Académique Documents
Professionnel Documents
Culture Documents
B1800/51 SHORT IN D SQUIB CIRCUIT B1801/51 OPEN IN D SQUIB CIRCUIT B1802/51 SHORT IN D SQUIB CIRCUIT (TO GROUND) B1803/51 SHORT IN D SQUIB CIRCUIT (TO B+)
CIRCUIT DESCRIPTION
The D squib circuit consists of the airbag sensor assy center, the spiral cable subassy and the horn button assy. The circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are recorded when a malfunction is detected in the D squib circuit.
DTC No. DTC Detecting Condition S The airbag sensor assy center receives a line short circuit signal 5 times in the D squib circuit during primary check. Trouble Area S Horn button assy (D squib) S Spiral cable subassy S Airbag sensor assy center S Instrument panel wire S Horn button assy (D squib) S Spiral cable subassy S Airbag sensor assy center S Instrument panel wire S Horn button assy (D squib) S Spiral cable subassy S Airbag sensor assy center S Instrument panel wire S Horn button assy (D squib) S Spiral cable subassy S Airbag sensor assy center S Instrument panel wire
B1800/51
B1801/51
S The airbag sensor assy center receives an open circuit signal in the D squib circuit for 2 seconds.
B1802/51
S The airbag sensor assy center receives a short circuit to ground signal in the D squib circuit for 0.5 seconds.
B1803/51
S The airbag sensor assy center receives a B+ short circuit signal in the D squib circuit for 0.5 seconds.
Author :
Date :
845
05683
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
WIRING DIAGRAM
D Squib YB 1 5 A12 D+
6 A12 D
H01451
Author :
Date :
846
05684
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
INSPECTION PROCEDURE
CAUTION: Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag deployment. (a) Turn the ignition switch to the LOCK position. (b) Disconnect the negative () terminal cable from the battery, and wait for at least 90 seconds. (c) Disconnect the connectors from the airbag sensor assy center. (d) Disconnect the connectors from the horn button assy. (e) Disconnect the connectors from the front passenger airbag assy. (f) Disconnect the connector from the instrument panel airbag assy lower No.1. (g) w/ Side and curtain shield airbag: Disconnect the connector from the front seat airbag assy LH. (h) w/ Side and curtain shield airbag: Disconnect the connector from the front seat airbag assy RH. (i) w/ Side and curtain shield airbag: Disconnect the connector from the curtain shield airbag assy LH. (j) w/ Side and curtain shield airbag: Disconnect the connector from the curtain shield airbag assy RH. (k) Disconnect the connector from the front seat outer belt assy LH. (l) Disconnect the connector from the front seat outer belt assy RH.
1
(a)
(2)
If not using the handheld tester (read the 2digit of DTC): Check the DTC (see page 05619). Result:
DTC 51 is output. E
B C D E A
Author :
Date :
847
05685
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
2
(a)
CHECK CONNECTOR
Check that the spiral cable subassy connectors (on the horn button assy side) are not damaged. OK: The lock button is not disengaged, or the claw of the lock is not deformed or damaged. NG REPLACE SPIRAL CABLE SUBASSY (SEE PAGE 6030)
OK
D Squib F E
DC
(b)
D+ Color: Orange
H41439
H43064
NG
Go to step NO TAG
OK GO TO STEP 10
Author :
Date :
848
05686
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
D Squib
Spiral Cable Subassy
F E
DC
D+ Color: Orange
H41439
H43064
NG
Go to step NO TAG
OK GO TO STEP 11
D Squib F E
DC
D+ Color: Orange
H41439
H43064
NG
Go to step NO TAG
OK GO TO STEP 11
Author :
Date :
849
05687
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
D Squib F E
DC
(b) (c)
D+ Color: Orange
H41439
H43064
NG
Go to step NO TAG
OK GO TO STEP 11
Author :
Date :
850
05688
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
7
(a)
CHECK CONNECTOR
Check that the spiral cable subassy connectors (on the horn button assy side) are not damaged. OK: The lock button is not disengaged, or the claw of the lock is not deformed or damaged. NG REPLACE SPIRAL CABLE SUBASSY (SEE PAGE 6030)
OK
D Squib F E
DC
(b) (c)
D+ Color: Orange
H41439
H43064
