Académique Documents
Professionnel Documents
Culture Documents
com community You are free to distribute this file to other persons who needs it , but without of charge Also on http://electromaniacs.com you can find thousands of service manuals , schematics free of charge
SAFETY PRECAUTIONS
IMPORT ANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitary that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this monitor is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts. Due to high vacuum and large surface area of picture tube, extreme care should be used in handling the Picture Tube. Do not lift the Picture tube by it's Neck.
AC Volt-meter
1.5 Kohm/10W
CANADA: LG Electronics Canada, Inc. 550 Matheson Boulevard East Mississauga, Ontario L4Z 4G3 USA : LG Customer Interactive Center P.O.Box 240007, 201 James Record Road Huntsville, AL 35824 Digital TV Hotline 1-800-243-0000
- 2 -
TABLE OF CONTENTS
DESCRIPTION OF CONTROLS ...........................................4 SPECIFICATIONS.................................................................7 ADJUSTMENT INSTRUCTIONS ..........................................8 TROUBLE SHOOTING GUIDE ...........................................12 BLOCK DIAGRAM...............................................................23 EXPLODED VIEW...............................................................26 EXPLODED VIEW PARTS LIST .........................................27 REPLACEMENT PARTS LIST ............................................28 SCHEMATIC DIAGRAM.......................................................... PRINTED CIRCUIT BOARD ...................................................
- 3 -
DESCRIPTION OF CONTROLS
Controls
- This is a simplified representation of front panel. Here shown may be somewhat different from your TV. - This manual explains the features available on the RU-42PX10 TVs.
ON/OFF
TV/VIDEO
MENU
VOL
CH
CHANNEL (E,
D)
Buttons
Power Standby Indicator Illuminates red in standby mode, Illuminates green when the TV is turned on.
- 4 -
DESCRIPTION OF CONTROLS
Connection Options
S-VIDEO Input A connection available to provide better picture quality than the video input.
S-VIDEO
L / MONO
VIDEO Input Connects the video signal from a video device. AUDIO Input Use to connect to hear stereo sound from an external device.
VIDEO
R AUDIO
DVD/DTV Input (Component 1-2) Connect a component video/audio device to these jacks. Remote Control Port Connect your wired remote control here.
Monitor Output Connect a second TV or Monitor. S-Video Input Connect S-Video out from an S-VIDEO device to the S-VIDEO input.
A/V INPUT2
REMOTE CONTROL
RS-232C INPUT
(CONTROL/SERVICE)
S-VIDEO
Antenna
AC INPUT
DVI INPUT
AUDIO INPUT
AUDIO
AUDIO
VIDEO
Audio/Video Input 1 Connect audio/video output from an external device to these jacks. RGB Input/Audio Input/DVI Input Connect the monitor output connector from a PC to the appropriate input port. RS-232C INPUT (CONTROL/SERVICE) PORT Connect to the RS-232C port on a PC.
Antenna Input Connect cable or antenna signals to the TV, either directly or through your cable box.
Power Cord Socket This TV operates on AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
- 5 -
DESCRIPTION OF CONTROLS
MUTE Switches the sound on or off. TVVIDEO Selects: TV, Video 1-2, Component 1-2, RGB, and DVI input sources. MULTIMEDIA Selects: Component 1-2, RGB, and DVI input sources. CAPTION Selects CAPTION mode.
MUTE
POWER
POWER Turns your TV on or off. MTS Selects the MTS sound: Mono, Stereo, or SAP. MENU Brings up the main menu to the screen. ARC Changes the picture format.
CAPTION ARC
MENU
CH
ENTER
VOL VOL CH
VOLUME UP/DOWN Increases/decreases the sound level. CHANNEL UP/DOWN Selects available channels found with Auto program. ENTER Accepts your selection or displays the current mode. FCR Use to scroll the favorite channel list. APC Adjusts the factory preset picture according to the room. PIP/DW Switches between PIP and Twin picture modes. SPLIT ZOOM Enlarges the picture with regular ration. WIN. SIZE Adjusts the sub picture size. POSITION Moves the sub picture in pip mode. SWAP Exchanges the main/sub images.
1 4 7
FCR
2 5 8 0
3 6 9
REVIEW
NUMBER buttons
REVIEW Tunes to the last channel viewed. DASP Selects the sound appropriate for the program's character. SLEEP Sets the sleep timer. PIPCH-/PIPCH+ Changes to next lower/higher PIP channel. PIP INPUT Selects the input source for the sub picture. A.PROG (AUTO PROGRAM) Searches for available channels. MEMORY/ERASE Memorizes or erases selected channel.
