Académique Documents
Professionnel Documents
Culture Documents
1. General description
The 74HC138; 74HCT138 is a high-speed Si-gate CMOS device and is pin compatible with Low-power Schottky TTL (LSTTL). The 74HC138; 74HCT138 decoder accepts three binary weighted address inputs (A0, A1 and A3) and when enabled, provides 8 mutually exclusive active LOW outputs (Y0 to Y7). The 74HC138; 74HCT138 features three enable inputs: two active LOW (E1 and E2) and one active HIGH (E3). Every output will be HIGH unless E1 and E2 are LOW and E3 is HIGH. This multiple enable function allows easy parallel expansion of the 74HC138; 74HCT138 to a 1-of-32 (5 lines to 32 lines) decoder with just four 74HC138; 74HCT138 ICs and one inverter. The 74HC138; 74HCT138 can be used as an eight output demultiplexer by using one of the active LOW enable inputs as the data input and the remaining enable inputs as strobes. Not used enable inputs must be permanently tied to their appropriate active HIGH- or LOW-state. The 74HC138; 74HCT138 is identical to the 74HC238; 74HCT238 but has inverting outputs.
2. Features
s s s s s s Demultiplexing capability Multiple input enable for easy expansion Complies with JEDEC standard no. 7A Ideal for memory chip select decoding Active LOW mutually exclusive outputs ESD protection: x HBM EIA/JESD22-A114-C exceeds 2000 V x MM EIA/JESD22-A115-A exceeds 200 V s Specied from 40 C to +85 C and from 40 C to +125 C
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Conditions VCC = 5 V; CL = 15 pF
Min
Typ
Max
Unit
VI = GND to VCC
[1]
12 14 14 3.5 67
ns ns ns pF pF
17 19 19 3.5 67
ns ns ns pF pF
CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD VCC2 fi N + (CL VCC2 fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; (CL VCC2 fo) = sum of the outputs.
4. Ordering information
Table 2: Ordering information Package Temperature range Name 74HC138 74HC138N 74HC138D 74HC138DB 74HC138PW 74HC138BQ 40 C to +125 C 40 C to +125 C 40 C to +125 C 40 C to +125 C 40 C to +125 C DIP16 SO16 SSOP16 TSSOP16 plastic dual in-line package; 16 leads (300 mil); long body plastic small outline package; 16 leads; body width 3.9 mm plastic shrink small outline package; 16 leads; body width 5.3 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT38-1 SOT109-1 SOT338-1 SOT403-1 Description Version Type number
DHVQFN16 plastic dual in-line compatible thermal enhanced SOT763-1 very thin quad at package; no leads; 16 terminals; body 2.5 3.5 0.85 mm
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
74HC_HCT138_3
2 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Table 2:
Ordering information continued Package Temperature range Name Description plastic dual in-line package; 16 leads (300 mil); long body plastic small outline package; 16 leads; body width 3.9 mm plastic shrink small outline package; 16 leads; body width 5.3 mm plastic thin shrink small outline package; 16 leads; body width 4.4 mm Version SOT38-1 SOT109-1 SOT338-1 SOT403-1
DHVQFN16 plastic dual in-line compatible thermal enhanced SOT763-1 very thin quad at package; no leads; 16 terminals; body 2.5 3.5 0.85 mm
5. Functional diagram
Y0 1 1 2 3 A0 A1 A2 Y0 Y1 Y2 Y3 4 5 6 E1 E2 E3 Y4 Y5 Y6 Y7
mna370
15 14 13 12 11 10 9 7
Y1 Y2 Y3 Y4 Y5 Y6 Y7
15 14 13 12 11 10 9 7
2 3
4 5 6
E1 E2 E3
mna372
74HC_HCT138_3
3 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
A2
Y7
Y6 A1 Y5 A0 Y4 E1 Y3 E2 Y2 E3 Y1
Y0
001aae059
6. Pinning information
6.1 Pinning
74HC138BQ 74HCT138BQ
terminal 1 index area 16 VCC 15 Y0 14 Y1 13 Y2 12 Y3 11 Y4 10 Y5 9
001aae061
A0 A1 A2 E1 E2 E3 Y7 GND
1 2 3 4 5 6 7 8
A1 A2 E1 E2 E3 Y7
2 3 4 5 6 7 8 GND Y6 9 GND(1)
16 VCC 15 Y0 14 Y1 13 Y2 12 Y3 11 Y4 10 Y5
A0
74HC138 74HCT138
001aae060
(1) The die substrate is attached to this pad using conductive die attach material. It can not be used as supply pin or input.
