Académique Documents
Professionnel Documents
Culture Documents
FOREWORD
DET NORSKE VERITAS (DNV) is an autonomous and independent foundation with the objectives of safeguarding life, property and the environment, at sea and onshore. DNV undertakes classification, certification, and other verification and consultancy services relating to quality of ships, offshore units and installations, and onshore industries worldwide, and carries out research in relation to these functions. DNV service documents consist of amongst other the following types of documents: Service Specifications. Procedual requirements. Standards. Technical requirements. Recommended Practices. Guidance. The Standards and Recommended Practices are offered within the following areas: A) Qualification, Quality and Safety Methodology B) Materials Technology C) Structures D) Systems E) Special Facilities F) Pipelines and Risers G) Asset Operation H) Marine Operations J) Cleaner Energy
O) Subsea Systems
The electronic pdf version of this document found through http://www.dnv.com is the officially binding version Det Norske Veritas Any comments may be sent by e-mail to rules@dnv.com For subscription orders or information about subscription terms, please use distribution@dnv.com Computer Typesetting (Adobe Frame Maker) by Det Norske Veritas
If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 2 million. In this provision "Det Norske Veritas" shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas.
Summary of Changes and Current Document Status, October 2010 Contents Page 3
CONTENTS
Sec. 1 Sec. 2 Sec. 3 General ................................................................................................................................................ 4 Current Service Specifications, Standards and Recommended Practices .................................... 6 Summary of Changes ......................................................................................................................... 9
A. Changes to DNV Service Specifications ........................................................................................................................ 9 B. Changes to DNV Standards .......................................................................................................................................... 10 C. Changes to Recommended Practices ............................................................................................................................ 14
Summary of Changes and Current Document Status, October 2010 Sec.1 Page 4
SECTION 1 GENERAL
Electronic binding versions As of October 2010, we are introducing two new DNV service document types to be used for services that are not limited to offshore and/or not to be considered as DNV Rules for classification of Ships or HSLC/NSC. The documents have been named; DNV Service Specifications (DSS) and DNV Standards (DS). Additionally, as of October 2010 all DNV service documents are primarily published electronically. The electronic pdf versions of the documents found through http://www.dnv.com are the officially binding versions. In order to initiate and ensure a practical transition from the OSS/OS to DSS/DS scheme for relevant documents and print scheme to the electronic scheme the following has been done:, All documents that should be transferred without further change in content to the new document types DSS or DS and those having incorporated amendments and corrections more recent than the date of the latest printed issue, have been renamed as relevant and given the date October 2010. Except the already incorporated amendments and corrections, no other changes have been made to the documents. The applicable documents are shown in the table below.
