Académique Documents
Professionnel Documents
Culture Documents
Micro-Star International
MS-7677
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Part Number
G52-76771X2
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no
guarantee is given as to the correctness of its contents. Our products are under
continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
Revision History
Revision
Revision History
Date
V1.0
First release
2011/03
V1.1
2011/04
MS-7677
Safety Instructions
Make sure the voltage of the power source is at 110/220V before connecting.
Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
Always Unplug the Power Cord before inserting any add-on card or module.
All cautions and warnings on the equipment should be noted.
Never pour any liquid into the opening that can cause damage or cause electrical shock.
If any of the following situations arises, get the equipment checked by service
personnel:
The equipment does not work well or you can not get it work according
to User Manual.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60C (140F), IT MAY DAMAGE THE EQUIPMENT.
CAUTION
Danger of explosion if battery is incorrectly replaced.
For better environmental protection, waste batteries should be collected separately for recycling or special disposal.
WEEE Statement
ENGLISH
To protect the global environment and as an environmentalist, MSI
must remind you that...
Under the European Union (EU) Directive on Waste Electrical and
Electronic Equipment, Directive 2002/96/EC, which takes effect on
August 13, 2005, products of electrical and electronic equipment
cannot be discarded as municipal wastes anymore, and manufacturers of covered
electronic equipment will be obligated to take back such products at the end of
their useful life. MSI will comply with the product take back requirements at the
end of life of MSI-branded products that are sold into the EU. You can return these
products to local collection points.
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt
Gem der Richtlinie 2002/96/EG ber Elektro- und Elektronik-Altgerte drfen
Elektro- und Elektronik-Altgerte nicht mehr als kommunale Abflle entsorgt
werden. MSI hat europaweit verschiedene Sammel- und Recyclingunternehmen
beauftragt, die in die Europische Union in Verkehr gebrachten Produkte, am
Ende seines Lebenszyklus zurckzunehmen. Bitte entsorgen Sie dieses Produkt
zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgertesammelstelle
in Ihrer Nhe.
FRANAIS
En tant qucologiste et afin de protger lenvironnement, MSI tient rappeler
ceci...
Au sujet de la directive europenne (EU) relative aux dchets des quipement
lectriques et lectroniques, directive 2002/96/EC, prenant effet le 13 aot 2005,
que les produits lectriques et lectroniques ne peuvent tre dposs dans les
dcharges ou tout simplement mis la poubelle. Les fabricants de ces quipements seront obligs de rcuprer certains produits en fin de vie. MSI prendra en
compte cette exigence relative au retour des produits en fin de vie au sein de la
communaut europenne. Par consquent vous pouvez retourner localement ces
matriels dans les points de collecte.
MSI
, , ....
()
( WEEE 2002/96/EC),
13 2005 , ,
, ,
. MSI
,
MSI EC, .
.
MS-7677
ESPAOL
MSI como empresa comprometida con la proteccin del medio ambiente,
recomienda:
Bajo la directiva 2002/96/EC de la Unin Europea en materia de desechos y/
o equipos electrnicos, con fecha de rigor desde el 13 de agosto de 2005, los
productos clasificados como elctricos y equipos electrnicos no pueden ser
depositados en los contenedores habituales de su municipio, los fabricantes de
equipos electrnicos, estn obligados a hacerse cargo de dichos productos al
termino de su perodo de vida. MSI estar comprometido con los trminos de
recogida de sus productos vendidos en la Unin Europea al final de su periodo
de vida. Usted debe depositar estos productos en el punto limpio establecido por
el ayuntamiento de su localidad o entregar a una empresa autorizada para la
recogida de estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan herinneren dat.
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en Electronische producten (2002/96/EC), die op 13 Augustus 2005 in
zal gaan kunnen niet meer beschouwd worden als vervuiling. Fabrikanten van dit
soort producten worden verplicht om producten retour te nemen aan het eind van
hun levenscyclus. MSI zal overeenkomstig de richtlijn handelen voor de producten
die de merknaam MSI dragen en verkocht zijn in de EU. Deze goederen kunnen
geretourneerd worden op lokale inzamelingspunten.
SRPSKI
Da bi zatitili prirodnu sredinu, i kao preduzee koje vodi rauna o okolini i prirodnoj sredini, MSI mora da vas podesti da
Po Direktivi Evropske unije (EU) o odbaenoj ekektronskoj i elektrinoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi
koji spadaju pod elektronsku i elektrinu opremu ne mogu vie biti odbaeni
kao obian otpad i proizvoai ove opreme bie prinueni da uzmu natrag ove
proizvode na kraju njihovog uobiajenog veka trajanja. MSI e potovati zahtev
o preuzimanju ovakvih proizvoda kojima je istekao vek trajanja, koji imaju MSI
oznaku i koji su prodati u EU. Ove proizvode moete vratiti na lokalnim mestima
za prikupljanje.
POLSKI
Aby chroni nasze rodowisko naturalne oraz jako firma dbajca o ekologi, MSI
przypomina, e...
Zgodnie z Dyrektyw Unii Europejskiej (UE) dotyczc odpadw produktw elektrycznych i elektronicznych (Dyrektywa 2002/96/EC), ktra wchodzi w ycie 13
sierpnia 2005, tzw. produkty oraz wyposaenie elektryczne i elektroniczne nie
mog by traktowane jako mieci komunalne, tak wic producenci tych produktw
bd zobowizani do odbierania ich w momencie gdy produkt jest wycofywany z
uycia. MSI wypeni wymagania UE, przyjmujc produkty (sprzedawane na terenie Unii Europejskiej) wycofywane z uycia. Produkty MSI bdzie mona zwraca
w wyznaczonych punktach zbiorczych.
TRKE
evreci zelliiyle bilinen MSI dnyada evreyi korumak iin hatrlatr:
Avrupa Birlii (AB) Kararnamesi Elektrik ve Elektronik Malzeme At, 2002/96/
EC Kararnamesi altnda 13 Austos 2005 tarihinden itibaren geerli olmak zere,
elektrikli ve elektronik malzemeler dier atklar gibi pe atlamayacak ve bu
elektonik cihazlarn reticileri, cihazlarn kullanm sreleri bittikten sonra rnleri
geri toplamakla ykml olacaktr. Avrupa Birliine satlan MSI markal rnlerin
kullanm sreleri bittiinde MSI rnlerin geri alnmas istei ile ibirlii ierisinde
olacaktr. rnlerinizi yerel toplama noktalarna brakabilirsiniz.
ESKY
Zle nm na ochran ivotnho prosted - spolenost MSI upozoruje...
Podle smrnice Evropsk unie (EU) o likvidaci elektrickch a elektronickch
vrobk 2002/96/EC platn od 13. srpna 2005 je zakzno likvidovat elektrick
a elektronick vrobky v bnm komunlnm odpadu a vrobci elektronickch vrobk, na kter se tato smrnice vztahuje, budou povinni odebrat takov
vrobky zpt po skonen jejich ivotnosti. Spolenost MSI spln poadavky na
odebrn vrobk znaky MSI, prodvanch v zemch EU, po skonen jejich
ivotnosti. Tyto vrobky mete odevzdat v mstnch sbrnch.
MAGYAR
Annak rdekben, hogy krnyezetnket megvdjk, illetve krnyezetvdknt
fellpve az MSI emlkezteti nt, hogy ...
Az Eurpai Uni (EU) 2005. augusztus 13-n hatlyba lp, az elektromos
s elektronikus berendezsek hulladkairl szl 2002/96/EK irnyelve szerint
az elektromos s elektronikus berendezsek tbb nem kezelhetek lakossgi
hulladkknt, s az ilyen elektronikus berendezsek gyrti kteless vlnak az
ilyen termkek visszavtelre azok hasznos lettartama vgn. Az MSI betartja
a termkvisszavtellel kapcsolatos kvetelmnyeket az MSI mrkanv alatt az
EU-n bell rtkestett termkek esetben, azok lettartamnak vgn. Az ilyen
termkeket a legkzelebbi gyjthelyre viheti.
