Académique Documents
Professionnel Documents
Culture Documents
CPD0811210CE
Notebook Computer
Model No.
CF-19KDRAXCM
This is the Service Manual for the following areas. M for U.S.A. and Canada
For U.K.
WARNING
Warnings This equipment is not designed for connection to an IT power system. (An IT system is a system having no direct connections between live parts and Earth; the exposed-conduciveparts of the electrical installation are earthed. An IT system is not permitted where the computer is directly connected to public supply systems in the U.K.) Disconnect the mains plug from the supply socket when the computer is not in use. This equipment is produced to BS800/1983.
Danger: The serviceman should not remove the cover of drive unit and should not service because the drive unit is a nonserviceable part. Please check DANGER label on PD-drive unit. Unplug the AC power cord to the equipment before opening the top cover of the drive. When the power switch it on, do not place your eyes close to the front panel door to look into the interior of the unit. LASER Specification Class 1 level LASER Product Wave Length: DVD 6588 nm CD 775~815 nm Laser safety information is appropriate only when drive with laser is installed.
SAFETY PRECAUTIONS
1. Before servicing, unplug the power cord to prevent an electric shock. 2. When replacing parts, use only manufacture's recommended components for safety. 3. Check the condition of the power cord. Replace if wear or damage is evident. 4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
LITHIUM BATTERY
This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service personel. Warning! A risk of explosion from incorrect installation or misapplication may possibly occur.
LITHIUM BATTERY
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type battery recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
LITHIUMBATTERIES
Vorsicht! Explosionsgefahr bei unsachgemem Austausch der Batterie. Ersatz nur durch denselben order einen vom Hersteller empfohlenen hnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
PILE AU LITHIUM
ATTENTION: IL Y A DANGER D'EXPLOSION S' IL Y A REMPLACEMENT INCORRECT DE LA PILE. REMPLACER UNIQUEMENT AVEC UNE PILE DU MME TYPE OU D'UN TYPE RECOMMAND PAR LE CONSTRUCTEUR. METTRE AU RBUT LES PILES USAGES CONFORMMENT AUX INSTRUCTIONS DU FABRICANT.
A lithium ion battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery. Lappareil que vous vous tes procur est aliment par une batterie au lithium-ion. Pour des renseignements sur le recyclage de la batterie, veuillez composer le 1-800-8-BATTERY.
F}). ( Reference Manual Battery Power) Once the allowable range requirement is satisfied, charging begins automatically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the temperature is 10 C {50 F} or below.) If the temperature is low, the operating time is shortened. Only use the computer within the allowable temperature range. The battery pack is a consumable item. If the amount of time the computer can be run by using a particular battery pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery pack should be replaced with a new one. When transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected. Always power off the computer when it is not in use. Leaving the computer on when the AC adaptor is not connected will exhaust the remaining battery capacity.
Appendix
Troubleshooting
The battery pack may become warm during recharging or normal use. This is completely normal. Recharging will not commence if internal temperature of the battery pack is outside of the allowable temperature range (0 C to 55 C {32 F to 131
Useful Information
Getting Started
CONTENTS
1. Specifications 2. Names and Functions of Parts 3. Block Diagram 4. Diagnosis Procedure 5. Power-On Self Test (Boot Check) 6. List of Error Codes <Only when the port replicator is connected> 7. Self Diagnosis Test 8. Wiring Connection Diagram 9. Disassembly/Reassembly 10. Exploded View 11. Replacement Parts List 1-1 2-1 3-1 4-1 5-1 6-1 7-1 8-1 9-1 10-1 11-1
1. Specifications
To check the model number: Check the bottom of the computer or the box the computer came in at the time of purchase. To check CPU speed, memory size and the hard disk drive (HDD) size: Run the Setup Utility ( Reference Manual Setup Utility) and select [Information] menu. [CPU Speed]: CPU speed, [System Memory]: Memory size, [Hard Disk]: Hard disk drive size cations
Model No. CPU Chipset Memory*1*2 Video Memory
*1*4*5
CF-19KDRAXJM
*1
CF-19KDRAXCM
Intel Core 2 Duo Processor SU9300 (1.20 GHz, 3 MB L2 cache, 800 MHz FSB) Mobile Intel GS45 Express Chipset 2048 MB (4096 MB Max.)*3 UMA 797 MB Max. (When Memory is 2 GB) / UMA 1551 MB Max. (When Memory is 4 GB) UMA 1024 MB Max.
Hard Disk Drive*5 Display Method Internal LCD*6 External Display Wireless LAN*8 Bluetooth LAN Modem Security Chip Card Slot PC Card ExpressCard
*11 TM *9 *7
160 GB 10.4 XGA type (TFT) 65,536/16,777,216 colors (800 600 dots/1024 768 dots) 65,536/16,777,216 colors (800 600 dots/1024 768 dots/1280 768 dots/1280 1024 dots) page 30 page 30 IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T Data: 56 kbps (V.92) FAX: 14.4 kbps TPM (TCG V1.2 compliant)*10 Type I or Type II x 1 (3.3 V: 400 mA, 5 V: 400 mA) ExpressCard/34 or ExpressCard/54 x 1 ISO7816 x 1
*13
x 1, Data transfer rate = 8 MB per second*14 200-pin, 1.8 V, SO-DIMM, DDR2 SDRAM, PC2-5300 Compliant*3 USB port (4-pin, USB 2.0) x 2, Serial Port (Dsub 9-pin male), Modem port (RJ-11), LAN port (RJ-45), External display port (Mini Dsub 15-pin female), Expansion Bus Connector (Dedicated 100-pin female), External Antenna Connector (Dedicated 50 coaxial connector) x 2, IEEE 1394a Interface Connector (4-pin x 1), Microphone Jack (Miniature jack, 3.5 DIA, Stereo), Headphone Jack (Miniature jack, 3.5 DIA, Impedance 32 , Output Power 4 mW x 2) 82 keys / Touch Pad / Dual Touch (Anti-Re- flection, Stylus (included) touch capable) AC adaptor or Battery pack Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 16.0 V DC, 3.75 A Li-ion 10.65 V, 5.7 Ah
Keyboard / Pointing Device Power Supply AC Adaptor*23 Battery Pack Operating Time Charging Time*15 Clock Battery Power Consumption*17 Physical Dimensions (W H D) (excluding the hand strap/shoulder strap) Weight (excluding the hand strap/shoulder strap)
*15
9 hours/ Approx. 6.5 hours Approx. 4.5 hours Coin type lithium battery 3.0 V
10.0 hours*16
Approx. 30 W*18 / Approx. 60 W (maximum when recharging in the ON state) 271 mm 49 mm 216 mm {10.7" 1.93" 8.5"} Approx. 2.30 kg {Approx. 5.06 lb.}
1-1
cations
Operation Environment Storage Environment Operating System Windows Vista Business Service Pack 1 Microsoft Windows XP Professional Service Pack 2 with Advanced Security Technologies (NTFS File System) Microsoft Windows XP Tablet PC Edition 2005 (NTFS File System) Utility Programs Adobe Reader, PC Information Viewer, Loupe Utility, Intel PROSet/Wireless Software*8, Bluetooth Stack for Windows by TOSHIBA*9, Wireless Switch Utility, Hotkey Settings, Professional Package*19, Power Saving Utility, Wireless Connection Disable Utility*19, Concealed Mode Utility*21 Setup Utility, Hard Disk Data Erase Utility*20, PC-Diagnostic Utility Temperature: 5 C to 35 C {41 F to 95 F} Humidity: 30% to 80% RH (No condensation) Temperature: -20 C to 60 C {-4 F to 140 F} Humidity: 30% to 90% RH (No condensation)
RF Frequency Band
1 MB = 1,048,576 bytes You can physically expand the memory up to 4096 MB, but the total amount of usable memory available will be less depending <Only for model with camera> The memory cannot be increased. A segment of the main memory is allotted automatically depending on the computers operating status. The size of the Video Memory cannot be set by the user. 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB. A 16,777,216 color display is achieved by using the dithering function. external displays. Only for model with wireless LAN Only for model with Bluetooth For information on TPM, (Start) and input c:\util\drivers\tpm\README.pdf in [Start Search] and click press Enter , and refer to the Installation Manual of Trusted Platform Module (TPM). click [start] - [Run] and input c:\util\drivers\tpm\README.pdf, and refer to the Installation Manual of Trusted Platform Module (TPM). Only for model with ExpressCard slot Only for model with Smart Card slot
*5 *6 *7 *8 *9 *10
*11 *12
1-2
*13
SD Memory Cards that support high-speed transfer rates can be used. supported.
to 8 GB. Operation on other SD equipment is not guaranteed. This computer is not compatible with MultiMediaCards. Do not insert this type of cards. Theoretical value and not the actual speed. The transfer rate does not become higher even if you use a card that supports the higher transfer rate. Varies depending on the usage conditions. Measured at LCD brightness: 60 cd/m2 Varies depending on the usage conditions, or when an external device is attached. Approx. 0.9 W when the battery pack is fully charged (or not being charged) and the computer is OFF. Rated power consumption 23-E-1 You need to install to use the feature. The Product Recovery DVD-ROM is required. Concealed Mode may not work properly during battery recalibration. It does not correspond to IEEE802.11a+b+g+n standards. Actual speeds may differ. <Only for North America> The AC adaptor is compatible with power sources up to 240 V AC adaptor. This computer is supplied with a 125 V AC compatible AC cord. 20-M-2-1
1-3
A: Wireless LAN Antenna <Only for model with wireless LAN> Reference Manual Wireless LAN B: Stylus/Digitizer pen Holder C: Touch Pad D: LED Indicator : Wireless ready This indicator lights when Wireless LAN, Bluetooth, and/or Wireless WAN are connected and ready. It does not necessarily indicate the On/Off condition of the wireless connection. Reference Manual Disabling/Enabling Wireless Communication : Wireless WAN status <Only for model with wireless WAN> Refer to the instruction manual of the wireless device. : Caps lock : Numeric key (NumLk) : Scroll lock (ScrLk) : Hard disk drive status E: Tablet Buttons Reference Manual Tablet Buttons F: LCD <Only for model with touchscreen> Reference Manual Touchscreen <Only for model with dual touch> Reference Manual Dual Touch
G: Bluetooth Antenna <Only for model with Bluetooth> Reference Manual Bluetooth H: Display Release Latch page 12 Switching to the Tablet mode I: Speaker Reference Manual Key Combinations J: Function Key Reference Manual Key Combinations K: Keyboard L: Hard Disk Drive Reference Manual Hard Disk Drive M: Battery Pack N: Power Switch O: LED Indicator : Battery status Reference Manual Battery Power : Power status (Off: Power off/Hibernation, Green: Power Sleep/ on, Blinking green: Standby, Blinking green rapidly: Cannot power on or resume due to low temperature.)
2-1
Left side
Rear side
Bottom
A: DC-IN Jack B: USB Port Reference Manual USB Devices C: IEEE 1394 Interface Connector Reference Manual IEEE 1394 Devices D: Modem Port Reference Manual Modem E: LAN Port Reference Manual LAN F: SD Memory Card Indicator (Blinking: During access) Reference Manual SD Memory Card G: SD Memory Card Slot Reference Manual SD Memory Card H: Wireless Switch Reference Manual Disabling/Enabling Wireless Communication I: <For model without Smart Card Slot> PC Card Slot (PC) Reference Manual PC Card / ExpressCard <For model with Smart Card Slot> Smart Card Slot (SCR) Reference Manual Smart Card J: <For model without Smart Card Slot> ExpressCard Slot (EX) Reference Manual PC Card / ExpressCard <For model with Smart Card Slot> PC Card Slot (PC) Reference Manual PC Card / ExpressCard K: Headphone Jack When they are connected, audio from the internal speakers is not heard. L: Microphone Jack A condenser microphone can be used. If other types of microphones are used, audio input may not be possible, or malfunctions may occur as a result.
When recording in stereo using a stereo microphone: (Start) - [Control Panel] - [Hardware and Click Sound] - [Sound] - [Recording] - [Microphone] [Properties], and then add a check mark for [No Audio Enhancements] in [Microphone Enhancements]. Click [start] - [All Programs] - [SoundMAX] - [Control Panel] and select [Microphone], and then add a check mark for [No Filtering] in [Microphone Enhancements]. When using a monaural microphone with a 2-terminal plug: (Start) - [Control Panel] - [Hardware and Click Sound] - [Sound] - [Recording] - [Microphone] [Properties], and then add a check mark for [Voice Enhancements] in [Microphone Enhancements]. Otherwise, only audio on the left track will be recorded. Click [start] - [All Programs] - [SoundMAX] - [Control Panel] and select [Microphone], and then add a check mark for [Voice Recording] in [Microphone Enhancements]. Otherwise, only audio on the left track will be recorded. M: Security Lock A Kensington cable can be connected. For further information, read the manual that comes with the cable. N: External Display Port Reference Manual External Display O: Serial Port P: RAM Module Slot <For model without Camera> Reference Manual RAM Module Q: External Antenna Connector R: Expansion Bus Connector Reference Manual Port Replicator / Car Mounter S: Camera <For model with Camera> Remove the protection seal on the camera before using the camera. Reference Manual Camera
2-2
int e l
For Santa Rosa Audio Board Processor side Bus 64bit 533MHz
Internal Graphics Interface 64bit BUS 1.8V 533MHz RJ11 Sound Data Modem MDC 1.5 Sigmatel AD1884 DRAM AMP
3 Block Diagram
Speaker
CRT SW
965-GM
INTEL
AC Link
I/O Board
CRT
CRT
PortRep
BIOS
8M AC-link Interface IDE Interface 1.5V PCI-E Bridge Interface Bridge DMI PCI
SATA HDD
80 / 120GB
SATA
2.5
(1.5Gb/s)
3-1
PCI-Express
INTEL
LPC Bridge ExpressCARD USB 2.0 Interface
USB
SPI
USB 2.0 x2
88E8055 MARVELL
RJ45 TYPE II
IEEE1394
Finger Touch Screen Super I/O SIO10N268 SMSC PR-PS/2 (KB& Mouse) KBD Mouse Buffer PortRep Int. KB LED BKLT Serial2 PortRep Serial1 Li-Ion Battery Pack Battery Charger HDD Heater
Digitizer
Serial 3
EC/KBC (M306KA)
Touch Pad
TPM 1.2
Configuration I/F
USB
GPS
HSDPA, EVDO
Bluetooth
Wireless Modem
2.0
antenna
antenna
antenna
RF Board
4 Diagnosis Procedure
4.1. Basic Procedures
4-1
4.2. Troubleshooting
Please take note of the following two points with regard to troubleshooting: 1. Know-how of diagnosis upon occurrence of heavy troubles, e.g. Set cannot be turned ON , Set fails to start , No display on screen , etc. 2. Explanation of each trouble, mainly symptom of trouble in operation.