APC PIP/DW
DASP
SPLIT ZOOM PIP CH + SLEEP WIN.SIZE PIP CH - PIP INPUT POSITION SWAP A.PROG MEMORY/ERASE
- 6 -
SPECIFICATIONS
MODELS
Width (inches / mm) Height (inches / mm) Depth (inches / mm) Weight (pounds / kg) Resolution Power requirement Television System Program Coverage External Antenna Impedance Color Operating Temperature Range Operating Humidity Range Maximum Elevation
RU-42PX10/20
48.4 / 1210 27.6 / 701 11.4 / 290 66 / 22.9 852 x 480 (Dot) AC100-240V, 50/60Hz NTSC
RU-50PX10/20
56 / 1400 30.4 / 761.5 11.4 / 290 66 / 29.9 1366 x 768 (Dot)
VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125 75 16,770,000 (256 steps of each R, G and B) 32 ~ 104F (0 ~ 40C) Less than 80% 6561 feet (2000m)
The specifications shown above may be changed without notice for quality improvement.
- 7 -
ADJUSTMENT INSTRUCTIONS
1. Application Object
These instructions apply to the RF-043A Chassis. (2) After installing the Gprobe, [Option -> Connection Setup] or click the icon indicated in the picture and then setup as below the picture. (In case of the port (second one), set to the serial port of the connected PC. The other only have to be set as below the picture.) (3) After finishing inputs, click the button [OK] to complete the connection setup.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of 255C of temperature and 6510% of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep 100~220V, 50/60Hz. (5) The receiver must be operated for about 15 minutes prior to the adjustment. After RGB Full white HEAT-RUN Mode, the receiver must be operated prior to adjustment. O Enter into HEAT-RUN MODE 1) Press the POWER ON KEY on R/C for adjustment. 2) OSD display and screen display 100% full WHITE PATTERN.
O
[ Set is activated HEAT-RUN without signal generator in this mode. [ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL. Caution) If you turn on a still screen more than 20 minutes (Especially digital pattern, cross hatch pattern), a after image may be occur in the black level part of the screen.
3. Channel memory
3-1. Setting up the G-prove
(Fig 2)
- 8 -
ADJUSTMENT INSTRUCTIONS
Each PCB assembly must be checked by check JIG set. (Because power PCB Assembly damages to PDP Module, especially be careful)
4. HDCP download
4-1. Setting up & Confirming the G-prove
: Refer to 3-1 and 3-2.
(Fig 4)
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P805, connect terminal to GND pin of P805.
- 9 -
ADJUSTMENT INSTRUCTIONS
2) After turning RV401, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V) (2) Supply Gray Pattern (216 Level Full Size Pattern) signal to VIDEO input. (AV2 Input 60Hz) (Refer to Fig. 6) (3) To adjust, stick sensor to 216 Gray Level Pattern, press ADJ key twice(White Balance) on remote control. For adjustment and D, E on reomte control for adjustment mode to select Red Gain and Blue Gain, press VOL +, Key and adjust it until color coordination becomes as below. X; 0.2830.003, Y; 0.2970.003 Color Temperature; 9,300K500K
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P805, connect terminal to GND pin of P805. 2) After turning RV401, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V)
Window
MSPG-2100 or MSTG-5200
(1) Input RGB Source : Component 480p/576p 16 Gray Scale Pattern At this time, except Pb and Pr signal, only Y signal insert. (2) Press ADJ KEY on R/C for adjustment. (3) Press Vol. + KEY and operate To set. (4) Auto-RGB OK means completed adjustment.
Operate the Zero-calibration of the CA-100, then stick sensor to PDP module surface when you adjust. For manual adjustment, it is also possible by the following sequence.
(1) Select white pattern of heat-run mode by pressing power on key on remote control for adjustment then operate heat run more than 15 minutes. (Fig 7) Auto RGB/ Component Color Balance Test Pattern
- 10 -
ADJUSTMENT INSTRUCTIONS
9. Auto Adjustment Map(RS-232C)
RF-043A Type Baud Rate 115200 Data bit 8 RS232 Stop bit 1 Parity NONE 6) If Check Sum is not 53, repeat 3) ~ 4). 7) If Check Sum is 53, DDC data for Analog-RGB input is completed.
