Académique Documents
Professionnel Documents
Culture Documents
Falk UltraMax
A Practical Alternative for Both Gearmotor & Parallel Shaft Drives
The fight for productivity has a brand new contender: the Falk UltraMax.
The UltraMax drive delivers all the performance of a parallel shaft gear
drive, with the economy of a gearmotor.
Designed to meet the tough challenges of medium and heavy-duty
concentric gear drive operation, UltraMax gives you everything you choose
Rexnord equipment for outstanding design, durability, long life,
easy maintenance, and overall efficiency.
UltraMax comes in ten sizes, with an output torque range of 282 Nm
through 67 800 Nm, or 2500 lb.-in. through 600,000 lb.-in.
With UltraMax, you get more power for your dollar, with savings of
up to 30% over a comparably rated parallel shaft gear drive.
And, as always, when you team up with Rexnord, you are assured of
application and delivery assistance, backed up by service and support
where and when you need it.
Falk UltraMax. Performance you can rely on, round after round.
Optimized Design
orque - lb-in
(Nm)
0,000,000
113 300 Nm)
Parallel-Shaft
1,000,000
1130 300 Nm)
UltraMax
100,000
(11 300 Nm)
10,000
(1130 Nm)
1,000
(1 130 Nm)
100
(11,3 Nm)
10
(1,13 Nm)
Gearmotor
Superior Availability
UltraMax delivers the power and
reliability of a parallel shaft drive
with the availability of a gearmotor.
With Rexnords local Finished
Assembly Program, Rexnord
distributors can build and ship
finished UltraMax drives within
hours.
And the large UltraMax inventory at
regional Rexnord Distribution
Centers ensures quick delivery
regardless of size, ratio, or
accessories.
World-Wide Application
Economical, pre-engineered
accessories such as motor brackets,
motor mounts and flanged motor
adapters are readily available to suit
both NEMA and IEC frame motors.
Motor Brackets
Motor Mounts
Slide Bases
Motor Adapters
Motor Plates
Coupling Guards
Electric Fans
Shaft Fans
Cooling Tubes
Backstops
Basic Information
Safety Notes
Falk Gear Drives The Falk and Rexnord name on the gear drive
is the purchasers assurance that the drive was engineered, rated
and manufactured to sound design practices.
When one prime mover drives two pieces of equipment, one of
which is either a standard Falk/Rexnord geared drive or a
customer standard geared drive, the division of power between
each machine is the responsibility of the customer. The power
supplied to the geared drive must be equal to or less than the
power for which the drive was selected using the appropriate
service factor for the application. The customer must also assume
the responsibility of isolating the geared drive from any vibratory
or transient load induced by the driven equipment.
Copyright 1981, 2006. Rexnord Industries, LLC. All Rights Reserved. Litho in U.S.A. FALK,
FREEDOM, LIFELIGN, OMNIBOX, ORANGE PEEL, QUADRIVE, RAM, RENEW, REXNORD,
SPEED QUOTE, SPEED LINE, STEELFLEX, TA TAPER, TRUE HOLD, ULTRAMITE, and
ULTRAMAX, and WRAPFLEX are registered trademarks. DRIVE ONE and TRUE TORQUE
are trademarks of the Falk Corporation.
The contents of this selection guide are subject to change without notice or obligation.
Information contained herein should be confirmed before placing orders.
Rexnord Industries, LLC, 1981, 2006.
(311-110) 5
6 (311-110)
Non-Standard Motors
Motor Brackets
Mounting Positions
UltraMax drives can be modified to permit mounting in positions
other than conventional floor mounting. Some of these include
ceiling, wall and various inclined vertical and tilted positions.
Consult the Factory to determine what modifications are required
for your specific application.
L.S.
END
VIEW
OUTPUT SHAFT UP
TILTED
DRIVE
SIZE
H
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
Double Reduction
INCLINED
Triple Reduction
Quadruple Reduction
Double Reduction
Triple Reduction
DRIVE
SIZE
Quadruple Reduction
Left Hand
Right Hand
Left Hand
Right Hand
Left Hand
Right Hand
L.S. Shaft
Down
L.S. Shaft
Up
L.S. Shaft
Down
L.S. Shaft
Up
L.S. Shaft
Down
L.S. Shaft
Up
5
2
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
2
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
...
10
5
5
5
5
5
5
5
5
...
5
5
5
5
5
5
5
5
5
5
2
5
5
5
5
5
5
5
5
10
10
2
2
2
2
2
2
2
2
5
2
2
2
5
5
5
5
5
5
10
10
2
2
2
2
2
2
2
2
...
2
2
2
2
5
5
5
5
5
...
10
2
2
2
2
2
2
2
2
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
H Maximum limits shown above apply to standard Type FC/FZ drives without modification. For applications requiring higher tilt or incline angles, Refer to Factory.
Oil level must be checked when drive is in the tilted or inclined position.
Size 2060-2130 drives: dipstick must be located on high side of drive as shown in picture.
(311-110) 7
Service Factors
Service Factor
I
II
III
1.00
1.41
2.00
Service
Industry
Service Factors
UltraMax drives may be selected by Service Factor or Load
Classification. Selections may vary, so compare Service Factor
against Load Classification on Pages 10 or 11. Selecting the
lowest Service Factor from Table 1 will result in the most
economical selection.
A gear drive is rated to a specific application by the use of Service
Factor. Each application has its conditions and operating requirements.
These have been analyzed and catalogued. Numerical values, based
on field experience, have been assigned to these classifications for
intermittent service of 3 to 10 hours per day and for service over 10
hours per day and also for the type of prime mover. . .electric motor or
engine. Values for most applications are listed by Application on Page
9, Table 4 and by Industry at right, Table 3. Refer unlisted applications
to the Factory.
Since most industrial applications are electric motor driven, Service
Factors are based on the use of electric motors. These factors can be
easily converted to engine-drive factors as outlined in Table 2 below.
Service Factors are based on the assumption that the system is free of
dynamic vibrations, as explained in the Basic Information section, and
that maximum momentary or starting loads do not exceed 200% of
the rated load. Refer applications subject to repetitive shocks and
applications where exceedingly high energy load must be absorbed,
as when stalling, refer to the Factory for special considerations.
3 to 10 Hours
per Day
Over 10 Hours
per Day
Multi-Cyl.
Engine
Multi-Cyl.
Engine
Motor
Multi-Cyl.
Engine
1.00 (Class I)
1.25
1.41 (Class II)
1.50
1.75
2.00 (Class III)
1.25
1.50
1.75
1.75
2.00
2.25
1.50
1.75
2.00
2.00
2.25
2.50
1.00
1.00
1.25
1.25
1.50
1.75
1.00
1.25
1.50
1.50
1.75
2.00
Intermittent Up to
3 Hours per Day
For applications operating one half hour or less per day and applications driven by
single cylinder engines, refer to Factory.
These service factors are based on the assumption that the system is free from
serious critical and torsional vibrations and that maximum momentary or starting
loads do not exceed 200% of the normal load.
8 (311-110)
3 to Over
10 10
Hour Hour
1.00
1.25
1.00
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.50
Service
Industry
Embosser . . . . . . . . . . . . . . .
Extruder . . . . . . . . . . . . . . . .
Fourdrinier RollsLumpbreaker,
Wire
Turning, Dandy & Return Rolls. . . .
Jordan . . . . . . . . . . . . . . . . .
Kiln Drive . . . . . . . . . . . . . . .
Mt. Hope & Paper Rolls . . . . .
Platter . . . . . . . . . . . . . . . . . .
Presses (Felt & Suction) . . . . . .
Pulper (Continuous) . . . . . . . .
Repulper (Heavy Shock) . . . . .
Reel (Surface Type) . . . . . . . .
Screens
Chip & Rotary . . . . . . . . . . .
Vibrating . . . . . . . . . . . . . .
Size Press . . . . . . . . . . . . . . .
Super Calenders l . . . . . . . . .
Thickener & Washer
AC Motor . . . . . . . . . . . . . .
DC Motor. . . . . . . . . . . . . .
Vacuum Pumps . . . . . . . . . . .
Wind & Unwind Stand . . . . . .
Winders (Surface Type). . . . . .
t Yankee Dryers . . . . . . . . . . . .
PLASTIC INDUSTRY
Batch Drop Mill, 2 smooth rolls
Calenders . . . . . . . . . . . . . . .
Compounding Mills . . . . . . . .
Continuous Feed, Holding &
Blend Mill . . . . . . . . . . . . . . .
Extruders . . . . . . . . . . . . . . . .
Variable Speed Drive. . . . . .
Fixed Speed Drive . . . . . . . .
Intensive Internal Mixers
Batch Mixers . . . . . . . . . . . .
Continuous Mixers . . . . . . .
RUBBER INDUSTRY
Batch Drop Mill, 2 smooth rolls
Calenders . . . . . . . . . . . . . . .
Cracker, 2 corrugated rolls. . .
Cracker Warmer2 roll,
3 to Over
10 10
Hour Hour
...
...
1.25
1.50
...
1.25
...
...
...
...
...
...
...
...
1.50
1.50
1.25
1.50
1.25
2.00
2.00
1.25
...
...
...
...
1.50
2.00
1.25
1.25
...
...
...
...
...
...
1.50
1.25
1.50
1.25
1.25
1.25
1.25
1.50
1.25
1.25
1.50
1.25
1.25
1.25
1.50
1.50
1.75
1.50
1.50
1.75
1.75
1.50
1.75
1.50
1.50
1.50
2.00
1.50
1.50
2.00
1.75 1.75
1 corrugated roll . . . . . . . . . .
Extruders
Continuous Screw Operation 1.75 1.75
Intermittent Screw Operation 1.75 1.75
Holding, Feed & Blend Mill2
1.25 1.25
Roll
Intensive Internal Mixers
Batch Mixers . . . . . . . . . . . . 1.75 1.75
Continuous Mixers . . . . . . . 1.50 1.50
Mixing Mill2 smooth rolls . .
(if corrugated rolls are used, use 1.50 1.50
Cracker Warmer service factors)
Refiner2 roll . . . . . . . . . . . . 1.50 1.50
SEWAGE DISPOSAL
Bar Screens . . . . . . . . . . . . . . 1.25 1.25
Chemical Feeders . . . . . . . . . 1.25 1.25
Collectors . . . . . . . . . . . . . . . 1.25 1.25
Dewatering Screens . . . . . . . . 1.50 1.50
Scum Breakers. . . . . . . . . . . . 1.50 1.50
Slow or Rapid Mixers . . . . . . . 1.50 1.50
Thickeners. . . . . . . . . . . . . . . 1.50 1.50
Vacuum Filters. . . . . . . . . . . . 1.50 1.50
SUGAR INDUSTRY
Cane Knives, Crushers . . . . . . . . .
1.75
Mills (low speed end) . . . . . . . 1.75 1.75
TEXTILE INDUSTRY
Batchers, Calenders . . . . . . . . 1.25 1.50
Card Machines . . . . . . . . . . . 1.25 1.50
Dry Cans, Dryers . . . . . . . . . . 1.25 1.50
Dyeing Machinery . . . . . . . . . 1.25 1.50
Knitting Machinery . . . . . . . . . Refer to Factory
Looms, Mangles, Nappers,
1.25 1.50
Pads
Range Drives . . . . . . . . . . . . . Refer to Factory
Slashers, Soapers, Spinners,
Tenter Frames, Washers, Winders 1.25 1.50
WINDLASS . . . . . . . . . . . . Refer to Factory
H Service Factors for paper mill applications are applied to the nameplate rating of
the electric drive motor at the motor rated base speed and are consistent with
those shown in TAPPI standards.
t Anti-friction bearings only.
l A service factor of 1.00 may be applied at base speed of a super calender
operating over a speed range of part constant hp and part constant torque where
the constant hp speed range is greater than 1.5 to 1. A service factor of 1.25 is
applicable to super calenders operating at constant torque over the entire speed
range or where the constant hp speed range is less than 1.5 to 1.
3 to Over
10
10
Hour Hour
Service
Application
3 to Over
10
10
Hour Hour
AGITATORS
s CONVEYORSUniformly
Pure Liquids . . . . . . . . . . . . . . 1.00
1.25
loaded or Fed:
Liquids & Solids . . . . . . . . . . . 1.25
1.50
Apron, Bucket . . . . . . . . . . . 1.25
1.50
Liquids-Variable Density . . . . . 1.25
1.50
Assembly, Belt, Chain, Flight,
APRON CONVEYORS
Oven, Screw. . . . . . . . . . . . 1.25
1.25
Uniformly Loaded or Fed. . . . . 1.25
1.50
s CONVEYORSHeavy Duty,
Heavy Duty . . . . . . . . . . . . . . 1.25
1.50
Not Uniformly Fed
1.50
APRON FEEDERS . . . . . . . . . 1.25
Apron, Assembly, Belt, Bucket, 1.25
ASSEMBLY CONVEYORS
1.50
Chain, Flight, Oven, Screw . .
Uniformly Loaded or Fed. . . . . 1.25
1.25
CONVEYORSSevere
Duty
Heavy Duty . . . . . . . . . . . . . . 1.25
1.50
Live Roll . . . . . . . . . . . . . . . . . Refer to Factory
BALL MILLS . . . . . . . . . . . . See Mills, Rotary
Reciprocating Shaker . . . . . . . 1.75
2.00
2.00
BARGE HAUL PULLERS. . . . . 1.75
COOKERS (Brewing &
1.25
1.25
BARKING
Distilling), (food). . . . . . . .
Drums (Coupling Connected) . . . .
2.00
Refer
to
Factory
COOLING TOWER FANS .
Mechanical . . . . . . . . . . . . . . . . .
2.00
1.25
s CRANES
BAR SCREENS (Sewage) . . . 1.25
Dry Dock Cranes, Main Hoist,
1.50
BATCHERS (Textile) . . . . . . . 1.25
Bridge and Trolley Travel. . . . . Refer to Factory
BELT CONVEYORS
CRUSHERS
Uniformly Loaded or Fed. . . . . 1.25
1.25
Ore or Stone . . . . . . . . . . . . . 1.75
2.00
Heavy Duty . . . . . . . . . . . . . . 1.25
1.50
Sugar . . . . . . . . . . . . . . . . . . . . .
1.75
1.50
BELT FEEDERS. . . . . . . . . . . . 1.25
DEWATERING SCREENS
1.50
1.50
BENDING ROLLS (Machine). 1.25
(Sewage) . . . . . . . . . . . . . . 1.50
BLOWERS
1.25
DISC FEEDERS . . . . . . . . . . . 1.00
Centrifugal. . . . . . . . . . . . . . . 1.25
1.25
DISTILLING . . . . . . . . . . . . . . See Table 3
Lobe . . . . . . . . . . . . . . . . . . . 1.25
1.50
Vane . . . . . . . . . . . . . . . . . . . 1.25
1.50
DOUBLE ACTING PUMPS
2 or more Cylinders . . . . . . . . 1.25
1.50
1.25
BOTTLING MACHINERY. . . . 1.00
Single Cylinder . . . . . . . . . . . . Refer to Factory
See
Table
3
BREWING . . . . . . . . . . . . . . .
