Académique Documents
Professionnel Documents
Culture Documents
Application
Simple, menu-guided on-site operation Envelope curves on the on-site display Easy operation, diagnosis and
measuring point documentation with the supplied ToF Tool operating program. Alignable IP 68 aluminium housing optional remote display and operation Installation possible from thread G 1 or 1 NPT upwards Integrated temperature sensor for timeof-flight correction. Accurate measurements, even for temperature changes Linearisation function (up to 32 points) for measured value output in any unit of length, volume or flow rate Non-contact measurement method, therefore almost independent of product properties for simple diagnosis with four-line plain text display
Prosonic M
Inhaltsverzeichnis
Function and system design . . . . . . . . . . . . . . . . . . 3
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Equipment architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Process conditions . . . . . . . . . . . . . . . . . . . . . . . . . 20
Process temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Process pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mechanical construction . . . . . . . . . . . . . . . . . . . . 21
Design / dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Housing design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Process connection, sealing material, sensor material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 22 22
Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Load HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linearisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 10 10 10
22
Human interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Display and operating elements . . . . . . . . . . . . . . . . . . . 23 On-site operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Auxiliary energy . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Terminal compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . Fieldbus plug connector . . . . . . . . . . . . . . . . . . . . . . . . . . Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Current consumption (2-wire-instruments) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HART ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Max. noise HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 11 12 13 13 13 13 13 13 14
Ordering information . . . . . . . . . . . . . . . . . . . . . . . 27
Product structure FMU 40 . . . . . . . . . . . . . . . . . . . . . . . . Product structure FMU 41 . . . . . . . . . . . . . . . . . . . . . . . . Product structure FMU 42 . . . . . . . . . . . . . . . . . . . . . . . . Product structure FMU 43 . . . . . . . . . . . . . . . . . . . . . . . . Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 28 29 30 30
Performance characteristics . . . . . . . . . . . . . . . . . 14
Reaction time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reference operating conditions . . . . . . . . . . . . . . . . . . . . Measured value resolution . . . . . . . . . . . . . . . . . . . . . . . . Pulse frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Measuring error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 14 14 14
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Weather protection cover . . . . . . . . . . . . . . . . . . . . . . . . . Installation bracket for FMU 40/41 . . . . . . . . . . . . . . . . . . Adapter flange for FMU 40 / FMU 41 . . . . . . . . . . . . . . . . Cantilever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Frame for Cantilever . . . . . . . . . . . . . . . . . . . . . Wall Bracket for Cantilever . . . . . . . . . . . . . . . . . . . . . . . . Commubox FXA 191 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service Interface FXA 193 . . . . . . . . . . . . . . . . . . . . . . . . Remote display FHX 40 . . . . . . . . . . . . . . . . . . . . . . . . . . 31 31 32 33 34 34 34 35 35
Installation conditions . . . . . . . . . . . . . . . . . . . . . . 15
Installation variants FMU 40, FMU 41 . . . . . . . . . . . . . . . . Installation variants FMU 42 . . . . . . . . . . . . . . . . . . . . . . . Installation variants FMU 43 . . . . . . . . . . . . . . . . . . . . . . . Installation conditions for level measurements . . . . . . . . . Installation in narrow shafts . . . . . . . . . . . . . . . . . . . . . . . . Installation conditions for flow measurements . . . . . . . . . Blocking distance, nozzle installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 15 16 16 17 17 19
Supplementary documentation . . . . . . . . . . . . . . . 37
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description of device functions . . . . . . . . . . . . . . . . . . . . Short instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control drawings Installation drawings . . . . . . . . . . . . . . 37 37 37 37 37 38
Ambient conditions. . . . . . . . . . . . . . . . . . . . . . . . . 20
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resistance to alternating temperature cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ingress protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . . 20 20 20 20 20 20 20
Endress + Hauser
Prosonic M
BD
20 mA 100% D
4 mA 0%
L00-FMU4x-15-00-00-de-001
E: Empty distance; F: Span (full distance); D: Distance from sensor membrane - product surface; L: Level; BD: Blocking distance
Time-of-flight method The sensor of the Prosonic M transmits ultrasonic pulses in the direction of the product surface. There, they are reflected back and received by the sensor. The Prosonic M measures the time t between pulse transmission and reception. The instrument uses the time t (and the velocity of sound c) to calculate the distance D between the sensor membrane and the product surface: D = c t/2 As the device knows the empty distance E from a user entry, it can calculate the level as follows: L=E-D An integrated temperature sensor compensates for changes in the velocity of sound caused by temperature changes. Interference echo suppression The interference echo suppression feature on the Prosonic M ensures that interference echos (e.g. from edges, welded joints and installations) are not interpreted as a level echo. Calibration Enter the empty distance E and the span F to calibrate the device. Blocking distance Span F may not extend into the blocking distance BD. Level echos from the blocking distance cannot be evaluated due to the transient characteristics of the sensor.
