Vous êtes sur la page 1sur 28

Technical Data Sheet

00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter

Magnetic Flowmeter Material Selection Guide

www.rosemount.com

Technical Data Sheet

Magnetic Flowmeter
FIGURE 1. Cutaway View of a Magnetic Flowtube

00816-0100-3033, Rev CA Catalog 2008 - 2009

Liner

Electrodes

INTRODUCTION
The purpose of this guide is to provide a general resource for the selection of materials for the magnetic flowmeter. One of the advantages of the electromagnetic flowmeter is that it is suitable for a wide variety of applications including severely corrosive chemicals and highly abrasive slurries. The key to this versatility is that there is a large choice of materials available for the electrodes and the flowtube liner.

DISCLAIMER
Rosemount Inc. neither represents nor warrants the accuracy or sufficiency of the information set forth in this guide for specific end-user applications. Ultimate responsibility for materials selection remains with the end-user. Nothing in this guide constitutes a change to the terms and conditions under which the Rosemount product was sold. The data presented in this guide is based on field experience and published data. However, because of the wide variety of processes and applications it is impossible to guarantee material compatibility in a given process without performing corrosion tests under actual operating conditions. Therefore, the final decision of material resides with the user. Additionally, some of the process fluids listed in this guide do not meet the minimum conductivity requirements (5 micro-siemens/cm) for a magmeter. However, they are listed to aid the user in instances where there may be trace amounts contained in the process fluid.

Flow-2

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Electrode Material
Each electrode material has two considerations corrosion rate per year and temperature limit. The following codes define the compatibility with each chemical listed:
Corrosion Rate Per Year Less than 0.002 in. Less than 0.020 in. Less than 0.050 in. Greater than 0.050 in. No Information Temperature Limit 248 F (120 C) 212 F (100 C) 176 F (80 C) 140 F (60 C) 68 F (20 C) Code A B C N (Blank) Code 1 2 3 4 5

HOW TO USE THIS GUIDE


Chemical names are listed in alphabetical order. Each chemical may have one or more temperature and concentration combination. In instances where the temperature limit is not given or the compatibility information is left blank, this indicates there is no information available.

Flowtube Liner
Each liner material has two considerations compatibility to the chemical and temperature limit. The following codes define the compatibility with each chemical listed:
Compatibility Resistant Not Resistant No Information Temperature Limit 248 F (120 C) 212 F (100 C) 176 F (80 C) 140 F (60 C) 68 F (20 C) Code A N (Blank) Code 1 2 3 4 5

NOTE Temperature limit values are generally conservative and were chosen to best represent data available. Note that if an A1 code is specified the actual temperature limit of the material may be in excess of 248 F.

NOTE Temperature limit values are generally conservative and were chosen to best represent data available. Note that if an A1 code is specified the actual temperature limit of the material may be in excess of 248 F.

REFERENCES
The data found in the Material Selection Guide is based on field experience and data from the follow sources: National Association of Corrosion Engineers (1985) Corrosion Data Survey. Miller, Richard W. (1989) Flow Measurement Engineering Handbook. Schweitzer, Philip A. P.E. (1991) Corrosion Resistance Tables.

Flow-3

Technical Data Sheet

Magnetic Flowmeter
Example
This example illustrates how to use the Material Selection Guide to choose compatible flowtube materials for a given process. The example process fluid is 98% sulfuric acid at 100 F (38 C).
Flowtube Liner Process Liquid Maximum Concentration Polyure thane Linatex Rubber Electrode Material

00816-0100-3033, Rev CA Catalog 2008 - 2009

PTFE

ETFE

PFA

Neoprene

Hastelloy 316 SST C-276

Tantalum

Platinum -10% Iridium

Titanium

Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid

70% 80% 90% 95% 98% 100%

A1 A1 A1 A1 A1 A1

A1 A1 A1 A1 A1 A1

N N N N N N

A3 N N N N N

N N N N N N

N B5 B5 B3 B3 B3

B3 A5 A4 A5 A5

B1 B1 B1 B1 B1 B1

A1 A1 A1 A1 A1 A1

N N N N

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Liner Compatibility (from table) PTFEresistant up to 248 F (120 C) Polyurethanenot resistant ETFEresistant up to 248 F (120 C) Neoprenenot resistant Natural Rubbernot resistant Rytonnot resistant 316 SSTcorrosion rate of less than 0.020 in. per year, up to 176 F (80 C) Hastelloy C-276corrosion rate of less than 0.0020 in. per year, up to 68 F (20 C) Tantalumcorrosion rate of less than 0.020 in. per year, up to 248 F (120 C) Platinum-10% Iridiumcorrosion rate of less than 0.0020 in. per year, up to 248 F (120 C) Titaniumcorrosion rate of greater than 0.050 in. per year (not recommended)

Electrode Compatibility (from table)

The proper material selection would be a PTFE or ETFE liner with platinum-10% Iridium electrodes. Rosemount Inc. does not guarantee the accuracy of this guide. See DISCLAIMER on page 2.

Flow-4

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter

MATERIAL SELECTION GUIDE


Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Acetaldehtde Acetamide Acetic Acid Acetic Acid Acetic Acid, Glacial Acetic Anhydride Acetone Acetone Acetophenone Acetonitrile Acetyl Chloride (dry) Acetylene Acetylene Tebrabromide Acetylene Tetrachloride Acid Mine Water Acrylontrile Adipic Acid Alcohol & Glycerin Alcohol, 2-Aminoethanol Alcohol, Allyl Alcohol, Amyl Alcohol, Butyl Allyl Chloride Alum Alum Alumina Aluminium Flouride Aluminium Hydroxide Aluminum Ammonium Sulfate

Maximum Concentration

PTFE

ETFE

100% 100% 50% 75% 100% 100% 50% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 10% 100% 100% 100% 100% 100%

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

A2 A1 A1 A2 A2 A1 A4 A4 A1 A4 A4 A1 A A

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

N N N N N N N N

A2 A3 A4 A4 N A5 N N N N A3

N N N N N N N N N N A5

B4 B1 B3 N A1 B1 B1 A1 B1 B4 B1 A1

A4 A3 A1 A1 A1 A3 A4 B3

B5 A1 A1 A1 A5 A3 A1 B5 B5 B5 B5

A5 A A A A2 A

A1 A1 A1 A A1 A3 A3 B3

A2 B5

B3

A2

A1 A1 A

A4 A1

A1 A1 A

A4 A4 N

A5 A5

B3 B3 A

B3 A3 A

B3 B3 A

A2 A

B3 A1 A

A1

A3

A1

A5

A5

A1

B1

B1

A2

B3

A1 A A1 A A A

A3 A1 A A A1

A1 A A1 A A A

N N A3 N

N A4

A5 B B3 N N B

B B4 A N N

A B5 A N A

A2 A A A A A

A A3 A

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-5

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Aluminium Sulfate Aluminum Chloride Aluminum Chloride Aqueous Aluminum Chlorohydrate Aluminum Fluoride Aluminum Hydroxide Aluminum Oxychloride Aluminum Nitrate Aluminum Potassium Sulfate Aluminum Sulfate Amidosulfonic Acid Amino Acids Ammonia (Anhydrous) Ammonium Bicarbonate Ammonium Bicarbonate Ammonium Bifluoride Ammonium Bifluoride Ammonium Bisulfate Ammonium Bromide