Index Cmd1 Cmd2 Data Min Value Max Value R Gain G Gain Protocol B Gain Setting R Offset G Offset B Offset j j j j j j a b c d e f 00(00) 00(00) 00(00) 00(00) 00(00) 00(00) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF)
- 11 -
Start check
Yes
No
No
Yes
No
Doesn't the 5V Monitor signal come out? Yes 4. Check the 5V Monitor signal circuit.
No
Doesn't the VSC signal RL-ON come out? Yes 5. Check the VSC RL-ON signal.
No
Yes
No
Doesn't the Vs, Va voltage output come out? Yes 8. Check the Vs, Va voltage output circuit.
Doesn't the VSC low pressure output come out? Yes 6. Check the VSC low pressure output
No
No
Yes
When remove the Y, Z B/D Module Input Connector, Power Board high tension output voltage Drop it occurs? Yes 9. Check the Power Board Output high tension circuit
No
When remove the Y B/D Module Input Connector, output voltage Drop it occurs? Yes 10. Check the Z B/D Module Coutput circuit
No
When remove the Z B/D Module Input Connector, output voltage Drop it occurs? Yes 11. Check the Y B/D Module Coutput circuit
No
- 12 -
- 13 -
- 14 -
Doest minute discharge at module. Non does not come in into the front LED.
No Connect Cable.
No Replace Fuse.
No Connect Cable.
No Connect Cable.
After remove the cable connect to Power Board(except the CN101 connection cable), authorizes the AC voltage marking on manual. When ST-BY 5V does not operate, replace Power Board.
- 15 -
- 16 -
Doest minute discharge at module. It maintains the condition where the front LED is green.
- 17 -
LED is green The minute discharge continuously becomes accomplished from module
Yes
No
Yes
Yes
Yes
Replace IEP(IC500).
Replace Scaler(IC700).
- 18 -
The screen does not become the display from specific input mode (RF, AV, Component, RGB, DVI).
Check the all input mode should become normality display. Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode. (Re-Check it Swap)
No
No Replace IC
- 19 -
(6) In the case of becomes unusual display from Component DTV mode
Is normal the 74LS123? Yes Is normal the CXA2101? Yes Is normal the M52758? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC
- 20 -
- 21 -
No
Yes
- 22 -
WIRE IR
RS232_RX/ TX Co mp _480I/ P RGB PC RGB_Dat a ADC w/ PLL
TX IR TX_Out
74ACT253
Co mp / RGB_SW
RS232
ZHINE
RGB DTV Comp DTV CXA_RGB
RX0/1,TX0/1
RGB (PC/DTV)
CXA2101 IEP
DVI RX w/ HDCP 10
RGB H/ V
74HCT08
24LC21
DVI (PC/DTV)
TX0/ 1/ 2/ 3/ C Disp _En SDATA SCLK, SLE
RX/ TX0/ 1/ 2,
RX/ TXC
SCL/ SDA
24LC21
Dig it al BOARD
Main_V Main_YC
Scart 1
VPC3230 (M ) Video Decoder
YCb Cr S2300 / DeInt erlac er 8
1H RGB
Vin2 ( CVBS )
BLOCK DIAGRAM
- 23 Main_V
Scart 2
HY57V64322 SDRAM ( 8MB)
MNT OUT
Scart 3
CXA2069Q SWITCH
Main_YC
Vin3 (CVBS )
RF
Tuner (M)
TU_Main
Tuner ( S )
Text _V
TU_Sub
CVBS
SDA6001 Text Processor
Vin4
S-VHS
YCin4
AM29LV160 F-ROM
Po s-t p ro c es sing Blo c k is o m it t ed . so alled JEPICO, in this c ase -c TMDS TX is also req uired . So und Pro c es sing Blo c k Diag ram is sep arat ed . . RCA yp e Blo c k Diag ram is also -t sep arat ed . .
