Académique Documents
Professionnel Documents
Culture Documents
1. General description
The TDA8947J contains four identical audio power ampliers. The TDA8947J can be used as: four Single-Ended (SE) channels with a xed gain of 26 dB, two times Bridge-Tied Load (BTL) channels with a xed gain of 32 dB or two times SE channels (26 dB gain) plus one BTL channel (32 dB gain) operating as a 2.1 system The TDA8947J comes in a 17-pin Dil-Bent-Sil (DBS) power package. The TDA8947J is pin compatible with the TDA8944AJ and TDA8946AJ. The TDA8947J contains a unique protection circuit that is solely based on multiple temperature measurements inside the chip. This gives maximum output power for all supply voltages and load conditions with no unnecessary audio holes. Almost any supply voltage and load impedance combination can be made as long as thermal boundary conditions (number of channels used, external heatsink and ambient temperature) allow it.
2. Features
s s s s s s s s s SE: 1 W to 25 W, BTL: 4 W to 50 W operation possibility (2.1 system) Soft clipping Standby and Mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Pin compatible with TDA8944AJ and TDA8946AJ
3. Applications
s s s s Television PC speakers Boom box Mini and micro audio receivers
Philips Semiconductors
TDA8947J
4-channel audio amplier
Min 9 -
Typ 18 100 -
Max 26 28 145 10
Unit V V mA A
[1]
The amplier can deliver output power with non clipping output signals into nominal loads as long as the ratings of the IC are not exceeded.
5. Ordering information
Table 2: Ordering information Package Name TDA8947J DBS17P Description plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm) Version SOT243-1 Type number
2 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
6. Block diagram
VCC1 3 IN1+ 8
60 k
VCC2 16 1 OUT1+
IN2+
6
60 k
OUT2
IN3+
9
60 k
14
OUT3
IN4+
12
60 k
17
OUT4+
CIV
13 VCC
SVR
11
0.5VCC Vref
SGND
MODE1
10
TDA8947J
MODE2
3 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
7. Pinning information
7.1 Pinning
1 2 3 4 5 6 7 8 9
TDA8947J
4 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
Pin description continued Pin 16 17 Description supply voltage channels 3 and 4 non inverted loudspeaker output of channel 4 back side tab or heat spreader has to be connected to ground
8. Functional description
8.1 Input conguration
The input cut-off frequency is: 1 f i ( cut off ) = ---------------------------2 ( R i C i ) For SE application Ri = 60 k and Ci = 220 nF: 1 f i ( cut off ) = ---------------------------------------------------------------- = 12 Hz 3 9 2 ( 60 10 220 10 ) For BTL application Ri = 30 k and Ci = 470 nF: 1 f i ( cut off ) = ---------------------------------------------------------------- = 11 Hz 3 9 2 ( 30 10 470 10 ) (3) (2) (1)
As shown in Equation 2 and Equation 3, large capacitor values for the inputs are not necessary, so the switch-on delay during charging of the input capacitors can be minimized. This results in a good low frequency response and good switch-on behavior.
Low peak value of the supply current Ripple frequency on the supply voltage is twice the signal frequency No expensive DC-blocking capacitor Good low frequency performance
5 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
SE: RL = 3 BTL: RL = 6
8.2.2 Headroom
Typical CD music requires at least 12 dB (factor 15.85) dynamic headroom, compared to the average power output, for transferring the loudest parts without distortion. The Average Listening Level (ALL) music power, without any distortion, yields:
(4)
(5)
The power dissipation can be derived from Figure 9 (SE and BTL) for a headroom of 0 dB and 12 dB, respectively.
Table 4: Headroom 0 dB 12 dB Power rating as function of headroom Power output SE Po = 5 W Po(ALL) = 315 mW BTL Po = 10 W Po(ALL) = 630 mW Power dissipation (all channels driven) PD = 17 W PD = 9 W
For heatsink calculation at the average listening level, a power dissipation of 9 W can be used.
6 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
On The amplier is operating normally. The On mode is activated at VMODE1 > (VCC 2.0 V). The output of channels 3 and 4 can be set to Mute or On mode. The output channels 3 and 4 can be switched on/off by applying a proper DC voltage to pin MODE2, under the condition that the output channels 1 and 2 are in the On mode (see Figure 3).