1.50
DOUGH MIXER (Food) . . . . . 1.25
2.00
BRICK PRESS (Clay Working) 1.75
DRAW BENCH (Metal Mills)
BRIQUETTE MACHINES
1.25
1.50
Carriage & Main Drive . . . . .
1.75
2.00
(Clay Working) . . . . . . . . .
DREDGES . . . . . . . . . . . . . . . See Table 3
BUCKET
Conveyors Uniform. . . . . . . . . 1.25
1.50
DRY DOCK CRANES . . . . . Refer to Factory
Conveyors Heavy Duty . . . . . . 1.25
1.50
DRYERS & COOLERS (Mills, . . .
Elevators Continuous . . . . . . . 1.25
1.50
1.50
Rotary). . . . . . . . . . . . . . . .
Elevators Uniform . . . . . . . . . . 1.25
1.50
Elevators Heavy Duty . . . . . . . 1.25
1.50
DYEING MACHINERY
CALENDERS
1.50
(Textile) . . . . . . . . . . . . . . . 1.25
Rubber and Plastic . . . . . . . . . See Table 3
ELEVATORS
Textile . . . . . . . . . . . . . . . . . . 1.25
1.50
Bucket-Uniform Load . . . . . . . 1.25
1.50
Bucket-Heavy Duty . . . . . . . . . 1.25
1.50
1.75
CANE KNIVES. . . . . . . . . . . . . . .
Bucket-Continuous . . . . . . . . . 1.25
1.50
1.25
CAN FILLING MACHINES . . 1.00
Centrifugal Discharge . . . . . . . 1.25
1.25
CARD MACHINES (Textile) . 1.25
CAR DUMPERS . . . . . . . . . . . 1.75
CAR PULLERS . . . . . . . . . . . . 1.25
1.50
2.00
1.50
1.25
1.25
1.25
1.25
1.25
1.50
1.50
1.75
1.75
2.00
1.25
1.25
1.50
1.50
s Escalators . . . . . . . .
s Freight. . . . . . . . . . .
s Gravity Discharge. . .
s Man Lifts, Passenger
.......
.......
.......
.......
Not Approved
Not Approved
1.00
1.25
Not Approved
EXTRUDERS
(Plastic & Rubber) . . . . . . . See Table 3
FANS
Centrifugal. . . . . . . . . . . . . . . 1.25
1.25
Cooling Towers . . . . . . . . . . . Refer to Factory
Forced Draft. . . . . . . . . . . . . . . . .
1.25
Induced Draft . . . . . . . . . . . . . 1.50
1.50
Large (Mine, etc.) . . . . . . . . . . 1.50
1.50
Large lndustrial. . . . . . . . . . . . 1.50
1.50
Light (Small Diameter). . . . . . . 1.00
1.25
FEEDERS
Apron, Belt. . . . . . . . . . . . . . . 1.25
1.50
Disc. . . . . . . . . . . . . . . . . . . . 1.00
1.25
Reciprocating . . . . . . . . . . . . . 1.75
2.00
Screw . . . . . . . . . . . . . . . . . . 1.25
1.50
FLIGHT CONVEYORS
Uniform . . . . . . . . . . . . . . . . . 1.25
1.25
Heavy . . . . . . . . . . . . . . . . . . 1.25
1.50
See
Table
3
FOOD INDUSTRY . . . . . . . . .
GENERATORS (Not
1.00
1.25
Welding) . . . . . . . . . . . . . .
GRAVITY DISCHARGE
1.00
1.25
ELEVATORS . . . . . . . . . . . .
2.00
HAMMER MILLS . . . . . . . . . . 1.75
Service
Application
3 to Over
10
10
Hour Hour
s HOISTS
Heavy Duty . . . . . . . . . . . . . .
Medium Duty . . . . . . . . . . . . .
Skip Hoist . . . . . . . . . . . . . . .
INDUCED DRAFT FANS . . . .
1.75
1.25
1.25
1.50
2.00
1.50
1.50
1.50
Service
Application
3 to Over
10
10
Hour Hour
PUMPS
Centrifugal. . . . . . . . . . . . . . . 1.25
1.25
Proportioning . . . . . . . . . . . . . 1.25
1.50
Reciprocating
Single Act., 3 or more Cyl.. . 1.25
1.50
Double Act., 2 or more Cyl. . 1.25
1.50
Single Act., 1 or 2 Cyl. . . . . Refer to Factory
Double Acting, 1 Cyl. . . . . . Refer to Factory
Rotary: Gear, Lobe, Vane . . . . 1.00
1.25
PUNCH PRESSES (Gear
1.75
2.00
Driven) . . . . . . . . . . . . . . .
RECIPROCATING
2.00
Conveyors & Feeders . . . . . . 1.75
RECIPROCATING
COMPRESSORS
Multi-Cylinder . . . . . . . . . . . . 1.50
1.75
Single Cylinder . . . . . . . . . . . . 1.75
2.00
See
Mills,
Rotary
ROD MILLS . . . . . . . . . . . .
ROTARY
Pumps . . . . . . . . . . . . . . . . . . 1.00
1.25
Screens (Sand or Gravel). . . . . 1.25
1.50
RUBBER & PLASTICS
INDUSTRIES . . . . . . . . . . . See Table 3
Selection of Rexnord products for applications whose primary purpose is the transportation of people is not approved. This includes such applications as freight or passenger elevators,
escalators, man lifts, work lift platforms and ski tows and ski lifts. If the primary purpose of the application is material conveyance and occasionally people are transported, the
Rexnord warranty may remain in effect provided the design load conditions are not exceeded and certification to the appropriate safety codes and load conditions has been
obtained by the system designer or end user from the appropriate enforcement authorities.
Contact your local Rexnord representative for proper selection of a Falk RAM mixer drive.
(311-110) 9
Service Factor
I
II
III
1.00
1.41
2.00
3 to Over
10 10
Hour Hour
I
II
II
II
II
II
II
II
III
III
III
III
II
II
II
II
See Brewing
II
II
III
III
III
III
III
II
II
II
III
III
III
III
II
II
I
II
II
Cereal Cookers
I
II
Dough Mixers, Meat Grinders .
II
II
LUMBER INDUSTRY
BarkersSpindle Feed . . . . . .
II
III
BarkersMain Drive . . . . . . .
III
III
Carriage Drive . . . . . . . . . . . . Refer to Factory
Conveyors
Burner . . . . . . . . . . . . . . . .
II
III
Main or Heavy Duty . . . . . .
II
III
Main Log . . . . . . . . . . . . . .
III
III
Re-Saw Merry-Go-Round . . .
II
III
Slab . . . . . . . . . . . . . . . . . .
III
III
Transfer . . . . . . . . . . . . . . .
II
III
ChainsFloor. . . . . . . . . . . .
II
III
ChainsGreen . . . . . . . . . . .
II
III
Cut-Off SawsChain & Drag.
II
III
Debarking Drums . . . . . . . . .
III
III
FeedsEdger . . . . . . . . . . . .
II
III
FeedsGang . . . . . . . . . . . .
III
III
FeedsTrimmer . . . . . . . . . .
II
III
Log Deck . . . . . . . . . . . . . . .
III
III
Log HaulsIncline, Well Type
III
III
Log Turning Devices. . . . . . . .
III
III
Planer Feed. . . . . . . . . . . . . .
II
III
Planer Tilting Hoists . . . . . . . .
II
III
RollsLiveOff Bearing
Roll Cases. . . . . . . . . . . . . . .
III
III
Sorting Table, Tipple Hoist . . .
II
III
TransfersChain & Craneway
II
III
Tray Drives . . . . . . . . . . . . . .
II
III
OIL INDUSTRY
Chillers . . . . . . . . . . . . . . . . .
II
II
Oil Well Pumping . . . . . . . . . . Refer to Falk
II
II
II
II
Service
Industry
PAPER MILLS
Agitator (Mixer) . . . . . . . . . . .
BarkerAuxiliariesHyd.. . . .
Barker, Mechanical . . . . . . . .
Barking Drum . . . . . . . . . . . .
Beater & Pulper . . . . . . . . . . .
Bleacher . . . . . . . . . . . . . . . .
t Calenders . . . . . . . . . . . . . . .
t CalendarsSuper
Converting Mach.Except
.....................
Cutters-Platers . . . . . . . . . . . .
Conveyors. . . . . . . . . . . . . . .
Couch . . . . . . . . . . . . . . . . .
Cutters, Platers . . . . . . . . . . .
Cylinders. . . . . . . . . . . . . . . .
t Dryers . . . . . . . . . . . . . . . . . .
Felt Stretchers . . . . . . . . . . . .
Felt Whippers . . . . . . . . . . . .
Jordans. . . . . . . . . . . . . . . . .
Log Haul. . . . . . . . . . . . . . . .
Presses . . . . . . . . . . . . . . . . .
Pulper (Continuous) . . . . . . . .
Repulper (Heavy Shock) . . . . .
Stock Chests . . . . . . . . . . . . .
Suction Rolls . . . . . . . . . . . . .
Washers & Thickeners . . . . . .
Winders . . . . . . . . . . . . . . . .
RUBBER INDUSTRY
Mixer . . . . . . . . . . . . . . . . . .
Rubber Calender . . . . . . . . . .
Rubber Mill (2 or more) . . . . .
Sheeter . . . . . . . . . . . . . . . . .
Tire Building Machines . . . . . .
Tire, Tube Press Openers . . . .
Tubers & Strainers . . . . . . . . .
SEWAGE DISPOSAL
Aerators . . . . . . . . . . . . . . . .
Bar Screens . . . . . . . . . . . . . .
Chemical Feeders . . . . . . . . .
Collectors . . . . . . . . . . . . . . .
Dewatering Screens . . . . . . . .
Grit Collectors. . . . . . . . . . . .
Scum Breakers. . . . . . . . . . . .
Slow or Rapid Mixers . . . . . . .
Sludge Collectors. . . . . . . . . .
Thickeners. . . . . . . . . . . . . . .
Vacuum Filters. . . . . . . . . . . .
TEXTILE INDUSTRY
Batchers, Calenders . . . . . . . .
Card Machines . . . . . . . . . . .
Cloth Finishing Machines,
Calenders, Dryers, Pads,
Tenters, Washers) . . . . . . . . .
Dry Cans . . . . . . . . . . . . . . .
Dyeing Machinery . . . . . . . . .
Knitting Machinery . . . . . . . . .
Looms, Mangles, Nappers . . .
Range Drives . . . . . . . . . . . . .
Soapers, Spinners . . . . . . . . .
Tenter Frames . . . . . . . . . . . .
Winders . . . . . . . . . . . . . . . .
3 to Over
10 10
Hour Hour
II
II
III
III
III
II
II
II
II
II
II
II
III
II
II
II
III
II
III
II
III
III
II
II
II
II
III
III
II
II
II
II
II
II
Refer to Factory
Refer to Factory
II
II
Refer to Factory
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
II
Refer to Falk
II
II
Refer to Falk
II
II
II
II
II
II
10 (311-110)
AERATORS
Refer to Falk
AGITATORS
Paper Mills. . . . . . . . . . . . . . .
II
II
Pure Liquids . . . . . . . . . . . . . .
I
II
Liquids & Solids . . . . . . . . . . .
II
II
Liquids-Variable Density . . . . .
II
II
APRON CONVEYORS
Uniformly Loaded or Fed. . . . .
II
II
Heavy Duty . . . . . . . . . . . . . .
II
II
APRON FEEDERS . . . . . . . . .
II
II
ASSEMBLY CONVEYORS
Uniformly Loaded or Fed. . . . .
II
II
Heavy Duty . . . . . . . . . . . . . .
II
II
BALL MILLS . . . . . . . . . . . . . .
III
III
BARGE HAUL PULLERS. . . . .
III
III
BARKING
Drums . . . . . . . . . . . . . . . . .
III
Hydraulic Auxiliaries . . . . . . . .
III
Mechanical . . . . . . . . . . . . . .
III
BAR SCREENS (Sewage) . . .
II
II
BATCHERS (Textile)
II
II
II
BELT CONVEYORS
Uniformly Loaded or Fed. . . . .
II
II
Heavy Duty . . . . . . . . . . . . . .
II
II
BELT FEEDERS. . . . . . . . . . . .
II
II
BENDING ROLLS (Machine).
II
II
BLEACHERS (Paper) . . . . . . .
II
BLOWERS
Centrifugal. . . . . . . . . . . . . . .
II
II
Lobe . . . . . . . . . . . . . . . . . . .
II
II
Vane . . . . . . . . . . . . . . . . . . .
II
II
BOTTLING MACHINERY. . . .
I
II
BREWING . . . . . . . . . . . . . . . See Table 6
BRICK PRESS (Clay Working)
III
III
BRIQUETTE MACHINES
(Clay Working) . . . . . . . . .
III
III
BUCKET
Conveyors Uniform. . . . . . . . .
II
II
Conveyors Heavy Duty . . . . . .
II
II
Elevators Continuous . . . . . . .
II
II
Elevators Uniform . . . . . . . . . .
II
II
Elevators Heavy Duty . . . . . . .
II
II
CALENDERS
Rubber . . . . . . . . . . . . . . . . .
II
II
Textile . . . . . . . . . . . . . . . . . .
II
II
CANE KNIVES. . . . . . . . . . . .
II
III
CAN FILLING MACHINES . .
I
II
CARD MACHINES (Textile) .
II
II
CAR DUMPERS . . . . . . . . . . .
III
CAR PULLERS . . . . . . . . . . . .
II
Application
Service
3 to Over
10
10
Hour Hour
Application
CONCRETE MIXERS
Continuous . . . . . . . . . . . . . .
Intermittent. . . . . . . . . . . . . . .
CONVERTING MACHINES
(Paper) . . . . . . . . . . . . . . . . .
s CONVEYORSUniformly
Loaded or Fed:
Apron, Assembly, Belt, Bucket,
Chain, Flight, Oven, Screw . .
s CONVEYORSHeavy Duty,
Not Uniformly Fed
Apron, Assembly, Belt, Bucket,
Chain, Flight, Oven, Screw . .
Live Roll (Package) . . . . . . .
Reciprocating, Shaker . . . . .
COOKERS (Brewing &
Distilling), (food). . . . . . . .
3 to Over
10
10
Hour Hour
II
II
II
II
II
II
II
II
III
II
II
III
II
II
Refer to Factory
COOLING TOWER FANS
COUCH (Paper) . . . . . . . . . .
II
s CRANES
& HOISTS
Main Hoists
Heavy Duty. . . . . . . . . . . . .
III
III
Medium Duty . . . . . . . . . . .
II
II
Reversing . . . . . . . . . . . . . . . .
II
II
Skip Hoists . . . . . . . . . . . . . . .