Endress + Hauser
Prosonic M
Equipment architecture
420 mA output with HART protocol The complete measuring system consists of:
PLC - COMMUWIN II - ToF Tool - ToF Tool
transmitter power supply unit RMA 422 or RN 221 N (communication resistor included)
HELP
ENDRESS + HAUSER
352 mbar 0 C
SAVE
9
Bksp Page On #%& ABC
Page Up
6
Delete
DEF
1
Copy GHI
2
Paste JKL
3
Hot Key MNO
4
PQRS
5
Insert TUV
6
+ Hot Key W XY Z
7
,()
8
_<>
9
+*/
375
FIELD COMMUNICATOR
L00-FMxxxxxx-14-00-06-en-007
If the HART communication resistor is not built into the supply unit, it is necessary to insert a communication resistor of 250 into the 2-wire line. On-site operation
with display and operating module VU 331 with a Personal Computer, FXA 193 and the operating software ToF Tool
Remote operation
with HART handheld terminal DXR 375 with a Personal Computer, Commubox FXA 191 and the operating software COMMUWIN II
respectively ToF Tool.
Endress + Hauser
Prosonic M
System integration using PROFIBUS PA A maximum of 32 transmitters (8 if mounted in an explosion hazardous location EEx ia IIC according to FISCO-model) can be connected to the bus.The segment coupler provides the operating voltage to the bus. Both on-site as well as remote operation are possible.
personal computer e.g. with Commuwin II or ToF Tool and Profibard resp. Proficard
PLC
PROFIBUS PA
More Functions (valves etc) Prosonic M FXA 193 Levelflex M ToF Tool
L00-FMxxXXXX-14-00-06-en-001
Micropilot M
Endress + Hauser
Prosonic M
System integration using Foundation Fieldbus (FF) A maximum of 32 transmitters (standard or EEx d) can be connected to the bus. For protection class EEx ia: the maximum number of transmitters depends on the established rules and standards for intrinsically safe circuits (EN 60070-14) and proof of instrinsic safety. Both on-site and remote operation are possible.
FF link
ENDRESS + HAUSER
Micropilot M
Endress + Hauser
Prosonic M
System integration using Endress+Hauser Rackbus You can interconnect a maximum of 64 devices with HART protocol to a Rackbus. Use an FXN 672 interface module for each device. You can integrate this bus into a higher-level bus by using a ZA gateway. Gateways are available for MODBUS, FIP, PROFIBUS, INTERBUS etc. Both on-site and remote operation are possible.
PLC
ZA 672
ZA 672
+
mA1
+
mA1
+
mA1
ENDRESS + HAUSER
Micropilot M
Endress + Hauser
Prosonic M
Input
Measured variable The distance D between the sensor membrane and the product surface is measured. Using the linearisation function, the device uses D to calculate: level L in any units volume V in any units flow Q across measuring weirs or open channels in any units Measuring range The measuring range is limited by the range of a sensor. The sensor range is, in turn, dependent on the operating conditions. To estimate the actual range, proceed as follows (see also the calculation example in the diagram): 1. 2. 3. Determine which of the influences shown in the following table are appropriate for your process. Add the corresponding attenuation values. From the total attenuation, use the diagram to calculate the range.
Attenuation 0 dB 5 ... 10 dB 10 ... 20 dB Ask E+H
Bulk material surface Hard, rough (e.g. rubble) Soft (e.g. peat, dust-covered clinker)
Attenuation 40 dB 40 ... 60 dB
Attenuation 0 dB 5 dB 5 ... 20 dB
Attenuation
0 dB 5 ... 10 dB 10 ... 20 dB
Endress + Hauser
Prosonic M
15 FMU 43 14 13 12 11 10 FMU 42 9
range/ m
8 7 6 5 4 3 2 1
10 20 30 40 50 60 70 80
FMU 41
FMU 40
attenuation / dB
L00-FMU4xxxx-05-00-00-en-002
Dust-covered rubble Medium dust development No filling curtain in detection range Temperature diff. < 20C
Operating frequency
Operating frequency approx. 70 kHz approx. 50 kHz approx. 42 kHz approx. 35 kHz
Endress + Hauser
Prosonic M
Output
Output signal
Signal on alarm
10
Endress + Hauser
Prosonic M
Auxiliary energy
Terminal compartment In the F12 housing, the terminals are located underneath the housing cover. In the T12 housing, they are under the cover of the separate terminal compartment.
F12 housing T12 housing
L00-FMR2xxxx-04-00-00-en-001
For the PROFIBUS-PA version, there is a version available with an M12 plug connector. For the Foundation Fieldbus variant, there is a version available with a 7/8" plug connector.
These versions are supplied fully-wired.