Table 5: MODE1 0 V to 0.8 V 4.5 V to (VCC 3.5 V) (VCC 2.0 V) to VCC Mode selection Channel 1 and 2 MODE2 0 V to VCC 0 V to VCC 0 V to (VCC 3.5 V) (VCC 2 V) to VCC Standby mode Mute mode On mode On mode Channel 3 and 4 (sub woofer) Standby mode Mute mode Mute mode On mode
Voltage on pin
all standby
all mute
0.8
4.5
VCC 3.5
channels 3 + 4: mute
channels 3 + 4: on
VCC 3.5
mdb016
VCC 2.0
VCC VMODE2
7 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
9. Limiting values
Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VCC VI IORM Tstg Tamb Ptot VCC(sc)
[1]
Parameter supply voltage input voltage repetitive peak output current storage temperature ambient temperature total power dissipation supply voltage to guarantee short-circuit protection
Unit V V V A C C W V
non-operating
55 40 -
The amplier can deliver output power with non clipping output signals into nominal loads as long as the ratings of the IC are not exceeded.
8 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
Min 9 -
Typ 18 100 9 -
Unit V V mA A V mV V V V A A
VCC 3.5 V
VCC 2.0 0 -
VCC 3.5 V
selection current on pin MODE1 0 V < VMODE1 < (VCC 3.5 V) selection current on pin MODE2 0 V < VMODE2 < (VCC 3.5 V)
A minimum load is required at supply voltages of VCC > 22 V: RL = 3 for SE and RL = 6 for BTL. The amplier can deliver output power with non clipping output signals into nominal loads as long as the ratings of the IC are not exceeded. With a load connected at the outputs the quiescent current will increase. The DC output voltage, with respect to ground, is approximately 0.5VCC. VOUT = |VOUT+ VOUT-| Channels 3 and 4 can only be set to Mute or On mode by MODE2 when VMODE1 > VCC 2.0 V.
Min 7 25 40
Max 0.5 27 -
Unit W W W % dB k
Po = 1 W
9 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
Table 9: Dynamic characteristics SE continued VCC = 18 V; Tamb = 25 C; RL = 4 ; f = 1 kHz; VMODE1 = VCC; VMODE2 = VCC; measured in test circuit Figure 12; unless otherwise specied. Symbol Vn(o) SVRR Vo(mute) cs |Gv|
[1] [2]
Parameter noise output voltage supply voltage ripple rejection output voltage in Mute mode channel separation channel unbalance
Conditions
[1]
Typ 150 60 60 60 -
Max 150 1
Unit V dB dB V dB dB
The noise output voltage is measured at the output in a frequency range from 20 Hz to 22 kHz (unweighted), with a source impedance Rsource = 0 at the input. Supply voltage ripple rejection is measured at the output, with a source impedance Rsource = 0 at the input and with a frequency range from 20 Hz to 22 kHz (unweighted). The ripple voltage is a sine wave with a frequency fripple and an amplitude of 300 mV (RMS), which is applied to the positive supply rail. Output voltage in Mute mode is measured with VMODE1 = VMODE2 = 7 V, and Vi = 1 V (RMS) in a bandwidth from 20 Hz to 22 kHz, including noise.
[3]
Table 10: Dynamic characteristics BTL VCC = 18 V; Tamb = 25 C; RL = 8 ; f = 1 kHz; VMODE1 = VCC; VMODE2 = VCC; measured in test circuit Figure 12; unless otherwise specied. Symbol Po(BTL) Parameter BTL output power Conditions VCC = 18 V; see Figure 8b THD = 10 %; RL = 8 THD = 0.5 %; RL = 8 VCC = 22 V THD = 10 %; RL = 8 THD Gv Zi Vn(o) SVRR Vo(mute) cs |Gv|
[1] [2]
Min 16 31 20
[1]
Unit W W W % dB k V dB dB V dB dB
total harmonic distortion voltage gain input impedance noise output voltage supply voltage ripple rejection output voltage in Mute mode channel separation channel unbalance
Po = 1 W
50 -
The noise output voltage is measured at the output in a frequency range from 20 Hz to 22 kHz (unweighted), with a source impedance Rsource = 0 at the input. Supply voltage ripple rejection is measured at the output, with a source impedance Rsource = 0 at the input and with a frequency range from 20 Hz to 22 kHz (unweighted). The ripple voltage is a sine wave with a frequency fripple and an amplitude of 300 mV (RMS), which is applied to the positive supply rail. Output voltage in Mute mode is measured with VMODE1 = VMODE2 = 7 V, and Vi = 1 V (RMS) in a bandwidth from 20 Hz to 22 kHz, including noise.