Pay attention to the following points when in pursuit of the cause of a troubleshooting. 1. Peripheral apparatus connected with the set should all be removed before operation check. 2. Make sure that cables, boards, etc. are not coming off, and recheck the contact condition.
Set cannot be supplied with current. Power lamp fails to light up.
NG OK
Replace AC Adaptor/Battery
NO YES
Check contact condition of power input terminal. Replace if defective. Check Power SW. Replace if defective. Replace inverter board. Check inverter cable continuity. Replace if defective
Inverter board
NG OK
NO
YES
LCD unit check
NG
OK
Failure in starting BIOS operation check
NO
YES
Result of POST
NG OK
NG
OK
Return set-up utility setpoint to the state of delivery from factory .
Heavy trouble e.g., Set cannot be turned ON , Set fails to start , No display on screen , etc.
NO
HDD access
YES
Not displayed properly on screen. Main board check
Check HDD cable connection and continuity. Replace if defective. Replace HDD & Reinstall. Replace main board.
NG
OK
Some or all keys cannot be input. Make sure of contact of K/B connector in use. Replace keyboard or main board. Each kind of trouble in operation.
NO
Check if there are any flaws on CD media. Since flaws may appear on specific media, CD media can be defective.
YES
Replace main board. Starts but operates unstably. Reinstall HDD. Replace main board.
START END
4-2
5-1
6-1
02D0 System cache error - Cache disabled Contact Panasonic Technical Support. 02F0: CPU ID: CPU socket number for Multi-Processor error. 02F4: EISA CMOS not writable ServerBIOS2 test error: Cannot write to EISA CMOS. 02F5: DMA Test Failed ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers. 02F6: Software NMI Failed ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt). 02F7: Fail - Safe Timer NMI Failed ServerBIOS2 test error: Fail-Safe Timer takes too long. device address Conflict Address conflict for specified device. Allocation Error for: device Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device. Failing Bits : nnnn The hex number nnnn is a map of the bits at the RAM address which failed the memory test. Each 1 (one) in the map indicates a failed bit. See error 230,231 or 232 for offset address of the failure in System, Extended or Shadow memory. Invalid System Configuration Data Problem with NVRAM (CMOS) data. I/O device IRQ conflict I/O device IRQ conflict error. Operating System not found Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed disk and drive A: are properly identified. Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. Parity is a method for checking errors in binary data. A parity error indicates that some data has been corrupted. Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. Press <F1> to resume, <F2> to Setup Displayed after any recoverable error message. Press <F1> to start the boot process or <F2> to enter a Setup and change the settings. Write down and follow the information shown on the screen.
6-2
Troubleshooting
3. All devices which can select the enhancing test make the setting of the enhancing test possible. 4. The district device is made"FULL" display (enhancing test). 5. The test begins clicking . *Please refer to item 4 for the error result of each test and the division of the breakdown part.
7-1
-As for the device under the diagnosis, blue and yellow are alternately displayed at the left of the icon. - The diagnosis result of the device greens at the left of the icon when it is normal, and becomes red when abnormal.
-When the test of all devices ends, the test result is displayed under the right of the screen.
-Please click while diagnosing when being stop on the way by the time the test of all devices ends. -Please click when you restart "PC-Diagnostic utility". *Each device is tested from the beginning, and it is not possible to restart on the way. -When the test of all devices ends, the test result is displayed under the right of the screen.
7-2
Do not test
2-3. The content of the setup is returned to the setting of the user
1. Turned on the computer. 2. "F2" is pushed on the screen while "Press<F2>to enter Setup" is displayed of "Panasonic". 3. Push "F10", and on the screen of "Is the change in the setting preserved and do end?"and then "Yes" is selected, and "Enter" is pushed. 4. The computer reactivates automatically. 5. The end option is chosen by the start menu, and the power supply of the computer is turned off. Standard at test time All devices other than RAM and HDD ---------- about 1 minute RAM standard test ----------------------------------- 1 - 2 minutes HDD standard test ----------------------------------- 2 - 3 minutes HDD enhancing test (60GB) ---------------------- about 40 minutes Ex.The standard when the standard <all device> is tested becomes 1+2+3=6 minutes. There is greatly a difference from RAM test when the memory is increased according to the performance of the memory occasionally. Moreover, when the main body of PC under the test is a high temperature, it occasionally takes time. There is greatly a difference from HDD according to the performance of the drive occasionally.
7-3
RAM
HDD
MODEM
Wireless LAN
Sound *5
USB
*1
It is confirmed not to find abnormalityin the wiring between the USB controller and the connector by confirming the connection of the USB equipment connected with the USB connector. It is confirmed not to find abnormalityin the wiring between the controller and the connector by connecting to HUB with LAN cable.
Mainboard / Connector
LAN
*2
Mainboard / Connector
PC Card SD *3
It is confirmed not to find abnormality in the CardBus controller. It is confirmed not to find abnormality in the SD controller. It is confirmed not to find abnormality in keyboard controller's keyboard interface. Whether keyboard controller's mouse interface operates normally is confirmed. The drive is normally reset, and it is accessible is confirmed. The key is actually input, and the operation is displayed on the screen. The operation is actually displayed on the screen by operating the touch pad. It is confirmed to be able to read media normally.
Keyboard
Touch Pad
*4
DVD-ROM
*6
7-4
Test Item
Standard Enhanced
Content of Standard Test It is confirmed not to find abnormality in the USB connection of Touch Screen. This test cannot find abnormality of Touch Screen. It is confirmed not to find abnormality in the connection of Main board and Bluetooth module. It is confirmed not to find abnormality in the connection of Main board and Wireless WAN module. It is confirmed not to find abnormality in the legacy FD drive. This test cannot find abnormality of mechanical breakdown. (e.g.. Head, Motor) It is confirmed not to find abnormality in access to VRAM with VESA. The PC which uses main memory as VRAM may fail with main memory failure. It is confirmed not to find abnormality in the connection of Main board and GPS It is confirmed not to find abnormality in the IEEE1394 controller.
Content of Extend Test Perform Touch Screen functionality practically. Operator has to judge PASS/FAIL with test result.
Touch Screen
Bluetooth
Bluetooth cable
Wireless WAN
WWAN cable
Floppy
FD Drive/ Main board (Super I/O)/ FDD cable FDD connector Main board (Chipset, Graphic Controller)/ Memory GPS cable Main board (IEEE #394 Controller) It is confirmed not to find abnormality in the wiring between Chipset and Express Card. Main board (Chipset)/ Express Card Connector Main board (Smart Card Controller) It is confirmed not to find abnormality in the wiring between Super I/O and Serial Connector. This test cannot find failure of cable characteristic and device problems. It is confirmed not to find abnormality in the wiring between Super I/O and Parallel Connector. This test cannot find failure of cable characteristic and device problems.
Video
GPS IEEE1394
Express Card It is confirmed not to find abnormality in the Smart Card controller. It is confirmed not to find abnormality of Super I/O UART function. This test cannot find lack of wiring between Super I/O and Serial Connector. It is confirmed not to find abnormality of Super I/O parallel function. This test cannot find lack of wiring between Super I/O and Parallel Connector.
Smart Card
Serial Port
*7
Parallel Port
*8
*1 *2 *3 *4 *5
Please connect the USB device with the port (USB connector) which wants to test before the tests. Please connect LAN port with LAN HUB with LAN cable before the tests. The operator actually inputs the key, and the operator judges PASS/FAIL of the test. The operator actually operates the mouse, and the operator judges PASS/FAIL of the test. It is not abnormal though the sound is emitted from the speaker while testing. When the test result is PASS, trouble is thought by not hearing of the sound under the test from the speaker and the headphone by the wiring of the audio output system. *6 Please set DVD/CD media in the drive before the tests. *7 Please set a Special Loop Back Connector Tool at serial connector for Enhanced Test. (This Connector Tool is same as the one used before.) *8 Please set a Special Loop Back Connector Tool at parallel connector for Enhanced Test. (This Connector Tools is same as the one used before.)
7-5
HSDPA PCB
I/F PCB
CN851
H/P
MIC
JK962 JK963 JK960 JK961 CN16 CN9 CN18 CN25 CN6 CN14
CN901
CN27
AUDIO PCB
CN3
CN24
CN22
KEYBOARD
CN17 CN8 CN5
COIN BATTERY
MAIN PCB
CN12 CN21 CN11
LAN PORT
CN882
HDD
CN4
DIMM
WIRELESS MODULE
J1 CN15
CN23
PAD PCB
CN801 CN804
TOUCH PAD
CN800
CN807 CN805
CN802
SW PCB
CN950
8-1
9 Disassembly/Reassembly
Note: Power off the computer. Do not shut down to the Suspend or hibernation mode. Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.
9.1.
9.1.1.
Disassembly Instructions
Disassembly Flowchart
The chart below shows the various parts which should be removed in order to remove the parts that are to be replaced. Parts can be replaced efficiently be following the disassemblysteps in the chart.
9.1.2. Preparation
9.1.3. Battery Pack and HDD Pack 9.1.4. Touch Pad and Keyboard 9.1.5. DIMM Lid Ass'y 9.1.6. Rear Cabinet 9.1.8. HSDPA PCB and Bluetooth PCB 9.1.7. DU Lid Unit 9.1.20. Each Cover
9.1.10. Main PCB, Wireless Module, SD PCB, Antenna PCB and Modem PCB 9.1.11. I/O PCB Ass'y 9.1.12. Power SW PCB 9.1.13. left LED and right LED PCB
9.1.16. LCD Rear Case 9.1.19. WWAN Main Antenna PCB, LAN-Main BT Antenna PCB, LAN AUX Antenna PCB and WWAN AUX Antenna PCB
9-1
9.1.2.
Preparation
Before disassembling, be sure to make the following preparations. Shut down Windows and turn off the power. Disconnect the AC adaptor. Remove the optional DIMM memory card and PCMCIA card if they are connected. Remove other devices if they are connected. Attention: Please execute writing BIOS ID when you exchange the Main Board. Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.
HDD Case B
Hooks
Heater
<N13> <N13>
9.1.3.
HDD Case A 1 2 3
5. Remove the two Screws <N13>. 6. Remove the HDD Case A and the HDD Case B. 7. Remove the HDD Screws <N13> : DXQT2+D4FNL
9.1.4.
1. 2. 3. 4.
Open the Battery Cover. Remove the Battery Pack. Open the HDD Cover. Remove the HDD Pack.
1. Remove the Palm Rest Ass'y. Note: The Palm Rest Ass'y is firmly fixed with two-sided tape. Carefully remove the Palm Top Cover Sheet not to damage it. 2. Remove the 4 Screws <N9>. 3. Remove the KBD Plate.
9-2
7. 8. 9. 10. 11.
1
Disconnect the Cable from Connector (CN18). Remove the Keyboard. Remove the TP Tape. Disconnect the Cable from Connector (CN800). Remove the Touch Pad and Click Button Plate.
9.1.5.
4. Lift the far side of the Keyboard and slide it to backward, and then turn the Keyboard over frontward.
<N1>
1. Remove the 4 Screws <K14-8>. 2. Remove the DIMM Lid Ass'y. Screws <K14-8> : DRHM5025YAT
9.1.6.
<N10>
1. Remove the 13 Screws <N10>. 2. Open the LID Rubbers. 3. Remove the Rear Cabinet. Screws <N10> : DRHM0061ZA
Connector (CN800)
Connector (CN18)
9-3
9.1.7.
<N19>
1. Remove the 7 Screws <K14-9>. 2. Remove the DU Lid Angle and DU Lid. Screws <K14-9> : DXQT2+D25FNL
9.1.8.
6. 7. 8. 9. 10. 11.
Disconnect the Antenna Cable from the Clamper. Disconnect the Antenna Cable. Remove the 4 Screws. <N19> Disconnect the Cable from the Connector (CN604). Remove the 2 Screws. <N19> Disconnect the Cable from the Connector (CN1) and remove the Bluetooth PCB and HSDPA PCB.
9.1.9.
1. 2. 3. 4. 5.
Remove the Cable Holder Cushion. Disconnect the 2 Antenna Cables (brown, black). Remove the Tape. Remove the 4 Screws. <N9> Disconnect the Cable from the Connector (CN600).
1. Remove the 3 Screws <N9>. 2. Disconnect the Cable from a Connector (CN901). 3. Remove the Audio PCB. Screws <N9>:DRSB2+5FKL
9-4
9.1.10. Removing the Main PCB, Wireless Module, SD PCB, Antenna PCB and Modem PCB
Connector(CN17)
Note: This procedure is not necessary if the computer is not equipped with Wireless Module or Modem PCB. 1. Disconnect the 2 LCD Cables. (CN8,CN17)
<N3> DU PCB <N3> <N9> <N9> <N9> Antenna PCB <N3> <N3> Plate
Connector(CN15)
5. Remove the 2 Screws <N8>, and remove the HDD Connector Guide. 6. Remove the 2 Screws. <N9> 7. Disconnect the Cable from the Connector. (CN15) 8. Remove the BAT FPC Ass'y. 9. Remove the 3 Screws. <N19> 10. Disconnect the Cable from the Connector (CN21), and remove the SD PCB Ass'y.
