Académique Documents
Professionnel Documents
Culture Documents
Pgina 1 de 22
Cerrar SIS
Pantalla anterior
Producto: BACKHOE LOADER Modelo: 442D BACKHOE LOADER BRG Configuracin: 442D Backhoe Loader BRG00001-00827 (MACHINE) POWERED BY 3054 Engine
Pruebas y Ajustes
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System
Nmero de medio -RENR3584-05 Fecha de publicacin -01/10/2004 Fecha de actualizacin -26/10/2004
i02663114
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
S/N - BPN1-UP S/N - BRG1-UP S/N - BRY1-UP S/N - CXP1-UP S/N - FDP1-UP
Sudden movement of the machine or release of oil under pressure can cause serious injury to persons on or near the machine. To prevent possible injury, perform the procedure that follows before testing and adjusting the hydraulic system.
Personal injury or death can result from escaping fluid under pressure. Escaping fluid under pressure, even a very small pin-hole size leak, can penetrate body tissue and cause serious injury and possible death. If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury. Always use a board or cardboard when checking for a leak.
Table 1 Required Tools Part Number 6V-4143 177-7860 8T-0856 8T-0860 8C-3417 4C-9910 6V-8946 6V-9831 123-3893 Description Couplers Hose Assemblies Pressure Gauges Pressure Gauge Elbows Flow Meter Reducer Assemblies Cap Assembly Cap Assembly Quantity 4 2 2 2 2 1 2 1 1
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
6V-3989 8T-0857
4 1
Illustration 1 (1) Hydraulic pump (2) Flow compensator valve (3) Pressure compensator valve (4) Signal pressure tap
g00744000
Signal pressure tap (4) is located on hydraulic pump (1) . Flow compensator valve (2) and pressure compensator valve (3) are also located on hydraulic pump (1) . Access is gained from the bottom of the machine or access is gained by removing the floorplate.
g00778422
The system pressure tap (5) is located on the block for the pump discharge pressure. Access is gained from the bottom of the machine. Pump discharge pressures are known values. The pump discharge pressures can be tested during two
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
specific conditions. low pressure standby high pressure stall Prior to making any pump adjustments, perform "Low Pressure Standby Test", "Margin Pressure Test" and "High Pressure Stall Test". Increase the hydraulic oil temperature to the operating temperature by installing the boom lock and stalling the boom down for 60 seconds. Check for leaks.
Illustration 3
g00869466
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
Illustration 4
g00869467
b. Remove two bolts (8) and plate (9) . Remove floor mat (10) .
Illustration 5
g00869469
c. Remove four bolts (11) and set the floorplate (12) aside. 7. Install the 8T-0856 Pressure Gauges with a range of 0 to 6000 kPa (0 to 870 psi) to each hose assembly. Install one hose assembly to the pressure tap (5) for system pressure. Install one hose assembly to the signal pressure tap (4) . Note: Do not move any hydraulic hand controls or the steering wheel while the 8T-0856 Pressure Gauges are installed. The higher pressure that is created by upstroking the pump will damage the gauges. 8. Start the engine. Run the engine at HIGH idle. Check for leaks. 9. Do not move any hydraulic hand controls nor move the steering wheel. The pressure reading on the gauge that is attached to the pressure tap (5) for the system pressure should be 2850 750 kPa (415 110 psi). This pressure is the low pressure standby pressure. For best results, the low standby pressure should be set at approximately 3100 kPa (450 psi). 10. The pressure reading on the gauge that is attached to the signal pressure tap (4) should be
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
approximately 650 kPa (95 psi). This pressure is the steering signal pressure. The steering signal pressure is not adjustable. Note: The steering signal pressure will vary with each machine. The steering signal pressure of each machine should remain consistent with the previous readings on that machine. 11. Stop the engine. 12. Before continuing to the next test, remove the two 8T-0856 Pressure Gauges from both hose assemblies. Install a 8T-0860 Pressure Gauge with a range of 0 to 40000 kPa (0 to 5800 psi) to the hose assembly that is attached to the pressure tap (5) and to the pressure tap (4) . Note: Failure to remove the 8T-0856 Pressure Gauges prior to performing the following tests will cause the gauges to be destroyed, when the pump is upstroked.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
STICK OUT STICK IN STICK EXTEND (if equipped) STICK RETRACT (if equipped) Auxiliary (if equipped) SWING Backhoe BUCKET DUMP Backhoe BUCKET CLOSE BOOM RAISE BUCKET DUMP (parallel lift machines) 16200 700 kPa (2350 100 psi) 22800 700 kPa (3300 100 psi) 20700 700 kPa (3000 100 psi)
RACK BACK (parallel lift machines) BUCKET DUMP and RACK BACK for (S/N: FDP1-7198, BNK1-2501) BUCKET DUMP and RACK BACK for (S/N: FDP7199-UP, BNK2502-UP) BUCKET DUMP and RACK BACK (single tilt machines) LIFT 22800 700 kPa (3300 100 psi) N/A
Note: There may be air in the signal network, if there is a hesitation before reaching the relief pressure. Purge the signal lines of the air. 6. In order to check the BOOM LOWER circuit, perform the following procedure. a. Engage the boom lock. For 416D, 420D, 424D and 430D machines, run the engine at 1100 rpm. Activate the BOOM LOWER by pushing the boom control lever fully forward. For 428D, 432D, 438D and 442D machines, run the engine at 1250 rpm. Activate the BOOM LOWER by pushing the boom control lever fully forward. b. Note the pressure reading at pressure tap (4) . c. See Table 3 for the proper pressure readings at pressure port (4) .