ITALIANO
Per proteggere lambiente, MSI, da sempre amica della natura, ti ricorda che.
In base alla Direttiva dellUnione Europea (EU) sullo Smaltimento dei Materiali
Elettrici ed Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti alla categoria dei Materiali Elettrici ed Elettronici non possono pi
essere eliminati come rifiuti municipali: i produttori di detti materiali saranno obbligati a ritirare ogni prodotto alla fine del suo ciclo di vita. MSI si adeguer a tale
Direttiva ritirando tutti i prodotti marchiati MSI che sono stati venduti allinterno
dellUnione Europea alla fine del loro ciclo di vita. possibile portare i prodotti
nel pi vicino punto di raccolta
MS-7677
Table of Content
English............................................................................... 9
Getting startED..........................................................................................9
SPECIFICATIONS............................................................................................10
REAR PANEL...................................................................................................11
HARDWARE SETUP........................................................................................11
BIOS Setup....................................................................................................18
.................................................................................. 23
............................................................................................................23
...................................................................................................................24
...........................................................................................................25
...................................................................................................25
BIOS .........................................................................................................32
Franais.......................................................................... 37
Pour commencer.......................................................................................37
SPCIFICATIONS............................................................................................38
Panneau arrire.......................................................................................39
Installation du matriel.......................................................................39
Rglage bios...............................................................................................46
DEUTSCH........................................................................... 51
eINLEITUNG....................................................................................................51
SPEZIFIKATIONEN..........................................................................................52
Hinteres Anschlusspanel.....................................................................53
HARDWARE SETUP........................................................................................53
BIOS Setup....................................................................................................60
........................................................................... 65
..........................................................................................65
........................................................................................66
...........................................................................................67
.....................................................................67
BIOS..........................................................................................74
.............................................................................. 79
...................................................................................................................79
...................................................................................................................80
............................................................................................................81
............................................................................................................81
Setup ......................................................................................................88
.............................................................................. 93
...................................................................................................................93
...................................................................................................................94
...................................................................................................................95
............................................................................................................95
BIOS .......................................................................................................102
................................................................................ 107
..........................................................................................................107
........................................................................................108
I/O........................................................................................................109
.............................................................................109
BIOS.....................................................................................................116
MS-7677
English
Getting startED
Thank you for choosing the H61I-E35 (B3) series (MS-7677 v1.x) Mini-ITX mainboard. These series are designed based on Intel H61 (B3) chipset for optimal
system efficiency. Designed to fit the advanced Intel LGA1155 processor, these
series deliver a high performance and professional desktop platform solution.
Layout
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
SPECIFICATIONS
Processor Support
Intel Sandy Bridge processor in the LGA1155 package
(For the latest information about CPU, please visit
http://www.msi.com/service/cpu-support)
Chipset
Intel H61 (B3) chipset
Memory Support
2 DDR3 DIMMs support DDR3 1333/ 1066 SDRAM (total Max. 16GB)
Supports Dual-Channel mode
(For more information on compatible components, please visit
http://www.msi.com/service/test-report)
LAN
Supports LAN 10/ 100/ 1000 by Realtek 8111E
Audio
Chip integrated by Realtek ALC887
Supports 8 channels audio out
Compliant with Azalia 1.0 Spec
SATA
4 SATA 3Gb/s ports by Intel H61 (B3)
Connectors
Back panel
1 PS/2 mouse port
1 PS/2 keyboard port
1 VGA port*
1 HDMI port*
4 USB 2.0 ports
1 LAN jack
3 flexible audio jacks
*(The VGA and HDMI port only work with Integrated Graphics Processor.)
On-Board Connectors
2 USB 2.0 connectors
1 Front Panel Audio connector
1 TPM connector
1 S/PDIF-Out connector
Slots
1 PCIE x1 slot
Form Factor
Mini-ITX (17.0 cm X 17.0 cm)
Mounting
4 mounting holes
If you need to purchase accessories and request the part numbers, you could
search the product web page and find details on our web address below
http://www.msi.com/index.php
10
MS-7677
REAR PANEL
The rear panel provides the following connectors:
LAN
Mouse
VGA Port
Line-In
USB Ports
Line-Out
Keyboard
USB Ports
HDMI Port
MIC
Note: To reach the 8-channel sound effect, the 7th and 8th channels must be
output from front panel.
HARDWARE SETUP
This section provides instructions on CPU and memory installation, as well as
jumper settings on the mainboard. While doing the installation, be careful in holding the components and follow the installation procedures.
CPU & Cooler Installation Procedures for LGA1155
When you are installing the CPU, make sure that you install the cooler to prevent
overheating. If you do not have the CPU cooler, consult your dealer before turning
on the computer.
Introduction to LGA 1155 CPU
The figure below shows the surface of LGA 1155 CPU. Remember to apply some
thermal paste on it for better heat dispersion.
Important
Please use the boxed CPU fan or other enhanced coolers to maintain the system
stability.
Alignment Key
Alignment Key
11
Follow the steps below to install the CPU & cooler correctly. Wrong installation will cause the damage of your
CPU & mainboard.
.
2.
3.
4.
5.
6.
7.
Secure the lever near the hook end under the retention tab.
8.
9.
Align the holes on the mainboard with the heatsink. Push down the cooler until
its four clips get wedged into the holes of the mainboard.
Important
* Read the CPU status in BIOS.
* Whenever CPU is not installed, always protect your CPU socket pin with the
plastic cap covered to avoid damaging.
* Mainboard photos shown in this section are for demonstration of the CPU/ cooler installation only. The appearance of your mainboard may vary depending on
the model you purchase.
* Please refer to the documentation in the CPU fan package for more details
about the CPU fan installation.
12
MS-7677
Installing Memory Modules
. The memory module has only one notch on the center and will only fit in the
right orientation.
2.
Insert the memory module vertically into the DIMM slot. Then push it in until
the golden finger on the memory module is deeply inserted in the DIMM slot.
The plastic clip at each side of the DIMM slot will automatically close when the
memory module is properly seated. You can barely see the golden finger if the
memory module is properly inserted in the DIMM slot.
3.
Manually check if the memory module has been locked in place by the DIMM
slot clips at the sides.
Volt
Notch
Important
* In Dual-Channel mode, make sure that you install memory modules of the same
type and density in different channel DIMM slots.
* To enable successful system boot-up, always insert the memory modules into
the DIMM1 first.
13
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
Important
* Make sure that all the connectors are connected to proper ATX power supplies
to ensure stable operation of the mainboard.
* Power supply of 350 watts (and above) is highly recommended for system stability.
Important
Please do not fold the Serial ATA cable into a 90-degree angle. Otherwise, data
loss may occur during transmission.
14
MS-7677
Fan Power Connectors: CPUFAN, SYSFAN1
The fan power connectors support system cooling fan with +12V. When connecting the wire to the connectors, always note that the red wire is the positive and
should be connected to the +12V; the black wire is Ground and should be connected to GND. If the mainboard has a System Hardware Monitor chipset onboard, you must use a specially designed fan with speed sensor to take advantage
of the CPU fan control.
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
15
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
n
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
d
C un +
.N o 1
0 r B 11 .G
8 US B
. S
6 .U C
4 VC
.
2
in
P d
n
o u +
.N r o 0
9 .G SB 07 .U B
S
5 .U CC
3 .V
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
16
MS-7677
Clear CMOS Jumper: JBAT1
There is a CMOS RAM onboard that has a power supply from an external battery
to keep the data of system configuration. With the CMOS RAM, the system can
automatically boot OS every time it is turned on. If you want to clear the system
configuration, set the jumper to clear data.