DIMM Holder Wireless Module <N19> <N19> <N19> <N19> <N19> <N19>
2. Remove the gray, black and white Antenna Cables. 3. Remove the 2 Screws <N3> and the 3 Screws <N9>. 4. Remove the 2 screws <N3>, and remove the DU PCB, Plate and Antenna PCB.
Coin Battery
11. Disconnect the Cable from the Connector (CN3), and remove the Coin Battery.
9-5
12. Remove the 2 Screws <N19>, and remove the Wireless Module. 13. Remove the 2 Screws <N19>, and remove the Modem PCB. 14. Remove the 2 Screws <N19>, and remove the DIMM Holder.
Tape <N19> <N19> <N19> <N19> Connector(CN9) Connector(CN14) <N19>
9.1.11.
Connector(CN23)
1. Remove the 4 D-SUB Screws <N2>. 2. Remove the 2 Screws <N9>. 3. Remove the I/O PCB Ass'y. Screws <N2> : DFHE5058ZB Screws <N9> : DRSB2+5FKL
15. Remove the Tape. 16. Disconnect the 3 Cables from the 3 Connectors. (CN9,CN14,CN23) 17. Remove the 7 Screws <N19>, and remove the Main PCB and Combo Socket. Screws <N3> : DFHE5108ZA Screws <N8> : DRSB2+10FKL Screws <N9> : DRSB2+5FKL Screws <N19> : XSB2+3FNL
1. Remove the Screw <N1>. 2. Disconnect the Cable from the Connector (CN9). 3. Remove the Power SW PCB. Screw <N1> : DFHE5025XA
9-6
Operation Sheet
1. 2. 3. 4. 5.
Remove the two Release Papers. Disconnect the Cable from the Connector (CN806). Remove the left LED PCB. Disconnect the Cable from the Connector (CN801). Remove the right LED PCB.
Pad PCB
<N9>
Hinge Cover
<N9>
1. Disconnect the 2 Cables from the 2 Connectors (CN805,CN807). 2. Remove the 4 Screws <N1>. 3. Remove the Pad PCB.
9-7
Screws <N4> : DRHM5054XA Screws <N7> : DRQT26+E5FKL Screws <N15> : DXYN2+J6FNL Screws <N16> : DXYN3+J10FNL
4. Remove the 4 Screws <N18>. 5. Turn the computer over. 6. Remove the Display Unit. Screws <N1> : DFHE5025XA Screws <N9> : DRSB2+5FKL Screws <N18> : DXYN4+J7FNL
1. Remove the Cable Holder. 2. Remove the 2 Screws <N17>. 3. Remove the Cable Holder Plate and LCD Hinge. Screws <N17> : DXYN3+J8FNL
9.1.18. Removing LED PCB, LCD Module, Digitizer and LCD Unit
Sheet Sheet <E36-15> LED PCB Tape <E36-15>
<N7>
<N7> <N7> <N7> <N4> <N7> <N7> <N4> Tablet Latch Cover <N7> <N7> <N7>
1. Remove the 6 Screws <N7> on the front side of Display unit. 2. Remove the 6 Screws <N7> on the back side of Display unit. 3. Remove the 2 Screws <N4> on the top side of Display unit. 4. Remove 2 Antenna Covers and Tablet Latch Cover. 5. Remove the 10 Screws <N15>. 6. Remove the 2 Screws <N16>. 7. Remove the LCD Rear Case.
LED Module
2. 3. 4. 5. 6.
Disconnect the 4 Cables from 4 Connectors. Remove the 2 Screws <E36-15>. Remove the LCD Back Plate and LCD PCB. Remove the Digitizer. Remove the LCD unit., then remove the LED Plate Holder and LED module.
9.1.19. Removing WWAN Main Antenna PCB, LAN-Main BT Antenna PCB, LAN AUX Antenna PCB and WWAN AUX Antenna PCB
WLAN-Main BT Antenna PCB WWAN Main Antenna PCB <N1> Pen <K10-1-13> <K10-1-13> <N1> <N1> Pen Holder WLAN Aux Antenna PCB
Battery LID ASSY HDD LID ASSY Audio LID Rubber USB Back Rubber RGB LID Rubber
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Remove the 1 Screws <N1>. Remove the WWAN Main Antenna PCB. Remove the 2 Screws <N1>. Remove the WLAN-Main BT Antenna PCB. Remove the 1 Screws <N1>. Remove the WWAN AUX Antenna PCB. Remove the 2 Screws <N1>. Remove the WLAN AUX Antenna PCB. Remove the Pen Remove the two Screws <K10-1-13>. Remove the Pen Holder.
1. Remove the 14 Screws <N6>. 2. Remove the Modem/LAN LID Rubber, LAN LID Rubber, USB LID Rubber, DC IN LID Rubber, Serial LID Rubber, RGB LID Rubber, Audio LID Rubber and USB Back Rubber. 3. Remove the Rear Cabinet. (Refer to 7.1.5 Removing the Rear Cabinet) 4. Remove the 6 Screws <K12-16>. 5. Remove the Battery LID ASS'Y, HDD LID Ass'y and PCMCIA LID Ass'y. Screws <K12-16> : DRQT26+D3FKL Screws <N6> : DRHM5025YA
9-9
9.2.
9.2.1.
Reassembly Instructions
Attention when CF-19 series is repaired
Please execute writing BIOS ID when you exchange the Main Board. Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.
9.2.2.
1. 2. 3. 4. 5. 6.
Setting up the LED PCB, LCD Module, Digitizer and LCD Unit.
Sheet Sheet <E36-15> LED PCB Tape <E36-15> LCD Back Plate
Set the LED Module to the LCD UNIT. Set the LED Plate Holder to the LED Module. Set the LCD UNIT to the LCD Front Cabinet/TS Panel. Set the Digitizer to the LCD UNIT Fix the LCD Back Plate using the 2 Screws.<E36-15> Set the LED PCB to the LCD Back Plate, and connect the 4 Cables to the Connectors. 7. Paste 2 Sheets and tape.
LED Module
Screw
LED PCB ASSY Remove the Release Paper on the back side and attach it. TS PCB ASSY
0~0.5mm
Screw
Fit to the bottom edge of Plate. 0~1mm Fit to the Frame edge. 0~0.5mm
Screw
Screw
Screw the Board and the Spacer together.
9-10
LED PCB LED PCB Sheet LCD Back Cushion DA LED PCB ASSY
Match to the center from right and left to attach ( 1 mm).
Digitizer ASSY
<Note> *Paste Sheets firmly. 20~30N(2.0~3.0Kgf) <Order of fixing screws> 0~1mm After inserting the connector, slide the hook to lock
Screw
Screw
Paste Tape
Screw
Screw the Board and the Spacer together.
LCD BACK Cushion LCD Side Cushion Lower LCD Side Cushion Lower
LED PCB
3mm
0.5mm
Attachment Standard
Tape Paste Tape after set the LED PCB,LED Plate Holder
9-11
LCD DA ASSY
PET TAPE
Ensure the edge of the conductive fabric is not frayed to avoid short circuit with the Board. 1~2 mm
Attach it on the Connector. Insert into the Connector. Insert between the ribs.
Shield Sheet
Pasted on the connectorafter it is wound around the cable twice.
LCD Cable TS
Avoid any stress on the TAB part of the LCD Module because the line may come off.
Insert into the Connector. Pass the LCD Cable as below. Attach the Tape as below. Fold the Tape as below to attach.
PET Tape
Corner 1mm *Avoid running over the waterproof rib of the LCD Front.
T/S NG
Laminate Dimensional tolerance: 0.2
TS FPC Sheet
Match to the edge of TS FPC to attach (0 - 0.5 mm).
T/S
Attach to the center of the display surface. (Use the special attaching machine.)
1mm
1mm
TS Spacer B
Be free of overhang..
TS Spacer B
1mm
TS Spacer A
0 1mm
9-12
DIGITIZER ASSY
0~1mm 0~1mm
1~2mm 1~2mm
0~1mm
0~1mm
Cushion Sheet
Cushion
Digitizer
0~1mm 0~1mm
DIGITIZER ASSY
Sheet
Remove the maker attaching sheet (white, variant type) and attach Sheet.
Detail of "A"
A B
Detail of "B"
9.2.3.
Assembling the WWAN Main Antenna PCB, LAN-Main BT Antenna PCB, LAN AUX Antenna PCB, WWAN AUX Antenna PCB and Pen holder
1. Fix the Pen Holder using the 2 Screws. <K10-1-13> 2. Attach the Pen. 3. Fix the WWAN AUX Antenna PCB using the 2 Screws. <N1> 4. Fix the LAN AUX Antenna PCB using the 2 Screws. <N1> 5. Fix the LAN-Main BT Antenna PCB using the 2 Screws. <N1> 6. Fix the WWAN Main Antenna PCB using the 2 Screws. <N1> Screws <N1> : DFHE5025XA Screws <K10-1-13> : DRHM5025YAT
Pen
<N1>
9-13
CAUTION
<Note> Avoid any stress on the solder.
Detail of "A"
S2 Detail of "B"
Avoid running over the rib, boss and bin to avoid catching the Cable when LCD Rear is set.
A
Wrap around the ANT Cable and insert between the ribs.
The cushion must come within 2mm from the center of the rib.
S2
Insert into the Front rib after wrapping.
S2
Avoid overlapping of the Cable at right and left of the hook as below. Put the Cable on each hook. Put the Cable on each hook.
9.2.4.
1. Wind the Cable coming out of the LCD Unit counterclockwise to the LCD Hinge. 2. Set the Lock Plate and the Hinge Top Cover, and rotate the LCD Hinge to turn the Display Unit to front 3. Put the LCD Cable and the Antenna Cable in the Cable Holder. 4. Fit another Cable Holder and clamp the Cable Holders in the LCD Hinge. 5. Fix the LCD Hinge using the 2 Screws <N17> and the 2 Cable Holder Plates. Screws <N17 > : DXYN3+J8FNL
9-14
CAUTION
If attached reversely, the direction of cutting edge faces the Cable and this may damage the Cable. Be careful of the direction.
S3
Initial condition of LCD Hinge. Ensure the "C" side comes to the lower right corner when viewing from above.
Screw
0.08N m(
Step1
Step3
Step5
The position of the Antenna cables: Black/White/Blue/Gray/Brown or Green (From the left)
Lock Spring
Install the Lock Springs on the Hinge as shown in figure.
Step2
Step4
Fit the Holder to the Hinge Cover after inserting cables into the Cable Holder as shown in figure.
9-15
9.2.5.
Assembling the Antenna Cover, the Tablet Latch Cover and the LCD Rear Case
<N15> <N15> <N15> <N15> <N15> <N16> LCD Rear Case <N16> <N15> <N15> <N15> <N15> <N15>
1. Fix the LCD Rear Case using the 10 Screws <N15> and the 2 Screws. <N16> 2. Attach the Antenna Covers and the Tablet Latch Cover to the Display Unit. 3. Tighten the 8 Screws <N7> on the back of the Display Unit. 4. Turn the Display Unit over, and tighten the 8 Screws. <N7> Screws <N7> : DRQT26+E5FKL Screws <N15> : DXYN2+J6FNL Screws <N16> : DXYN3+J10FNL
<N7>
<N7> <N7> <N7> N4> <N7> <N7> <N4> Tablet Latch Cover <N7> <N7> <N7>
Magnet Cushion
Don't get onto a step. Attach this side to the Cabinet after attaching.
Magnet
Tape
Don't get into a LCD indication range. Attach and apply the load 30~40N (3.0~4.0 Kgf).
9-16
LCD Cushion 3
Panasonic Badge
LCD Cushion 1
0~1mm
LCD Cushion 2
01mm
PET Sheet
01mm
ANT Cover
ANT Cover
Screw (N16) Places of tighten a screws Screw (N15) Screw (N7) 10 Places 12 Places
in numerical order (same the frontside) Don't forget fixing with screws
Screw (N16)
of of of of
(N15) :0.5 0.02N m( 5.0 0.2kgf cm) (N7) :0.4 0.02N m( 4.0 0.2kgf cm) (N4) :0.5 0.02N m( 5.0 0.2kgf cm) (N16) :0.8 0.08N m( 8.0 0.8kgf cm)
9-17
9.2.6.
1. Fix the Display Unit using the 2 Screws <N9>. 2. Close the Display Unit and turn the computer over, then fix the Display Unit using the 4 Screws <N18>.
3. Turn the computer over and fix the LCD Hinge Cover using the 2 Screws <N1>.
<N9>
Hinge Cover
<N9>
4. Open the Display Unit and fix the LCD Hinge Cover using the 2 Screws <N1>. Screws <N1> : DFHE5025XA Screws <N9> : DRSB2+5FKL Screws <N18> : XYN4+J7FNL
<N1> <N1>
<N1> <N1>
9-18
Screw
Pass the Cable through the groove of cushion Caution: Running over affects waterproof performance.
Black / White
Blue / Glay
Green
Close the LCD with the Hinge hooked on the Top Case, and then fold back.
LCD Unit
Set to the Top Case Ass'y Insert all of antenna cables into the notch of the board.
9.2.7.
1. Attach both the SW PCB and the Operation Sheet to the Cabinet.
SW PCB
Operation Sheet
2. Connect the 3 Cables to the 3 Connectors. (CN800,CN805,CN807) 3. Fix the Pad PCB using the 4 Screws. <N1> Note: Tighten the Screws in the numbered order (No1 to No4). Screws <N1> : DFHE5025XA
9-19
SW FPC Insert
LED(R) FPC PAD MAIN FPC ASSY No direction when inserting Back side Insert Power SW Cable Insert
Power Cable Cushion Wrap around the Cable. Use the fixing JIG for stressed parts when inserting. 8 2mm
SW PCB Ass'y Operation Tape Match the edge and attach it. 0 1mm SW PCB Ensure the LED part does not come off or run over. Operation Sheet Confirm the direction when attaching. Confirm the direction when attaching. CN bracket is on the back side.