Foundation Fieldbus 7/8 plug Profibus M 12 plug
L00-FMxxxxxx-04-00-00-en-003
Endress + Hauser
11
Prosonic M
Terminal assignment
power
Auxiliary energy
alternatively Commubox FXA 191 DXR 375 communication resistor (> 250 )
alternatively
1 2 3 4
LL+ I+ I-
5 6
I+ I-
1 2
L1/L+ N/L-
plant ground
L00-FMxxxxxx-04-00-00-en-004
L00-FMxxxxxx-04-00-00-en-001
Connect the connecting line to the screw terminals (line cross-sections of 0.5 ... 2.5mm) in the Use 2-wire twisted pair cable with screen for the connection. Protective circuitry against reverse polarity, RFI and over-voltage peaks is built into the device
(see also Technical Information TI 241F/00/en "EMC Test Procedures") terminal compartment.
PROFIBUS PA
Foundation Fieldbus
L00-FMR2xxxx-04-00-00-de-003
L00-FMR2xxxx-04-00-00-de-007
The digital communication signal is transmitted to the bus via a 2-wire connection. The bus also provides the auxiliary energy. Please use 2-wire twisted pair cable with screen. Refer to the following operating manuals for information on cable types, and how to set up and ground the network: BA 198F/00/de PROFIBIS -DP/-PA, Guidelines for planning and commissioning BA 013S/04/en Foundation Fieldbus, Installation and Commissioning Guidelines
12
Endress + Hauser
Prosonic M
Supply voltage
HART, 2-wire The following values are the voltages across the terminals directly at the instrument:
Version 2-wire HART Standard 20 mA 4 mA EEx ia 20 mA 4 mA EEx d 20 mA Fixed current, adjustable, e.g. for solar power operation (measured value via HART) Fixed current for HART multidrop mode 1) Standard 11 mA 11 V 10 V 30 V 36 V 8V 14 V 30 V 30 V 8V 14 V 36 V 30 V Current consumption 4 mA Terminal voltage minimum 14 V Terminal voltage maximum 36 V
11 mA 4 mA1 4 mA
1
10 V 14 V 14 V
30 V 36 V 30 V
Start-up current 11 mA
Cable entry
Cable gland: M20x1.5 (recommended cable diameter 6 ... 10 mm) Cable entry G or NPT PROFIBUS-PA M12 plug Fieldbus Foundation 7/8" plug
Power consumption 51 mW ... 800 mW max. 4VA 330 mW ... 830 mW 600 mW ... 1 W
Power consumption
Version 2-wire 4-wire AC 4-wire DC; FMU 40/41 4-wire DC; FMU 42/43
47...125 Hz: Vpp = 200 mV (measured at 500 ) 500 Hz...10 kHz: Vrms = 2.2 mV (measured at 500 )
Endress + Hauser
13
Prosonic M
Galvanic isolation
With 4-wire devices, the evaluation electronics and mains voltage are galvanically isolated from each other.
Performance characteristics
Reaction time The reaction time depends on the parameter settings (min. 0.5s for 4-wire devices, min. 2s for 2-wire devices).
Temperature = +20 C Pressure = 1013 mbar abs. Humidity = 50 % Ideal reflective surface (e.g. calm, smooth fluid surface) No interference reflections within signal beam Set application parameters: Tank shape = flat ceiling Medium property = liquid process conditions = calm surface
Measured value resolution 1 mm 1 mm 2 mm 2 mm
Pulse frequency
Measuring error
Typical specifications for reference operating conditions (include linearity, repeatability, and hysteresis):
Sensor FMU 40 FMU 41 FMU 42 FMU 43 Measuring error 2mm or 0.2% of set measuring range1 2 mm or 0,2% of set measuring range1 4 mm or 0,2% of set measuring range1 4 mm or 0,2% of set measuring range1
whichever is greater
14
Endress + Hauser
Prosonic M
Installation conditions
Installation variants FMU 40, FMU 41 Installation with counter nut Installation with sleeve
adapter flange
sensor
nozzle
L00-FMU4xxxx-17-00-00-en-002
L00-FMU42xxxx-17-00-00-en-001
Endress + Hauser
15
Prosonic M
slip-on flange
nozzle
e.g. Zone 20
sensor
Zone 20
L00-FMU43xxxx-17-00-00-en-001
7 1 1/6D D 6 5
L00-FMU4xxxx-17-00-00-de-005
Do not install the sensor in the middle of the tank (3). We recommend leaving a distance Use a protective cover, in order to protect the device from direct sun or rain (2). Avoid measurements through the filling curtain (4). Make sure that equipment (5) such as limit switches, temperature sensors, etc. are not located
between the sensor and the tank wall (1) measuring 1/6 of the tank diameter.
within the emitting angle . In particular, symmetrical equipment (6) such as heating coils, baffles etc. can influence measurement. Align the sensor so that it is vertical to the product surface (7). Never install two ultrasonic measuring devices in a tank, as the two signals may affect each other. To estimate the transmitted echo beam and its detection range, use the 3 dB emitting angle .
