Académique Documents
Professionnel Documents
Culture Documents
Photo on title page: Applications for TETRA. Catalogue Issue 10/04 All data published in previous catalog issues hereby becomes invalid. We reserve the right to make alterations in accordance with the requirements of our customers, therefore for binding datas please check valid datasheets!
Please note:
As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions.
The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process.
The details given in our data sheets have to be followed carefully when installing the antennas and accessories. In addition, please use our information brochure about mounting configurations. The installation team must be properly qualified and also be familiar with the relevant national safety regulations.
Internet: www.kathrein.de KATHREIN-Werke KG . Telephone +49 80 31 1 84-0 . Fax +49 80 31 1 84-9 91 Anton-Kathrein-Strae 1 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany
Directional Antennas
360 512 MHz: e.g. TETRA, TETRAPOL, GSM 450, CDMA 450, Trunking system
Omnidirectional Antennas
370 470 MHz: e.g. TETRA, TETRAPOL, GSM 450, CDMA 450, Trunking system
Indoor
370 450 MHz: e.g. TETRA, TETRAPOL, GSM 450, CDMA 450, Trunking system
Electrical Accessories
Mechanical Accessories
Technical Information
3
Antennen Electronic
KATHREINMobilfunkantennen
Antennas for Mobile Communications
ing includ terns on pat radiati i-format in ms
02/04
Antennen Electronic
Subject to alteration
Summary of Types
The articles are listed by type number in numerical order.
Type No.
Page
Type No.
Page
Type No.
Page
Type No.
Page
711 ...
711 530 45
54 55 76 76
K 51 ...
K 51 24 72 K 51 25 42 1 K 51 26 2 K 51 26 41 1 38 40 ... 45 39 39
K 62 ...
K 62 55 21 K 62 55 41 K 62 56 21 K 62 56 41 K 62 57 21 K 62 57 41 66 66 66 66 66 66
713 ...
713 645 80
737 975
K 51 26 42 1
K 63 ...
16 17 K 63 20 22 1 K 63 20 22 7 K 63 20 23 1 67 67 67 67 67 67
739 ...
739 504 739 506 739 990 29 30 31
K 52 07 21 K 52 32 21
K 53 ...
K 53 17 41 11 15 14 10 10
K 63 20 23 7 K 63 20 24 1 K 63 20 24 7
721 ...
721 387 721 388 51 52
741 ...
741 515 741 516 20 21 23 24
K 53 18 21 K 53 19 21 K 53 19 41 1 K 53 19 42 1
K 72 ...
K 72 22 41 K 72 22 47 32 32
728 ...
728 888 728 889 52 57
K 73 ...
K 73 12 21 K 73 23 21 K 73 36 21 K 73 51 21 34 33 25 35
731 ...
731 291 731 651 28 76
733 ...
733 677 733 678 733 679 733 680 733 695 76 76 76 76 74
K 75 ...
K 75 11 21 K 75 15 21 1 50 ... 51 51 52 53 58
800 ...
800 10252 800 10253 800 10278 26 27 62 63
K 61 ...
K 61 14 01 K 61 14 02 K 61 14 03 K 61 14 04 74 74 74 74 74 80 80 80 80
K 75 15 22 1 K 75 16 21 1 K 75 16 37 K 75 29 21
736 ...
736 831 60
800 10330
K 61 14 05 K 61 33 11 K 61 33 21 K 61 33 3 K 61 33 4
Omnidirectional antennas
Design Radome
Small size and elegant design are the distinguishing features of Kathreins antenna families. The radomes cover the internal antenna components. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance, painting and best weather protection. The design of Kathrein antennas is based on fundamental engineering knowledge and also on decades of practical experience, during which the various constructions and materials used have proved their outstanding reliability. Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regards to the following items: Low temperature: 55 C High temperature (dry): +60 C According to the antenna type selected, customer can choose from different half-power beam widths and different gain values. Depending on the type, the antennas are equipped with up to 2 fixing points. Panels can be wall mounted without any additional hardware. For mast mounting, stainless steel brackets and mechanical downtilt kits are available. To assist the installation technicians in aligning the panels, an azimuth adjustment tool can be supplied (see Mechanical Accessories).
Environmental influences
Environmental conditions
Large variety of half-power beam width, gain values Multi-functional installation hardware
Type
Type No.
Input
Page
K 53 19 41 1 K 53 19 42 1 K 53 17 41
10 10 11
68 ... 87.5 H or V
K 53 19 41 1 K 53 19 42 1
68 80 MHz 74 87.5 MHz Usable for horizontal or vertical polarization. 3 dB 50 < 1.5 1300 W (at 50 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from 60 115 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. The antenna will be shipped dismounted.
Mounting:
Grounding:
Special features:
162 77
Mechanical specifications Input Weight Wind load N female 12 kg 260 N (at 150 km/h) 180 km/h 2154 x 798 x 132 mm approx. 2100 mm approx. 1200 mm
10
10
dB
3 0
3 0
in E-plane
in H-plane
10
68 87.5 V
4-element Yagi antenna, large bandwidth. Hot-dip galvanized steel. q Gain 6 dB.
q q
K 53 17 41
68 87.5 MHz Vertical 6 dB 50 < 1.5 100 W (at 50 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from 60 115 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively.
Mounting:
Grounding:
10 dB
10 dB
3 0
3 0
Horizontal 69 MHz
Vertical 69 MHz
120 60
10 dB
10
Mechanical specifications
3 0 3 0 dB
N female 22 kg 520 N (at 150 km/h) 180 km/h 2424 x 2118 x 182 mm approx. 2380 mm approx. 2030 mm
Horizontal 77 MHz
Vertical 77 MHz
80
58
10 dB
10 dB
3 0
3 0
Horizontal 86 MHz
Vertical 86 MHz 11
12
Type
Type No.
Input
Page
170 118 63 65
K K K K
53 53 52 52
19 18 07 32
21 21 21 21
14 15 16 17
146 174 H or V
K 53 19 21
146 174 MHz Usable for horizontal or vertical polarization. 3 dB 50 < 1.4 560 W (at 50 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from 60 125 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded.
Mounting:
Grounding:
170 80
Mechanical specifications Input Weight Wind load N female 6.5 kg 145 N (at 150 km/h) 200 km/h 1124 x 816 x 92 mm approx. 1060 mm approx. 650 mm
10
10
dB
3 0
3 0
in E-plane
in H-plane
14
146 174 H or V
K 53 18 21
146 174 MHz Usable for horizontal or vertical polarization. 4 dB 50 < 1.3 380 W (at 50 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from 60 125 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded.
Mounting:
Grounding:
118 58
Mechanical specifications Input Weight Wind load N female 7.5 kg 170 N (at 150 km/h) 200 km/h 1112 x 92 x 904 mm approx. 1100 mm approx. 750 mm
10
10
3 0
dB
3 0
in E-plane
in H-plane
15
146 174 H or V
K 52 07 21
146 174 MHz Usable for horizontal or vertical polarization. 8.5 dB 50 < 1.5 250 W (at 50 C ambient temperature) Antenna: Weather-resistant aluminum. All screws and nuts: Stainless steel. On masts from 60 105 mm diameter, by means of supplied mounting kit. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. The antenna will be shipped dismounted.
Mounting:
Grounding:
Shipping:
Mechanical specifications
53 63
N female 10 kg Horizontal: 235 N 140 N 210 km/h Vertical: 210 N 140 N 220 km/h
10
10
dB
3 0
3 0
dB
in E-plane
in H-plane
16
146 174 H or V
K 52 32 21
146 174 MHz Usable for horizontal or vertical polarization. 8 dB 50 < 1.15 1100 W (at 50 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. Via pair of clamps K 61 12 0 at masts from 60 115 mm dia. or via pair of clamps K 61 13 0 at masts from 115 210 mm dia. (not supplied). The antenna is especially suitable as a component in arrays to achieve various radiation patterns. All metal parts of the antenna including the mounting kit are DC grounded. Fiberglass enclosure of its critical points and the antennas extremely sturdy construction keep it operational even during heavy icing.