Fold back
0 Tape
1mm
SW PCB Ass'y
Match to the upper left corner. 0 to 0.5mm
Screw
Screw
9.2.8.
1. 2. 3. 4. 5. 6.
Connect the Cable to the Connector. (CN806) Fix the left LED PCB. Connect the Cable to the Connector. (CN801) Fix the right LED PCB. Attach the two Release Papers. Attach the Palm Rest Ass'y.
9-20
LED Light Guide Sheet(R) LED Light Guide Sheet(L) LED PCB(L) LED PCB(R)
Match the edge and attach it. Avoid running over the LED. Back side
0 3mm
9.2.9.
1. Connect the Cable to the Connector. (CN9) 2. Fix the Power SW PCB using the Screw. <N1> Screws <N1> : DFHE5025XA
cm)
Keep the space of 1 mm between the Top Case and the rib.
Gasket
S2
Avoid catching the Cable between the Board and boss.
Spring
Insert into the Knob and Pin on the Top Case.
No Screw Necessary
Process the center part as illustrated. Avoid any stress on the bottom part of the stiffening plate during this work. (If stress is placed, load is applied on the coating part and connection failure may occur.)
Screw Screw
Note
Screw
CAUTION
9-21
9.2.11.
Setting the Main PCB, Wireless Module, SD PCB, DU PCB, Antenna PCB and Modem PCB
Tape <N19> :No5 <N19> Tape Connector(CN9) Connector(CN14) <N19> :No7
1. Fix the Main PCB using the 7 Screws <N9>. 2. Connect the 3 Cables to the 3 Connectors. (CN9,CN14,CN23) 3. Attach the Tape.
Connector(CN23)
9-22
4. 5. 6. 7.
Fix the Modem PCB using the 2 Screws <N19>. Fix the Wireless Module using the 2 Screws <N19>. Fix the DIMM Holder using the 2 Screws <N19>. Attach the Cable to the Connector (CN3) and attach the Coin Battery.
<N19> <N19>
Coin Battery
8. Fix the SD PCB Ass'y using the 3 Screws <N19>. 9. Attach the Cable to the Connector (CN21). 10. Hook the Flex Cable on the DIMM Holder, and turn 90 degrees. 11. Fix the BAT FPC Ass'y using the 2 Screws <N9>. 12. Connect the cable to the Connector. (CN15) 13. Fix the HDD Connector Guide using the 2 Screws <N8>.
Connector(CN15)
9-23
14. Fix the DU PCB and the Plate using the 2 screws <N3>. 15. Fix the DU PCB Ass'y and Antenna PCB using the 3 screws <N9> and the 2 screws <N3> . 16. Connect the white, black and gray Cables.
Antenna PCB
white cable
black cable
gray cable
17. Turn the computer over, open the Display Unit, and then connect the 2 LCD Cables. (CN8,CN17) Note: Tighten the Screws in the numbered order (No1 to No7). Screws <N3> : DFHE5108ZA Screws <N8> : DRSB2+10FKL Screws <N9> : DRSB2+5FKL Screws <N19> : XSB2+3FNL
Connector(CN8)
Connector(CN17)
9-24
Insert
Tape
0~1mm
Fold back.
Apply the lubricant (sub material) on the HDD Connector for about 1 second.
(Note for spraying around when applying.)
Thermal Sheet
Thermal Sheet
Attach to the center of Module.
Round to make the brown side outside and insert the notch.
S4
Wireless Module
Places of tighten a screws Screw (N9) Screw (N19) 8 Places 2 Places 0.02N m( 2.0 0.2kgf cm)
Insert and then lock.
Pass the Cable through the cavity part of Holder. Note S2 Avoid catching between the connector and Holder or running over the top.
SD PCB Ass'y
Insert the FPC into the Main Board. Ensure that the Knob is fit to SW when attaching.
DIMM Holder Ass'y RF SW Knob Places of tighten a screws Screw (N8) Screw (N19) 2 Places 5 Places DIMM Holder
9-25
0~0.5mm
0~0.5mm
EX PC
0~0.5mm
Attach it fitting to the left. Ensure that both top and bottom are hooked.
0~0.5mm
Screw
D Blind Sheet S
Apply the load to attach. 20~30N (2.0~3.0Kgf)
2.0 0.2kgfcm)
9-26
6. 7. 8. 9. 10.
Connect the Cable to the Connector. (CN600) Fix the RF PCB Ass'y using the 4 Screws. <N9> Attach the Tape. Attach the brown and black Antenna Cables. Attach the Cable Holder Cushion.
Tape <N9> <N9> <N9> <N9> HSDPA PCB Antenna Cable(brown) Antenna Cable(black)
9-27
CAUTION
Cables processed Step 3 Confirm thethe Board, and thenin Step 5 do not exist under fix the Screws.
S2
This is because Cable catching may occur between the Board and boss.
Screw Screw
Arrange all the cables (white, black, blue, gray and green) to the arrow direction.
Step 7
Process the additional Cable (gray). Attach the cushion to the side of rib.
Step 5 Cable(White-L)
Tape
Cable (Black)
After processing the cables, inserting the FPC and locking, incline the Audio PCB to the arrow direction.
Step 8
Cable(Gray-S)
Process the additional Cables (white and black). *Pass all the Cables through under the Cushion attached in Step 3. Connect the gray antenna cable.
Step 9
Connect the blue antenna cable.
Step 13 S2
Insert into the Clamper. If poorly fixed, the Cable catching may occur between the Board and boss.
Cable
9-28
9-29
CAUTION
0.5 mm
0~1mm
0~1mm
0~1mm
0~1mm
01mm
01mm
Gasket
Match to the marking line and attach.
Bottom Rubber
Rated Label
S2
Note for attachment Avoid running over the frame. Avoid air leaking into it.
9-30
Keyboard
5. Connect the Cable of the Keyboard to the Connector (CN18) on the Main PCB. 6. Fix the KBD Connector Cover using the three Screws. <N1>
<N1>
9-31
Gasket E
Fit to the wall of the end side, and put the surplus to the Cabinet side. 0~0.5mm
Avoid running over the rib. Attaching details of Tape Fit to the rib. 0~1mm Fold. 3~5mm 0~0.5mm
0~0.5mm 0~0.5mm
Attach to the rib. Fold over the front and attach it.
0.5~1.5mm
TP Tape
Attach it using the jig.
CAUTION
Gasket
KB CNT LID
Confirm the LCD Rear side is at front when processing the wire.
Screw Screw
Rotate the LCD to make the LCD display face front after setting the KBD. Tighten inside first.
Screw Screw
Tighten inside first.
KBD Plate(L)
Screw Screw
Before attaching 2 and 3, press the two-sided tape parts (4 positions). :30N(3.0Kgf)
KBD Plate(R)
KBD Ass'y
Lock the connector after inserting FFC. Set using the jig.
2.0 0.2kgfcm)
9-32
Intel Label
4~6mm
Remove the Release Paper, and then attach the Palmrest Ass'y.
Remove the two-sided tape on the back side and attach it. After attaching, press by the load 30 to 40N (3.0 to 4.0 Kgf). Palmrest Ass'y
Keyboard
Ensure the direction is right.
KBD Tape
0 ~ 2 mm from the notch bottom edge
9-33
Heater
<N13> <N13>
HDD Case A
2. Open the HDD Cover and set the HDD Pack. 3. Open the Battery Cover and set the Battery. Screws <N13> : DXQT2+D4FNL
1 2 3
9-34
CAUTION
Insulation Parts
Insulation Parts
51mm
Heater Ass'y
51mm
HDD S4 Heater
Ford back between 2~5mm Inserted into pins Round to make the brown side outside and insert the notch.
FPC(HDD)
1~2mm
Thermal Sheet
Revision Label
Attach to the inner side of HDD Case A.
HDD Damper
Remove the Release Paper.
Attach.
0.02N
m(
2.0
0.2kgf
cm)
9-35
DC IN LID Rubber USB LID Rubber LAN LID Rubber Moden/LAN LID Rubber <N6> <N6> <N6> :No.13:No.12 <N6> :No.14 :No.11 <N6> <K12-16> <K12-16> :No.10 <K12-16> <K12-16>
Battery LID ASSY HDD LID ASSY Audio LID Rubber USB Back Rubber RGB LID Rubber
9-36
10 Exploded View
K82
A N9
K81 K3-3 K3-5 K3-4 K83 K3 E24 K30
A N9 A N9
K31 K3-6 K3-1 K3-2 K163 A N1 K144 K144 K144 K144 K9 K70
A N1
K115 K114
A N1
K107
K113 K100
K5
K110
K1603
F N11
K1604
K80
K80-1
A K80-12
K80-10 K80-4
K80-3
K80-2
CF-19KDRAXCM
K12-15-5 K12-15-3
F K12-15-10
K12
B
K12-15-1
B K12-16
K12-15-7
A K12-15-9
K12-18
K12-14-7
K12-14-1
B
K12-15
K12-14-10
K12-14-3
B K12-16
K12-14-5
B K12-14-10
K117
K12-21
K12-21
K12-14
A N1
E5
K108 K13-3
K12-6
K13
A K12-13-11 A K12-13-9
K12-13
K13-5 K13-4
E N18
K12-13-8
A K12-13-9
K12-13-2
K12-19
K12-13-7 K12-13-1
B K12-13-10
K13-2 K13-7
C K12-17
K12-13-1
B K12-16 B K12-13-10
B K12-16
K12-13-5
K12-13-4
CF-19KDRAXCM
K54
K99
K214
A N19 E1 A
N19
A N9
N19 K87
N19
K211 K38
K54
N9
E401 E405
A N19 A N19
K51
E33
A N19
E2 E21
A N9
E404 E28
K96
E9 E403
A N19
A N3
E10 K33
A A N1
K48
A N9
A N9
K37 E7
N9
A N9 A N3
K132
E20
A
N1 K164
A N1
K126
N9
A N9 A N5 A N5
A N1 A N1
K165
A N1
K22
K43
E409
E31 K42
A N1
A 0.2 0.02N . m (2.0 0.2kgf . cm) H 0.4 0.02N . m (4.0 0.2kgf . cm)
CF-19KDRAXCM
K14
A K14-9
A K14-9
K14-2
A
K14-9
K14-3 K17 K14-4 K20 K32 K26 K14-8 K14-7 K14-10 K14-8 K14-7
A N6
K27
N6 K32 K28
A N6 A N10
K25
K16
K28
A N6
K14-10
K14-6
K16
A A N10
N10 K16
A N10
K55 K14-1
N10
A
A N10
A N10
K16
A N10
K14-1-2
K1
K14-1-1
K85
N6
N6
K84
CF-19KDRAXCM
K10-4
K10
K10-4-4 K10-4-1
K10-4-3
A N1 K10-4-3 A N1 K6 K10-4-5 K52-2 K52-1 K79 K79 K58 K7 K67 K65 K10-2 K10-3 K10 -1-5 A N1 A K10-1-13 E22 PEN Holder K10-1-9 K10-1-3 K10-1-5 K59 K66 K59 K52 K158 D N17 D N17 K29
K159
A K10-1-13 K42
E18 A N1
CF-19KDRAXCM
E36-11
K63
K64 E36-1-6
E36-2 E36-6
E36-5
E36-4 E36-1-8
E36-3
E36-7 E36-14 E36-7 E36-1-7 E36-1-1 E36-1-2 E36-14 E36-1-9 E36-15 E36-13 E36-12
E36-1
E36-1-4 E36-15
E36-1-12 E36-1-3
E36-8
CF-19KDRAXCM
A N4
K68 C N7
C N7
K69
C N7
C N7 C N7
A N4
C N7 A N15 C N7
C N7
K11-11
C N7 K68
C N7 C N7
CF-19KDRAXCM
DL31U1718AAA DL32U1718AAA DL33U1718AAA DL31U1719AAA DL32U1719AAA DL33U1719AAA DL34U1719AAA DL36U1719AAA DL37U1719AAA DL38U1719AAA DL39U1719AAA DL3UP1552AAA DL35U1719AAA DL3UP1566AAA N1ZYYY000034 N1ZYYY000035 N1ZYYY000036 N1ZYYY000037 DFJS1060ZA DFJS1193ZA DFJS1168ZA S N3CAYYY00048 N2AZZY000078 DFJS1120ZA S N5HAZ0000016 N5ZZ00000171 DFJS1059ZA S N5HZC0000042 DFJS1043ZA N2EABEC00006 BR-2330A/SF DFJS1195ZA K1NB94B00001 DFWV08A0121 DL3DW0190BAA DFGL0160YA DFHR3459ZC DFHR3958ZA DFHR3E27ZA DFHR3L72YA DFHR3L73YA DFHR3L74ZA DFHR6462ZA L5BDDYY00009 LNR0NP201 DFHR3N60ZA DFHR3925ZA L2DF00000031 DFHR3M60ZA DFHR3M61ZA DFHR3M59ZA DFHR3M04ZA DFHP7340ZA
E36-8 E36-9 E36-10 E36-11 E36-12 E36-13 E36-14 E36-15 E51 E401 E402 E403 E404 E405 E406 E407 E409 Accessories A1 A2 A3 A4 A6 A7 Packing Material P1 P2 P3 P4 Mechanical Parts K1 K3 K3-1 K3-2 K3-3 K3-4 K3-5 K3-6 K4 K5 K6 K7 K9 K10 K10-1 K10-1-3 K10-1-5 K10-1-9 K10-1-10 K10-1-12 K10-1-13 K10-2 K10-3 K10-4 K10-4-1 K10-4-1-1 K10-4-1-2 K10-4-3 K10-4-4 K10-4-5 K11 K11-1 K11-1-1