II
II
Trolley Drive. . . . . . . . . . . . . .
II
II
Bridge Drive. . . . . . . . . . . . . .
II
II
CRUSHERS
Ore or Stone . . . . . . . . . . . . .
III
III
CUTTERS (Paper) . . . . . . . . . .
III
CYLINDERS (Paper) . . . . . . . .
II
DEWATERING SCREENS
(Sewage) . . . . . . . . . . . . . .
II
II
DISC FEEDERS . . . . . . . . . . .
I
II
DISTILLING . . . . . . . . . . . . . . See Table 6
DOUBLE ACTING PUMPS
2 or more Cylinders . . . . . . . .
II
II
Single Cylinder . . . . . . . . . . . . Refer to Factory
DOUGH MIXER (Food) . . . . .
II
II
DRAW BENCH (Metal Mills)
Carriage & Main Drive . . . . .
III
III
DREDGES . . . . . . . . . . . . . . . See Table 6
DRYERS & COOLERS
(Mills, Rotary) . . . . . . . . . .
II
II
DYEING MACHINERY
(Textile) . . . . . . . . . . . . . . .
II
II
ELEVATORS
Bucket-Uniform Load . . . . . . .
II
II
Bucket-Heavy Duty . . . . . . . . .
II
II
Bucket-Continuous . . . . . . . . .
II
II
Centrifugal Discharge . . . . . . .
II
II
Escalators . . . . . . . . . . . . . . . Not Approved
Freight . . . . . . . . . . . . . . . . . Not Approved
Gravity Discharge. . . . . . . . . .
I
II
Man Lifts, Passenger . . . . . . . Not Approved
FANS
Centrifugal. . . . . . . . . . . . . . .
II
II
Cooling Towers . . . . . . . . . . . Refer to Factory
Forced Draft. . . . . . . . . . . . . .
II
II
Induced Draft . . . . . . . . . . . . .
II
II
Large (Mine, etc.) . . . . . . . . . .
II
II
Large lndustrial. . . . . . . . . . . .
II
II
Light (Small Diameter). . . . . . .
I
II
FEEDERS
Apron, Belt. . . . . . . . . . . . . . .
II
II
Disc. . . . . . . . . . . . . . . . . . . .
I
II
III
III
Reciprocating . . . . . . . . . . . . .
Screw . . . . . . . . . . . . . . . . . .
II
II
FELT
Stretchers (Paper) . . . . . . . . . .
II
Whippers (Paper) . . . . . . . . . .
III
FLIGHT CONVEYORS
Uniform . . . . . . . . . . . . . . . . .
II
II
Heavy . . . . . . . . . . . . . . . . . .
II
II
See
Table
6
FOOD INDUSTRY . . . . . . . . .
3 to Over
10
10
Hour Hour
FORMING MACHINES
(Metal Mills) . . . . . . . . . . .
III
III
GENERATORS (Not
Welding) . . . . . . . . . . . . . .
I
II
GRAVITY DISCHARGE
ELEVATORS . . . . . . . . . . . .
I
II
GRIT COLLECTORS
(Sewage) . . . . . . . . . . . . . .
II
II
HAMMER MILLS . . . . . . . . . .
III
III
INDUCED DRAFT FANS . . . .
II
II
KILNS (Mills, Rotary) . . . . . .
II
II
Cement . . . . . . . . . . . . . . . . . Refer to Factory
LAUNDRY WASHERS . . . . . .
II
III
LAUNDRY TUMBLERS . . . . .
II
II
LINE SHAFTS
Heavy Shock Load . . . . . . . . .
III
III
Moderate Shock Load . . . . . . .
II
II
Uniform Load . . . . . . . . . . . . .
I
II
LIVE ROLL CONVEYORS . .
Package . . . . . . . . . . . . . . . .
II
II
LOBE BLOWERS OR
COMPRESSORS . . . . . . . . .
II
II
LOG HAULS (Paper &
Lumber). . . . . . . . . . . . . . .
III
III
LOOMS (Textile) . . . . . . . . . .
II
II
See
Table
6
LUMBER INDUSTRY . . . . . . .
MACHINE TOOLS
Auxiliary Drives. . . . . . . . . . . .
I
II
Bending Rolls . . . . . . . . . . . . .
II
II
Main Drives . . . . . . . . . . . . . .
II
II
Notching Press (Belted) . . . . . . Refer to Factory
Plate Planers . . . . . . . . . . . . .
III
III
Punch Press (Geared) . . . . . . .
III
III
Tapping machines . . . . . . . . .
III
III
MANGLE (Textile) . . . . . . . . .
II
II
MASH TUBS (Brewing &
Distilling). . . . . . . . . . . . . .
II
MEAT GRINDERS (Food) . . .
II
II
METAL MILLS
Draw Bench Carriages &
Main Drives . . . . . . . . . . . . . .
III
III
Forming Machines . . . . . . . . .
III
III
Pinch, Dryer & Scrubber
Rolls, Reversing. . . . . . . . . . Refer to Factory
Slitters . . . . . . . . . . . . . . . . . .
II
II
Table Conveyors . . . . . . . . . .
Non-Reversing . . . . . . . . . .
III
III
Reversing
Refer to Factory
Wire Drawing & Flattening
Machines. . . . . . . . . . . . . . . .
II
III
Wire Winding Machines . . . . .
II
II
MILLS, ROTARY
Ball, Pebble, Rod . . . . . . . . . .
III
III
Cement Kilns . . . . . . . . . . . . . Refer to Factory
Coolers, Dryers, Kilns . . . . . . .
II
III
Tumbling Barrels . . . . . . . . . .
III
III
MIXER (Also see Agitators)
ConcreteContinuous . . . . . .
II
II
ConcreteIntermittent . . . . . .
II
Constant Density . . . . . . . . . .
II
II
Variable Density . . . . . . . . . . .
II
II
NAPPERS (Textile). . . . . . . . .
II
II
OIL INDUSTRY . . . . . . . . . . . See Table 6
ORE CRUSHERS . . . . . . . . . .
III
III
OVEN CONVEYORS
Uniform . . . . . . . . . . . . . . . . .
II
II
Heavy Duty . . . . . . . . . . . . . .
II
II
PAPER MILLS . . . . . . . . . . . . . See Table 6
PASSENGER ELEVATORS . . Not Approved
PEBBLE MILLS . . . . . . . . . . . .
III
III
PLATE PLANERS . . . . . . . . . .
III
III
PRESSES PAPER. . . . . . . . . . .
II
PROPORTIONING PUMPS . .
II
II
PUG MILLS (Clay) . . . . . . . . .
II
II
Service
Application
3 to Over
10
10
Hour Hour
II
STOKERS . . . . . . . . . . . . . . . .
I
II
STONE CRUSHERS . . . . . . . .
III
III
SUCTION ROLLS (Paper) . . .
II
TABLE CONVEYORS
(Metal Mills)
Non-Reversing . . . . . . . . . . . .
III
III
Reversing . . . . . . . . . . . . . . . . Refer to Factory
TENTER FRAMES (Textile). . .
II
II
TEXTILE INDUSTRY . . . . . . . . See Table 6
THICKENERS (Sewage) . . . .
II
II
TUMBLING BARRELS . . . . . .
III
III
VACUUM FILTERS (Sewage)
II
II
VANE BLOWERS . . . . . . . . . .
II
II
WINCHES (Dredges) . . . . . .
II
WINDERS (Textile)
Paper . . . . . . . . . . . . . . . . . .
II
Textile . . . . . . . . . . . . . . . . . .
II
II
WINDLASS . . . . . . . . . . . . Refer to Factory
WIRE
Drawing Machines . . . . . . . . .
II
III
Winding Machines . . . . . . . . .
II
II
Service
Selection of Rexnord products for applications whose primary purpose is the transportation of people is not approved. This includes such applications as freight or passenger elevators,
escalators, man lifts, work lift platforms and ski tows and ski lifts. If the primary purpose of the application is material conveyance and occasionally people are transported, the
Rexnord warranty may remain in effect provided the design load conditions are not exceeded and certification to the appropriate safety codes and load conditions has been
obtained by the system designer or end user from the appropriate enforcement authorities.
Contact your local Rexnord representative for proper selection of a Falk RAM mixer drive.
(311-110) 11
Example
Reversing Service
Brake Equipped Applications
Oversized Prime Movers
Multi-Speed or Variable Speed Applications
Excessive Ambient Temperatures
Thermal Rating Application Factors
Excessive Overhung Loads or Thrust Loads
Product Modifications
Non-Standard Motors or Prime Movers
Non-Standard Motor Bracket Applications
Non-Horizontal Mounting Positions
How to Select By Quick Selection
1. Determine Service Factor or Load Classification Factor See
Pages 8 & 9 or 10 & 11.
2. Determine Motor Horsepower
3. Determine Drive Output Speed.
4. Select Drive Size Use Quick Selection Tables, Pages 15 thru
31; find the table for your motor horsepower and locate the
correct drive size opposite the nearest output rpm and the
required service factor determined in Steps 1 thru 3.
5. Select Drive Configuration Type FC or FZ, see Pages 58
thru 61.
6. Check Minimum Cooling Required. If a required cooling
accessory is not acceptable check a larger size drive
7. Check Overhung Load Minimum allowable sprocket pitch
diameters are provided for the L.S. Shaft based on the
sprocket being mounted one shaft diameter from the seal
cage and a service factor of unity. Where overhung load is
proportional to torque; e.g., pinion, sprocket, or sheave
applications, adjustment to the published values must be
made based on the required service factor. The pitch diameter
of the sprocket being used must not be less than the value
(Pd) shown. If the sprocket is located at a distance other than
one shaft diameter from the seal cage, refer to the instructions
on Page 48.
8. Check External Thrust Load Thrust loads are provided on
Page 55. If thrust and overhung loads are applied
simultaneously, or if loads exceed these capacities, consult the
Factory.
9. Check Drive Dimensions Pages 58 thru 61.
10. Place the Order How to Order information on Page 14.
12 (311-110)
2060F_2
2070F_2
2080F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2070F_2
Exact
Ratio
HP
Rating
Service
Factor
17.19
17.33
17.34
21.13
20.54
20.98
25.12
25.17
31.08
69.8
102
149
59.3
84.8
117
68.0
96.7
53.1
1.40
2.04
2.98
1.19
1.70
2.34
1.36
1.93
1.06
L.S. Shaft
Minimum
OHL
Cooling
Capacity
Required
(lb)
None
None
None
None
None
None
None
None
None
6500
8500
7480
6500
8500
10200
8500
11000
8500
Minimum
L.S. Shaft
Sprocket
Pitch Dia
9.69
7.41
8.42
11.54
8.82
7.35
10.90
8.42
13.24
Ratio
TYPE
2 050 F Z K 4 A S - 105.9
A 143
FRAME
SIZE
2000
SERIES
MOTOR
MOUNTING
SIZES
BASIC DRIVE
RATIO
H.S. SHAFT
ARRANGEMENT
ADDITIONAL PRODUCT
DESCRIPTION
Seal Option
SEAL OPTION
VARIANCE SYMBOL
MODEL
NO. OF REDUCTIONS
Sizes
2040 thru 2050 Cast iron housings
2060 thru 2130 Fabricated steel housings
Motor Mounting
A
B
C
E
G
H
J
L
S
Drive Arrangement
C
Z
M
A
D
Reductions
2, 3, 4, etc.
Model
A, B, C, etc.
Variance Symbol
A
B
C
D
E
F
G
H
J
K
L
S
Drive w/ backstop
Drive w/ shaft fan
Drive w/ backstop & shaft fan
Drive w/ electric fan
Drive w/ electric fan & backstop
Drive w/ cooling tubes
Drive w/ cooling tubes & backstop
Drive w/ pump & cooler (air)
Drive w/ pump & cooler (air) & backstop
Drive w/ pump & cooler (water)
Drive w/ pump & cooler (water) & backstop
Modified or special drive
(311-110) 13
Drive
A.
B.
C.
D.
E.
F.
G.
H.
Auxiliary Equipment
A. Motors If Rexnord is to furnish, specify complete
information, e.g. current characteristics, enclosure,
modifications, accessories, etc.
B. Couplings Specify size, type, driver or driven hub bore and
keyway size.
C. Backstop Specify direction of rotation of the low speed shaft
(clockwise or counter clockwise) when looking toward the
drive from the low speed end.
D. Motor Mount Specify complete motor information,
required belt centers and mounting arrangement.
E. Motor Plate Specify complete motor, auxiliary equipment
and coupling information.
F. Electric Fan Position
G. Cooling Tube Water Inlet & Outlet Position
H. Coupling Guards Furnish description of couplings or other
equipment to be guarded and all dimensions A-G below.
J. Motor Bracket Specify complete motor information
including motor weight, auxiliary equipment and
coupling information.
A
B
Driven Machine
A.
B.
C.
D.
14 (311-110)
G
D
6.0
5.0
4.0
4.0
3.2
3.2
2.7
2.7
2.2
2.2
2.2
1.8
1.8
1.8
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
2040F_3
2050F_4
2050F_4
2050F_4
2060F_4
2050F_4
2060F_4
2060F_4
2070F_4
2060F_4
2070F_4
2080F_4
2060F_4
2070F_4
2080F_4
159.4
286.1
343.3
417.1
449.4
508.3
543.0
649.5
641.4
795.9
785.9
772.8
965.5
961.2
927.2
2.50
2.49
2.08
1.71
2.80
1.40
2.32
1.94
2.81
1.58
2.29
2.86
1.30
1.86
2.25
2.50
2.49
2.08
1.71
2.80
1.40
2.32
1.94
2.81
1.58
2.29
2.86
1.30
1.86
2.25
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
3400
5250
5250
5250
6500
5250
6500
6500
8500
6500
8500
11000
6500
8500
11000
3.37
4.00
4.80
6.00
4.85
7.50
6.06
7.18
5.49
8.81
6.74
5.21
10.77
8.24
6.36
13.5
11.0
9.0
7.5
6.0
6.0
5.0
5.0
4.0
4.0
4.0
3.2
3.2
3.2
2.7
2.7
2.7
2.2
2.2
2.2
1.8
1.8
1.8
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
2040F_3
2040F_3
2040F_3
2050F_4
2050F_4
2050F_4
2060F_4
2050F_4
2060F_4
2050F_4
2060F_4
2070F_4
2060F_4
2070F_4
2080F_4
2060F_4
2070F_4
2080F_4
2060F_4
2070F_4
2080F_4
2070F_4
2080F_4
2090F_4
105.0
125.0
159.4
187.5
231.5
286.1
296.3
343.3
363.2
417.1
449.4
443.8
543.0
542.7
523.5
649.5
641.4
638.7
795.9
785.9
772.8
961.2
927.2
945.2
3.80
3.16
2.50
3.53
3.08
2.49
4.24
2.08
3.46
1.71
2.80
4.06
2.32
3.30
3.98
1.94
2.81
4.14
1.58
2.29
2.86
1.86
2.25
4.44
2.53
2.11
1.67
2.35
2.05
1.66
2.83
1.39
2.31
1.14
1.87
2.71
1.55
2.20
2.65
1.29
1.87
2.76
1.05
1.53
1.91
1.24
1.50
2.96
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
3400
3400
3400
5250
5250
5250
6500
5250
6500
5250
6500
8500
6500
8500
11000
6500
8500
11000
6500
8500
11000
8500
11000
14000
3.37
4.12
5.05
4.00
4.80
6.00
4.85
7.20
5.82
9.00
7.27
5.56
9.09
6.95
5.37
10.77
8.24
6.36
13.22
10.11
7.81
12.35
9.55
7.50
H Drive selections found in the Quick Selection Tables are based on an ambient temperature of 80F(27C) at sea level (0 to 2500 ft.). If the environmental factors differ for your
specific application, the application adjusted thermal rating must be calculated to verify the drive selection. See the Quick Selection example on Page 12 and the application
adjusted thermal rating procedure on Page 42.