List of documents given the date October 2010 due to new service document types available and electronic transition Service Specifications DNV-OSS-302 Offshore Riser Systems DNV-OSS-305 Rules for Certification and Verification of Diving Systems DNV-OSS-308 Verification of Lifting Appliances for the Oil and Gas Industry DNV-OSS-309 Verification, Certification and Classification of Gas Export and Receiving Terminals DNV-OSS-401 Technology Qualification Management DNV-DSS-314 Verification of Hydrocarbon Refining and Petrochemical Facilities DNV-DSS-315 Verification of Onshore LNG and Gas Facilities Standards DNV-OS-C501 Composite Components DNV-OS-C502 Offshore Concrete Structures DNV-OS-C503 Concrete LNG Terminal Structures and Containment Systems DNV-OS-E402 Offshore Standard for Diving Systems DNV-OS-F101 Submarine Pipeline Systems DNV-OS-F201 Dynamic Risers DNV-OS-J101 Design of Offshore Wind Turbine Structures DNV-DS-J102 Design and Manufacture of Wind Turbine Blades, Offshore and Onshore Wind Turbines Recommended Practices DNV-RP-B401 Cathodic Protection Design DNV-RP-C103 Column Stabilised Units DNV-RP-C201 Buckling Strength of Plated Structures DNV-RP-C202 Buckling Strength of Shells DNV-RP-C204 Design against Accidental Loads DNV-RP-C205 Environmental Conditions and Environmental Loads DNV-RP-C206 Fatigue Methodology of Offshore Ships DNV-RP-C207 Statistical Representation of Soil Data DNV-RP-E402 Naval Rescue Submersibles DNV-RP-E403 Hyperbaric Evacuation Systems DNV-RP-F101 Corroded Pipelines DNV-RP-F102 Pipeline Field Joint Coating and Field Repair of Linepipe Coating DNV-RP-F103 Cathodic Protection of Submarine Pipelines by Galvanic Anodes DNV-RP-F106 Factory Applied External Pipeline Coatings for Corrosion Control DNV-RP-F107 Risk Assessment of Pipeline Protection DNV-RP-F109 On-Bottom Stability Design of Submarine Pipelines DNV-RP-F111 Interference Between Trawl Gear and Pipelines DNV-RP-F202 Composite Risers DNV-RP-F204 Riser Fatigue DNV-RP-F205 Global Performance Analysis of Deepwater Floating Structures DNV-RP-G101 Risk Based Inspection of Offshore Topsides Static Mechanical Equipment
Summary of Changes and Current Document Status, October 2010 Page 5 Sec.1
Update Scheme The update scheme of the documents is as follows: 1) Whenever revised, or undergoing significant editorial changes, a document will be given a new edition date and the main changes will be described on Page 3 of that document. The corresponding Adobe PDF file will be made available through http://www.dnv.com/resources/rules_standards/ and the date of the Current edition column of Table 1 in Sec.2 will be updated. 2) If, at a later date, the need arises for insignificant editorial corrections to the document, the electronic file will be updated, but the edition date will be retained. However, a new Adobe PDF file will be generated and made available through http://www.dnv.com/resources/rules_standards/. The date of the PDF file will appear in the Editorial corrections column of Table 1 in Sec.2. Discontinued updating of the Amendments and Corrections document As a result of moving away from the Print scheme there is no longer need for a separate Amendments and corrections document which intention was to supply buyers of printed documents with a detailed view of amendments to the documents applicable after issued in print. The electronic PDF files are now the officially binding versions and will always be kept current and downloadable. Readers of documents are encouraged to regularly check for updates in order to ensure that they hold the current updated versions.
Summary of Changes and Current Document Status, October 2010 Sec.2 Page 6
Table 1 Current Documents Current edition Service Specifications DNV-OSS-101 Rules for Classification of Offshore Drilling and Support Units DNV-OSS-102 Rules for Classification of Floating Production, Storage and Loading Units DNV-OSS-103 Rules for Classification of LNG/LPG Floating Production and Storage Units or Installations DNV-OSS-121 Classification based on Performance Criteria Determined from Risk Assessment Methodology DNV-OSS-201 Verification for Compliance with Norwegian Shelf Legislation DNV-OSS-202 Verification for Compliance with UK Shelf Regulations DNV-OSS-300 Risk Based Verification DNV-OSS-301 Certification and Verification of Pipelines DNV-OSS-302 Offshore Riser Systems DNV-OSS-304 Risk Based Verification of Offshore Structures DNV-OSS-305 Rules for Certification and Verification of Diving Systems DNV-OSS-306 Verification of Subsea Facilities DNV-OSS-307 Verification of Process Facilities DNV-OSS-308 Verification of Lifting Appliances for the Oil and Gas Industry DNV-OSS-309 Verification, Certification and Classification of Gas Export and Receiving Terminals DNV-OSS-312 Certification of Tidal and Wave Energy Converters DNV-OSS-313 Pipe Mill and Coating Yard - Qualification DNV-DSS-314 