temperature (longitudinal)
mm R Rp 0.2 A% HB HB
over to N/mm2 N/mm2 min min for inform. max
5 b) 10 1000-1200 770 8 298-359 308
10 16 1000-1200 750 8 298-359 298
16 40 1000-1200 720 9 298-359 293
40 63 1000-1200 650 10 298-359 288
63 100 1000-1200 650 10 298-359 288
b) for thickness below 5 mm mechanical properties can be agreed before order placement
e) values valid also for +QT+C+SL