Mounting:
Combination:
Grounding:
Ice protection:
Mechanical specifications
58 65
N female 25 kg 660 N (at 150 km/h) 220 km/h 1400 x 1400 x 750 mm 1320 x 1320 x 510 mm
10
10
Packing size
dB
3 0
dB
3 0
Width/height/depth
in E-plane
in H-plane
17
18
Type
Type No.
Height [mm] 992 2000 2000 1007 1997 493 992 2000 992 974 1934 350 353 353 400 500 718
Input
Page
XPol Panel 380500 XPol Panel 380500 XPol Panel 380430 XPol Panel 380500 XPol Panel 380500 VPol Panel 406512 VPol Panel 380500 VPol Panel 380500 VPol Panel 400470 VPol Panel 380430 VPol Panel 380430 LogPer 440512/824960 LogPer 406512 LogPer 406512 LogPer 406512 Corner 360490 RHCPol Helix 400470
12dBi 15dBi 14.5dBi 6T 10.5dBi 13.5dBi 9dBi 12dBi 15dBI 9dBi 8.5dBi 11.5dBi 10.5/11.5dBi 10.5dBi 10.5dBi 9dBi 11dBi 12dBi
741 515 741 516 742 242 741 517 741 518 K 73 36 21 800 10252 800 10253 731 291 739 504 739 506 739 990 K 72 22 41 K 72 22 47 K 73 23 21 K 73 12 21 K 73 51 21
2 x 7-16 female 2 x 7-16 female 2 x 7-16 female 2 x 7-16 female 2 x 7-16 female N female 7-16 female 7-16 female 7-16 female 7-16 female 7-16 female 7-16 female N female 7-16 female N female N female N female
20 21 22 23 24 25 26 27 28 29 30 31 32 32 33 34 35
19
380 500 X 65
741 515
380 500 430 500 MHz +45, 45 12 dBi
Ice protection:
910
250
380 500 45
7-16
7-16
+45/ 45 Polarization
Mechanical specifications Input 2 x 7-16 female Rearside 12 kg Frontal: Lateral: Rearside: 550 N (at 150 km/h) 220 N (at 150 km/h) 715 N (at 150 km/h) 200 km/h 1062 x 562 x 274 mm 992 / 492 / 190 mm
120
65 36
10
10
dB
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern
20
415
Grounding:
380 500 X 65
741 516
380 500 430 500 MHz +45, 45 15 dBi 65 18
1850
> 30 dB
Ice protection:
Grounding:
7-16
800
7-16
+45/ 45 Polarization
65 18
Mechanical specifications Input 2 x 7-16 female Rearside 19 kg Frontal: 1100 N (at 150 km/h) Lateral: 440 N (at 150 km/h) Rearside: 1540 N (at 150 km/h) 200 km/h 2060 x 562 x 274 mm 2000 / 492 / 190 mm
120
10
10
dB
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern
21
380 430 X 68 6
742 242
380 430 MHz +45, 45 14.5 dBi Horizontal: Vertical: 6, fixed > 25 dB 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) Radiators: Tin-plated copper. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 380 500 45 380 500 +45
250
68 18
1850
> 30 dB
Ice protection:
Grounding:
7-16
800
7-16
+45/ 45 Polarization
68 18
Mechanical specifications Input 2 x 7-16 female Rearside 19 kg Frontal: 1100 N (at 150 km/h) Lateral: 440 N (at 150 km/h) Rearside: 1540 N (at 150 km/h) 200 km/h 2060 x 562 x 274 mm 2000 / 492 / 190 mm
130
10 3 0
10
dB
dB
3 0
Horizontal Pattern
22
380 500 X 88
741 517
380 500 430 500 MHz +45, 45 2 x 10.5 dBi Horizontal: Vertical: > 20 dB > 30 dB 50 < 1.5 86 35
35
10
10 3 0
380 500 45
dB
dB
3 0
7-16
7-16
Horizontal Pattern
Vertical Pattern
Input
40
2 x 7-16 female Bottom 10.5 kg Frontal: Lateral: 360 N (at 150 km/h) 220 N (at 150 km/h) 200 km/h 1140 x 330 x 240 mm 1007 / 317 / 193 mm
10
10 3 0
dB
3 0
dB
Horizontal Pattern
Vertical Pattern
Height/width/depth
23
380 500 X 88
741 518
380 500 430 500 MHz +45, 45 2 x 13.5 dBi Horizontal: Vertical: > 20 dB > 30 dB 50 < 1.5 86 17
17
10
10 3 0
380 500 45
dB
dB
3 0
7-16
7-16
Horizontal Pattern
Vertical Pattern
Input
20
2 x 7-16 female Bottom 18.5 kg Frontal: Lateral: 715 N (at 150 km/h) 440 N (at 150 km/h) 200 km/h 2130 x 330 x 240 1997 / 317 / 193 mm
10
10 3 0
dB
3 0
dB
Horizontal Pattern
Vertical Pattern
Height/width/depth
24
406 512 V 63
K 73 36 21
406 512 MHz Vertical 9 dBi H-plane: 63 E-plane: 63 50 < 1.4 < 150 dBc 500 W (at 50 C ambient temperature) This antenna is especially suitable as a component in arrays to achieve various radiation patterns. Antenna including two weather-proof covers for straight and elbow connector, but without mounting hardware.
40 0
Scope of supply:
Material:
Dipoles and reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. Use clamps K 61 14 0 .. for tubular mast diameters of 40 521 mm (see the Mechanical Accessories part of this catalogue). Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled.
18
Attachment:
Ice protection:
Mounting Dimensions
Grounding:
Mechanical specifications
63 63
N female Rearside 6 kg Frontal: Lateral: Rearside: 220 N (at 150 km/h) 100 N (at 150 km/h) 330 N (at 150 km/h) 200 km/h 603 x 567 x 282 mm 493 / 493 / 209 mm
10 dB
10 dB
Wind load
3 0
3 0
Horizontal Pattern
Vertical Pattern
25
380 500 V 65
800 10252
380 500 430 500 MHz Vertical 12 dBi Horizontal: Vertical: > 20 dB 63 32
136
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern
dB
Mechanical specifications Input 1 x 7-16 female Rearside 12 kg Frontal: Lateral: Rearside: 550 N (at 150 km/h) 220 N (at 150 km/h) 715 N (at 150 km/h) 200 km/h 1062 x 562 x 274 mm 992 / 492 / 190 mm
122
10 3 0
10
dB
dB
3 0
Horizontal Pattern
Vertical Pattern
26
380 500 V 65
800 10253
380 500 430 500 MHz Vertical 15 dBi Horizontal: Vertical: > 20 dB 63 16
136
10 3 0
10
dB
3 0
Horizontal Pattern
Vertical Pattern
dB
Mechanical specifications Input 1 x 7-16 female Rearside 20 kg Frontal: 1100 N (at 150 km/h) Lateral: 440 N (at 150 km/h) Rearside: 1540 N (at 150 km/h) 200 km/h 2060 x 562 x 274 mm 2000 / 492 / 190 mm
122
10 3 0
10
dB
dB
3 0
Horizontal Pattern
Vertical Pattern
27
731 291
400 470 MHz Vertical 9 dBi H-plane: 120 E-plane: 50 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) Antenna including two weather-proof covers for straight and elbow connector, but without mounting hardware. Dipole system: Brass and copper. Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. Use clamps K 61 14 0 .. for tubular mast diameters of 40 521 mm (see the Mechanical Accessories part of this catalogue).
