Académique Documents
Professionnel Documents
Culture Documents
DEH-1330R/X1M/EW
ORDER NO.
CRT2558
DEH-1330R DEH-1300R
X1M/EW
X1M/EW
DEH-1310
Model No. CX-958 Order No. CRT2423
X1M/EE
- This service manual should be used together with the following manual(s):
Mech. Module Remarks S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
CONTENTS
1. 2. 3. 4. 5. 6. SAFETY INFORMATION ............................................3 EXPLODED VIEWS AND PARTS LIST .......................4 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...12 PCB CONNECTION DIAGRAM ................................34 ELECTRICAL PARTS LIST ........................................42 ADJUSTMENT..........................................................48 7. GENERAL INFORMATION .......................................52 7.1 DIAGNOSIS ........................................................52 7.1.1 TEST MODE ..............................................52 7.1.2 DISASSEMBLY .........................................55 7.1.3 CONNECTOR FUNCTION DESCRIPTION .......59 7.2 PARTS .................................................................60 7.2.1 IC................................................................60 7.2.2 DISPLAY ....................................................66 7.3 OPERATIONAL FLOW CHART ...........................68 8. OPERATIONS AND SPECIFICATIONS.....................69
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936 C PIONEER CORPORATION 2000
K-ZZA. OCT. 2000 Printed in Japan
DEH-1330R,1300R,1310
DEH-1330R,1300R,1310
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so and refer the repair to a qualified service technician. 1. Safety Precautions for those who Service this Unit. When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable results. Caution: 1. During repair or tests, minimum distance of 13cm from the focus lens must be kept. 2. During repair or tests, do not view laser beam for 10 seconds or longer. 2. A CLASS 1 LASER PRODUCT label is affixed to the bottom of the player. 3. The triangular label is attached to the mechanism unit frame.
4. Specifications of Laser Diode Specifications of laser radiation fields to which human access is possible during service. Wavelength = 800 nanometers
DEH-1330R,1300R,1310
2 5 4
10 1
12
11 6
NOTE:
- Parts marked by * are generally unavailable because they are not in our Master Spare Parts List. - Screws adjacent to mark on the product are used for disassembly.
Mark No. Description * * 7-5 7-6 8 9 10 Passport Warranty Card Carton Contain Box Protector
Part No.
See Contrast table(2)
CRY1157
See Contrast table(2) See Contrast table(2)
DEH-1330R,1300R,1310
(2) CONTRAST TABLE DEH-1330R/X1M/EW, DEH-1300R/X1M/EW and DEH-1310/X1M/EE are constructed the same except for the following:
Mark No. 1 7-2 7-3 7-4 * 7-5 Symbol and Description Cord Assy Owner's Manual Owner's Manual Installation Manual Passport DEH-1330R/X1M/EW CDE6467 CRD3276 CRD3277 CRD3278 CRY1013 CHG4159 CHL4159 Part No. DEH-1300R/X1M/EW CDE6467 CRD3276 CRD3277 CRD3278 CRY1013 CHG4158 CHL4158 DEH-1310/X1M/EE CDE6470 CRD3284 Not used CRD3285 Not used CHG4156 CHL4156
DEH-1330R,1300R,1310
DEH-1330R,1300R,1310
CDE6467 CKX-003 CEK1136 CD Mechanism Module(S8.1) CXK5203 Holder CNC5704 Cover Cushion Insulator Insulator Tuner Amp Unit Screw Screw Screw FM/AM Tuner Unit Holder Pin Jack(CN301) Terminal(CN403) Plug(CN901) Connector(CN601) Connector(CN605) Antenna Jack(CN402) Holder Holder Holder Heat Sink Case Unit Detach Grille Assy Screw Button(DETACH) Button(1-6, CLK) CNC9127 CNM5210 CNM6224 CNM6386 CWM7294 ASZ26P080FMC BPZ26P080FMC BSZ26P160FMC CWE1562 CNC8815 CKB1041 CKF1059 CKM1330 CKS3581 CKS3838 CKX1056 CNC8041 CNC8043 CNC9128 CNR1589 CXB4033
See Contrast table(2)
BPZ20P100FZK
See Contrast table(2)
CAC6822
(2) CONTRAST TABLE DEH-1330R/X1M/EW and DEH-1300R/X1M/EW are constructed the same except for the following:
Mark No. 32 34 42 43 53 Symbol and Description Detach Grille Assy Button(DETACH) Cover Keyboard Unit Grille Unit Part No. DEH-1330R/X1M/EW DEH-1300R/X1M/EW CXB6148 CXB6147 CAC5929 CAC5789 CNS6383 CNS6114 CWM7306 CWM7305 CXB7184 CXB7183 CXB6658 CNS6385 CXB6657 CNS6345
DEH-1330R,1300R,1310
2.3 EXTERIOR(DEH-1310/X1M/EE)
DEH-1330R,1300R,1310
CDE6470 CEK1136 CD Mechanism Module(S8.1) CXK5203 Holder CNC5704 Cover CNC9127 Cushion Insulator Insulator Tuner Amp Unit Screw Screw Screw FM/AM Tuner Unit Holder Pin Jack(CN301) Terminal(CN403) Plug(CN901) Connector(CN601) Connector(CN605) Antenna Jack(CN402) Holder Holder Holder Heat Sink Case Unit Chassis Unit Detach Grille Assy Screw Button(DETACH) Button(+/-, EQ, LD) CNM5210 CNM6224 CNM6386 CWM7295 ASZ26P080FMC BPZ26P080FMC BSZ26P160FMC CWE1566 CNC8815 CKB1041 CKF1059 CKM1330 CKS3581 CKS3838 CKX1056 CNC8041 CNC8043 CNC9128 CNR1589 CXB4033 CXB4625 CXB6149 BPZ20P100FZK CAC5789 CAC6821
DEH-1330R,1300R,1310
10
DEH-1330R,1300R,1310
CBH2079 CBH2117 CBH2314 CBH2110 CBH2282 CBH2318 CBH2324 CBH2118 CBH2161 CBH2163 CBH2189 CBH2377 CBH2260 CBH2262 CNC8568 CBL1369 CDE5531 CDE5532 CLA3894 CBA1458 CNC8565 CNC8749 CNC9265 CNC8663 CNC8567 CNM3315 CNM6659