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

100% 20% 100%

A A A1 A A1

A A A1 N A5 A A3 A4

B N N

B A A3

A A B1

A A5 A5

B B N

100% Sat 100% 100% Sat 100%

A A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

A A1 A1 A1 A1 A1 N A3 A3 A4 A4 N A3 A3 A4

N B5 A1

A N

A A5 A5 B4

B5

A5

B3 N

B5 B3

A A3

A3 A3

Sat 100% 100% 100% 50% 100% 50% 100% 100% 5%

A1 A A A1

A1 A

A3

A4

B3 N

B3 N

A1 A

A2 A

A3

A1 A A1 A A1 A A1

A1 A A1 A

A5 N

A3 N

A1 B B4

B1 N B5 B B1

A1 A B3 N A A2 A A5 A A A2

A1 A A3 N

N N

N N A

N N

A1

A1 A

A1

A1

B1

A5

B3

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-6

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Ammonium Carbamate Ammonium Carbonate Ammonium Carbonate Ammonium Chloride Ammonium Chloride Ammonium Dichromate Ammonium Flouride Ammonium Fluoride Ammonium Fluoride Ammonium Hydroxide Ammonium Nitrate Ammonium Nitrate Ammounium Perchlorate Ammonium Persulfate Ammonium Phosphate Ammonium Sulfate Ammonium Sulfide Ammonium Thiocyanate Amyl Acetate Amyl Alcohol Amyl Chloride Aniline Aniline Hydrochloride Anthraquinone Anthraquinone-S ulfonic Acid

Maximum Concentration

PTFE

ETFE

50% 50% Sat 50% Sat 100% 10% 25% 100% 25% 5% 100% 100% 100% 100% 40% 100% 100% 100% 100% 100% 100% 100% 100% 100%

A A A1 A1 A1 A A1 A1 A1 A A1 A1 A A1 A A1 A2 A A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A2 A2 A1 A1 A1 A1 A A1

A A A1 A1 A1

N N

N N A3 A3 A4 A4 A4

N B B1 N N

B B B1 A3 B1 A A3 A3 A1 A2 A5 A2 A2

A3 A3 A3

A3

A1 A1 A A1 A A1 A5 A N

A5 A3

A4 A5

B5 N N

A3 A3 B B1 B

N N N A1 A A3 A1

A A A A2 A1 A1 A1 A2 A A1

B5 A5

A3 N A3

A5 A1

A5 A

A4

A1

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

N N N

A3 A3 A3 A4 A3

A5 A4 A4

N N B1 B1 B5

N N B3

A5 A A1 B5

B5 A A3

B3 A1 B3 A5 B1 N B3 B5

B5 B1 B1 B1 B3 B3 B3 B3 A2 A2 A2 A1 A2 A2 A3 B4 A3 A3

N N N

N A4 N N N

N A4 N N N

A1 B1 B4 A1 N

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-7

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Antimony Pentoxide Antimony Trichloride Aqua Regia Arsenic Acid Arsenous Acid Asphalt Emulsions Barium Acetate Barium Carbonate Barium Chloride Barium Hydroxide Barium Hydroxide Barium Sulfate Barium Sulfide Battery Acid Bauxite Slurry Beer Benzaldehyde Benzene Benzene Sulfonic Acid Benzoic Acid Benzonitrile Benzoyl Chloride Benzyl Alcohol Benzyl Chloride Bismuth Carbonate Black Liquor Bleach, Active Chlorine 12.5% Borax Boric Acid Boron Fluoride Brine Acid

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

100% 100% 100% 100% 100% 100% 100% Sat Sat 50% Sat 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%

A A1 A1 A1 A A1 A A1 A1 A A1 A1 A1 B A1 A1 B1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A A1 A3 A3 A1

A A1 A1 A1 A A1 A A1 A1 A A1 A1 A1 B A1 A1 B1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A A1 A N A4 N A3 N N A4

N N N B1 N A5 N B5 B3 A B1 B3 B3 N A1 B1 B1 B3 B1 A5 A1 B3

N B3 N B3 N

A B3 A1 A

A A2 N A2 A B5 A5

A1 A1

A4 A3 A A3 A4 A4 B A5

A3 A5

N B1 A3 B B1 N N A A5 B3 B3 B3

A B5

A A A2 A2 A2 A A4 A A A2 A2 A2 A2 A2 A2 A2 A1

A5

A B1 B3 B5 A A5 B3 A2

A1 A1 A1 A A1 A3 A3 A3 A1 A3 A4 A1 A1 A1 A1 A3 A1 A1 A1

A4 A3 A4

A3 A3 B5 A B5 B5 A2 B3 A1 A1 B3

A N

A5

N N A3 A4 N N N

N N

B3

A3 A1 A1 B3 B2 B5 N

N N A

A3 A5 A3 A3 A4

A5 A5 A4 A4 A3

B5 N A1 B1 N N

C1 A4 A5 A1 N A4

N A1 N A

A A A A

B3 A3 N A

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-8

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Bromic Acid Bromine Liquid Bromobenzene Bromoform m-Bromotoluene Butadiene (Butylene) Butane Butanediol Butyl Acetate Butyl Acrylate Butyl Alchol Butyl Alcohol Secondary Butyl Alcohol Tertiary n - Butylamine sec - Butylamine tert - Butylamine di-n-Butyl Amine tri-n-Butyl Amine Butyl Amine Butyl Bromide Butyl Chloride Butyl Ether Butyl Phenol Butyl Phthalate Butylene (Butadiene) Butyraldehyde Butyric Acid n-Butyl Mercaptan Cadmium Chloride Calcium Bisulfate Calcium Bisulfite Calcium Carbonate Calcium Chlorate Calcium Chlorate Calcium Chloride Calcium Chloride