91 0
Material:
Attachment:
Ice protection:
Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded.
63
Grounding:
Mounting Dimensions
120 50
Mechanical specifications Input Connector position 7-16 female Rearside 9 kg Frontal: Lateral: Rearside: 500 N (at 150 km/h) 220 N (at 150 km/h) 715 N (at 150 km/h) 200 km/h 1062 x 562 x 274 mm 992 / 492 / 190 mm
10
10
Weight
dB
3 0
dB
Wind load
3 0
Horizontal Pattern
Vertical Pattern
28
739 504
380 430 MHz Vertical 8.5 dBi H-plane: 115 E-plane: 38 > 18 dB 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) Radiator: Copper, tin-plated. Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. See the Mechanical Accessories part of this catalogue. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded.
Attachment:
Ice protection:
Grounding:
115
7-16 female Bottom 4.5 kg Frontal: Lateral: Rearside: 160 N (at 150 km/h) 100 N (at 150 km/h) 360 N (at 150 km/h) 200 km/h 1102 x 272 x 160 mm 974 / 258 / 103 mm
10
10
dB
Wind load
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern
29
739 506
380 430 MHz Vertical 11.5 dBi H-plane: 115 E-plane: 18 > 18 dB 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) Radiator: Copper, tin-plated. Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. See the Mechanical Accessories part of this catalogue. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded.
Attachment:
Ice protection:
Grounding:
115
7-16 female Rearside 9 kg Frontal: Lateral: Rearside: 340 N (at 150 km/h) 220 N (at 150 km/h) 750 N (at 150 km/h) 200 km/h 2062 x 272 x 160 mm 1934 / 258 / 103 mm
10
10
Wind load
dB
3 0
dB
3 0
Horizontal Pattern
Vertical Pattern
30
739 990
440 512 MHz Vertical 10.5 dBi H-plane: 68 E-plane: 54 > 23 dB 50 < 1.4 < 150 dBc 100 W (at 50 C ambient temperature) Radiator: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. The antenna can be mounted on tubular mast with a diameter of 48 115 mm with supplied clamps. The radiation system ist protected by the radome. Due its very sturdy construction, the antenna remains operational even under icy conditions. All metal parts of the antenna including the inner conductor are DC grounded. 824 960 Vertical 11.5 dBi H-plane: 60 E-plane: 48 > 25 dB
Mounting:
Ice protection:
Grounding:
54
10 dB
10 dB
3 0
3 0
7-16 female Bottom 9 kg Frontal: Lateral: 55 N (at 150 km/h) 440 N (at 150 km/h) 180 km/h 1172 x 372 x 225 mm 1160 / 350 / 170 mm
10 dB
10 dB
3 0
3 0
Height/width/depth
31
406 512 V or H 67
K 72 22 41 K 72 22 47
406 512 MHz Usable for horizontal or vertical polarization. 10.5 dBi H-plane: 67 E-plane: 53 > 25 dB at 440 512 MHz > 20 dB at 406 512 MHz 50 < 1.4 < 150 dBc For horizontal polarization 300 W (at 50 C ambient temperature) Several antennas can be combined to increase the gain and to produce radiation patterns with very high side-lobe suppressions. Antenna with weather protective casing for straight connectors. Radiator and mounting kit: Aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. To tubular masts of 48 115 mm diameter using supplied clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. For horizontal polarization For vertical polarization For vertical polarization
Scope of supply:
Material:
Attachment:
Ice protection:
Grounding:
Mechanical specifications
67
K 72 22 47 7-16 female
53
10 dB
10
Horizontal:
3 0
3 0
dB
32
406 512 V 87
K 73 23 21
406 512 MHz Vertical 9 dBi H-plane: 87 E-plane: 62 > 28 dB at 440 512 MHz > 21 dB at 406 512 MHz 50 < 1.3 < 150 dBc 500 W (at 50 C ambient temperature) Antenna with weather protective casing for straight connectors. Radiator: Weather-resistant aluminum. Radome: Fiberglass, colour: White. Mounting kit: Hot-dip galvanized steel. All screws and nuts: Stainless steel. To tubular masts of 60 115 mm diameter using supplied clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded.
Material:
Attachment:
Ice protection:
Grounding:
87
62
10 dB
10 dB
3 0
3 0
Mechanical specifications Input Connector position N female Rearside 8.3 kg Frontal: Lateral: 54 N (at 150 km/h) 150 N (at 150 km/h) 180 km/h 960 x 470 x 470 mm 860 / 400 / 400 mm
Horizontal Pattern
Vertical Pattern
33
360 490 V 44
K 73 12 21
360 490 MHz Vertical 11 dBi H-plane: 44 E-plane: 67 50 < 1.5 at 360 490 MHz < 1.3 at 400 470 MHz < 150 dBc 180 W (at 50 C ambient temperature) Antenna with weather protective casing for straight connectors, mounting kit included. Radiator and reflector: Weather-resistant aluminum. Mounting U-bold: Stainless steel. All screws and nuts: Stainless steel. To tubular masts of 30 54 mm diameter using supplied U-bolts. The reflector screen folds together for transport. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded.
Material:
Attachment:
44
67
Mechanical specifications Input Weight N female 2.8 kg 140 N (at 150 km/h) 150 km/h 842 x 524 x 187 mm 500 / 1155 / 577 mm
10 dB
10 dB
3 0
3 0
Horizontal Pattern
Vertical Pattern
34
K 73 51 21
400 470 MHz Right handed circular 12 dBi (ref. to the circularly polarized isotropic antenna) 33 50 < 1.2 560 W (at 50 C ambient temperature) Antenna with weather protective casing for straight connectors, mounting kit included. Antenna: Copper band helix in protective fiberglass tube, colour: Grey. Reflector screen: Weather-resistant aluminum. Attachment construction: Hot dip galvanized steel. All screws and nuts: Stainless steel. To tubular masts of 60 125 mm diameter using supplied U-bolts. The reflector screen is made of two parts and can be removed for transport. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded.
Material:
Attachment:
Special features:
Grounding:
Mounting Instructions
Mechanical specifications
33
Input Weight
N female 12 kg Frontal: Lateral: 450 N (at 150 km/h) 175 N (at 150 km/h) 200 km/h 1684 x 388 x 277 mm 718 mm 1540 / 204 mm
10 dB
Wind load Max. wind velocity Packing size Reflector diameter Length / tube dia.
3 0
35
36
Type
Type No.
Input
Page
K K K K K
51 51 51 51 55
24 26 26 25 28
72 41 1 42 1 42 1 41
38 39 39 40 41
27 ... 61 V
K 51 24 72
K 51 24 70 1 27 ... 61 MHz Vertical
dipole)
0 dB 50 500 W (at 50 C ambient temperature) Radiator and radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 54 mm diameter (connecting cable runs outside the mast). By cutting radiator and radials to length in accordance to the mounting instructions. The metal parts of the antenna including the mounting kit are DC grounded.
