Académique Documents
Professionnel Documents
Culture Documents
(without price)
CE-3700 CE-3750
DEC, 1994
(EX-278)
(EX-279)
INDEX
CONTENTS Page 1. SPECIFICATION .......................................................................................... 1 2. OPTION SPECIFICATIONS ......................................................................... 3 3. INSTALLATION ........................................................................................... 3 4. INITIALIZE.................................................................................................... 4 5. MAJOR COMPONENT ................................................................................ 6 6. BLOCK DIAGRAM ....................................................................................... 7 7. CIRCUIT EXPLANATIONS .......................................................................... 8 8. DISASSEMBLY / ASSEMBLY METHOD .................................................. 12 9. DIAGNOSTIC OPERATION ....................................................................... 13 10. PROGRAMMING THE CE-3700 SERIES CASH REGISTERS ................. 17 11. OPERATION .............................................................................................. 19 12. ERROR CODES ......................................................................................... 20 13. IC DATA ..................................................................................................... 21 14. PCB LAYOUT ............................................................................................ 22 15. CIRCUIT DIAGRAM ................................................................................... 23 16. PARTS LIST ............................................................................................... 33
Product introduction This machine CE-3700(EX-278) is a succession machine for CE-3400(EX-253). The simultaneous boot model is EX-279. EX-278: The drawer not separation type. EX-279: The drawer separation type. The Rom/Ram is the internal organs.
1. SPECIFICATION
1-1. Product Operating temperature: Operation air moisture: Storage temperature: Storage air moisture: Bombardment strength: 0 C ~ 40 C 10 % ~ 90 % -25 C ~ 65 C 10 % ~ 95 % To add bombardment from 10 high cm by single support, and there isnt the problem.
1-2.
Package status Storage temperature: Storage air moisture: Vibration strength: Bombardment strength:
-25 C ~ 65 C 10 % ~ 95 % 1.5 G To add bombardment from 60 high cm by single support, and there isnt the problem.
1-3.
Accessory specifications Roll paper: Stamp logotype: Ink for supplement: Ink roll: Dust cover: Printer CR-812A-009-14-001A: CR-812A-009-15-001A:
P-4575 (EX-P-4574), 45 X 12 X 30 D CSP-2030ASA-2 Super Ink KC IR-92 (EX-INK-IR-92-OP) Only 1 part neighborhood
1-4.
Printing type: ring select mode Output sheet number: 2 Chart specifications Paper width: 44.5 0.5 mm Maximum paper diameter: 83 mm Maximum paper thickness: 0.06 ~ 0.085 mm Materials: Regular paper Inking: Ink roll Validation Print specifications: Yes Sensor: No Paper cut: Manual Stamp Color: Purple Seal side dimension: 30 mm (W) X 20 mm (H)
1-5.
The durability specifications Switch Key board switch: Control lock: Operation key Feed switch Receipt on/off switch Reset switch Drawer: Printer MCBF: Ink roll Stamp Ink: mechanism:
5,000,000 times 20,000 times 100,000 times 5,000,000 times 10,000 times 100,000 times 1,000,000 times 2,000,000 line 400,000 line 50,000 times 500,000 times
1-6.
Electric specifications Power consumption Area In action Max. In holding Min. Power off 120 V 0.40 A 0.09 A 0.08 A 220 V 0.20 A 0.05 A 0.04 A 230V 0.20 A 0.05 A 0.04 A 240V 0.20 A 0.05 A 0.04 A
1-7.
Vanadium Lithium secondary battery Model: VL3032/IF2 Guard period: 90 days (25 C) In perfection charge status Galvanic cell life expectancy: 5 years Recharge time: 48 hours in secondary battery CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufactures instructions.
1-8.
1-9.
Electric power supply for an emergency (B-6) Operating hour: 3 hours Driving condition Processing time per customer one person: 60 sec./ person Purchase item number: 10 item / person 1 item registration amount of money number of digits: 4 digits / item The handling number of people for 1 hour: 30 person /hour Recharge time: 8 hours
2. OPTION SPECIFICATIONS
2-1. 2-2. 2-3. 2-4. Ink roll: Waterproofing cover: Roll paper: IR-92 WT-70 P-4575 (451275D)
The following parts are necessary to add B-6. No. Q1 ZD1 D6,D7 C5 R2,R3,R5 R1 Code No. 2200 3577 2310 8879 2301 0011 2804 5476 2600 7313 2600 5612 6221 4218 Parts Name Transistor Zener diode Diode Electrolytic capacitor Carbon film resistor Carbon film resistor Connector sub assembly CVK-S2/-L2/-LLL2/-FS2 Super ink K Specification 2SA1015(GR,O,Y) RD18EB1 1S2471 50RE47 R-25-10K-J R-25-2K-J E311294-1(#22) Q'ty 1 1 2 1 3 1 1
2-5. 2-6.
3. INSTALLATION
Connection is done of earth-line of drawer and main frame like lower chart.
4. INITIALIZE
By Initialize code Init. A: The format is done of EEPROM, and, without it is read, and Init. Code is written in. Init. B: The data is read from EEPROM. 4-1. MAC To hang initial start-up of CPU and peripheral device, and All Clear makes memory. When there is Data backed up by EEPROM, by Initialize code, to develop it on Memory top. Operation Power off Display Printing
To continued pushing J-feed button, and To set the MODE switch to Program.
Header printing
0000000000
D1 ~ D5
D1D2D3D4D5
#-2
P1
Input value D1 ~ D5 D1 0: YYMMDD 1: MMDDYY 2: DDMMYY 1: General 2: US 3: General 5: Canada Department No.
D2
D3,D4 D5
(Add2, DDMMYY) (Add2, MMDDYY) (Add3, DDMMYY) (Add2, MMDDYY) General 15 US 30 Clerk specification Switch: Password No.:
4-2.
Auto or Reset switch initialize Operation To push Reset SW. or Power on In Low batt. Display 0000000000 Printing
D1 ~ D5
-- XXXX --
#-2 Input value D1 ~ D5 D1 0: YYMMDD 1: MMDDYY 2: DDMMYY 1: General 2: US 3: General 5: Canada Department No.