Published values of overhung load and sprocket pitch diameter are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is
proportional to torque (i.e. pinion, sprocket, or sheave applications) adjustment to the published values must be made based on the minimum required service factor. Refer to
Page 48 for additional information.
(311-110) 15
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
25.0
20.0
16.5
13.5
13.5
11.0
11.0
9.0
7.5
7.5
6.0
6.0
5.0
5.0
5.0
4.0
4.0
4.0
3.2
3.2
3.2
2.7
2.7
2.2
2.2
2.2
1.8
1.8
1.8
2040F_3
2040F_3
2040F_3
2040F_3
2050F_3
2040F_3
2050F_3
2050F_4
2050F_4
2060F_4
2050F_4
2060F_4
2050F_4
2060F_4
2070F_4
2060F_4
2070F_4
2080F_4
2060F_4
2070F_4
2080F_4
2070F_4
2080F_4
2070F_4
2080F_4
2090F_4
2080F_4
2090F_4
2100F_4
69.99
82.37
105.0
125.0
127.7
159.4
156.9
187.5
231.5
239.6
286.1
296.3
343.3
363.2
358.7
449.4
443.8
436.4
543.0
542.7
523.5
641.4
638.7
785.9
772.8
783.1
927.2
945.2
999.9
5.69
4.79
3.80
3.16
5.58
2.50
4.54
3.53
3.08
5.17
2.49
4.24
2.08
3.46
5.03
2.80
4.06
5.06
2.32
3.30
3.98
2.81
4.14
2.29
2.86
5.36
2.25
4.44
5.88
2.85
2.40
1.90
1.58
2.79
1.25
2.27
1.77
1.54
2.59
1.25
2.12
1.04
1.73
2.52
1.40
2.03
2.53
1.16
1.65
1.99
1.41
2.07
1.15
1.43
2.68
1.13
2.22
2.94
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
3400
3400
3400
3400
5250
3400
5250
5250
5250
6500
5250
6500
5250
6500
8500
6500
8500
11000
6500
8500
11000
8500
11000
8500
11000
14000
11000
14000
17000
2.96
3.71
4.49
5.49
3.56
6.74
4.36
5.33
6.40
5.17
8.00
6.46
9.60
7.75
5.93
9.69
7.41
5.73
12.12
9.26
7.16
10.98
8.48
13.48
10.41
8.18
12.73
10.00
8.24
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
37.0
30.0
25.0
20.0
20.0
16.5
16.5
13.5
13.5
11.0
11.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
5.0
5.0
5.0
4.0
4.0
3.2
3.2
3.2
2.7
2.7
2.7
2.2
2.2
1.8
1.8
1.8
2040F_3
2040F_3
2040F_3
2040F_3
2050F_3
2040F_3
2050F_3
2040F_3
2050F_3
2050F_3
2060F_3
2050F_4
2060F_3
2050F_4
2060F_4
2070F_4
2060F_4
2070F_4
2060F_4
2070F_4
2080F_4
2070F_4
2080F_4
2070F_4
2080F_4
2090F_4
2080F_4
2090F_4
2100F_4
2090F_4
2100F_4
2090F_4
2100F_4
2110F_4
45.86
57.62
69.99
82.37
84.70
105.0
104.1
125.0
127.7
156.9
156.7
187.5
190.1
231.5
239.6
236.6
296.3
292.6
363.2
358.7
360.7
443.8
436.4
542.7
523.5
533.7
638.7
644.9
660.4
783.1
844.5
945.2
999.9
967.6
8.67
6.91
5.69
4.79
8.41
3.80
6.85
3.16
5.58
4.54
7.96
3.53
6.62
3.08
5.17
7.62
4.24
6.16
3.46
5.03
7.32
4.06
5.06
3.30
3.98
7.86
4.14
6.50
8.90
5.36
6.90
4.44
5.88
8.75
2.89
2.30
1.90
1.60
2.80
1.27
2.28
1.05
1.86
1.51
2.65
1.18
2.21
1.03
1.72
2.54
1.41
2.05
1.15
1.68
2.44
1.35
1.69
1.10
1.33
2.62
1.38
2.17
2.97
1.79
2.30
1.48
1.96
2.92
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
3400
3400
3400
3400
5250
3400
5250
3400
5250
5250
6500
5250
6500
5250
6500
8500
6500
8500
6500
8500
11000
8500
11000
8500
11000
14000
11000
14000
17000
14000
17000
14000
17000
18500
3.00
3.71
4.45
5.56
3.60
6.74
4.36
8.24
5.33
6.55
5.29
8.00
6.46
9.60
7.75
5.93
9.69
7.41
11.63
8.89
6.87
11.12
8.59
13.90
10.74
8.44
12.73
10.00
8.24
12.27
10.11
15.00
12.35
11.35
16 (311-110)
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
68.0
56.0
45.0
37.0
30.0
30.0
25.0
25.0
20.0
20.0
16.5
16.5
13.5
13.5
13.5
11.0
11.0
9.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
6.0
5.0
5.0
5.0
4.0
4.0
4.0
3.2
3.2
2.7
2.7
2.7
2.2
2.2
2.2
2.2
1.8
1.8
1.8
2040F_2
2040F_2
2040F_3
2040F_3
2040F_3
2050F_3
2040F_3
2050F_3
2050F_3
2060F_3
2050F_3
2060F_3
2050F_3
2060F_3
2070F_3
2060F_3
2070F_3
2060F_3
2070F_3
2080F_4
2060F_4
2070F_4
2080F_4
2070F_4
2080F_4
2090F_4
2070F_4
2080F_4
2090F_4
2080F_4
2090F_4
2100F_4
2090F_4
2100F_4
2090F_4
2100F_4
2110F_4
2090F_4
2100F_4
2110F_4
2120F_4
2100F_4
2110F_4
2120F_4
25.25
29.43
38.08
45.86
57.62
55.63
69.99
68.61
84.70
85.69
104.1
106.5
127.7
131.3
129.6
156.7
151.1
190.1
184.8
192.3
239.6
236.6
237.8
292.6
291.5
284.5
358.7
360.7
351.9
436.4
431.4
437.6
533.7
518.1
644.9
660.4
653.6
783.1
844.5
791.4
783.6
999.9
967.6
961.3
14.6
12.8
10.4
8.67
6.91
12.8
5.69
10.4
8.41
14.7
6.85
11.4
5.58
9.54
13.9
7.96
11.9
6.62
9.65
13.7
5.17
7.62
11.1
6.16
9.06
14.7
5.03
7.32
11.9
5.06
9.72
13.4
7.86
11.3
6.50
8.90
12.9
5.36
6.90
11.1
14.8
5.88
8.75
12.1
2.92
2.56
2.08
1.73
1.38
2.56
1.14
2.08
1.68
2.94
1.37
2.28
1.12
1.91
2.78
1.59
2.38
1.32
1.93
2.74
1.03
1.52
2.22
1.23
1.81
2.94
1.01
1.46
2.38
1.01
1.94
2.68
1.57
2.26
1.30
1.78
2.58
1.07
1.38
2.22
2.96
1.18
1.75
2.42
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
3400
3400
3400
3400
3400
5250
3400
5250
5250
6500
5250
6500
5250
6500
8500
6500
8500
6500
8500
11000
6500
8500
11000
8500
11000
14000
8500
11000
14000
11000
14000
17000
14000
17000
14000
17000
18500
14000
17000
18500
19000
17000
18500
19000
2.72
3.31
4.12
5.01
6.18
4.00
7.41
4.80
6.00
4.85
7.27
5.87
8.89
7.18
5.49
8.81
6.74
10.77
8.24
6.36
12.92
9.88
7.64
12.35
9.55
7.50
14.82
11.45
9.00
14.32
11.25
9.26
14.06
11.58
16.67
13.73
12.61
20.45
16.84
15.48
15.07
20.59
18.92
18.42
(311-110) 17
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
84.0
68.0
56.0
45.0
45.0
37.0
37.0
30.0
30.0
25.0
25.0
20.0
20.0
20.0
16.5
16.5
13.5
13.5
13.5
11.0
11.0
11.0
9.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
6.0
5.0
5.0
4.0
4.0
4.0
3.2
3.2
3.2
3.2
2.7
2.7
2.7
2.2
2.2
2.2
1.8
1.8
1.8
2040F_2
2040F_2
2040F_2
2040F_3
2050F_3
2040F_3
2050F_3
2050F_3
2060F_3
2050F_3
2060F_3
2050F_3
2060F_3
2070F_3
2060F_3
2070F_3
2060F_3
2070F_3
2080F_3
2060F_3
2070F_3
2080F_3
2070F_3
2080F_4
2090F_3
2070F_4
2080F_4
2090F_4
2080F_4
2090F_4
2100F_4
2090F_4
2100F_4
2090F_4
2100F_4
2110F_4
2090F_4
2100F_4
2110F_4
2120F_4
2100F_4
2110F_4
2120F_4
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
19.81
25.25
29.43
38.08
37.57
45.86
45.64
55.63
56.62
68.61
70.64
84.70
85.69
86.43
106.5
101.7
131.3
129.6
130.4
156.7
151.1
156.4
184.8
192.3
193.6
236.6
237.8
236.7
291.5
284.5
306.1
351.9
371.9
431.4
437.6
434.9
533.7
518.1
531.7
535.7
660.4
653.6
657.2
791.4
783.6
782.8
967.6
961.3
940.9
19.3
14.6
12.8
10.4
18.9
8.67
15.6
12.8
22.2
10.4
17.1
8.41
14.7
20.8
11.4
17.7
9.54
13.9
19.9
7.96
11.9
16.3
9.65
13.7
21.6
7.62
11.1
17.7
9.06
14.7
19.2
11.9
15.8
9.72
13.4
20.1
7.86
11.3
15.9
21.7
8.90
12.9
17.7
11.1
14.8
18.3
8.75
12.1
15.4
2.57
1.95
1.71
1.39
2.52
1.16
2.08
1.71
2.96
1.39
2.28
1.12
1.96
2.77
1.52
2.36
1.27
1.85
2.65
1.06
1.59
2.17
1.29
1.83
2.88
1.02
1.48
2.36
1.21
1.96
2.56
1.59
2.11
1.30
1.79
2.68
1.05
1.51
2.12
2.89
1.19
1.72
2.36
1.48
1.97
2.44
1.17
1.61
2.05
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
3400
3400
3400
3400
5250
3400
5250
5250
6500
5250
6500
5250
6500
8500
6500
8500
6500
8500
11000
6500
8500
11000
8500
11000
14000
8500
11000
14000
11000
14000
17000
14000
17000
14000
17000
18500
14000
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
3.31
4.09
4.96
6.18
4.00
7.51
4.86
6.00
4.85
7.20
5.82
9.00
7.27
5.56
8.81
6.74
10.77
8.24
6.36
13.22
10.11
7.81
12.35
9.55
7.50
14.82
11.45
9.00
14.32
11.25
9.26
13.50
11.12
16.88
13.90
12.77
21.09
17.37
15.96
15.54
20.59
18.92
18.42
23.22
22.61
19.09
28.38
27.63
23.33
18 (311-110)
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
420
380
125
100
84.0
68.0
68.0
56.0
56.0
45.0
45.0
37.0
37.0
30.0
30.0
25.0
25.0
25.0
20.0
20.0
16.5
16.5
16.5
13.5
13.5
11.0
11.0
11.0
9.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
5.0
5.0
5.0
4.0
4.0
4.0
3.2
3.2
3.2
2.7
2.7
2.7
2.2
2.2
2.2
1.8
1.8
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_3
2050F_3
2050F_3
2060F_3
2050F_3
2060F_3
2050F_3
2060F_3
2070F_3
2060F_3
2070F_3
2060F_3
2070F_3
2080F_3
2070F_3
2080F_3
2070F_3
2080F_3
2090F_3
2080F_4
2090F_3
2100F_4
2080F_4
2090F_4
2100F_4
2090F_4
2100F_4
2090F_4
2100F_4
2110F_4
2100F_4
2110F_4
2120F_4
2100F_4
2110F_4
2120F_4
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
2120F_4
2130F_4
4.120
4.655
13.86
16.83
19.81
25.25
25.27
29.43
30.16
38.08
37.57
45.64
46.65
55.63
56.62
68.61
70.64
71.14
85.69
86.43
106.5
101.7
107.7
129.6
130.4
151.1
156.4
157.5
192.3
193.6
202.3
237.8
236.7
243.7
284.5
306.1
351.9
371.9
352.3
437.6
434.9
445.7
518.1
531.7
535.7
653.6
657.2
643.3
791.4
783.6
782.8
961.3
940.9
28.5
28.5
28.1
23.3
19.3
14.6
28.0
12.8
23.5
10.4
18.9
15.6
26.9
12.8
22.2
10.4
17.1
25.3
14.7
20.8
11.4
17.7
23.8
13.9
19.9
11.9
16.3
26.6
13.7
21.6
28.9
11.1
17.7
24.1
14.7
19.2
11.9
15.8
24.8
13.4
20.1
26.0
11.3
15.9
21.7
12.9
17.7
25.9
11.1
14.8
18.3
12.1
15.4
2.85
2.85
2.81
2.33
1.93
1.46
2.80
1.28
2.35
1.04
1.89
1.56
2.69
1.28
2.22
1.04
1.71
2.53
1.47
2.08
1.14
1.77
2.38
1.39
1.99
1.19
1.63
2.66
1.37
2.16
2.89
1.11
1.77
2.41
1.47
1.92
1.19
1.58
2.48
1.34
2.01
2.60
1.13
1.59
2.17
1.29
1.77
2.59
1.11
1.48
1.83
1.21
1.54
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2530
2650
3030
3030
3400
3400
5250
3400
5250
3400
5250
5250
6500
5250
6500
5250
6500
8500
6500
8500
6500
8500
11000
8500
11000
8500
11000
14000
11000
14000
17000
11000
14000
17000
14000
17000
14000
17000
18500
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
19000
22500
1.19
1.25
3.33
4.16
4.41
5.45
3.53
6.62
4.29
8.24
5.33
6.49
5.24
8.00
6.46
9.60
7.75
5.93
9.69
7.41
11.75
8.98
6.94
10.98
8.48
13.48
10.41
8.18
12.73
10.00
8.24
15.27
12.00
9.88
15.00
12.35
18.00
14.82
13.62
18.53
17.03
16.58
23.16
21.28
20.72
25.23
24.56
20.74
30.96
30.14
25.45
36.84
31.11
(311-110) 19
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
640
575
520
470
420
380
230
190
155
125
100
100
84
84
68
56
56
45
45
37
37
37
30
30
30
25
25
25
20
20
16.5
16.5
16.5
13.5
13.5
13.5
11.0
11.0
11.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
6.0
5.0
5.0
5.0
4.0
4.0
4.0
3.2
3.2
3.2
2.7
2.7
2.2
1.8
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2050F_2
2050F_2
2050F_2
2060F_2
2050F_3
2060F_3
2050F_3
2060F_3
2070F_3
2060F_3
2070F_3
2080F_3
2060F_3
2070F_3
2080F_3
2070F_3
2080F_3
2070F_3
2080F_3
2090F_3
2080F_3
2090F_3
2100F_3
2080F_3
2090F_3
2100F_3
2090F_3
2100F_4
2090F_4
2100F_4
2110F_4
2100F_4
2110F_4
2120F_4
2100F_4
2110F_4
2120F_4
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
2120F_4
2130F_4
2130F_4
2130F_4
2.723
3.076
3.279
3.705
4.120
4.655
7.368
9.158
11.03
13.86
16.83
16.65
19.81
20.56
25.27
30.16
31.69
37.57
38.46
45.64
46.65
46.27
56.62
56.63
57.56
70.64
71.14
69.64
86.43
87.65
101.7
107.7
103.4
130.4
129.7
133.8
156.4
157.5
158.4
193.6
202.3
236.7
243.7
234.3
306.1
285.6
292.7
371.9