[3]
10 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
coc005
12
16 20 VMODE1 (V)
60 Po (W) 40
mce485
60 Po (W) 4 40 8 6
mce484
2 20 RL = 1
3
20 RL = 2 16
4 8
0 8 12 16 20 24 VCC (V) 28
0 8 12 16 20 24 28 VCC (V)
a. SE
b. BTL
11 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
mce488
mce487
101
101
102 101
10
Po (W)
102
102 101
10
Po (W)
102
VCC = 18 V; f = 1 kHz; RL = 4 .
VCC = 18 V; f = 1 kHz; RL = 8 .
a. SE
b. BTL
10 THD + N (%) 1
mce489
10 THD + N (%) 1
mce490
101
101
102 10
102
103
104
f (Hz)
105
102 10
102
103
104
f (Hz)
105
VCC = 18 V; Po = 1 W; RL = 4 .
VCC = 18 V; Po = 1 W; RL = 8 .
a. SE
b. BTL
12 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
50 Po (W) 40
mce491
50 Po (W) 40
mce492
30
30
20
20
10
10
0 8 12 16 20 24 28 VCC (V)
0 8 12 16 20 24 28 VCC (V)
THD = 10 %; RL = 4 ; f = 1 kHz.
THD = 10 %; RL = 8 ; f = 1 kHz.
b. BTL
20 PD (W) 16
mce493
20 PD (W) 16
mce494
12
12
0 0 4 8 12 16 Po (W) 20
0 0 4 8 12 16 Po (W) 20
VCC = 18 V; RL = 4 .
VCC = 18 V; RL = 8 .
a. SE
b. BTL
Fig 9. Total power dissipation as function of channel output power per channel (worst case, all channels driven)
13 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
0 cs (dB) 20
mce495
0 cs (dB) 20
mce496
40
40
60
60
80
80
100 10
102
103
104 f (Hz)
105
100 10
102
103
104 f (Hz)
105
VCC = 18 V; RL = 4 .
VCC = 18 V; RL = 8 .
a. SE
b. BTL
Fig 10. Channel separation as function of frequency (no bandpass lter applied)
0 SVRR (dB) 20
mce497
0 SVRR (dB) 20
mce498
40
40
60
60
80 10
102
103
104
f (Hz)
105
80 10
102
103
104
f (Hz)
105
VCC = 18 V; Rsource = 0 ; Vripple = 300 mV (RMS). A bandpass lter of 20 Hz to 22 kHz has been applied. Inputs short-circuited.
VCC = 18 V; Rsource = 0 ; Vripple = 300 mV (RMS). A bandpass lter of 20 Hz to 22 kHz has been applied. Inputs short-circuited.
a. SE
b. BTL
14 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
RL 4
270
BC547
2.2 F
MODE1 10
VCC
MODE2 5
TDA8947J
2 GND1 15 GND2
mdb017
Fig 12. Typical application diagram without on/off switching plops Table 11: Amplier selection by microcontroller Microcontroller with open-collector output; see Figure 12. Microcontroller LOW HIGH Channels 1 and 2 On mode Mute mode Channels 3 and 4 On mode Mute mode
15 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
VCC VCC1 3
220 nF
VCC2 16
100 nF
1000 F
IN1+ 8
60 k
1 OUT1+ +
RL 4
Vi
220 nF
IN2+ 6
60 k
4 OUT2 + 14 OUT3
60 k RL 4
Vi IN3+ 9
470 nF
+ 17 OUT4+
450 F RL 8
Vi
IN4+ 12
60 k
CIV 13 VCC
22 F SVR 11 0.5V CC
150 F
Vref
MICROCONTROLLER VCC
MODE1 10
TDA8947J
MODE2 5
Fig 13. Application diagram with one pin control and reduction of capacitor
Remark: Because of switching inductive loads, the output voltage can rise beyond the maximum supply voltage of 28 V. At high supply voltages, it is recommended to use (Schottky) diodes to the supply voltage and ground.