JBAT1
1
Keep Data
Clear Data
Important
You can clear CMOS by shorting 1-2 pin while the system is off, then open it. Avoid
clearing the CMOS while the system is on; it will damage the mainboard.
17
BIOS Setup
Power on the computer and the system will start POST (Power On Self Test)
process. When the message below appears on the screen, press <DEL> key to
enter Setup.
Press DEL to enter Setup Menu
If the message disappears before you respond and you still wish to enter Setup,
restart the system by turning it OFF and On or pressing the RESET button. You
may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
The Menu Bar
Main Menu
Use this menu for basic system configurations, such as time, date etc.
Advanced
Use this menu to set up the items of special enhanced features.
Overclocking
Use this menu to specify the settings for DRAM timing and CPU features.
M-Flash
Use this menu to read/ flash the BIOS form storage drive (FAT/ FAT32 format
only).
Security
Use this menu to set supervisor and user passwords.
Boot
18
MS-7677
Use this menu to specify the priority of boot devices.
Save & Exit
This menu allows you to load the BIOS default values or factory default settings
into the BIOS and exit the BIOS setup utility with or without changes.
Overclocking
19
20
MS-7677
tWTR
Minimum time interval between the end of write data burst and the start of a
column-read command. It allows I/O gating to overdrive sense amplifiers before
read command starts.
tRRD
Specifies the active-to-active delay of different banks.
tRTP
Time interval between a read and a precharge command.
tFAW
This item is used to set the tFAW (four activate window delay) timing.
tWCL
This item is used to set the tWCL (Write CAS Latency) timing.
tCKE
This item is used to set the tCKE timing.
tRTL
This item is used to set the tRTL timing.
Advanced Channel 1/ 2 Timing Configuration
Press <Enter> to enter the sub-menu. And you can set the advanced memory
timing for each channel.
GT OverClocking
This item allows you to enable/ disable the overclocking of integrated graphics.
GT Ratio
This setting controls the ratio of integrated graphics frequency to enable the integrated graphics to run at different frequency combinations.
Adjusted GT Frequency
It shows the adjusted integrated graphics frequency. Read-only.
Spread Spectrum
When the mainboards clock generator pulses, the extreme values (spikes) of the
pulses create EMI (Electromagnetic Interference). The Spread Spectrum function
reduces the EMI generated by modulating the pulses so that the spikes of the
pulses are reduced to flatter curves.
Important
* If you do not have any EMI problem, leave the setting at [Disabled] for optimal
system stability and performance. But if you are plagued by EMI, select the
value of Spread Spectrum for EMI reduction.
* The greater the Spread Spectrum value is, the greater the EMI is reduced, and
the system will become less stable. For the most suitable Spread Spectrum
value, please consult your local EMI regulation.
* Remember to disable Spread Spectrum if you are overclocking because even a
slight jitter can introduce a temporary boost in clock speed which may just cause
your overclocked processor to lock up.
21
CPU Features
Press <Enter> to enter the sub-menu. In this sub-menu you can adjust the CPU
features.
Save & Exit
22
MS-7677
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
23
LGA1155 Intel Sandy Bridge .
(CPU
http://www.msi.com/service/cpu-support )
Realtek ALC887
8
Azalia 1.0 Spec
SATA
Intel H61 (B3) SATA 3Gb/s 4
PS/2 1
PS/2 1
VGA 1*
HDMI 1*
USB 2.0 4
LAN 1
3
*(VGA HDMI
.)
USB 2.0 2
1
TPM 1
S/PDIF 1
PCIE x1 1
Mini-ITX (17.0 cm X 17.0 cm)
,
http://www.msi.com/index.php .
24
MS-7677
.
LAN
VGA
USB
USB
HDMI
: 8 ,
.
CPU
. , .
LGA1155 CPU
. CPU
.
LGA 1155 CPU
LGA 1155 CPU .
.
CPU
.
1 .
25
CPU .
CPU .
.
2.
3.
CPU
. CPU ,
.
.
4.
CPU ,
CPU . CPU
.
.
5.
CPU
. , CPU
.
6.
7.
8.
4
.
9.
. 4
.
0. 4 .
. .
2. CPU CPU .
* BIOS CPU .
* CPU , CPU
.
* CPU/
. .
* CPU CPU
.
26
MS-7677
.
, .
2.
DIMM .
DIMM .
, DIMM
. DIMM
.
3.
DIMM
.
* , DIMM
.
* , DIMM1 .
27
ATX 24 : JPWR1
ATX 24 . ATX 24
,
, .
.
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
ATX 4 : JPWR2
4 CPU .
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
* ATX
.
* 350 watts ( ) .
ATA : SATA1 ~ 4
ATA .
ATA .
ATA 90 . ,
.
28
MS-7677
: CPUFAN, SYSFAN1
+12V .
, +12V ,
GND .
, CPU
.
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
S/PDIF : JSP1
S/PDIF(Sony & Philips Digital Interconnect Format) .
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
: JFP1
LED . JFP1
Intel Front Panel I/O Connectivity Design Guide .
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
29
: JAUD1
, Intel
Front Panel I/O Connectivity Design Guide .
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
d
C un +
.N o 1
0 r B 11 .G
8 US B
. S
6 .U C
4 VC
.
2
in
P d
n
o u +
.N r o 0
9 .G SB 07 .U B
S
5 .U CC
3 .V
1
TPM : JTPM1
TPM(Trusted Platform Module) .
TPM .
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
30
MS-7677
CMOS : JBAT1
CMOS RAM . CMOS RAM ,
OS . ,
.
JBAT1
1
1-2 CMOS .
1-2 . CMOS .
.
PCI Express
PCI Express PCI Express .
PCI Express x1 .
31
BIOS
POST(Power On Self Test) .
, <DEL> .
Press DEL to enter Setup Menu
,
(RESET) . <Ctrl>, <Alt>
<Delete> .
Main Menu
, .
Advanced
.
Overclocking
DRAM CPU .
M-Flash
BIOS (FAT/
FAT32 ).
Security
.
Boot
.
32
MS-7677
Save & Exit
BIOS BIOS BIOS
.
33
34
MS-7677
tWTR
. I/O gating
.
tRRD
active-to-active .
tRTP
.
tFAW
tFAW (four activate window delay) .
tWCL
tWCL (Write CAS Latency) .
tCKE
tCKE .
tRTL
tRTL .
Advanced Channel 1/ 2 Timing Configuration
<Enter> .
.
GT OverClocking
.
GT Ratio
.
Adjusted GT Frequency
. ( ).
Spread Spectrum
()
. EMI
.
* EMI [Disabled]
. EMI EMI
.
* EMI .
EMI .
*
.
35
CPU Features
<Enter> . CPU
.
Save & Exit
36
MS-7677
Franais
Pour commencer
Flicitations, vous venez daqurir une carte mre Mini-ITX des sries H61I-E35
(B3) (MS-7677 v1.x). Les sries sont bases sur les puces Intel H61 (B3) offrant un systme trs performant. La carte fonctionne avec les processeurs Intel
LGA1155 avancs, les sries sont trs performanantes et offrent une solution
adapte tant aux professionnels quaux particuliers.
Schma
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
37
SPCIFICATIONS
Processeurs
Intel Sandy Bridge processeurs dans le paquet LGA1155
(Pour plus dinformation sur le CPU, veuillez visiter
http://www.msi.com/service/cpu-support)
Jeu de puces
Puces Intel H61 (B3)
Mmoire supporte
2 DDR3 DIMMs supportent DDR3 1333/ 1066 SDRAM (total Max. 16GB)
Supporte le mode double-canaux
(Pour plus dinformation sur les composants compatibles, veuillez visiter
http://www.msi.com/service/test-report)
LAN
Supporte LAN 10/ 100/ 1000 par Realtek 8111E
Audio
Puce intgre par Realtek ALC887
Supporte 8 canaux audio out
Conforme aux spcifications Azalia 1.0
SATA
4 ports SATA 3Gb/s par Intel H61 (B3)
Connecteurs
Panneau arrire
1 port souris PS/2
1 port clavier PS/2
1 port VGA*
1 port HDMI*
4 ports USB 2.0
1 prise LAN
3 prises audio flexibles
*(Les ports VGA et HDMI ne fonctionnent quavec Processeur Graphique
Intgr.)