CNV5751 CNV6013 CNV5813 CXB2190 CXB5892 CXB4797 CXB4728 CXB5753 CXB2195 CXB4730 CXB4731 CXB2562 CXB4732 CXB4795 JFZ20P025FMC JGZ17P025FZK YE20FUC CXX1285 IMS26P030FMC CNX2982 CPT230SX-TU CNV6175 CNV6014 CBH2315
11
DEH-1330R,1300R,1310
Q472
Q475
Q476
LDET
AMRF ATT
TMUTE
ANT ADJ
FMANT 27 RFGND 26
COMP LDET
21 18
IC 701 PM4009A
11 12
X702
IC 3 EEPROM
FMLOCL SDBW DGND FMSD DI/DO NL1 NL2 4 CE2 CE1 STIND 1 PDIO CN701
NC
CK
LOCH 23 25
LOCL
PDIO
PCE2
PCK
PCE1
SL
LOCL
VCC
VDD
PICKUP UNIT(SERVICE)(P8)
LD MD
LD+ MD
CONTROL UNIT
Q101
98 LD L_OUT 16 CN605 CDL
CN101 14 5
SD
Q411
7 17 20 22 10 19 14
24
11 12 15 16
SL 13
RF ADJ
CREQ
VDD VCC
17
97
PD
IC 201 UPD63711GC
IC 301 BA5985FM
16
TD/FD SD/MD 39
CD DRIVER
FOP 18 TOP
HOME
4
SPINDLE MOTOR
M
CN801
12 11
SOP SOM
S801 HOME
CARRIAGE MOTOR
1 2
14
LOADING MOTOR
3 4 CN802 3 1
1 28 21
6 5 11
19 20 14
22 23 21 24
3 2 4 1
SELECT SENSE
2
Q981
VD B.U
DISC SENSE
+5V REGULATOR
VDD 4
PHOTO UNIT(S8)
IC 701 BA05SFP
1
IN
Q982
CD5VON 7 18 CD5VON VDCONT
12 1 2 3 4
DEH-1330R,1300R,1310
A
66 61 TMUTE LDET CN301
REAR L CH
21
Q346
FM/AM
SD SL
14 13 48 12 PDIO 11 57
Q363
CN901
Q903
VDD B.U B.U
B
GND
BACK UP
IN2_L
POWER AMP
23 FL FL+ RL RL+ 9 11 10 12
E.VOL FIE/EQ
IN3_L
Frontout_L Rearout_L
10 11
14
FL
IC 301 PML003AM
12 RL
IC 302 TDA7386
21 3 5
FL FL+ RL RL+
MUTE 22
STBY 4
Q350
ASENS
63
SYSPW
Q901
64 TELIN CELLULAR MUTE 7 CELLULAR MUTE
BSENS
POWER SWITCH
42 B.U SYSPW 5 6 1 B.REM 5
C
B.REM
IC970 TPD1018F
80 79 27
MUTE
44
KEYBOARD UNIT
RR FR FL RL RR + FR + FL + RL +
CN601
CN1801
BACK UP B. REM
GND ACC
KYDT VDCONT DPDT 8 9 3 4 1 VDD 5 41 5 56 VDD 3 4 20 18 KYDT DPDT
22
LCD
RESET
60
VDD
10 VLCD
SWVDD 35 CD5VON
Q650
22 X1801
23
13 5 6 7 8
DEH-1330R,1300R,1310
A-a
A
A-a A-b
CN402
A-a A-b
Guide page
A-a
A-b
Detailed page
162
DSP-201M-S00B
123
CN403
162
123
272
272
4.194MHz
473
PE5195A
SYSTEM CONTROLLER
CN601
B
KEYBOARD UNIT
D
NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms *Capacitors Code Practical value 103 0.01F 101/10 100F/10V
14
A
1
DEH-1330R,1300R,1310
A-b
FM(100%):+6.6dBs AM(30%):-2.9dBs CD:+10.2dBs E.VOL FIE/EQ
CN301
A
CD:+9.4dBs
332/16
POWER AMP
CN901
NC
B
TDA7386
>
CEK1136
600H
RESET
331/16
A.SENS
B.SENS
CN605
CONTROL UNIT
CD:+4.1dBs
BACK UP
B. REM
GND ACC
RR FR FL RL -
RR + FR + FL + RL +
15
D A C
16
A-a A-b
DEH-1330R,1300R,1310
123
DSP-201M-S00B
CN403
123
272
272
A-a
FM/AM TUNER UNIT
FM(100%):-15.5dBs AM(30%):-26dBs
162 162
CN402
1
4
4.194MHz
RESE
473
NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms *Capacitors Code Practical value 103 0.01F 101/10 100F/10V
C
A-a A-b
B C A
For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes:
CONTROL UNIT
PE5195A
SYSTEM CONTROLLER
6
CN601
B
7
KEYBOARD UNIT
DEH-1330R,1300R,1310
A-a
17
D A C
18
A-a A-b
DEH-1330R,1300R,1310
NC
POWER AMP
1
4 FM(100%):+32.6dBs AM(30%):+23.1dBs CD:+36.2dBs
TDA7386
332/16
A-b
FM(100%):+6.6dBs AM(30%):-2.9dBs CD:+10.2dBs CD:+9.4dBs
CN301 CN901
>
CEK1136
600H
E.VOL FIE/EQ
CEK1136
600H
331/16
RESET
CONTROL UNIT
6
B. REM
GND ACC
CN605
7 C
RR FR FL RL -
RR + FR + FL + RL +
DEH-1330R,1300R,1310
A-b
B
19 A
A-a A-b
DEH-1330R,1300R,1310
A
A
CN402
A-a
FM(100%):-15.5dBs AM(30%):-26dBs
162
DSP-201M-S00B
123
CN403
162
363
153
123
272
272
PE5196A
SYSTEM CONTROLLER
CN601
B
KEYBOARD UNIT
D
NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms *Capacitors Code Practical value 103 0.01F 101/10 100F/10V
20
A
1
DEH-1330R,1300R,1310
A-b
FM(100%):+6.6dBs AM(30%):-2.9dBs CD:+10.2dBs E.VOL FIE/EQ
CN301
A
CD:+9.4dBs
332/16
POWER AMP
CN901
NC
B
TDA7386
>
CEK1136
600H
RESET
331/16
A.SENS
B.SENS
CN605
CONTROL UNIT
CD:+4.1dBs
21
D A C
22
A-a A-b
DEH-1330R,1300R,1310
123
DSP-201M-S00B
CN403
123
272
272
A-a
FM/AM TUNER UNIT
FM(100%):-15.5dBs AM(30%):-26dBs
162 162
CN402
1
4
RESE
363
153
NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms *Capacitors Code Practical value 103 0.01F 101/10 100F/10V
C
A-a A-b
B C A
For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes:
CONTROL UNIT
PE5196A
SYSTEM CONTROLLER
6
CN601
B
7
KEYBOARD UNIT
DEH-1330R,1300R,1310
A-a
23
D A C
24
A-a A-b
DEH-1330R,1300R,1310
NC
POWER AMP
1
4 FM(100%):+32.6dBs AM(30%):+23.1dBs CD:+36.2dBs
TDA7386
332/16
A-b
FM(100%):+6.6dBs AM(30%):-2.9dBs CD:+10.2dBs CD:+9.4dBs
CN301 CN901
>
CEK1136
600H
E.VOL FIE/EQ
CEK1136
600H
331/16
RESET
CONTROL UNIT
CN605
7 C
DEH-1330R,1300R,1310
A-b
A-a A-b
B A
25
DEH-1330R,1300R,1310
KEYBOARD UNIT
LCD CAW1605
26
B
1
PTY
5
TA EQ BSM
6 R1708, 1710, 1712:181 (DEH-1330R/X1M/EW) R1708, 1710, 1712:151 (DEH-1300R/X1M/EW) (DEH-1310/X1M/EE) IL1801, 1802:CEL1638(14V 40mA) (DEH-1330R/X1M/EW) IL1801, 1802:CEL1651(14V 40mA) (DEH-1300R/X1M/EW) (DEH-1310/X1M/EE) D1701-1708:SML210DT (DEH-1330R/X1M/EW) D1701-1708:SML210PT (DEH-1300R/X1M/EW) (DEH-1310/X1M/EE)
7 C
DEH-1330R,1300R,1310
27
A
B A
CN601
DEH-1330R,1300R,1310
C
PICKUP UNIT (SERVICE)(P8)
CONTROL UNIT
CN101
RF-AMP, SE
CL203IRXTU
CL203IRXTU
PHOTO UNIT(S8)
Q1 CPT230SX-TU Q2 CPT230SX-TU
CN802
SPINDLE MOTOR
M1 CXB2190
LOADING MOTOR
CD DRIVER
M2 CXB2195
CN801
28
C D
1
BA05SFP
5V REGULATOR
3 4
DEH-1330R,1300R,1310
SWITCHES: CONTROL UNIT S801 : HOME SWITCH.....ON-OFF S802 : CLAMP SWITCH....ON-OFF The underlined indicates the switch position.