P1
D1D2D3D4D5 ---------------
D2
(Add2, DDMMYY) (Add2, MMDDYY) (Add3, DDMMYY) (Add2, MMDDYY) General 15 US 30 Clerk specification Switch: Password No.:
Operation code with Init.B is set up as with settlement in 00000. Flag clear
To do Initialization of work memory, and make the operation sequence with the latest status. Operation Display Printing Power off
To continued pushing R-feed button, and To set the MODE switch to Program.
Header printing
-- XXXX -D1D2D3D4D5 P1P2P3P4P5P6P7P8 X1X2X3X4 M1M2-D1D2-Y1Y2 --------------Password for P1~P8 Password for X1~X4: X2/Z2 M1M2D1D2Y1Y2
#-2
P1
5. MAJOR COMPONENT
CPU Ram Printer Drawer Model MCBF USA Canada UK Other Countries Germany CPU Pin Description
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 37 36 35 34 33 O O O O O Port No. 94 93 92 91 90 81 80 27 26 25 24 23 22 21 20 74 73 Name FIP6 FIP5 FIP4 FIP3 FIP2 FIP1 FIP0 SCK0 SO1 SI0 BUSY STB SCK1 SO1 SI1 In/ Out O O O O O O O I/O I/O I/O I/O I/O I/O I/O I/O O O Description Display Digit Signal (Dg7) Display Digit Signal (Dg6) Display Digit Signal (Dg5) Display Digit Signal (Dg4) Display Digit Signal (Dg3) Display Digit Signal (Dg2) Display Digit Signal (Dg1) Power (VDD) Data 7 Data 6 Data 5 Data 4 Data 3 Data 2 Data 1 Data 0 Reset Signal CE(Ram Chip Enable) R/W(Ram Write Enable) Analog electric potential of AD converter (Gnd) Key Input Signal (KI7) Key Input Signal (KI6) Key Input Signal (KI5) Key Input Signal (KI4) Key Input Signal (KI3) Key Input Signal (KI2) Key Input Signal (KI1) Key Input Signal (KI0) Analog electric power supply of AD converter (Vcc) Reference voltage input of AD converter (Gnd) Clock Terminal Clock Terminal Analog electric potential of AD converter(Gnd) System Clock 4.19MHz System Clock 4.19MHz EEPROM CE Buzzer Decoder CE DW1&2 Journal Common Signal Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 105 104 103 102 101 100 97 96 95 FIP15 FIP14 FIP13 FIP12 FIP11 FIP10 FIP9 FIP8 FIP7 O O O O O O O O O Port No. 32 31 30 3 2 1 0 70 71 72 127 126 125 124 123 122 121 120 117 116 115 114 113 112 111 110 107 106 FIP33 FIP32 FIP31 FIP30 FIP29 FIP28 FIP27 FIP26 FIP25 FIP24 FIP23 FIP22 FIP21 FIP20 FIP19 FIP18 FIP17 FIP16 Name TO2 TO1 TO0 INTP3 INTP2 INTP1 INTP0 In/ Out O O O I I I I O O O O O O O O O O O O O O O O O O O O O Description Receipt Common Signal Auto cutter Stamp Drawer sensor Key scan timing plus Power Down Printer Gnd for Vpp (IC) Address decoder (A12/D0) A13/Decod1 A14/Decod1 Power (VDD) Printer Head (HD8) Printer Head (HD7) Printer Head (HD6) Printer Head (HD5) Printer Head (HD4) Printer Head (HD3) Printer Head (HD2) Printer Head (HD1) Printer Head (HD10) Printer Head (HD9) Printer J-feed Printer R-feed Printer Motor Key Common Signal (KC9) Display Digit Signal / Key Common Signal (SGdb/KC8) Display Digit Signal / Key Common Signal (SGtr/KC7) Display Digit Signal / Key Common Signal (SGg/KC6) Display Digit Signal / Key Common Signal (SGf/KC5) Pull Down electric potential for Fip (VN) Display Digit Signal / Key Common Signal (SGe/KC4) Display Digit Signal / Key Common Signal (SGd/KC3) Display Digit Signal / Key Common Signal (SGc/KC2) Display Digit Signal / Key Common Signal (SGb/KC1) Display Digit Signal / Key Common Signal (SGa/KC0) Key Scan Timing Plus Display Digit Signal (Dg10) Display Digit Signal (Dg9) Display Digit Signal (Dg8)
UPD78044AGF080-3B9 LC36256PLL 256K bit SRam CR812A-009-15-001A 2,000,000 lines DL-2416 D-15TC-A55SP-1* DL-2351 D-15TC-A54SP-1* DL-2751 D-15TC-A84SP-1* DL-2350 D-15TC-A54P-1* DL-2750 D-15TC-A84P-1* DL-2752 D-15BC-A84S-1*
17 16 15 14 13 12 11 10
I I I I I I I I
6. BLOCK DIAGRAM
Standard
CPU
Option
Printer (CR812A) Main Display (10 columns) Pop-uo Display (10 columns) RAM (32K byte) EEPROM (512 byte) Key board Drawer
Compulsory Drawer (USA, Canada,Germany, UK)
Multi Drawer
Buzzer
Power Supply
7. CIRCUIT EXPLANATIONS
7-1. Power supply circuit
1) Diodes rectification bridge By diodes rectification bridge, alternating voltage is converted into DC voltage, and the electrical voltage is done filtering of by Capacitor C4. 2) Power supply circuit for B-6 The electrical voltage which puts in resistor 3 when line voltage includes anomaly changes, and transistor Q1 becomes on status, and CS signal is done outgoing of by this, and VP is supplied than Power supply B-6. Note: The component for connection isnt equipped with in plant shipping. (service arrangement) 7-2. DC/DC converter circuit
2SD721(Q2) is Power voltage control transistor, and electric power supply is supplied in DCDC converter with 2SC3303(Q3). 2SC3303(Q3) does a work as oscillator. The frequency of 2SC3303(Q3) is controlled by signal done feed back of through RD27EB1. 7-3. Electrical voltage value in check point Vc Min: 23 V Max: 42 V AC Vp 20 V 2V DC Vcc/Vdd 5V 0.3 V DC Vns 32 V 10% DC Vs 27 V 10% DC Vf 4.75 V 7% AC
Rated output electrical voltage Output voltage drift range Output voltage drift range
7-4.
