Académique Documents
Professionnel Documents
Culture Documents
Cylinders series "XL" comply with ISO 1 5552 standard, being in this way completely interchangeable with the former cylinders to ISO 6431 /VDMA 24562 standards. These cylinders are supplied cushioned as standard and, in the version with magnetic piston type can be supplied with magnetic sensors. Available also to directive 94/9/EC ("ATEX" - 2GD category).
Operating pressure Working temprerature Fluid Versions
series
DESCRIPTION
XL
1
TECHNICAL DATA
Bore Port size Standard strokes (mm) Decelerators lenght (mm) Maximum stroke (mm) Max. stroke single acting (mm)
1 1 0 bar 0 +80C (-30C with dry air) 0 +1 50C with seals for high temperatures (-1 0C with dry air) Filtered, unlubricated or continuous lubricated compressed air Double acting; Single acting front spring; Single acting rear spring; Through rod; Double push tandem; Double stroke tandem; Opposed tandem 1 25, 1 60, 200, 250, 320 1 25 = G 1 /2 1 60 - 200 = G 3/4 250 - 320 = G 1 25, 50, 75, 80, 1 00, 1 25, 1 50, 1 60, 1 75, 200, 250, 300, 320, 350, 400, 450, 500, 550, 600, 650, 700, 800, 900, 1 000 1 25 1 60 200 250 320 mm 37 40 40 75 80 3000 1 00
Painted die-cast aluminium with chromate conversion coating Cylinder barrel Extruded profile, 20 m anodized aluminium alloy Tie rods, tie and rods nuts Steel Stainless steel (supplied upon request for tie rods and tie nuts) Piston rod C45 chromium-plated steel AISI 303 rolled stainless steel Piston rod bearing Bronze-Iron 20%, sintered, self-lubricating Decelerator ogives Aluminium alloy Piston Die-cast aluminium alloy with chromate conversion coating Sea ls Polyurethane and NBR rubber Viton (available only for 1 25 200)
End caps
MATERIALS
Bore Version Stroke Series Pistone type Option 1 Option 2 Option 3 Option 4 Special option
N.B.: Magnetic switch FM1 00-FM1 57 (see chapter magnetic sensors
from page1 .93 del CAT.08/EN)
Cylinder 1 25, double acting, 1 00 mm stroke, non-magnetic piston type, ATEX: 1 25/1 00 XL/N /EX Cylinder 320, through rod, stroke 1 50, magnetic piston type, stainless steel piston rod: 320R1 50 XL/M1
ORDER EXAMPLES
II 2GDc T6 0C<Ta<60C from 1 25 to 200 II 2GDc T5 T1 00C -20C<Ta<80C from 250 to 320 * Available only for 1 25 200 ** Available even with Viton seals just for applications where is needed a chemical compatibility; not available for high temperatures.
VERSION T Double push tandem * / Double acting S Single acting front spring * P Double stroke tandem * Y Single acting rear spring * V Opposed tandem * R Through rod PISTON TYPE N Non magnetic M Magnetic ** OPTION 1 Z Fit for piston rod locking unit (only 1 25) OPTION 2 1 Stainless steel piston rod and rod nut 3 Stainless steel piston rod and rod nut and Viton seals* 2 Viton seals* OPTION 3 5 Extruded profile barrel (only 1 25) OPTION 4 /EX complies with the ATEX directive
SEALS KIT
SPARE PARTS
Polyuretane and NBR rubber Through rod and polyuretane and NBR rubber Viton Through rod Viton
Cylinders series XL
1 .5
series
XL BASIC CYLINDER
XL
46 50 48 54 66