Verification of Hydrocarbon Refining and Petrochemical Facilities DNV-DSS-315 Verification of Onshore LNG and Gas Facilities DNV-OSS-401 Technology Qualification Management Standards DNV-OS-A101 Safety Principles and Arrangement DNV-OS-B101 Metallic Materials DNV-OS-C101 Design of Offshore Steel Structures, General (LRFD method) DNV-OS-C102 Structural Design of Offshore Ships DNV-OS-C103 Structural Design of Column Stabilised Units (LRFD method) DNV-OS-C104 Structural Design of Self-elevating Units (LRFD method) DNV-OS-C105 Structural Design of TLPs (LRFD method) DNV-OS-C106 Structural Design of Deep Draught Floating Units/Spars (LRFD and WSD Method) DNV-OS-C107 Structural Design of Ship-shaped Drilling and Well Service Units DNV-OS-C201 Structural Design of Offshore Units (WSD method) DNV-OS-C301 Stability and Watertight Integrity DNV-OS-C401 Fabrication and Testing of Offshore Structures DNV-OS-C501 Composite Components DNV-OS-C502 Offshore Concrete Structures DNV-OS-C503 Concrete LNG Terminal Structures and Containment Systems DNV-OS-D101 Marine and Machinery Systems and Equipment DNV-OS-D201 Electrical Installations DNV-OS-D202 Automation, Safety, and Telecommunication Systems DNV-OS-D203 Integrated Software-Dependent System (Tentative Standard) DNV-OS-D301 Fire Protection DNV-OS-E101 Drilling Plant DNV-OS-E201 Oil and Gas Processing Systems DNV-OS-E301 Position Mooring DNV-OS-E302 Offshore Mooring Chain DNV-OS-E303 Offshore Mooring Fibre Ropes DNV-OS-E304 Offshore Mooring Steel Wire Ropes October 2010 October 2010 October 2008 October 2008 April 2010 October 2008 April 2004 October 2000 October 2010 October 2006 October 2010 June 2004 June 2004 October 2010 October 2010 October 2008 April 2009 October 2010 October 2010 October 2010 October 2010 April 2009 October 2008 October 2008 October 2008 October 2008 October 2008 October 2008 October 2008 October 2008 October 2010 October 2010 October 2010 October 2010 October 2010 October 2010 October 2008 October 2008 April 2010 October 2008 October 2009 October 2010 October 2010 October 2008 October 2010 April 2009 Editorial corrections October 2009 April 2010 October 2009 October 2009 April 2009 October 2009 October 2009 October 2009 October 2009 October 2009 October 2009 October 2009 October 2009
Summary of Changes and Current Document Status, October 2010 Page 7 Sec.2
Table 1 Current Documents (Continued) Current edition October 2008 October 2010 October 2008 April 2010 October 2010 October 2010 October 2010 October 2010 Editorial corrections October 2009
Helicopter Decks Offshore Standard for Diving Systems Offshore Loading Buoys Design of Free Fall Lifeboats Submarine Pipeline Systems Dynamic Risers Design of Offshore Wind Turbine Structures Design and Manufacture of Wind Turbine Blades, Offshore and Onshore Wind Turbines DNV-OS-J201 Offshore Substations for Wind Farms October 2009 DNV-OS-J301 Standard for Classification of Wind Turbine Installation Units October 2010 Recommended Practices DNV-RP-A201 Plan Approval Documentation Types Definitions October 2010 DNV-RP-A203 Qualification Procedures for New Technology September 2001 DNV-RP-B101 Corrosion Protection of Floating Production and Storage Units April 2007 DNV-RP-B401 Cathodic Protection Design October 2010 DNV-RP-C101 Allowable Thickness Diminution for Hull Structure of Offshore Ships April 2007 DNV-RP-C102 Structural Design of Offshore Ships February 2002 DNV-RP-C103 Column Stabilised Units October 2010 DNV-RP-C201 Buckling Strength of Plated Structures October 2010 DNV-RP-C202 Buckling Strength of Shells October 2010 DNV-RP-C203 Fatigue Design of Offshore Steel Structures April 2010 DNV-RP-C204 Design against Accidental Loads October 2010 DNV-RP-C205 Environmental Conditions and Environmental Loads October 2010 DNV-RP-C206 Fatigue Methodology of Offshore Ships October 2010 DNV-RP-C207 Statistical Representation of Soil Data October 2010 DNV-RP-D101 Structural Analysis of Piping Systems October 2008 DNV-RP-D201 Integrated Software Dependent Systems October 2009 DNV-RP-E101 Recertification of Well Control Equipment October 2008 DNV-RP-E102 Recertification of Blowout Preventers and Well Control Equipment for the US June 2010 Outer Continental Shelf DNV-RP-E301 Design and Installation of Fluke Anchors in Clay 2000 DNV-RP-E302 Design And