Maximum Concentration

PTFE

ETFE

100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 30% 100% 50% Sat

A1 A1 A1

A1 A1 A1 A1 A1 A1 A1

A1 A1 A3 A A A2 A1 A A2 A A1 A1 A1 A5 A A A A A1 A1 A3 A2 A4 A1

A1 A1 A1

A5 N N

B5 A1 A1

A2 A2 A3

A1 A1 A1 A1 A1 A1 A1

N A5 N

A5 N

N N N

B1 B1 B1 A1 B5 B5 B1

B3 B2 B1 B3 B5 B5 B3

B5 A5 A1 B5 B5 B5 B5 A2 A2 A2 A5 A1 A3 B3 B3 B3 B3

A3

A4

A1 A1 A1 A1 A1 A1 A A1 A1 A A1 A1 A1 A A1 A A1

A1 A1 A1 A1 A1 A1 A A1 A1 A

N N N A4 N

B5 A5 A1 B3 B1 A2 B1 B3 N B3

B5 B3 B3

B3 B2 B3 B5

A2 A2

B5

B3

A1 A1

A2 A1 B1 N N B5 B3 B3 B3 A A1

B1

A2

A3

A2 A1 A5 A2 B3 B3 A1

A2 A A5 A2 A2 A2 A2 A2 A3 A2 B4 B4 A A3

A1

A1 A1 A1 A A5 A3

A1

A N

A5 A A3

B1 B3 B4

A1 A A1

A1 A A1 A A5

A4

B3 N B3

A A3

A4

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-9

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Calcium Hydroxide Calcium Hydroxide Calcium Hypochlorite Calcium Nitrate Calcium Nitrate Calcium Oxide Calcium Sulfate Calcium Sulfate Calcium Sulfide Cane Sugar Juice Caprylic Acid Carbon Dioxide (Dry) Carbon Dioxide (Wet) Carbon Disulfide (Bisulfide) Carbon Slurry Carbon Tetrachloride Carbonic Acid Castor Oil Caustic Soda Cellosolve Cheese Chloral Hydrate Chlorinated Brine Chlorinated Phenol Chlorine (Liquid) Chlorine Dioxide Chlorine Dioxide Chlorine Water Chloroacetic Acid Chloroacetic Acid (50% H O) Chlorobenzene (Phenylchloride) Chlorobenzyl Chloride
2

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

25% Sat Sat 10% 100% 100% 10% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 50% 100% 100% 100% 100% 100% 100% 15% 100% Sat 100% 50% 100% 100%

A1 A1 A1 A A1 A1 A A1 A A1 A1 A1 A1 N A1 A1 A1 A A1 A A1

A1 A1 A1

A1 A1 A1 A A1 A1 A A1 A

A5

A2 A2 A5

A3 A3 A5

B3 B3 B5 B B1 B5 A B3 A B1 B1 B3 B1 A A1 B1 B4 B B1 A

A4

A1 A1 B1

A5 A2 A2 A2 A2 A2 A A

A2 A2 A3 A B3 A A3 A B3 A5 A5 A3

A1 A1 A A1 A

A5 N N N

A3 A5 N A4 A

A4

B B3 B5 B1 A B1 A1 B3 B3 A A5 A5 A5 B3 A

A B5 A B3 A B1 B1 A1 A5 A A1 B1 N B3 A

A3

A3 A1 A1 A4

A1 A1 A1 A1 N A1 A1 A1 A A1 A A1

A5 A5

A3 A3 N

A4 A4 N

A1 A1

A1 A1 A1 A A1 A3 A A

A N

N N A5 A4 N N N

N A3 A4 N

A A3 A3 B B3 A

A1 A A

N N

A1 A1 A A1 A1 A1 A1

A A1 A A5

A1 A1 A A1 A1 A1 A1

N N N N N N N

N N A4 N N N

N N N N N N B1

A5 A4 N A3 A4 B3 A1

B1 A1 A B1 A1 A3 B1

N N A A2 A2 A3 A A3 A3 A3 B3

A2 A3 A

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-10

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Chloroform Chlorohydrate Aluminum Chlorohydrin Chlorohydroxide (wet) Chlorophenol, 5% Aqueous Chlorosulfonic Acid Chlorosulfuric Acid Chromic Acid Chromic Acid Chromic Acid Chromic Chloride Chromium Fluoride Chromium Sulfate Chromium Sulfate Chromyl Chloride Clorox Bleach Solution(5.5% Chlorine) Citric Acid Clay Slurry Coal & Water Slurry Coffee Extract Cola Syrup Copper Chloride Copper Chloride Copper Cyanide Copper Fluoride Copper Nitrate Copper Nitrate Copper Oxychloride Copper Sulfate Copper Sulfate Copper Sulfate Copper Sulfide

Maximum Concentration

PTFE

ETFE

100% 100% 100% 100% 100% 100% 100% 30% 50% 100% 100% 100% 50% 100% 100% 100%

A1 A

A2

A1 A

A5 N

B3 N

A3 A

A2 A A1

A3

A1 A1 A A1 A1 A A4 A4 A A A5

A1 A1 A A1 A1 A A5 A5 N N N N N

B1 N N B1 B4 N

A5 A2 B B3 B3 N B3 A B1 A1 A

A2 A1 A A2 A2 A2 A3 A3 B A3

A A A A1 A1 A3 A3

A A A A1 A1 N N N N B N B3 B5 B B B3 A A B3 A2 A A2 B5

50% 100% 100% 100% 100% 5% 100% 100% 100% 50% 100% 100% 40% 70% 100% 100%

A1 A N A A A A1 A1 A1 A A1 A A A A1 A

A3

A1 A N A A A A1 A1 A1 A A1 A A A A1 A

N A A A A A A5 A

A A A A A A A3 A4 A4 A3

A4

B1 A N A A N N B3 N B A1 N B B B1 B

A3 A A A A B B3 A4 N N B5 N A A A3 B

A1 A A A A A A1 B1 N A B1 N A A A1 A

A2 A A A A N N A A A A A A2 A A

A3 A A A A A A3 A5 A A5

A1 A1 A1 A A1

A4 A4

A3

A A

A1

A A A3

A4

A B A3

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-11

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Corn Oil Cottonseed Oil Cresol Cresylic Acid Cresyldiphenyl Phosphate Croton Aldehyde Crude Oil Cupric Chloride Cupric Chloride Cyclohexane Cyclohexanol Cyclohexanone DDT Dairy Products Decalin Decane Detergents Dextrin Diacetone Alcohol 1.2 Dibromo Propane Dibutyl Phthalate Dichloroacetic Acid Dichlorobenzene Dichloroethylene Dichloropropioni c Acid Diesel Fuel Diethylamine Diethyl Benzene Diethyl Cellosolve Diethyl Ether Diethylene Triamine Diglycolic Acid Diisobutyl Ketone Diisobutylene Dimethylamine Dimethyl Aniline Dimethyl Formamide

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

100% 100% 100% 100% 100% 100% 100% 50% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%