74HC_HCT138_3
4 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
7. Functional description
Table 4: Control E1 H X X L E2 X H X L E3 X X L H L L L L H H H H
[1] H = HIGH voltage level; L = LOW voltage level; X = dont care.
L L H H L L H H
L H L H L H L H
H H H H H H H L
H H H H H H L H
H H H H H L H H
H H H H L H H H
H H H L H H H H
H H L H H H H H
H L H H H H H H
L H H H H H H H
74HC_HCT138_3
5 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
8. Limiting values
Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC IIK IOK IO ICC IGND Tstg Ptot Parameter supply voltage input clamping current output clamping current output current quiescent supply current ground current storage temperature total power dissipation DIP16 package SO16 package SSOP16 package TSSOP16 package DHVQFN16 package
[1] [2] [3] [4] For DIP16 package: Ptot derates linearly with 12 mW/K above 70 C. For SO16 package: Ptot derates linearly with 8 mW/K above 70 C. For SSOP16 and TSSOP16 packages: Ptot derates linearly with 5.5 mW/K above 60 C. For DHVQFN16 packages: Ptot derates linearly with 4.5 mW/K above 60 C.
[1] [2] [3] [3] [4]
Conditions VI < 0.5 V or VI > VCC + 0.5 V VO < 0.5 V or VO > VCC + 0.5 V VO = 0.5 V to (VCC + 0.5 V)
Min 0.5 65 -
Unit V mA mA mA mA mA C mW mW mW mW mW
74HC_HCT138_3
6 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Tamb = 40 C to +85 C
74HC_HCT138_3
7 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Table 7: Static characteristics 74HC138 continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VOL Parameter LOW-state output voltage Conditions VI = VIH or VIL IO = 20 A; VCC = 2.0 V IO = 20 A; VCC = 4.5 V IO = 20 A; VCC = 6.0 V IO = 4.0 mA; VCC = 4.5 V IO = 5.2 mA; VCC = 6 V ILI IOZ ICC input leakage current OFF-state output current quiescent supply current VI = VCC or GND; VCC = 6 V VI = VIH or VIL; VO = VCC or GND; VCC = 6.0 V VCC = 6.0 V; IO = 0 A; VI = VCC or GND VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VIL LOW-state input voltage VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V VOH HIGH-state output voltage VI = VIH or VIL IO = 20 A; VCC = 2.0 V IO = 20 A; VCC = 4.5 V IO = 20 A; VCC = 6.0 V IO = 4.0 mA; VCC = 4.5 V IO = 5.2 mA; VCC = 6 V VOL LOW-state output voltage VI = VIH or VIL IO = 20 A; VCC = 2.0 V IO = 20 A; VCC = 4.5 V IO = 20 A; VCC = 6.0 V IO = 4.0 mA; VCC = 4.5 V IO = 5.2 mA; VCC = 6 V ILI IOZ ICC input leakage current OFF-state output current quiescent supply current VI = VCC or GND; VCC = 6 V VI = VIH or VIL; VO = VCC or GND; VCC = 6.0 V VCC = 6.0 V; IO = 0 A; VI = VCC or GND 0.1 0.1 0.1 0.4 0.4 1.0 10.0 160 V V V V V A A A 1.9 4.4 5.9 3.7 5.2 V V V V V 0.1 0.1 0.1 0.33 0.33 1.0 5.0 80 V V V V V A A A Min Typ Max Unit
Tamb = 40 C to +125 C VIH HIGH-state input voltage 1.5 3.15 4.2 0.5 1.35 1.8 V V V V V V
74HC_HCT138_3
8 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Table 8: Static characteristics 74HCT138 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VIH VIL VOH Parameter HIGH-state input voltage LOW-state input voltage HIGH-state output voltage Conditions VCC = 4.5 V to 5.5 V VCC = 4.5 V to 5.5 V VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V VOL LOW-state output voltage VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V ILI IOZ ICC ICC input leakage current OFF-state output current quiescent