CN701
CN605
C
8
29
DEH-1330R,1300R,1310
Note:1. The encircled numbers denote measuring pointes in the circuit diagram. 2. Reference voltage REFO:2.5V 1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Test mode: Tracking open 1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Normal mode: The defect part passes 800m
- Waveforms
1 RFI 0.5V/div. 0.5s/div. Normal mode: play
3 CH1: FD 0.5V/div. 0.2s/div. 4 CH2: FO+ 2V/div. Test mode: No disc, Focus close
3 CH1: FD 0.5V/div. 0.2s/div. 5 CH2: FOK 2V/div. Normal mode: Focus close
6 CH1: FE 0.5V/div. 1ms/div. 7 CH2: XSI 2V/div. Normal mode: Focus close
REFO REFO
REFO
8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: 32 tracks jump (FWD)
8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: Single jump (FWD)
8 CH1: TE 0.5V/div. 5ms/div. 9 CH2: TD 0.5V/div. Test mode: 100 tracks jump (FWD)
REFO
REFO
REFO
REFO
REFO
REFO
20ms/div.
3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (12cm)
3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (8cm)
REFO REFO
REFO
REFO
REFO
REFO
30
DEH-1330R,1300R,1310
20ms/div.
8 CH1: TE 0.5V/div. 5ms/div. ! CH2: SD 0.5V/div. TEST mode: 100 Tracks jump(FWD)
0 MD
0.5V/div.
0.1s/div.
REFO
REFO
10ms/div.
@ EFM
1V/div.
5s/div.
8 CH1: TE 1V/div. 2ms/div. # CH2: TEC 1V/div. Test mode: Focus close Tracking open
8 CH1: TE 0.5V/div. 0.2s/div. 6 CH2: FE 0.5V/div. Normal mode: AGC after focus close
$ PLCK
2V/div.
0.5s/div.
% SCKO
2V/div.
1s/div.
REFO
REFO
REFO GND
REFO GND
^ Dout
2V/div.
10s/div.
& LRCK
2V/div.
20s/div.
* VD
5V/div.
50ms/div.
31
DEH-1330R,1300R,1310
( CH1: R OUT 1V/div. 0.2ms/div. ) CH2: L OUT 1V/div. Normal mode: Play (1kHz 0dB)
REFO
REFO
REFO
1 CH1: RFI 1V/div. 0.5ms/div. CH2: HOLD 5V/div. Normal mode: The defect part passes 800m(B.D)
3 CH1: FD 0.5V/div. 0.5ms/div. CH2: HOLD 5V/div. Normal mode: The defect part passes 800m(B.D)
9 CH1: TD 0.1V/div. 0.5ms/div. CH2: HOLD 5V/div. Normal mode: The defect part passes 800m(B.D)
REFO
REFO
REFO
REFO
REFO
REFO
32
DEH-1330R,1300R,1310
33
DEH-1330R,1300R,1310
CORD ASSY
Connector
Capacitor
SIDE A
B
P.C.Board Chip Part
SIDE B
34
A
1
C
2
CN701
3 4
CN1801
DEH-1330R,1300R,1310
SIDE A
ANTENNA PRE OUT
A
3 1 2
FRONT
5 6 7
A
8
35
DEH-1330R,1300R,1310
4 5 6
3 2 1
1 2 3
6 5 4
36
A
1
DEH-1330R,1300R,1310
SIDE B
A
1 2 3
6 5 4
4 5 6
3 2 1
FRONT
5 6 7
A
8
37
D A C
38
DEH-1330R,1300R,1310
1 2 3 4 5 6 PTY
BAND
VOL-
TA
VOL-
SOURCE SOURCE
AUDIO
B
BSM EJECT
KEYBOARD UNIT
EQ
VOL+
VOL+
SIDE A
DEH-1330R,1300R,1310
SIDE B
A
CN601
KEYBOARD UNIT
B
4
39
D A C
40
C
PICKUP UNIT(SERVICE)(P8) M1 CARRIAGE MOTOR M2 LOADING MOTOR
HOME
CONTROL UNIT
DEH-1330R,1300R,1310
C D
M3 SPINDLE MOTOR
PHOTO UNIT(S8)
CN605
SIDE A
3 2 1
C CN802
DEH-1330R,1300R,1310
SIDE B
A
CLAMP
CONTROL UNIT
C
4
41
DEH-1330R,1300R,1310
A
IC IC IC IC IC IC Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q D D D D D D D D D D D D D D D D D
Unit Number : CWM7294 (DEH-1330R/X1M/EW, DEH-1300R/X1M/EW) Unit Name : Tuner Amp Unit
301 302 601 602 701 970 346 350 351 353 411 412 472 474 475 476 477 650 901 902 903 904 905 906 920 951 981 982 650 651 652 653 654 655 901 902 903 904 905 906 907 941 942 951 952 IC IC IC IC IC IC Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode PML003AM TDA7386 PE5195A S-80834ANY PM4009A TPD1018F RN1610 DTA124EK DTC114EK DTA124EK 2SC2412K 2SC2412K RN1610 2SD1757K 2SD1757K 2SC2412K DTA124EK 2SA1037K 2SC2412K 2SC2412K 2SD1859 2SD2396 2SB1243 DTC114EK RN46A1 2SA1037K 2SD2396 RN46A1 1SS270 1SS270 1SS270 1SS270 1SS270 1SS270 HZS7L(C2) S5688G S5688G HZS7L(A1) S5688G HZS6L(B2) HZS9L(B3) S5688G S5688G 1SS270 1SS270
MISCELLANEOUS
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 310 311 330 331 332 333 334 335 342 343 344 345 346 351 352 353 354 360 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 RD1/4PU222J RD1/4PU222J RD1/4PU472J RS1/16S472J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S681J RS1/16S681J RS1/16S223J RS1/16S223J RS1/16S0R0J RS1/16S102J RS1/16S103J RS1/16S103J RS1/16S331J RD1/4PU153J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S103J RS1/16S681J RD1/4PU473J RD1/4PU472J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S681J RS1/16S681J RS1/16S393J RS1/16S681J RS1/16S222J
42
DEH-1330R,1300R,1310
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 428 430 431 440 441 442 443 444 445 446 447 460 461 464 465 474 475 476 477 478 479 611 619 620 622 623 624 625 626 627 628 630 631 649 650 651 652 653 654 655 656 657 658 660 681 682 683 684 713 717 721 722 723 724 901 902 903 904 905 906 907 908 909 910 911
Part No. ------------------------RS1/16S222J RS1/16S474J RS1/16S153J RS1/16S681J RS1/16S102J RS1/16S473J RS1/16S681J RS1/16S472J RS1/16S473J RS1/16S224J RS1/16S0R0J RS1/16S162J RS1/16S162J RS1/16S272J RS1/16S272J RS1/16S222J RS1/16S223J RS1/16S223J RS1/16S222J RS1/16S224J RD1/4PU224J RS1/16S473J RS1/16S0R0J RS1/16S223J RD1/4PU222J RD1/4PU222J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RD1/4PU222J RS1/16S822J RD1/4PU102J RS1/16S222J RD1/4PU222J RD1/4PU222J RS1/16S472J RD1/4PU222J RS1/16S473J RS1/16S103J RS1/16S103J RD1/4PU102J RD1/4PU102J RS1/16S1R0J RD1/4PU681J RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S225J RD1/4PU102J RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S681J RS1/16S104J RD1/4PU104J RD1/4PU103J RS1/16S473J RD1/4PU102J RS1/16S473J RS1/16S473J RS1/16S472J RD1/4PU103J RS1/16S0R0J RS1/16S122J
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R 912 913 914 916 918 944 951 953 954 955 971 981 982 983 984
Part No. ------------------------RD1/4PU103J RS1/16S101J RD1/4PU152J RS1/16S221J RS1/16S1R0J RD1/4PU152J RD1/4PU153J RS1/16S472J RD1/4PU102J RD1/4PU473J RS1/16S103J RS1/16S472J RS1/16S222J RD1/4PU221J RD1/4PU221J
CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 310 311 313 314 315 316 330 331 332 333 334 335 336 337 338 340 341 346 347 348 349 350 352 361 362 363 364 365 366 367 368 369 370 371 372 390 391 411 412 413 414 415 416 417 418 419 420 441 442 462 3300F/16V CKSRYB105K6R3 CKSRYB104K16 CKSRYB105K6R3 CKSRYB104K16 CKSRYB102K50 CKSRYB102K50 CEJA470M10 CEJA100M16 CKSRYB104K16 CEJA4R7M35 CEJA4R7M35 CKSRYB104K16 CKSRYB153K25 CKSRYB153K25 CKSRYB104K16 CEAL2R2M50 CEJA2R2M50 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CEJA330M10 CCSRCH101J50 CEJA2R2M50 CKSQYB225K10 CEJA100M16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB225K10 CKSRYB104K16 CCH1368 CKSRYB223K25 CKSRYB223K25 CKSRYB102K50 CEJA220M10 CKSRYB473K16 CEAL101M10 CKSRYB472K50 CKSRYB472K50 CCSRCH101J50 CCSRCH101J50 CKSRYB182K50 CKSRYB223K25 CKSRYB123K25
43
DEH-1330R,1300R,1310
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 463 466 467 490 493 612 613 614 621 630 631 650 711 712 714 715 718 719 720 725 726 901 902 903 904 905 906 907 941 971 972 981 982 983
Part No. ------------------------CKSRYB123K25 CEJA1R0M50 CEJA1R0M50 CKSQYB103K50 CKSRYB472K50 CEJA4R7M35 CKSRYB473K16 CCSRCH101J50 CCSRCH101J50 CKSRYB473K16 CEAL2R2M50 CKSRYB104K16 CEAL220M6R3 CKSRYB104K16 CKSRYB471K50 CKSRYB104K16 CKSRYB471K50 CEAL220M6R3 CKSRYB104K16 CCSRCH270J50 CCSRCH270J50 CEJA101M10 CKSRYB473K16 CCH1331 CKSRYB473K16 CCH1326 CKSRYB103K50 CEJA101M16 CKSRYB473K16 CKSRYB103K50 CKSRYB473K16 CEJA101M10 CKSRYB102K50 CKSRYB473K16
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------D D D D D D D D D D D D D D L L L L L L L L L X AR 654 655 901 902 903 904 905 906 907 941 942 951 952 981 310 401 402 403 610 611 650 901 951 610 946 Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Ferri-Inductor Ferri-Inductor Ferri-Inductor Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor Choke Coil 600H Ferri-Inductor Crystal Resonator 4.194304MHz Arrester FM/AM Tuner Unit
Part No. ------------------------1SS270 1SS270 HZS7L(C2) S5688G S5688G HZS7L(A1) S5688G HZS6L(B2) HZS9L(B3) S5688G S5688G 1SS270 1SS270 HZS9L(B1) LAU1R0M LAU4R7K LAU2R2K LAU100K LAU101K LAU2R2K LAU2R2K CTH1221 LAU2R2K CSS1023 DSP-201M-S00B CWE1566
470F/16V 330F/16V
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 310 311 332 333 334 335 342 343 344 345 346 351 352 353 354 360 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 427 428 460 461 464 465 468 469 610 RD1/4PU222J RD1/4PU222J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S681J RS1/16S681J RS1/16S223J RS1/16S223J RS1/16S0R0J RS1/16S102J RS1/16S103J RS1/16S103J RS1/16S331J RD1/4PU153J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S103J RS1/16S681J RD1/4PU473J RD1/4PU472J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S681J RS1/16S681J RS1/16S393J RS1/16S222J RS1/16S222J RS1/16S162J RS1/16S162J RS1/16S272J RS1/16S272J RS1/16S0R0J RS1/16S0R0J RD1/4PU153J
A
IC IC IC IC IC Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q D D D D
MISCELLANEOUS
44
DEH-1330R,1300R,1310
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 611 619 620 622 623 624 625 626 627 628 629 630 631 649 650 651 652 653 654 655 656 657 658 660 681 682 683 684 901 902 903 904 905 906 907 908 909 910 911 912 913 914 916 918 944 951 953 954 955 971 981 982 983 984
Part No. ------------------------RS1/16S363J RS1/16S0R0J RS1/16S223J RD1/4PU222J RD1/4PU222J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RD1/4PU222J RS1/16S473J RS1/16S822J RD1/4PU102J RS1/16S222J RD1/4PU222J RD1/4PU222J RS1/16S472J RD1/4PU222J RS1/16S473J RS1/16S103J RS1/16S103J RD1/4PU102J RD1/4PU102J RS1/16S1R0J RD1/4PU681J RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S104J RD1/4PU104J RD1/4PU103J RS1/16S473J RD1/4PU102J RS1/16S473J RS1/16S473J RS1/16S472J RD1/4PU103J RS1/16S0R0J RS1/16S122J RD1/4PU103J RS1/16S101J RD1/4PU152J RS1/16S221J RS1/16S1R0J RD1/4PU152J RD1/4PU153J RS1/16S472J RD1/4PU102J RD1/4PU473J RS1/16S103J RS1/16S472J RS1/16S222J RD1/4PU221J RD1/4PU221J
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 334 336 337 340 341 346 347 348 349 350 361 362 363 364 365 366 367 368 369 370 371 372 390 391 411 412 413 414 415 416 417 419 462 463 490 612 613 614 628 629 630 631 650 901 902 903 904 905 906 907 941 971 972 981 982 983 470F/16V 330F/16V
Part No. ------------------------CEJA4R7M35 CKSRYB153K25 CKSRYB153K25 CEAL2R2M50 CEJA2R2M50 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CEJA330M10 CEJA2R2M50 CKSQYB225K10 CEJA100M16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB225K10 CKSRYB104K16 CCH1368 CKSRYB223K25 CKSRYB223K25 CKSRYB102K50 CEJA220M10 CKSRYB473K16 CEAL101M10 CKSRYB472K50 CCSRCH101J50 CKSRYB123K25 CKSRYB123K25 CKSQYB103K50 CEJA4R7M35 CKSRYB473K16 CCSRCH101J50 CCSRCH150J50 CCSRCH150J50 CKSRYB473K16 CEAL2R2M50 CKSRYB104K16 CEJA101M10 CKSRYB473K16 CCH1331 CKSRYB473K16 CCH1326 CKSRYB103K50 CEJA101M16 CKSRYB473K16 CKSRYB103K50 CKSRYB473K16 CEJA101M10 CKSRYB102K50 CKSRYB473K16
3300F/16V
CAPACITORS
C C C C C C C C C C 310 311 313 314 315 316 330 331 332 333 CKSRYB105K6R3 CKSRYB104K16 CKSRYB105K6R3 CKSRYB104K16 CKSRYB102K50 CKSRYB102K50 CEJA470M10 CEJA100M16 CKSRYB104K16 CEJA4R7M35
B
IC D D D D
MISCELLANEOUS
1801 1701 1702 1703 1704
45
DEH-1330R,1300R,1310
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------D D D D D D D D X IL IL 1705 1706 1707 1708 1801 1802 1811 1812 1801 1801 1802 LED LED LED LED Diode Diode LED LED Ceramic Resonator 4.97MHz Lamp 14V 40mA Lamp 14V 40mA LCD
Part No. ------------------------SML210DT SML210DT SML210DT SML210DT MA152WK MA152WA NSSW440-9159 NSSW440-9159 CSS1422 CEL1638 CEL1638 CAW1632
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R 1706 1707 1708 1709 1710 1711 1712 1713 1801 1802 1803 1804 1805 1806