352.3
361.0
434.9
445.7
433.5
531.7
535.7
535.1
657.2
643.3
782.8
940.9
39.8
39.8
34.7
34.7
28.5
28.5
44.7
38.2
33.3
28.1
23.3
42.3
19.3
34.4
28.0
23.5
39.7
18.9
32.3
15.6
26.9
37.8
22.2
31.7
44.9
17.1
25.3
36.9
20.8
30.1
17.7
23.8
40.4
19.9
32.3
43.8
16.3
26.6
37.0
21.6
28.9
17.7
24.1
37.3
19.2
30.6
39.6
15.8
24.8
32.1
20.1
26.0
38.5
15.9
21.7
31.1
17.7
25.9
18.3
15.4
2.65
2.65
2.31
2.31
1.90
1.90
2.98
2.55
2.22
1.87
1.55
2.82
1.29
2.29
1.87
1.57
2.65
1.26
2.15
1.04
1.79
2.52
1.48
2.11
2.99
1.14
1.69
2.46
1.39
2.01
1.18
1.59
2.69
1.33
2.15
2.92
1.09
1.77
2.47
1.44
1.93
1.18
1.61
2.49
1.28
2.04
2.64
1.05
1.65
2.14
1.34
1.73
2.57
1.06
1.45
2.07
1.18
1.73
1.22
1.03
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2380
2380
2530
2530
2530
2650
2380
2670
2840
3030
3030
4370
3400
5120
5250
5250
6500
5250
6500
5250
6500
8500
6500
8500
11000
6500
8500
11000
8500
11000
8500
11000
14000
11000
14000
17000
11000
14000
17000
14000
17000
14000
17000
18500
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
19000
22500
22500
22500
1.24
1.38
1.44
1.59
1.78
1.88
3.45
3.73
4.29
4.99
6.24
4.32
6.62
4.39
5.29
6.43
5.19
8.00
6.46
9.73
7.86
6.01
9.69
7.41
5.73
11.63
8.89
6.87
11.12
8.59
13.48
10.41
8.18
12.73
10.00
8.24
15.62
12.27
10.11
15.00
12.35
18.00
14.82
13.62
18.53
17.03
16.58
22.24
20.43
19.89
25.54
24.87
21.00
31.93
31.09
26.25
36.84
31.11
38.18
46.67
20 (311-110)
11.0
11.0
11.0
9.0
9.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
6.0
5.0
5.0
5.0
4.0
4.0
4.0
3.2
3.2
2.7
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2050F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2070F_2
2060F_3
2070F_3
2060F_3
2070F_3
2080F_3
2060F_3
2070F_3
2080F_3
2070F_3
2080F_3
2090F_3
2070F_3
2080F_3
2090F_3
2080F_3
2090F_3
2100F_3
2080F_3
2090F_3
2100F_3
2090F_3
2100F_3
2110F_3
2090F_3
2100F_4
2110F_4
2120F_4
2100F_4
2110F_4
2120F_4
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
2120F_4
2130F_4
2130F_4
1.465
1.820
2.057
2.191
2.475
2.723
3.076
3.279
3.705
4.120
4.001
4.655
4.929
6.122
7.368
9.158
11.03
13.86
13.50
16.83
16.65
20.56
21.13
25.27
25.63
30.16
31.69
31.08
38.46
37.83
46.65
46.27
47.23
56.62
56.63
57.56
71.14
69.64
69.86
86.43
87.65
85.18
107.7
103.4
104.6
130.4
129.7
133.8
157.5
158.4
155.7
193.6
202.3
192.9
197.7
243.7
234.3
240.1
285.6
292.7
288.4
352.3
361.0
351.4
434.9
445.7
433.5
535.7
535.1
643.3
57.6
50.8
50.8
50.1
45.4
39.8
39.8
34.7
34.7
28.5
56.7
28.5
57.6
50.8
44.7
38.2
33.3
28.1
52.1
23.3
42.3
34.4
59.3
28.0
49.0
23.5
39.7
53.1
32.3
46.2
26.9
37.8
53.9
22.2
31.7
44.9
25.3
36.9
59.8
20.8
30.1
49.1
23.8
40.4
56.0
19.9
32.3
43.8
26.6
37.0
53.8
21.6
28.9
45.3
58.6
24.1
37.3
48.3
30.6
39.6
57.8
24.8
32.1
47.4
20.1
26.0
38.5
21.7
31.1
25.9
2.88
2.54
2.54
2.50
2.27
1.99
1.99
1.74
1.74
1.43
2.84
1.43
2.88
2.54
2.24
1.91
1.67
1.41
2.61
1.17
2.12
1.72
2.97
1.40
2.45
1.18
1.99
2.66
1.62
2.31
1.35
1.89
2.70
1.11
1.59
2.25
1.27
1.85
2.99
1.04
1.51
2.46
1.19
2.02
2.80
1.00
1.62
2.19
1.33
1.85
2.69
1.08
1.45
2.27
2.93
1.21
1.87
2.42
1.53
1.98
2.89
1.24
1.61
2.37
1.01
1.30
1.93
1.09
1.56
1.30
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2030
2040
2150
2200
2290
2380
2380
2530
2530
2530
2730
2650
2260
2280
2380
2670
2840
3030
4370
3030
4370
5120
6500
5250
6500
5250
6500
8500
6500
8500
6500
8500
11000
6500
8500
11000
8500
11000
14000
8500
11000
14000
11000
14000
17000
11000
14000
17000
14000
17000
18500
14000
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
18500
19000
22500
19000
22500
22500
1.06
1.30
1.36
1.47
1.57
1.65
1.84
1.92
2.12
2.37
2.20
2.50
3.19
3.95
4.60
4.97
5.72
6.65
4.61
8.32
5.77
5.86
4.62
7.06
5.70
8.57
6.92
5.29
8.62
6.59
10.48
8.01
6.19
12.92
9.88
7.64
11.86
9.16
7.20
14.82
11.45
9.00
13.88
10.91
8.98
16.97
13.33
10.98
16.36
13.48
12.38
20.00
16.47
15.14
14.74
19.76
18.16
17.68
22.70
22.11
18.67
27.24
26.53
22.40
34.05
33.16
28.00
41.45
35.00
41.48
(311-110) 21
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
1170
950
860
780
700
640
575
520
520
470
420
420
380
380
350
280
230
190
155
155
125
125
100
100
84
84
68
68
68
56
56
45
45
45
37
37
37
30
30
30
25
25
25
20
20
20
16.5
16.5
13.5
13.5
13.5
11.0
11.0
11.0
11.0
9.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
6.0
5.0
5.0
4.0
4.0
3.2
2.7
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2040F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2050F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_3
2070F_3
2080F_3
2060F_3
2070F_3
2080F_3
2070F_3
2080F_3
2090F_3
2070F_3
2080F_3
2090F_3
2080F_3
2090F_3
2100F_3
2090F_3
2100F_3
2090F_3
2100F_3
2110F_3
2090F_3
2100F_3
2110F_3
2120F_3
2100F_4
2110F_4
2120F_4
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
2120F_4
2130F_4
2120F_4
2130F_4
2130F_4
2130F_4
1.465
1.820
2.057
2.191
2.475
2.723
3.076
3.279
3.283
3.705
4.120
4.001
4.655
4.512
4.929
6.122
7.368
9.158
11.03
11.08
13.86
13.50
16.65
17.19
20.56
21.13
25.27
25.63
25.12
31.69
31.08
38.46
37.83
38.88
46.65
46.27
47.23
56.63
57.56
57.53
71.14
69.64
69.86
87.65
85.18
88.36
103.4
104.6
129.7
133.8
128.2
157.5
158.4
155.7
158.2
202.3
192.9
197.7
234.3
240.1
237.4
285.6
292.7
288.4
361.0
351.4
445.7
433.5
535.1
643.3
57.6
50.8
50.8
50.1
45.4
39.8
39.8
34.7
68.0
34.7
28.5
56.7
28.5
68.0
57.6
50.8
44.7
38.2
33.3
63.2
28.1
52.1
42.3
69.8
34.4
59.3
28.0
49.0
68.0
39.7
53.1
32.3
46.2
63.7
26.9
37.8
53.9
31.7
44.9
72.3
25.3
36.9
59.8
30.1
49.1
66.2
40.4
56.0
32.3
43.8
65.1
26.6
37.0
53.8
73.2
28.9
45.3
58.6
37.3
48.3
67.0
30.6
39.6
57.8
32.1
47.4
26.0
38.5
31.1
25.9
2.30
2.03
2.03
2.00
1.82
1.59
1.59
1.39
2.72
1.39
1.14
2.27
1.14
2.72
2.30
2.03
1.79
1.53
1.33
2.53
1.12
2.08
1.69
2.79
1.38
2.37
1.12
1.96
2.72
1.59
2.12
1.29
1.85
2.55
1.08
1.51
2.16
1.27
1.80
2.89
1.01
1.48
2.39
1.20
1.96
2.65
1.62
2.24
1.29
1.75
2.60
1.06
1.48
2.15
2.93
1.16
1.81
2.34
1.49
1.93
2.68
1.22
1.58
2.31
1.28
1.90
1.04
1.54
1.24
1.04
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2030
2040
2150
2200
2290
2380
2380
2530
2730
2530
2530
2730
2650
3140
2260
2280
2380
2670
2840
4020
3030
4370
4370
6500
5120
6500
5250
6500
8500
6500
8500
6500
8500
11000
6500
8500
11000
8500
11000
14000
8500
11000
14000
11000
14000
17000
14000
17000
14000
17000
18500
14000
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
19000
22500
19000
22500
22500
22500
1.33
1.63
1.70
1.84
1.97
2.07
2.30
2.39
2.22
2.65
2.96
2.75
3.13
2.64
3.98
4.93
5.75
6.21
7.16
5.06
8.32
5.77
7.21
4.85
7.32
5.77
8.82
7.13
5.45
8.65
6.62
10.77
8.24
6.36
13.10
10.02
7.74
12.35
9.55
7.50
14.82
11.45
9.00
14.32
11.25
9.26
13.64
11.23
16.67
13.73
12.61
20.45
16.84
15.48
15.07
20.59
18.92
18.42
22.70
22.11
18.67
28.38
27.63
23.33
33.16
28.00
41.45
35.00
43.75
51.85
22 (311-110)
100
84
84
84
68
68
56
56
56
45
45
45
37
37
37
30
30
30
25
25
25
20
20
20
16.5
16.5
16.5
13.5
13.5
13.5
13.5
11.0
11.0
11.0
9.0
9.0
9.0
7.5
7.5
7.5
6.0
6.0
6.0
5.0
5.0
4.0
3.2
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
2040F_2
2040F_2
2050F_2
2040F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2040F_2
2050F_2
2040F_2
2050F_2
2050F_2
2050F_2
2040F_2
2040F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2050F_2
2050F_2
2060F_2
2050F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2080F_2
2060F_3
2070F_3
2080F_3
2070F_3
2080F_3
2090F_3
2070F_3
2080F_3
2090F_3
2080F_3
2090F_3
2100F_3
2080F_3
2090F_3
2100F_3
2090F_3
2100F_3
2110F_3
2090F_3
2100F_3
2110F_3
2120F_3
2100F_3
2110F_3
2120F_3
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
2110F_4
2120F_4
2130F_4
2120F_4
2130F_4
2130F_4
2130F_4
1.465
1.820
1.822
2.057
2.191
2.475
2.723
2.702
3.076
3.279
3.283
3.705
3.714
4.001
4.512
4.929
6.122
7.368
7.598
9.158
9.119
11.03
11.08
13.50
16.65
17.19
20.56
21.13
20.54
25.63
25.12
31.69
31.08
31.15
38.46
37.83
38.88
46.27
47.23
48.23
56.63
57.56
57.53
69.64
69.86
71.64
87.65
85.18
88.36
103.4
104.6
104.9
129.7
133.8
128.2
128.9
158.4
155.7
158.2
192.9
197.7
199.0
234.3
240.1
237.4
285.6
292.7
288.4
361.0
351.4
433.5
535.1
57.6
50.8
87.5
50.8
50.1
45.4
39.8
79.2
39.8
34.7
68.0
34.7
79.2
56.7
68.0
57.6
50.8
44.7
87.0
38.2
76.5
33.3
63.2
52.1
42.3
69.8
34.4
59.3
84.8
49.0
68.0
39.7
53.1
77.7
32.3
46.2
63.7
37.8
53.9
86.3
31.7
44.9
72.3
36.9
59.8
81.6
30.1
49.1
66.2
40.4
56.0
82.5
32.3
43.8
65.1
89.7
37.0
53.8
73.2
45.3
58.6
81.0
37.3
48.3
67.0
30.6
39.6
57.8
32.1
47.4
38.5
31.1
1.92
1.69
2.92
1.69
1.67
1.51
1.33
2.64
1.33
1.16
2.27
1.16
2.64
1.89
2.27
1.92
1.69
1.49
2.90
1.27
2.55
1.11
2.11
1.74
1.41
2.33
1.15
1.98
2.83
1.63
2.27
1.32
1.77
2.59
1.08
1.54
2.12
1.26
1.80
2.88
1.06
1.50
2.41
1.23
1.99
2.72
1.00
1.64
2.21
1.35
1.87
2.75
1.08
1.46
2.17
2.99
1.23
1.79
2.44
1.51
1.95
2.70
1.24
1.61
2.23
1.02
1.32
1.93
1.07
1.58
1.28
1.04
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2030
2040
2450
2150
2200
2290
2380
2580
2380
2530
2730
2530
2730
2730
3140
2260
2280
2380
3300
2670
3700
2840
4020
4370
4370
6500
5120
6500
8500
6500
8500
6500
8500
11000
6500
8500
11000
8500
11000
14000
8500
11000
14000
11000
14000
17000
11000
14000
17000
14000
17000
18500
14000
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
18500
19000
22500
19000
22500
22500
22500
1.59
1.95
1.62
2.04
2.20
2.36
2.48
2.29
2.76
2.87
2.66
3.18
2.95
3.30
3.17
4.78
5.92
6.91
4.98
7.45
5.38
8.59
6.07
6.92
8.65
5.82
8.79
6.92
5.29
8.55
6.54
10.38
7.94
6.14
12.92
9.88
7.64
12.02
9.29
7.30
14.82
11.45
9.00
13.75
10.80
8.89
17.18
13.50
11.12
16.36
13.48
12.38
20.00
16.47
15.14
14.74
20.21
18.57
18.09
22.70
22.11
18.67
27.24
26.53
22.40
34.05
33.16
28.00
39.79
33.60
42.00
52.50
(311-110) 23
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
1170
1170
950
950
860
860
780
780
700
700
640
640
575
575
520
470
420
420
380
380
350
350
280
280
230
230
190
155
155
125
125
100
100
100
84
84
84
68
68
68
56
56
45
45
45
37
37
37
30
30
30
25
25
20
20
20
16.5
16.5
16.5
16.5
13.5
13.5
13.5
11.0
11.0
11.0
9.0
9.0
9.0
7.5
7.5
6.0
5.0
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2050F_2
2050F_2
2050F_2
2060F_2
2050F_2
2060F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2050F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2070F_2
2060F_2
2070F_2
2080F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2070F_3
2080F_3
2090F_3
2080F_3
2090F_3
2100F_3
2080F_3
2090F_3
2100F_3
2090F_3
2100F_3
2090F_3
2100F_3
2110F_3
2090F_3
2100F_3
2110F_3
2120F_3
2100F_3