Sensor FMU 40 FMU 41 FMU 42 FMU 43 11 11 11 6 L 5m 8m 10 m 15 m r 0,48 m 0,77 m 0,96 m 0,79 m
16
Endress + Hauser
Prosonic M
In narrow shafts with strong interference echoes, we recommend using an ultrasound guide pipe (e.g. PE or PVC wastewater pipe) with a minimum diameter of 100 mm. Make sure that the pipe is not soiled by accumulated dirt. If necessary, clean the pipe at regular intervals.
ENDRESS+HAUSER Prosonic M
ENDRESS+HAUSER Prosonic M
venting hole
L00-FMU4xxxx-17-00-00-en-010
Install the Prosonic M at the inflow side, as close above the maximum water level Hmax as
possible, plus the blocking distance BD. Position the Prosonic M in the middle of the channel or weir. Align the sensor membrane parallel to the water surface. Keep to the installation distance of the channel or weir. You can enter the "Flow to Level" linearisation curve ("Q/h curve") using ToF Tool or manually via the on-site display.
inflow
empty calibr.
outflow
BD
Hmax
direction of flow
1 x b0
b0
L00-FMU4xxxx-17-00-00-en-003
Endress + Hauser
17
Prosonic M
min. 3 H max BD
empty calibr.
L00-FMU4xxxx-17-00-00-en-012
18
Endress + Hauser
Prosonic M
Install the Prosonic M at a height so that the blocking distance BD is not undershot, even at maximum fill level. Use a pipe nozzle if you cannot maintain the blocking distance in any other way. The interior of the nozzle must be smooth and may not contain any edges or welded joints. In particular, there should be no burr on the inside of the tank side nozzle end. Note the specified limits for nozzle diameter and length. To minimise disturbing factors, we recommend an angled socket edge (ideally 45).
FMU 43 FMU 40/41 BD SD FMU 42
F
L L D D D
L00-FMU4xxxx-17-00-00-en-004
BD: blocking distance; SD: safety distance; E: empty calibration; F: full calibration (span); D: nozzle diameter; L: nozzle length
Sensor
BD
nozzle diameter 50 mm
max. nozzle length ca. 80 mm ca. 240 mm ca. 300 mm ca. 240 mm ca. 300 mm ca. 300 mm
FMU 40
0.25 m
5m
2m
80 mm 100 mm 80 mm
8m 10 m 15 m
" !
Caution! If the blocking distance is undershot, it may cause device malfunction. Note! In order to prevent the level from entering the blocking distance, you can specify a safety distance (SD). If the level is within this safety distance, the Prosonic M outputs a warning or alarm message.
Endress + Hauser
19
Prosonic M
Ambient conditions
Ambient temperature -40 C ... +80 C The functionality of the LC display becomes restricted at Tu<-20 C and Tu>+60 C. If the device is operated outdoors in strong sunlight, you should use a protective cover. -40 C ... +80 C to DIN EN 60068-2-14; Nb test : +80C/-40C, 1K/min, 100cycles
Storage temperature Resistance to alternating temperature cycles Climate class Ingress protection
"
Vibration resistance Electromagnetic compatibility (EMC)
Interference emission to EN 61326, Equipment Class B Interference immunity to EN 61326, Appendix A (Industrial) and NAMUR Recommendation NE A standard installation cable is sufficient if only the analogue signal is used. Use a screened
cable when working with a superimposed communication signal (HART). 21 (EMC).
Process conditions
Process temperature -40C ... +80C A temperature sensor is integrated in the sensor for temperature-dependent time-of-flight correction.
Process pressure
20
Endress + Hauser
Prosonic M
Mechanical construction
Design / dimensions F12 housing
ca. 86 65 78
T12 housing
68 94 65 32 78
85
150
85
FMU 40
60 AF
~148
FMU 41
60 AF
162
ENDRESS+HAUSER Prosonic M
129
ENDRESS+HAUSER Prosonic M
129
~87
~83
~148
22
G1 1 NPT
G2 2 NPT
70
39 50
F12
ENDRESS+HAUSER Prosonic M
F12/ T12
30 90
M8
75
158
75
119
ENDRESS+HAUSER Prosonic M
129
150
2 x M8 85
~248
2
40 ANSI 4 DN 100 Alternatively, a separate flange can be used. 40
25
230
11
L00-FMU4xxxx-06-00-00-en-003
Endress + Hauser
~123
120
~ 88
22
21
Prosonic M
Weight
Housing design
Types of housings
F12 housing with sealed terminal compartment for standard or EEx ia applications T12 housing with separate terminal compartment and explosionproof encapsulation
Material Aluminium, seawater resistant, chromed, powder-coated Cover
Aluminium, for version without on-site display Inspection glass for version with on-site display. This version cannot be supplied together with
the ATEX II 1/2 D certificate. Process connection, sealing material, sensor material
Sensor FMU 40 FMU 41 Process connection Material in contact with process Sensor: PVDF Seal: EPDM Sensor: PVDF Seal: EPDM Sensor: PVDF Seal: VITON or EPDM Flange: PP, PVDF or SS 316
Thread G 1 Thread NPT 1 - 11.5 Thread 2" Thread NPT 2" - 11,5 Universal flange DN 80 / ANSI 3" / JIS10K80 Universal flange DN 100 / ANSI 4" / JIS16K100 Mounting bracket Universal flange DN 80 / ANSI 3" / JIS10K80 Universal flange DN 100 / ANSI 4" / JIS16K100 Mounting bracket
FMU 42
FMU 43
22
Endress + Hauser
Prosonic M
Human interface
Display and operating elements The LCD module VU 331 for display and operation is located beneath the housing cover. The measured value is legible through the glass in the cover. Open the cover to operate the device.
