Académique Documents
Professionnel Documents
Culture Documents
Customer : G/A
SAMSUNG TFT-LCD SAMSUNG TFT-LCD
NOTE :
MODEL
LTY320HM01 LTA320HM01
Doc. No
05-000-G-100316
Page
1 / 29
Contents Revision History -------------------------------------------------------------------------------------------- (3) General Description --------------------------------------------------------------------------------------- (4) General Information --------------------------------------------------------------------------------------- (4) 1. Absolute Maximum Ratings -------------------------------------------------------------------------- (5) 2. Optical Characteristics --------------------------------------------------------------------------------- (6) 3. Electrical Characteristics ------------------------------------------------------------------------------- (9) 3.1 TFT LCD Module 3.2 Back Light Unit 4. Block Diagram ------------------------------------------------------------------------------------------- (11) 5. Input Terminal Pin Assignment --------------------------------------------------------------------- (12) 5.1 Input Signal & Power 5.2 Inverter Input Pin Configuration 5.3 Inverter Input Power Sequence & Specification 5.4 LVDS Interface 5.5 Input Signals, Basic Display Colors and Gray Scale of Each Color 6. Interface Timing ---------------------------------------------------------------------------------------- (19) 7.1 Timing Parameters (DE only mode) 7.2 Timing Diagrams of interface Signal (DE only mode) 7.3 Power ON/OFF Sequence 7. Outline Dimension -------------------------------------------------------------------------------------- (22) 8. Packing ------------------------------------------------------------------------------------------------- (24)
9. Marking & Others ------------------------------------------------------------------------------------- (26) 10. General Precaution ---------------------------------------------------------------------------------- (27) 10.1 Handling 10.2 Storage 10.3 Operation 10.4 Operation Condition Guide 10.5 Others
MODEL
LTY320HM01 LTA320HM01
Doc. No
05-000-G-100316
Page
2 / 29
* Revision History
Date Mar. 16, 2010 Rev. No Page Summary
000
First Issued
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
3 / 29
General Description
Description LTY320HM01 LTA320HM01 is a color active matrix liquid crystal display (LCD) that uses amorphous silicon TFT(Thin Film Transistor) as switching components. This model is composed of a TFT LCD panel, a driver circuit and a back light unit. The resolution of a 32.0 is 1920 x 1080 and this model can display up to 16.7million colors with wide viewing angle of 89 or higher in all directions. This panel is intended to support applications to provide a excellent performance for Flat Panel Display such as Home-alone Multimedia TFT-LCD TV, Display terminals for AV application products, and High Definition TV (HDTV). Features RoHS compliance (Pb-free) High contrast ratio, high aperture ratio, fast response time SPVA (Super Patterned Vertical Align) mode Wide viewing angle (89) Full HD (1920 x 1080 pixels) resolution (16:9) Low Power consumption 4 CCFTs (Cold Cathode Fluorescent Tube) LVDS (Low Voltage Differential Signaling) interface
General Information
Items Module Size Weight Pixel Pitch Active Display Area Surface Treatment Display Colors Number of Pixels Pixel Arrangement Display Mode Luminance of White Specification 960(HTYP) x 450(VTYP) 57.2(DMAX) 6000(Max) 0.12125(H) * 3 x 0.36375(V) 698.4(H) x 392.85(V) Haze 7%, Hard-coating (3H) 8 bit- 16.7M 1920 x 1080 RGB vertical stripe Normally Black
450
Unit mm g mm mm
Note 1.0mm
colors pixel
cd/m2
Typ.