2110F_3
2120F_3
2110F_3
2120F_3
2130F_3
2110F_4
2120F_4
2130F_4
2120F_4
2130F_4
2130F_4
2130F_4
1.465
1.476
1.820
1.822
2.057
2.028
2.191
2.252
2.475
2.504
2.723
2.702
3.076
3.095
3.283
3.714
4.001
4.130
4.512
4.567
4.929
4.980
6.122
6.147
7.368
7.598
9.119
11.08
11.26
13.50
13.72
16.65
17.19
17.33
21.13
20.54
20.98
25.63
25.12
25.17
31.08
31.15
37.83
38.88
39.51
47.23
48.23
48.39
57.56
57.53
57.29
69.86
71.64
85.18
88.36
86.02
103.4
104.6
104.9
107.0
133.8
128.2
128.9
155.7
158.2
154.8
192.9
197.7
199.0
240.1
237.4
288.4
351.4
57.6
115
50.8
87.5
50.8
115
50.1
90.3
45.4
102
39.8
79.2
39.8
90.3
68.0
79.2
56.7
114
68.0
114
57.6
114
50.8
100
44.7
87.0
76.5
63.2
110
52.1
90.7
42.3
69.8
102
59.3
84.8
117
49.0
68.0
96.7
53.1
77.7
46.2
63.7
98.7
53.9
86.3
119
44.9
72.3
102
59.8
81.6
49.1
66.2
101
40.4
56.0
82.5
108
43.8
65.1
89.7
53.8
73.2
93.6
45.3
58.6
81.0
48.3
67.0
57.8
47.4
1.44
2.88
1.27
2.19
1.27
2.88
1.25
2.26
1.14
2.55
1.00
1.98
1.00
2.26
1.70
1.98
1.42
2.85
1.70
2.85
1.44
2.85
1.27
2.50
1.12
2.18
1.91
1.58
2.75
1.30
2.27
1.06
1.75
2.55
1.48
2.12
2.93
1.23
1.70
2.42
1.33
1.94
1.16
1.59
2.47
1.35
2.16
2.98
1.12
1.81
2.55
1.50
2.04
1.23
1.66
2.53
1.01
1.40
2.06
2.70
1.10
1.63
2.24
1.35
1.83
2.34
1.13
1.47
2.03
1.21
1.68
1.45
1.19
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2030
2420
2040
2450
2150
2320
2200
2660
2290
2530
2380
2580
2380
2580
2730
2730
2730
5450
3140
5750
2260
3120
2280
3170
2380
3300
3700
4020
6500
4370
6500
4370
6500
8500
6500
8500
10200
6500
8500
11000
8500
11000
8500
11000
14000
11000
14000
17000
11000
14000
17000
14000
17000
14000
17000
18500
14000
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
19000
22500
22500
22500
2.12
1.78
2.60
2.17
2.73
2.53
2.94
2.43
3.14
2.85
3.31
3.05
3.68
3.40
3.55
3.93
4.40
2.20
4.22
2.31
6.37
4.62
7.89
5.68
9.21
6.64
7.17
8.09
5.00
9.23
6.20
11.53
7.75
5.93
9.23
7.06
5.88
11.40
8.72
6.74
10.59
8.18
13.18
10.18
8.00
12.38
9.73
8.01
15.27
12.00
9.88
14.40
11.86
18.00
14.82
13.62
21.82
17.97
16.51
16.08
21.96
20.18
19.65
24.77
24.11
20.36
30.27
29.47
24.89
35.37
29.87
37.33
44.80
24 (311-110)
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
1170
1170
950
950
860
860
780
780
780
700
700
640
640
575
575
520
520
470
470
420
420
380
380
350
280
280
230
230
190
190
155
155
125
125
125
100
100
100
84
84
84
68
68
56
56
56
45
45
45
37
37
37
30
30
30
25
25
25
20
20
20
16.5
16.5
16.5
13.5
13.5
13.5
11.0
11.0
11.0
9.0
9.0
7.5
6.0
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2040F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2070F_2
2060F_2
2070F_2
2080F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2070F_2
2080F_2
2090F_2
2080F_3
2090F_3
2100F_3
2080F_3
2090F_3
2100F_3
2090F_3
2100F_3
2110F_3
2090F_3
2100F_3
2110F_3
2100F_3
2110F_3
2120F_3
2100F_3
2110F_3
2120F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2120F_4
2130F_4
2130F_4
2130F_4
1.465
1.476
1.820
1.822
2.057
2.028
2.191
2.252
2.295
2.504
2.537
2.702
2.827
3.095
3.126
3.283
3.400
3.714
3.759
4.001
4.130
4.512
4.567
4.980
6.147
6.256
7.598
7.708
9.119
9.269
11.08
11.26
13.50
13.72
13.50
17.19
17.33
17.34
21.13
20.54
20.98
25.12
25.17
31.08
31.15
31.15
38.88
39.51
40.24
47.23
48.23
48.39
57.53
57.29
56.56
69.86
71.64
68.94
88.36
86.02
88.15
104.6
104.9
107.0
128.2
128.9
128.5
155.7
158.2
154.8
197.7
199.0
237.4
288.4
57.6
115
50.8
87.5
50.8
115
50.1
90.3
149
102
149
79.2
142
90.3
142
68.0
128
79.2
128
56.7
114
68.0
114
114
100
149
87.0
142
76.5
128
63.2
110
52.1
90.7
131
69.8
102
149
59.3
84.8
117
68.0
96.7
53.1
77.7
133
63.7
98.7
135
53.9
86.3
119
72.3
102
145
59.8
81.6
125
66.2
101
131
56.0
82.5
108
65.1
89.7
127
53.8
73.2
93.6
58.6
81.0
67.0
57.8
1.15
2.30
1.02
1.75
1.02
2.30
1.00
1.81
2.98
2.04
2.98
1.58
2.84
1.81
2.84
1.36
2.56
1.58
2.56
1.13
2.28
1.36
2.28
2.28
2.00
2.98
1.74
2.84
1.53
2.56
1.26
2.20
1.04
1.81
2.62
1.40
2.04
2.98
1.19
1.70
2.34
1.36
1.93
1.06
1.55
2.66
1.27
1.97
2.70
1.08
1.73
2.38
1.45
2.04
2.90
1.20
1.63
2.50
1.32
2.02
2.62
1.12
1.65
2.16
1.30
1.79
2.54
1.08
1.46
1.87
1.17
1.62
1.34
1.16
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2030
2420
2040
2450
2150
2320
2200
2660
4670
2530
4840
2580
5020
2580
5020
2730
5450
2730
5450
2730
5450
3140
5750
3120
3170
5240
3300
5770
3700
6140
4020
6500
4370
6500
8500
6500
8500
7480
6500
8500
10200
8500
11000
8500
11000
14000
11000
14000
17000
11000
14000
17000
14000
17000
18500
14000
17000
18500
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
19000
22500
22500
22500
2.65
2.23
3.25
2.71
3.41
3.16
3.67
3.04
1.73
3.56
1.86
3.82
1.96
4.25
2.18
4.44
2.22
4.91
2.46
5.49
2.75
5.28
2.88
5.77
7.10
4.29
8.30
4.75
8.96
5.40
10.11
6.25
11.53
7.75
5.93
9.69
7.41
8.42
11.54
8.82
7.35
10.90
8.42
13.24
10.23
8.04
12.73
10.00
8.24
15.48
12.16
10.02
15.00
12.35
11.35
18.00
14.82
13.62
18.53
17.03
16.58
22.46
20.64
20.10
25.23
24.56
20.74
30.96
30.14
25.45
36.84
31.11
37.33
46.67
(311-110) 25
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
1170
950
950
860
860
780
780
700
700
640
640
575
575
520
520
470
470
420
420
380
380
380
350
280
230
190
155
155
125
125
100
100
100
84
84
68
68
68
56
56
45
45
45
37
37
37
30
30
30
25
25
25
25
20
20
20
16.5
16.5
16.5
13.5
13.5
13.5
11.0
11.0
9.0
7.5
2050F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2050F_2
2060F_2
2060F_2
2070F_2
2050F_2
2060F_2
2070F_2
2060F_2
2060F_2
2060F_2
2060F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2070F_2
2080F_2
2090F_2
2080F_2
2090F_2
2080F_3
2090F_3
2100F_3
2090F_3
2100F_3
2110F_3
2090F_3
2100F_3
2110F_3
2090F_3
2100F_3
2110F_3
2120F_3
2100F_3
2110F_3
2120F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2120F_3
2130F_3
2130F_4
2130F_4
1.476
1.822
1.833
2.028
2.027
2.252
2.295
2.504
2.537
2.702
2.827
3.095
3.126
3.283
3.400
3.714
3.759
4.130
3.954
4.512
4.567
4.573
4.998
6.256
7.708
9.269
11.26
11.08
13.72
13.50
17.19
17.33
17.34
20.54
20.98
25.12
25.17
25.66
31.15
31.15
38.88
39.51
40.24
48.23
48.39
46.56
57.53
57.29
56.56
69.86
71.64
68.94
68.05
88.36
86.02
88.15
104.9
107.0
105.9
128.2
128.9
128.5
158.2
154.8
199.0
237.4
115
87.5
172
115
172
90.3
149
102
149
79.2
142
90.3
142
68.0
128
79.2
128
114
164
68.0
114
164
172
149
142
128
110
159
90.7
131
69.8
102
149
84.8
117
68.0
96.7
155
77.7
133
63.7
98.7
135
86.3
119
168
72.3
102
145
59.8
81.6
125
169
66.2
101
131
82.5
108
150
65.1
89.7
127
73.2
93.6
81.0
67.0
1.92
1.46
2.87
1.92
2.87
1.51
2.48
1.70
2.48
1.32
2.37
1.51
2.37
1.13
2.13
1.32
2.13
1.90
2.73
1.13
1.90
2.73
2.87
2.48
2.37
2.13
1.83
2.65
1.51
2.18
1.16
1.70
2.48
1.41
1.95
1.13
1.61
2.58
1.30
2.22
1.06
1.65
2.25
1.44
1.98
2.80
1.20
1.70
2.42
1.00
1.36
2.08
2.82
1.10
1.68
2.18
1.38
1.80
2.50
1.09
1.50
2.12
1.22
1.56
1.35
1.12
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
None
Shaft Fan
None
Shaft Fan
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
2420
2450
4420
2320
4580
2660
4670
2530
4840
2580
5020
2580
5020
2730
5450
2730
5450
5450
6280
3140
5750
6690
5110
5240
5770
6140
6500
8210
6500
8500
6500
8500
7480
8500
10200
8500
11000
14000
11000
14000
11000
14000
17000
14000
17000
18500
14000
17000
18500
14000
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
19000
22500
22500
22500
2.67
3.25
1.80
3.79
1.92
3.64
2.08
4.27
2.23
4.58
2.35
5.10
2.62
5.33
2.67
5.89
2.95
3.30
2.87
6.34
3.46
2.97
4.23
5.15
5.70
6.48
7.50
5.94
9.30
7.12
11.63
8.89
10.11
10.59
8.82
13.08
10.11
7.94
12.27
9.64
15.27
12.00
9.88
14.59
12.02
11.04
18.00
14.82
13.62
21.60
17.79
16.35
15.92
22.24
20.43
19.89
24.77
24.11
20.36
30.27
29.47
24.89
36.17
30.55
37.33
44.80
26 (311-110)
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
1170
950
860
780
700
640
575
520
520
470
470
420
420
380
380
350
280
230
190
190
155
155
125
125
125
100
100
84
84
84
68
68
56
56
56
45
45
45
37
37
37
30
30
30
25
25
25
20
20
20
16.5
16.5
16.5
13.5
13.5
11.0
9.0
2060F_2
2060F_2
2060F_2
2060F_2
2060F_2
2060F_2
2060F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2060F_2
2060F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2070F_2
2080F_2
2090F_2
2080F_2
2090F_2
2080F_2
2090F_2
2100F_2
2090F_3
2100F_3
2110F_3
2090F_3
2100F_3
2110F_3
2100F_3
2110F_3
2120F_3
2100F_3
2110F_3
2120F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2120F_3
2130F_3
2130F_3
2130F_4
1.548
1.833
2.027
2.295
2.537
2.827
3.126
3.400
3.211
3.759
3.713
4.130
3.954
4.567
4.573
4.998
6.256
7.708
9.269
8.996
11.26
11.08
13.72
13.50
13.67
17.33
17.34
20.54
20.98
21.01
25.17
25.66
31.15
31.15
31.21
39.51
40.24
38.38
48.23
48.39
46.56
57.29
56.56
57.02
71.64
68.94
68.05
86.02
88.15
81.72
104.9
107.0
105.9
128.9
128.5
154.8
199.0
190
172
172
149
149
142
142
128
193
128
193
114
164
114
164
172
149
142
128
193
110
159
90.7
131
189
102
149
84.8
117
188
96.7
155
77.7
133
183
98.7
135
196
86.3
119
168
102
145
202
81.6
125
169
101
131
200
82.5
108
150
89.7
127
93.6
81.0
Service
Factor
2.53
2.29
2.29
1.99
1.99
1.89
1.89
1.71
2.57
1.71
2.57
1.52
2.19
1.52
2.19
2.29
1.99
1.89
1.71
2.57
1.47
2.12
1.21
1.75
2.52
1.36
1.99
1.13
1.56
2.51
1.29
2.07
1.04
1.77
2.44
1.32
1.80
2.61
1.15
1.59
2.24
1.36
1.93
2.69
1.09
1.67
2.25
1.35
1.75
2.67
1.10
1.44
2.00
1.20
1.69
1.25
1.08
Minimum
Cooling
Required
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
None
Shaft Fan
None
Shaft Fan
Shaft Fan
None
Shaft Fan
None
Shaft Fan
None
Shaft Fan
None
Shaft Fan
None
Shaft Fan
Shaft Fan
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
4360
4420
4580
4670
4840
5020
5020
5450
6280
5450
6280
5450
6280
5750
6690
5110
5240
5770
6140
7570
6500
8210
6500
8500
7480
8500
7480
8500
10200
14000
11000
14000
11000
14000
17000
14000
17000
18500
14000
17000
18500
17000
18500
19000
17000
18500
19000
18500
19000
22500
18500
19000
22500
19000
22500
22500
22500
1.85
2.25
2.40
2.59
2.79
2.94
3.27
3.33
2.89
3.69
3.20
4.13
3.58
4.32
3.72
5.28
6.44
7.12
8.10
6.57
9.38
7.43
11.63
8.89
10.11
11.12
12.63
13.24
11.03
8.04
12.63
9.93
15.34
12.05
9.93
15.00
12.35
12.50
18.24
15.02
13.81
18.53
17.03
16.58
22.24
20.43
19.89
25.54
24.87
21.00
30.96
30.14
25.45
36.84
31.11
38.18
46.67
(311-110) 27
125
125
125
100
100
100
84
84
84
68
68
56
56
56
45
45
45
37
37
37
30
30
30
30
25
25
25
20
20
20
16.5
16.5
13.5
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
2060F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2080F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2090F_2