32 40 40 50 63
D KK* l l 2* l 8* O PL* SW* TG* VA* VD WB WH* Weight Increase (g) (g) every 1 0mm
M27X2 268 50 1 60 M36X2 31 0 60 1 80 M36X2 31 0 60 1 80 67 200 M 42 X2 82 220 M 48 X2
12 15 15 16 18 29 30 24 31 31 27 36 36 46 55 11 0 1 40 1 75 220 270 6 6 6 10 10 7 6 6 20 20 205 65 80 95 1 05 1 20 6475 1 0850 1 5075 28500 48400 1 26 21 0 290 380 620
STANDARDIZED DIMENSIONS
THROUGH ROD
1 .6
Cylinders series XL
series
XL
1
OPPOSED TANDEM
P.S.: Rod nut supplied as standard FIT FOR PISTON ROD LOCKING UNIT
Cylinders series XL
1 .7
series
D
1 25 1 60 200 250 320 60 65 75 90 11 0
XL
E MF
20 20 25 25 30 1 40 1 80 220 285 350 245 280 300 330 370
Accessories
H11 H13
16 18 22 26 33
FB
W
45 60 75 80 90
ZF Weight (g)
3750 6350 11 350 201 00 31 800
* NOT TO ISO 1 5552 STANDARD FOOT - STEEL - CPUI/PB (supplied with screws)
AB AH AT AU
1 25 1 60 200 250
H14 JS15
16 18 24 26 90 11 5 1 35 1 65
E
1 40 1 80 220 270
F
70 75 1 00 1 00
SA
250 300 320 400
8 10 12 14
45 60 70 75
1 25 1 60 200 250
JS14
90 11 5 1 35 1 65
TR
XA Weight (g)
270 320 345 430 1 090 11 88 3450 6600
FRONT FEMALE HINGE - NOT TO ISO 1 5552 STANDARD - ALUMINIUM - CPUI/CFA (supplied with screws)
CB CD
1 25 1 60 200 70 90 90
H9
25 30 30
E
1 40 1 80 220
FL
50 55 60
L
30 35 35
h14
1 30 1 70 1 70
UB Weight (g)
11 80 1 780 2900
1 .8
Cylinders series XL
Accessories
series
XL
1
CB CD H9
70 90 90 11 0 1 20 25 30 30 40 45
E
1 40 1 80 220 268 340
FL
50 55 60 70 80
L
30 35 35 59 65
L4
10 10 11
h14
1 30 1 70 1 70 200 220
UB
XD
1 25 1 60 200 250 320 275 31 5 335 375 420
PIVOT FOR REAR FEMALE HINGE (ALUMINIUM) - GALVANIZED STEEL - CPU/CPUI/SEC (STEEL) - GALVANIZED NITRIDED STEEL - CPU/CPUI/SEC AC
BU EK EL Weight f7 (g)
1 39 1 78 1 78 21 4 234 25 30 30 40 45 1 32 1 71 .5 1 71 .5 202 222 530 978 978 1 800 2500
CD
1 25 1 60 200 250 320
H9
25 30 30 40 45
E
1 40 1 80 220 268 340
EW FL
70 90 90 11 0 1 20 50 55 60 70 80
L
30 35 35 47 52
L4
10 10 11 11 15
XD
275 31 5 335 375 420
Cylinders series XL
1 .9
series
SQUARE JOINT
XL
70 90 90 70 97 1 05 60 88 90 94 11 8 1 22 1 24 1 56 1 62 275 31 5 335 826 2600 3250
Accessories
1 25 1 60 200
1 25 22,5 1 4 1 60 31 ,5 1 4 200 31 ,5 1 8
CG CP B3 CF E FM L1 0 L11
D10 d12
37 43 43 97 1 22 1 22 6.3 6.3 6.3
F7
30 35 35
1 40 50 1 80 55 220 60
1 25 1 60 200
NON-ROTATING PIVOT FOR NARROW REAR FEMALE HINGE - GALVANIZED NITRIDED STEEL - CPUI/SEC AT
d4 JK L8 ES L9 L5
1 25 1 60 200
H12 f7
6 6 6 30 35 35
36 41 41
94 11 9 11 9
9 9 9
11 0 1 35 1 35
G Weight (g)
7 7 7 606 974 974
1 .1 0
Cylinders series XL
Accessories
NARROW MALE HINGE WITH ARTICULATED HEAD (ISO 1 2240) (supplied with screws)
CX E
1 25 1 60 200
H7
30 35 35
EN MS EU
37 43 43 40 45 48 25 28 28
G
20 20 25
DL
50 55 60
1 40 1 80 220
1 25 1 60 200
L4
10 10 11
SQUARE JOINT WITH ARTICULATED HEAD (ISO 1 2240) - STEEL - CPUI/ASSS AC CA BQ CK EM G1 G2 G3 H6 JS15 H7 JS14 JS14
1 25 90 25 30 37 70 60 90 20
1 25
JS1 4
94
K1
1 24
INTERMEDIATE HINGE - STEEL - EXTRUDED TUBE WITH TIE RODS - CX/CPUI/CT (supplied with dowels)