supply current additional quiescent supply current pin An pin En pin E3 Ci VIH VIL VOH input capacitance HIGH-state input voltage LOW-state input voltage HIGH-state output voltage VCC = 4.5 to 5.5 V VCC = 4.5 to 5.5 V VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V VOL LOW-state output voltage VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V ILI IOZ ICC ICC input leakage current OFF-state output current quiescent supply current additional quiescent supply current pin An pin En pin E3 VI = VCC or GND; VCC = 5.5 V VI = VIH or VIL; VCC = 5.5 V; VO = VCC or GND; IO = 0 A VCC = 5.5 V; IO = 0 A; VI = VCC or GND per input pin; VI = VCC 2.1 V; other inputs at VCC or GND; VCC = 4.5 V to 5.5 V; IO = 0 A 675 562.5 450 A A A 0.1 0.33 1.0 5.0 80 V V A A A 4.4 3.84 V V Tamb = 40 C to +85 C 2.0 0.8 V V VI = VCC or GND; VCC = 5.5 V VI = VIH or VIL; VCC = 5.5 V; VO = VCC or GND; IO = 0 A VCC = 6.0 V; IO = 0 A; VI = VCC or GND per input pin; VI = VCC 2.1 V; other inputs at VCC or GND; VCC = 4.5 V to 5.5 V; IO = 0 A 150 125 100 3.5 540 450 360 A A A pF 0.0 0.15 0.1 0.26 0.1 0.5 8.0 V V A A A 4.4 3.98 4.5 4.32 V V Min 2.0 Typ 1.6 1.2 Max 0.8 Unit V V Tamb = 25 C
74HC_HCT138_3
9 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Table 8: Static characteristics 74HCT138 continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VIH VIL VOH Parameter HIGH-state input voltage LOW-state input voltage HIGH-state output voltage Conditions VCC = 4.5 V to 5.5 V VCC = 4.5 V to 5.5 V VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V VOL LOW-state output voltage VI = VIH or VIL IO = 20 A; VCC = 4.5 V IO = 4.0 mA; VCC = 4.5 V ILI IOZ ICC ICC input leakage current OFF-state output current quiescent supply current additional quiescent supply current pin An pin En pin E3 VI = VCC or GND; VCC = 5.5 V VI = VIH or VIL; VCC = 5.5 V; VO = VCC or GND; IO = 0 A VCC = 5.5 V; IO = 0 A; VI = VCC or GND per input pin; VI = VCC 2.1 V; other inputs at VCC or GND; VCC = 4.5 V to 5.5 V; IO = 0 A 735 612.5 490 A A A 0.1 0.4 1.0 10.0 160 V V A A A 4.4 3.7 V V Min 2.0 Typ Max 0.8 Unit V V Tamb = 40 C to +125 C
74HC_HCT138_3
10 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Conditions
Min
Typ
Max
Unit
41 15 12 12 47 17 14 14 47 17 14 14 19 7 6 67
ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns pF
74HC_HCT138_3
11 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Table 9: Dynamic characteristics 74HC138 continued Voltages are referenced to GND (ground = 0 V); CL = 50 pF unless otherwise specied. For test circuit see Figure 8. Symbol Parameter tTHL, tTLH output transition time Conditions see Figure 6 and 7 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V Tamb = 40 C to +125 C tPHL, tPLH propagation delay An to Yn see Figure 6 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V E3 to Yn see Figure 6 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V En to Yn see Figure 7 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V tTHL, tTLH output transition time see Figure 6 and 7 VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V
[1]
Min -
Typ -
Max 95 19 16
Unit ns ns ns
ns ns ns ns ns ns ns ns ns ns ns ns
CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD VCC2 fi N + (CL VCC2 fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; (CL VCC2 fo) = sum of the outputs.