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
4 / 29
Note (1) Ta= 25 2 C (2) Temperature and relative humidity range are shown in the figure below. a. 93.8 % RH Max. (Ta 40 C) b. Maximum wet-bulb temperature at 40 C or less. (Ta 40 C) c. No condensation (3) Polarizer will not be damaged in this range, even though abnormal visual problems occur in TSUR range. (4) 11ms, sine wave, one time for X, Y, Z axis (5) 10-300 Hz, Sweep rate 10min, 30min for X,Y,Z axis
(40, 93.8)
(50, 50.4)
(65, 27.7)
Fig. Temperature and Relative humidity range MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 5 / 29
2. Optical Characteristics
The optical characteristics should be measured in a dark room or equivalent. Measuring equipment : TOPCON BM-7,SPECTRORADIOMETER SR-3
(Ta = 25 2C, VDD=12V, fv= 60Hz, fDCLK=148.5MHz, Dim = 100%)
Item Contrast Ratio (Center of screen) Rising Response Time Falling G-to-G [AVE] Symbol C/R Tr Tf Tg YL Rx Ry Gx Gy Bx By Wx Wy Hor. Viewing Angle Ver. Brightness Uniformity (9 Points) L R U D Buni C/R10 79 79 79 79 Normal L,R=0 U,D=0 Viewing Angle TYP. -0.03 Condition Min. *2500 380 Typ. 5000 12 8 8 450 0.639 0.330 0.288 0.604 0.148 0.057 0.280 0.285 72 10000 2.2 89 89 89 89 25 % (4) SR-3 Degree (8) SR-3 % K (7) SR-3 (7) SR-3 TYP. +0.03 (7),(8) SR-3 Max. 70 18 cd/m2 (6) SR-3 msec (5) BM-7 Unit Note (3) SR-3
Green
Blue
* marked Items Value does not Specification above when White stain occurs at Center Point [Point of Note 2.]
Note (1) Test Equipment Setup The measurement should be executed in a stable, windless and dark room between 40min and 60min after lighting the back light at the given temperature for stabilization of the back light. This should be measured in the center of screen. Single lamp current @ Vdim = 100% Environment condition : Ta = 25 2 C
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
6 / 29
Field 1 2
Photo detector
Field
540
900
Note (3) Definition of Contrast Ratio (C/R) : Ratio of gray max (Gmax) & gray min (Gmin) at the center point of the panel
C/R
G max G min
Gmax : Luminance with all pixels white Gmin : Luminance with all pixels black
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
7 / 29
Buni 100
Bmax : Maximum brightness Bmin : Minimum brightness Note (5) Definition of Response time : Sum of Tr, Tf Display data
Black (data off) White (data on) White (data off)
TF
10% 0% TIME Note (6) Definition of Luminance of White : Luminance of white at center point Note (7) Definition of Color Chromaticity (CIE 1931) Color coordinate of Red, Green, Blue & White at center point Note (8) Definition of Viewing Angle : Viewing angle range (C/R 10)
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
8 / 29
3. Electrical Characteristics
3.1 TFT LCD Module
The connector for display data & timing signal should be connected. Ta = 25C 2 C
Item Voltage of Power Supply (a) Black Current of Power Supply (b) White (c) Mosaic (4) Max Pattern Vsync Frequency Hsync Frequency Main Frequency Rush Current fV fH fDCLK IRUSH IDD Symbol VDD Min. 11 47 50 130 Typ. 12 450 700 700 750 60 67.5 148.5 Max. 13 900 950 62 73 155 5 Hz kHz MHz A (4) mA (2),(3) Unit V Note (1)
Note (1) The ripple voltage should be controlled under 10% of VDD. (2) fV=60Hz, fDCLK = 148.5MHz, VDD = 12.0V, DC Current. (3) Power dissipation check pattern (LCD Module only) a) Black Pattern b) White Pattern c) Mosaic d)Max. Pattern
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
9 / 29
Note (1) It is defined as the time to take until the brightness reduces to 50% of its original value. [Operating condition : Ta = 252, IL = 14.0 mArms(typ.), For single lamp only. ]
Socket
HOT 1 HOT 1
Inverter
LCD Module
HOT 4 HOT 4
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
10 / 29
4. Block Diagram
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
11 / 29
Connector : IS050-C51B-C38(UJU)