Comp1 (DVD/DTV )
Co mp _Y
HYV641620 SRAM
74LS123
Analo g BOARD
CVBS S-VHS
Co mp _480I/ P To Malib u
Sid e - AV BOARD
Di gt a l BOARD IEP
WIRE IR
TMDS Transf er / Thine Analo g RGB DVI g m1501H TQFP 128K DDR Memo ry
Tx
74ACT253
RS232
IIS
ST3232C
74HCT08
ZHINE
IIS
24LC21
RGB DTV CXA2101 RGB_DTV VPORT ( 24b it) SVPORT ( 16b it) Flash ROM 512K/ 1M
IIS
24LC21
LVDS 31PIN
M52758FP IC204 DAC_RGB DTV2_Co mp DTV_Co mp M37136 ( OTP) DVD_MAIN M52758FP IC400( MUX) ALT_Y_480I_MAIN ALT_Y2_480I_MAIN MAIN_YOUT CAB_VIN COMB_YOUT MAIN_COUT UPD64083 COMB_COUT VPC3230 ( MAIN) M656 8 Bit S/ DVD_Co mp CAB_Co mb FLI2300 RGB_24Bit
Analo g BOARD
Co m p 1
DVD2_MAIN
Co mp
BLOCK DIAGRAM
- 24 MAIN_VOUT MAIN_YOUT LA7151M SW CVBS/ Y ALT_Y_480I_SUB ALT_Y2_480I_SUB DVD_SUB DVD2_SUB SUB_YOUT SUB_COUT VPC3230 ( SUB) S656 8 Bit
( DVD/ DT V)
Co mp 2
Co m p 2
( DVD/ DTV)
CVBS IN
VIN1
CVBS OUT
MNT_OUT
S-VHS
Y/ CIN1
RF
Tuner ( M)
CXA2069Q
Tuner ( S)
Sid e A/ V
Side-CVBS
VIN2
Sid e S-VHS
Y/ CIN2
NOTES
- 25 -
EXPLODED VIEW
300 121
600 305
601 301
304 120
303 302
200
205
580
401
430
- 26 -
- 27 -
LOCA. NO
PART NO
DESCRIPTION
DESCRIPTION MSP4440G QA C13 101 MX29LV800TTC 70 48PIN 8MBIT, 3.3V NSP 6241B 64P DIGITAL AUDIO TAS5122DCAR 56P/TSSOP R/TP 30W KIA7042AF SOT 89 TP 4.2V
IC
IC100 IC100 IC1000 IC1001 IC1002 IC1003 IC1004 IC101 IC102 IC103 IC104 IC1100 IC1100 IC1101 IC1200 IC1201 IC1202 IC1300 IC1301 IC1302 IC1303 IC1304 IC1305 IC1306 IC200 IC201 IC202 IC203 IC204 IC400 IC401 IC500 IC500 IC501 IC502 IC503 IC600 IC600 IC601 IC601 IC602 IC700 IC700 IC701 IC702 IC800 0IMMRAL014B 0IMI623200B 0IMCRFA010A 0IPRPML001A 0IMCRSH001A 0ITK118100B 0IMCRSH001A 0IMMRAL014B 0IMCRTI003A 0IMCRTI021A 0IMCRTI021A 0IMCRTH002A 0IMMRNE002A 0ISA715100D 0IMCRSJ001A 0IPRPML001A 0IMCRFA010A 0IMCRRH001A 0IMCRSH001A 0IMCRSH001A 0IMCRRH001A 0IMCRSJ001A 0IMCRRH001A 0IPRPML001A 0IFA742530B 0IMCRSG010A 0IMCRMI006A 0IFA741230A 0IFA741230A 0ISO206900A 0ISO210100B 0ICTMLG018A 0IZZVC0121A 0IMCRTI003A 0IMCRAL006A 0IKE703300E 0IMCRGN002C 0IMCRMI006A 0IMMRHY033A 0IIT323000E 0ISA715100D 0IPRPGN012A 0IIT323000E 0IMMRAL025A 0IKE704200J 0IMMRHY020B AT24C02N 10SI 2.7 8P M62320FP 16P KA7809R 2P MIC39100 3P SOT223 PQ05DZ1U SHARP 5 TK11840L 8P SOT23L DC DC CONVERTER PQ05DZ1U SHARP 5 AT24C02N 10SI 2.7 8P SN74HCT08D 16P SN74LVTH541PWR 20P SN74LVTH541PWR 20P THC63LVD103 64P 10BIT UPD64083GF3BA 100 3D YC LSI LA7151M 10SOP R/TP AUDIO SW SC1565IST 1.8 3P SOT223 MIC39100 3P SOT223 KA7809R 2P BA033FP E2 3P SOP,TO252 3 PQ05DZ1U SHARP 5 PQ05DZ1U SHARP 5 BA033FP E2 3P SOP,TO252 3 SC1565IST 1.8 3P SOT223 BA033FP E2 3P SOP,TO252 3 MIC39100 3P SOT223 74ACT253SC 16P ST3232CDR SOP16 RS232 M52758FP 36PIN DM74LS123MX 16SOP DM74LS123MX 16SOP CXA2069Q QFP64 BK I2C BUS AV S/W CXA2101AQ 80P VIDEO SIGNAL LGDT4410 LG IC 176P QFP TRAY IEP M37136EFSP DIP 52P BK RF 043A SN74HCT08D 16P AT24C16AN 10SI 2.7 8P KIA7033AF 3P SOT 89 FLI2300BD 208P DIGITAL VIDEO M52758FP 36PIN, R/TP PLL IC HY57V643220C(L)T 6 86P 64M VPC3230D C5 80P VIDEO LA7151M 10SOP R/TP AUDIO SW GM1501HBD 416P VPC3230D C5 80P VIDEO AT24C32AN 10SI 2.7 8PIN KIA7042AF SOT 89 TP 4.2V HY5DU283222AQ 5 100P