Mounting:
Tuning:
Grounding:
78
10
3 0
Vertical Pattern
dB
Mechanical specifications Input UHF female 1.6 kg 110 N (at 150 km/h) 135 km/h 2704 x 136 x 100 mm max. 2510 mm max. 2510 mm
Weight * Wind load * Max. wind velocity Packing size Radiator length Length of radials * for max. antenna length
38
68 ... 87.5 V
K 51 26 41 1: VPol Omni 6880 360 0dB K 51 26 42 1: VPol Omni 7487.5 360 0dB
Type No. Antenna Spare radials
K 51 26 41 1 K 51 26 42 1
K 51 26 40 12 68 80 MHz Vertical 0 dB 50 < 1.5 75 W (at 50 C ambient temperature) Radiator: Stainless steel. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 40 mm diameter (connecting cable runs outside the mast). See catalogue part Technical Information. All metal parts of the antenna including the mounting kit are DC grounded. K 51 26 40 22 74 87.5 MHz
Frequency range Polarization Gain (ref. /2 dipole) Impedance VSWR Max. power Material:
Mounting:
Mechanical specifications
78
K 51 26 41 1
K 51 26 42 1
N female 1.6 kg 65 N 200 km/h 1114 x 132 x 112 mm 747 mm 1053 mm 680 mm 970 mm
10
10
dB
3 0
3 0
Horizontal Pattern
Vertical Pattern
39
167.5 174 V
K 51 25 42 1
K 51 25 40 2 74.2 77.7 MHz and 84.0 87.5 MHz Vertical 0 dB 50 < 1.5 10 W (at 50 C ambient temperature) Radiator: Weather-resistant aluminum in fiberglass radome. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. To pipes of 30 54 mm diameter by means of mounting kit (supplied). The antenna must be mounted in such a manner, that the feeder cables runs outside the mast. The radials can be fold up. All metal parts of the antenna including the mounting kit are DC grounded. 0.5 dB 167.5 174 MHz
Frequency range Polarization Gain (ref. /2 dipole) Decoupling Impedance VSWR Max. power Material:
Mounting:
Mechanical specifications
78
2 x N female 2.7 kg 90 N (at 150 km/h) 180 km/h 1160 x 120 x 110 mm 1121 mm 50 mm 1003 mm
10
10
3 0
dB
3 0
Horizontal Pattern
Vertical Pattern
40
68 87.5 V
K 55 28 41
68 87.5 MHz Vertical Preferred direction: mast to radiator. 2 dB 50 < 1.5 230 W (at 50 C ambient temperature) Hot-dip galavanized steel. Radome: Fiberglass. All screws and nuts: Stainless steel. On masts from 60 115 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively.
Mounting:
Grounding:
Mechanical specifications
78
N female 9 kg 165 N (at 150 km/h) 200 km/h 60 115 mm 1800 x 948 x 107 mm approx. 1750 mm approx. 870 mm
10
10
3 0
dB
3 0
Horizontal Pattern
Vertical Pattern
41
42
Type
Type No.
Height [mm] 1 1880 905 905 1085 1042 993 4830 4645 4330 840
Input
Page
VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol
Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni
74.287.5/167.5174 146174 146174 146156 155165 164174 146156 155164 164174 146174
360/360 360 360 360 360 360 360 360 360 360
0/0.5dB 0dB 0dB 0dB 0dB 0dB 4dB 4dB 4dB 2dB
K 51 25 42 K 51 26 2 711 530 K 55 26 26 K 55 26 27 K 55 26 28 K 55 16 21 K 55 16 22 K 55 16 23 K 55 29 21
1 1 1
2 x N female cable termination N female cable termination cable termination cable termination cable termination cable termination cable termination N female
44 45 45 46 46 46 47 47 47 48
43
167.5 174 V
K 51 25 42 1
K 51 25 40 2 74.2 77.7 MHz and 84.0 87.5 MHz Vertical 0 dB 50 < 1.5 10 W (at 50 C ambient temperature) Radiator: Weather-resistant aluminum in fiberglass radome. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. To pipes of 30 54 mm diameter by means of mounting kit (supplied). The antenna must be mounted in such a manner, that the feeder cables runs outside the mast. The radials can be fold up. All metal parts of the antenna including the mounting kit are DC grounded. 0.5 dB 167.5 174 MHz
Frequency range Polarization Gain (ref. /2 dipole) Decoupling Impedance VSWR Max. power Material:
Mounting:
Mechanical specifications
78
2 x N female 2.7 kg 90 N (at 150 km/h) 180 km/h 1160 x 120 x 110 mm 1121 mm 50 mm 1003 mm
10
10
3 0
dB
3 0
Horizontal Pattern
Vertical Pattern
44
146 174 V
K 51 26 2
K 51 26 20 2 Vertical
711 530
K 51 26 20 2
dipole)
0 dB 50 < 1.5 170 W 700 W (at 50 C ambient temperature) Radiator and radials: Weather-resistant aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 40 mm diameter (connecting cable runs outside the mast). See catalogue part Mechanical Accessories. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled.
Material:
Mounting:
Mechanical specifications
78
Input
10
10
Weight
dB
dB
3 0
3 0
Wind load Max. wind velocity Packing size Radiator length Length of radials
Horizontal Pattern
Vertical Pattern
K 55 26 26: VPol Omni 146156 360 0dB K 55 26 27: VPol Omni 155164 360 0dB K 55 26 28: VPol Omni 164174 360 0dB
Type No. Frequency range Polarization Gain (ref. /2 dipole) Impedance VSWR Max. power Material:
K 55 26 26 K 55 26 27 K 55 26 28
146 156 MHz 155 165 MHz Vertical 0 dB 50 < 1.4 130 W (at 50 C ambient temperature) Radiator and base: Weather-resistant aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 40 mm diameter (connecting cable runs outside the mast). See catalogue part Mechanical Accessories. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled. 164 174 MHz
Mounting:
10
3 0
dB
K 55 26 26
K 55 26 27
K 55 26 28
Via terminals inside antenna. RG-213/U 1.3 kg 50 N (at 150 km/h) 200 km/h 1254 x 112 x 97 mm 1085 mm 1042 mm 993 mm
10
Wind load
dB
3 0
Vertical Pattern
46
K 55 16 21 1: VPol Omni 146156 360 4dB K 55 16 22 1: VPol Omni 155164 360 4dB K 55 16 23 1: VPol Omni 164174 360 4dB
Type No. Frequency range Polarization Gain (ref. /2 dipole) Impedance VSWR Max. power Material:
K 55 16 21 1 K 55 16 22 1 K 55 16 23 1
146 156 MHz 155 164 MHz Vertical 4 dB 50 < 1.5 500 W (at 50 C ambient temperature) Radiator: Brass. Radome: Fiberglass, colour:Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 65 105 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 30 90 mm diameter (connecting cable runs outside the mast). All metal parts of the antenna including the mounting kit are DC grounded. 164 174 MHz
Mounting:
Grounding:
10
3 0
dB
K 55 16 21 1
K 55 16 22 1 N female
K 55 16 23 1
7 kg 280 N
6.5 kg 250 N
10
3 0
dB
5011 mm
4511 mm
Vertical Pattern
4830 mm
4645 mm max. 52 mm
4330 mm
47
146 174 V
K 55 29 21
146 174 MHz Vertical Preferred direction: Mast to radiator. 2 dB 50 < 1.4 440 W (at 50 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts of 60 125 mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded.
Mounting:
Grounding:
10 dB
10 dB
3 0
3 0
Horizontal Pattern 60 mm
Mechanical specifications Input N female 4.5 kg 90 N (at 150 km/h) 200 km/h 60 125 mm 864 x 598 x 87 mm 840 mm 500 mm
78
78
10 dB
10 dB
3 0
3 0
Vertical Pattern 60 mm
48
Type
Type No.