16 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
TVA
220 nF
4
4
1 1
220 nF 220 nF
BTL1/2
1000 F
4
1000 F
4.7 nF
SVF
22 220 F F
+SE3
+SE2 +SE1
9397 750 14938
1000 F
1000 F
SE4+
150 F
MODE1
BTL3/4 MODE2
OFF 10 k SB ON MUTE ON
mce483
17 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
18 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
150 Tj (C)
(1) (2) (3) (4)
mce499
150 Tj (C)
mce500
(5)
(1)
(2)
(3)
(4)
(5)
100
100
50
50
0 8 12 16 20 24 28 VCC (V)
0 8 12 16 20 24 28 VCC (V)
Fig 15. Junction temperature as function of supply voltage for various loads with music signals
19 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
non-concave D x Dh
Eh
B j E A
L3
Q c v M
1 Z e e1 w M
17 m e2
bp
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 17.0 15.5 A2 4.6 4.4 bp 0.75 0.60 c 0.48 0.38 D (1) 24.0 23.6 d 20.0 19.6 Dh 10 E (1) 12.2 11.8 e e1 e2 5.08 Eh 6 j 3.4 3.1 L 12.4 11.0 L3 2.4 1.6 m 4.3 Q 2.1 1.8 v 0.8 w 0.4 x 0.03 Z (1) 2.00 1.45
2.54 1.27
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT243-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION
20 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
16. Soldering
16.1 Introduction to soldering through-hole mount packages
This text gives a brief insight to wave, dip and manual soldering. A more in-depth account of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages (document order number 9398 652 90011). Wave soldering is the preferred method for mounting of through-hole mount IC packages on a printed-circuit board.
Suitability of through-hole mount IC packages for dipping and wave soldering methods Soldering method Dipping suitable Wave suitable suitable [1] not suitable
For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board. For PMFP packages hot bar soldering or manual soldering is suitable.
21 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors. Preliminary data 9397 750 10779 -
20040206
22 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
III
Product data
Production
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
19. Denitions
Short-form specication The data in a short-form specication is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values denition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specication is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specied use without further testing or modication.
customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status Production), relevant changes will be communicated via a Customer Product/Process Change Notication (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specied.
21. Trademarks
Notice All referenced brands, product names, service names and trademarks are the property of their respective owners.
20. Disclaimers
Life support These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors
23 of 24
Philips Semiconductors
TDA8947J
4-channel audio amplier
23. Contents
1 2 3 4 5 6 7 7.1 7.2 8 8.1 8.2 8.2.1 8.2.2 8.3 8.4 8.5 9 10 11 12 13 13.1 13.2 13.2.1 13.2.2 13.3 14 14.1 15 16 16.1 16.2 16.3 16.4 17 18 19 20 21 22 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Input conguration . . . . . . . . . . . . . . . . . . . . . . 5 Power amplier . . . . . . . . . . . . . . . . . . . . . . . . . 5 Output power measurement . . . . . . . . . . . . . . . 6 Headroom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Mode selection . . . . . . . . . . . . . . . . . . . . . . . . . 6 Supply voltage ripple rejection . . . . . . . . . . . . . 7 Built-in protection circuits . . . . . . . . . . . . . . . . . 8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 8 Thermal characteristics. . . . . . . . . . . . . . . . . . . 8 Static characteristics. . . . . . . . . . . . . . . . . . . . . 9 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 Application information. . . . . . . . . . . . . . . . . . 15 Application diagrams . . . . . . . . . . . . . . . . . . . 15 Printed-circuit board . . . . . . . . . . . . . . . . . . . . 17 Layout and grounding . . . . . . . . . . . . . . . . . . . 17 Power supply decoupling . . . . . . . . . . . . . . . . 17 Thermal behavior and heatsink calculation . . 18 Test information . . . . . . . . . . . . . . . . . . . . . . . . 19 Quality information . . . . . . . . . . . . . . . . . . . . . 19 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 20 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Introduction to soldering through-hole mount packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Soldering by dipping or by solder wave . . . . . 21 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 21 Package related soldering information . . . . . . 21 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 22 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 23 Denitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Contact information . . . . . . . . . . . . . . . . . . . . 23