END
Order MICR S+HA Code: OPIL Ser.-No OT USE .: Messbe Measur reich ing range U 16...36 max. 4...20 20 m mAV DC
RES
II
IP
T
A >70C
65
Made in Germany
Maulburg
: t >85C
Symbols
3 keys
L00-FMxxxxxx-07-00-00-en-001
Symbol in display continuous Meaning Alarm flashing Warning Communication Security Locking
Navigate upwards in the selection list Edit numeric value within a function Navigate downwards in the selection list Edit numeric value within a function
Hardware lock / unlock After a hardware lock, an operation of the instrument via display or communication is not possible! The hardware can only be unlocked via the display. An unlock parameter must be entered to do so.
Endress + Hauser
23
Prosonic M
On-site operation
Operation with VU 331 The LC-Display VU 331 allows configuration via 3 keys directly at the instrument. All device functions can be set through a menu system. The menu consists of function groups and functions. Within a function, application parameters can be read or adjusted. The user is guided through a complete configuration procedure.
Headline
ENDRESS + HAUSER
Position indicator
Symbol
+ E
Main value
Unit
Selection list
X
O S
FG00 FG01 FG02 FG03 FG04 FG05 FG06 FG07 ...
F
F000 F001 F002 F003 F004 ...
O S
X
Envelope curve
Help text
L00-FMU4xxxx-07-00-00-en-004
Operation with the handheld terminal DXR 375 On devices with HART communication, you can also access the menu using the handheld terminal DXR 375.
8.7 m
Delete
HELP
SAVE
9
Bksp #%&
Page Up
6
Delete
HELP
SAVE
FMU43: LIC0001 GROUP SELECTION 1 2 3 4 5 BASIC SETUP SAFETY SETTINGS TEMPERATURE LINEARISATION EXTENDED CALIBR.
Delete
Page On
Bksp
DEF
ABC
1
Copy GHI
2
Paste JKL
3
Hot Key MNO
H
SAVE HOME
4
PQRS
5
Insert TUV
6
+ Hot Key W XY Z
FMRU43: LIC0001 BASIC SETUP 1 2 3 4 5 MEASURED VALUE TANK SHAPE MEDIUM PROPERTY PROCESS COND. EMPTY CALIBR.
7
,()
8
_<>
9
+*/
Page Up Page On
Bksp
375
FIELD COMMUNICATOR
SAVE HOME
L00-FMU4xxxx-07-00-00-de-005
24
Endress + Hauser
Prosonic M
Remote operation
Operation with ToF Tool The ToF Tool is a graphical operation software for instruments from Endress+Hauser. It is used to support commissioning, securing of data, signal analysis and documentation of the instruments. It is compatible with the following operating systems: Win95, Win98, WinNT4.0 and Win2000. The ToF Tool supports the following functions: Online configuration of transmitters Signal analysis via envelope curve Loading and saving of instrument data (Upload/Download) Documentation of measuring point Connection options HART with Commubox FXA 191 (available as accessory) PROFIBUS PA Service-interface with adapter FXA 193 (available as accessory) Menu-guided commissioning:
L00-FMU4xxxx-19-00-00-en-003
L00-FMU4xxxx-19-00-00-en-004
Endress + Hauser
25
Prosonic M
Operation with Commuwin II (for communication variants HART or PROFIBUS-PA) Commuwin II is an operating software with graphical support (MS Windows) for intelligent transmitters with the communication protocols Rackbus, Rackbus RS-485, HART and PROFIBUSPA. Commuwin II supports the following functions: Online configuration of transmitters Loading and saving of instrument data (Upload/Download) Orderly visualisation of measured values and limit values Display and recording of measured values with a line recorder It is not possible to display envelope curves with Commuwin II. To display them, please use the ToF Tool program supplied. Connections: HART with Commubox FXA 191 (available as accessory) PROFIBUS PA Operation with NI-FBUS Configurator (only Foundation Fieldbus) The NI-FBUS Configurator is an easy-to-use graphical environment for creating linkages, loops, and a schedule based on the fieldbus concepts. You can use the NI-FBUS Configurator to configure a fieldbus network as follows: Set block and device tags Set device addresses Create and edit function block control strategies (function block applications) Configure vendor-defined function and transducer blocks Create and edit schedules Read and write to function block control strategies (function block applications) Invoke Device Description (DD) methods Display DD menus Download a configuration Verify a configuration and compare it to a saved configuration Monitor a downloaded configuration Replace devices Save and print a configuration