Height [mm] 552 510 1273 1144 1144 2020 2016 2016 2016 2840 3281.5 3114 3113 4430 4175 315
Input
Page
VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol VPol
Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni Omni
370430 406470 406430 440470 440470 406430 406430 440470 440470 380400 380400 410430 450470 406430 440470 400470
360 360 360 360 360 360 360 360 360 360 360 360 360 360 360 360
2dBi 2dBi 5dBi 5dBi 5dBi 7dBi 7 dBi 7dBi 7dBi 7.5dBi 7.5dBi 8.5T 8dBi 8.5T 8.5dBi 10dBi 10dBi 4dBi
737 003 K 75 11 21 K 75 15 21 1 K 75 15 22 1 721 387 K 75 16 21 1 728 888 721 388 720 880 K 75 16 37 737 545 737 546 742 155 728 889 720 842 K 75 29 21
N female N female N female N female N female N female 7-16 female N female 7-16 female 7-16 female 7-16 female 7-16 female 7-16 female 7-16 female 7-16 female N female
50 50 51 51 51 52 52 52 52 53 54 55 56 57 57 58
49
737 003: VPol Omni 370430 360 2dBi K 75 11 21: VPol Omni 406470 360 2dBi
Type No. Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Material:
737 003
370 430 MHz
K 75 11 21
406 470 MHz Vertical 2 dBi 50 < 1.5
< 150 dBc 100 W (at 50 C ambient temperature) Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 40 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 20 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded.
Mounting:
Grounding:
Mechanical specifications
78
737 003
K 75 11 21 N female Bottom
0.8 kg 21 mm
10 3 0 dB
Wind load Max. wind velocity Packing size [mm] Height [mm]
20 N (at 150 km/h) 200 km/h 112 x 97 x 654 552 112 x 97 x 614 510
Vertical Pattern
50
K 75 15 21 1: VPol Omni 406430 360 5dBi K 75 15 22 1: VPol Omni 440470 360 5dBi 721 387: VPol Omni 440470 360 5dBi
Type No. Frequency range Polarization Gain Impedance VSWR Max. power 55 W
K 75 15 21 1 K 75 15 22 1
406 430 MHz Vertical 5 dBi 50 < 1.5 55 W (at 50 C ambient temperature)
721 387
500 W
Material:
Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 40 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 20 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded.
Mounting:
Grounding:
K 75 15 21 2
721 387
10 dB
3 0
Vertical Pattern
51
K 75 16 21 1: VPol Omni 406430 360 7dBi 721 388, 720 880: VPol Omni 440470 360 7dBi 728 888: VPol Omni 406430 360 7dBi
Type No.
K 75 16 21 1
406 430 MHz
728 888
406 430 MHz
Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power
70 W
18
10 dB
3 0
Mechanical specifications N female 7-16 female Connector position Weight Radome diameter Wind load Max. wind velocity Packing size [mm] Height 2100 x 110 x 100 2020 mm K 75 16 21 1 721 388 720 880 Bottom 1.6 kg 21 mm 60 N (at 150 km/h) 200 km/h 112 x 97 x 2124 2016 mm 728 888
Vertical Pattern
52
380 400 V
K 75 16 37
380 400 MHz Vertical 7.5 dBi 50 < 1.5 500 W (at 50 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, dia. 51 mm, colour: Grey. Base: Aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 50 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm2. The inner conductor is capacitively coupled.
Mounting:
Grounding:
um maxim p to mast
17
104
10
dB
Mechanical specifications
0
Vertical Pattern
Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height
150
7-16 female Bottom 8.0 kg 51 mm 200 N (at 150 km/h) 200 km/h 3316 x 148 x 112 mm 2840 mm
230
53
737 545
380 400 MHz Vertical 7.5 dBi 8.5, fixed 50 < 1.5 500 W (at 50 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 50 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm2. The inner conductor is capacitively coupled.
Mounting:
Grounding:
um maxim p to mast
14
104
10
3 0
dB
Mechanical specifications Vertical Pattern 8.5 electrical downtilt Input Connector position Weight Radome diameter Windload Max. wind velocity Packing size Height 7-16 female Bottom 8.5 kg 51 mm 230 N (at 150 km/h) 180 km/h 3550 x 148 x 112 mm 3281.5 mm
54
150
230
737 546
410 430 MHz Vertical 8 dBi 8.5, fixed 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 50 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm2. The inner conductor is capacitively coupled.
Mounting:
Grounding:
um maxim p to mast
14
104
10
3 0
dB
Mechanical specifications Vertical Pattern 8.5 electrical downtilt Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8.0 kg 51 mm 220 N (at 150 km/h) 180 km/h 3376 x 196 x 102 mm 3114 mm
150
230
55
450 470 V
742 155
450 470 MHz Vertical 8.5 dBi 50 < 1.5 < 150 dBc 500 W (at 50 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. The antenna can be attached laterally at the tip of any tubular mast of 50 94 mm diameter (connecting cable runs outside the mast). The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm2. The inner conductor is coupled capacitively.
Mounting:
Grounding:
um maxim p to mast
12
104
10
3 0
dB
Mechanical specifications Vertical Pattern Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8.0 kg 51 mm 220 N (at 150 km/h) 180 km/h 3379 x 206 x 152 mm 3113 mm
56
150
230
728 889: VPol Omni 406430 360 10dBi 720 842: VPol Omni 440470 360 10dBi
Type No. Frequency range Polarization Gain Impedance VSWR Max. power Material:
728 889
406 430 MHz Vertical 10 dBi 50 < 1.5
720 842
440 470 MHz
500 W (at 50 C ambient temperature) Radiator: Brass. Radome: Fiberglass, dia. 30 52 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 65 105 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 30 90 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded.
Mounting:
Grounding:
10 dB
3 0
Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height
728 889
720 842
Vertical Pattern
7-16 female Bottom 7.0 kg 30 52 mm 240 N 230 N (at 150 km/h) 150 km/h 4600 x 198 x 152 mm 4430 mm 4175 mm 6.5 kg
57
400 470 V
Omnidirectional antenna with variable antenna-to-mast distance. Depending on the distance of the radiator from the mast edge and also on the mast diameter, various radiation patterns can be achieved.
K 75 29 21
400 470 MHz Vertical 4 dBi 50 < 1.5 450 W (at 50 C ambient temperature) Radiator: Hot-dip galvanized steel. Horizontal support pipe: Stainless steel. Mount: Aluminum. Tightening band and all screws and nuts: Stainless steel. Feedpoint radome: Fiberglass. To tubular masts of 60 320 mm diameter using supplied stainless steel tightening band (20 mm wide, 0.8 mm gauge). The distance from tubular mast to radiator is adjustable from 170 580 mm. All metal parts of the antenna including the inner conductor and the supplied mount are DC grounded.
Attachment:
Special features:
Grounding:
Horizontal radiation pattern: Depending on the distance A (edge of pipe mast to dipole) see sketch.
Mechanical specifications Input Weight N female 1.6 kg 40 N (at 150 km/h) 200 km/h 880 x 330 x 100 mm 315 mm
A A ncd ne istta sa D b
58
60 60 61 61
380405 405430
90 90
7dBi 7dBi
N female N female
62 63
59
406 . . . 470 V
737 299: VPol Indoor 406430 360 2dBi 736 831: VPol Indoor 450470 360 2dBi
Type No. Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Material:
737 299
406 430 MHz Vertical 2 dBi 50 < 1.5
736 831
450 470 MHz
< 150 dBc 50 W (at 50 C ambient temperature) Dipole: Brass. Radome: Fiberglass, colour: White. Additional mounting plate: Aluminum. a) Single-hole mounting (12 mm diameter) on surface of up to 10 mm thickness. b) On surfaces of more than 10 mm thickness, by means of mounting plate included in the scope of delivery. All metal parts of the antenna including the inner conductor are DC grounded.
Mounting:
Grounding:
a)
b)
min. 22
max.10 mm
Ceiling
Ceiling
90
Mechanical specifications Input Weight Radome diameter Mounting plate Packing size Height
737 299
736 831
Cable RG 58/CU of 1 m length, grey, connector is not supplied 0.25 kg 20 mm 115 x 25 mm Foil: 650 x 130 mm 400 mm 360 mm 0.23 kg
60
737 003: VPol Omni 370430 360 2dBi K 75 11 21: VPol Omni 406470 360 2dBi
Type No. Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Material:
737 003
370 430 MHz
K 75 11 21
406 470 MHz Vertical 2 dBi 50 < 1.5
< 150 dBc 100 W (at 50 C ambient temperature) Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 40 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 20 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded.