Reset circuit
The voltage fluctuation of VDD is controlled of IC10 (S-80727AN). CPU is done Reset by pushing Reset Switch or drifting VDD.
S-80727AN 2 1
Vdd
CPU
Reset SW 17 Reset
7-5.
EEPROM is Rom that write / erase is possible electrically. BR93LC46A is a non- volatile register, and serial data of 16 bit can be memorized with 64 register. CPU CS SK DI DO 1 2 3 4 36 14 15 16 EEPCS AD2 AD1 AD0 EEPRom
Chip select Serial data clock Serial data input Serial data output 64 words X 16 bits 1,024 bits
[ Data reading procedure ] When the CPU read the data of EEPROM, CPU send the CS signal and SK signal to EEPROM. Then CPU send the address to EEPROM, and then EEPROM return the data to CPU.
CS
SK
DI
Address
DO
[ Data writing procedure ] When the CPU save the data to EEPROM, CPU sends the CS and SK signal to EEPROM. And CPU send the address and data to EEPROM from pin No. 15. When the EEPROM writes the data, EEPROM outputs the busy signal form DO terminal to CPU. After finish writing, EEPROM outputs the ready signal from DO terminal to CPU.
Status
CS
SK Address DI
READY(H)
Data
DO
High Impedance
BUSY(L)
10
7-6.
13.6us
3.95us
11
12
9. DIAGNOSTIC OPERATION
9-1. Start-up method By the next operation, EX-278 enters Test mode. 1) 2) 3) 4) 5) Mode switch off. To continued pushing J-feed button. To set the Mode switch to Program. To release from the J-feed button. To input 9 9 9 9 9 0 0 0 0 0 #2 Printing out 00-00-00 00:00 0000 <Feed> -- x x x x ----------------X: Version No. or - - - -
The cancellation of test mode do INIT. 9-2. Description 1) Key code representation: expect Value number, Clear and Feed button. 2) Various switches status display 3) Testing for Display, Print, DRW, RAM: Value number 1 column + #2 4) Testing for E2PROM: Value number 1 column + #2 Key code representation
9-3.
C 056 7 4 1 0
13
9-4.
0: Fixed For Taiwan 1: Journal mark sensor 0: Except it For Taiwan 1: Receipt mark sensor 0: Except it 1: Fixed Non taxable pad For Japan 0: Taxable (pat short) 1: Non-taxable (pat open) Drawer sensor 0: Open 1: Close Journal near end 1: Near end 0: Out of sense Receipt off switch 0: Receipt on 1: Receipt off Key clerk 0: Non 1~9, A~F:Clerk code (Hexadecimal representation) Push clerk 0: Non 1: Clerk 1 2: Clerk 2 3: Clerk 3 4: Clerk 4 Mode representation 1: PGM 2: RF 3: REG1 4: REG2 5: X 6: Z 7: X2Z2 8: Off 0: Disconnected
14
9-5.
Print, Display, Drawer and Ram testing to do a various test by value number key. The following code print by all means then. 1# 3# 4# 5# 96 # 8# 9# 1 #2: All testing 3 #2: E2PRom r/w testing 4 #2: E2PRom reading testing 5 #2: Ram reading testing 96 #2:E2PRom Initialization 8 #2: Printing testing 9 #2: Clock testing
1)
#2
All lighting, Ram, R/W, setting the time and date, drawer opening, printing, receipt(Japan) stamp and receipt issue.
All lighting
Receipt printing Beeping one shot buzzer on Setting date and time: Date: Dec. 31st 1994 Time: 23:59 Drawer open: Drawer No.1 and No.2 are opened. Test printing: To do the following print The first line does print in receipt, journal independence. The second line does print at receipt, journal same time. 01234567FS@ 01234567FS@ Receipt stamp: (only japan) Receipt issue: Testing display: To do indication as follows till key or a state changes 1234567890
15
2) 3 #2
This does R/W test of testing area of E 2PRom during single word, and, at the time of normal, does normal termination print. To do the following printing then breaking -------8
Abnormal end:
Receipt printing Beeping one shot buzzer on 3) This does read only test of testing area of EEPRom during single word. This test is continued till off mode or electric power supply enters it. To do the following printing then breaking -------8
#2
Abnormal end:
Receipt printing Beeping one shot buzzer on 4) Read only test . Outside Ram(0000H~7FFFH) read in testing The address comparing data which comes under it = (A0-A7) + (A8-A14) This test is continued till off mode or electric power supply enters it. To do the following printing then breaking -------2
#2
Abnormal end:
Receipt printing Beeping one shot buzzer on 5) Blanking (OFFH writing) of data in EEPRom entirely. Time of day, a date are turned into zero entirely.
#2
6)
#2
7)
#2
Time of day representation testing Time of day indication is done till clear Key 23 -59 12
16
You should perform the procedure shown blow as the first step of programming. Notice that the flowchart ends with an arrow on the bottom. This indicates that you should continue to the next programming procedure for the mode you specify. Procedure
Program
Enter a number to specify the program mode (1 ~ 4) Press the Sub total key. The display should show the letter P followed by the program number you specified (i.e. P3 = Program mode 3). Press the # 1 key. Enter 4-digit password. Skip this step when the password is not programmed. Press the Sub total key.
CA/Amt Tend
Sub Total
Note: Program mode 1 is automatically set when the Mode switch is set to Program from another setting. Recommended programming sequence Generally, you should perform programming in the following sequence. Note that we recommend you check what is programmed for each mode before proceeding to the programming operation.
