Académique Documents
Professionnel Documents
Culture Documents
TUBING
Unless otherwise agreed, MARUICHI API tubular goods are marked as follows:
Identification
Marking
(2)
(3) (4) (5) (6) (7) (8)
ISO11960 5CT 0069
UF 4.70 J E
Die stamp (option)
(1)
(2)
(3) (4) (5) (9)
(6) (7) (8) (10) (11) (12) (13) (14) (15)
ISO11960 5CT 0069
UF 2 3/8 4.70 J EH P64.5 D 0.190 33 709 12345
Color band
Paint stencil
Color identification: In addition to the above marking, each length of Tubing will be color
coded by the following methods:
a: Paint band or bands encircling the pipe at a distance not greater than 0.6m (24 in.)
from the pipe end.
b: The color and number of bands are as follows:
Grade J-55One bright green band. Grade N-80One red band.
#When so specified in the purchase order, the length is shown in feet and inches.
FOR FURTHER DETAILS OF MARKING OF MARUICHI TUBING, PLEASE REFER TO OUR
MARKING SPECIFICAION SHEET.
Coating:
Unless otherwise ordered, pipe shall be given a mill-coating for protection from rust while in
transit.
Standard
Steel-banded.
packing:
Export
marking:
Two metal tags bearing export marks are fastened to each lift bundle.
Flattening test:
Mill-inspection
hydrostatic test:
Permissible
variations
in
dimensions,
weights,
and
lengths:
Drift test:
P max.
S max.
0.030
0.030
0.030
0.030
Yield strength
Tensile Strength,
Elongation, min.%
min.psi(MPa)
mas.psi(MPa)
min.psi(MPa)
in 2 in. (50.80mm)
Grade J-55 55000(379)
80000(552)
75000(517)
*
Grade N-80 80000(552)
110000(758)
100000(689)
*
*The minimum elongation (e) in 2 in. shall be determined by the following English formula.
Where: A = cross sectional area of the tensile test
A0.2
specimen in square inches.
e = 0.9
U
U = specified tensile strength, psi.
The flattening test shall be made on all grades of welded pipe with D/t ratios as shown in table
below. Test specimens shall be rings or crop ends not less than 2-1/2 in. (63.5mm) long from
each end of each length of pope, and shall be flattened with the weld at 0 degrees and, at the
discretion of the inspector, also at 90 degrees until opposite walls of the pipe meet. No cracks
or breaks shall occur anywhere in the specimen until the distance the plates is less than that
specified in the table below nor shall evidence of poor texture, incomplete fusion in the weld,
laminations, burnt metal, or extruded metal develop during the entire flattening process.
Distance between plates for flattening tests
Grade
D/t Ratio
Distance between plates, max., in. or mm
J-55
16 and over
0.65D
3.93 to 16
D(0.98-0.0206D/t)
Less than 3.93
D(1.104-0.0518D/t)
N-80
9 to 28
D(1.074-0.0194d/t)
D=outside diameter of pipe, in in. or mm. t=wall thickness of pipe, in in. or mm.
Each length of plain-end pipe shall withstand, without leakage, a mill inspection hydrostatic
test to at least the pressure tabulated on pages 3 and 4, unless specifically limited by the
purchaser, or the alternate or higher pressure as agreed upon between the purchaser and the
manufacture.
Grade J-55
Grade N-80
42
d = inside diameter of pipe
d-3/32
Weld bead
Nondestructive
The welded seam of Tubing furnished to this specification shall be inspected nondestructively
inspection
in full length (100 percent) by Ultrasonic Testing and Magnetic Leakage Flux Testing methods.
# Usually MRUICHI pipes are contracted for uniform lengths, with a tolerance of plus and minus 2 in. for Tubing.
API 5CT TUBING with Plain Ends
Labels
1
Outside
Nominal linear
Wall
Inside
Calculated
dia.
masses
thickness
dia.
mass
Non-upset
Plain end
NU
kg/m
pe
mm
mm
mm
kg/m
No. of Lengths
in one Lift
(Standard condition)
1.050
1.14
26.67
1.70
2.87
20.93
1.68
127
1.050
1.48
26.67
2.20
3.91
18.85
2.19
79
1.315
1.70
33.40
2.53
3.38
26.64
2.50
79
1.315
2.19
33.40
3.26
4.55
24.30
3.24
61
1.660
2.09
42.16
3.18
35.80
3.06
61
1.660
2.30
42.16
3.42
3.56
35.04
3.39
61
1.660
3.03
42.16
4.51
4.85
32.46
4.46
48
1.900
2.40
48.26
3.18
41.90
3.54
48
1.900
2.75
48.26
4.09
3.68
40.90
4.05
48
1.900
3.65
48.26
5.43
5.08
38.10
5.41
33
2.063
3.24
52.40
3.96
44.48
4.73
44
2.063
4.50
52.40
5.72
40.96
6.58
33
2-3/8
4.00
60.32
5.95
4.24
51.84
5.86
33
2-3/8
4.60
60.32
6.85
4.83
50.66
6.61
33
2-7/8
6.40
73.02
9.52
5.51
62.00
9.17
24