Mounting:
Grounding:
Mechanical specifications
78
737 003
K 75 11 21 N female
??? Bottom ??? 1.0 kg 21 mm 20 N (at 150 km/h) 200 km/h 112 x 97 x 654 552 112 x 97 x 614 510 0.8 kg
10 3 0 dB
Wind load Max. wind velocity Packing size [mm] Height [mm]
Vertical Pattern
61
380 405 V 90
800 10278
380 405 MHz Vertical 7 dBi Horizontal: 90 50 < 2.0 50 W (at 50 C ambient temperature) N female connector IP 30 500 g approx. 320 x 250 x 60 mm approx. 290 x 240 x 45 mm Reflector: Aluminum. Radome: PS, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Two holes of 6 mm diameter in the mounting plate. Screws are not supplied All metal parts inclusive the inner conductor are DC grounded.
10 dB
90
Mounting:
Grounding:
3 0
Horizontal Pattern
62
405 430 V 90
800 10330
405 430 MHz Vertical 7 dBi Horizontal: 90 50 < 2.0 50 W (at 50 C ambient temperature) N female connector IP 30 500 g approx. 320 x 250 x 60 mm approx. 290 x 240 x 45 mm Reflector: Aluminum. Radome: PS, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Two holes of 6 mm diameter in the mounting plate. Screws are not supplied All metal parts inclusive the inner conductor are DC grounded.
10 dB
90
Mounting:
Grounding:
3 0
Horizontal Pattern
63
64
75 MHz
Type 2-way Splitter 3-way Splitter 4-way Splitter 75 MHz 75 MHz 75 MHz Type No. K 62 55 41 K 62 56 41 K 62 57 41 Frequency Range 68 88 MHz 68 88 MHz 68 88 MHz Height 950 mm 1055 mm 1195 mm Input N female N female N female Max. Power 960 Watt 960 Watt 960 Watt Page 66 66 66
150 MHz
Type 2-way Splitter 3-way Splitter 4-way Splitter 150 MHz 150 MHz 150 MHz Type No. K 62 55 21 K 62 56 21 K 62 57 21 Frequency Range 146 174 MHz 146 174 MHz 146 174 MHz Height 530 mm 630 mm 730 mm Input N female N female N female Max. Power 680 Watt 680 Watt 680 Watt Page 66 66 66
450 MHz
Type 2-way Splitter 2-way Splitter 3-way Splitter 3-way Splitter 4-way Splitter 4-way Splitter 450 MHz 450 MHz 450 MHz 450 MHz 450 MHz 450 MHz Type No. K 63 20 22 1 K 63 20 22 7 K 63 20 23 1 K 63 20 23 7 K 63 20 24 1 K 63 20 24 7 Frequency Range 380 512 MHz 380 512 MHz 380 512 MHz 380 512 MHz 380 512 MHz 380 512 MHz Height 409 mm 409 mm 409 mm 409 mm 409 mm 409 mm Input N female 7-16 female N female 7-16 female N female 7-16 female Max. Power 500 Watt 1000 Watt 500 Watt 1000 Watt 500 Watt 1000 Watt Page 67 67 67 67 67 67
tion orma ed inf gues etail For d he catalo s, biner see t , Com rs Filte ifiers ations Ampl nic ommu bile C o for M
68 + 69
65
Electrical Accessories
Power Splitters
For outdoor and indoor use. 2-way Splitter 75 3-way Splitter 75 4-way Splitter 75
Type No. Connector (female) Max. power For connecting ... antennas Frequency range VSWR Impedance Insertion loss Length L K 62 55 41 K 62 56 41 K 62 57 41
0 16
160 mm
N 960 W (at 50 C ambient temperature) 2 3 4 68 88 MHz < 1.1 50 < 0.05 dB 950 mm 1055 mm 1195 mm
For outdoor and indoor use. 2-way Splitter 150 3-way Splitter 150 4-way Splitter 150
Type No. Connector (female) Max. power For connecting ... antennas Frequency range VSWR Impedance Insertion loss Lenth L Material: K 62 55 21 K 62 56 21 K 62 57 21
N 680 W (at 50 C ambient temperature) 2 3 4 146 174 MHz < 1.1 50 < 0.05 dB 530 mm 630 mm 730 mm Protective case on the antenna side: Aluminum. Weather protectition on the equipment side: UV-resistant Elastomere. Transformation line: Aluminum and brass. All parts with protectition varnish. On tubular masts of 60 320 mm dia. OD by means of non-corrosive clamp-strap (1020 x 20 x 1 mm, supplied). Transformers with a total length of over 700 mm are delivered with a supporting clamp.
Mounting:
Equipment
66
Power Splitters
For outdoor and indoor use. 2-way Splitter 390/420/450 3-way Splitter 390/420/450 4-way Splitter 390/420/450
Type No. Connectors (female) Max. power For connecting ... antennas Frequency range VSWR Impedance Insertion loss Packing size Max. size Material: K 63 20 22 1 N 500 W 2 K 63 20 22 7 7-16 1000 W K 63 20 23 1 K 63 20 23 7 N 7-16 500 W 1000 W (at 50 C ambient temperature) 3 380 512 MHz < 1.1 50 < 0.05 dB 425 x 93 x 107 mm 409 x 82 x 82 mm K 63 20 24 1 N 500 W 4 K 63 20 24 7 7-16 1000 W
Case: Aluminum. Inner conductor: Brass. Bracket for wall mounting included in the scope of supply. For mounting to tubular masts use clamps as listed below (order separately).