TRANSISTOR
Q001 Q002 Q100 Q100 Q1000 Q101 Q101 Q102 Q102 Q103 Q103 Q104 Q105 Q106 Q107 Q108 Q110 Q1100 Q1101 Q1102 Q1103 Q1104 Q1105 Q1106 Q1107 Q1108 Q1109 Q111 Q1110 Q1111 Q1112 Q1113 Q1114 Q1115 Q1116 Q1117 Q1118 Q1119 Q112 Q113 Q1200 0TR387500AA 0TR387500AA 0TR830009BA 0TR150400BA 0TRKE80038A 0TR830009BA 0TR387500AA 0TR830009BA 0TR387500AA 0TR830009BA 0TR150400BA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR830009BA 0TR387500AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR150400BA 0TR150400BA 0TR387500AA 0TR387500AA 0TR150400BA 0TR150400BA 0TR830009BA 0TR150400BA 0TR150400BA 0TR150400BA 0TR387500AA 0TR387500AA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR102009AG 0TR830009BA 0TR830009BA 0TR387500AA CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC BSS83 CHIP 2SA1504S(ASY) KEC KTC3552T RTK SOT 23F 50V 3A BSS83 CHIP 2SC3875S(ALY) KEC BSS83 CHIP 2SC3875S(ALY) KEC BSS83 CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC BSS83 CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC BSS83 CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP KRC102S SOT 23 BSS83 BSS83 CHIP 2SC3875S(ALY) KEC
- 28 -
DIODE
CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 KDS184S CHIP 85V 300MA CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 KDS184S CHIP 85V 300MA CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23 CHIP KDS226 SOT 23
- 29 -
CAPACITOR
C002 C1001 C1002 C1003 C1004 C1006 C1016 C1017 C1018 C102 C102 C1020 C1022 C1025 C1027 C1031 C1037 C104 C1041 C1042 C1045 C1046 C105 C1052 0CE4763F618 0CE107SF6DC 0CE227VF6DC 0CE107SF6DC 0CE475SK6DC 0CE477SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE474SK6DC 0CE475SK6DC 0CE107SF6DC 0CE477SF6DC 0CE475SK6DC 0CE107SF6DC 0CE477SF6DC 0CE477SF6DC 0CE476DF618 0CE107SF6DC 0CE477SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476DF618 0CE107SF6DC 47UF SRE 16V M 100UF MVG 16V M 220UF MV 16V 20% 100UF MVG 16V M 4.7UF MVG 50V 20% 470UF MVG 16V 20% 100UF MVG 16V M 100UF MVG 16V M 100UF MVG 16V M 0.47UF MVG 50V M 4.7UF MVG 50V 20% 100UF MVG 16V M 470UF MVG 16V 20% 4.7UF MVG 50V 20% 100UF MVG 16V M 470UF MVG 16V 20% 470UF MVG 16V 20% 47UF STD 16V M 100UF MVG 16V M 470UF MVG 16V 20% 100UF MVG 16V M 100UF MVG 16V M 47UF STD 16V M 100UF MVG 16V M
- 30 -
- 31 -
JACK
