Académique Documents
Professionnel Documents
Culture Documents
1
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
THERMAL ENGINEERING AND HEAT TRANSFER
( Common to Mechatronics and Production Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) Derive an expression for the mean effective pressure of diesel cycle.
(b) The ideal Otto engine working on the air standard cycle has a temperature
and pressure at the beginning is 250 C and 1 bar respectively and a thermal
efficiency of 48%. Determine the pressure and temperature at the end of
compression. [8+8]
2. What is the effect of high sulphur content on the performance of S1 and C1 engine?
Discuss. [16]
5. (a) Sketch a line diagram of a semi-closed gas turbine cycle. Indicate its place of
operation.
(b) Discuss the relative advantages and disadvantages of reciprocating I.C.engines
and gas turbines. [8+8]
6. (a) Derive an expression for the overall coefficient of heat transfer based on the
inside area for the composite cylinder having two layers with fluid boundaries.
(b) A brick wall 25 cm thick is faced with concrete of 5 cm thick. The thermal
conductivity of the brick is 0.7 W/mK while that of the concrete is 0.9 W/mK.
If the temperature of the exposed brick face is 300 C and that of the concrete
is 50 C, find the heat loss per hour through a wall of 10 × 5m. [8+8]
7. The parallel outer and inner walls of a building are 4m high and 5m long. The
walls are 10 cm apart. The inner surface of the inner wall is at 250 C and the inner
surface of the outer wall is at 50 C.
8. (a) When a body is said to be black? What is the range of wave lengths it absorbs?
1 of 2
Code No: RR221403 Set No. 1
(b) Compute the radiant energy loss from 1 cm diameter opening in a thin walled
furnace located in a large enclosure, if the temperature with in the furnace is
9000 C and the surroundings are at 200 C. [6+10]
⋆⋆⋆⋆⋆
2 of 2
Code No: RR221403 Set No. 2
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
THERMAL ENGINEERING AND HEAT TRANSFER
( Common to Mechatronics and Production Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) Derive an expression for the mean effective pressure of diesel cycle.
(b) The ideal Otto engine working on the air standard cycle has a temperature
and pressure at the beginning is 250 C and 1 bar respectively and a thermal
efficiency of 48%. Determine the pressure and temperature at the end of
compression. [8+8]
4. (a) Define mean effective pressure and distinguish between brake mean effective
pressure and indicated mean effective pressure.
(b) How smoke density can be measured? Describe with sketch the principle of
Bosch or Hartridge smoke meter. [6+10]
5. (a) What are the desirable properties of fluid suitable for closed cycle operation?
Also explain the disadvantages of a closed cycle gas turbine over open cycle
gas turbine.
(b) Air enters the compressor of an open cycle constant pressure gas turbine at 1
bar and 300 C. The pressure of air after the compression is 4 bar. The isoen-
tropic efficiencies of compressor and turbine are 75% and 80% respectively.
The air fuel ratio used is 75%. Find the I.P and thermal efficiency of the cycle
if the flow rate of the air is 2.5kg/sec. Take Cp =1 kJ/kg and γ=1.4 for air
and gases. C.V of fuel used is 42000 kJ/kg. [8+8]
6. (a) What is the basic difference between conduction and radiation heat transfer
processes?
(b) Identify the modes of heat transfer in the following examples.
i. A car disc brake during braking
ii. A domestic boiler
iii. Heating a room using an electric fan heater
iv. Soldering an electric circuit board
1 of 2
Code No: RR221403 Set No. 2
v. Gas welding two sheets of steel plate. [6+10]
7. (a) Define Nusselt and Prandtl numbers. Explain their importance in convection
heat transfer.
(b) A vertical pipe 5 cm diameter carrying hot water is exposed to ambient air
at 150 C. If the outer surface of the pipe is 650 C, find the heat loss from one
metre height of the pipe per hour. [8+8]
8. (a) When a body is said to be black? What is the range of wave lengths it absorbs?
(b) Compute the radiant energy loss from 1 cm diameter opening in a thin walled
furnace located in a large enclosure, if the temperature with in the furnace is
9000 C and the surroundings are at 200 C. [6+10]
⋆⋆⋆⋆⋆
2 of 2
Code No: RR221403 Set No. 3
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
THERMAL ENGINEERING AND HEAT TRANSFER
( Common to Mechatronics and Production Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) Define
i. bore and stroke
ii. displacement and clearance volume.
(b) Discuss the merits and demerits of 2 stroke engines over 4 stroke engines.[8+8]
(a) Idling
(b) Maximum power
(c) Sudden acceleration [5+5+6]
5. An open cycle gas turbine plant consists of compressor, combustion chamber and
turbine. The pressure and temperature at the inlet of compressor are 1 bar and
150 C and at the inlet of the turbine are 5 bar and 6500 C. Assume ζe = 80%, ζt =
85%, ζm = 90% and ζcom =98%. Assuming Cpa = 1 KJ/kg K, Cpg = 1.2 kJ/kg K
and ν (for air) = 1.4 and r(for gases) = 1.334. Find
6. (a) What are different modes of heat transfer? Discuss the mechanism of conduc-
tion heat transfer in solids.
(b) Identify the various modes of heat transfer in the following cases.
i. Heat transfer from an auto radiator
ii. Condensation of steam in condenser
iii. Heat loss from a thermos flask
1 of 2
Code No: RR221403 Set No. 3
iv. Protection of human body with warm clothing in winter. [8+8]
⋆⋆⋆⋆⋆
2 of 2
Code No: RR221403 Set No. 4
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
THERMAL ENGINEERING AND HEAT TRANSFER
( Common to Mechatronics and Production Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) What do you mean by air standard cycles? What are the assumptions for air
standard cycles?
(b) Derive an equation for the air standard efficiency of an engine working on the
Otto cycle in terms of its compression ratio and ratio of specific heats of air.
[6+10]
2. What are the different kinds of fuels used in an IC engine? Discuss them in detail.
[16]
3. (a) What is the purpose of the fan radiator system? Is it required at all times?
Why?
(b) What is the effect of super charging on the following parameters:
i. Power output
ii. Mechanical efficiency
iii. Fuel consumption [4+12]
5. (a) Sketch a line diagram of a semi-closed gas turbine cycle. Indicate its place of
operation.
(b) Discuss the relative advantages and disadvantages of reciprocating I.C.engines
and gas turbines. [8+8]
6. Prove that the heat loss per square metre of outside surface area of a hollow sphere
heated from within is equal to
2k(T1 − T2 )
q = D2
(D2 − D1 ) D 1
where T1 and T2 are the temperatures and D1 and D2 are the diameters of the
inner and outer surfaces respectively. [16]
7. The parallel outer and inner walls of a building are 4m high and 5m long. The
walls are 10 cm apart. The inner surface of the inner wall is at 250 C and the inner
surface of the outer wall is at 50 C.
1 of 2
Code No: RR221403 Set No. 4
(b) If the air space is divided in half by a sheet of aluminium foil 0.025 mm thick
parallel to the walls, what would be the heat loss per hour. [16]
8. (a) What do you mean by ‘total emissive power’ ? State Stefan-Boltzman Law
and explain.
(b) The concentric spheres, 20 cm and 30 cm in diameter are used to store liquid
oxygen at -1530 C in a room at 3000 K. The space between spheres is evacuated.
The surfaces of the spheres are highly polished as E = 0.04. Find the rate
of evaporation of liquid oxygen per hour. Take latent heat of oxygen as 209
kJ/kg. [6+10]
⋆⋆⋆⋆⋆
2 of 2