Part No. ------------------------RS1/16S151J RS1/16S151J RS1/16S151J RS1/16S181J RS1/16S151J RS1/16S181J RS1/16S151J RS1/16S131J RS1/16S222J RS1/16S222J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J
RESISTORS
R R R R R R R R R R R R R R R R R R R 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1801 1802 1803 1804 1805 1806 RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S151J RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S131J RS1/16S222J RS1/16S222J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J
CAPACITORS
C C C 1801 1811 1812 CKSRYB103K50 CKSQYF104Z25 CKSQYF104Z25
B
IC D D D D D D D D D D D D X IL IL
MISCELLANEOUS
1801 1701 1702 1703 1704 1705 1706 1707 1708 1801 1802 1811 1812 1801 1801 1802
CAPACITORS
C C C 1801 1811 1812 CKSRYB103K50 CKSQYF104Z25 CKSQYF104Z25
B
IC D D D D D D D D D D D D X IL IL
MISCELLANEOUS
1801 1701 1702 1703 1704 1705 1706 1707 1708 1801 1802 1811 1812 1801 1801 1802
RESISTORS
R R R R R R R R R R R R R R R R R R R 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1801 1802 1803 1804 1805 1806 RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S151J RS1/16S151J RS1/16S151J RS1/16S181J RS1/16S151J RS1/16S181J RS1/16S151J RS1/16S131J RS1/16S222J RS1/16S222J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J
RESISTORS
R R R R R 1701 1702 1703 1704 1705 RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J
CAPACITORS
C C C 1801 1811 1812 CKSRYB103K50 CKSQYF104Z25 CKSQYF104Z25
46
DEH-1330R,1300R,1310
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C 220 221 222 223 224 301 603 604 702 703
Part No. ------------------------CCSRCH510J50 CKSRYB682K25 CEV220M6R3 CKSRYB103K25 CKSRYB224K10 CEV101M10 CCSQSL152J50 CCSQSL152J50 CCH1349 CKSQYB334K16
C
IC IC IC Q D D X S S
MISCELLANEOUS
201 301 701 101 801 802 201 801 802 IC IC IC Transistor LED LED Ceramic Oscillator 16.934MHz Spring Switch(HOME) Spring Switch(CLAMP) UPD63711GC BA5985FM BA05SFP 2SB1132 CL203IRXTU CL203IRXTU CSS1456 CSN1051 CSN1052
C C C C C
10F/10V
D
Q Q
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R 101 102 103 201 202 203 204 205 206 207 302 303 501 502 601 602 605 606 801 803 902 906 RS1/8S120J RS1/8S100J RS1/16S222J RS1/16S104J RS1/16S103J RS1/16S393J RS1/16S103J RS1/16S103J RS1/16S182J RS1/16S123J RS1/16S153J RS1/16S103J RS1/16S102J RA4C681J RS1/16S102J RS1/16S102J RS1/16S0R0J RS1/16S0R0J RS1/8S751J RS1/8S751J RS1/16S0R0J RS1/16S0R0J
CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C 101 102 103 104 105 106 107 201 202 203 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 CKSRYB102K50 CKSRYB104K16 CEV101M6R3 CEV470M6R3 CKSQYB334K16 CKSQYB334K16 CKSQYB334K16 CKSRYB104K16 CKSRYB471K50 CKSRYB104K16 CEV101M6R3 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB332K50 CKSRYB104K16 CKSRYB104K16 CKSRYB392K50 CKSRYB104K16 CKSRYB104K16 CCSRCJ3R0C50 CCSRCH270J50 CKSRYB104K16 CCSRCH181J50
47
DEH-1330R,1300R,1310
6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions This unit uses a single power supply (+5V) for the regulator. The signal reference potential, therefore, is connected to REFO(approx. 2.5V) instead of GND. If REFO and GND are connected to each other by mistake during adjustments, not only will it be impossible to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. To avoid this, take special note of the following. Do not connect the negative probe of the measuring equipment to REFO and GND together. It is especially important not to connect the channel 1 negative probe of the oscilloscope to REFO with the channel 2 negative probe connected to GND. Since the frame of the measuring instrument is usually at the same potential as the negative probe, change the frame of the measuring instrument to floating status. If by accident REFO comes in contact with GND, immediately switch the regulator or power OFF. Always make sure the regulator is OFF when connecting and disconnecting the various filters and wiring required for measurements. Before proceeding to further adjustments and measurements after switching regulator ON, let the player run for about one minute to allow the circuits to stabilize. Since the protective systems in the unit's software are rendered inoperative in test mode, be very careful to avoid mechanical and /or electrical shocks to the system when making adjustment. Disc detection during loading and eject operations is performed by means of a photo transistor in this unit.Consequently, if the inside of the unit is exposed to a strong light source when the outer casing is removed for repairs or adjustment, the following malfunctions may occur. *During PLAY, even if the eject button is pressed,the disc will not be ejected and the unit will remain in the PLAY mode. *The unit will not load a disc. When the unit malfunctions this way, either re-position the light source, move the unit or cover the photo transistor. 2) Test Mode This mode is used for adjusting the CD mechanism module of the device. Test mode starting procedure Reset while pressing the 4 and 6 keys together. Test mode cancellation Switch ACC, back-up OFF. After pressing the EJECT key, do not press any other key until the disk is completely ejected. If the ] or [ key is pressed while focus search is in progress, immediately turn the power off (otherwise the actuator may be damaged due to adhesion of the lenses). Jump operation of TRs other than 100TR continues after releasing the key. CRG move and 100TR jump operations are brought into the Tracking close status when the key is released. Powering Off/On resets the jump mode to 1TR, and the automatic adjustment value to the initial value.