Installation of Plate Anchors in Clay December 2002 DNV-RP-E303 Geotechnical Design and Installation of Suction Anchors in Clay October 2005 DNV-RP-E304 Damage Assessment of Fibre Ropes for Offshore Mooring April 2005 DNV-RP-E401 Survey of Diving Systems April 2007 DNV-RP-E402 Naval Rescue Submersibles October 2010 DNV-RP-E403 Hyperbaric Evacuation Systems October 2010 DNV-RP-F101 Corroded Pipelines October 2010 DNV-RP-F102 Pipeline Field Joint Coating and Field Repair of Linepipe Coating October 2010 DNV-RP-F103 Cathodic Protection of Submarine Pipelines by Galvanic Anodes October 2010 DNV-RP-F105 Free Spanning Pipelines February 2006 DNV-RP-F106 Factory Applied External Pipeline Coatings for Corrosion Control October 2010 DNV-RP-F107 Risk Assessment of Pipeline Protection October 2010 DNV-RP-F108 Fracture Control for Pipeline Installation Methods Introducing January 2006 Cyclic Plastic Strain DNV-RP-F109 On-Bottom Stability Design of Submarine Pipelines October 2010 DNV-RP-F110 Global Buckling of Submarine Pipelines October 2007 Structural Design due to High Temperature/High Pressure DNV-RP-F111 Interference Between Trawl Gear and Pipelines October 2010 DNV-RP-F112 Design of Duplex Stainless Steel Subsea Equipment Exposed to October 2008 Cathodic Protection DNV-RP-F113 Pipeline Subsea Repair October 2007 DNV-RP-F116 Integrity Management of Submarine Pipeline Systems October 2009 DNV-RP-F118 Pipe Girth Weld Aut System Qualification and Project Specific Procedure October 2010 Validation DNV-RP-F201 Design of Titanium Risers October 2002 DNV-RP-F202 Composite Risers October 2010 DNV-RP-F203 Riser Interference April 2009
Summary of Changes and Current Document Status, October 2010 Sec.2 Page 8
Table 1 Current Documents (Continued) Current edition October 2010 October 2010 April 2008 April 2007 April 2010 October 2010 October 2007 January 2003 April 2004 April 2010 April 2010 April 2010 April 1985 2005 Editorial corrections 2007
DNV-RP-F204 DNV-RP-F205 DNV-RP-F206 DNV-RP-F301 DNV-RP-F302 DNV-RP-G101 DNV-RP-G103 DNV-RP-H101 DNV-RP-H102 DNV-RP-H103 DNV-RP-J201 DNV-RP-J202
Riser Fatigue Global Performance Analysis of Deepwater Floating Structures Riser Integrity Management Subsea Separator Structural Design Selection and Use of Subsea Leak Detection Systems Risk Based Inspection of Offshore Topsides Static Mechanical Equipment Non-intrusive Inspection Risk Management in Marine and Subsea Operations Marine operations during Removal of Offshore Installations Modelling and Analysis of Marine Operations Qualification Procedures for CO2 Capture Technology Design and Operation of CO2 Pipelines
DNV-RP-O401 Safety and Reliability of Subsea Systems DNV-RP-O501 Erosive Wear in Piping Systems
Summary of Changes and Current Document Status, October 2010 Page 9 Sec.3
DNV-OSS-102
DNV-DSS-314
Verification of Hydrocarbon Refining and Petrochemical Facilities Verification of Onshore LNG and Gas Facilities
DNV-DSS-315
Summary of Changes and Current Document Status, October 2010 Sec.3 Page 10
DNV-OS-D101
Summary of Changes and Current Document Status, October 2010 Page 11 Sec.3
Main changes C. Design Conditions: Table C5 giving permissible stresses with reference to DNV specific steel qualities has been deleted and new reference made to recognized standards in DNV-OS-B101, in line with Rules for classification of ships Pt.4 Ch.6 Requirements for Thermal expansion stresses, Documentation of thermal stress calculation, Stress calculation and Table C6 included in line with Rules for classification of ships Pt.4 Ch.6 Requirements to plastic pipes revised to be in line with Rules for classification of ships Pt.4 Ch.6. E. Valves: Requirement to valve design revised in line with Rules for classification of ships Deleted requirement regarding screw-on valve bonnets. F. Flexible Hoses: The requirements for flexible hoses have been revised in line with Rules for classification of ships and IACS UR P2 2.12. G. Detachable Pipe Connections: The requirements for detachable pipe connections have been revised in line with Rules for classification of ships and IACS UR P2 2.12. Inserted Table G2 and G3. H. Socket Welded Joints and Slip-on Sleeve Welded Joints: Use of slip-on sleeve welded joints in overboard pipes restricted in line with Rules for classification of ships Pt.4 Ch.6. Ch.2 Sec.3 