DFHR3L95ZA DFHR3M91ZA DFMY3271ZA DFHR3N57ZA DFHR3M01ZA DFHR3M02ZA DFHR3M03ZA DXHM0042ZA DL3UP1720AAA DFUP1587ZA DFUP1588ZA DFUP1644ZA DFUP1586ZA DFUP1645ZA DFUP1589ZA DFUP1591ZA DFUP1593ZA S S S S NCR-B/603E CF-AA1633AM4 K2CG3DR00003 DFQW5238ZA DFHS2059ZA DFQM8448MA DFPK1210WAP DFPE0733YA DFPK1216YA DFPE0859YA DFHM9017ZA-0 DFHR9150ZA-0 DFHR3578ZA DFHG2171ZA-0 DFHR3D96ZB-0 DFHR3E25ZB-0 DFHR3N17ZA-0 DFHP7324ZA DFQC9006ZB-0 DFQC9009ZC-0 DFKE9059YA DFBH3062ZA DFKE9086YA-0 DFWV80A0462 DFKM8195YA-0 DFHG1634YA-0 DFHM0319XA DFHR3469ZA DFHR3H08YA DFKM0563YA-0 DRHM5025YAT DFHE1122ZA DFHR3M77ZA DFWV84A0336 DL3DV0190AAA DFHR3L79ZA DFHR3M57ZA DFHR3476ZA DFHR3477ZA DFHP7315ZA DFWV80C0548 DFKM8196YA-0 DFHG1634YA-0
LCD PWB SPACER (DG) LCD BACK CUSHION (DG-1) LED THERMAL DIFFUSHION PLATE (DG) TAPE LCD SIDE CUSHION (RIGHT) LCD BACK CUSHIN (LCD LOWER) LCD SIDE CUSHION (LOWER) SCREW LED PCB UNIT AUDIO FPC 40PIN IO FPC 24PIN FPC(19MK2 SD LAN 24PIN) HSDPA FPC 50PIN FPC(19MK2 BT FPC 10PIN) PAD FPC 40PIN LED LEFT FPC 10PIN LED RIGHT FPC 6PIN LITHIUM ION BATTERY PACK AC ADAPTOR AC CORD MANUAL(CF-19MK3) TOUCH PANEL CLOTH RECOVERY DVD PACKING CASE HOLDER ACCESSORY BOX ACCESSORY BOX HOLDER EZC LID ASS'Y PALM REST ASS'Y M PALMREST TAPE OUTSIDE CLICK BUTTON RUBBER LED PANEL SHEET L LED PANEL SHEET R PALM REST SHEET CLICK RUBBER TAPE SHOULDER BELT ASS'Y STRAP BG ASS'Y LOCK PLATE ASS'Y HINGE HINGE TOP COVER ASM LCD FRONT CABINET/TS PANEL ASS'Y LCD FRONT CASE ASS'Y LCD CABINET CUSHION A LCD ELEPASS PEN FRICTION SHEET SPEAKER WP SHEET LCD FRONT CASE SCREW MAGNET MAGNET SPACER TS PANEL KIT TOUCHSCREEN PANEL ASS'Y PROTECTIVE FILM TS FPC PROTECTION SHEET DG SPACER A DG SPACER B TS TAPE LCD REAR CABINET ASS'Y LCD RAER CABINET UNIT LCD CABINET CUSHION A
NRP
1 1 1 1 2 5 2 4 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 3 1 1 1 1 1 2 2 1 1 1 2
NRP
NRP NRP
S S S
NRP NRP
NRP
K11-1-3 K11-1-6 K11-2 K11-3 K11-5 K11-9 K11-10 K11-11 K12 K12-1 K12-2 K12-3 K12-4 K12-5 K12-6 K12-7 K12-8 K12-9 K12-10 K12-11 K12-12 K12-13 K12-13-1 K12-13-2 K12-13-3 K12-13-4 K12-13-5 K12-13-6 K12-13-7 K12-13-8 K12-13-9 K12-13-10 K12-13-11 K12-14 K12-14-1 K12-14-2 K12-14-3 K12-14-4 K12-14-5 K12-14-6 K12-14-7 K12-14-8 K12-14-9 K12-14-10 K12-14-11 K12-15 K12-15-1 K12-15-2 K12-15-3 K12-15-4 K12-15-5 K12-15-6 K12-15-7 K12-15-8 K12-15-9 K12-15-10 K12-15-11 K12-16 K12-17 K12-18 K12-19 K12-20 K12-21
DFHM0319XA S DFKM0564YA-0 DFHR3L96ZA DFHR3L98ZA DFHR3L97ZA DFGB0165XA-0 DFGB0131YA-0 DFHR3N55ZA S DFKM8197XA-0 DFHM0320YA DFHR3434ZA DFHR3440ZA DFHR3470YA DFHR3D86ZA DFHR3D94YA DFHR3E15ZA DFHR3E16ZA DFHR3F00ZA DFHR3F01ZA DFHR6276ZA-0 S DFKM0553XA-0 S DFKE9089YC-0 DFBH3030ZA DFHM0315YC DFHR3466YA DFHR3509YA S DFKE0889ZA-0 S DFKE0891ZB-0 DFUN0068XA DFUS0323ZA DRHM0131ZAT DRQT26+D3KLT DXQT2+F3FNLT S DFKE9090XC-0 DFBH3030ZA DFHM0442ZA DFHR3466YA DFHR3508YA-0 S DFKE0889ZA-0 S DFKE0890ZB-0 DFUN0068XA DFUS0323ZA DRHM0131ZAT DRQT26+D3KLT DRHM5025YAT S DFKE9091YC-0 DFBH3030ZA DFHM0442ZA DFHR3466YA DFHR3588RA-0 S DFKE0889ZA-0 S DFKE0890ZB-0 DFUN0068XA DFUS0323ZA DRHM0131ZAT DRQT26+D3KLT DRHM5025YAT DRQT26+D3KLT DXQT3+F4FNLT DFHR3655YAT DFHR3F45ZAT DFHR3F65ZAT DFHR3F66ZBT
LCD ELEPASS LCD RAER CABINET LCD REAR CUSHION (1) LCD REAR CUSHION (3) LCD REAR CUSHION (2) TOUGH BADGE NEW PANASONIC BADGE DIMM EMI SHEET TOP CASE ASS'Y TOP ELEPASS AUDIO WATERPROOF SHEET DSUB WATERPROOF SHEET PSW WATERPROOF SHEET FS CASE WP SHEET GPS HOLE SHEET A LAN WP SHEET MODEM WP SHEET 1394 WP SHEET USB BACK WP SHEET POWER SW KNOB TOP CASE BAT LID ASS'Y LID HINGE LATCH PLATE BATTERY LID KNOB SHEET BAT COVER SHEET LID KNOB BAT LID LID KNOB SPRING LID KNOB SPRING PLATE SCREW SCREW SCREW HDD LID ASS'Y LID HINGE LID LATCH PLATE LID KNOB SHEET HDD COVER SHEET LID KNOB HDD LID LID KNOB SPRING LID KNOB SPRING PLATE SCREW SCREW SCREW PCMCIA LID ASS'Y LID HINGE LID LATCH PLATE LID KNOB SHEET PCMCIA LID SHEET LID KNOB HDD LID LID KNOB SPRING LID KNOB SPRING PLATE SCREW SCREW SCREW SCREW SCREW HDD CASE SPACER BATTERY CUSHION HDD TOP SHEET HDD SIDE SHEET
NRP NRP
NRP NRP
NRP NRP
NRP NRP
2 1 1 1 2 1 1 1 1 2 1 2 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 2 2 1 1 2 1 1 1 1 1 1 1 2 2 1 1 2 1 1 1 1 1 1 1 2 2 1 6 2 2 1 2 2
K12-22 K13 K13-1 K13-2 K13-3 K13-4 K13-5 K13-6 K13-7 K13-8 K14 K14-1 K14-1-1 K14-1-2 K14-2 K14-3 K14-4 K14-5 K14-6 K14-7 K14-8 K14-9 K14-10 K15 K16 K17 K18 K19 K20 K21 K22 K23 K24 K25 K26 K27 K28 K29 K30 K31 K32 K33 K34 K35 K37 K38 K39 K41 K42 K43 K45 K46 K47 K48 K49 K50 K51 K52 K52-1 K52-2 K53 K54 K55
DFHR3J11ZAT S DFKE9092YA-0 DFHG1669ZA DFHM0291ZA DFHM0294WA DFHM0295ZA S DFKE0892ZA-0 S DFKE0893YA-0 DFNW1604ZA DFUN0069XA S DFKM8192XB-0 DFHM9016ZA-0 DFHM0401ZA-0 DFHR3E14ZA DFHM0410YA DFHR3441ZA DFHR3F64ZA DFHR6283ZC-0 S DFKM0554WA-0 DFUS0316ZA DRHM5025YAT DXQT2+D25FNL DFMX0383TAT DFHE1019XA DFHG377ZA-1 DFHG1996ZB-0 DFHG1638ZC-0 DFHG1998ZB-0 DFHG1997ZB-0 DFHG1660ZC-0 DFHG1790ZA DFHG1902ZB-0 DFHG1903XB-0 DFHG1906ZB-0 DFHG1907WB-0 DFHM0286YB DFHM0452ZA DFHM0446ZA-0 DFHM0302XA-1 DFHM0303XA-0 DFHM0451ZA DFHM0449ZA DFHM0406ZA DFHM0407ZA DFHR3487YA DFHR3636ZA DFHR3D91ZA DFHR3E53ZA DFHR3F62ZA DFHR3G19ZA DFHR6246ZA DFHR6284ZA DFHR6286ZA-0 DFHR6289YB DFHR6290ZA-0 DFHR6312ZA DFHR7946ZA DFWV91J0032 DFHR9149ZA DFME0148YA DFMC0870WA DFMX0383TA DFMY0419ZA
PC DUMMY CARD CUSHION TABLET LATCH ASS'Y TABLET LATCH SHEET TABLET LATCH PLATE TABLET LATCH PIN TABLET LATCH SHAFT TABLET LATCH KNOB TABLET LATCH LEVER CUT WASHER LATCH KNOB SPRING BOTTOM CASE ASS'Y DIMM LID ASS'Y DIMM LID DIMM LID WP SHEET DU LID ANGLE DU LID WATERPROOF SHEET HDD BOTTOM SHEET DU LID BOTTOM CASE PLATE SPRING GUIDE PIN SCREW SCREW INSULATION SHEET DU CON SPONGE FOOT RUBBER SERIAL LID RUBBER MODEM LID RUBBER USB LID RUBBER RGB LID RUBBER LAN LID RUBBER BAT CUSHION DC-IN LID RUBBER 1394 LID RUBBER AUDIO LID RUBBER USB LID RUBBER 2 LID RUBBER PLATE A LID RUBBER PLATE C LCD HINGE COVER KEYBOARD PLATE(L) KEYBOARD PLATE(R) LID RUBBER PLATE B DU CNT ANGLE KBD CNT LID BAT CON ANGLE PORTRE SHEET CABLE HOLD SHEET KB CNT LID WP SHEET FS SCREW SHEET POWER SWITCH CABLE SHEET INSULATION SHEET HDD GUIDE DIMM HOLDER RF SW KNOB BAT CON HOLDER FS DUMMY CASE ANT CABLE HOLDER MP GUIDE SHEET DEGITIZER PEN ASS'Y DIGITIZER PEN PEN TETHER DU SPRING INSULATION PARTS DIMM THERMAL RUBBER
NRP NRP
NRP
NRP
NRP NRP
1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 6 7 2 1 4 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 3 2 1 1 1 1 1 1 1 1 1 1 1 2 1
K58 K59 K61 K62 K63 K64 K65 K66 K67 K68 K69 K70 K71 K79 K80 K80-1 K80-2 K80-3 K80-4 K80-5 K80-6 K80-7 K80-8 K80-9 K80-10 K80-11 K80-12 K81 K82 K83 K84 K85 K87 K88 K90 K93 K94 K95 K96 K98 K99 K100 K101 K102 K103 K104 K107 K108 K109 K110 K111 K113 K114 K115 K116 K117 K118 K120 K124 K126 K127 K129 K130
DFHM0325ZA DFHR3432ZA DFHR3M00ZA DFHR3L87ZA DFMX1394ZA DFHR3M80ZA DFHR3M56ZA DFHG2136ZA DFHR6411ZA-0 DFHR6413ZA-0 DFHR6412ZA-0 DFHR6298ZA DFMC0685ZA DFUQ0100ZA DFWV99A0132 DFHM0404ZB DFHM0416YA DFHR3589ZA DFHR3M76ZA DFHR3F54ZA DFHR6297ZA DL3UP1564CAA DFMX0383TA DFMX1265ZA DFMY3208ZA S L9DZYY000010 DXQT2+D4FNL DFQT0045ZA DFQT0066ZA DFQT0076ZA DFQT0055XA S DFGT1304YA DFHR3F85ZA DFMC0881ZA DFHM0309YA-1 DFMY3224ZA DFHM0412ZA DFHR3154ZA DFHR5399ZA DFHE0326XA DFHE0811YA DFHE1031ZA DFHG1962ZA DFHP7200ZA DFHP7256YA DFHP7257ZB DFHR3438ZA DFHR3483PA DFHR3J80ZB DFHR3642YA DFHR3643ZA DFHR3D90ZA DFHR3D93ZC DFHR3D97ZD DFHR3E02ZD DFHR3E19ZA DFHR3E34ZA DFHR3L39ZA DFHR6044XA DFMD2182ZA DFMD3125ZA DFMY0278YA DFMY0507ZA
CABLE HOLD PLATE ANT CABLE CUSHION LCD SIDE CUSHION (UPPER) LED FPC SHEET LED PWB INS SHEET LCD SIDE CUSHION (LEFT) PET TAPE LCD CABLE BUSH CABLE HOLDER ANTENNA COVER TABLET LATCH COVER HINGE CABLE HOLDER LCD CONDUCTIVE TAPE LOCK SPRING HDD MOUNTING KIT HDD CASE UPPER HDD CASE LOWER HDD CASE TAB HDD DAMPER HDD CON SHEET HDD CONNECTOR GUARD HDD FPC UNIT INSULATION PARTS INSULATION SHEET(HDD HEATER) WLAN SHEET HEATER(HDD) SCREW ENERGY STAR LABEL WINDOWS VISTA BASIC CENTRINO 2 DUO VPRO LABEL COA SERIAL LAMINATE NAMEPLATES MODEM CABLE SHEET BUSTERAID MODEM SIM LOCK PLATE WLAN SHEET RF-BT PLATE LCD CABLE TAPE CLAMPER GASKET-65TSV10-4-15 GASKET-65TSV4-3-50 GASKET-65TSV13-1.5-20 POWER SPRING SHEET AHDESIVE TAPE RF LED PWB TAPE LED PWB TAPE CLICK BUTTON SHEET OPERATION SHEET KB WP SHEET LCD CUSHION SHEET TP BOTTOM TAPE KB CNT HOLE CUSHION TP WP SHEET LED PWB TAPE PALM REST WP SHEET R LED SYAKOU SHEET RF SYAKOU SHEET OPERATION TAPE CLICK BUTTON PLATE PLATE HEAT PIPE BACK PLATE KENSINGTON 2 THERMAL RUBBER HEAT PIPE THERMAL RUBBER
NRP
NRP NRP
NRP NRP
NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP NRP
NRP NRP
1 2 2 1 1 2 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1
K131 K132 K133 K134 K137 K140 K141 K142 K144 K157 K158 K159 K161 K162 K163 K164 K165 K176 K177 K211 K212 K213 K214 K215 K216 K217 K218 K1051 K1603 K1604 N1 N2 N3 N4 N5 N6 N7 N8 N9 N10 N11 N14 N15 N16 N17 N18 N19
DFMY3208ZA DFMY5046ZA DFUQ0111ZA DFHR3859ZA DFMY3234ZA DFHR3488ZA DFHG429YA DFHR3G38ZA DFHP7270ZA DFMX1339ZA DFHR3J82ZA DFHR6352ZA DFHR3H64ZA DFHR6353ZA DFMC0901ZA DFMY0472ZA DFMY0475ZA DFHR3K72ZA-0 DFHR3K73ZA-0 DFHR3506YA DFMX1382ZA DFMX1403YA DFHE1130ZA DFHE1132ZA DFHR3L87YA DFMC8008ZA DFMX1388YA DFMY3264YA DFHR6339ZA-0 DFHR6340ZA-0 DFHE5025XA DFHE5058ZB DFHE5108ZA DRHM5054XA DRHM0115ZA DRHM5025YA DRQT26+E5FKL DRSB2+10FKL DRSB2+5FKL DRHM0061ZA DRYN3+J6FKL DRQT3+E4FKL DXYN26+J6FNL DXYN3+J10FNL DXYN3+J8FNL DXYN4+J8FNL XSB2+3FNL
WLAN SHEET HEAT PIPE UNIT POWER SW SPRING DC IN SHEET THERMAL DIFFUSION SHEET ANTENNA SHEET IO DC TUBE DIMM CUSHION ADHESIVE TAPE BAT INSULATION SHEET LCD CABLE PROTECTER CABLE GUIDE HINGE COIN BAT SHEET LAN CONN HOLDER GASKET-65TSV13-1(T9)-1.9 THERMAL RUBBER CPU ICH RUBBER PCMCIA COVER SHEET PCMCIA SMART CARD SHEET LCD SIDE CUSHION C CPU INSULATION SHEET WLAN INS SHEET GASKET-65TSV8-10.5-18 GASKET-65TSV10-2-30 PCB EDGE SHEET DIMM EMI PLATE ASS'Y LED PWB INS SHEET DIMM THERMAL SHEET DUMMY EXPRESS CARD DUMMY PC CARD SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW
NRP
NRP NRP
NRP NRP
1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 31 4 4 2 2 18 14 2 25 15 2 2 10 2 2 4 15
PART NO.