Mounting:
K 63 20 24 7
Clamps
Type No. 734 734 734 734 734 360 361 362 363 364 Description 2 2 2 2 2 clamps clamps clamps clamps clamps Mast Diameter 30 55 mm 55 75 mm 75 95 mm 95 115 mm 115 135 mm 734 364
67
Band-pass Filter
K 64 21 45 1 K 64 21 25 1 K 65 21 25 1 790 965 790 964 790 967 790 966 68 87.5 MHz 146 174 MHz 380 470 MHz 146 174 MHz 146 174 MHz 380 470 MHz 380 470 MHz
K 65 21 25 1
790 967
S-P Filter
K K K K 64 64 64 65 21 21 21 21 46 47 26 26 1 1 1 1 68 87.5 MHz 68 87.5 MHz 146 174 MHz 380 470 MHz
Duplexer
718 987 719 069 719 628 718 388 718 785 718 290 K 64 41 43 K 64 41 44 K 64 41 23 K 64 41 24 K 65 41 25 K 65 41 26 782 10197 782 10198 790 752 791 055 791 104 791 607 792 025 68 87.5 MHz 68 87.5 MHz 146 174 MHz 146 174 MHz 400 470 MHz 400 470 MHz 68 87.5 MHz 68 87.5 MHz 146 174 MHz 146 174 MHz 389 470 MHz 380 470 MHz 380 385 / 390 395 MHz 385 390 / 395 400 MHz 410 415 / 420 425 MHz 410 415 / 420 425 MHz 415 420 / 425 430 MHz 415 420 / 425 430 MHz 450 455/ 460 465 MHz
K 64 21 26 1
718 628 K 64 41 23
790 752
782 10197
Multiband Combiner
K 64 50 4 721 138 790 244 782 954 722 437
68
68 68 68 68 68
87.5 / 146 174 MHz 174 / 380 470 MHz 174 / 400 470 MHz 470 / 870 970 MHz 470 / 870 970 MHz
728 954
3-dB Coupler
K 62 70 41 K 62 70 21 K 63 70 21 68 108 MHz 140 180 MHz 340 512 MHz
K 62 70 41
725 871
Circulator
793 793 780 791 790 276 277 060 630 215 68 88 MHz 146 174 MHz 146 174 MHz 400 470 MHz 400 470 MHz
780 060
DC-stop
721 062 68 470 MHz
721 062
50-Ohm Loads
K K K K 62 62 62 62 26 26 26 26 11 1 41 1 21 1 30 1 2W 10 W 25 W 50 W 0 0 0 0 2500 2500 2500 2500 MHz MHz MHz MHz
K 62 26 30 1
Receiver Multicoupler
780 234 780 232 727 621 8 outputs 8 outputs 8 outputs 68 87.5 MHz 146 174 MHz 400 470 MHz
727 621
69
70
Page
Directional Antennas
Dimensions Clamps and Downtilt kits 72 74
Tools
Azimuth Adjustment Tool 79
Brackets
Bracket with Fixed Spacing Bracket with Adjustable Spacing 80 80
71
Mechanical Accessories
XPol Panel 88
A B C 1007 mm 2040 mm 2080 mm 1997 mm 1050 mm 1090 mm
72 9
33 C
B
110,5
64
18
Top view
317
72
193
72 64 9
Top view
258
103
73
Mounting Hardware for Directional Antennas VPol Panel 63 / 65 120 XPol Panel 65
Mounting clamps/Downtilt kit (order separately)
Type No. (Pair of clamps) K 61 14 01 K 61 14 02 K 61 14 03 K 61 14 04 K 61 14 05 733 695 Suitable for pipe masts of ... mm diameter Weight kg
40 95 2.6 60 116 2.6 116 210 4.0 210 380 7.2 380 521 10.2 Downtilt (to be used with a suitable pair of clamps for the individual mast diameter!) Downtilt Angle 0 22 0 11
Pair of clamps K 61 14 03
straight
elbow
74
Special downtilt kit for Eurocell Panel antennas with a weight greater than 25 kg and for XPol Panel for Tetra
Downtilt kit
Type No. Preferred range of use M10 supplied
850 10007
Panel antennas with a weight of 25 kg Panel antennas with attached mounting plates Downtilt kit without scale for universal use 5.9 kg Hot-dip galvanized steel Stainless steel
M8 supplied
90
Downtilt angle
Antenna height 1000 mm 2058 mm Downtilt angle 0 15 0 11 300 72
9
75
Mounting Hardware for Directional Antennas VPol Panel 115 Downtilt kits
Antenna Height: 974 mm 1934 mm
10 25 8 3
Mast diameter 28 64 mm 50 115 mm 110 220 mm 210 380 mm 60 115 mm 115 210 mm 210 380 mm 380 521 mm
Type No. *731 651 738 546 850 10002 850 10003 733 733 733 733 677 678 679 680
Weight Units per approx. antenna 330 g 1.0 kg 2.7 kg 4.8 kg 2.0 2.6 4.0 5.3 kg kg kg kg see sketch see sketch see sketch see sketch see see see see sketch sketch sketch sketch
9 1974 34
731 651
738 546
Use the downtilt kit together with the clamps mentioned above
Scale
76
12 15 69
Downtilt angle
Antenna Height 974 mm 1934 mm Downtilt angle 0 21 0 11 Type No. 737 973 737 975 Weight approx. 2.8 kg approx. 2.8 kg
Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm.
Eurocell Panels 3 Sector Panel Arrangement Mounting Hardware 3 Sector Clamp Kit / Pipe Mast with Flange Base
q q
Slim and unobstrusive design Nearly cylindrical optical appearance with small outer diameter
for Only els ll Pan e Euroc
742 033 120 114.3 mm 742 035 742 034 120 139.7 mm 742 036
2 x 3 sector clamp 2 x 3 sector clamp 2 x mounting support 2 x mounting support clamp clamp Material 3 sector clamp Hot-dip galvanized steel Hot-dip galvanized steel Mounting support Aluminum Aluminum clamp Screws Stainless steel Stainless steel Outer diameter (Dout) of the 3 A-Panel Arrangement 420 mm 441 mm Weight Clamp kit 3.0 kg 3.2 kg 3 sector clamp 1.4 kg 1.5 kg 64 0.5
60
B Torque 8 Nm
Bottom view without downtilt kit Type No. A B 742 033 114.3 88 742 034 139.7 100 all dimensions in mm C 217 236 D 207 228 E 49 49 F 45 45
Type No. Pipe diameter D according DIN 2448 Wall thickness pipe Pipe length Flange diameter Flange thickness S Hole circle diameter Number of holes Hole diameter Enclosed bolts thread x length Hot-dip galvanized steel Weight Material pipe mast Material flange base
6.3 mm 4 mm 3000 mm 3000 mm 210 mm 265 mm 14 1 mm 19 1 mm 170 mm 225 mm 6 6 18 1 mm 18 1 mm M16 x 100 mm M16 x 100 mm Quality min. 8.8 Quality min. 8.8 60 kg 55 kg S355 J2H (St 52-3N) DIN EN 10210-1 S235 JR G2 (RSt 37-2) DIN EN 10025
Maximum permissible load: According DIN 4131 and DIN 4132 Fatigue class K2
77
Use this mounting kit only for antennas less than 25 kg each.
Type No. No. of pieces Suitable for A-/C-Panels 65, 90 with a max. height Material: Clamp Screws Weight Mounting
850 10006
2 x brackets 2.6 m Hot-dip galvanized steel Stainless steel Approx. 3.3 kg Screws are supplied
34
640.2
640.2
R1
73
0.5
2800.5
Mounting Accessories (order separately) Clamps (only the listed clamps are allowed!)
Type No. 850 10002 850 10003 Description 1 clamp 1 clamp Remarks Mast: 110 220 mm diameter Weight Units per approx. antenna 2.7 kg 2 2
Please chose the fitting downtilt kit that you need, from the antenna datasheet.
78
Target object
Elevation compensation
Panel
262
F-Panel 33
equivalent for
A-Panel
F-Panel
199
F-Panel F-Panel
155 equivalent for
F-Panel
X-Pol-F-Panel
F-Panel
X-Pol-F-Panel
Instruction: Use a map to work out the angle between the designed antenna azimuth and target (church, building, mountain peak). Set this angle on the scale of the adjustment tool. Place the adjustment tool onto the antenna and tighten the clamping device. Use the telescope to aim at the target object, if necessary, use elevation compensation. Then rotate the antenna until the target object appears in the telescope. * Observe the position of the stopper when fitting the azimuth adjustment tool.