B. Ballast, Bilge and Drainage Systems General: Deleted general capacity requirement. F. Air, Overflow and Sounding Pipes: Vent for lub. oil tanks revised in line with Rules for classification of ships Pt.4 Ch.6 Requirement to overflow pipes and short sounding pipes revised in line with Rules for classification of ships Pt.4 Ch.6. Ch.2 Sec.4 A. General: Added new sub-section element A100 Scope. B. Cooling System: Included requirements for combined cooling water/fuel oil heating systems, and sea chest arrangement for class notations for navigation in ice, in line with Rules for classification of ships Pt.4 Ch.6. D. Fuel Oil System: Included acceptance criteria for use of oil fuels with a flash point less than 60C, in line with Rules for classification of ships Pt.4 Ch.6 Valve arrangement on fuel oil tanks revised in line with Rules for classification of ships Pt.4 Ch.6 and SOLAS Ch.II-2 Requirements to remote stop of fuel oil pumps and fans deleted since they are already stated in DNV-OS-D201. G. Steam Systems: Included requirements to blow down valves on unit's side in line with Rules for classification of ships Pt.4 Ch.6. H. Hydraulic Systems: Requirements to hydraulic cylinders are deleted and reference made to DNV Standards for Certification No. 2.9 (Approval Program No.5778.93). I. Pneumatic Power Supply: Revised in line with Rules for classification of ships Pt.4 Ch.6.
Summary of Changes and Current Document Status, October 2010 Sec.3 Page 12
Main changes J. Pneumatic Starting Arrangements: Revised in line with Rules for classification of ships Pt.4 Ch.6 and experience feedback. Included requirement to fire pump drivers. K. Heating, Ventilation and Air Conditioning (HVAC): Added requirement for installation of electrical fan motors installed in ventilation ducts for hazardous spaces, in line with Rules for classification of ships Pt.5 Ch.3 Safety requirements for Refrigeration plants revised to be applicable for plants with total prime mover effect of 100W and above, in line with Rules for classification of ships Pt.4 Ch.1. L. Use of Gas and Crude Oil for Auxiliary Boilers and Turbines: Reference to DNV-OS-E201 also applicable for gas fuelled boilers. Ch.2 Sec.5 B. Recognised Codes and Standards: Deleted reference to recognized codes and standards. C. General Marine Equipment: Clarified that for certification of machinery and equipment with similar application as for ships, requirements as given in the Rules for Classification of Ships will be applicable. Recognised international standards may be used on a case by case basis. Ch.3 Sec.1 C. Certification of Materials and Components: Included certification requirements for hydraulic cylinders in Table C2 Table C5 updated in line with Rules for classification of ships Pt.4 Ch.6 Requirement to certification of compressors revised to be in line with Ship Rules. E. Survey During Installation and Commissioning: Deleted requirement that commissioning procedures shall be approved. Further, added some text clarifying DNVs involvement with commissioning. Offloading systems: Requirements for offloading systems updated and expanded. Moved to a new separate Ch.2 Sec.12, stipulating requirements to design of arrangement, safety & control systems, hoses and hawsers of offloading systems. Introducing a new voluntary class notation OFFLOADING, granted to units complying with Ch.2 Sec.12 of the revised DNV-OS-E201. Requirements for equipment certification - relevant for the OFFLOADING notation introduced in Ch.3. Ch.2 Sec.9 Materials and Corrosion Protection completely re-written for improved alignment with recognised industry codes and practice. General updating of references and editorial improvements based on experience feed-back from users. Ch.2 Sec.1 B306: Included a definition of extreme value for mooring line tensions during a squall event. B700: Adjusted the required drag coefficients for steel wire ropes. Ch.2 Sec.2 B101: Added fibre rope degradation method. B110 (previous item B106): updated guidance regarding e-modules of studless chain based on information from VICINAY. E201: Updated Table E1 with respect to in-service assessment. F800: Requirements to investigate the possibility of VIM on steel wire and fibre ropes included. If VIM is a possible load effect, the effect shall be included in fatigue assessment.