48
DEH-1330R,1300R,1310
- Flow Chart
4
Test Mode In Reset
Select CD
SOURCE
New test mode
BAND
Power ON (Adjustment for T.Offset)
TRK MIN SEC
Display
00 00 00
99 99 99
BAND
Focus Close/ S Curve Check
TRK MIN SEC
3 *1
Focus Mode Select
6 *2
2 *3
CRG+
MIN SEC
TRK
MIN
Display
91 91 91
Display
0x 0x 0x
00 00 00
or
TRK MIN SEC
00 00 00
or
TRK MIN SEC
00 00 00
or
TRK MIN SEC
99 99 99
Power OFF
99 99 99
99 99 99
BAND
T.Close and F,T AGC and RF AGC and Fit Servo
CRG+
MIN SEC
T.Balance Adjustment
Display
8x 8x 8x
or
TRK MIN SEC
8x 8x 8x
or
TRK MIN SEC
9x 9x 9x
Power OFF
9x 9x 9x
Tracking Open
BAND
1 *4
F, T, RF AGC/ F.Bias Display Select
6 *5
*6 CRG-/TR Jump- *6
CRG+/TR Jump+
*7
TRK MIN SEC
Power OFF
Display
8x 8x 8x
or
TRK MIN SEC
BAND
Tracking Open
TRK MIN
9x 9x 9x
SEC
Display
8x 8x 8x
or
TRK MIN SEC
9x 9x 9x
*1 *2 "00", "99"Focus Close / "01"S.Curve Focus Close 00(99) S.Curve 01 LD Off 02 *6 *7 1TR/4TR/10TR/32TR/100TR CRG Move,100TR Jump
*3 *4
F.Cancel
T.Offset
F.AGC Gain
T.AGC Gain
F.Bias
*5
1TR 91(81)
4TR 92(82)
10TR 93(83)
32TR 94(84)
100TR 95(85)
49
DEH-1330R,1300R,1310
Purpose : To check that the grating is within an acceptable range when the PU unit is changed. Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. Method : Measuring Equipment Measuring Points Disc Mode
CONTROL UNIT
E F
E REFO
Oscilloscope
REFO
REFO
Checking Procedure 1. In test mode, load the disc and switch the 5V regulator on. 2. Using the ] and [ buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 . Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the mechanism should be judged to be at fault. Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble".
50
DEH-1330R,1300R,1310
Grating waveform
45
60
75
90
51
DEH-1330R,1300R,1310
7. GENERAL INFORMATION
7.1 DIAGNOSIS 7.1.1 TEST MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing. (1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before. 2) Head unit display examples Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. 8-digit display ERRORxx 6-digit display ERRxx OR Errxx 4-digit display Exx
(2) Error Code List Code Class Displayed error code Description of the code and potential cause(s) 10 Electricity Carriage Home NG CRG can't be moved to inner diameter. CRG can't be moved from inner diameter. Failure on home switch or CRG move mechanism. 11 12 Electricity Electricity Focus Servo NG Spindle Lock NG Subcode NG Focusing not available. Stains on rear side of disc or excessive vibrations on REWRITABLE. Spindle not locked. Sub-code is strange (not readable). Failure on spindle, stains or damages on disc, or excessive vibrations. A disc not containing CD-R data is found. Turned over disc are found, though rarely. Failure on home switch or CRG move mechanism. An appropriate RF AMP gain can't be determined. CD signal error. APC protection doesn't work. Focus can be easily lost. Damages or stains on disc, or excessive vibrations. Failed to reach target address. CRG tracking error or damages on disc. Power (VD) is ground faulted. Failure on SW transistor or power supply (failure on connector).
RF AMP NG 17 30 A0 Electricity Electricity System Setup NG Search Time Out Power Supply NG
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. A newly designed head unit must conform to the example given above. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.
52
DEH-1330R,1300R,1310
To power on (offset adjustment not performed) 6 Mode switching Auto/Manu /T.Close (no AGC)/Jump switching Note: Eject and CD on/off is performed in the same procedure as that for the normal mode. (3) Cause of Error and Error Code Code Class Contents 40 Electricity Off focus detected. 41 42 43 Electricity Electricity Electricity Spindle unlocked. Sub-code unreadable. Sound skipping detected.
Description and cause FOK goes low. Damages/stains on disc, vibrations or failure on servo. FOK = Low continued for 50 msec. Damages/stains on disc, vibrations or failure on servo. Sub-code was unreadable for 50 msec. Damages/stains on disc, vibrations or failure on servo. Last address memory function was activated. Damages/stains on disc, vibrations or failure on servo.
Note: Mechanical errors during aging are not displayed. The error codes should be indicated in the same way as in the normal mode.
53
DEH-1330R,1300R,1310
(4) Display of Operational Status (CPOINT) during Setup Status No. Contents 01 Carriage move to home position started. 02 Carriage is moving toward inner diameter. 03 05 11 12 13 14 15 16 17 18 24 25 26 27 28 29 30 31 32 33 34 35 36 Carriage is moving toward outer diameter. Carriage outer diameter feed (1 second) in progress. Setup started. Spindle rotation and focus search started. Waiting for focus close (XSI=Low). Waiting for focus close (FOK=High). (After AGC) Waiting for focus close (FOK=High). (Before AGC) Rough AGC in progress. Setup (1/2) before T balance adjustment is started. Setup (2/2) before T balance adjustment is started. T balance adjustment (1/2). T balance adjustment (2/2). Standing by after spindle rough servo is over. Setup before RF AGC (first) is started. RF AGC (first) in progress. Setup before RF AGC (second) is started. RF AGC (second) in progress. Tracking close in progress. Standing by after tracking is closed. Focus AGC started. Focus AGC in progress. Tracking AGC started. Tracking AGC in progress. Spindle processes applicable servo. Check of MIRR and LOCK pin. RF AGC in progress. CRG close in progress. Check of sub-code.
Protective action None Specified 10 seconds has been passed or failure on home switch. Specified 10 seconds has been passed or failure on home switch. None None None Specified focus search time has been passed. Specified focus search time has been passed. Specified focus search time has been passed. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Spindle not locked. Sub-code unreadable.
(5) Display Examples 1) During Setup (When status no. = 11) TRK No. MIN. SEC. 11 11' 11" 2) During Operation (TOC read, TRK search, Play, FF and REV) The same as in the normal mode. 3) When a Protection Error Occurred Switch to the following displays (A) and (B) using the [BAND] switch: (A) Error occurrence timing display in absolute time. An example: Error occurred in 12th tune at 34'56" in absolute time. TRK No. 12 MIN. 34' SEC. 56"
(B) Error No. display An example: Error #40 (Off focus is detected) ERROR-40
54
DEH-1330R,1300R,1310
7.1.2 DISASSEMBLY
- Removing the Case Unit (not shown)
1. Remove the Case Unit.
CD Mechanism Module
Fig.1
Cover
Fig.2
Straight the tabs at fore locations indicated and then remove the Tuner Amp Unit. (Fig.3)
55
DEH-1330R,1300R,1310
A Upper Frame
Arm
Arm B A
56
DEH-1330R,1300R,1310
B Pin
Short Pin
Spindle Motor
Control Unit
57
DEH-1330R,1300R,1310
C Guide
Belt
A Loading Motor
Pickup Unit
Shaft
58
DEH-1330R,1300R,1310
PRE OUT
ANTENNA
15 13 11 9 7 5 3 1 16 14 12 10 8 6 4 2
1. BACK UP 2. GND 3. NC 4. ACC 5. B.REM 6. NC 7. TEL MUTE 8. NC 9. FL10. RL11. FL+ 12. RL+ 13. FR14. RR15. FR+ 16. RR+
59
DEH-1330R,1300R,1310
60
DEH-1330R,1300R,1310
Pin No. 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin Name RDT reset LDET RCK asens bsens dsens TMUTE NC VDD X2 X1 IC(VPP) NC TESTIN AVDD AVREF0 SL TEMP VDSENS DINC EJTD
I/O I I I I I I O
Format
I I I I I
Function and Operation RDS data input Reset PLL lock detection input RDS clock input ACC power sense input Back up power sense input Grille detach sense input Tuner mute output Not used VDD Crystal oscillator connection pin Crystal oscillator connection pin IC(VPP) Not used Test program mode input AVDD AVREF0 Signal level input Temperature detection input VD power supply sense input Disc detection input Disc eject position detect input IC's marked by* are MOS type. Be careful in handing them because they are very liable to be damaged by electrostatic induction.