17
1 Use Program 4 to read the assignment of functions to programmable keys and then make changes. 2 Use Program 3 to read the definition of machine features and key functions and then make changes. 3 Use Program 1 to read programming of time, date and unit price, amounts, rates, etc. and then make changes. 10-2. Using the worksheets The worksheets included in this manual for Program 3 and Program 1 help to make your programming simple and accurate. We recommend that you fill out the pertinent worksheet before attempting actual programming. 1) Carefully read each definition and specify a selection. Each definition is following by a Specification column which contains numeric values(Usually to indicate a simple YES or NO answer). Determine the correct value according to your need and enter it in the Selection column to the right. 2) Total each set of selections to calculate each program code digit. Three selections(a,b,c) make up a set. Add up each set of selections and fill in the totals in the Program code column for data items D8 through D1. 3) Program the feature or function. Be sure that you have filled in all of the selections and program code digits for the entire worksheet, and follow the procedure noted for the feature or function you are programming. 4) Check the printed program receipt against the worksheet. Perform program read operation in each program mode to print setting which you have programmed, to check then against the worksheet. We recommend that you do so and keep a copy on record to help out should it become necessary for you to change the program. 10-3. Clearing a machine lock up If you make a mistake in operation, the cash register may lock up to avoid damage to programs and preset data. Should this happen, you can use the following procedure to clear the lock-up without losing any memory data. Procedure Off Set the Mode switch off.
Press receipt feed key RECEIPT FEED
Release the
key.
Sub Total
You should see FFFFFFFFFF on the display. If 10 of Fs are not shown on the display or if another character is shown, immediately set the mode switch to OFF and start from the beginning of this procedure. IF you dont see FFFFFFFFFF on the display, do not press the Sub total key. Finalize the procedure.
18
11. OPERATION
Operation of your cash register is designed to be simple enough to master without any special technical knowledge. Anytime you make a mistake in operation, an error tone sounds and further operation becomes impossible to protect your valuable data. Whenever this happens, you can resume normal operation after pressing the C key. Printing of the symbol can be programmed when the C key is operated in the REG1, REG2, and RF modes. The number of the C key operations can also be programmed for printing on the general control Read/Reset reports. As you become familiar with the key layout of the cash register, you may find that your keyboard entries are getting ahead of the receipt and journal printer. But you never need to worry that the cash register will miss anything. A built-in key input buffer memory holds entries for up to eight keys to let the cash register catch up when you slow down or stop. Another thing you dont need to worry about is power outages. Your register features built-in rechargeable lithium batteries that return such information as program data, registration records, data, item, and consecutive number. These and other features and functions of the CE-3700 series electronic cash register make it a welcome addition to any retail environment. Performing daily cash register operations The actual operations that you perform with your cash register will depend in the nature of your own business. The following outline shows the most common operations in the order they are usually performed. Operation Confirm that enough receipt and journal paper are present, and load new