F1G1C104A042
DESCRIPTION
CAPACITOR, 16V, 0.1F
Q'TY
156
F1H1A225A025
21
EEFCX0D221R
12
F1J0J106A016
33
F1G0J105A001
CAPACITOR, 6.3V, 1F
40
C 63, 90, 92, 102, 107, 116, 120, 122, 135, 137, 162, 215, 223, 226, 227, 238, 317, 523 C 64, 75, 77, 149, 151, 152, 153, 154, 155, 157, 158, 160, 161, 163, 216, 219, 220, 221, 224, 228, 229, 232, 233, 234, 237, 240, 242, 244, 246, 300, 301, 303, 305, 306, 309, 312, 314, 315, 316, 320, 327, 341, 342, 344, 345, 354, 369, 370, 375, 386, 406, 413, 416, 468, 498, 528, 601, 615, 632, 633, 652, 700, 735, 741 C 65, 83, 86, 89, 94, 97, 100, 113, 115, 143, 144, 145, 170, 179, 180, 182, 191, 192, 195, 198, 285, 291, 383, 395, 396, 433, 434, 449, 454, 455, 457, 464, 491, 709, 710, 739 C 66, 99, 125, 206, 207, 208, 356, 357, 376, 465, 474, 495, 497, 499, 527, 616, 621, 623, 641, 653, 654, 659, 671, 717, 718, 726, 751, 753, 755, 757, 758 C 67 C 78, 84, 85, 87, 146, 147 C 112, 130, 134, 141, 270, 276 C 175, 178, 196, 201 C 204, 725 C 218, 225 C 231, 235 C 249, 492 C 250, 251, 252, 253, 254, 262, 263, 265, 429, 431, 458, 459, 460 C 282 C 308, 365, 374, 390, 391, 392, 393, 394, 397, 519, 539, 605, 696, 706, 738, 747, 763, 766 C 310, 361 C 313, 367 C 325, 326, 382 C 329 C 362, 682 C 368 C 385, 387, 640, 670, 716, 732, 759 C 418, 630, 655, 656, 719 C 428, 430 C 439, 441, 446, 450 C 469, 606, 625, 626, 672, , , , , , 702, 720, 737, 767, 769, 770, 771 C 477, 478, 479, 480, 600
F1J0J2260004
CAPACITOR, 6.3V, 22
18
F1G1E103A062
64
F1J0J106A013
36
F1G1H102A496
31
CAPACITOR, 50V, 10pF CAPACITOR, 6.3V, 0.47F CAPACITOR, 6.3V, 0.22F CAPACITOR, 6.3V, 1F CAPACITOR, 50V, 4700pF CAPACITOR, 6.3V, 100F CAPACITOR, 50V, 15pF CAPACITOR, 50V, 33pF CAPACITOR, 10V, 0.1F
1 6 6 4 2 2 2 2 13
F1G1C223A004 F1H1A1050015
1 18
F1G1H6R0A544 F1G1H5R0A543 F1J0J4750019 EEFCX0J121R F1J1E334A081 F1G1H271A495 F1G1H221A495 F1J0J475A009 F1G1H4R0A543 F1G1H471A496 F1H1H104A748
CAPACITOR, 50V, 6.0pF CAPACITOR, 50V, 5pF CAPACITOR, 6.3V, 4.7F CAPACITOR, 6.3V, 120F CAPACITOR, 25V, 0.33F CAPACITOR, 50V, 270pF CAPACITOR, 50V, 220pF CAPACITOR, 6.3V, 4.7F CAPACITOR, 50V, 4pF CAPACITOR, 50V, 470pF CAPACITOR, 50V, 0.1F
2 2 3 1 2 1 7 5 2 4 12
F1J1E105A009
CAPACITOR, 25V, 1F
C 494, 500 C 510, 624, 684, 701, 704, 707, 715, 727, 745 C 609, 610, 611, 612, 613, 614, 694 C 619, 620, 635, 636, 637, 638, 685, 686, 687, 688, 689, 690, 692, 695, 698, 729, 730, 761, 762, 772, 773, 774, 775, 779 C 622, 639, 642, 731 C 627 C 628, 631 C 634, 721, 723, 754 C 647, 648, 649, 740, 776 C 650 C 658, 748 C 678 C 679, 743 C 680 C 681 C 683, 744 C 691 C 693, 697 C 703 C 724 C 736 C 746 C 750 C 760 C 768 CF 1, 2, 3 CN 2 CN 4 CN 5 CN 6 CN 8 CN 9, 21 CN 10 CN 11 CN 14 CN 15 CN 16 CN 17 CN 18 CN 20 CN 22 CN 23 CN 24 CN 25 CN 27 CN 33 D 1, 3, 4, 14 D5 D7 D 11, 12, 13 , D 600, 624 D 601, 602, 603 D 604
CAPACITOR, 10V, 0.068F CAPACITOR, 50V, 100pF CAPACITOR, 50V, 0.01F CAPACITOR, 25V, 10F
2 9 7 24
F1G1H220A542 EEFCX0G151R EEFCX0J101R F1H1C224A074 F1G1C473A004 EEFCD0J470ER F1H1H1830001 F1G1H151A495 F1G1H470A542 F1G1H561A496 F1H1H222A748 F1G1H331A496 F2H0D101A003 F1H1H182A748 F1H0J475A010 F1G1H182A496 EEFCD0D101ER EEFSX0D471XE F1G1H222A496 F1G1H391A496 F1G1H152A496 D4CC11030026 K1MYL0B00003 K1NAF0D00003 K1KY42B00001 K1FY104BA024 K1KA14AA0252 K1MY24BA0310 K1MYL0B00004 K1MY52BA0190 K1KA02B00292 K1MY30AA0158 K1MN50AA0018 K1KA20A00310 K1MN26AA0074 K1MY04AA0041 K2HZ104B0014 K1MY40A00001 K1KY12A00005 K1KYA0A00019 K1MN40B00048 K1KA02BA0014 MA2J72900L B0JDBE000002 B0KB00000044 MA3J14700L B0JCRD000015 B0ADDH000004 MAZ81200ML
CAPACITOR, 50V, 22pF CAPACITOR, 2V, 150F CAPACITOR, 6.3V, 100F CAPACITOR, 16V, 0.22F CAPACITOR, 16V, 0.047F CAPACITOR, 6.3V, 47F CAPACITOR, 50V, 0.018F CAPACITOR, 50V, 150pF CAPACITOR, 50V, 47pF CAPACITOR, 50V, 560pF CAPACITOR, 50V, 2200pF CAPACITOR, 50V, 330pF CAPACITOR, 2V, 100F CAPACITOR, 50V, 1800pF CAPACITOR, 6.3V, 4.7F CAPACITOR, 50V, 1800pF CAPACITOR, 2V, 100F CAPACITOR, 2V, 470F CAPACITOR, 50V, 2200pF CAPACITOR, 50V, 390pF CAPACITOR, 50V, 1500pF THERMISTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR, USB CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR FPC CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR DIODE DIODE DIODE DIODE DIODE DIODE DIODE
4 1 2 4 5 1 2 1 2 1 1 2 1 2 1 1 1 1 1 1 1 3 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 3 2 3 1
D D D D D D D D D D F F F F F IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC
605 606, 622 608 609, 631, 632, 638, 640 610, 630 612, 613, 615, 617, 618, 623 616 619, 621 620 637 1 2, 3, 5, 8, 11 4 10 600 1 2 3 4 5 6 7 8 9 12, 19 14 15, 60 16 18, 32, 34, 35 20 21, 22 23, 24, 25, 37 26 28 30 31 33 39 40 42 44 46, 55, 56, 57, 63, 64 47 51, 52 53 54 58, 620 600 601 602 605 606 607 608 610, 612 613
MAZ81800ML MA3S132E0L B0JCQD000001 B0JCMD000046 B0JDAE000004 MAZ80510ML MAZ80620ML MA2S11100L B2ABAM000002 B0JCCE000008 K5H502Z00003 K5H202Z00005 K5H402Z00003 K5Y802A00003 K5H103A00004 C2GBD0000051 C1CB00003067 C1CB00003007 C1CB00003068 C1CB00002585 C1CB00003002 C1CB00003035 C1DB00001159 C0DBFYY00049 C0DBZYY00026 C0DBZYY00265 C3EBDY000005 C0DBZYY00016 C0JBAZ002422 C0ZBZ0000978 C0JBAS000218 C0EBE0000460 C0EBH0000457 C2CBYY000639 C3FBNY000187 C1CB00002790 C0JBAA000511 C0JBAA000381 C0JBAZ002192 C1CB00003064 C0EBY0000419 C0JBAA000362 C0CBCBC00137 C0JBAA000345 C0JBAC000363 C0JBAC000367 C0JBAE000321 C0ABZA000047 C0ABBA000093 C0DBAYY00194 C0DBEFH00002 C0DBAYY00282 C0EBE0000333 C0DBDJH00009 C0DBALH00003 C0DBAYY00423
DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE FUSE, 5A, 32V FUSE, 2A, 32V FUSE, 4A, 32V FUSE, 8A, 125V FUSE, 10A, 125V CPU CORE CHIP(GMCH) LSI CORE CHIP(ICH) IC THERMAL SENSOR LSI IC, PERIPHERAL LSI REGULATOR IC, USB POWER SW POWER MANAGEMENT SWTICH IC, EEPROM IC IC, FET SWITCH IC IC, LOGIC IC IC IC FLASH ROM IC, SECURITY CHIP IC IC, LOGIC IC IC, CARD BUS CONTROLLER IC, VOLTAGE DETECTOR IC, LOGIC IC, REGULATOR IC, LOGIC GATE LOGIC IC, LOGIC IC, LOGIC IC, AMP IC, OP AMP IC, DC/DC IC, REGULATOR DC/DC CONTROLLER FOR GMCH IC IC, LINER IC IC
1 2 1 5 2 6 1 2 1 1 1 5 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 4 1 2 4 1 1 1 1 1 1 1 1 1 6 1 2 1 1 2 1 1 1 1 1 1 1 2 1
S S S S S
IC IC IC L L L L L L L L L L L L L L L L L L L L PA Q
Q Q Q Q
Q Q Q Q Q Q Q Q
Q Q Q Q R
R R R
616, 619 617 618 1, 33 2, 3, 4, 7, 8, 9, 11 6, 10 15, 37, 46, 47, 48, 49, 50, 51, 65, 66, 71, 72, 16, 17, 18, 22, 31 19, 20, 21, 23 24, 27, 32 30 34 35 36, 38, 45, 75 40, 41, 42 52 60 600 601 602 606, 611, 612 609 610 2 1, 4, 48, 49, 53, 54, 55, 646, 657, 659, 661, 668, 689, 689 691 2, 10, 37, 50, 302, 620, 666 6, 7, 30, 31, 46, 47, 610, 621, 674, 679, 680 8, 11, 14, 19, 28, 35, 45, 630, 667, 671 12, 34, 38, 625, 629, 672, 673, 675, 676, 677, 678 15, 20, 27, 29, 43, 301, 608, 619, 649, 655, 656, 664, 665, 670, 690 17 21, 22, 23, 24, 25, 26 36 42 44, 603, 604, 606, 607 600, 601, 602 611 613, 618, 633, 636, 647, 648, 652, 653, 660, 692, 693 614, 662 622, 627 634, 635, 669, 686 658 1, 14, 25, 26, 48, 49, 52, 155, 167, 221, 260, 286, 329, 366, 377, 398, 411, 412 2, 3, 35, 111, 113 4, 5 6, 7, 253, 461
C0JBAB000621 C0JBAD000194 C0DBFYY00031 G1C1R0MA0289 J0JHC0000078 G1C100M00038 J0MAB0000200 J0JYC0000098 G1C470MA0330 J0JJC0000022 G1C100MA0077 G1C1R0MA0380 J0JKC0000007 J0JHC0000074 J0JDC0000045 J0JDC0000105 J0JJC0000015 G1C100M00030 G1C4R7MA0240 G1CR60MA0299 G1C2R7Z00003 G1CR82M00006 G1A160HA0032 D4FB1R100015 B1CFGD000023