61 60
S-80834ANY
20 21 40
41
1
OUT
2
VDD
3
VSS
61
DEH-1330R,1300R,1310
I O O O
*PD6340A
33
32
48 49 64 1
17 16
62
DEH-1330R,1300R,1310
O I O O O O O I O
O O I O I O I O O O O I O O O O O O O O O O O I I I
63
DEH-1330R,1300R,1310
Pin Name TEST0 TEST1 ATEST A.GND FD TD SD MD DAC0 DAC1 DAC2 DAC3 A.VDD EFM ASY C3T RFI AGCO AGCI RFO EQ2 EQ1 RFA.GND A C B D F E A.VDD REFOUT FEFEO TETEO TE2 TEC A.GND PD LD PN A.VDD
I/O I I O O O O O O O O O O I I O I O
I I I I I I I O I O I O O I I O I
Function and Operation Test pin Test pin Test pin Analog circuit GND Focus drive output Tracking drive output Sled drive output Spindle drive output DAC output for adjustment DAC output for adjustment DAC output for adjustment DAC output for adjustment Positive power supply terminal to analog circuit EFM signal output EFM comparator reference voltage input 3T detection capacitor additional pin RF signal input for EFM data regulation RF signal output of after gain adjustment RF-AGC amplifier input RF summing amplifier output RF amplifier equalizer parts additional pin RF amplifier equalizer parts additional pin RF summing amplifier inverted input Analog circuit GND Photo detector A input Photo detector C input Photo detector B input Photo detector D input Photo detector F input Photo detector E input Positive power supply terminal to analog circuit Reference electric potential output Focus error amplifier inverted input Focus error amplifier output Tracking error amplifier inverted input Tracking error amplifier output Tracking error output of after amplification Tracking comparator input Analog circuit GND PD detection signal input for LD output monitor LD control current output APC circuit control polarity set pin Positive power supply terminal to analog circuit
1 1 100 80 76 61 75 60
50 40 51 41
64
DEH-1330R,1300R,1310
ATT
ANT ADJ
FMANT
COMP LDET
21 18
27 RFGND 26
IC 3 EEPROM
FMLOCL SDBW DGND FMSD DI/DO NL1 NL2 4 CE2 CE1 STIND 1
NC
CK
LOCH 23 25
LOCL
7 17 20 22 10 19 14
24
11 12 15 16
SL 13
RF ADJ
CREQ
VDD VCC
No. Symbol I/O Explain 1 STIND O stereo indicator 2 FMSD O FM station detector
"Low" when the FM stereo signals are received. To be pulled up to the "VDD" at 47k. "High" when signals are received. To be pulled up to the "VDD" at 47k Meanwhile, 10k should be used when taking diver FIX trigger from here and "High: 0.9VDD or more" and "Low: 250mV or less". (Should satisfy the diver IC specifications) 3 NL1 O noise level-1 "High" when noise is received. Output for the RDS. GND at 47k //1,800pF. 4 NL2 O noise level-2 "High" when noise is received. Output for the RDS. GND at 36k //330pF. 5 Rch O R channel FM stereo "R-ch" signal output or AM audio output. output Add the specified di-emphasis constant. 6 Lch O L channel FM stereo "L-ch" signal output or AM audio output. output Add the specified di-emphasis constant. 7 WC write control EEPROM write control. Writing permissible at "Low". Normally open. 8 SDBW O SD bandwidth SD bandwidth signal output. For detection of detuning data for the RDS. 9 NC Not used 10 VDD power Power supply pin for the digital section. supply D.C. 5V +/- 0.25V. Be careful about overlapping noise in the logic section. 11 DGND digital ground Grounding for the digital section. 12 CE2 I chip enable-2 EEPROM chip enable. Active a "Low" To be pulled up to the "VDD" at 47k 13 SL I/O signal level Received FM/AM signal level (strength) output. Connect the specified load resistor and capacitor (10k + 39k //4,700pF) 14 DI/DO I/O data input/ Data input/Data output data output To be pulled up to the "VDD" at 47k 15 CK I clock Clock input To be pulled up to the "VDD" at 47k 16 CE1 I chip enable-1 AFRF chip enable. Active at "High" To be grounded at 47k 17 NC Not used 18 LDET O lock detector Active at "Low". To be pulled up to the "VDD" at 47k 19 CREQ I current request Active at "Low". To be grounded at 47k 20 NC Not used 21 COMP O composite signal FM composite signal output. r out < 100 22 VCC power supply Analog section power supply pin.D.C.8.4V +/- 0.3V 23 LOCH I local high FM local high pin. When seeking local high, apply 5V together with "LOCL". 24 FMLOCL I FM local low FM local low pin. When seeking local low, apply 5V to the base of the NPN transistor with which the specified resistor is being connected to the emitter. Keep it open in case of ordinary marketed models. 25 LOCL I local low FM/AM local low pin. When seeking local low, apply 5V to the base of the NPN transistor. Since this pin is exclusive for AM when the FMLOCL is in use, do not drive it under FM. 26 RFGND RF ground Grounding for the antenna section. 27 FMANT I FM antenna input FM antenna input. 75. Serge absorber (DSP-201M-S00B) is necessary. 28 AMANT I AM antenna input AM antenna input. High impedance. Connect to the antenna through an L (LAU type) of 4.7H.To cope with the power transmission line hums, insert a series circuit consisting of an L (a coil of about 100mH) + R (a resistor of 470 to 2.2k) between the GND.
65
COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B
COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B SEG39 SEG38 SEG37 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 NC NC SEG36
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
DEH-1330R,1300R,1310
66
- CAW1632(DEH-1330R/X1M/EW, DEH-1300R/X1M/EW)
7.2.2 DISPLAY
COMMON
SEGMENT
- CAW1633(DEH-1310/X1M/EE)
DEH-1330R,1300R,1310
67
COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B SEG39 SEG38 SEG37 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 NC NC SEG36 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
COMMON
SEGMENT
DEH-1330R,1300R,1310
VDD=5V 68pin
bsens 64pin BSENS=L asens 63pin ASENS=L dsens 65pin DSENS=L ADPWH 20pin
Starts communication with Grille microcomputer. 300ms SWVDDL 41pin Source keys operative
300ms In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300msec, the oscillator may be defective.
Source ON
SYSPWH 42pin
68
DEH-1330R,1300R,1310
Key Finder
Head Unit (DEH-1330R,1300R)
+/ buttons
LOCAL/BSM button
EQ button
CD loading slot
EJECT button
+/ buttons
LOCAL/BSM button
EQ button
CD loading slot
EJECT button
DEH-1330R,1300R,1310
70
Basic Operation
Basic Operation of Tuner
This products AF function can be switched ON and OFF. AF should be switched OFF for normal tuning operations.
To Listen to Music
The following explains the initial operations required before you can listen to music.
Note:
1. Select the desired source (e.g. Tuner). Manual and Seek Tuning
You can select the tuning method by changing the length of time you press the 2/3 button.
Manual Tuning (step by step) Seek Tuning 0.5 seconds or less 0.5 seconds or more
Each press of the SOURCE button selects the desired source in the following order: Built-in CD player = Tuner Note:
Note:
When no disc is set in this product, built-in CD player source will not change. When this products blue/white lead is connected to the cars Auto-antenna relay control terminal, the cars Auto-antenna extends when this products source is switched ON. To retract the antenna, switch the source OFF.
If you continue pressing the button for longer than 0.5 seconds, you can skip broadcast stations. Seek Tuning starts as soon as you release the button. Stereo indicator lights when a stereo station is selected.
Preset Tuning You can memorize broadcast stations in buttons 1 through 6 for easy, one-touch station recall.