79
When mounted to the tip of a mast, the antennas described in this catalogue radiate horizontally in a circular fashion. However, they can also be mounted laterally to a mast by using an extension bracket. Depending on the spacing and the mast diameter, various types of radiation patterns can be achieved. (For further information please see the Technical Information part of our catalogue on pages 86 and 87)
mounting kit to pipe masts of 20 54 mm diameter. By means of mounting kit (supplied) to pipes of 55 mm 105 mm 55 mm 105 mm 105 mm 265 mm 105 mm 265 mm diameter
1015 mm
4 K 61 33
antennas with mounting kit to pipe masts of 20 54 mm 30 90 mm 50 94 mm diameter diameter By means of mounting kit (supplied) to pipes of 55 mm 105 mm 40 105 mm diameter diameter Hot-dip galvanized steel. 45 N (at 150 km/h) 100 N (at 150 km/h) 65 N (at 150 km/h) Double Bracket
740 mm 125 to 680 mm 245 mm 100 to 240 mm 40 x 40 mm 2 Pipe 76.1 x 2.6 mm free length 180 mm 40 x 40 mm 2 L 30 x 4 Pipe 70 x 4 mm free length 250 mm L 30 x 4
Attachment
125 to 680 mm
740 mm
fig. A
fig. B
fig. C
80
Type Kathrein Train Antennas a Solution also for Indoor Applications Antenna Systems with Panels K 52 32 2. . Examples of Radiation Patterns at 390 MHz with Combinations of Panels 741 517 Examples of Radiation Patterns at 390 MHz with Combinations of Panels 800 10252 Radiation Patterns for Side-mounted Omnidirectional Antennas Isolation Between Two Half-wave Dipoles Isolation of Two Vertically Stacked Panels K 73 30 2. Antenna Gain, VSWR / Reflected power VSWR-reduction / Mismatch loss
Page 82 83 84 85 86 87 88 89 90
81
Technical Information
Kathrein train antennas has been implemented on indoor systems all over the world. Advantages: Sophisticated and robust design based on a fiberglass radome. Because of this rugged radome design, the antenna is well protected against vandalism. Low profile broadband antenna with small optical appearance. Especially in lower frequency applications, indoor antennas may have an unhandy size. This is due to the fact, that the antennas normally use a halfwave lambda radiator. Example: TETRA 390 MHz, antenna length roughly 400 mm. Train antennas are based on quarterwave radiators resulting in conjunction with a special radiator design in very low lengths. The antenna 732 997 for the range of 380 412 MHz (see picture aside) is only 140 mm long! For a proper operation these antennas need an electrical counterweight or ground plane of a certain min. dimension. Mounting situation: The antennas has to be mounted on a conductive surface with dimensions according to the datasheet. This could be realized by a metallic sheet on the ceiling or directly by mounting the antenna on a metallic artificial ceiling. For a good contact one side of the antenna flange is not painted. Accordingly also the ground plane should be free of color in the area of mounting location. We strongly recommend to follow these specifications, otherwise the VSWR of the antenna will increase, destroying the performance of the antenna. Painting: The radome and base can be painted in any long-lasting color to match the surroundings. Suitable commercial paints consist of one or two components. The manufacturers instruction for use and processing must be observed. Paints with metallic effects or metallic components are not permissible.
82
140 mm
Arrangement
Technical Data 100 % rel. field strength corresponds to a gain* of 1 bay 2 bays 8.4 dB 8.2 dB 8.4 dB
10
3 0
Required components with conn. N female (without mounting kits): 2 antennas K 52 32 21, 2 junction cables K 62 21 3, 1 antenna transformer K 62 55 21 Spacing A 100 % rel. field strength corresponds to a gain* of 1 bay 2 bays 7.8 dB 8.5 dB 9.1 dB
10
3 0
Required components with conn. N female (without mounting kits): 2 antennas K 52 32 21, 2 junction cables K 62 21 3, 1 antenna transformer K 62 55 21 Spacing A 100 % rel. field strength corresponds to a gain* of 1 bay 2 bays 6.3 dB 7.0 dB 8.0 dB
10 dB
3 0
Required components with conn. N female (without mounting kits): 3 antennas K 52 32 21, 3 junction cables K 62 21 3, 1 antenna transformer K 62 56 21 Spacing A 100 % rel. field strength corresponds to a gain* of 1 bay 2 bays 4.8 dB 5.6 dB 7.0 dB
A 4
10 dB
3 0
Required components with conn. N female (without mounting kits): 4 antennas K 52 32 21, 4 junction cables K 62 21 3, 1 antenna transformer K 62 57 21 * ref. /2 dipole
58
27
3 0
3 0
dB
1 Bay
83
Examples of Radiation Patterns at 390 MHz with Combinations of Panels 741 517 (XPol)
Array
Technical Data
1
Distance A
100% rel. field strenght corresponds to a gain of 0.16 0.25 0.5 1.5 m m m m 9.85 9.95 9.45 9.55 dBi dBi dBi dBi
10 3 0
2
Distance A 0.32 0.5 1.0 2.0
dB
dB
100% rel. field strenght corresponds to a gain of m m m m 7.75 8.15 7.85 7.95 dBi dBi dBi dBi
A
3
10 3 0
A
Distance A 0.16 0.22 0.65 1.1
dB
100% rel. field strenght corresponds to a gain of m m m m 5.85 5.75 6.55 6.35 dBi dBi dBi dBi
10 3 0
4
Distance A 0.32 0.5 0.8 2.1
dB
100% rel. field strenght corresponds to a gain of m m m m 6.15 7.15 7.65 7.35 dBi dBi dBi dBi
A
10 3 0
84
Examples of Radiation Patterns at 390 MHz with Combinations of Panels 800 10252 (VPol)
Array
Technical Data
1
Distance A
100% rel. field strenght corresponds to a gain of 0.25 m 0.5 m 1.5 m 9.55 dBi 9.35 dBi 9.85 dBi
10 3 0
2
Distance A 0.5 m 1.0 m 2.0 m
dB
dB
100% rel. field strenght corresponds to a gain of 8.05 dBi 7.75 dBi 8.35 dBi
A
3
10 3 0
A
Distance A 0.16 0.22 0.65 1.1
dB
100% rel. field strenght corresponds to a gain of m m m m 5.45 5.75 6.95 6.95 dBi dBi dBi dBi
10 3 0
4
Distance A 0.5 m 0.8 m 2.1 m
10 3 0
100% rel. field strenght corresponds to a gain of 6.85 dBi 7.35 dBi 7.45 dBi
A
dB
85
Examples of horizontal radiation patterns for different mast diameters where A = 0.25 ; 0.5 ; 0.75 . Examples also apply for antenna K 75 29 2 .
Distance A:
Mast diameter
Tubular mast Antenna
A
60 mm
10 dB
3 0
160 mm
A = 0.25 A = 0.5 A = 0.75
10 dB dB
dB
3 0
250 mm
10 dB
3 0
600 mm
10
3 0
Triangular lattice mast Antenna Triangular lattice mast with side length of 500 mm
10
3 0
86
Isolation between two half-wave dipoles, vertically polarized and positioned vertically in line above each other on one common mast.
dB 50 Koppeldmpfung Isolation 45 40 35 30 25 20 15 10 0,5 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 1,9 2,0 2,1 2,2 2,3
/4
d s
Isolation Koppeldmpfung
40 38 36 34 32 30 28
52 50 48 46 44
7 8 9 10
15
20
20
30
s
40 50 60 80 100 120
87
54
B 45
Isolation
40
35
1000
1500
2000
Distance A/mm
88
15 14
G / dB = 10 log P1 P2
13 12 11 10 9 8 9 10 11 12
Gain in dB
40 3.0 2.5
Voltage Standing Wave Ratio (VSWR)
30
27 26
24
22
20
18
16
14
12
10
= 1+r = 10+ 1-r 10ar (in dB) = - 20 log r s P (in %) = (10 r)2 = P (in %) = s ar
100 100ar/20
Reflected power . 100 Forward power = VSWR, r = Reflection coefficient = Return loss
1.2 1.1 1.0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.06 0.8 1.0 0.12 2 3 4 5 6 8 10 0.3 15 0.35 0.4 20 P (in %) = Reflected power Forward power
89
Cable loss
1.5
1.4
1.3 B Feeder cable A 1.0 1.1 1.2 1.3 1.4 1.5 1.2
1.1
0 dB
1.6
0.5 dB
1.6
3.0 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.2 0.4 0.6 0.8 1.0 1.2 Mismatch loss in dB
90
Technical Information:
Fax: +49 80 31 1 84-9 73 E-Mail: antennas.mobilcom@kathrein.de
Internet: www.kathrein.de KATHREIN-Werke KG . Telephone +49 80 31 1 84-0 . Fax +49 80 31 1 84-9 91 Anton-Kathrein-Strae 1 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany
9987.206/1004/1.5/ZW/HA
Subject to alteration.