32 25 25 1 60 1 55 1 27 1 63 2600 40 32 32 200 1 90 1 50 1 90 4300 40 32 32 250 240 1 63 207 7540 50 40 40 320 295 1 84 226 1 2920 70 50 50 400 370 21 2 248 25280 P.S.: - ADJUSTABLE POSITION (fixing through dowels) - FIXED POSITION (specifiy dimension "XV", fixed on cylinder with completed threaded and galvanized rods type "S6", see on page 0.1 2) ASSEMBLY (FIXED): CX/CPUI/CT/+cylinders series XL S6 type MF/CX/CPUI/CT 1 25 1 60 200 250 320
A B1 B2 C d1 d2 FN
F7 H13
14 18 22
XA
1 92 50 60 245-295 360 90
1 25 1 60 - 200 250
Weight (g)
2600 4300 25280
Cylinders series XL
1 .11
series
FEMALE PISTON ROD CLEVIS WITH PIN AND SNAP RING TO ISO 81 40 - STEEL - M27x2 M36x2
XL
F
48 60 70 82 30 35 40 50 70 80
Accessories
DA DB DE
M27X2 M36X2 M42X2 M48X2
b12
30 35 40 50
HA
54 72 84 96
HB
11 0 1 44 1 68 1 92
L
1 48 1 88 232 265
Weight (g)
21 00 3900 5300 7900
Type
FFP27X2 FFP36X2 FFP42X2 FFP48X2
DA DB DC DE F G HA HB L W
H7
30 35
25 37 51 11 0 1 45 41 1 7 28 43 56 1 25 1 65 50 1 6
Weight (g)
1 200 1 600
Type
FF27x2/SS FF36x2/SS
DI
CH
41 55 65 75
12 15 16 18
See chapter magnetic sensors from page 1 .93 of the general catalog (CAT.08/EN)
MAGNETIC SENSOR SERIES FM1 00 - FM1 57 FIXING BRACKETS
For 1 25 200 see chapter magnetic sensors from page 1 .93 of the general catalog (CAT.08/EN)
SENSOR FIXING BRACKETS - ALUMINIUM - SQ (supplied with adapter for magnetic sensors series FM1 00)
250 320
A
26 26
B
20.5 25.5
C
42 42
Type
SQ250/A SQ320/A
1 .1 2
Cylinders series XL
series
d b a
XT - X - XL
c
a) Piston seal for rear chamber; b) Piston seal for front chamber; c) Cushioning seal for rear chamber; d) Cushioning seal for front chamber; e) Rod seal.
APPLICATIONS
Rear chamber Rear chamber + cushioning Rear chamber + rod seals Rear chamber + cushioning + rod seals Front chamber Front chamber + cushioning
DESCRIPTION
DESCRIPTION
OPTION SA SB SC SD SE SF
SEALS
The low friction cylinders series "XT", "X" and "XL" (available from 1 25 to 200), are used as "dancers" or "enlager strechers" cylinders, but they are just single acting cylinders without the return spring. As indicated in the previous table, we can have different applications, combining properly the various seals inserted in the cylinder. The application called as option "SA" is the main one, because, using just the seal "a", it's the one that offers the lowest internal friction. The "SB" option uses the pneumatic cushioning for an emergency situation, to avoid crushes in the case of the breakdown of the plant. In the options "SC" and "SD", the rod seal avoids to the impurities to go into the cylinder. In the option "SE" the pressurized chamber is the front one and in the option "SF" the pressurized chamber is stil the front one but with the pneumatic cushioning for an emergency situation. ATTENTION: For the applications please consider the cylinder as single acting without spring. Cylinder 50, double acting, 1 00 mm stroke, magnetic piston type, rear chamber and cushioning seals:
ORDER EXAMPLE
50/1 00 XT/M SB
Cylinder 1 25, double acting, 200 mm stroke, magnetic piston type, front chamber and cushioning seals:
1 25/200 XL/M SF
1 .1 3