Preset station recall Broadcast station preset memory 2 seconds or less 2 seconds or more
Band
F1 (FM1) = F2 (FM2) = MW/LW
Note:
Up to 12 FM stations (6 in F1 (FM1) and F2 (FM2)) and 6 MW/LW stations can be stored in memory. You can also use the 5 or buttons to recall broadcast stations memorized in buttons 1 through 6.
Basic Operation
CD Loading Slot
Note:
The built-in CD player plays one standard 12 cm or 8 cm (single) CD at a time. Do not use an adapter when playing 8 cm CD. Dont insert any materials except for CD into CD loading slot.
You can select between Track Search or Fast Forward/Reverse by pressing the 2/3 button for a different length of time.
0.5 seconds or less Continue pressing
Track Search
Fast Forward/Reverse
Note:
If a disc cannot be inserted fully or playback fails, make sure the recorded side is down. Push the EJECT button and check the disc for damage before reinserting it. If a disc is inserted with the recorded side up, it will be ejected automatically after a few moments. If the built-in CD player cannot operate properly, an error message (such as ERROR-14) appears on the display. Refer to Built-in CD Players Error Message.
DEH-1330R,1300R,1310
71
DEH-1330R,1300R,1310
72
1. This product 2. Rear output 4. Fuse 3. Antenna jack 17. Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. 15. Connecting cords with RCA pin plugs (sold separately). 16. Power amp (sold separately) 6. Connect leads of the same color to each other. 18. Blue/white To system control terminal of the power amp (max. 300 mA 12 V DC). 19. System remote control 20.Rear speaker (Left) + 21.Rear speaker (Right) + 22. Perform these connections when using a different amp (sold separately). 23. Blue/white (6*) 24. Blue/white (7*) To Auto-antenna relay control terminal (max. 300 mA 12 V DC). 14.Speaker leads White : Front left + White/black : Front left Gray : Front right + Gray/black : Front right Green : Rear left + Green/black : Rear left Violet : Rear right + Violet/black : Rear right 25. The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*.
5. Note: Depending on the kind of vehicle, the functio of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*.
1*
3*
2*
5*
4*
7. Cap (1*) When not using this terminal, do not remove the cap.
8. Yellow (3*) 9. Yellow (2*) Back-up To terminal always supplied (or accessory) with power regardless of ignition switch position.
11. Red (4*) To electric terminal controlled by ignition switch (12 V DC) ON/OFF.
13.ISO connector Note: In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors.
Rear output Power amp (sold separately) Connecting cords with RCA pin plugs (sold separately)
Antenna jack
Fuse
Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC) .
Yellow To terminal always supplied with power regardless of ignition switch position. Gray + Front speaker Left + Rear speaker Green/black Violet/black Green Violet + Rear speaker White/black Gray/black Right
+ Front speaker
Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. White
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
+ Rear speaker
+ Rear speaker
DEH-1330R,1300R,1310
73
DEH-1330R,1300R,1310
8.2 SPECIFICATIONS
- DEH-1330R,1300R
General
Power source .......... 14.4 V DC (10.8 15.1 V allowable) Grounding system ........................................ Negative type Max. current consumption ...................................... 10.0 A Dimensions (mounting size) ...... 178 (W) 50 (H) 159 (D) mm (front face) .............. 188 (W) 58 (H) 19 (D) mm Weight ...................................................................... 1.4 kg Electrode dark current .................................... 6mA or less
CD player
System .................................... Compact disc audio system Usable discs .................................................. Compact disc Signal format...................... Sampling frequency: 44.1 kHz Number of quantization bits: 16; linear Frequency characteristics................ 5 20,000 Hz (1 dB) Signal-to-noise ratio ........ 94 dB (1 kHz) (IEC-A network) Dynamic range ............................................ 92 dB (1 kHz) Number of channels ............................................ 2 (stereo)
Amplifier
Maximum power output ...................................... 45 W 4 Continuous power output .................................... 25 W 4 (DIN45324, +B = 14.4 V) Load impedance .......................... 4 (4 8 allowable) Preout maximum output level/output impedance ............................ 2.2 V/1 k Equalizer (3-Band Equalizer) (Low) .................................................. Level: 12 dB (Mid) .................................................... Level: 12 dB (High) .................................................. Level: 12 dB Loudness contour (Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz) (Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz) (High) ................ +11 dB (100 Hz), +11 dB (10 kHz) (volume: 30 dB)
FM tuner
Frequency range ...................................... 87.5 108 MHz Usable sensitivity .................... 9 dBf (0.8 V/75 , mono, S/N: 30 dB) 50 dB quieting sensitivity .... 15 dBf (1.5 V/75 , mono) Signal-to-noise ratio ...................... 70 dB (IEC-A network) Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ...................... 30 15,000 Hz (3 dB) Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)
MW tuner
Frequency range ........................ 531 1,602 kHz (9 kHz) Usable sensitivity .............................. 18 V (S/N: 20 dB) Selectivity .................................................. 50 dB (9 kHz)
LW tuner
Frequency range ........................................ 153 281 kHz Usable sensitivity .............................. 30 V (S/N: 20 dB) Selectivity .................................................. 50 dB (9 kHz)
Note:
Specifications and the design are subject to possible modification without notice due to improvements.
74
DEH-1330R,1300R,1310
- DEH-1310
General
Power source .......... 14.4 V DC (10.8 15.1 V allowable) Grounding system ........................................ Negative type Max. current consumption ...................................... 10.0 A Dimensions (mounting size) ...... 178 (W) 50 (H) 159 (D) mm (front face) .............. 188 (W) 58 (H) 19 (D) mm Weight ...................................................................... 1.4 kg Electrode dark current .................................... 6mA or less
CD player
System .................................... Compact disc audio system Usable discs .................................................. Compact disc Signal format .................... Sampling frequency: 44.1 kHz Number of quantization bits: 16; linear Frequency characteristics .............. 5 20,000 Hz (1 dB) Signal-to-noise ratio ...... 94 dB (1 kHz) (IEC-A network) Dynamic range ............................................ 92 dB (1 kHz) Number of channels ............................................ 2 (stereo)
Amplifier
Maximum power output ...................................... 45 W 4 Continuous power output .................................... 25 W 4 (DIN45324, +B = 14.4 V) Load impedance .......................... 4 (4 8 allowable) Preout maximum output level/ output impedance .................................... 2.2 V/1 k Equalizer (3-Band Equalizer) (Low) .................................................. Level: 12 dB (Mid) .................................................... Level: 12 dB (High) .................................................. Level: 12 dB Loudness contour (Low) ..................+3.5 dB (100 Hz), +3 dB (10 kHz) (Mid) ..................+10 dB (100 Hz), +6.5 dB (10 kHz) (High) ..................+11 dB (100 Hz), +11 dB (10 kHz) (volume: 30 dB)
FM tuner
Frequency range ............................................ 65 74 MHz 87.5 108 MHz Usable sensitivity ......................................................10 dBf (0.9 V/75 , mono, S/N: 30 dB) 50 dB quieting sensitivity ........................................ 15 dBf (1.5 V/75 , mono) Signal-to-noise ratio ...................... 70 dB (IEC-A network) Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ...................... 30 15,000 Hz (3 dB) Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)
MW tuner
Frequency range ........................ 531 1,602 kHz (9 kHz) Usable sensitivity .............................. 18 V (S/N: 20 dB) Selectivity .................................................. 50 dB (9 kHz)
LW tuner
Frequency range ........................................ 153 281 kHz Usable sensitivity .............................. 30 V (S/N: 20 dB) Selectivity .................................................. 50 dB (9 kHz)
Note:
Specifications and the design are subject to possible modification without notice due to improvements.
75