paper rolls if necessary. Read daily totals to confirm that the RESET operation was performed for the previous day's totals. Preset unit prices for department keys, PLUs and function keys if necessary. Set the MODE switch to REG and identify a clerk using a clerk secret number. Check the date and time set on the cash register. Register transaction. Normal sales Received on account and paid out Returns Perform READ and RESET operation as required, after counting the money in the cash drawer and registering the amount. Read daily sales totals. Read periodic sales totals Reset daily sales totals Reset periodic sales totals Remove the printed journal, reports from the cash register. Set the MODE switch to OFF and remove the key. Empty the cash drawer and leave it open. Carry the journal, reports and cash to the office. Mode switch OFF X1 Program REG1/REG2 REG1/REG2 REG1/REG2 REG1/REG2 REG1/REG2/RF
1 2 3 4 5 6
8 9 10 11
19
E 02 E 03 E 04 E 08 E 09
E 11
E 16 E 27 E 31 E 32 E 33 E 35 E 38 E 41 E 94 Remark:
Denoted * which these error only occur when certain function are programmed as compulsory prohibited.
20
13. IC DATA
1) TC74HC138
2) TC74HC174
3) TC74HC367
21
C1 C4
D6 D7
B-2
CA2
C2
R5
C6 C5 ZD2
WARNING - FOR CONTINUED PROTECTION AGAINST FIRE HAZARD. D13 REPLACE ONLY WITH THE SAME TYPE AND RATING OF FUSE.
DCSI
B-6
C-1 C13
R6
CA3
D15
C10 J-1
31
D20
E-2
A E D19 C
VCC
VDD
CN4
L-1
IC3 BA12003
Q7 E
CN8
D34
R33
BZ1 B
B-19
C-13
C-14
C31
C-12
Q5
R40 B-16
X2
C24
B-20
D35 ZD5
1 CN10
C-10
C30 R53
B-18 C-11 R46 D-12 J-14 D-14 D-15 D-16 R62 C-42 B-24 IC9 BA10393 R51 R52 D-13
D-8
C-9 C26 2
IC13 74HC174
C45 LC36256PLL-10/12/15
C39 DW2 BR R56 R 1 CN12 B E Q14 R57 D38 R58 C40 B-21 R59 R60 R61 IC11
H-3
BK
R63
E-7 C38
C41
R55
C-43
IC12
C46
Q15
22
B-30
C-17
B Q13 E
C37
C44
B-27 B-28
D-18
CN5
CN1
B-6
POWER TRANSFORMER
FFC 10PIN
3
PRINTER CR812A 31PIN 32PIN
FFC
E278-E2-1
PC
VCC
PC PC
min 1.5S
4
2PIN
4
RST 18PIN E278-E4 FPC CPU-CLK 300mS
OPTION E278-1
3PIN
3PIN
3PIN
BATTERY
DRAWER
DRAWER
OPTION
6
RECEIPT JOURNAL FEED FEED RECEIPT VALID X RECEIPT JOURNAL CLK# FEED FEED RECEIPT VALID
X / FOR
DATE TIME
DATE TIME
OPEN
RC PD
CR 1 CR 2
CHK TEND
OPEN
6 5
12 11 10 9 8 7
18 17 16 15 14 13
24 23 22 21 20 19
30
RC PD T/S1 T/S2
5 10 15 7 4 8 5 2 9 6 3 4 3 2 1 9 14 8 13 7 12 6 11
29 CR 1 CR 2 28
NS #
CH
NS # %
PRICE
7 4 1
8 5 2
9 6 3
4 3 2 1
CH
SUB
CHK TEND
% RF
PLU
ERR.CORR
SUB TOTAL
27 TOTAL MD/ST 26 25
CA
AMT TEND
PLU RF
ERR.CORR
CA
AMT TEND
CANCEL
0 00
CANCEL
0 00
F
23
2
POWER TRANSFORMER
B-6 E278-E2-2 OPTION 3PIN FFC 10PIN FFC 12PIN MODE-KEY VCC FFC 31PIN 32PIN
PC
2
15V VP
3
PRINTER CR812A
2PIN E278-E2-1
PC
3
15mS 40mS min 1.5S
PWD
E241 -E3-2
RESET SW 2PIN
NEAR END SENSER
RECEIPT ON/OFF
3PIN
5PIN
3PIN
3PIN
KEY CLERK
RECEIPT JOURNAL FEED FEED RECEIPT VALID
6
OPTION
DATE TIME
OPEN
RC PD
CR 1 CR 2
CHK TEND
5 10 15 7 4 8 5 2 9 6 3 4 3 2 1 9 14 8 13 7 12 6 11
NS # % RF
PLU
ERR.CORR
CH
SUB TOTAL
CA
AMT TEND
CANCEL
0 00
F
24
CN6 IMSA-9604S-32C
32 31 23 24 25 26 27 28 29 30 2 9 8 5 6 3 13 14 15 16 17 18 19 20 21 22 7 12 11 10 4 1
VDD KC0 KC1 KC2 KC3 KC4 KC5 KC6 KC7 KC8 KC9 C12 TFC103 VF2 CN13 B28-EH VP R13 56K C101 C8 ZD5 R42 15EB3 D35 Q12 2SC945 R41 50V1 C26 R43 56K
+
CN7 IMSA-9604S-18C 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 KI2 KI1 KI3 KI4 KC1 KC2 KC3 KC4 KI0 KI5 KC5 KC6 KC0 KC7 KI6 KC8 KC9 KI7
MCOM D21
PCOM CD7 CD6 CD5 CD4 CD3 CD2 CD1 CD0 VF1 SD SE SG SF SH DG9 DG8 DG7 DG6 DG5 DG4 DG3 DG2 DG1 DG0 SCOM SA SB SC SDP VF2
OTP ONLY
VDD
VF1
100 X8
RSTAMP
1K
D34 VP
D43
R33 CRH100-1 VP D39 003 D40 002 D41 001 D42 000 KCOM D1 CD7 PCOM
VCC Q15
1 2
100K
VP 1SR35-100 C101 C27 RA3 RGLD8X563J CA7 CNB8X101K GND R26 1.8K GND GND Q4 D27 Q6 2SC945 2SD2015 R28 C3 C101 4.7K R27 10K R29 1K Q5 2SD2015
1SR35-100
RA1 RGLD8X222J
P95 P96 P97 P100 P101 P102 P103 P104 P105 VLOAD P106 P107 P110 P111 P112 P113
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