Connecteurs intgrs
2 connecteurs USB 2.0
1 connecteur audio avant
1 connecteur TPM
1 connecteur S/PDIF-Out
Emplacements
1 emplacement PCIE x1
Dimension
Mini-ITX (17.0 cm X 17.0 cm)
Montage
4 trous de montage
Si vous dsirez acheter des accessoires et vous avez besoin de numro des
pices, vous pouvez chercher sur la page website et trouver les dtails sur notre
adresse ci-dessous http://www.msi.com/index.php
38
MS-7677
Panneau arrire
Le panneau arrire dispose les connecteurs suivants :
LAN
Souris
Port VGA
Ligne-In
Ports USB
Ligne-Out
Clavier
Ports USB
Port HDMI
MIC
Nota : pour atteindre leffet de son 8-canaux, le 7me et 8me canaux doivent tre
sortis du panneau avant.
Installation du matriel
Ce chapitre vous indique comment installer le CPU, les modules de mmoire,
ainsi que les cavaliers sur la carte. Lors de linstallation du matriel, veuillez suivre
les instructions de montage pour viter dendommager quoi que ce soit.
Procdure dintallation du CPU et le ventilateur pour LGA1155
Quand vous installez votre CPU, assurez-vous que le CPU possde dun systme
de refroidissement pour prvenir le surchauffe. Si vous ne possdez pas de systme de refroidissement, contactez votre revendeur pour vous en procurer un et
installez-le avant dallumer lordinateur.
Introduction du LGA 1155 CPU
La surface du LGA 1155 CPU. Noubliez pas dappliquer un compos de transfert
thermique pour une meilleure dispersion de chaleur.
Important
Veuillez utiliser le ventilateur de CPU emball ou dautre ventilateurs avancs
pour maintenir la stabilit du systme.
Cl dalignement
Cl dalignement
39
2.
3.
La douille du CPU possde une couverture plastique qui protge la contact. Avant dinstaller le
CPU, toujours gardez-la pour protger les pins de
la douille. Retirez cette couverture.
4.
Aprs avoir confirm la direction du CPU pour joindre correctement, dposez le CPU dans larmature
du logement de douille. Faites attention au bord de
sa base. Notez quon aligne les coins assortis.
5.
6.
7.
8.
9.
Important
* Lisez le statut du CPU dans le BIOS.
* Quand le CPU nest pas install, toujours protgez vos pins de la douille CPU
avec le plastique de protection pour viter tout dommage.
* Les photos de la carte montres dans cette section ne sont que pour une dmonstration de linstallation du CPU et son ventilateur. Lapparence de votre
carte mre peut varier selon le modle que vous achetez.
* Veuillez vous-rfrer la documentation dans le paquet du ventilateur de CPU
pour plus de dtails sur linstallation du ventilateur de CPU.
40
MS-7677
Installation des Modules de Mmoire
. Le module de mmoire ne possde quune seule encoche au centre et quil
nest convenable que dans la correcte orientation.
2.
Insrez le module de mmoire verticalement dans le slot DIMM. Puis poussez-le l-dedans jusqu ce que le doigt dor sur le module de mmoire soit
profondment insr dans lemplacement DIMM. Vous ne opuvez presque
pas voir le doigt dor si le module de mmoire est correctement insr dans
le slot DIMM.
3.
Volt
Encoche
Important
* Au mode Dual-Channel, assurez-vous que vous installez les modules de mmoire du mme type et de la mme densit dans des slots DIMM de canaux
diffrents.
* Pour lancer avec succs votre ordinateur, insrez tout dabord les modules de
mmoire DIMM1.
41
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
Important
* Assurez-vous que tous les connecteurs sont relis lalimentation ATX pour
assurer une stabilit de la carte mre.
* Lalimentation de 350 watts (et suprieur) est fortement recommand pour la
stabilit du systme.
Important
Veuillez ne pas tordre le cble Srial ATA 90-degrs. Cela pourrait lendommager
et entraner la perte de donnes lors des phases de transfert de celles-ci.
42
MS-7677
Connecteurs dalimentation du ventilateur : CPUFAN, SYSFAN1
Les connecteurs dalimentation du systme de refroidissement suportent un systme de refroidissement de +12V. Lors de la connexion du cble, assurez-vous
que le fil soit positif et connect au +12V; le cble noir connect au GND. Si la
carte mre possde un chipset System Hardware Monitor intgr, vous devez
utiliser un ventilateur ayant ces caractristiques si bous voulez contrler le ventilateur du CPU.
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
43
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
n
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
d
C un +
.N o 1
0 r B 11 .G
8 US B
. S
6 .U C
4 VC
.
2
in
P d
n
o u +
.N r o 0
9 .G SB 07 .U B
S
5 .U CC
3 .V
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
44
MS-7677
Cavalier deffacement CMOS : JBAT1
Le CMOS RAM intgr reoit une alimentation dune batterie externe qui permet de garder les donnes de configuration du systme. Avec le CMOS RAM,
le systme peut automatiquement amorcer OS chaque fois quil soit allum. Si
vous voulez effacer la configuration du systme, rglez le cavalier pour effacer
les donnes.
JBAT1
1
Important
Vous pouvez effacer le CMOS en positionnant les 1-2 pin orsque le PC est dsactiv, puis ouvrez-le. Evitez surtout deffacer le CMOS lorsque le PC est allum,
cela endommagera la carte mre.
45
Rglage bios
Lorsque le PC est dmarr, le processeur de POST (Power On Self Test) se met
en route. Quand le message ci-dessous appat lcran, appuyez sur <DEL> pour
accder au Setup (Rglages).
Press DEL to enter Setup Menu
(Appuyez sur DEL pour accder au SETUP)
Si le message disparat avant que vous nayez appuy sur la touche, redmarrez
le PC avec laide du bouton RESET. Vous pouvez aussi le redmarrer en utilisant
smultanment la combinaison des touches <Ctrl>, <Alt>, et <Delete>.
La barre menu
Main Menu
Utilisez ce menu pour paramtrer des lments standards du systme tel que
lheure, la date etc.
Advanced
Utilisez ce menu pour rgler les articles des fonctions avances spcifiques.
Overclocking
Utilisez ce menu pour spcifier vos rglages du DRAM timing et des fonctions
du CPU.
M-Flash
Utilisez ce menu pour lire/ flash le BIOS du (au) lecteur de stockage (FAT/ FAT32
forme uniquement).
Security
Utilisez ce menu pour rgler les mots de passe de superviseur et dutilisateur.
46
MS-7677
Boot
Utilisez ce menu pour spcifier la priorit des priphriques de dmarrage.
Save & Exit
Ce menu vous permet de charger les rglages par dfaut de la manufacture dans
le BIOS et de quitter lutilitaire de rglages BIOS avec ou sans les changements.
Overclocking
47
48
MS-7677
tRFC
Ce rglage dtermine le temps que RFC prend pour lire ou crire une cellule
de mmoire.
tWR
Lintervalle de temps minimum entre la fin dapparition dcriture de donnes et
le dbut de lordre de prcharge. Permet aux amplificateurs sensitifs de restaurer les donnes aux cellules.
tWTR
Lintervalle de temps minimum entre la fin dapparition dcriture de donnes et
le dbut de lordre de pr-charge. Permet au pont I/O de faire sur-fonctionner
lamplificateur sensitif avant quun ordre de lecture commences.
tRRD
Spcifie le retard active--active des diffrentes banques.
tRTP
Lintervalle de temps entre un ordre de lire et un ordre de pr-charge.
tFAW
Cet article sert rgler le timing tFAW (dlai de quatre fentres actives).
tWCL
Cet article sert rgler le timing tWCL (Write CAS Latency).
tCKE
Cet article sert rgler le timing tCKE.
tRTL
Cet article sert rgler le timing tRTL.