A1 A1 A1 A1

A1 A1

A1 A1 A1 A1

N N

A3 A4 N N

N N N N

B1 B4 B5 B1

B3 A1

B2

B3 B5

A1 A1 A1 A A1 A1 A1 A

A3 A1

A1 A1 A1 A A A A1 A1 A3 A

A1 A1 A1 A A1 A1 A1 A

A5

A5 N A4 N N N

N N

A3 N N B1 B5 B3 A

B3 A5 B3 N B3 B5 B3 A

B3 A5 A5 A B5 B5 B5 A2 A

N A A2 A2 A2 A

A5 B3 B A1 B5 B5 A2 A

A1 A1 A1

A1 A1 A1

A5

A3 A3 N

B1 B1

A5 B5 A3

A4 A2 A2

A4 A2

A1 A1 A1 A1

A4 A4 A4 A4 A A1 A2 A A1 A3 A3 A3 A A A5 A1 A1

A1 A1 A1 A1

N N N N

B1

B3

B3 A1

A1

B3 A1

B5 B3

A1 B3

B3

A2 A2

B3

A1 A1 A1 A1 A1 A1

A1 A1 A1 A1 A1 A1

A5 A5 A5 N

N A5

A5 B1 B3

B3 A2

B3

B2

B5

B5 B5 B3 A2

B5 A5 B3

A3

B1

B3

A1 A1 A1

A1 A1 A1

N N A4

B5 N N B1

A2 A2

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-12

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Dimethyl Phthalate Dimethyl Sulfate Dimethyl Sulfoxide Dioctyl Phthalate Diphenyl Ether Disulfide p-Dioxane Divinyl Benzene Dowtherm (Diphenyl) Dyes pichlorhydrin Ethylamine Ethers Ethyl Alcohol Ethyl Acetate Ethyl Acrylate Ethyl Chloroacetate Ethyl Chloride Ethyl Cyanoacetate Ethyl Acetoacetate Ethylene Bromide Ethylene Chloride Ethylene Chlorohydrin Ethylene Diamine Ethylene Dichloride Ethylene Glycol Ethylene Oxide Esters Fatty Acids

Maximum Concentration

PTFE

ETFE

100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%

A1

A3 A A3 A4 A A A A4

A1

A5

A1 A1

A1 A1 N N B5 A2

A1 A A1 A1 A1 A1 A1

A1 A A1 A1 A1 A1 A1 N

A3 N N N N N N

B3 A B1 A3 B1 B1 B3

B3 A A5 B3 A2 B1 A3

B3 A B5 B3 A3 B3 B5 A A2

B3 A

A4 A A3 A1 A4 A3 A A1 A A

N N N N

A1 A2

B5 A3 A3

A1

A1

A1

B3

A3

A1

A3

A1 A1 A1 A1 A1 A1 A1 A1

A1 A1 A4 A5

A1 A1 A1 A1 A1

N N N N N A5 A4 N A4

N N N A5 N A4 N N

A3 B2 B3 B1 B1 B1 B1 A1

A3

B5 B3

B3 A3 B3 A2 A2 A2 A2 A1 A5 B3 A3 A5 A3

B3 N B2 A1 A5 A1

B3 B5 A3 A5 A5 A1

A1 A2 A A1

A1 A1 A1

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-13

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Ferric Chloride 50% H2O Ferric Hydroxide Ferric Nitrate Ferric Nitrate Ferric Sulfate Ferric Sulfate Ferrous Chloride Ferrous Chloride Ferrous Hydroxide Ferrous Nitrate Ferrous Sulfate Ferrous Sulfate Ferrous Sulfate Fluoroboric Acid Fluosilicic Acid Fluosilicic Acid Formalhehyde Formic Acid Formic Acid Formic Acid Freon F-11 Freon F-12 Freon F-22 Fruit Juices, Pulp Fuel Oil Fumaric Acid Furane Furfural Gallic Acid Gas Oil Gas Oil Gas Manufactured Gasoline Leaded Gasoline Unleaded Gasoline - Sour Glacial Acetic Acid Glucose (Corn Syrup) Glycerin (Glycerol)

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

50% 100% 10% 100% 10% 100% 10% Sat 100% 100% 10% 50% 100% 100% 40% 100% 35% 50% 80% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 35% 100% 100% 100% 100% 100% 100% 100% 100%

A1 A1 A1 A A1 A A1

A1 A1 A1 A1 A1 A1 A A1

A1 A1 A1 A A1 A A1

A4 A5 A3

A4

N A5 B1 A3 N N N

B3 A5 A5 A4 B N B1

A3 A3 B3 A2 A3 A A3

A A5 A2 A2 A2 A A2 A2

A3 B3 A5 A2 A A A3

A4

A3 N A5

A4 A4

A1 A A1 A1 A1 A A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

A1 A1 A1 A2 A1 A1 A1 A3 A2 A2 A1 A A A3 A3

A1 A A1 A1 A1 A A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

N N

N N N N N A5 A5 N N

A3 N N A3 A4 N A4 A4 A4 A4 A5 A3 A3 A5 A3 A4

A4

A4 A4 A5 N N N N N N N

B5 N N B3 N N B3 A3 B1 B1 B3 B1 B1 B1 B1 B4

B N N B2 A3 N B5 B3 A2 A3 A2 A5 B1 A3 B3

A A A B1 N N N A1 A1 A1 A1 B5 B5 A5 B3

A A A A A A2 A2 A2 A2

A A A A5 N N N A3 B5 B5 B5 B5 B5 A5 A5

A1 A1 A A A1 A1 A1 A1 A A1 A1

A1 A1 A3 A1

A1 A1 A A A1 A1 A1 A1 A A1

N N

A3 A5

N A4

B1 B1 N N B5 B5 B5 B5 N B1 A3

B5 B3 B N

A1 B5 N N

A3 A A

A5 A5 A5

A5 A5 A5

N N N

A5 A1 B1 A A A1

A5 A5 B5 A A B5

A5 B5

A A A A A3

A5 A5 A3

A5 A4

A1

A1

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-14

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Glycol Glycolic Acid Green Liquor Heptane Hexane Hormaldehyde Hydrazine Hydrazine Dihydroanioride Hydriodic Acid Hydrobromic Acid Hydrochloric Acid Hydrochloric Acid Hydrochloric Acid Hydrocyanic Acid Hydrofluoric Acid Hydrofluoric Acid Hydrofluoric Acid Hydrofluorosilicic Acid Hydrofluorosilicic Acid Hydrogen Cyanide Hydrogen Fluoride Hydrogen Peroxide Hydrogen Peroxide Hydrogen Peroxide Hydrogen Sulfide Hydrogen Phosphide

Maximum Concentration

PTFE

ETFE

100% 100% 100% 100% 100% 100% 100% 100% 100% 50% 5% 20% 40% 10% 20% 35% 70% 35% 100% 100% 100% 30% 50% 90% 100% 100%