Compatible with FI-RE51S-HF(JAE)
PIN No. 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 Signal LVE[0]P LVE[1]N LVE[1]P LVE[2]N LVE[2]P GND LVECLKLVECLK+ GND LVE[3]N LVE[3]P N.C. N.C. GND SCL SDA VSYNC B-INT N.C. N.C. LUT SEL0 LUT SEL1 LUT SEL2 HSYNC TCON_RDY SEL1 Description Even LVDS Signal + Even LVDS Signal Even LVDS Signal + Even LVDS Signal Even LVDS Signal + GND Even LVDS ClockEven LVDS Clock+ GND Even LVDS Signal Even LVDS Signal + No Connection No Connection GND I2C SCL I2C SDA *V Sync Signal Bus Release No Connection No Connection DCC LUT Select 0 DCC LUT Select1 DCC LUT Select2 H Sync Signal T-Con Ready SEC Internal Use Only
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
12 / 29
Description ( Based on DCC On) Pin N.O. 48 0 0 0 Select bit 0 1 1 1 1 TCON Ready Operation Low High High Low Description Normal Operation Error Operation 47 0 0 1 1 0 0 1 1 46 LUT 0 1 0 1 0 1 0 0% 1 For 60Hz For 60Hz For 60Hz @ Low Temp. For 60Hz @ Low Temp. For 50Hz For 50Hz %(For Interpolate) 100%
100%X1.25 100%X1.25 (100%X1.25) X 1.25 100% 100%X1.25
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
13 / 29
PCB
#1
#51
connect name
#1 #51
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
14 / 29
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
15 / 29
Note 2. There are not shut down and flicker at 10% @ 150Hz. There is not shut down at 5% @ 75Hz. Note 3. Measurement Method : Check Vs on BLU Remaining all Lamps.
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
16 / 29
Odd Data
R2 R3 R4 R5 R6 R7 G2 G3 G4 G5 G6 G7 B2 B3 B4 B5 B6 B7 HSYNC VSYNC DEN R0 R1 G0 G1 B0 B1 Reserved
Even Data
R2 R3 R4 R5 R6 R7 G2 G3 G4 G5 G6 G7 B2 B3 B4 B5 B6 B7 HSYNC VSYNC DEN R0 R1 G0 G1 B0 B1 Reserved
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
17 / 29
5.5 Input Signals, Basic Display Colors and Gray Scale of Each Color
DATA SIGNAL COLOR DISPLAY (8bit) R0 BLACK BLUE GREEN BASIC COLOR CYAN RED MAGENTA YELLOW WHITE BLACK 0 0 0 0 1 1 1 1 0 1 DARK 0 : : 1 0 RED BLACK 1 0 0 DARK 0 : : 0 0 GREEN BLACK 0 0 0 DARK 0 : : 0 0 BLUE 0 R1 0 0 0 0 1 1 1 1 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 R2 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 RED R3 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 R4 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 R5 0 0 0 0 1 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 R6 0 0 0 0 1 1 1 1 0 0 0 R7 0 0 0 0 1 1 1 1 0 0 0 GREEN G0 G1 G2 G3 G4 G5 G6 G7 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 1 0 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1 B1 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 B2 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 BLUE B3 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 B4 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 B5 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B6 0 1 0 1 0 1 0 1 0 0 0 B7 0 1 0 1 0 1 0 1 0 0 0 R0 R1 R2 R3~ R252 R253 R254 R255 G0 G1 G2 G3~ G252 G253 G254 G255 B0 B1 B2 B3~ B252 B253 B254 B255 GRAY SCALE LEVEL
LIGHT
LIGHT
LIGHT
Note) Definition of Gray : Rn : Red Gray, Gn : Green Gray, Bn : Blue Gray (n = Gray level) Input Signal : 0 = Low level voltage, 1 = High level voltage
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
18 / 29
6. Interface Timing
6.1 Timing Parameters ( DE only mode )
SIGNAL Clock Hsync Vsync Active Display Period Vertical Total Active Display Period Horizontal Total Frequency ITEM SYMBOL 1/TC FH FV TVD MIN. 130 50 47 TYP. 148.5 67.5 60 1080 MAX. 155 73 62 Unit MHz KHz Hz lines NOTE -
TVB
1100
1125
1480
Lines
THD
1920
clocks
TH
2154
2200
2450
clocks
Note) This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal operation. (1) Test Point : TTL control signal and CLK at LVDS Tx input terminal in system (2) Internal VDD = 3.3V
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
19 / 29
DE
TH THD
DE
DCLK