Advanced Channel 1/ 2 Timing Configuration
Appuyez <Enter> pour entrer dans le sous-menu. Vous pouvez rgler le timing
de mmoire avance pour chaque canal.
GT OverClocking
Ce menu vous permet dactiver/ dsactiver loverclocking des graphiques intgrs.
GT Ratio
Ce rglage contrle le ratio de la frquence graphique intgre pour activer les
graphiques intgres de fonctionner en diffrentes combinaisons de frquence.
Adjusted GT Frequency
Il montre la frquence ajuste de graphique intgre. Lecture uniquement.
Spread Spectrum
Lorsque le gnrateur dhorloge de la carte mre fonctionne, les valeurs extrmes
(spikes) crent des interfrences lectromagntiques EMI (Electromagnetic Interference). La fonction Spread Spectrum rduit ces interfrences en rglant les impultions pour que les spikes des impultions sont rduits au courbes plus plates.
49
Important
* Si vous navez pas de problme dEMI, laissez loption sur [Disable], ceci vous
permet davoir une stabilit du systme et des performances optimales. Dans le
cas contraire, choisissez Spread Spectrum pour rduire les EMI.
* Plus la valeur Spread Spectrum est importante, plus les EMI sont rduites, et le
systme devient moins stable. Pour la valeur Spread Spectrum la plus convenable, veuillez consulter le rglement EMI local.
* Noubliez pas de dsactiver la fonction Spread Spectrum si vous tes en train
doverclocker parce que mme un battement lger peut causer un accroissement temporaire de la vitesse de lhorloge qui verrouillera votre processeur
overclock.
CPU Features
Appuyez sur <Enter> pour entrer dans le sous-menu. Dans le sous-menu, vous
pouvez ajuster les fonctions du CPU.
Save & Exit
50
MS-7677
DEUTSCH
eINLEITUNG
Danke, dass Sie die H61I-E35 (B3) Serie (MS-7677 v1.x) Mini-ITX Mainboard
gewhlt haben. Diese Serie basiert auf dem Intel H61 (B3) Chipsatz und
ermglicht so ein optimales und effizientes System. Entworfen, um den hochentwickelten Intel LGA1155 Prozessor zu untersttzen, stellt die Serie die ideale
Lsung zum Aufbau eines professionellen Hochleistungsdesktopsystems dar.
Layout
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
51
SPEZIFIKATIONEN
Prozessoren
Intel Sandy Bridge Prozessor fr LGA1155
(Weitere CPU Informationen finden Sie unter
http://www.msi.com/service/cpu-support)
Chipsatz
Intel H61 (B3) Chipsatz
Speicher
2 DDR3 DIMMs untersttzen DDR3 1333/ 1066 SDRAM (gesamt max. 16GB)
Untersttzt die Modus Dual-Kanal
(Weitere Informationen zu kompatiblen Speichermodulen finden Sie unter
http://www.msi.com/service/test-report)
LAN
Untersttzt LAN 10/ 100/ 1000 ber Realtek 8111E
Audio
Onboard Soundchip Realtek ALC887
8-Kanal Audio-Ausgang
Erfllt die Azalia Spezifikationen
SATA
4 SATA 3Gb/s Anschlsse ber Intel H61 (B3)
Anschlsse
Hintere Ein-/ und Ausgnge
1 PS/2 Mausanschluss
1 PS/2 Tastaturanschluss
1 VGA Anschluss*
1 HDMI Anschluss*
4 USB 2.0 Anschlsse
1 LAN Anschluss
3 Audiobuchsen
*(Der VGA- and HDMI-Anschluss arbeitet nur mit integriertem
Grafikprozessor.)
On-Board Stiftleiste/ Anschlsse
2 USB 2.0 Stiftleisten
1 Audio Stiftleiste fr Gehuse Audio Ein-/ Ausgnge
1 TPM Stiftleiste
1 S/PDIF-Ausgang Stiftleiste
Steckpltze
1 PCIE x1-Steckplatz
Form Faktor
Mini-ITX (17,0 cm X 17,0 cm)
Montage
4 Montagebohrungen
Wenn Sie fr Bestellungen von Zubehr Teilenummern bentigen, finden Sie
diese auf unserer Produktseite unter http://www.msi.com/index.php
52
MS-7677
Hinteres Anschlusspanel
Das hintere Anschlusspanel verfgt ber folgende Anschlsse:
LAN
Maus
VGA Anschluss
Line-In
USB Anschlsse
Line-Out
Tastatur
HARDWARE SETUP
Dieses Kapitel informiert Sie darber, wie Sie die CPU und Speichermodule einbauen, des weiteren darber, wie die Steckbrcken auf dem Mainboard gesetzt
werden. Handhaben Sie die Komponenten whrend des Einbaus vorsichtig und
halten Sie sich an die vorgegebene Vorgehensweise beim Einbau.
CPU & Khler Einbau fr Sockel LGA1155
Wenn Sie die CPU einbauen, stellen Sie bitte sicher, dass Sie auf der CPU einen
Khler anbringen, um berhitzung zu vermeiden. Verfgen Sie ber keinen Khler, setzen Sie sich bitte mit Ihrem Hndler in Verbindung, um einen solchen zu
erwerben und zu installieren.
Erklrung zur LGA 1155 CPU
Die Obserseite der LGA 1155 CPU. Vergessen Sie nicht, etwas Siliziumwrmeleitpaste auf die CPU auf zut ragen,um eine Ableitung der Hitze zu erzielen.
Wichtig
Bitte verwenden Sie den eingepackten CPU-Lfter oder andere verbesserte Khler, um die Systemstabilitt beizubehalten.
Justierung
Justierung
Folgen Sie den Schritten unten, um die CPU und den Khler ordnungsgem zu installieren. Ein fehlerhafter Einbau
fhrt zu Schden an der CPU und dem Mainboard.
.
2.
Klappen Sie den Hebel ganz auf und ffnen Sie die
Metallverschluss-klappe.
3.
Der CPU-Sockel besitzt zum Schutz eine Plastikabdeckung. Lassen Sie vor der Installation diese Schutzkappe auf dem Sockel um Schden zu vermeiden.
Entfernen Sie die Kappe.
4.
Vergewissern Sie sich anhand der Justiermarkierungen und dem gelben Dreieck, da die CPU in der korrekten Position ist. Setzen Sie anschlieend die CPU
in den Sockel.
5.
6.
Schlieen Sie die Abdeckung des Sockels und drcken Sie den Verschlusshebel mit leichtem Druck nach
unten.
7.
8.
Kontrollieren Sie die vier Haken sind in richtiger Position, bevor Sie die Khlvorrichtung anbringen.
9.
Drcken Sie den Verschlusshebel mit leichtem Druck nach unten und arretieren Sie den Hebel unter dem Rckhaltehaken des CPU-Sockels.
Wichtig
* Prfen Sie die Status der CPU im BIOS.
* Wenn keine CPU installiert ist, schtzen Sie immer den CPU-Sockel durch die
Plastikabdeckung.
* Die Mainboard Fotos, die in diesem Abschnitt gezeigt werden, sind fr Demonstration der CPU/ Khler Installation. Das Aussehen Ihres Mainboard kann
abhngig von dem Modell schwanken, das Sie kaufen.