JACK ASSEMBLY,UJB 03 28A JACK,RCA PPJ122B 6P JACK,RCA PPJ122C 6P JACK,RCA PPJ121B 4P JACK,PHONE UEJ CV 018 JACK,DIN 440062 JACK,DIN 6046B 01S JACK,PHONE UEJ CV 018
COIL
COIL,CHOKE 26UH
- 32 -
RESISTOR
AR1101 AR1102 AR1103 AR1104 AR1105 AR1106 AR500 AR503 AR507 AR508 AR509 AR512 AR513 AR520 AR521 AR522 AR523 AR524 AR525 AR600 AR600 AR601 AR601 AR602 AR602 AR603 AR603 AR604 AR605 AR606 AR607 AR608 AR609 AR610 AR611 AR612 AR613 AR614 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5% 22 OHM 1 / 16 W 1608 5%
SWITCH
SW001 SW002 SW003 SW004 SW005 SW006 SW700 SW800 SW800 140-315A 140-315A 140-315A 140-315A 140-315A 140-315A 140-313B 6600VM2006A 140-275A SWITCH,TACT SKHV17910B 12V SWITCH,TACT SKHV17910B 12V SWITCH,TACT SKHV17910B 12V SWITCH,TACT SKHV17910B 12V SWITCH,TACT SKHV17910B 12V SWITCH,TACT SKHV17910B 12V SWITCH,TACT 2LEAD 160G(TA) SWITCH,PUSH SDDF3PATP011 SWITCH,PUSH JDPB21SA 30V 0.3A
- 33 -
- 34 -
CONNECTOR
C10 C11 C12 C13 C14 C15 C4 C5 C6 C7 C8 C9 P100 P200 6631V25083C 6631V25084C 6631V39013Z 6631V39022D 6631V39023C 6631Q20003C 6631V10008A 6631V39021H 6631V00020F 387-J12M 387-J10K 6631V00045G 6630VGA001C 6630VGA004B CONNECTOR ASSEMBLY,7P 2.5MM 200MM CONNECTOR ASSEMBLY,12P 2.5MM 200MM CONNECTOR ASSEMBLY,8P 3.96MM 650MM CONNECTOR ASSEMBLY,4P 3.96MM 250MM CONNECTOR ASSEMBLY,10P 3.96MM 200MM CONNECTOR ASSEMBLY,2.0MM 8PIN 100MM CONNECTOR ASSEMBLY,31P 1.0MM 50MM CONNECTOR ASSEMBLY,4P 3.96MM 450MM CONNECTOR ASSEMBLY,3P 3.96MM 250MM CONNECTOR ASSEMBLY,12P 2.5MM 800MM CONNECTOR ASSEMBLY,10P 2.5MM 600MM CONNECTOR ASSEMBLY,10P 2.5MM 400MM CONNECTOR,D-SUB 15PIN 2.29MM CONNECTOR,D-SUB 9P 2.77MM
MISCELLANEOUS
C1 C2 F801 F801A F802A IC801 PA001 TU100 TU101 6850VA0004H 6851V00022C 0FS1002B53K 430-813A 430-813A 6927V1063AU 6712000002B 6700NF0010A 6700NF0010B CABLE,COAXIAL(NTSC PLUG) UL1365AWG26 CABLE,COAXIAL(150MM),UL1365#26 VW-1 FUSE,SLOW BLOW 10000MA 250V HOLDER,FUSE NON MC994C PAPING HOLDER,FUSE NON MC994C PAPING SOFT WARE,3.27V 83A0 PDP RF043A REMOTE CONTROLLER RECEIVER,38KHZ TUNER,TAUM H501P TUNER,TAFM H502P
ACCESSORIES
A1 A2 A3 A4 A5 A6 A7 3828VA0470D 3828VA0470A 6710V00126S 6710V00137G 6410VUH005A 6410VEH003C 6850J00002B 6850J00004A 6866VA9001B 4810V00509A 4972V00178A MANUAL,OWNERS RF043A MANUAL,OWNERS *LGEUS REMOTE CONTROLLER,RF043A PIP REMOTE CONTROLLER POWER CORD,PS204 125V/13A 2800MM POWER CORD CABLE,DVI D TO DVI D UL20276 CABLE,DVI LVDS UL20276 AWG30 500MM CONNECTOR ,D SUB 2990 9C UL 1161 BRACKET,WALL FIXER,WALL
- 35 -
P/NO : 3828VD0179D
CANADA: LG Electronics Canada, Inc. 550 Matheson Boulevard East Mississauga, Ontario L4Z 4G3 USA : LG Electronics Alabama, Inc. P.O.Box 240007, 201 James Record Road Bldg 3 Huntsville, AL 35824
MAIN (TOP)
TUNER(TOP)
TUNER(BOTTOM)
POWER S/W(TOP)
POWER S/W(BOTTOM)
SIDE A/V(TOP)
SIDE A/V(BOTTOM)
CONTROL(TOP)
CONTROL(BOTTOM)