2070F_2
2080F_2
2090F_2
2080F_2
2090F_2
2100F_2
2090F_2
2100F_2
2090F_2
2100F_2
2110F_2
2100F_3
2110F_3
2120F_3
2100F_3
2110F_3
2120F_3
2100F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2120F_3
2130F_3
2130F_3
1.548
1.833
1.783
2.027
2.062
2.295
2.197
2.537
2.541
2.827
2.683
3.126
3.103
3.400
3.211
3.759
3.713
4.130
3.954
4.567
4.573
4.998
4.996
6.256
6.155
7.708
7.517
9.269
8.996
8.923
11.26
11.08
11.13
13.50
13.67
13.98
17.33
17.34
16.78
20.98
21.01
21.58
25.66
25.55
31.15
31.21
31.12
40.24
38.38
39.36
48.39
46.56
47.71
57.29
56.56
57.02
57.30
68.94
68.05
68.47
86.02
88.15
81.72
107.0
105.9
128.5
190
172
282
172
282
149
279
149
279
142
239
142
239
128
193
128
193
114
164
114
164
172
255
149
258
142
231
128
193
272
110
159
231
131
189
269
102
149
235
117
188
256
155
226
133
183
263
135
196
269
119
168
239
102
145
202
276
125
169
237
101
131
200
108
150
127
1.90
1.72
2.82
1.72
2.82
1.49
2.79
1.49
2.79
1.42
2.39
1.42
2.39
1.28
1.93
1.28
1.93
1.14
1.64
1.14
1.64
1.72
2.55
1.49
2.58
1.42
2.31
1.28
1.93
2.72
1.10
1.59
2.31
1.31
1.89
2.69
1.02
1.49
2.35
1.17
1.88
2.56
1.55
2.26
1.33
1.83
2.63
1.35
1.96
2.69
1.19
1.68
2.39
1.02
1.45
2.02
2.76
1.25
1.69
2.37
1.01
1.31
2.00
1.08
1.50
1.27
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
4360
4420
4810
4580
4870
4670
5120
4840
5190
5020
5590
5020
5590
5450
6280
5450
6280
5450
6280
5750
6690
5110
6060
5240
6190
5770
6670
6140
7570
5460
6500
8210
6350
8500
7480
11900
8500
8900
13800
10200
14000
15500
14000
16900
14000
17000
18100
17000
18500
19000
17000
18500
19000
17000
18500
19000
22500
18500
19000
22500
18500
19000
22500
19000
22500
22500
2.47
3.00
2.76
3.20
3.01
3.46
3.16
3.72
3.47
3.92
3.52
4.37
3.92
4.45
3.86
4.92
4.27
5.50
4.78
5.77
4.96
7.05
5.94
8.59
7.27
9.49
8.21
10.80
8.76
12.15
12.51
9.90
12.80
11.86
13.48
8.47
14.82
16.84
10.59
14.71
10.71
9.68
13.24
10.96
16.07
13.24
13.39
16.47
16.67
14.74
20.03
18.41
17.92
24.71
22.70
22.11
18.67
27.24
26.53
22.40
34.05
33.16
28.00
40.19
33.94
41.48
28 (311-110)
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
1170
950
950
860
860
780
780
700
700
640
640
575
575
520
520
470
470
420
380
380
350
350
350
280
280
280
230
230
230
190
190
190
155
155
155
125
125
125
125
100
100
100
84
84
68
68
68
56
56
56
56
45
45
45
45
37
37
37
30
30
30
25
25
25
20
20
16.5
13.5
2060F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2060F_2
2070F_2
2070F_2
2070F_2
2090F_2
2060F_2
2070F_2
2080F_2
2060F_2
2070F_2
2080F_2
2060F_2
2070F_2
2080F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2090F_2
2070F_2
2080F_2
2090F_2
2100F_2
2080F_2
2090F_2
2100F_2
2090F_2
2100F_2
2090F_2
2100F_2
2110F_2
2090F_2
2100F_2
2110F_2
2120F_2
2100F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2120F_3
2130F_3
2130F_3
2130F_3
1.548
1.833
1.783
2.027
2.062
2.295
2.197
2.537
2.541
2.827
2.683
3.126
3.103
3.400
3.211
3.759
3.713
3.954
4.573
4.763
4.998
4.996
5.161
6.256
6.155
6.290
7.708
7.517
7.638
9.269
8.996
8.923
11.08
11.13
11.51
13.50
13.67
13.98
14.01
17.34
16.78
17.29
21.01
21.58
25.66
25.55
25.39
31.15
31.21
31.12
31.89
40.24
38.38
39.36
39.60
46.56
47.71
47.26
56.56
57.02
57.30
68.94
68.05
68.47
88.15
81.72
105.9
128.5
190
172
282
172
282
149
279
149
279
142
239
142
239
128
193
128
193
164
164
330
172
255
370
149
258
362
142
231
324
128
193
272
159
231
312
131
189
269
359
149
235
309
188
256
155
226
307
133
183
263
353
135
196
269
332
168
239
322
145
202
276
125
169
237
131
200
150
127
1.52
1.38
2.26
1.38
2.26
1.19
2.23
1.19
2.23
1.14
1.91
1.14
1.91
1.02
1.54
1.02
1.54
1.31
1.31
2.64
1.38
2.04
2.96
1.19
2.06
2.90
1.14
1.85
2.59
1.02
1.54
2.18
1.27
1.85
2.50
1.05
1.51
2.15
2.87
1.19
1.88
2.47
1.50
2.05
1.24
1.81
2.46
1.06
1.46
2.10
2.82
1.08
1.57
2.15
2.66
1.34
1.91
2.58
1.16
1.62
2.21
1.00
1.35
1.90
1.05
1.60
1.20
1.02
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
None
Elec Fan
Shaft Fan
Shaft Fan
Elec Fan
Shaft Fan
Shaft Fan
Elec Fan
Shaft Fan
Shaft Fan
Elec Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Elec Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
None
Shaft Fan
Shaft Fan
None
None
Shaft Fan
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
4360
4420
4810
4580
4870
4670
5120
4840
5190
5020
5590
5020
5590
5450
6280
5450
6280
6280
6690
11500
5110
6060
4720
5240
6190
4370
5770
6670
4800
6140
7570
5460
8210
6350
11000
8500
7480
11900
13400
8900
11900
13400
14000
15500
14000
16900
16800
14000
17000
18100
19000
17000
18500
19000
22500
18500
19000
22500
18500
19000
22500
18500
19000
22500
19000
22500
22500
22500
3.09
3.75
3.45
4.00
3.76
4.32
3.94
4.65
4.34
4.90
4.40
5.46
4.90
5.56
4.82
6.15
5.34
5.97
6.20
3.60
8.81
7.43
9.53
10.73
9.09
12.87
11.87
10.27
13.30
13.50
10.95
15.18
12.38
16.00
9.24
14.82
16.84
10.59
9.40
21.06
13.24
11.75
13.39
12.10
16.54
13.71
15.97
20.09
16.54
16.74
14.80
20.59
20.83
18.42
15.56
23.01
22.40
18.92
28.38
27.63
23.33
34.05
33.16
28.00
41.45
35.00
43.75
53.85
(311-110) 29
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
1170
950
950
860
860
780
700
640
575
520
470
420
380
350
350
350
280
280
230
230
190
190
190
155
155
155
155
125
125
125
100
100
100
84
84
84
68
68
68
68
56
56
56
45
45
45
37
37
37
30
30
25
25
20
16.5
2060F_2
2060F_2
2070F_2
2060F_2
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2060F_2
2070F_2
2080F_2
2070F_2
2080F_2
2070F_2
2080F_2
2070F_2
2080F_2
2090F_2
2070F_2
2080F_2
2090F_2
2100F_2
2080F_2
2090F_2
2100F_2
2090F_2
2100F_2
2110F_2
2090F_2
2100F_2
2110F_2
2090F_2
2100F_2
2110F_2
2120F_2
2100F_2
2110F_2
2120F_2
2110F_3
2120F_3
2130F_3
2110F_3
2120F_3
2130F_3
2120F_3
2130F_3
2120F_3
2130F_3
2130F_3
2130F_3
1.548
1.833
1.783
2.027
2.062
2.197
2.541
2.683
3.103
3.211
3.713
3.954
4.573
4.998
4.996
5.161
6.155
6.290
7.517
7.638
8.996
8.923
9.257
11.08
11.13
11.51
11.58
13.67
13.98
14.01
16.78
17.29
17.01
21.01
21.58
20.76
25.66
25.55
25.39
25.91
31.21
31.12
31.89
38.38
39.36
39.60
46.56
47.71
47.26
57.02
57.30
68.05
68.47
81.72
105.9
190
172
282
172
282
279
279
239
239
193
193
164
164
172
255
370
258
362
231
324
193
272
386
159
231
312
411
189
269
359
235
309
433
188
256
401
155
226
307
439
183
263
353
196
269
332
168
239
322
202
276
169
237
200
150
1.27
1.15
1.88
1.15
1.88
1.86
1.86
1.59
1.59
1.29
1.29
1.09
1.09
1.15
1.70
2.47
1.72
2.41
1.54
2.16
1.29
1.81
2.57
1.06
1.54
2.08
2.74
1.26
1.79
2.39
1.57
2.06
2.89
1.25
1.71
2.67
1.03
1.51
2.05
2.93
1.22
1.75
2.35
1.31
1.79
2.21
1.12
1.59
2.15
1.35
1.84
1.13
1.58
1.33
1.00
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Electric Fan
Electric Fan
Shaft Fan
Electric Fan
Shaft Fan
Electric Fan
Shaft Fan
Electric Fan
Shaft Fan
Shaft Fan
Electric Fan
Shaft Fan
Shaft Fan
None
Electric Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
None
Shaft Fan
Shaft Fan
None
Shaft Fan
Shaft Fan
None
None
Shaft Fan
None
None
Shaft Fan
None
None
Shaft Fan
None
None
None
None
None
None
None
None
4360
4420
4810
4580
4870
5120
5190
5590
5590
6280
6280
6280
6690
5110
6060
4720
6190
4370
6670
5150
7570
5460
10300
8210
6350
11000
12600
7480
11900
13400
11900
13400
13300
14000
15500
12400
14000
16900
16800
17500
17000
18100
19000
18500
19000
22500
18500
19000
22500
19000
22500
19000
22500
22500
22500
3.71
4.50
4.14
4.80
4.51
4.73
5.20
5.28
5.88
5.79
6.40
7.17
7.43
10.57
8.91
11.44
10.90
15.45
12.32
15.96
13.14
18.22
9.66
14.85
19.20
11.09
9.68
20.21
12.71
11.28
15.88
14.10
20.86
16.07
14.52
18.15
19.85
16.45
19.17
15.88
19.85
20.09
17.76
25.00
22.11
18.67
27.61
26.88
22.70
33.16
28.00
39.79
33.60
42.00
50.91
30 (311-110)
DRIVE SIZE
&
Reduction
Exact
Ratio
HP
Rating
Service
Factor
Minimum
Cooling
Required
L.S. Shaft
OHL
Capacity
(lb)
Minimum
L.S. Shaft
Sprocket
Pitch Dia
950
860
780
700
640
575
350
350
350
280
280
280
230
230
230
190
190
190
155
155
155
125
125
125
100
100
100
84
84
84
68
68
68
68
56
56
56
45
45
37
37
30
30
25
20
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2070F_2
2080F_2
2090F_2
2070F_2
2080F_2
2090F_2
2070F_2
2080F_2
2090F_2
2080F_2
2090F_2
2100F_2
2080F_2
2090F_2
2100F_2
2090F_2
2100F_2
2110F_2
2090F_2
2100F_2
2110F_2
2100F_2
2110F_2
2120F_2
2100F_2
2110F_2
2120F_2
2130F_2
2110F_2
2120F_2
2130F_2
2120F_3
2130F_3
2120F_3
2130F_3
2120F_3
2130F_3
2130F_3
2130F_3
1.783
2.062
2.197
2.541
2.683
3.103
4.996
5.161
5.050
6.155
6.290
6.050
7.517
7.638
7.581
8.923
9.257
9.218
11.13
11.51
11.58
13.98
14.01
13.94
16.78
17.29
17.01
21.58
20.76
21.12
25.55
25.39
25.91
25.36
31.12
31.89
30.89
39.36
39.60
47.71
47.26
57.02
57.30
68.47
81.72
282
282
279
279
239
239
255
370
599
258
362
538
231
324
451
272
386
497
231
312
411
269
359
519
235
309
433
256
401
510
226
307
439
582
263
353
477
269
332
239
322
202
276
237
200
1.41
1.41
1.40
1.40
1.20
1.20
1.28
1.85
3.00
1.29
1.81
2.69
1.16
1.62
2.25
1.36
1.93
2.48
1.16
1.56
2.06
1.35
1.80
2.60
1.18
1.55
2.17
1.28
2.00
2.55
1.13
1.54
2.20
2.91
1.32
1.77
2.38
1.35
1.66
1.20
1.61
1.01
1.38
1.19
1.00
Electric Fan
Electric Fan
Electric Fan
Electric Fan
Electric Fan
Electric Fan
Electric Fan
Electric Fan
Shaft Fan
Electric Fan
Electric Fan
Shaft Fan
Electric Fan
Electric Fan
Shaft Fan
Electric Fan
Shaft Fan
Shaft Fan
Electric Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
None
Shaft Fan
Shaft Fan
None
None
Shaft Fan
None
None
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
Shaft Fan
4810
4870
5120
5190
5590
5590
6060
4720
8620
6190
4370
8870
6670
5150
8870
5460
10300
11900
6350
11000
12600
11900
13400
9060
11900
13400
13300
15500
12400
16100
16900
16800
17500
22500
18100
19000
22500
19000
22500
19000
22500
19000
22500
22500
22500
5.51
6.02
6.31
6.94
7.04
7.84
11.88
15.25
8.35
14.54
20.59
10.15
16.43
21.27
12.35
24.29
12.88
11.15
25.60
14.78
12.90
16.94
15.04
22.25
21.18
18.81
27.81
19.35
24.19
18.63
21.93
25.56
21.18
16.47
26.79
23.68
20.00
29.47
24.89
35.85
30.27
44.21
37.33
44.80
56.00
(311-110) 31
Reversing Service
Brake Equipped Applications
Oversized Prime Movers
Multi-Speed or Variable Speed Applications
Excessive Ambient Temperatures
Thermal Rating Application Factors
Excessive Overhung Loads or Thrust Loads
Product Modifications
Non-Standard Motors or Prime Movers
Non-Standard Motor Bracket Applications
Non-Horizontal Mounting Positions
How to Select By Horsepower
1. Determine Service Factor or Load Classification Factor See
Pages 8 & 9 or 10 & 11.