* Beziehen Sie bitte sich die auf Unterlagen im CPU Khlerpaket fr mehr Details
ber die CPU Khlerinstallation.
54
MS-7677
Vorgehensweise beim Einbau von Speicher Modulen
. Die Speichermodule haben nur eine Kerbe in der Mitte des Moduls. Sie passen nur in einer Richtung in den Sockel.
2.
3.
Prfen Sie von Hand, ob das Arbeitsspeichermodul von den seitlichen Bgeln
am DIMM-Steckplatz richtig gehalten wird.
Volt
Kerbe
WICHtIG
* Stellen Sie im Zweikanalbetrieb bitte sicher, dass Sie Module des gleichen Typs
und identischer Speicherdichte in den DIMM Slots unterschiedlicher Kanle
verwenden.
* Um einen sicheren Systemstart zu gewhrleisten, bestcken Sie immer DIMM
1 zuerst.
55
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
V
2
1 V
.+ 2
3 .+1
4
wichtig
* Stellen Sie die Verbindung aller drei Anschlsse mit einem angemessenem ATX
Netzteil sicher, um den stabilen Betrieb des Mainboards sicher zu stellen.
* Netzteile mit 350 Watt (und mehr) werden aus Grnden der Systemstabilitt
dringend empfohlen.
WICHtIG
Bitte falten Sie das Serial ATA Kabel nicht in einem Winkel von 90 Grad. da dies
zu Datenverlusten whrend der Datenbertragung fhrt.
56
MS-7677
Stromanschlsse fr Lfter: CPUFAN, SYSFAN1
Die Netzteillfter Anschlsse untersttzen aktive Systemlfter mit +12V. Wenn
Sie den Stecker mit dem Anschluss verbinden, sollten Sie immer darauf achten,
dass der rote Draht der positive Pol ist und mit +12V verbunden werden sollte,
der schwarze Draht ist der Erdkontakt und sollte mit GND verbunden werden.
Besitzt Ihr Mainboard einen Chipsatz zur berwachung der Systemhardware und
Steuerung der Lfter, dann brauchen Sie einen speziellen Lfter mit Tacho, um
diese Funktion zu nutzen.
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
S/PDIF-Ausgang: JSP1
Die S/PDIF (Sony & Philips Digital Interconnect Format) Schnittstelle wird fr die
bertragung digitaler Audiodaten verwendet.
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
57
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
n
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
58
MS-7677
Steckbrcke zur CMOS-Lschung: JBAT1
Der Onboard CMOS Speicher (RAM) wird ber eine zustzliche Betterie mit Strom
versorgt, um die Daten der Systemkonfiguration zu speichern. Er ermglicht es
dem Betriebssystem, mit jedem Einschalten automatisch hochzufahren. Wenn Sie
die Systemkonfiguration lschen wollen, mssen Sie die Steckbrcke fr kurze
Zeit umsetzen (Lschen Daten).
JBAT1
1
Halten Daten
Lschen Daten
WICHtIG
Sie knnen den CMOS lschen, indem Sie die Pins1-2 verbinden, whrend das
System ausgeschaltet ist und danach wieder ffnen. Versuchen Sie niemals die
Daten im CMOS zu lschen, wenn das System eingeschaltet ist. Die Hauptplatine
kann dadurch beschdigen.
PCIE-Steckplatz
Der PCIE-Steckplatz untersttzt eine Erweiterungskarte mit der PCIE-Schnittstelle.
59
BIOS Setup
Nach dem Einschalten beginnt der Computer den POST (Power On Self Test
Selbstberprfung nach Anschalten). Sobald die Meldung unten erscheint
drcken Sie die Taste <DEL> , um das Setup aufzurufen.
Press DEL to enter Setup Menu
(ENTF drcken, um das Setup-Men zu ffnen)
Wenn die Nachricht verschwindet, bevor Sie reagieren und Sie mchten immer
noch ins Setup, starten Sie das System neu, indem Sie es erst AUS- und danach wieder ANSCHALTEN, oder die RESET-Taste am Gehuse bettigen.
Sie knnen das System auerdem neu starten, indem Sie gleichzeitig die Tasten
<Strg>,<Alt> und <Entf> drcken (bei manchen Tastaturen <Ctrl>,<Alt> und
<Del>).
Die Menleise
Main Menu
In diesem Men knnen Sie die Basiskonfiguration Ihres Systems anpassen, so
z.B. Uhrzeit, Datum usw.
Advanced
Verwenden Sie diesen Menpunkt, um eigene weitergehende Einstellungen an
Ihrem System vorzunehmen.
Overclocking
Hier knnen Sie Einstellungen zu DRAM-Timing und CPU Funktionen vornehmen.
M-Flash
In diesem Men knnen Sie das BIOS vom Speicher-Antrieb abtasten/ aufblinken
(nur FAT/ FAT32 Format).
60
MS-7677
Security
Mit diesem Men knnen Sie Supervisor- und Benutzerkennwrter setzen.
Boot
Verwenden Sie dieses Men, um die Prioritt der Boot-Gert vorzunehmen.
Save & Exit
Hier knnen Sie die BIOS-Werkseinstellungen oder Standardeinstellungen laden.
Vernderungen speichern oder lschen und verlassen Sie das BIOS-Setup.
Overclocking
61
62
MS-7677
Speicherzelle.
tRFC
Diese Einstellung definiert die Zeit (RFC) zum Lesen und Schreiben einer
Speicherzelle.
tWR
Minimum Intervall zwischen dem Datenflussende und dem Beginn eines vorgeladenen Befehls. Erlaubt die Wiederherstellung der Daten in die Zellen.
tWTR
Minimum Intervall zwischen dem Datenflussende und dem Beginn eines
Spaltenlesebefehls. Es gestattet den I/O Ansteuerungssignalen die Datenwiederherstellung der Zelle vor dem Lesebefehl zu berschreiben.
tRRD
Legt die Aktiv-zu-Aktiv Verzgerung fr unterschiedliche Bnke fest.
tRTP
Legt das Zeitintervall zwischen dem Lesebefehl und dem vorgeladenen Befehl
fest.
tFAW
Einstellen des tFAW -Zeitintervalls (four activate window delay).
tWCL
Einstellen des tWCL- Zeitintervalls (Write CAS Latency).
tCKE
Einstellen des tCKE- Zeitintervalls.
tRTL
Einstellen des tRTL- Zeitintervalls.
Advanced Channel 1/ 2 Timing Configuration
Drcken Sie die Eingabetaste <Enter>, um das Untermen aufzurufen. Hier
knnen fr jeden Kanal erweiterte Speichereinstellungen vorgenommen
werden.
GT OverClocking
Hier knnen Sie die bertaktung der integrierten Grafik aktivieren/ deaktivieren.
GT Ratio
Diese Einstellung steuert das Verhltnis der integrierten Grafikfrequenz, um die
integrierten Grafik mit eine anderen Frequenzkombinationen zu arbeiten.
Adjusted GT Frequency
Zeigt die angepasste Frequenz integrierter Grafik. Nur Anzeige keine nderung
mglich.
Spread Spectrum
Pulsiert der Taktgenerator des Motherboards, erzeugen die Extremwerte (Spitzen) der Pulse EMI (Elektromagnetische Interferenzen). Die Spread Spectrum
Funktion reduziert die erzeugten EMI, indem die Pulse so moduliert werden, das
die Pulsspitzen zu flacheren Kurven reduziert werden.
63
WICHtIG
* Sollten Sie keine Probleme mit Interferenzen haben, belassen Sie es bei der
Einstellung [Disabled] (ausgeschaltet), um bestmgliche Systemstabilitt und
-leistung zu gewhrleisten. Stellt fr sie EMI ein Problem dar, whlen Sie die
gewnschte Bandbreite zur Reduktion der EMI.