TC
DATA SIGNALS
TC TCH TCL
DCLK
TDS TDH
0.5 VCC
DISPLAY DATA
TES
0.5 VCC
DE
0.5 VCC
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
20 / 29
[UNIT : mS] Min T1 T2 T3 T4 T5 T6 T7 0.47 0 0 0.1 220 0 0 Max 30 100 100 50 350 30 30 T8 T9 T10 T11 T12 T13 T14 Min 30 500 50 100 0 0 1000 Max 50 300 -
The supply voltage of the external system for the Module input should be the same as the definition of VDD. Apply the lamp voltage within the LCD operation range. When the back light turns on before the LCD operation or the LCD turns off before the back light turns off, the display may momentarily show abnormal screen. In case of VDD = off level, please keep the level of input signals low or keep a high impedance. T14 should be measured after the Module has been fully discharged between power off and on period. Interface signal should not be kept at high impedance when the power is on.
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
21 / 29
MODEL
LTA320HM01 LTY320HM01
Doc. No
05-000-G-100316
Page
22 / 29
MODEL
LTY320HM01 LTA320HM01
Doc. No
05-000-G-100316
Page
23 / 29
8. PACKING
Applied to SESL, SESL LCM Model 8.1 CARTON (Internal Package)
(1) Packing Form Corrugated fiberboard box and corrugated cardboard as shock absorber (2) Packing Method
Packing Box
Module(26EA)
Desiccant (Drier) Pallet Packing Direction Total Pallet Size Total Pallet Weight
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
24 / 29
LCD Packing
24 ea / (PackingPallet Box)
Desiccant (Drier) Pallet Packing Direction Total Pallet Size Total Pallet Weight
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
25 / 29
LTY320HM01 LTA320HM01
XXXXXX
XXXXXXXXXX
40mm
Revision code
LTA320HM01 LTY320HM01XXX
Lot number
80mm
LTY320HM01-XXX LTA320HM01
XXXX
xx
100mm
Part number
Revision code Actual Quantity
0703
(6) Others 1. After service part Lamps cannot be replaced because of the narrow bezel structure. MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 26 / 29
10.2 Storage
(a) Do not leave the Module in high temperature, and high humidity for a long time. It is highly recommended to store the Module with temperature from 0 to 35 and relative humidity of less than 70%. (b) Do not store the TFT-LCD Module in direct sunlight. (c) The Module should be stored in a dark place. It is prohibited to apply sunlight or fluorescent light in storing.
10.3 Operation
(a) No Connection or disconnect the Module in the "Power On" condition. (b) Power supply should always be turned on/off by the "Power on/off sequence" (c) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference should be done by system manufacturers. Grounding and shielding methods may be important to minimize the interference. (d) The cable between the back light connector and its inverter power supply should be connected directly with a minimized length. A longer cable between the back light and the inverter may cause lower luminance of lamp(CCFT) and may require higher startup voltage(Vs).
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
28 / 29
10.5 Others
(a) Ultra-violet ray filter is necessary for outdoor operation. (b) Avoid condensation of water. It may result in improper operation or disconnection of electrode. (c) Do not exceed the absolute maximum rating value. ( supply voltage variation, input voltage variation, variation in part contents and environmental temperature, and so on) Otherwise the Module may be damaged. (d) If the Module keeps displaying the same pattern for a long period of time, the image may be "sticked" to the screen. To avoid image sticking, it is recommended to use a screen saver. (e) This Module has its circuitry PCB's on the rear side and should be handled carefully in order not to be stressed. (f) Please contact SEC in advance when you display the same pattern for a long time.
MODEL
LTY320HM01
Doc. No
05-000-G-100316
Page
29 / 29