74HC_HCT138_3
12 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
Table 10: Dynamic characteristics 74HCT138 Voltages are referenced to GND (ground = 0 V); CL = 50 pF unless otherwise specied. For test circuit see Figure 8. Symbol Parameter Tamb = 25 C tPHL, tPLH propagation delay An to Yn see Figure 6 VCC = 4.5 V VCC = 5 V; CL = 15 pF E3 to Yn see Figure 6 VCC = 4.5 V VCC = 5 V; CL = 15 pF En to Yn see Figure 7 VCC = 4.5 V VCC = 5 V; CL = 15 pF tTHL, tTLH CPD output transition time see Figure 6 and 7 VCC = 4.5 V power dissipation capacitance propagation delay An to Yn E3 to Yn En to Yn tTHL, tTLH see Figure 6 VCC = 4.5 V see Figure 6 VCC = 4.5 V see Figure 7 VCC = 4.5 V output transition time see Figure 6 and 7 VCC = 4.5 V propagation delay An to Yn E3 to Yn En to Yn tTHL, tTLH
[1]
Conditions
Min
Typ
Max
Unit
[1]
20 17 18 19 19 19 7 67
35 40 40 15 -
ns ns ns ns ns ns ns pF
44 50 50 19
ns ns ns ns
Tamb = 40 C to +125 C tPHL, tPLH see Figure 6 VCC = 4.5 V see Figure 6 VCC = 4.5 V see Figure 7 VCC = 4.5 V output transition time see Figure 6 and 7 VCC = 4.5 V 22 ns 60 ns 60 ns 53 ns
CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD VCC2 fi N + (CL VCC2 fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF;
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
74HC_HCT138_3
13 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
VCC = supply voltage in V; N = number of inputs switching; (CL VCC2 fo) = sum of the outputs.
12. Waveforms
VCC An, E3 input GND tPHL VOH Yn output VOL tTHL tTLH mna373 VM tPLH VM
Measurement points are given in Table 11. VOL and VOH are typical voltage output drop that occur with the output load.
Fig 6. Propagation delay input (An) and enable input (E3) to output (Yn) and transition time output (Yn)
VOL
tTHL tTLH mna374
Measurement points are given in Table 11. VOL and VOH are typical voltage output drop that occur with the output load.
Fig 7. Propagation delay enable input (En) to output (Yn) and transition time output (Yn) Table 11: Type 74HC138 74HCT138 Measurement points Input VM 0.5VCC 1.3 V Output VM 0.5VCC 1.3 V
74HC_HCT138_3
14 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
VI negative pulse 0V
tW 90 % VM 10 % tf tr tr tf 90 % VM 10 % tW VM VM
VI positive pulse 0V
VCC
VCC
PULSE GENERATOR
VI
VO
RL
S1
DUT
RT CL
open
001aad983
Test data is given in Table 12. Denitions test circuit: RT = Termination resistance should be equal to output impedance Zo of the pulse generator CL = Load capacitance including jig and probe capacitance RL = Load resistor S1 = Test selection switch
Fig 8. Load circuitry for measuring switching times Table 12: Type 74HC138 74HCT138 Test data Input VI VCC 3V tr, tf 6 ns 6 ns Load CL RL 15 pF, 50 pF 1 k 15 pF, 50 pF 1 k S1 position tPHL, tPLH open open tPZH, tPHZ GND GND tPZL, tPLZ VCC VCC
74HC_HCT138_3
15 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
D seating plane
ME
A2
A1
c Z e b1 b 16 9 MH w M (e 1)
pin 1 index E
5 scale
10 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.7 0.19 A1 min. 0.51 0.02 A2 max. 3.7 0.15 b 1.40 1.14 0.055 0.045 b1 0.53 0.38 0.021 0.015 c 0.32 0.23 0.013 0.009 D (1) 21.8 21.4 0.86 0.84 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.1 e1 7.62 0.3 L 3.9 3.4 0.15 0.13 ME 8.25 7.80 0.32 0.31 MH 9.5 8.3 0.37 0.33 w 0.254 0.01 Z (1) max. 2.2 0.087
Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT38-1 REFERENCES IEC 050G09 JEDEC MO-001 JEITA SC-503-16 EUROPEAN PROJECTION
16 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
SOT109-1
A X
c y HE v M A
Z 16 9
2.5 scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07 JEDEC MS-012 JEITA EUROPEAN PROJECTION A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3