A1 A1 A1 A1 A1 A

A1 A1 A1 A1 A A A A1

A1 A1 A1 A1 A1 A

N A5

A4 A3 A4 A3 A5

A5 A4 N N

B5 B1 B B1 A1 N

B3 B A3 A1 B

B3 A B3 B5 A

A A2 A2 A

A3 A B3 A4

A1 A A1 A1 A1 A1 A1 A1 A1

A1 A

A5

N N

B5 N A5 A5 B B3 B3 B3 B5

A1 A A1 A1 A N N N N

A2 A2 A2 A2 A2 A2 A2 A2 A

A3

A1 A1 A1 A1 A1 A1 A1 A

A1 A1 A1 A1 A1 A1 A1

A5

A5 A5

A4 A3 A5 A5 A5 N A5

N N B3 N N N B5

N N B N N N N

N N N N

N A3 A3 A3 A4

A1 A1 A1 A1 A1 A1 A1

A1

A1 A1

N N N N N N N N A3

A5 N N N N N

A5 A5 B1 B1 A5 B1

A5 B1 A5 B5 A3 A5

B5 N B1 B1 B1 A1

A B A2 A2 A2 A5 A3 A3 B3 A5

A1 A4 A4 A1 A4

A1 A1 A1 A1 A1

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-15

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Hydroquinone Hydroxy Acetic Acid Hydroxy Acetic Acid Hypochlorous Acid Hypochlorous Acid Iodine Idoform Iron Chloride Iron Nitrate Iron Sulfate Isobutyl Alcohol Isopropylamine Jet Fuels - JP4 Jet Fuels - JP5 Kerosene Ketones Kraft Liquor Lactic Acid Lard Oil Latex Lauric Acid Lauryl Chloride Lauryl Sulfate Lead Acetate Lead Nitrate Lime Slurry Linoleic Acid Linseed Oil Lithium Bromide Lithium Chloride Lithium Chloride Lithium Hydroxide Lubricating Oil

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

100% 35% 70% 20% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 30% 100% 10% 100%

A1 A1 A1 A A1 A1 A1 A A A

A1

A1 A1 A1 A

A3

A5

B1 B B N

B3 B B B B5 A1 N B B B

B3 A A N B1 B1 B3 N A A

A1 A A A A2 A1 A2 A A A

B3

B B5 A5 B2

A1 A2 A2

A1 A1 A1 A A A

N N

A4 N

N N A1 N N N

A1 A1 A1 A1 A1 A1 A1 A A1 A1 A1 A1 A A1 A1 A1 A1 A A1 A1

A A A2 A2 A1 A1 A1 A1 A1 A1 A A1 A5 A1 A1 A1 A5 A1 A1

A1 A1 A1 A1 A1 A1 A1 A A1 A1 A1 A1 A A1 A1 A1 A1 A A1 A1

N N N

N N A3 N A5 A5 N N

N N N

A5 N

B1 B1 B1 B1 A5 B1 B5 A B5

A5 A5 B2 A5 A5 B2 A5 A B5

B5

A5 A5 A5 A5 A2 A A2 A1 A

A1 A5 A

A3 A3 A N A3 A3

A5 A3 N N

B3 B5 A B1 B5 B1 N N B3 B4

B3 B3 A B1 B5 A3 A B3

B3 A A B1 B3 A3 A B3

A2 A2 A

A3 A B3 A5 A3 A

A A

A3

A5

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-16

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid M-Cresol (crude) Magnesium Bisulfate Magnesium Carbonate Magnesium Carbonate Magnesium Chloride Magnesium Chloride Magnesium Hydroxide Magnesium Nitrate Magnesium Sulfate Magnesium Sulfate Magnesium Sulfate Maleic Acid Maleic Anhydride Malic Acid Mercuric Chloride Mercuric Chloride Mercuric Cyanide Mercuric Nitrate Mercury Methacrylic Acid Methane Methane Sulfonic Acid Methyl Alcohol Methyl Benzoate Methyl Bromide Methyl Cellosolve

Maximum Concentration

PTFE

ETFE

100% 100% 10% 100% 42% 100% 100% 100% 25% 40% 100% 100% 100% 100% 60% 100% 100% 100% 100% 100% 100% 50% 100% 100% 100% 100%

A A A1 A1 A1 A1 A1 A A A1 A1 A1 A1 A A1 A1 A1 A1 A1 A1

A A A1 A1 A1 A1 A1 A A A1 A1 A5 A5 A3 N A4 A5 A5 A5 A3 A2 A3 A3 A3 A3 A4 A4 A3 A4

B B B3 B2

B B A B3 A1 A1 A1 A A A5 A1

A2 B1 B A B1 B1

A2 A5 N B3 A B3

A5 B3 A A4 A4 B3

A A A A A

A5 A5 B A B3 A3

A1 A A1 A1 A1 A1 A1 A1 A1 A1 A1

A1 A A1 A1 A1 A1 A1 A1 A1 A1 A1

A5 A N N A5 A3 A3

A5

A1 N B1 B5 N A1 A1

B3 N

B3 A A1

A A2

A3 A B3 A5

A1 A1 A1 A1 A A1 A2 A1 A A1 A1

A4 A4 A5 A4 N

B5

B1 B1 B1 B1 A2 N

A5

A1 A3

A1 A3

A5

A3 N A3

A4 N

B1 B1 B1

A1

B1 B3 B5

B3

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-17

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Methyl Chloride Methyl Chloroform Methyl Chloromethyl Ether Methyl Cyanoacetate Methyl Ethyl Ketone Methyl Methacrylate Methyl Salicylate Methyl Sulfuric Acid Methyl Isobutyl Ketone Methyl Trichlorosilane Methylene Bromide Methylene Chloride Methylene Iodide Milk Mineral Oil Molasses Monochlorobenz ene Monoethanolami ne Morpholine Motor Oil Mud Drilling Naphtha Naphthalene Nickel Chloride Nickel Chloride Nickel Chloride Nickel Nitrate Nickel Nitrate Nickel Sulfate Nickel Sulfate

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

100% 100% 100%

A1 A1

A1 A4 A

A1 A1

N N

A1

B5

B3

A3

100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 10% 20% 100% 10% 100% 10% 100% A1 A1 A1 A1 A1 A1