Ex approval
26
Endress + Hauser
Prosonic M
Ordering information
Product structure FMU 40
Certificates A Variant for non-hazardous area 1 ATEX II 1/2 G or II 2 G; EEX ia IIC T6 4 ATEX II 1/2 G or II 2 G; EEX d [ia] IIC T6 S FM IS Cl. I,II,III Div. 1 Gr. A-G / NI Cl. I Div. 2 T FM XP Cl. I,II,III Div. 1 Gr. A-G U CSA IS Cl. I,II,III Div. 1 Gr. A-G / NI Cl. I Div. 2 V CSA XP Cl. I,II,III Div. 1 Gr. A-G N CSA General Purpose K TIIS Ex ia II C T6 Y Special certificate Process connection R G 1 threadISO 228 N NPT 1 - 11,5 thread Y Special version Power supply/communication B 2 wire, 4...20mA-loop/HART H 4 wire, 10,5...32VDC / 4-20mA HART G 4 wire, 90...253VAC / 4-20mA HART D 2 wire, PROFIBUS PA F 2 wire, Foundation Fieldbus Y Special version Display / on-site operation 1 Without LC display 2 With LC display VU 331 incl. on-site operation 3 Prepared for remote display FHX 40 9 Special version Housing A Aluminium F12 housing coated to IP 68 C Aluminium T12 housing coated to IP 68; with separate terminal compartment D Aluminium T12 housing coated to IP 68; with separate terminal compartment; with overvoltage protection (in preparation) 9 Special version Screw union/entry 2 M20x1.5 screw union 3 G 1/2 entry 4 NPT 1/2 entry 5 M12 PROFIBUS-PA plug-in connector 6 7/8" FF plug 9 Special version FMU 40 Product designation
Endress + Hauser
27
Prosonic M
Certificates A Variant for non-hazardous area 1 ATEX II 1/2 G or II 2 G; EEX ia IIC T6 4 ATEX II 1/2 G or II 2 G; EEX d [ia] IIC T6 S FM IS Cl. I,II,III Div. 1 Gr. A-G / NI Cl. I Div. 2 T FM XP Cl. I,II,III Div. 1 Gr. A-G U CSA IS Cl. I,II,III Div. 1 Gr. A-G / NI Cl. I Div. 2 V CSA XP Cl. I,II,III Div. 1 Gr. A-G N CSA General Purpose K TIIS Ex ia II C T6 Y Special certificate Process connection R G 1 threadISO 228 N NPT 1 - 11,5 thread Y Special version Power supply/communication B 2 wire, 4...20mA-loop/HART H 4 wire, 10,5...32VDC / 4-20mA HART G 4 wire, 90...253VAC / 4-20mA HART D 2 wire, PROFIBUS PA F 2 wire, Foundation Fieldbus Y Special version Display / on-site operation 1 Without LC display 2 With LC display VU 331 incl. on-site operation 3 Prepared for remote display FHX 40 9 Special version Housing A Aluminium F12 housing coated to IP 68 C Aluminium T12 housing coated to IP 68 with separate terminal compartment D Aluminium T12 housing coated to IP 68; with separate terminal compartment; with overvoltage protection (in preparation) 9 Special version Screw union/entry 2 M20x1.5 screw union 3 G 1/2 entry 4 NPT 1/2 entry 5 M12 PROFIBUS-PA plug-in connector 6 7/8" FF plug 9 Special version FMU 41 Product designation
28
Endress + Hauser
Prosonic M
Certificates A Variant for non-hazardous area 1 ATEX II 1/2 G EEX ia IIC T6 (in preparation) 4 ATEX II 1/2 G EEX d [ia] IIC T6 (in preparation) G ATEX II 3G EEx nA II T6 (in preparation) S FM IS Cl. I,II,III Div. 1 Gr. A-G / NI Cl. I Div. 2 (in preparation) T FM XP Cl. I,II,III Div. 1 Gr. A-G (in preparation) U CSA IS Cl. I,II,III Div. 1 Gr. A-G / NI Cl. I Div. 2 (in preparation) V CSA XP Cl. I,II,III Div. 1 Gr. A-G (in preparation) N CSA General Purpose (in preparation) K TIIS Ex ia II C T6 (in preparation) Y Special certificate Process connection M mounting bracket FAU20 P DN80/ANSI 3"/JIS10K80, PP, Universal flange Q DN80/ANSI 3"/JIS10K80, PVDF, Universal flange S DN80/ANSI 3"/JIS10K80, 316L, Universal flange T DN100/ANSI 4"/JIS16K100, PP, Universal flange U DN100/ANSI 4"/JIS16K100, PVDF, Universal flange V DN100/ANSI 4"/JIS16K100, 316L, Universal flange Y Special version Power supply/communication B 2 wire, 4...20mA-loop/HART H 4 wire, 10,5...32VDC / 4-20mA HART G 4 wire, 90...253VAC / 4-20mA HART D 2 wire, PROFIBUS PA F 2 wire, Foundation Fieldbus Y Special version Display / on-site operation 1 Without LC display 2 With LC display VU 331 incl. on-site operation 3 Prepared for remote display FHX 40 9 Special version Housing A Aluminium F12 housing coated to IP 68 C Aluminium T12 housing coated to IP 68, with separate terminal compartment D Aluminium T 12 housing coated to IP 68, with separate terminal compartment; with overvoltage protection (in preparation) Y Special version Gland/Entry 2 M20x1.5 gland 3 G 1/2 entry 4 NPT 1/2 entry 5 M12 PROFIBUS-PA plug 6 7/8" FF plug 9 Special version Sealing Sensor/Flange 2 VITON flat sealing 3 EPDM flat sealing 9 special version Additional options A Additional options not selected FMU 42 Product designation
Endress + Hauser
29
Prosonic M
Certificates A Variant for non-hazardous area 2 ATEX II 1/2 D or II 2 D, Aluminium Deckel 5 ATEX II 1/3 D or II 3 D, Sichtdeckel M FM DIP Class II, III, Div. 1, Gr. E,F,G NI N CSA General Purpose P CSA DIP, Class II, III, Div. 1, Gr. E,F,G NI Y Special version Process connection/material P Flange DN 100/ANSI 4"/JIS 16K100, PP (universal slip-on flange included) S Flange DN 100/ANSI 4"/JIS 16K100, SS 316TI (universal slip-on flange included) K Without slip-on flange/without mounting bracket (customer mounting equipment) M With mounting bracket Y Special version Power supply/communication H 4 wire, 10,5...32VDC / 4-20mA HART G 4 wire, 90...253VAC / 4-20mA HART D 2 wire, PROFIBUS PA F 2 wire, Foundation Fieldbus Y Special version Display / on-site operation 1 Without LC display 2 With LC display VU 331 incl. on-site operation 3 Prepared for remote display FHX 40 9 Special version Housing A Aluminium F12 housing coated to IP 68 9 Special version Screw union/entry 2 M20x1.5 screw union 3 G 1/2 entry 4 NPT 1/2 entry 5 M12 PROFIBUS-PA plug-in connector 6 7/8" FF plug 9 Special version FMU 43 Product designation
Scope of delivery
Instrument according to the version ordered 2 ToF Tool CDs (1: program, 2: Device Descriptions and Documentation) Operating manual according to the communication version for certified instrument versions: Safety Instructions, Control- or Installation drawings for FMU 40/41 in the versions FMU 40 *R**** and FMU 41 *R****: counter nut (PA) for FMU 40/41: sealing ring (EPDM)
30
Endress + Hauser
Prosonic M
Accessories
Weather protection cover A Weather protection cover made of stainless steel is available for outdoor mounting (order code: 543199-0001). The shipment includes the protective cover and tension clamp.
Orde ICR SS r OP +HA Se Code r.-No ILO US : .: T E Me Messbere asur ich ing rang e ma U 16 x. 20 ...3 4...20 6 m mAV DC
EN D M RE
II
IP
T
A >7
65
5C
Made in Germany
0C
: t >8
Maulburg
L00-FMR2xxxx-00-00-06-en-001
400 120
16
250
30
120
L00-FMU4x-00-00-00-de-001
for FMU 40, G1: Order No. 942669-0000 for FMU 41, G2: Order No. 942669-0001
suited for NPT 1" and 2" as well
Endress + Hauser
31
Prosonic M
adapter flange
sensor
nozzle
L00-FMUX3XXX-00-00-00-en-001
32
Endress + Hauser
Prosonic M
Cantilever
20 C
20
35
M8
75
75
100
35
50/ 62
22
105
6.5
15
L00-FMU4xxxx-06-00-00-yy-005
A 585 mm
B 250 mm
C 2 mm
D 200 mm
25
FMU 41
1085 mm
750 mm
3 mm
300 mm
FMU 40
FMU 41
The 50 mm or 62 mm orifices serve for the mounting of the FMU 40 or FMU 41 sensor, The 22 mm orifice may be used for an additional sensor.
respecitvely.
Endress + Hauser
50 100
Order Code 52014132 52014131 52014136 52014135 52014134 52014133 52014138 52014137
33
Prosonic M
55
3.2
33.7
25
60
700/1400
20
45 6.5
4
76
130
100 150
L00-FMU4x-00-00-00-yy-005
Material galv. steel 1.4301 (AISI 304) galv. steel 1.4301 (AISI 304)
33.7
100 200
25
13
88
110 150
L00-FMU4x-00-00-00-yy-006
For intrinsically safe communication between HART protocol and Personal Computer. The Prosonic can be operated either with the ToF Tool program or with the Commuwin II program. You can find additional information in Technical Information TI 237F/00/en.