* Je grer Spread Spectrum Wert ist, desto grer nimmt der EMI ab, und das
System wird weniger stabil. Bitte befragen Sie Ihren lokalen EMI Regelung zum
meist passend Spread Spectrum Wert.
* Denken Sie daran Spread Spectrum zu deaktivieren, wenn Sie bertakten, da
sogar eine leichte Schwankung eine vorbergehende Taktsteigerung erzeugen
kann, die gerade ausreichen mag, um Ihren bertakteten Prozessor zum einfrieren zu bringen.
CPU Features
Drcken Sie die Eingabetaste <Enter>, um das Untermen aufzurufen. In den
Unterpunkten knnen Sie die CPU-Funktionen anpassen.
Save & Exit
64
MS-7677
H61I-E35 (B3) (MS7677 v1.x) Mini-ITX.
Intel H61 (B3).
Intel LGA1155
.
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
65
http://www.msi.com/service/test-report)
LAN
LAN 10/ 100/ 1000 Realtek 8111E
Realtek ALC887
8
Azalia 1.0
SATA
4 SATA 3/ Intel H61 (B3)
1 PS/2
1 PS/2
1 * VGA
1 * HDMI
4 USB 2.0
1 LAN
3
*( VGA HDMI Integrated Graphics Processor.)
,
2 USB 2.0
1
1 TPM
1 S/PDIF-Out
1 PCIE x1
Mini-ITX (17.0 X 17.0 )
4
http://www.msi.com/index.php
66
MS-7677
LAN
VGA
USB
USB
HDMI
: 8- , 7- 8-
.
,
.
, .
LGA1155
.
.
LGA 1155
LGA 1155 .
.
,
.
1 .
67
.
.
.
2.
3.
,
. ,
.
.
4.
, .
,
5.
,
.
6.
7.
8.
,
.
9.
.
, .
0. .
. ,
.
2. ,
.
* BIOS.
* ,
.
* , ,
.
, .
*
.
68
MS-7677
. .
.
2.
DIMM .
, DIMM
. DIMM ,
.
DIMM ,
.
3.
, DIMM
.
* ,
.
* , DIMM1.
69
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
4- ATX: JPWR2
4-.
.
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
* , ATX .
* 350 ( )
.
Serial ATA.
.
70
MS-7677
: CPUFAN, SYSFAN1
+12. ,
+12, - GND.
,
.
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
S/PDIF-Out: JSP1
S/PDIF (Sony &
Philips Digital Interconnect Format) .
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
: JFP1
. JFP1 Intel Front Panel I/O Connectivity
Design Guide.
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
71
: JAUD1
.
Intel Front Panel I/O Connectivity Design Guide.
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
n
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
d
C un +
.N o 1
0 r B 11 .G
8 US B
. S
6 .U C
4 VC
.
2
in
P d
n
o u +
.N r o 0
9 .G SB 07 .U B
S
5 .U CC
3 .V
TPM : JTPM1
TPM (Trusted Platform Module)
.
TPM.
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
72
MS-7677
CMOS: JBAT1
CMOS ,
. , CMOS ,
.
( CMOS), .
JBAT1
1
CMOS 1-2
. . CMOS
: .
PCI Express
PCIE
PCIE.
PCI Express x1 .
73
BIOS
. POST
( ).
, <DEL> .
Press DEL to enter Setup Menu
( DEL SETUP)
, .
RESET <Ctrl>,
<Alt> <Delete>.
Main Menu ( )
, , . .
Advanced ()
.
Overclocking ()
DRAM .
M-Flash
/ BIOS (
FAT/ FAT32).
Security ()
.
Boot ()
.
74
MS-7677
Save & Exit ( )
BIOS
BIOS BIOS
.
Overclocking ()
75
76
MS-7677
tWR
.
.
tWTR
. /
.
tRRD
--
.
tRTP
.
tFAW
tFAW (four activate window delay).
tWCL
tWCL (Write CAS Latency).
tCKE
tCKE.
tRTL
tRTL.
Advanced Channel 1/ 2 Timing Configuration
<Enter> .
.
GT OverClocking
/ .
GT Ratio
,
.
Adjusted GT Frequency
. .
Spread Spectrum
,
- EMI (Electromagnetic Interference).
Spread Spectrum ,
.
* , [Disabled]
() . ,
, Spread Spec-
77
trum .
* Spread Spectrum,
, .
Spread Spectrum,
, .
* Spread Spectrum,
. ,
.
CPU Features
<Enter> .
CPU.
Save & Exit
78
MS-7677
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
79
Realtek ALC887
8
Azalia 1.0
SATA
Intel H61 (B3) 4 SATA 3Gb/s
1 PS/2
1 PS/2
1 VGA *
1 HDMI *
4 USB 2.0
1 LAN
3
*( VGA HDMI )
2 USB 2.0
1
1 TPM
1 S/PDIF-Out
1 PCIE x1
: http://www.msi.com/index.php
80
MS-7677
:
LAN
VGA
Line-In
USB
Line-Out
USB
HDMI
MIC
: 8 7 8
CPU
LGA1155 CPU
CPUCPU
CPU
LGA 1155 CPU
LGA 1155 CPU CPU
CPU
Pin1
81
CPU
CPU
.
2.
3.
CPUCPU
CPU
4.
CPUCPU
CPU
CPU
5.
CPU ,
CPU
6.
7.
8.
9.
0.
.
2. CPUCPU
* BIOSCPU
* CPUCPU
* CPU/
* CPU CPU
82
MS-7677
.
2.
DIMM
3.
* DIMM1
83
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
* ATX
* 350 ()
ATA : SATA1 ~ 4
ATAATA
ATA90
84
MS-7677
: CPUFAN, SYSFAN1
+12V
,+12VGND
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
S/PDIF-Out : JSP1
S/PDIF (Sony & Philips )
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
: JFP1
JFP1Intel
I/O
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
85
: JAUD1
Intel I/O
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
d
C un +
.N o 1
0 r B 11 .G
8 US B
. S
6 .U C
4 VC
.
2
in
P d
n
o u +
.N r o 0
9 .G SB 07 .U B
S
5 .U CC
3 .V
1
TPM : JTPM1
TPM (Trusted Platform Module)TPM
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
86
MS-7677
CMOS : JBAT1
CMOS RAM
CMOS RAM
JBAT1
1
1-2CMOS
CMOS
PCI Express
PCI Express PCI Express
PCI Express x1
87
Setup
POST()
<DEL>
Press DEL to enter Setup Menu
Setup
RESET<Ctrl><Alt><Delete>
Main Menu
Advanced
BIOS
Overclocking
DRAMCPU
M-Flash
BIOS FAT/FAT32
Security
Boot
88
MS-7677
Save & Exit
BIOS
89
tRCD
DRAM(RAS)
(CAS)DRAM
tRP
(RAS) DRAM
DRAM
tRAS
RAS
tRFC
RFC
tWR
90
MS-7677
tWTR
I/O
tRRD
active-to-active
tRTP
tFAW
tFAW (four activate window delay)
tWCL
tWCL (Write CAS Latency)
tCKE
tCKE
tRTL
tRTL
Advanced Channel 1/ 2 Timing Configuration
<Enter>
GT OverClocking
/
GT Ratio
Adjusted GT Frequency
Spread Spectrum
EMI
* EMI
[Disabled]EMISpread Spectrum()
EMI
* Spread Spectrum () EMI
Spread Spectrum () EMI
* , Spread Spectrum ()
CPU Features
<Enter> CPU
91
&
Save Options
Discard Changes
Restore Defaults
BIOS
== ==
92
MS-7677
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
93
Realtek ALC887
8
Azalia 1.0
SATA
Intel H61 (B3) 4 SATA 3Gb/s
1 PS/2
1 PS/2
1 VGA *
1 HDMI *
4 USB 2.0
1
3
*( VGA HDMI )
2 USB 2.0
1
1 TPM
1 S/PDIF-Out
1 PCIE x1
4
http://tw.msi.com
94
MS-7677
VGA
USB
USB
HDMI
8- 7 8
LGA1155 CPU
CPU
LGA775 CPU
CPU CPU
CPU,
Pin1
95
.