A A2 A4 A3 A3 A1 A A A3 A A1 A1 A1 A1 A1 A1 A1 N A1 A1 A A A1 A A1 A A1 A1 A2 A4 A4 A1 A1 A1 A1 A1 A1 A1 N A1 A1 A A A1 A A1 A A1 A5 A5 N A3 A3 A3 N A5 N A A5 N N N A5 N A4 N A5 A1 B1 A1 B5 A3 B1 B1 A B3 A1 N N B5 A1 B B3 A5 A5 B5 B3 A1 A1 A5 B4 A3 A A A5 A5 A B4 B3 A1 N N N B1 A3 N A3 A1 A1 A1 A1 A1 N N N N N N N B5 N B1 B3 B1 B5 B3 B3 B5 B5 A1 B3 B3 B3

A2 B2

A1 A1

N N

A1 A1 A1

A3 A3 A3

A4 A4 A4

A B3 B3 A N N B B1 B B3

A B5 B3 B A B3 B B3 A3 N

A A2 A1 A A A2 A A2 A2

A B5 A3 B N A3 A5 B3 N

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-18

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Nicotine Nicotonic Acid Nitric Acid (Anhydrous) Nitric Acid Nitric Acid Nitric Acid Nitric Acid Nitric Acid Nitric Acid-Sulfuric Acid Nitrobenzene Nitrogen Nitrogen Dioxide Nitromethane Nitrous Acid Octane Octene Oleic Acid Oleum Oxalic Acid p-Dioxane Palmitic Acid Paper Stock Perchloric Acid Perchloric Acid Perchloric Acid Perchlorethylene Petrolatum Petroleum Oils, Refined Petroleum Ether Phenol Pheno (Carbolic Acid) Phenolsulfonic Acid Phenylhydrazine Phenylhydrazine Hydrochloride o-Phenylphenol

Maximum Concentration

PTFE

ETFE

100% 100% 100% 10% 20% 40% 50% 70% 50%/50%

A1 A1 A1 A1 A1 A1 A1 A1 A1

A3 A1 N A4 A4 A4 A4 A5 A3

A1 A1 A1 A1 A1 A1 A1 A1 A1

N N N N N N

N A3 N N N N N N

N N N N N N

B3 B1 A5 A3 A5 A5 A5 A5 A4

B5 B5 A3 A4 A5 A5 A5 A1 A1 A1 A1 A1 A1 B5 A2 A A2 A A B3 A1 A1 A1 A1 A1

100% 100% 100% 100% Conc 100% 100% 100% 100% Sat 100% Conc 100% 10% 70% 100% 100% 100% 100% 100% 10% 100% 100% 100% 100% 100%

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A A1 A1 A1 A1 A1 A1

A1 A1 A3 A3 A3 A1 A A1 A4 A2 A1 A1 A2 A4 A1 A1 A1 A3 A2 A3 A

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A A1 A1 A1 A1 A1 A1

N A3 N N A2

N A3 A5 N

B1 A1 B5 B5 B5 A1 B5 N B1 A N N N A5 B1 B5 A5 B3 A1

N A1

B3 A1 A1 B5 B1

A2

A3

A2

A5 N

N N N N

N N A4

B3 B3 B5 A B2 N B3

B3 N A3

A1 A A

A5 N B5

N N N

A5 N N A3 A5

A4

N N

A A1 A1 A B3 A5 A1 A5 B1 B1

A A A

A N N A3

N N

N N

A5 N

A5 B1 A1

A A1

A5 B5 A5

A1 A1

A3 A3 A

A1 A1

A5

A5

A2 A2

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-19

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Phosgene Liquid Phosphate Slurry Phosphoric Acid Phosphoric Acid Phosphoric Anhydride Phosphorus Phosphorus Pentoxide Phosphorus Oxychloride Phosphorus Pentachloride Phosphorus Trichloride Photographic Solutions Phthalic Acid Phthalic Anhydride Picric Acid Polyvinyl Acetate Potassium Aluminum Chloride Potassium Aluminum Sulfate Potassium Aluminum Sulfate Potassium Bicarbonate Potassium Bicarbonate Potassium Borate Potassium Bromate Potassium Bromide Potassium Carbonate Potassium Chlorate, Aqueous

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

100% 100% 30% 85% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%

A1 A A1 A1 A1 A1 A1 A1

A3

A1 A A1 A1 A1 A1 A1 A1 A5 N A3 N A5 A4 A5

B2 N B3 B1 B3 A5 B5 N

A A4 A3

B1 A A1 A1 A5 B1 B5 B1

A1 A

A C5 C5

A1 A1

A A2

A2 A3 A

A4 N B3

A2 A2 N A5

A1 A1 A1 A1 A1 A1

A1

A1 A1 N

N A3 A3 A4 A3 A3 N A4

A5 A1 A1 A1 B1 A3

B5

A1 A5

A5 B5

A3 A3 A5 A1 A

A1 A1 A1 A1

B1 A1 B1

B1 B1 B3 B5

A1

A5

A5

50%

100%

A1

A1

A4

B5

A5

A3

A3

30% 100% 100% 100% 30% 50% 30%

A1 A A1 A1 A1 A1 A1

A1 A A1 A1 A1 A1 A1

A1 A A1 A1 A1 A1 A1

A3 B

B3 B

B5 A A

A3

A4 A4 A4 A3 A5 A4 A4 B1 A3 A1 B5 B3 B3 A5 B1 B5 A2 A2 A3 A3 A3

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-20

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Potassium Chloride Potassium Chloride Potassium Chloride Potassium Chromate Potassium Cyanide Potassium Dichromate Potassium Dichromate Potassium Ferricyanide Potassium Ferrocyanide Potassium Fluoride Potassium Hydroxide (Caustic Potash) Potassium Hydroxide (Caustic Potash) Potassium Hypochlorite Potassium Hypochlorite Potassium Nitrate Potassium Nitrite Potassium Perborate Potassium Perchlorate Potassium Permanganate Potassium Permanganate Potassium Persulfate Potassium Persulfate Potassium Sulfate

Maximum Concentration

PTFE

ETFE

30% 60% 100% 30% 30% 30% 60% 30% 30% 100% 10%

A1 A A A1 A1 A1 A A1 A1 A1 B

A1

A1 A

A4

A4

A1 B N A B3 B3 B3 B N N

A1 A A B5 A5 A1 A A5 B3 B5 N N

A A A

A3 B A A3

A A1 A1 A1

A A1 A1 A1 A A1

A A5 A3 A4 N

N B1 B3 A1 A N N N B3 B

A2 A A2 N N

N A3 A A5 A5 N

N N

N A A2 A3

A1 A1

A1 A1 A N

A1

50%

A1

A3

A1

A3

A5

B1

B1

A1

A3

40% 100% 80% 100% 100% 100% 10% 100% 10% 100% 10%

A A1 A1 A1 A1 A1 A1 N A A1 A1 A4 A1 A1 A1

A A1 A1 A1 A1 A1 A1 N A A1 A1

N B5

B B3 B3 N

B B3 B1 A A A

A3

A4

B1 N

A3 B3

A1 A3 A1 A

B1 A5 N B1 N A A4 A5 A3 A4 B1 A1 A5 N N N A3 B3 A A A A5 A2 A2 A A A1 A5 B5 A A

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-21

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Potassium Sulfate Potassium Sulfate Potassium Sulfide Potassium Sulfide Propane Propionic Acid Propyl Alcohol Propylene Chlorohydrin Propylene Dibromide Propylene Dichloride Propylene Glycol Propylene Oxide Pyridine Pyrogallol Salicyalldehyde Salicylic Acid Salt Brine Sea Water Sewage, Raw Silicon Tetrachloride Silver Chloride Silver Cyanide Silver Nitrate Silver Nitrate Sludge, Activated Sludge, Primary Sludge, Thickened Sludge, Waste Soap Solutions Sodium Acetate Sodium Benzene-Sulfon ate Sodium Benzoate