IC, LOGIC 1GATE LOGIC IC IC DC POWER LINE INDUCTOR DC POWER LINE BEADS INDUCTOR INDUCTOR DC POWER LINE BEADS DC POWER LINE INDUCTOR DC POWER LINE BEADS COIL DC POWER LINE INDUCTOR INDUCTOR INDUCTOR INDUCTOR CHIP BEADS INDUCTOR COIL CHOK COIL COIL COIL COIL COIL OVER CURRENT PROTECTOR TRANSISTOR
2 1 1 2 7 2 14 5 4 3 1 1 1 4 3 1 1 1 1 1 3 1 1 1 14
7 11 10 11
B1GBCFJN0037
TRANSISTOR
15
1 6 1 1 5 3 1 11
2 2 4 1 18
5 2 4
R 8, 33 R 9, 34, 67, 69, 71, 694, 765, 773 R 13, 27, 28, 29, 30, 39, 93, 95, 99, 100, 102, 105, 112, 117, 130, 131, 145, 182, 185, 187, 192, 223, 226, 266, 320, 343, 359, 385, 386, 388, 392, 393, 449, 462, 505, 622, 623, 676, 684, 685, 687, 690, 693, 704, 714, 719, 723, 733, 751, 757, 781, 814 R 16, 18 R 17 R 20, 334, 478, 626, 627, 630, 635, 741, 742, 743, 747 R 21, 601, 608, 615, 793 R 22, 364, 436, 475, 476 R 23 R 36 R 37, 180, 241, 256 R 40, 41 R 44 R 45 R 46, 47, 138, 146, 147, 150, 154, 160, 165, 213, 243, 262, 263, 276, 288, 296, 300, 304, 308, 324, 325, 326, 328, 344, 345, 353, 354, 365, 368, 372, 381, 384, 403, 404, 405, 414, 415, 437, 438, 439, 440, 441, 442, 443, 445, 454, 470, 471, 480, 482, 484, 487, 489, 491, 504, 604, 628, 651, 701, 746, 755, 761, 792, 809, 812, 815, 830 R 61, 62, 153, 183, 367, 380, 500, 502 R 63 R 68, 89 R 70, 800, 801 R 80, 212, 290, 301, 306, 339, 397, 424, 425, 469, 477, 610, 611, 654, 655, 656, 657, 658, 659, 683, 700, 769 R 82, 84, 406, 407 R 85, 86, 87 R 97, 104, 110, 114, 116, 347, 492, 682, 698, 726, 727, 731, 763, 784 R 103, 118 R 106 R 109 R 120, 121, 122, 125, 126, 127 R 123, 128, 331
2 8 52
2 1 11
RESISTOR, 1/16W, 5.6K RESISTOR, 1/16W, 56 RESISTOR, 1/16W, 68 RESISTOR, 1/16W, 221 RESISTOR, 1/16W, 24.9 RESISTOR, 1/16W, 80.6 RESISTOR, 1/16W, 2370 RESISTOR, 1/16W, 49.9 RESISTOR, 1/16W, 10K
5 5 1 1 4 2 1 1 67
RESISTOR, 1/16W, 33 RESISTOR, 1/16W, 1.02K RESISTOR, 1/16W, 499 RESISTOR, 1/16W, 3K RESISTOR, 1/16W, 100
8 1 2 3 22
4 3 14
RESISTOR, 1/16W, 1 RESISTOR, 1/16W, 4.7 RESISTOR, 1/16W, 2.2 RESISTOR ARRAY RESISTOR ARRAY
2 1 1 6 3
R R R R R R
R R
R R R R R R
R R R R R R R R
R R R R R R R R R R R R R R R R R R R R
124, 287, 374, 444, 689 129 139 140, 143, 246, 254 141, 148, 152, 203, 423, 479 151, 239, 370, 371, 607, 665, 672, 673, 740, 822, 824, 825, 826 158, 200 159, 168, 176, 189, 190, 208, 214, 230, 269, 272, 273, 279, 281, 284, 285, 307, 309, 310, 311, 327, 332, 333, 360, 399, 400, 401, 402, 456, 460, 507, 508, 600, 602, 603, 612, 666, 667, 668, 729, 813, 823, 827 162, 207 164, 202, 205 170 179 201 210, 211, 218, 232, 233, 234, 303, 413, 416, 417, 418, 419, 420, 421, 434, 435 220, 227 229, 270, 640, 749, 796 237 238, 240, 245, 716, 717 250, 255 259, 261 271 289, 291, 292, 293, 294, 295, 297, 298, 299, 305, 762 302, 474 335, 458 337, 390 375 379 394, 395, 396, 663, 764, 766, 774, 789, 811 428, 429, 430, 431, 432 433 446, 447, 448, 452, 453, 795 605 606, 609 613, 618, 725, 777 614, 619, 699, 718, 724 616 620, 621 624 625 629, 748 631, 639, 662 636, 732, 739, 745, 767, 785
RESISTOR, 1/16W, 470 RESISTOR, 1/10W, 100 RESISTOR, 1/16W, 475 RESISTOR ARRAY RESISTOR ARRAY RESISTOR, 1/16W, 1M
5 1 1 4 6 13
ERJ2RKF3241X ERJ2GEJ104X
2 42
RESISTOR, 1/16W, 453 RESISTOR, 1/16W, 15 RESISTOR, 1/16W, 510 RESISTOR, 1/16W, 22.6 RESISTOR ARRAY RESISTOR ARRAY
2 3 1 1 1 16
RESISTOR, 1/16W, 120 RESISTOR, 1/16W, 470K RESISTOR, 1/16W, 10M RESISTOR, 1/16W, 56 RESISTOR, 1/16W, 20K RESISTOR, 1/16W, 332K RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 220
2 5 1 5 2 2 1 11
D1H81014A024 ERJ2RKF1002X ERJ2GEJ512X ERJ2GEJ681X ERJ2RKF4991X ERJ2GEJ223X ERJ2RKF3901X ERJ2RKF5602X ERJ2GEJ472X ERJ3GEYJ3R3V D1BDR1000002 ERJ2RKF1503X ERJ2RKF1003X D1ZZ00000046 ERJ2RHD103X ERJ3GEYJ562V D1BDR068A100 ERJ2GEJ153X ERJ2GEJ473X ERJ3GEYJ100V
RESISTOR ARRAY RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 5.1K RESISTOR, 1/16W, 680 RESISTOR, 1/16W, 4.99K RESISTOR, 1/16W, 22K RESISTOR, 1/16W, 3.9K RESISTOR, 1/16W, 56K RESISTOR, 1/16W, 4.7K RESISTOR, 1/16W, 3.3 RESISTOR, 1/8W, 0.1 RESISTOR, 1/16W, 150K RESISTOR, 1/16W, 100K RESISTOR, 1W, 5m RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 5.6K RESISTOR, 1/3W, 0.068 RESISTOR, 1/16W, 15K RESISTOR, 1/16W, 47K RESISTOR, 1/16W, 10
2 2 2 1 1 9 5 1 6 1 2 4 5 1 2 1 1 2 3 6
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R SW X X X X X ZA ZA C C
637 638 641 642, 810 643, 794, 797 644 645 646 647, 649, 728, 734, 753, 816 648, 754, 808 650, 652, 756 653 660, 661 664 669 670, 671 680 681, 691, 692 686 695, 776 702 705 706, 790 707 708 709, 778 710 711 715, 791 720 721 722 744, 750 752 758 760 768 772 780 783 787, 806 788 798, 803, 807 802 804 805 2 1 2 3 4 5 1, 2, 5, 6, 7, 10, 11 8, 9 709, 712 710, 711
ERJ2RKF1102X ERJ2RKF1302X ERA3YEB622V ERA3YEB203V ERA3YKB104V ERJ3RBD103V ERJ3RBD132V ERJ3RBD303V D1BDR022A099 D1BDR033A099 D1BDR018A099 ERJ2GEJ333X ERJ6GEYJ222V ERJ2GEJ684X ERJ2GEJ225X ERJ6GEYJ122V ERJ2RKF6801X ERJ3GEYJ1R0V ERJ2RKF1800X D1ZZ00000093 ERJ2RKF4702X ERJ2RKF5103X ERJ2RKF5101X ERJ2RHD222X ERJ2RKF3001X ERJ3GEYJ101V ERJ2GEJ393X ERJ2RKF7501X ERJ3GEYJ2R2V ERJ2RKF8202X ERJ3GEYJ102V ERJ2RKF2202X ERJ2RKF1502X ERJ2RKF4701X D1BDR016A099 ERJ2RKF1202X ERJ2RKF6201X ERJ2RHD393X ERJ2RKF6981X ERJ3GEYJ104V ERJ2RKD114X ERJ2RKF1501X ERA3YEB333V ERJ2RHD3652X ERA3YEB243V ERJ2GEJ154X K0D112B00071 H0J143500079 H0J327200085 H0J245500096 H0J2505A0053 H2D200500011 K1YGZZ000060 K1YGZZ000068 F1G0J105A001 F1K1E1060001
RESISTOR, 1/16W, 11K RESISTOR, 1/16W, 13K RESISTOR, 1/16W, 6.2K RESISTOR, 1/16W, 20K RESISTOR, 1/16W, 100K RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 1.3K RESISTOR, 1/16W, 30K RESISTOR, 1/3W, 0.022 RESISTOR, 1/3W, 0.033 RESISTOR, 1/3W, 0.018 RESISTOR, 1/16W, 33K RESISTOR, 1/10W, 2.2K RESISTOR, 1/16W, 680K RESISTOR, 1/16W, 2.2M RESISTOR, 1/10W, 1.2K RESISTOR, 1/16W, 6.80K RESISTOR, 1/16W, 1 RESISTOR, 1/16W, 180 RESISTOR, 1W, 1m RESISTOR, 1/16W, 47K RESISTOR, 1/16W, 510K RESISTOR, 1/16W, 5.1K RESISTOR, 1/16W, 2.2K RESISTOR, 1/16W, 3K RESISTOR, 1/16W, 100 RESISTOR, 1/16W, 39K RESISTOR, 1/16W, 7.5K RESISTOR, 1/16W, 2.2 RESISTOR, 1/16W, 82K RESISTOR, 1/10W, K RESISTOR, 1/16W, 22K RESISTOR, 1/16W, 15K RESISTOR, 1/16W, 4.7K RESISTOR, 1/13W, 0.016 RESISTOR, 1/16W, 12K RESISTOR, 1/16W, 6.2K RESISTOR, 1/16W, 39K RESISTOR, 1/16W, 6.98K RESISTOR, 1/16W, 100K RESISTOR, 1/16W, 110K RESISTOR, 1/16W, 1.5K RESISTOR, 1/16W, 33K RESISTOR, 1/16W, 36.5K RESISTOR, 1/16W, 24K RESISTOR, 1/16W, 150K SW CRYSTAL OSCILLATOR CRYSTAL OSCILLATOR CRYSTAL OSCILLATOR CRYSTAL OSCILLATOR CERAMIC LOCK SPACER STUD CAPACITOR, 6.3V, 1F CAPACITOR, 25V, 10F
1 1 1 2 3 1 1 1 6 3 3 1 2 1 1 2 1 3 1 2 1 1 2 1 1 2 1 1 2 1 1 1 2 1 1 1 1 1 1 1 2 1 3 1 1 1 1 1 1 1 1 1 7 2 2 2
AUDIO PCB