GNDP
SF SG SDP SH
SA SB SC SD SE
CA5 CNB8X221K
5 4 3 2 1
Q7
VCC
D13
CD7 KCOM VN
1S2471 BA12003
56K 56K VN GND 56K 56K R30 D28 56KGND C31 C101
IC8 74HC367 IC8 IC8 IC8 IC7 IC7 IC7 IC7 C16 R32
TAIWAN CN8
VCC
VCC IC14 74HC174 1 16 CLR VCC 2 A6 10 A11 Q6 Q1 3 AD5 AD0 11 D6 D1 14 AD4 AD1 6 D5 D2 15 A10 A7 7 Q5 Q2 4 AD3 AD2 13 D4 D3 5 A9 A8 12 Q4 8 Q3 9 GND CLK C48 C49 TF103 IC13 1 A0 10 AD0 11 AD1 6 A1 7 AD2 13 A2 12 8 GND
VDD VDD
2 1 VCC R48 10K R47100K IC9 BA10393 +5 7 6 C29 C102 STAMP GND ACUT RCOM C30 C101
GND 100
VDD GND
C101
2 3
6 7
2 3
S-80727AN IC10 2 3 1
10
10
4 RFEED 64 JFEED 63 HD9 62 HD10 61 HD1 60 HD2 59 HD3 58 HD4 57 HD5 56 HD6 55 HD7 54 HD8 53 52 51DECD0 50DECD1 49DECD2 48 47TP 46 45 DWS 44 43 42 41 TF104 5 3 6 4
GND VDD VDD LC36256PLL-10/12/15 C42 TF103 DECD2 1 A14 VCC 28 27 DECD0 2 A12 WE A7 3 A7 A13 26 DECD1 A6 4 A6 IC12 A8 25 A8 5 A5 A9 24 A9 VDD 6 A4 A11 23 A11 GND 7 A3 OE 22 A2 8 A2 A10 21 A10 A1 9 A1 CE 20 A010 A0 I/O7 19 AD7 AD011 I/O0 I/O6 18 AD6 AD112 I/O1 I/O5 17 AD5 AD213 I/O2 I/O4 16 AD4 GND 14 VSS I/O3 15 AD3 R51 10K C44 C101
P13 P12 P11 P10 AVDD AVREF XT1 XT2 VSS X1 X2 P37 P36 P35 P34 P33
1 2 3 4 5 6 7 8 AD7 9 AD6 10 AD5 11 AD4 12 AD3 13 AD2 14 AD1 15 AD0 16 17 CE 18 19 20 KI721 KI622 KI523 KI424
P94 P93 P92 P91 P90 P81 P80 VDD P27 P26 P25 P24 P23 P22 P21 P20 RESET P74 P73 AVSS P17 P16 P15 P14
IC6
PD78044
P114 P115 P116 P117 P120 P121 P122 P123 P124 P125 P126 P127 VDD P70 P71 P72 IC(VPP) P00 P01 P02 P03 P30 P31 P32
GNDP IC5 11 IC3 15 IC4 10 IC4 12 IC4 14 IC4 16 STAMP JFEED RFEED JCOM JHD1 JHD2 JHD3 JHD4 JHD5 JHD6 JHD7 JHD8 JHD9 JHD10 MOTOR RCOM RHD1 RHD2 RHD3 RHD4 RHD5 RHD6 RHD7 RHD8 RHD9 RHD10 ACUT TP C15 C101
R38 10K 5 6 2 4 7 1 IC5 6 IC3 12 7 IC2 11 5 IC2 13 3 IC2 15 1 IC3 10 4 VP R34 16 10K G9 Q11 IC3 11 IC2 10 IC2 12 IC2 14 IC2 16 IC3 13 C22 C101
C101
C102
C37
PWD
X1 CST4.19MGW DECCE
C101
C47
R62
56K
R36
3.7K BZ1
IC8
VP
330K
R54
14
C32 C-002RX
R40
IC5
74HC174 16 CLR VCC 2 A5 Q6 Q1 3 AD5 D6 D1 14 AD4 D5 D2 15 A4 Q5 Q2 4 AD3 D4 D3 5 A3 Q4 Q3 9 GND CLK VCC GND 8 7 6 5 C41 TF103
16V100
C18 C34
+
VP
GND 2 C21
EEPCE IC5
BUZZ
C33 C120
X2 C46
D38
GND GND R46 C40 C39 C38 8.2K C101X3 P53 56K
R56 10K
GNDP Q14
R57
GND GND
TF103
GND
GND
1.8K 2SD1853
1 2 3 GNDP
BR93LC46A
C43
PKM22EPP-2002 RSTAP GND Y6 KCOM 9 Y7 Y5 PCOM 10 G1 Y4 MCOM 11 G28 Y3 LE2 12 G2A Y2 LE1 13 C Y1 14 Y0 B VCC 15 VCC IC15A 16 C36
VCC 10KX3
1SR35-100
1SR35-100
C46 C101
GND
R63
D33
D36
56K
R35 2SB926 VP 4.7K GND C23 2SA1015 VP 12 15 D32 C20 R37 15 C101 C101 1SR35-100 GNDP 14 10K 2SB926 10 UL-TSCR-0.8A 2SA1015 VP Q8 F2 Q13 1 13 1SR35-100 Q10 R55 2 3 1.8K VCC VP 2SD1853 C101 74HC367 IC8 4.7K
6
BK BR R
BK BR R
1
VP 1 VP CA1 CNB5X101K CA2 1 CNB8X101K VP CA3 1 CNB8X101K VP CA4 1 CNB3X101K
1
VP HBLB31-S2J CN1 STAMP 1 JFEED 2 RFEED 3 JCOM 4 JHD1 5 JHD2 6 JHD3 7 JHD4 8 JHD5 9 JHD6 10 JHD7 11 JHD8 12 JHD9 13 JHD10 14 15 MOTOR16 RCOM 17 RHD1 18 RHD2 19 RHD3 20 RHD4 21 RHD5 22 RHD6 23 RHD7 24 RHD8 25 RHD9 26 RHD10 27 ACUT 28 29 TP 30 31 TFC103 C2 BA10393 8 VCC 74HC367*2 VCC VP IC9 4 GND 8 C28 TFC103 GND GND VP BA12003*3 BA12003 VP GND C17 C19 TFC103 TFC103 5 4 3 2 1 IC7 IC8 KEY CLERK J-Y7541 16 1 2 RESET SW JPM1030-0101
2 3 4 6 7 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 2 3 4
VP
3
1 2 3 BATTERY VL3032/1F2
IC5
TFC103
VCC
D8 1SR35-100A
2SD721 WITH HEAT SINK OSH-3040-SP
GNDP
GNDP
D2 1SR35-100A VC
GND
Q2
D6 1S2471
D5 1SR35-100A
5
C1 TFC103
5
VFS2 VNS
50V10 C13
Q3
CN2 1 2 B2P3-VH
R4 35V2200 C7 R50-1.8K
TFC332 100
7 D17 1SS83
50V100 R11 R10 C14 33K
VS
D3 1SR35-100A C4
D7 1S2471
ZD3
2K
10
ZD2 RD22EB2
25V220 D18
D1NL20 C11
16V22 R8
GND
4.7K
R5
RD18EB1
10K
C10
ZD1
C6
D14 1S2471
ZD4 RD27EB1
PB100A
D19
SB007-03SPA
6
VCC VDD
C101
F1
D4 1SR35-100A GND
PC24M05
R9 CRB25T29EFX2610
O IC1
SB007-03SPA D20
CS
1 2 3
CN4 5267-03A
VP
1 2 3
CN5 5267-03A
GNDP
F
26
1