Turn the ignition switch to the LOCK position. Disconnect the negative () terminal cable from the battery, and wait for at least 90 seconds. Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ D Condition Always Specified condition Below 1
(g)
Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ Body ground D Body ground Condition Always Always Specified condition 1 M or Higher 1 M or Higher
(h) (i)
Release the activation prevention mechanism built into connector B (see page 05614). Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ D Condition Always Specified condition 1 M or Higher
NG OK
Go to step NO TAG
Author :
Date :
851
05689
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
D Squib FE
DC
DLC3
DTC 51
CG
TC
H43386
HINT: Perform the inspection using parts from a normal vehicle if possible. (b) Connect the connectors to the airbag sensor assy center. (c) Connect the negative () terminal cable to the battery, and wait for at least 2 seconds. (d) Turn the ignition switch to the ON position, and wait for at least 60 seconds. (e) Clear the DTCs stored in memory (see page 05619). (f) Turn the ignition switch to the LOCK position. (g) Turn the ignition switch to the ON position, and wait for at least 60 seconds. (h) Check the DTCs (see page 05619). OK: DTC 51 is not output. HINT: Codes other than code 51 may be output at this time, but they are not related to this check. NG REPLACE AIR BAG SENSOR ASSY CENTER (SEE PAGE 6063)
OK END
Author :
Date :
852
05690
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
10
D Squib F E
DC
H01002
H44386
HINT: Codes other than code B1800 may be output at this time, but they are not related to this check. NG REPLACE AIR BAG SENSOR ASSY CENTER (SEE PAGE 6063)
OK GO TO STEP 12
Author :
Date :
853
05691
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
11
D Squib F E
DC
H01002 C91348
H44390
OK
Author :
Date :
854
05692
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
12
D Squib
FE
DC
H01003
HINT: Codes other than code B1800, B1801, B1802 or B1803 may be output at this time, but they are not related to this check. NG REPLACE HORN BUTTON ASSY (SEE PAGE 6021)
Before performing the simulation method, check that the airbag sensor assy center is in check mode (see page 05622). Perform the simulation method by selecting the check mode with the handheld tester (see page 05622). After selecting the check mode, perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (see page 05622).
Author :
Date :
855
05693
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
13
Instrument Panel Wire Airbag D Squib Spiral Sensor A Cable Assy F E Subassy D C B Center A16
HINT: The activation prevention mechanism of connector B has already been released. (b) Measure the resistance according to the value(s) in the table below. Standard:
Tester connection Condition Always Specified condition 1 M or Higher A161 (D+) A162 (D)
D+
D
H41440 H43066
NG
OK
14
(b)
D Squib F E
Release the activation prevention mechanism built into connector D (see page 05614). Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ D Condition Always Specified condition 1 M or higher
D C
D+ Color: Orange
H41441
H43065
NG
Before performing the simulation method, check that the airbag sensor assy center is in check mode (see page 05622). Perform the simulation method by selecting the check mode with the handheld tester (see page 05622). After selecting the check mode, perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (see page 05622).
Author :
Date :
856
05694
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
15
Instrument Panel Wire Airbag D Squib Spiral Sensor Cable A Assy Subassy F E D C B Center A16
D+
D
H41440 H43066
NG
OK
16
D Squib F E
Spiral Cable Subassy
D C
D+ Color: Orange
H41441
H43065
NG
Before performing the simulation method, check that the airbag sensor assy center is in check mode (see page 05622). Perform the simulation method by selecting the check mode with the handheld tester (see page 05622). After selecting the check mode, perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (see page 05622).