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

20% 100% 10% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 50% 100% 100% 100% 100% 100% 100% 100% 100%

A A A A1 A1 A1 A1 A1 A1 A3 A3 A

A A A A1 A1 A1 A1

N N

A A

A A B

A A

A A B

A1 A

A A A A5 B5

A5 A5 N A3 N A4

B3 B1 B3 A1

B5 B5 A1 A5

A5 B5 A1 B5

A5

A A1 A1 A1 A1 A1 A1 A1 A A A3 A1 A1 A1 A1 A1 A1 A1 A A N A5 N N B3 N N B1 B2 B1 N A B5 B5 A4 B2 A1 A A A5 B1 A2 A5 B2

A4 A4 A4 A3 A1 A A A

N N N

A5 A N

A5

B3 A A

A2 A A

A5 A A

A1 A1 A A1 A A A A A1 A1

A1 A1 A1

A1 A1 A A1 A A A A A1 A1

A3 A5 N N A A A5 N A3 A A A A A3 A3 A4

N A5 A5 N A A A A B5 B1

A5 A5 A A A A A5

A5 A5 A1 A A A A A A5 A5

A A A A A A A1

A5 A5 A5 A A A A A A5 A2

A4

A1 A

100%

A1

A1

A1

B5

A5

A5

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-22

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Sodium Bicarbonate Sodium Bicarbonate Sodium Bisulfate Sodium Bisulfate Sodium Bisulfide Sodium Bisulfite Sodium Bisulfite Sodium Borate (Borax) Sodium Boric Acid Sodium Bromide Sodium Carbonate Sodium Carbonate Sodium Carbonate Sodium Chloride Sodium Chlorate Sodium Chlorate Sodium Chloride Sodium Chlorite Sodium Chlorite Sodium Chromate Sodium Cyanide Sodium Dichromate Sodium Ferricyanide Sodium Ferrocyanide Sodium Fluoride Sodium Glutamate Sodium Hydrosulfite Sodium Hydroxide Sodium Hydroxide Sodium Hydroxide

Maximum Concentration

PTFE

ETFE

20% 100% 40% 100% 100% 40% 100% 100% 100% 100% 10% 20% 100% Sat 40% 100% 30% 10% 100% 80% 100% 100% 100% 100% 100% 100% 100% 5% 10% 25%

A1 A A A1 A A A1 A1 A A1 A A A1 A1 A A1 A A A1 A1 A1 A1 A1 A1 A1

A1 A A A1

A1 A A A1 A A A1 A1 A N

A3 A A A3

A4

A1 B N N N B2 B1 B3 N B N N B B2 B3 B3 N

A4 A A A A B5 A5 A B1 A2 A2

A A A2 A A A2 A5 A A A A2 A2 A2

A3 A

A4

A B2 A5

A1 A3

A3 A3

A4 A4

A3

A1 A A

A5 A

A A

A A B3 A B B2 B N A3 B5 A5 A3 B B3

B5 A A A3 A3 A A3 A

A1 A1 A1

A1 A1 A A1 A A A1 A1 A1 A1 A1 A1 A1 A5 N

A3 A3 A A5 A

A3 A5 A4

B1 N B N B1 N N A3 A1 B5 B1 B5

A3 A5 A3 N N A3

A1 A1 A3 A1 A1 A1 A

A1 A N A A A1 A B2 A5 A5 A5 N

A2 A A B B A N

A A5

A4

A4

A5

A1 A1 A1 A A3

A1 A1 A1 A N A5 N N A3 N A4

B A A1 N

A5

A5 N

A A A A3 A A

B2 A

N N

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-23

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Sodium Hydroxide Sodium Hydroxide Sodium Hydroxide Sodium Hypochlorite Sodium Hypochlorite Sodium Hypochlorite Sodium Hypochlorite Sodium Hyposulfite Sodium Iodide Sodium Lignosulfonate Sodium Metasilicate Sodium Methane Sodium Nitrate Sodium Nitrate Sodium Nitrate Sodium Nitrite Sodium Nitrite Sodium Perborate Sodium Perchlorate Sodium Peroxide Sodium Persulfate Sodium Phosphate (Mono-Basic) Sodium Phosphate (Tri-Basic) Sodium Silicate Sodium Silicofluoride Sodium Sulfate Sodium Sulfate Sodium Sulfate Sodium Sulfide

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

30% 40% 50% Conc 15% 20% 25% 5% 100% 100% 100% 100% 40% 50% 100% 40% 100% 10% 100% 10% 100% 100%

A1 A A1 A1 A A1 A1 A1 A1

A2

A1 A

A5

A3

A4

A4 B

B3 A A3

N N N B1

A A A

A3 A A5

A2 A1

A1 A1 A

A5 N

A3 N

A4 A5

A4

N N N A5 N N N A4

B N B A5

B B1 B A5 B5

A2 A2 A2

B B3 B

A1

A1 A1

A1 A1 A A

A1 A1

A A A A1 A A1 A1

A1 A1 A3 A

A A A A1 A A1 A1

N A5

A A3 A4 A3 A4

A N B2 N B1

A4

B N B2 N B3

A A B1 A B3

A2 A2 A2 A A

A A A5 A A3

A2 A1 A3 A4 B1 B3 A2

A1

A1 A A

A5

A2

A2

100%

A1

A1

A1

A4

A4

B3

B3

B2

A2

B3

100% 100% 20% 30% 100% 10%

A1

A1 A

A1

A3

A3

B1

B3

B1

A2

A3

A A A1 A1

A1 A1

A A A1 A1

N A5

A A3 A3

A4 A4

B A1 B2

B B B3 B2

A1 A B2

A2 A2 A2

A2 B B2

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-24

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Sodium Sulfide Sodium Sulfide Sodium Sulfite Sodium Sulfite Sodium Sulfite Sodium Tetraboric Acid Sodium Thiosulfate (Hypo) Sorbic Acid Sour Crude Oil Stannic Chloride Stannous Chloride Stannous Fluoride Stearic Acid Stoddards Solvent Styrene Monomer Succinic Acid Sulfamic Acid Sugar Juice Sulfinol Sulfolane Sulfur Dioxide (Wet) Sulfur Trioxide Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid Sulfuric Acid (Fuming) Sulfurous Acid Tall Oil Tannic Acid Tartaric Acid