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
Table 3 Hydraulic Circuit BOOM LOWER 420D, 428D, 430D, 432D, 438D and 442D 15200 700 kPa (2200 100 psi) 416D and 424D
7. If the machine is equipped with All Wheel Steer, perform the following procedure.
g00869579
a. Check the circuit for the All Wheel Steer by moving the All Wheel Steer switch (13) to the right.
Illustration 7 g00869580 The Independent Rear Maneuvering switches are located on the pilot operated controls. (14) Pilot operated loader control (15) Left Independent Rear Maneuvering switch (16) Right Independent Rear Maneuvering switch
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
Illustration 8 g00869582 The Independent Rear Maneuvering switches are located on the mechanically operated controls. (14) Mechanically operated loader control (15) Left Independent Rear Maneuvering switch (16) Right Independent Rear Maneuvering switch
b. Stall the rear axle by pressing the left Independent Rear Maneuvering switch (15) or the right Independent Rear Maneuvering switch (16) . c. Note the pressure reading at pressure tap (4) . d. See Table 4 for the proper pressure readings at pressure port (4) . Table 4 Hydraulic Circuit Independent Rear Maneuvering 420D, 430D, 438D and 442D 22800 700 kPa (3300 100 psi) 416D, 424D, 428D and 432D N/A
8. Turn off the engine. Engage the parking brake and remove the test equipment. 9. If the BOOM LOWER, RACK BACK or DUMP pressures are not within the specification, check the line relief valve of the suspected function. 10. If the RACK BACK or DUMP pressure is not with the specification for these machines (S/N: FDP7199-UP, BNK2502-UP), check the relief valve for the signal pressure on the tilt control valve. 11. If the pressure for any other circuit is not within the specification, the pressure compensator valve needs to be adjusted. 12. If the engine stalls, the torque limiter needs to be adjusted.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
The Relief Valve for the Tilt Cylinder (Bucket Dump and Rackback)
Refer to the following steps in order to check the pressure setting: 1. Attach 8T-0857 Pressure Gauge to the output pressure port on the hydraulic pump. 2. Start the machine. 3. Tilt the bucket to the DUMP position or tilt the bucket to the RACK BACK position. Hold the valve in the open position. Note: The valve functions when the control spool is actuated. 4. Read the pressure gauge in order to determine the relief valve setting. See table 2 for the correct pressure for your machine.
Illustration 9
g00844826
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
Compensator valve (all other machines) (1) Flow compensator (3) O-ring (4) Locknut (5) Adjustment screw (6) Cap (7) Adjustment screw (8) Cap (9) Locknut (10) O-ring (11) Pressure compensator spool (12) O-ring (13) O-ring
Note: If an adjustment is necessary, replace the O-rings (3) , (10) , (12) and (13) . Replacing the Orings will reduce the possibility of oil leakage after an adjustment to the compensator valve is made. Flow compensator valve (1) and pressure compensator valve (11) have been tested by running the pump discharge tests.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
pressure tap (4) . 8. Repeat the "High Pressure Stall Test" until the system pressure is within the specification. 9. When the pressure compensator is adjusted correctly, stop the engine. Tighten locknut (14) . Replace cap (13) and remove the gauges.