Author :
Date :
857
05695
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
17
Instrument Panel Wire Airbag D Squib Spiral Sensor A Cable Assy F E Subassy D C B Center A16
D+
D
H41440 H43066
NG
OK
18
Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ Body ground D Body ground Condition Always Always Specified condition 1 M or Higher 1 M or Higher
D Squib F E
D C
D+ Color: Orange
H41441
H43065
NG
Before performing the simulation method, check that the airbag sensor assy center is in check mode (see page 05622). Perform the simulation method by selecting the check mode with the handheld tester (see page 05622). After selecting the check mode, perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (see page 05622).
Author :
Date :
858
05696
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
19
Instrument Panel Wire Airbag D Squib Spiral Sensor A Cable Assy F E Subassy D C B Center
(e) (f)
D+
Turn the ignition switch to the LOCK position. Disconnect the negative () terminal cable from the battery, and wait for at least 90 seconds. Disconnect the instrument panel wire connector from the spiral cable subassy. Connect the negative () terminal cable to the battery, and wait for at least 2 seconds. Turn the ignition switch to the ON position. Measure the voltage according to the value(s) in the table below. Standard:
Tester connection Condition Ignition switch ON Ignition switch ON Specified condition Below 1 V Below 1 V A161 (D+) Body ground A162 (D) Body ground
D
H41440 H43066
NG
OK
Author :
Date :
859
05697
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
20
Measure the voltage according to the value(s) in the table below when the ignition switch is in the ON position. Standard:
Tester connection D+ Body ground D Body ground Condition Ignition switch ON Ignition switch ON Specified condition Below 1 V Below 1 V
D Squib F E
D C
D+ Color: Orange
NG
H41441 H43065
Before performing the simulation method, check that the airbag sensor assy center is in check mode (see page 05622). Perform the simulation method by selecting the check mode with the handheld tester (see page 05622). After selecting the check mode, perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (see page 05622).
Author :
Date :
860
05698
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
21
Instrument Panel Wire Airbag D Squib Spiral Sensor Cable A Assy Subassy F E D C B Center A16
Restore the released activation prevention mechanism of connector B to the original condition. Disconnect the instrument panel wire connector from the spiral cable subassy. Connect the negative () terminal cable to the battery, and wait for at least 2 seconds. Turn the ignition switch to the ON position. Measure the voltage according to the value(s) in the table below. Standard:
Tester connection A161 (D+) Body ground Condition Ignition switch ON Ignition switch ON Specified condition Below 1 V Below 1 V
D
H41440 H43066
Turn the ignition switch to the LOCK position. Disconnect the negative () terminal cable from the battery, and wait for at least 90 seconds. Measure the resistance according to the value(s) in the table below. Standard:
Tester connection Condition Always Specified condition Below 1
(i)
Measure the resistance according to the value(s) in the table below. Standard:
Tester connection A161 (D+) Body ground A162 (D) Body ground Condition Always Always Specified condition 1 M or Higher 1 M or Higher
(j) (k)
Release the activation prevention mechanism built into connector B (see page 05614). Measure the resistance according to the value(s) in the table below. Standard:
Tester connection Condition Always Specified condition 1 M or Higher
NG
OK
Author :
Date :
861
05699
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
22
D Squib F E
Spiral Cable Subassy
D C
(b) (c)
D+ Color: Orange
H41441
H43065
Turn the ignition switch to the LOCK position. Disconnect the negative () terminal cable from the battery, and wait for at least 90 seconds. Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ D Condition Always Specified condition Below 1
(g)
Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ Body ground D Body ground Condition Always Always Specified condition 1 M or Higher 1 M or Higher
(h) (i)
Release the activation prevention mechanism built into connector D (see page 05614). Measure the resistance according to the value(s) in the table below. Standard:
Tester connection D+ D Condition Always Specified condition 1 M or higher
NG
Before performing the simulation method, check that the airbag sensor assy center is in check mode (see page 05622). Perform the simulation method by selecting the check mode with the handheld tester (see page 05622). After selecting the check mode, perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (see page 05622).
Author :
Date :
862