Maximum Concentration

PTFE

ETFE

50% 100% 10% 30% 100% 100% 100%

A1 A A1 A A A A1

A1 A A1 A

A1 A A1 A A A A1 A5

A3 N A3 N

A4 A4

B3 N A3 B B B B1

B3 N N N N B B5

A A A

A2 A A2 A2 A A A2

A A

A1

A3

A4

100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 10% 30% 50% 60% 70% 80% 90% 95% 98% 100% 100% 100% 100% 100% 100%

A1 A1 A1

A A1 A1 A1 A

A1 A1 A1

A5 A3 A4 A4 A4 N

A4 B3 B1 B3 A A2 A5

A1 A1

A1 A1

A1 A1

A5

A3 N

N N A

A1 B5

A1 A5

B1

A1

A1

A1 A1 A

A1 A3

A1 A1 A

B3 N A4 N A4 A

B3 A

B1 B1 A

A1 A3 A

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

A2 A5 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A5 A2 A1 A1 A1

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1

N N A3 A3 A3 A3 A3 N N N N N N N N A3 A3

N A4 A4 A4 A5 N N N N N N N

B4 B1 N N N N N B5 B5 B3 B3 B3 A5 A5 B1 B3 A1

A4 B1 A3 A5 A5 A1 B3 A5 A4 A4 A5 A5 B5 B1 A1 N B3

B1 N B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 N A1 B1 B3

A1

N N N N N N N N

N N N N N N N N N N

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A2 A2 A2

N N N A4

N N A5 A4

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-25

Technical Data Sheet

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Maximum Concentration

00816-0100-3033, Rev CA Catalog 2008 - 2009

Process Liquid Tetraethyl Lead Tetrahydrofuran Tetramethyl Ammonium Hydroxide Thionyl Chloride Tin Chloride Tin Tetrachloride Titanium Dioxide Titamium Tetrachloride Toluene Tomato Juice Tributyl Phosphate Trichloroacetic Acid Trichlorethylene Trichloromethan e Triethanolamine Triethylamine Triethyl Phosphate Triphenyl Phosphite Trisodium Phosphate Turpentine Urea Varsol Vinegar Vinyl Acetate Vinyl Chloride (Monomer) Water (Pure) Water, Clean or Dirty Water, Deionized Water, Fresh Water, Salt Water, Sea Water Sewage

PTFE

ETFE

Tantalum

Platinum-10% Iridium

Titanium

100% 100% 50%

A1 A1 A1

A1 A3 A3

A1 A1 A1

B1 B1

A5

B3

100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 50% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%

A1 A1 A A1 A1 A1 A1 A1 A1

A3 A A A2 A1 A3 A4 A3 A1 A A4 A2

A1 A1 A A1 A1 A1 A1 A1 A1 A

N A3 A N N A3 N N N

N A4

N B4 A B5 A1 B1 B5 N B1

B1 A B5 A3 B5 B5 B3 A3

B1 A5 A A5 A1 A5 A A A1 A3

N N N N N

A2

A5 N

B1 B3

N A3

A1 A1

A1 A1

A4

A5

B5 B5

B3

B3 A3

A1

A1 A1 A1 A1 A1

A1 A1 A1 A A3 A1 A A

A1 A1 A1 A1 A1

A5 N N N

A3 N A4 A3 A5

A4 N A4 A4 A3 B3 B3 A4 B5

B5 B5

A A1 B5 A3 A5 A1

B5 A1

A5

A A1 A1 A1

A1 A1 A1

A A1 A1 A1

A N A5

A A3 A3 A4

A4

A B1 B1 B5

A A1 A1

A A5 A5 A5

A A5 A3 A5

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-26

Technical Data Sheet


00816-0100-3033, Rev CA Catalog 2008 - 2009

Magnetic Flowmeter
Flowtube Liner Electrode Material PFA Polyur ethane Linatex Neoprene Rubber 316 SST Hastelloy C-276 Tantalum Platinum-10% Iridium Titanium

Process Liquid Wax White Liquor Xylene Zinc Acetate Zinc Chloride Zinc Chloride Zinc Chloride Zinc Hydrosulfite Zinc Sulfate Zinc Sulfide Zinc Sulfate

Maximum Concentration

PTFE

ETFE

100% 100% 100% 100% 20% 50% 100% 10% Sat 100% 50%

A A1 A1 A A A1 A1 A A1 A A A1 A A1 A A1 A1 A1 A A A1 A1 A N N N A4 N A A4 N N A4 A4 A4 A4 A4 N N B5 B3 B3 N N A2 B3 B5 A1 B1 N B1 A2 B3 N A3 A2 A A3 A5 A5 A A1 A2 A2 A A2 A A3 A3 A3

A5 A5

Legend

Liners A = Resistant N = Not Resistant Blank =No Information Miscellaneous Sat = Saturated Conc = Concentrated

Electrodes (Corrosion Rate per Year) A = Less than 0.002 inches B = Less than 0.020 inches C = Less than 0.050 inches N = Greater than 0.050 inches Blank = No information

Temperatures 1 = 248F (120 C) 2 = 212F (100 C) 3 = 176F (80 C) 4 = 140F (60 C) 5 = 68F (20 C)

Flow-27

Technical Data Sheet

Magnetic Flowmeter

00816-0100-3033, Rev CA Catalog 2008 - 2009

Standard Terms and Conditions of Sale can be found at www.rosemount.com\terms_of_sale The Emerson logo is a trade mark and service mark of Emerson Electric Co. Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc. PlantWeb is a registered trademark of one of the Emerson Process Management group of companies. All other marks are the property of their respective owners.

Emerson Process Management Rosemoun Inc. 8200 Market Boulevard Chanhassen, MN 55317 USA T (U.S.) 1-800-999-9307 T (International) (952) 906-8888 F (952) 949-7001 www.rosemount.com Emerson Process Management Heath Place Bognor Regis West Sussex PO22 9SH England T 44 (0) 1243 863121 F 44 (0) 1243 867554 Emerson Process Management Singapore Pte Ltd. 1 Pandan Crescent Singapore 128461 Tel (65) 777-8211 Fax (65) 777-0947 Enquiries@AP.EmersonProcess.com

00816-0100-3033-
2008 Rosemount Inc. All rights reserved.

Vous aimerez peut-être aussi