34
110
150
Endress + Hauser
Prosonic M
For communication with ToF Tool via the display connector. Ordering structure: FXA 193-A: for use in non-hazrdous area FXA 193-B: for use in hazardous area (ATEX, CSA, FM) The connection to a ToF device needs an additional FXA connection cable (order code.: 50101787).
Endress + Hauser
35
Prosonic M
Dimensions
Maulburg
A >7
0C :
t >8
5C
Made in Germany
D Cable
160
IP
65
180
EN DR ES S+ HA US ER
8, 5
88
120 82 118
6, 3
96 max. 80 min. 30
106
122
pipe
L00-FMxxxxxx-00-00-06-en-003
Technical data:
Max. cable length Temperature range Degree of protection Material for housing Dimensions [mm] / [inch] 20 m (65 ft) -30 C...+70 C (-22 F...158 F) IP65 acc. to EN 60529 (NEMA 4) Alloy of Aluminium AL Si 12 122x150x80 (HxBxT) / 4.8x5.9x3.2
Ordering structure
Certificates
A 1 S U N For non-hazardous area ATEX II 2 G EEx ia IIC T6, ATEX II 3D FM IS Class I Div. 1, Groups A,B,C,D CSA IS Class I, Div. 1, Groups A,B,C,D CSA General Purpose (in preparation)
Cable length
1 20 m cable
Additional option
A B Additional option not selected Mounting bracket 1" or 2" pipe
FHX 40 -
36
Endress + Hauser
Prosonic M
Supplementary documentation
System Information SI 005F/00/en Ultrasonic level measurement Operating manual Depending on the communication variant ordered, the following operating manuals are supplied with the device:
Communication 4 ... 20mA, HART Profibus PA Foundation Fieldbus Operating manual BA 237F BA 238F BA 239F
These instructions describe the installation and first commissioning of the Prosonic M. From the operating menu, all functions are included, which are required for standard measurement tasks. Additional functions are not contained in the manual. Description of device functions BA 240F This contains a detailed description of all the functions of the Prosonic M and is valid for all communication variants. This document is located on the supplied documentation CD-ROM in the form of a pdf file. It is also available on the Internet at www.endress.com. KA 183F can be found under the device housing cover. The most important menu functions are summarised on this sheet. It is intended primarily as a memory jogger for users who are familiar with the operating concept of Endress+Hauser time-offlight instruments. Safety Instructions The following safety instructions are supplied with ATEX-certified device versions:
Version Certificate ATEX II 1/2 G bzw. II 2 G EEx ia II C T6 ATEX II 1/2 G bzw. II 2 G EEx ia II C T6 Communication HART Safety Instructions XA 174F
Short instructions
FMU 40 - 1*B*** FMU 41 - 1*B*** FMU 40 - 1*D*** FMU 40 - 1*F*** FMU 41 - 1*D*** FMU 41 - 1*F*** FMU 40 - 4***** FMU 41 - 4***** FMU 43 - 2*G*** FMU 43 - 2*H*** FMU 43 - 5*G*** FMU 43 - 5*H*** FMU 43 - 2*D*** FMU 43 - 2*F*** FMU 43 - 5*D*** FMU 43 - 5*F***
XA 175F
XA 176F
HART
XA 177F
XA 178F
If the devices are used in explosive areas, comply with all the specifications in these safety instructions.
Endress + Hauser
37
Prosonic M
The following control or installation drawings are supplied with the FM, CSA and TIIS-certified device versions:
Version Certificate Communication Housing Control- or Installation Drawing ZD 096F
FMU 40 - S*B*A* FMU 41 - S*B*A* FMU 40 - S*D*A* FMU 40 - S*F*A* FMU 41 - S*D*A* FMU 41 - S*F*A* FMU 40 - T***C* FMU 41 - T***C* FMU 40 - U*B*A* FMU 41 - U*B*A* FMU 40 - U*D*A* FMU 40 - U*F*A* FMU 41 - U*D*A* FMU 41 - U*F*A* FMU 40 - V***C* FMU 41 - V***C* FMU 40 - K***** FMU 41 - K*****
FM IS
HART
F12
FM IS
F12
ZD 097F
FM XP
T12
ZD 098F
CSA IS
HART
F12
ZD 088F
CSA IS
F12
ZD 099F
T12
ZD 100F
HART
F12
FMU 43 - M*****
FMU 43 - P*****
CSA DIP
38
Endress + Hauser
Prosonic M
Endress + Hauser
39
Prosonic M
Endress+Hauser GmbH+Co. Instruments International P.O. Box 2222 D-79574 Weil am Rhein Germany Tel. (07621) 975-02 Tx 773926 Fax (07621) 975 345 e-mail: info@ii.endress.com
Internet: http://www.endress.com
11.01