2.
3.
CPU CPU
CPU
4.
CPU
5.
CPU
CPU
6.
7.
8.
9.
0.
.
* BIOS CPU
* CPU CPU
*
* CPU CPU
96
MS-7677
.
2.
3.
* DIMM1
97
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
* ATX
* 350
Serial ATA 90
98
MS-7677
CPUFAN, SYSFAN1
+12V
+12V GND
CPU
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
S/PDIF-Out JSP1
S/PDIF (Sony & Philip Digital Interconnect Format)
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
JFP1
LED JFP1 Intel /
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
99
JAUD1
Intel /
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
d
C un +
.N o 1
0 r B 11 .G
8 US B
. S
6 .U C
4 VC
.
2
in
P d
n
o u +
.N r o 0
9 .G SB 07 .U B
S
5 .U CC
3 .V
1
TPM JTPM1
TPM
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
100
MS-7677
CMOS JBAT1
CMOS RAMCMOS RAM
JBAT1
1
PCI Express
PCI Express PCIE
PCI Express x1
101
BIOS
POST ()
<DEL>
Press DEL to enter Setup Menu
( DEL )
Main Menu
Advanced
Overclocking
CPU
Mflash
(FAT FAT32 ) flash BIOS
Security
Boot
102
MS-7677
Save & Exit
BIOS BIOS BIOS
Overclocking
103
tRAS
RAS
tRFC
RFC
tWR
(sense amplifier)
tWTR
tRRD
(active-to-active)
tRTP
tFAW
tFAW (four activate window delay)
tWCL
tWCL (Write CAS Latency)
tCKE
tCKE
tRTL
tRTL
104
MS-7677
Advanced Channel 1/ 2 Timing Configuration
<Enter>
GT OverClocking
GT Ratio
Adjusted GT Frequency
Spread Spectrum
(EMI) EMI
* (EMI) [Disabled]
EMI
*
CPU Features
<Enter> CPU
105
Save Changes
Discard Changes
Restore Defaults
BIOS
== Boot Override ==
106
MS-7677
CPUFAN
DIMM1
DIMM2
JPWR2
Top : mouse
Bottom: keyboard
USB2.0 ports
JPWR1
JAUD1
T:Line-In
M:Line- Out
B:Mic-In
JFP1
JSP1
JBAT1
SYSFAN1
PCI _E1
JTPM1
SATA4
SATA3
SATA2
SATA1
107
Realtek ALC887
8
Azalia 1.0
SATA
Intel H61 (B3)SATA 3Gb/s4
I/O
PS/2 1
PS/2 1
VGA 1*
HDMI 1*
USB 2.0 4
LAN 1
3
*(VGAHDMI
)
USB 2.0 2
1
TPM 1
S/PDIF 1
PCIE x1 1
4
Web
http://www.msi.com/index.php
108
MS-7677
I/O
LAN
VGA
Line-In
USB
Line-Out
USB
HDMI
MIC
: 878
LGA1155 CPU
CPU
CPU
CPU
109
CPUCPU
CPU
.
CPU()
2.
3.
4.
CPUalignment key()CPU
[]
5.
CPU
6.
7.
8.
9.
CPU
0.
.
2. CPU
* CPUBIOS
* CPU
*
* CPUCPU
110
MS-7677
.
2.
DIMMDIMMDIMM
3.
* DIMM1
111
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. +5 s un d
2 1. Re o un d
2 0. Gr o n #
2 9. Gr rou ON d
1 8. G - un
1 7. PS o
1 . r V V
6
G
1 5. -12 .3
1 4. +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 1.+ +1 B OK
1 0. VS R nd
1 .5 W u
9 .P ro nd
8 .G 5V u
7 .+ ro nd
6 .G 5V u
5 .+ ro V
4 .G 3.3 3V
3 .+ 3.
2 .+
1
ATX 4: JPWR2
4CPU
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
* 350W
ATA: SATA1 ~ 4
ATA
ATA
ATA90
112
MS-7677
: CPUFAN, SYSFAN1
+12V+12V
GND
CPUFAN
SYSFAN1
d
n
u
ro 2V se
.G 1
1 .+ o U
2 .N
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en ntr
2 .S o
3 .C
S/PDIF: JSP1
5.1/7.1
d
n
u F
r o DI
.G P
1 .S CC
2 .V
3
: JFP1
LED
JFP1
P
o
w
e
r
0
.N
r
L
E
D
in
P o 8. +
.
6 .4 +
.
2
ch
it
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 +
H
.
7 .5 .3 .+
1
JFP1
113
: JAUD1
io
ct
te
e
D
e
n
o
n
h
io
P
ct #
d
e E
a
e Pin et C
D EN
.H
0 o
1 N IC S
.
8 .M RE nd
6 .P ou
4 Gr
.
2
L
e D
n
o N
h E R
P _S ne
d
o
a E h
e NS P
.H E d
9 .S a R
7 .He IC L
5 .M I C
3 .M
1
d
C un +
.N o 1
0 r B 11 .G
8 US B
. S
6 .U C
4 VC
.
2
in
P d
n
o u +
.N r o 0
9 .G SB 07 .U B
S
5 .U CC
3 .V
1
TPM: JTPM1
TPM (Trusted Platform Module)
TPM
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 .LP C R loc
7 .LP C C
5 .L P C
3 .LP
1
d
n
u nd
r
ro u n r
e
.G ro Pi we Q r ow
4
1 2 . G o P o IR w e y p
1 0.N V ial o b
1 .5 er P nd
8 S 3V ta
.
6 3. S
.
4 .3V
2
114
MS-7677
CMOS: JBAT1
BIOSCMOS
CMOSOS
JBAT1
1
CMOS1-2()
CMOS
PCI Express
PCI ExpressPCI Express
PCI Express x1
115
BIOS
POST (Power On Self Test)
<DEL>
Main Menu
/
Advanced
BIOS
Overclocking
DRAMCPU
M-Flash
USBBIOS(FAT/FAT32
)
Security
116
MS-7677
Boot
117
CPU
Command Rate
DRAM
tCL
SDRAM
CAS
tRCD
RAS()CAS()
DRAM
tRP
DRAM
RAS
DRAMDRAM
DRAM
tRAS
RAS()
tRFC
RFC
tWR
tWR
118
MS-7677
tWTR
I/O gating
tRRD
tRTP
tFAW
tFAW
tWCL
tWCL
tCKE
tCKE
tRTL
tRTL
Advanced Channel 1/ 2 Timing Configuration
<Enter>
GT OverClocking
/
GT Ratio
Adjusted GT Frequency
Spread Spectrum
(EMI)
*
[Disabled]
[Enabled]
* Spread
Spectrum
119
* [Disabled]
CPU Features
<Enter>CPU
Save Options
Discard Changes
Restore Defaults
== Boot Override ==
120
<>
(Pb)
(Hg)
(Cd)
(Cr6+)
(PBB)
(PBDE)
(Battery)
/
(Cable/ Connector)
/ (Chassis/ Other)
(CD, DVD)
(Optical Disk Driver)
(PCAs)*
(I/O Device)
(Mouse, Keyboard)
(LCD Panel)
(Memory)
(CDDVD)
(Power Supply)
(Remote Control)
(Speakers)
(TV Tunner)
(Web Camera)
(Wireless Cards)
. *(PCB)IC
2.
3. :SJ/T11363-2006
4. :SJ/T11363-2006
EU RoHS
5. <>
EPUP (Environmental Protection Use Period)
6. EPUP-(SJ/Z
11388-2009)EPUP,