Académique Documents
Professionnel Documents
Culture Documents
No: 45047
R05
(AERONAUTICAL ENGINEERING)
SET-1
3. For the cantilever beam of 1000 mm span of L section subjected to a load of 8KN at the free end at 300 to the vertical. Determine the bending stress at A and C.[16]
w w
For the fixed beam shown in fig. determine the order of redundancy and determine the deflection under the load. [8+8]
. w
tu jn
or w
. ld
m co
[8+8]
4. a) Define buckling and radius of gyration. b) Derive the bucking load equation for a column with both ends fixed. 5.
[8+8]
A hinged support beam column of 40*60 mm 2 of 1.5m long is subjected to an axial of 8 KN in addition to transverse concentrated load of 15 KN. Determine the maximum deflection and maximum stress in the column. E = 200 Gpa [16]
6. a) State and prove Castiglinos theorem. b) For the simple supported beam with U.D.L determine the maximum deflection using Castiglinos theorem. [8+8]
7.
Write the Equation of motion for the system shown in figure and develop the shiftiness matrix for the entire system. [16]
w w
. w
tu jn
or w
. ld
m co
[16]
*************
Code.No: 45047
R05
(AERONAUTICAL ENGINEERING)
SET-2
2.
w w
3.
. w
tu jn
or w
. ld
m co
For the fixed beam shown above determine the order of redundancy and draw the fixed and free bending moment diagrams. Also determine the maximum deflection. [16] For the unsymmetrical sector shown derive the equation for bending stress on the element dA Also locate the Neutral axis [16]
4. a) What is the difference between deflection and buckling . b) Derive the secant formula for an eccentrically loaded column with both hinged. 5.
A beam-column with both end hinged is subjected to an compressive load and a transverse load W at the centre. Determine the deflection at the center. [16]
.6.a) State and prove Castiglinos theorem. b) Determine the deflection in vertical direction using Castiglinos theorm.
7.
w w
. w
tu jn
or w
. ld
m co
[8+8]
[8+8]
EI-flexural rigidity.
For the beam shown determine the end reaction by using Rayleigh-Ritz method . Also draw the fixes and force bending moment diagram. [16]
8.
Write the equation of motion for the system shown in figure and develop over all still ness matrix. [16]
*************
w w
. w
tu jn
or w
. ld
m co
Code.No: 45047
R05
(AERONAUTICAL ENGINEERING)
SET-3
2.
3. a) What are the various cases of unsymmetrical bending . Explain with heat sketch. b) Explain moment of inertia and product of inertia .Determine the product of inertia for the triangle section. [8+8]
w w
For the frame shown in figure determine the order of redundancy and draw the BMD diagram [16]
. w
tu jn
or w
. ld
m co
4. a) Define column and classify the column bared a different end conditions.
b) What are the difference between long & short column and explain Rankine theory. [8+8] 5. A beam column is subjected to end moments followed by compressive load as shown in fig. Determine the deflection at the centre. [16]
6)
7.
w w
The fuselage bulk head is subjected to loading as shown. Determine the deflection at the point of loading using Castiglinos method. [16]
. w
tu jn
or w
. ld
m co
For the prismatic bar fixed at both ends determine the reactions at ends. A and B using Rayleigh Ritz method. Also draw the load diagram. [16]
8.
w w
For the system shown is figure, Write the equation of motion and establish over all stiffness matrix. [16]
. w
tu jn
or w
. ld
m co
*************
Code.No: 45047
R05
(AERONAUTICAL ENGINEERING)
SET-4
For the beam shown, determine the degree of redundancy and draw the fixed free bending moment diagram [8+8] 3. a) What are the various cases of Unsymmetry in a beam. b)
w w
. w
tu jn
or w
. ld
m co
For the unsymmetrical loading shown, determine the bending on the element dA and locate the Neutral axis. [8+8]
For a cantilever column loaded as shown, determine the buckling at free end.[8+8]
5. a) What are the various end condition for a beam column b) Determine the maximum deflection at the centre of a pin ended beam carrying a U.d.L; per unit length and a compressive load P at both the ends. [8+8] 6. State and prove Maxwells reciprocal theorem.
7.
w w
. w
tu jn
or w
. ld
m co
[16]
For the shaft in the above figure determine the reaction at the ends using Rayliegh- Ritz method Also draw the Torque diagram. [16]
8.
Derive the equation of motion for the system shown. Also develop the overall stiffness. [16]
w w
. w
tu jn
or w
. ld
m co
*************