Note: The following procedure can be used in most cases when the torque limiter may be the cause of a performance problem. Note: Install a 9U-7400 Multitach to the engine. Check the low idle. The low idle must be 975 25 rpm. If the engine low idle rpm is not within the specification, then refer to Systems Operation, Testing and Adjusting, SENR5816, "3054 Engine for Caterpillar Built Machines". Perform the low idle adjustment. The engine idle must be within the specification before continuing to the next procedure. Note: Perform "Low Pressure Standby Pressure Test", "Margin Pressure Test" and "High Pressure Stall Test" prior to performing the Test for the Torque Limiter. Make the necessary adjustments in order to meet the specifications.
NOTICE
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates.
Perform the following tests before you adjust the torque limiter. Perform the test for the torque limiter on single tilt machines and parallel lift loaders. 1. Ensure that the work tool on the front of the machine and the stabilizers are on the ground. Engage the parking brake. 2. Start the engine. Run the engine at LOW idle. 3. Place the transmission in SECOND gear. Activate the front running lights. Activate the air conditioner (if equipped). 4. Engage the service brakes. 5. Perform the appropriate test. a. For single tilt machines, rack back the bucket fully and lower the bucket to the ground. Activate the LIFT circuit slowly. Note the pressure while the lift arms are moving. Do not stall the LIFT circuit. b. For parallel lift machines, dump the bucket fully and lower the bucket to the ground. Stall the DUMP circuit and activate the LIFT circuit slowly. Note the pressure while the lift arms are moving. Do not stall the LIFT circuit. 6. Stop the engine.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
7. If the engine does not stall, no adjustment to the torque limiter is necessary. 8. If the engine stalls, the torque limiter on the hydraulic pump is set too high or the engine has low power. Lower the work tool to the ground. Stop the engine and engage the parking brake. Adjust the torque limiter by performing Step 16 through Step 21 of the "Test and Adjust the Torque Limiter with a Flow Meter" procedure. Then, repeat the test procedure. If the engine stalls, adjust the fuel pump for the engine.
Note: This test should not be performed unless the "Test for the Torque Limiter" does not resolve the performance problem with the torque limiter.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
g00841651
Pump pressure tap (1) is located on hydraulic pump (2) . 1. Start the engine. Engage the parking brake. 2. Move the stick OUT. Lower all the work tools and the stabilizers to the ground. 3. Stop the engine. Move all the control levers to all positions. This releases system pressure. 4. Install one 8T-0860 Pressure Gauge with a range of 0 to 40000 kPa (0 to 5800 psi) to one end of the 177-7860 Hose Assembly . Attach the second end of the hose assembly to pump pressure tap (1) . 5. Install one 8C-3417 Elbow into each port in 4C-9910 Flow Meter . Attach one 6V-8946 Reducer Assembly onto each 8C-3417 Elbow . Attach one 6V-8943 Reducer Assembly onto one of the 6V-8946 Reducer Assemblies .
g00747372
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
6. There are two retainers (5) on the boom. Remove the two bolts from each retainer. Remove the retainers.
g00747389
7. Remove the hose (6) from the connector from the head end of the boom cylinder (7) . Install one 123-3893 Cap Assembly to connector (7) . 8. Install the hose to the head end of the boom cylinder (6) onto the 6V-8943 Reducer Assembly that was installed in Step 5.
Illustration 13 (8) Hose to the rod end of the boom cylinder (9) Tube to the rod end of the boom cylinder