C 900, 906, 916, 917, 934, 935, 966 C 901, 903, 943, 948 C 902, 907, 908, 912, 915, 918, 919, 932 C 909 C 910, 928, 929, 930, 931 C 911, 922, 937, 938, 947, 951, 956 C 913 C 914, 920, 921, 952, 958 C 924, 957 C 925, 939, 940, 964, 965 C 926, 927 C 933, 941, 946 C 936 C 949, 950, 953, 954 C 960, 961, 962, 963 CN 901 CN 902 CN 904 D 902 F 902 IC 900 IC 901 IC 902 IC 903 IC 905 IC 960 IC 961 JK 901, 902 JK 903, 960, 961, 962, 963 L 900, 901, 904, 905, 907, 960, 961 L 902, 903 L 906 Q 900, 905 Q 902 Q 903, 904 R 901, 922 R 902, 906, 911 R 905, 910, 937, 944 R 912 R 913, 920, 921, 928, 932, 947, 951, 954 R 915, 916 R 918, 919 R 923 R 926 R 927 R 929 R 930, 952 R 931, 933 R 934, 938, 946, 948 R 935 R 936 R 940, 942 R 941, 945 F1G1A104A014 F1H1A225A025 F1G0J224A001 F1G1E103A062 F1H1A1050015 F1J0J106A013 F1G1H221A495 F1G1C104A042 F1H0J1050022 F1G1H102A496 F1H1A474A028 F1G1H1010005 F1G0J105A001 F1L0J107A016 F1G1H270A542 K1MN40B00048 K1MY12BA0309 K1KA02BA0014 B0JDBE000002 K5H202Z00005 C1CB00002983 C0CBCBC00130 C0JBAE000306 C0JBAS000251 AN12945A-VB C1CB00003028 C0JBAB000621 K2HC103B0197 K1QZA1AE0001 J0JCC0000286 J0MAB0000230 J0JJC0000015 B1GBCFNN0042 UP04213G0L B1CFGD000023 ERJ2RKF2671X ERJ2GEJ330X ERJ2GE0R00X ERJ2GEJ473X ERJ2GEJ103X ERJ2RKF1003X ERJ2GEJ333X ERJ2GEJ100X ERJ2RHD3922X ERJ2RHD203X ERJ2RKF1602X ERJ2GEJ104X ERJ2RKF1002X ERJ2GEJ102X ERJ2GEJ471X ERJ2GEJ472X ERJ2GEJ4R7X ERJ2GEJ392X CAPACITOR, 10V, 0.1F CAPACITOR, 10V, 2.2F CAPACITOR, 6.3V, 0.22F CAPACITOR, 25V, 0.01F CAPACITOR, 10V, 1F CAPACITOR, 6.3V, 10F CAPACITOR, 50V, 220pF CAPACITOR, 16V, 0.1F CAPACITOR, 6.3V, 1F CAPACITOR, 50V, 1000pF CAPACITOR, 10V, 0.47F CAPACITOR, 50V, 100pF CAPACITOR, 6.3V, 1F CAPACITOR, 6.3V, 100F CAPACITOR, 50V, 27pF CONNECTOR CONNECTOR CONNECTOR DIODE FUSE, 2A, 32V LSI IC, REGURATOR IC, IC IC, AUDIO AMP IC, DPDT SWITCH IC, LOGIC JACK CONNECTOR INDUCTOR COMMON MODE FILTER INDUCTOR TRANSISTOR TRANSISTOR TRANSISTOR RESISTOR, 1/16W, 2.67K RESISTOR, 1/16W, 33 RESISTOR, 1/16W, 0 RESISTOR, 1/16W, 47K RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 100K RESISTOR, 1/16W, 33K RESISTOR, 1/16W, 10 RESISTOR, 1/16W, 39.2K RESISTOR, 1/16W, 20K RESISTOR, 1/16W, 16K RESISTOR, 1/16W, 100K RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 1K RESISTOR, 1/16W, 470 RESISTOR, 1/16W, 4.7K RESISTOR, 1/16W, 4.7 RESISTOR, 1/16W, 3.9W 7 4 8 1 5 7 1 5 2 5 2 3 1 4 4 1 1 1 1 1 1 1 1 1 1 1 1 2 5 7 2 1 2 1 2 2 3 4 1 8 2 2 1 1 1 1 2 2 4 1 1 2 2
R 950
ERJ3GEY0R00V F1H1H104A748 F1L1E106A017 F1G1H330A542 F1G1C104A042 EZASCE101M K1MY24AA0179 K1FA209BA004 K1FB115BA014 DFJS1063ZA B0JCRD000015 MA2J72900L K5Y802A00003 K2EEYB000001 J0JKC0000007 J0JDC0000038 D4FB1R100015 D1BDR4700001 ERJ2RKF75R0X ERJ2GEJ222X F1G1H681A496 F1G1E103A062 F1G1C104A042 F1J0J106A016 D4CC11030026 K1MY04BA0334 K1MY06BA0309 K1MY40A00001 K1MY08AA0158 K1KA02BA0014 K1MY10AA0158 K1MY10BA0309 K5H202Z00005 C0EBE0000460 C1DB00001417 B4ZZ00000019 B1GKCFJN0004 ERJ2GEJ273X ERJ2GEJ822X ERJ2GEJ105X ERJ2GEJ222X ERJ2GEJ471X D1H81034A024 EVQPLDA15 H2D400400012 K1MY10AA0158 B3ABB0000210 ERJ2GEJ471X EVQPLDA15
RESISTOR, 1/16W, 0 CAPACITOR, 50V, 0.1F CAPACITOR, 25V, 10F CAPACITOR, 50V, 33pF CAPACITOR, 16V, 0.1F CAPACITOR ARRAY FPC CONNECTOR CONNECTOR CONNECTOR I/O DC CABLE DIODE DIODE FUSE, 8A, 125V JACK INDUCTOR CHIP BEADS OVER CURRENT PROTECTOR RESISTOR, 1/8W, 0.47 RESISTOR, 1/16W, 75 RESISTOR, 1/16W, 2.2K CAPACITOR, 50V, 680pF CAPACITOR, 25V, 0.01F CAPACITOR, 16V, 0.1F CAPACITOR, 6.3V, 10F CAPACITOR 6 3V 10 F THERMISTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR FUSE, 2A, 32V IC IC, FLAT PAD CONTROLLER SENSOR TRANSISTOR RESISTOR, 1/16W, 27K RESISTOR, 1/16W, 8.2K RESISTOR, 1/16W, 1M RESISTOR, 1/16W, 2.2K RESISTOR, 1/16W, 470 RESISTOR ARRAY SWITCH OSCILLATOR, 4MHz CONNECTOR DIODE RESISTOR, 1/16W, 470 SWITCH
1 1 1 7 1 2 1 1 1 1 1 1 1 1 1 7 1 1 3 2 2 1 5 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 2 1 2 2 1 2 1 1 1 1 6
IO PCB
C 880 C 883 C 884, 885, 886, 887, 888, 889, 890 C 891 C 892, 893 CN 880 CN 881 CN 882 CN 883 D 880 D 881 F 800 JK 880 L 880 L 881, 882, 883, 884, 885, 886, 887 PA 880 R 881 R 882, 883, 884 R 885, 886
S S
PAD PCB
C C C C CF CN CN CN CN CN CN CN F IC IC IC Q R R R R R RA SW X CN LD R SW 800, 801 802 803, 804, 806, 807, 808 805 800 800 801 802 803 804 805 806 800 800 801 802, 803 800, 801 800 801, 802 803 804, 805 808, 810 800 802, 803 800 950 951 953 950, 951, 952, 953, 954, 955
SW PCB
B3ABB0000210
DIODE
PR PCB
C 851, 852, 854 C 855, 856, 857 CA 851, 852, 854, 857, 858, 859 CN 850 CN 851 L 850 L 852, 853 F1J1A1050021 J0MAB0000146 J0HABC000004 K1KYA0A00018 K1KAA0AA0244 J0MAB0000200 J0JJC0000015 F1J0J106A016 F1G1C104A042 F1G1H102A496 F1G1E103A062 F1G1H270A542 F1G1HR50A543 K1MY10BA0309 C0JBAZ002422 N5HZZ0000056 C0EBE0000460 C0JBAC000382 K1QZA1AE0001 J0JJC0000015 G1C5N6ZA0029 J0MAB0000200 B1GBCFNN0042 B1DHDC000028 ERJ2GEJ103X K1MY06AA0158 B3AGB0000040 B3ADB0000065 B3ABB0000210 F1G1H330A542 F1G1C104A042 F1H2A103A020 F1L3D102A003 K1MY24BA0310 K1NA09E00076 K1KA08BA0014 B3ACB0000207 D1H87504A024 ERJ2GEJ103X G5BYC0000015 F1G1H1010005 F1J0J106A016 EEFUD0J151ER F1G1C104A042 EEFCX0J121R F1G1H221A495 K1MN50BA0153 K1MY52BA0190 CAPACITOR, 10V, 1F INDUCTOR CAPACITOR ARRAY CONNECTOR CONNECTOR INDUCTOR INDUCTOR CAPACITOR, 6.3V, 10F CAPACITOR, 16V, 0.1F CAPACITOR, 50V, 1000pF CAPACITOR, 25V, 0.01F CAPACITOR, 50V, 27pF CAPACITOR, 50V, 0.5pF CONNECTOR IC, FET SWITCH BLUETOOTH MODULE IC IC, LOGIC CONNECTOR INDUCTOR INCUCTOR INDUCTOR TRANSISTOR TRANSISTOR RESISTOR, 1/16W, 10K CONNECTOR DIODE DIODE DIODE CAPACITOR, 50V, 33pF CAPACITOR, 16V, 0.1F CAPACITOR, 100V, 0.01F CAPACITOR, 2000V, 1000pF CONNECTOR CONNECTOR CONNECTOR LED RESISTOR ARRAY RESISTOR, 1/16W, 10K TRANCE CAPACITOR, 50V, 100pF CAPACITOR, 6.3V, 10F CAPACITOR, 6.3V, 150F CAPACITOR, 16V, 0.1F CAPACITOR, 6.3V, 120F CAPACITOR, 50V, 220pF CONNECTOR CONNECTOR 3 3 6 1 1 1 2 1 4 2 2 1 1 1 1 1 1 1 1 2 1 1 1 1 3 1 1 1 1 1 6 4 1 1 1 1 1 1 1 2 2 4 2 8 1 1 1 1
BT PCB
C C C C C C CN IC IC IC IC JK L L L Q Q R CN LD LD LD 1 2, 4, 7, 11 3, 5 6, 9 8 10 2 1 2 3 5 1 1, 2 4 5 1 2 1, 2, 3 780 781 782 783
SD-LAN PCB
C 880 C 881, 882, 884, 885, 886, 887 C 889, 890, 891, 892 C 893 CN 880 CN 881 CN 882 LD 880 R 880 R 882 T 880, 881
HSDPA PCB
C C C C C C CN CN 600, 603 601, 602, 604, 608 609, 610 611, 612, 613, 614, 615, 616, 617, 620 619 622 600 601
CN CN CN D D IC IC IC IC IC IC JK L L L Q Q Q R R R R R R R R R R R SW ZA
602 603 604 600 603 600 601 602 603 604 605 600, 601 600, 601 602 603 600 602, 604 603 600 601 602, 606, 609, 615, 616, 624 603, 613 604, 611, 612, 619 608 610 617 618 621, 622 623 600 600, 601
K1NA08E00013 K1FY104BA024 K1MY10BA0309 B0KB00000044 B0JCRC000002 C0JBAZ002422 C0JBAC000382 C0DBAYY00204 C0DBZGD00016 C0DBZYY00026 C0EBE0000460 K1QZA1AE0001 J0JJC0000015 J0MAB0000200 G1C2R7MA0273 B1DHFD000015 B1GBCFNN0042 B1CFGD000023 D1BDR0330001 D1BDR0470002 ERJ2GEJ103X ERJ2GE0R00X ERJ2GEJ101X ERJ2RKF1001X ERJ6GEY0R00V ERJ2RKF1002X ERA3YEB303V ERJ2GEJ104X ERJ2GEJ471X K0D444A00041 K1YGZZ000060 K1KA02AA0051 K0D112A00096 F1K1H2250001 K1MY08BA0309 K1KA10BA0014 B0JCPG000005 MAZ82200ML C0DBAYY00472 G1C4R7MA0077 B1DFFG000004 B1CFGD000023 D1BDR047A100 ERJ2RHD473X ERJ2RHD221X ERJ2RHD103X ERJ2GE0R00X ERJ2GEJ101X ERJ2RKD274X K0D112B00071 K1QZB2AA0002 K1QZA1AE0001
SIM CONNECTOR CONNECTOR, USB CONNECTOR DIODE DIODE IC, FET SWITCH IC, LOGIC IC, DC/DC CONVERTER IC IC, USB POWER SW IC CONNECTOR INDUCTOR INDUCTOR INDUCTOR, COIL TRANSISTOR TRANSISTOR TRANSISTOR RESISTOR, 1/8W, 0.033 RESISTOR, 1/8W, 0.047 RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 0 RESISTOR, 1/16W, 100 RESISTOR, 1/16W, 1K RESISTOR, 1/10W, 0 RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 30K RESISTOR, 1/16W, 100K RESISTOR, 1/16W, 470 SWTICH SPACER CONNECTOR SW CAPACITOR, 50V, 2.2F FPC CONNECTOR CONNECTOR SCHOTTKY DIODE DIODE IC INDUCTOR FET TRANSISTOR RESISTOR, 1/3W, 0.047 RESISTOR, 1/16, 0.047K RESISTOR RESISTOR, 1/16W, 10K RESISTOR, 1/16W, 0 RESISTOR, 1/16W, 100 RESISTOR, 1/16W, 270K SW COAXIAL CONNECTOR CONNECTOR
1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 2 1 1 1 6 2 4 1 1 1 1 2 1 1 2 1 1 1 1 1 1 6 1 1 1 1 1 2 1 1 1 6 1 1 1 4
POWER PCB
CN 980 SW 980
LED PCB
C CN CN D D IC L Q Q R R R R R R R SW 713 601 602 638 639, 640, 641, 642, 643, 644 615 612 663 800 740 809, 822 812 813 815 816, 817, 818, 819, 820, 821 824 700