DNV-OS-E201
DNV-OS-E301
Position Mooring
Summary of Changes and Current Document Status, October 2010 Page 13 Sec.3
Main changes Ch.2 Sec.4 Sub-section J, Added 103 and 200: design criteria for fibre ropes and yarn for fibre ropes. Q105: Added requirement to measuring ranges for tension measuring equipment. R403: Added design requirement to element between MLBE and mooring line. Ch.2 Sec.5 A100: Added requirements for anchor shackles for mobile mooring that are not of R-quality. Ch.3 Sec.1 B100: Added that temporary mooring is not a class requirement for DP units with DYNPOS-AUTR or AUTRO notations. Towing arrangements for ship shaped units shall be according to DNV Rules for Classification of Ships. D602: It is emphasized that it is the technical part of the standard that could be replaced by e.g. API RP2SK and ISO 19901-7, and that equipment and material shall be certified by DNV. Ch.3 Sec.2
DNV-OS-E303
DNV-DS-J102
DNV-OS-J301
A200: Chain qualities R4S and R5 are included in the standard. G200: Requirements added regarding in-service condition assessment for fibre ropes. Offshore Mooring Fibre Definitions of terms have been updated. Ropes This standard now presents three certificate formats, ropes for Long-Term -, ropes for Mobile Moorings and one for thimbles. Approval of Manufacturer schemes for fibre rope manufacturers and load bearing yarn manufacturers are introduced. Testing procedure for load bearing yarns is introduced The structure of each chapter is reorganized in order to separate the applicable requirements to long term mooring and. mobile mooring. The scope of testing for mobile mooring is brought in line with ISO 18962, whilst for long term moorings the principle of application of specific mooring systems performance is reinforced. Rules for hardware (thimbles) have been clarified. Testing methods, which are subject to approval, have been removed from Ch.2 Sec.3. The previous Appendixes A, B, C and D on Fibre rope stretch and stiffness, Measuring and Expressing the Rope Change-in-Length Properties, Changein-length test methods for long-term mooring and Quality review report have been removed. The term soil barrier is replaced by filter, as this is the commonly used term in other standards. Added a new Appendix A containing scope of survey for fibre-rope production. Design and Manufacture of This service specification; DS-J102: Design and Manufacture of Wind Turbine Wind Turbine Blades, Off- Blades, Offshore and Onshore Wind Turbines replaces the previous version of the shore and Onshore Wind document with short name; DNV-OS-J102. There are no changes in content, only Turbines how the document is referred to, as OS now will be used for Standards intended for Offshore use. Standard for Classification This new DNV Offshore Standard provides special technical requirements for units which are purpose built for installation/maintenance of Offshore Wind Turbine. of Wind Turbine The standard supports the special service notation Wind Turbine Installation Installation Units Unit which was introduced through the DNV-OSS-101 in October 2009.
Summary of Changes and Current Document Status, October 2010 Sec.3 Page 14
In addition documentation types M081, M083 and M084 have been amended. This new document provides a uniform guideline for the general qualification of Automated Ultrasonic Testing (AUT) systems, ensuring that the qualification and project specific validation of any AUT system is according to the requirements of OS-F101 Appendix E and is consistently performed to comply with the specific requirements of the referenced code. In principle, the guideline can be utilised for all materials but special care shall be taken for applications where inconsistent wave propagation or other wave physics are affected by structural properties.