g00747400
9. Remove hose (8) from the tube to the rod end of the boom cylinder (9) . Install a 6V-9831 Cap Assembly to tube (9) .
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
10. Install the end of hose (8) onto the 6V-8946 Reducer Assembly that was installed in Step 5. 11. Start the engine. Cycle the work tools until the hydraulic oil temperature on the 4C-9910 Flow Meter rises to 60 C (140 F). 12. When the hydraulic oil temperature is at 60 C (140 F), increase the engine speed to 2200 rpm. Move the boom control lever to the boom RAISE position. Hold the boom control lever in the RAISE position. Flow will decrease as rpm decreases. 13. Rotate the control knob for the pressure on the 4C-9910 Flow Meter until the pump pressure is 17,900 kPa (2600 psi) at pump pressure tap (1) . Record the flow and the oil pressure. Note: If the engine cannot maintain 2200 rpm, refer to Systems Operation, Testing and Adjusting, SENR5815, "3054 Engine for Caterpillar Built Machines". Perform the torque converter stall test and check the high idle. The engine high idle must be within the specification before continuing to the next procedure. 14. Table 6 shows the correct pump pressure and the correct flow rate for 416D and 424D machines. Table 6 PUMP PRESSURE 17900 kPa (2600 psi) FLOW 100 to 130 L/min (29 to 35 US gpm)
Table 7 shows the correct pressure and the correct flow rate for all other machines. Table 7 PUMP PRESSURE 17900 kPa (2600 psi) FLOW 120 to 140 L/min (31 to 37 US gpm)
15. If the flow is not within the specification, then the torque limiter needs to be adjusted. Lower all work tools to the ground and stop the engine. 16. Turn the engine start switch key to the ON position. 17. Move all the hydraulic hand controls through all of the positions in order to release pressure in the hydraulic system. 18. Turn the engine start switch key to the OFF position.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
g00747415
Illustration 15 (11) Locknut on the torque limiter (12) Plug on the torque limiter
g00747419
20. Loosen locknut (11) . Turn plug (12) clockwise in order to increase the flow. Turn plug (12) counterclockwise in order to decrease the flow. Note: Use FT-2812 Modified Wrench for Adjusting the Torque Limiter . Note: Take care to loosen the locknut so that the sleeve will not bind. If the bolt dislodges from the sleeve, the sleeve does not rotate. If the sleeve does not rotate, no adjustment is made. Note: Turning the plug (12) to the next flat side of the plug will change the flow approximately 7.6 L/min (2 US gpm). Never, adjust plug (12) more than three and a half of a turn. Adjusting the plug (12) more may damage the internal spring. If the spring fails, the pump performance will be poor. 21. After the adjustment is made, tighten locknut (10) .
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
22. Repeat Steps 11, 12, 13 and 14. 23. If the flow is not within the specification, then repeat Steps 20 and 21. If the torque limiter is not within the specification after several attempts, then rework the torque limiter. Go to the next test in order to Rework the Torque Limiter. Repeat the test and adjust for the torque limiter after you rework the torque limiter. 24. When the flow is within the specification in Steps 14, then proceed with the next Step. 25. Turn the engine start switch key to the ON position. 26. Move all the hydraulic hand controls through all of the positions in order to release pressure in the hydraulic system. 27. Turn the engine start switch key to the OFF position. 28. Remove the test equipment. 29. Remove hose (6) from the 6V-8946 Reducer Assembly . Remove 6V-9831 Cap Assembly from tube (5) . Place a new O-ring onto the fitting and reinstall hose (6) to tube (5) . 30. Remove hose (4) from the 6V-8946 Reducer Assembly . Remove 6V-9832 Cap Assembly from elbow (3) . Place a new O-ring onto the fitting and reinstall hose (4) to elbow (3) . 31. Replace hoses (4) and (6) into the two retainers (8) on the boom for the two hoses. Reinstall the four bolts (7) . There are two bolts on each retainer (8) . Reinstall the retainers (8) on the boom for the hoses. 32. Replace the floorplate. Reinstall the four screws that hold the floorplate in place. 33. Reinstall the four screws that hold the two plates for the floor mat. There are two screws on each plate. The plates are located at the edge of each door in the cab.
Note: If the torque limiter cannot be set within the specification, then replace the torque limiter. Note: This procedure will not increase the lifting capacity of the machine.
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates.
1. Move the machine to a level surface. 2. Lower all of the work tools to the ground. 3. Turn the engine OFF. Engage the parking brake. 4. Turn the engine start switch key to the ON position. 5. Move all the hydraulic hand controls through all of the positions in order to release pressure in the hydraulic system. 6. Turn the engine start switch key to the OFF position.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
Illustration 16 (1) Piston pump (2) Torque limiter (3) Bolts (4) Tube
g00747791
7. Clean the area around torque limiter (2) . 8. Disconnect tube (4) from torque limiter (2) . 9. Remove the two bolts (3) . Note: Use FT-2812 Modified Wrench for Adjusting the Torque Limiter . 10. Remove torque limiter (2) from pump (1) .
g00850777
11. Replace the springs (5) for the torque limiter and the O-rings for the torque limiter. 12. Clean all of the parts prior to assembly. Assemble the torque limiter. 13. Install the torque limiter (2) . 14. Install two bolts (3) . 15. Connect tube (4) to torque limiter (2) . 16. Repeat the Test for the Torque Limiter. 17. Check the hydraulic oil level. Refer to the Operation and Maintenance Manual for the proper capacity.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010
Copyright 1993 - 2010 Caterpillar Inc. Todos los derechos reservados. Red privada para licenciados del SIS.
https://10.100.28.25:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/s... 03/03/2010