8 o 0
17 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
c y HE v M A
16
Q A2 pin 1 index A1 Lp L (A 3) A
1
e bp
8
w M detail X
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.30 0.19 c 0.2 0.1 D (1) 5.1 4.9 E (2) 4.5 4.3 e 0.65 HE 6.6 6.2 L 1 Lp 0.75 0.50 Q 0.4 0.3 v 0.2 w 0.13 y 0.1 Z (1) 0.40 0.06 8 o 0
o
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC MO-153 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18
18 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm
SOT338-1
A X
c y HE v M A
Z 16 9
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 2 A1 0.21 0.05 A2 1.80 1.65 A3 0.25 bp 0.38 0.25 c 0.20 0.09 D (1) 6.4 6.0 E (1) 5.4 5.2 e 0.65 HE 7.9 7.6 L 1.25 Lp 1.03 0.63 Q 0.9 0.7 v 0.2 w 0.13 y 0.1 Z (1) 1.00 0.55 8 o 0
o
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT338-1 REFERENCES IEC JEDEC MO-150 JEITA EUROPEAN PROJECTION
19 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; SOT763-1 16 terminals; body 2.5 x 3.5 x 0.85 mm
A A1 E c
detail X
e1 b 7 v M C A B w M C y1 C
C y
1 Eh 16
8 e 9
15 Dh
10 X 2.5 scale 5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. 1 A1 0.05 0.00 b 0.30 0.18 c 0.2 D (1) 3.6 3.4 Dh 2.15 1.85 E (1) 2.6 2.4 Eh 1.15 0.85 e 0.5 e1 2.5 L 0.5 0.3 v 0.1 w 0.05 y 0.05 y1 0.1
Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. OUTLINE VERSION SOT763-1 REFERENCES IEC --JEDEC MO-241 JEITA --EUROPEAN PROJECTION ISSUE DATE 02-10-17 03-01-27
20 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
14. Abbreviations
Table 13: Acronym CMOS DUT ESD HBM LSTTL MM Abbreviations Description Complementary Metal Oxide Semiconductor Device Under Test ElectroStatic Discharge Human Body Model Low-power Schottky Transistor-Transistor Logic Machine Model
The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors. Section 4 Ordering information, Section 6 Pinning information and Section 13 Package outline: Added DHVQFN package information Section 10 Static characteristics: Added from the family specication Product specication -
74HC_HCT138_CNV_2 19970827
74HC_HCT138_3
21 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
III
Product data
Production
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
17. Denitions
Short-form specication The data in a short-form specication is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values denition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specication is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specied use without further testing or modication.
customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status Production), relevant changes will be communicated via a Customer Product/Process Change Notication (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specied.
19. Trademarks
Notice All referenced brands, product names, service names and trademarks are the property of their respective owners.
18. Disclaimers
Life support These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors
74HC_HCT138_3
22 of 23
Philips Semiconductors
74HC138; 74HCT138
3-to-8 line decoder/demultiplexer; inverting
21. Contents
1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 12 13 14 15 16 17 18 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Recommended operating conditions. . . . . . . . 6 Static characteristics. . . . . . . . . . . . . . . . . . . . . 7 Dynamic characteristics . . . . . . . . . . . . . . . . . 11 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 16 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 21 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 22 Denitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Contact information . . . . . . . . . . . . . . . . . . . . 22