IC1 IC2 IC3 IC4 IC5 IC6 IC7 IC8 IC9 IC10 IC11 IC12 IC13 IC14 IC15 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 UPC24M05HF BA12003 BA12003 BA12003 BA12003 UPD78P044GF-080 TC74HC367AP TC74HC367AP BA10393 S-80727AN-Z BR93LC66A LC36256PLL10/12/15 TC74HC174AP TC74HC174AP TC74HC138AP ECQ-B1H103KFW ECQ-B1H103KFW RT-HE40TKYB101K-T LP5-50V103MS45 RE3-50V470M-T2 RT-HE40TKYB101K-T RE3-35V222M-T2 RT-HE40TKYB101K-T ECQ-B1H332JFW RE3-25V221M-T2 RE2-16V220M-T2 ECQ-B1H103KFW RE3-50V101M-T2 RE2-50V100M-T2 RT-HE40TKYB101K-T RT-HE40TKYB101K-T ECQ-B1H103KFW ECQ-V1H-104-JZW ECQ-B1H103KFW RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T ECQ-B1H103KFW RE2-50V1R0M-T2 RT-HE40TKYB101K-T ECQ-B1H103KFW RT-HE50TKYB102K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKCH150J-T RT-HE40TKCH120J-T RE3-16V101M-T2 ECQ-B1H103KFW ECQ-B1H103KFW RT-HE50TKYB102K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T ECQ-B1H103KFW ECQ-B1H103KFW RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T RT-HE40TKYB101K-T ECQ-B1H103KFW CR-25-2KOHM-J-T CR-25-10KOHM-J-T CR-25-10KOHM-J-T R50XT-08J182 CR-25-10KOHM-J-T CR-25-5.1KOHM-J-T CR-25-100OHM-J-T CR-25-4.7KOHM-J-T CRB25T29EFX3300 CR-25-33KOHM-J-T R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 R25 R26 R27 R28 R29 R30 R31 R32 R33 R34 R35 R36 R37 R38 R39 R40 R41 R42 R43 R44 R45 R46 R47 R48 R49 R50 R51 R52 R53 R54 R55 R56 R57 R58 R59 R60 R61 R62 R63 R64 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 CRB25T29EFX1500 CR-25-56KOHM-J-T CR-25-56KOHM-J-T CR-25-56KOHM-J-T CR-25-56KOHM-J-T CR-25-56KOHM-J-T CR-25-100OHM-J-T CR-25-100OHM-J-T CR-25-100OHM-J-T CR-25-100OHM-J-T CR-25-100OHM-J-T CR-25-100OHM-J-T CR-25-100OHM-J-T CR-25-100OHM-J-T CR-25-1.8KOHM-J-T CR-25-10KOHM-J-T CR-25-4.7KOHM-J-T CR-25-1KOHM-J-T CR-25-56KOHM-J-T CR-25-56KOHM-J-T CR-25-56KOHM-J-T CRH100-FC10-J-1R0 CR-25-10KOHM-J-T CR-25-4.7KOHM-J-T CR-25-4.7KOHM-J-T CR-25-10KOHM-J-T CR-25-10KOHM-J-T CR-25-56KOHM-J-T CR-25-4.7KOHM-J-T CR-25-100KOHM-J-T CR-25-1KOHM-J-T CR-25-56KOHM-J-T CR-25-100OHM-J-T CR-25-56KOHM-J-T CR-25-8.2KOHM-J-T CR-25-100KOHM-J-T CR-25-10KOHM-J-T CR-25-16KOHM-J-T CR-25-10KOHM-J-T CR-25-10KOHM-J-T CR-25-10KOHM-J-T CR-25-56KOHM-J-T CR-25-330KOHM-J-T CR-25-1.8KOHM-J-T CR-25-10KOHM-J-T CR-25-1.8KOHM-J-T CR-25-1.8KOHM-J-T CR-25-10KOHM-J-T CR-25-10KOHM-J-T CR-25-10KOHM-J-T CR-25-56KOHM-J-T CR-25-56KOHM-J-T CR-25-56KOHM-J-T 1S2471 T-77-T 1SR35-100A-T-32-T 1SR35-100A-T-32-T 1SR35-100A-T-32-T 1SR35-100A-T-32-T 1S2471 T-77-T 1S2471 T-77-T 1SR35-100A-T-32-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1SR35-100A-T-32-T 1S2471 T-77-T RB100A-T32-T 1SS83TD 1SS83TD D1NL20-4070 SB007-03SPA SB007-03SPA 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T D24 D25 D26 D27 D28 D29 D30 D31 D32 D33 D34 D35 D36 D37 D38 D39 D40 D41 D42 D43 ZD1 ZD2 ZD3 ZD4 ZD5 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 RA1 RA2 RA3 CA1 CA2 CA3 CA4 CA5 CA6 CA7 X1 X2 CN1 CN2 CN3 CN4 CN5 CN6 CN7 CN8 CN9 CN10 CN11 CN12 CN13 CN14 CN15 CN16 CN17 BZ1 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1SR35-100A-T-32-T 1SR35-100A-T-32-T 1SR35-100A-T-32-T 1S2471 T-77-T 1SR35-100A-T-32-T 1SR35-100A-T-32-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T 1S2471 T-77-T RD18EB1-T1 RD22EB1-T1 RD68EB-T1 RD27EB1-T1 RD15EB3-T1 2SA1015GR.O.Y)TPE2 2SD721 2SC3303-Y 2SD2015 2SD2015 2SC945(K.P.Q.R)-T 2SD1853-AA 2SB926(T.U)-AA 2SB926(T.U)-AA 2SA1015GR.O.Y)TPE2 2SA1015GR.O.Y)TPE2 2SC945(K.P.Q.R)-T 2SD1853-AA 2SD1853-AA DTA143ZS-TP RGLD8X222J RGLD8X563J RGLD8X563J CNB5X101K CNB8X101K CNB8X101K CNB3X101K CNB8X221K CNB8X101K CNB8X101K CST4.19MGW C-002RX(M90-76) HBLB31-S2J 5277-02A 53253-0310 53253-0310 IMSA-9604S-32C IMSA-9604S-18C B3B-XH IL-G-2P-S3T2-E IL-G-3P-S3T2-E IL-G-3P-S3T2-E B2B-EH IL-G-5P-S3T2-E E412198*1 SW1 JPM1030-0201 OSH-3040-SPL T1 F1 F1 F1 F2 DCS-278 UF-0033 21801.6 23702.5 UL-TSCR-0.8A-N1
PKM22EPP-2002
F
27
2
2 1 10 9 8
1 2 3 4 5 6 7 8 9 10 11 12
4 3 2 1 MODE KEY SW.2 9 8 0 C 6 7 8 9 10 1 2 3 4 5 1 2 3 4 5 6 7 PGM RF REG1 REG2 X1 Z1 X2/Z2 OFF C C CLCOM SWI0 D2 SWI1 D3 SWI2 D4 SWI3 D5 SWI4 D6 SWI5 D7 C D26 D25 D24 D23 D22 D21 D14 D13 D12 D11 D20 D19 D18 D17 D10 D9 D8 D15 D16 1S2471 T-77-T
13 14 15 16 17 18 19 20 21 22 23 24
X2/Z2
7 6 3 4
1 C
4 OFF
8 7 6 5 3 2
IMSA-9604S-12C CN2
12 11 10 9 8 7 6 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1
A,D,B,BU
8 7 6
3 2 1 OFF 0 9 8 C C
5 4 3 2 1
IMSA-9604S-10C CN3
1 SWI6 D1 2 PCOM
MCOM PCOM CD7 CD6 CD5 CD4 CD3 CD2 CD1 CD0 VF1 SD SE SG SF SH DG9 DG8 DG7 DG6 DG5 DG4 DG3 DG2 DG1 DG0 SCOM SA SB SC SDP VF2
F
28
12 8 7 14 6 13 5 3 2 11
KC3 KC5 KC6 KC1 KC0 KC2 KC7 KC8 KC9 KC4 K6 K12 K18 K24 K30 K36 K42 K48 K54 K60 K66 K72 K78 KI7 K5 K11 K17 K23 K29 K35 K41 K47 K53 K59 K65 K71 K77 KI6 4 1
TO E278-1
3
K4 K10 K16 K22 K28 K34 K40 K46 K52 K58 K64 K70 K76 KI5 K3 K9 K15 K21 K27 K33 K39 K45 K51 K57 K63 K69 K75
15
K2
K8
K14
K20
K26
K32
K38
K44
K50
K56
K62
K68
K74 KI3 16
TO E278-1
KI4
4
K1 K7 K13 K19 K25 K31 K37 K43 K49 K55 K61 K67 K73
KI2
18
KI1
17
KI0
10
6
6
12 11 10 9 8 7
18 17 16 15 14 13
24 23 22 21 20 19
30 29 28 27 26 25
36 35 34 33 32 31
42 41 40 39 38 37
48 47 46 45 44 43
54 53 52 51 50 49
60 59 58 57 56 55
66 65 64 63 62 61
72 71 70 69 68 67
78 77 76 75 74 73
7 6
5 4 3 2
F
29
US. CANADA
(C, L)
EUROPE
(B, F, G) 240V 230V 220V 120V 100V
*
3
*
2 1
*
2
3
1 0V
L5T18X6X10 L5T18X6X10
0V
L5T18X6X10 L5T18X6X10
TE-278-E2U
TE-278-E2U
L5T18X6X10
4
L5T18X6X10
FG
U.K.
(D)
SJ287505
*
2 1
*
2 1
0V
L5T18X6X10 L5T18X6X10
0V
L5T18X6X10 L5T18X6X10
TE-278-E2U
TE-278-E2U
L5T18X6X10
L5T18X6X10
FG
FG
F
30
SH1019A
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16 17 18 19 20 21 22 23 24
10 9 8 7 6 5 4 3 2 1
CN1 IMSA-9604S-10C
5
12 11 10 9 8 7 6 5 4 3 2 1
CN2 IMSA-9604S-12C
5
TO E278-E2
SWI6 3 R ON
PCOM R OFF
16. PARTS LIST 1. 2. 3. 4. 5. 6. 7. 8. Main PCB ass'y Button ass'y E278-E2 ass'y, Display ass'y 2nd Display ass'y Upper case Lower case Printer unit Drawer
8-1. 8-2. 8-3. 8-4. 8-5. 8-6. DL-2350 (Europe) DL-2351 (Canada) DL-2416 (U.S.A.) DL-2750 (Japan, Germany, Europe) DL-2751 (U.K.) DL-2752 (Germany)
Notes: 1. Price and specifications are subject to change without notice. 2. As for order / supply of spare parts, refer to the "GUIDE BOOK for spare parts supply" a separate publication. 3. Numbers in the item column correspond to the same numbers in exploded drawing. 4. MARKS: N: New parts Q: Quantity used per unit M: Minimum order/supply quantity R: Rank A: Essential B: Stock recommended C: Less recommended X: No stock recommended
33
35
36
37
38
1-28 1-29
1-08
39
1-09
1-30 1-32
1-01
1-31
1-13
41
42
43
44
2-05
2-91
2-92 2-23
2-93
2-21 2-07
2-01
2-16
2-04
2-20 1-01 2-12 2-14 2-06 2-13 2-24 2-03 2-08 2-81 2-10 2-11 1-24 2-02 1-27 3-15 2-09 4-15 3-06 2-16 1-25 2-17 1-26 4-01
45
3-12
3-13
3-11
3-14
3-10
47
48
506 507 505 518 519 508 516 517 503 504 502 503 612 501 613 500 513 102 104 103 509 514 611 515 512 906 100
101 905 904 903 511 200 902 520 510 403 427 431 430 433 606 420 605 604 432 430 431 427 602 603 204 300 203 421 201 425 422 419 426 423 424 301 900 202 427 429 901
404
302 303
410
412 407
409 411
428 607 434 608 417 427 610 416 609 415 411 401 409 408 402 410 413
414
421 418
400
49
50
DL-2350
5-01
5-02 5-18 5-15 5-17 5-20 5-19 5-14 5-12 5-05 5-06 5-13 5-09 5-04 5-08 5-37 5-22 5-26 5-07 5-16
5-25
52
DL-2351
6-01
6-14
6-05 6-06 6-07 6-13 6-04 6-08 6-37 6-22 6-26 6-09
6-25
6-24 6-23
6-39
53
54
DL-2416
7-01
7-14 7-12
7-19 7-16
7-05 7-06 7-07 7-13 7-04 7-08 7-37 7-22 7-26 7-09
7-25
7-24 7-23
7-39
55
56
DL-2750
8-01
8-14 8-12
8-19 8-16
8-05 8-06 8-07 8-13 8-04 8-08 8-37 8-22 8-26 8-09
8-25
8-24 8-23
8-39
57
58
DL-2751
9-01
9-18 9-17
9-19 9-14 9-12 9-05 9-06 9-07 9-13 9-04 9-08 9-37 9-22 9-26 9-09 9-16
9-25
9-24 9-23
9-39
59
60
DL-2752
10-01
10-18 10-17
10-19 10-14 10-12 10-05 10-06 10-07 10-13 10-04 10-08 10-37 10-22 10-26 10-09 10-16
10-25
10-36 10-40
10-24 10-23
10-38 10-39
61