2. Calculate Equivalent Horsepower Multiply the actual
horsepower to be transmitted by the Service Factor.
3. Determine Drive Input Speed, Output Speed and Ratio.
4. Determine Drive Size Select the nearest standard ratio
from the Horsepower Rating Tables starting on Page 33.
Opposite the high speed shaft rpm, and the desired ratio and
output speed, trace right to a horsepower capacity equal to
or in excess of the equivalent horsepower calculated in Step
2. Read the drive size at the top of the column. When the
required input speed falls between two tabulated input speeds
of a drive with the same number of gear reductions,
interpolate to determine gear drive rating.
5. Select Drive Configuration Type FC or FZ. See Pages 58-61.
6. Check Thermal Horsepower Ratings See Page 42
for instructions.
7. Check Overhung Loads and Thrust Capacity See Pages
48-55 for instructions.
8. Check Gear Drive Dimensions Pages 58 thru 61.
9. Place the Order See Page 14 for How to Order.
Example
Application: Belt conveyor, uniformly fed, requires 13 hp at the
head shaft.
Duty Cycle: 10 hours per day.
Driver: 17 hp multi-cylinder engine, 1600 rpm, coupling
connected to drive.
Output: 115 rpm.
1. From Service Factor table, Page 9. . . motor driven, uniformly
fed, belt conveyor, 10 hour service requires 1.25 Service
Factor. From Table 2, Page 8, convert this service factor for
motor drive to 1.50 for engine drive.
2. Equivalent horsepower 1.50 x 13 = 19.5 hp.
3. Input Speed is 1600 rpm, output is 115 rpm, resulting in a
required ratio of 13.9:1.
32 (311-110)
Example
A drive to power a traveling water intake screen, 24 hours per day, is
to deliver 30,000 pound-inches output torque when output shaft
operates at 5 rpm. Source of power is a 3 hp, 1750 rpm motor.
1. From Service Factor table, Page 9. . .traveling water screen
requires 1.25 Service Factor for 24 hour service.
2. Equivalent Torque 1.25 x 30,000 = 37,500
pound-inches.
3. Input speed is 1750 rpm, output is 5 rpm, resulting in a
required ratio of 350:1.
4. Refer to the output Torque Capacity/Quadruple Reduction
Selection Table on Page 41. Closest standard ratio is 357.5. In
the 1750 high speed shaft section, opposite 357.5 ratio, trace
right to 45.2 (x 1000) (nearest torque exceeding equivalent
torque) and read drive size 2060 at top of column.
5. For this example we will assume that a Type FC horizontal
concentric shaft drive is desired.
6. Check thermal rating, Page 46. Convert torque to horsepower.
30,000 x 5
= 2.38 hp
63,000
The thermal rating is 18.6 for a size 2060F4 which exceeds the
application hp is satisfactory.
7. Refer to Page 48 to check overhung load capacity if a chain
drive is required on the low speed shaft.
8. Dimensions and weights for this drive are given on Page 60.
9. Place the order for the drive per instructions on Page 14.
HORSEPOWER t
TORQUE
Approx.
L.S.
Shaft
rpm
2040
2050
2060
2070
2080
2090
2040
2050
2060
2070
2080
2090
3500
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
2340
1900
1720
1560
1400
1280
1150
1040
940
840
760
700
560
460
380
310
250
200
168
136
112
93.5
82.5
82.5
81.3
73.7
64.7
64.7
56.4
56.4
48.0
48.0
93.5
82.5
72.7
62.0
54.0
45.7
39.7
35.3
23.8
20.8
187
142
187
147
166
129
147
114
129
98.2
114
186
163
141
126
110
96.5
82.7
68.1
49.9
42.8
308
280
280
243
243
231
231
209
209
185
185
280
243
231
209
185
160
131
111
97.0
77.4
...
459
459
454
454
412
412
375
375
325
322
415
419
381
337
302
256
199
166
129
102
645
602
602
588
588
526
526
443
443
434
434
602
588
526
443
394
338
272
225
184
148
973
880
973
763
880
666
763
603
666
516
603
973
874
732
627
506
437
382
305
253
224
2.47
2.70
3.05
3.21
3.28
3.17
3.58
3.33
3.76
3.56
4.02
8.29
9.09
9.64
10.2
10.7
11.4
12.0
12.6
10.8
11.0
4.97
4.66
6.83
5.96
7.48
6.27
8.19
6.74
8.62
7.07
9.26
16.7
18.0
19.3
20.7
21.9
23.5
24.8
25.2
22.7
23.2
8.58
9.24
10.2
10.0
11.1
11.8
13.0
12.8
14.1
13.8
15.2
25.2
27.4
32.1
34.9
37.5
39.5
40.5
42.2
44.7
44.1
14.7
17.0
18.0
20.8
19.9
23.0
21.7
25.1
23.1
26.5
37.3
46.4
51.6
54.6
60.2
62.2
62.1
61.4
58.3
57.1
18.1
20.4
22.3
24.3
26.5
26.4
28.8
26.0
28.3
31.8
34.6
55.9
66.6
72.3
71.2
78.9
83.2
84.9
85.0
83.4
83.0
26.3
28.5
36.6
31.0
39.7
33.0
43.1
37.2
45.9
38.7
51.7
88.4
95.2
99.9
104
105
110
115
115
117
126
2900
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
1900
1560
1400
1280
1150
1040
940
840
760
700
620
560
460
380
310
250
200
168
136
112
90
82.0
72.3
72.3
71.3
64.6
56.7
56.7
49.4
49.4
42.0
42.0
82.0
72.3
63.7
54.4
47.4
40.1
34.8
30.9
20.8
18.2
164
125
164
129
145
113
129
99.6
113
86.1
99.6
163
142
124
110
96.6
84.6
69.6
56.6
43.7
37.6
270
245
245
213
213
203
203
183
183
162
162
245
213
203
183
162
140
111
97.5
80.7
65.5
...
402
402
398
398
361
361
320
320
269
269
364
368
334
295
259
214
165
138
109
85.6
566
527
527
515
515
461
461
388
388
380
380
527
515
461
388
345
296
238
186
154
125
853
771
853
669
771
584
669
528
584
453
528
853
767
642
550
444
383
335
268
221
196
2.61
2.86
3.23
3.39
3.47
3.35
3.79
3.52
3.98
3.76
4.25
8.78
9.62
10.2
10.8
11.4
12.1
12.7
13.3
11.4
11.6
5.26
4.95
7.23
6.31
7.89
6.63
8.67
7.10
9.12
7.48
9.76
17.6
19.0
20.5
21.8
23.2
24.8
25.2
25.3
24.0
24.6
9.08
9.76
10.8
10.6
11.7
12.5
13.8
13.5
14.9
14.5
16.1
26.6
28.9
34.0
36.8
39.6
41.7
41.5
44.7
44.9
45.1
15.6
18.0
19.0
22.0
21.0
24.3
22.3
25.8
23.1
26.7
39.5
49.2
54.5
57.7
62.3
62.8
62.1
61.6
59.5
57.8
19.2
21.6
23.5
25.7
28.0
28.0
30.5
27.5
29.9
33.6
36.6
59.1
70.4
76.5
75.2
83.4
87.9
89.6
84.8
84.2
84.6
27.9
30.2
38.7
32.8
41.9
35.0
45.6
39.3
48.6
41.0
54.6
93.6
101
106
111
111
116
122
122
123
133
2400
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
1560
1280
1150
1040
940
840
760
700
620
560
510
460
380
310
250
200
168
136
112
90
74
71.8
63.3
63.3
62.4
56.6
49.7
49.7
43.3
43.3
36.8
36.8
71.8
63.3
55.8
47.6
41.5
35.1
30.5
26.1
18.2
16.0
144
109
144
113
127
98.8
113
87.2
98.8
75.4
87.2
143
125
109
96.5
84.7
71.0
57.8
47.0
38.3
32.2
236
215
215
186
186
178
178
160
160
142
142
215
186
178
160
142
123
93.4
81.0
67.0
54.3
...
352
352
349
349
316
316
265
265
223
223
319
322
293
259
216
178
138
116
91.5
71.7
496
462
462
451
451
404
404
340
340
319
319
462
451
404
340
303
257
198
157
130
105
747
676
747
586
676
511
586
452
511
385
452
747
671
562
481
389
336
294
234
194
172
2.76
3.02
3.42
3.59
3.68
3.55
4.01
3.73
4.21
3.98
4.50
9.29
10.2
10.8
11.4
12.0
12.8
13.5
13.6
12.1
12.4
5.58
5.21
7.67
6.68
8.35
7.01
9.18
7.51
9.63
7.92
10.3
18.7
20.2
21.7
23.1
24.6
25.2
25.3
25.4
25.4
25.5
9.59
10.3
11.4
11.2
12.4
13.2
14.6
14.3
15.8
15.4
17.0
28.2
30.5
36.0
38.9
42.0
44.3
42.2
44.9
45.1
45.2
16.5
19.1
20.1
23.3
22.3
25.7
22.3
25.8
23.1
26.8
41.8
52.0
57.8
61.2
62.8
63.1
62.8
62.5
60.3
58.5
20.3
22.9
24.9
27.2
29.6
29.6
32.2
29.1
31.7
34.1
37.1
62.6
74.5
81.0
79.6
88.5
92.2
90.1
86.5
85.9
85.9
29.5
32.0
41.0
34.7
44.4
37.0
48.3
40.7
51.4
42.1
56.5
99.0
107
112
117
118
123
129
129
131
141
High
Speed
Shaft
rpm
Nominal
Ratios
4%
DRIVE SIZE
DRIVE SIZE
t When selecting gear drives by hp method, check required hp (without service factor) against the application adjusted thermal hp ratings. For ratings at speeds higher than 3500
(311-110) 33
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
1750
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
1430
1170
DRIVE SIZE t
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
1170
950
860
780
700
640
575
520
470
420
380
350
280
230
190
155
125
100
84
68
56
57.6
50.8
50.8
50.1
45.4
39.8
39.8
34.7
34.7
28.5
28.5
57.6
50.8
44.7
38.2
33.3
28.1
23.3
19.3
14.6
12.8
115
87.5
115
90.3
102
79.2
90.3
68.0
79.2
56.7
68.0
114
100
87.0
76.5
63.2
52.1
42.3
34.4
28.0
23.5
190
172
172
149
149
142
142
128
128
114
114
172
149
142
128
110
90.7
69.8
59.3
49.0
39.7
282
282
279
279
239
239
193
193
164
164
255
258
231
193
159
131
102
84.8
68.0
53.1
397
370
370
362
362
324
324
272
272
233
233
370
362
324
272
231
189
149
117
96.7
77.7
599
542
599
470
542
410
470
330
410
281
330
599
538
451
386
312
269
235
188
155
133
762
647
568
497
411
359
309
256
226
183
750
627
519
433
401
307
263
869
753
629
510
439
353
1050
927
794
635
582
477
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
950
780
700
640
575
520
470
420
380
350
310
280
230
190
155
125
100
84
68
56
45
50.0
44.1
44.1
43.5
39.4
33.9
33.9
29.5
29.5
23.5
23.5
50.0
44.1
38.8
33.1
28.9
23.3
19.2
15.9
12.7
10.9
98.5
76.0
98.5
75.2
88.1
67.8
75.2
56.4
67.8
46.9
56.4
98.5
86.8
75.1
62.8
51.9
42.7
34.7
28.1
22.9
19.2
157
149
149
130
130
124
124
111
111
96.1
96.1
149
130
124
109
90.4
74.4
57.7
48.6
40.1
32.4
245
245
228
228
195
195
160
160
136
136
222
224
190
160
130
107
84.0
69.3
56.1
43.7
345
322
322
314
314
281
281
237
237
194
194
322
314
274
235
190
155
123
96.9
79.8
64.0
520
470
520
408
470
356
408
269
356
230
269
520
467
391
335
269
230
199
161
132
109
661
562
493
432
357
312
265
213
186
152
651
513
424
357
334
255
218
754
635
514
423
360
293
912
757
649
520
497
397
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
780
640
575
520
470
420
380
350
310
280
255
230
190
155
125
100
84
68
56
45
37
43.0
38.3
38.3
37.8
34.2
28.1
28.1
24.4
24.4
19.4
19.4
43.0
38.3
33.7
28.1
23.9
19.1
15.7
13.1
10.5
8.96
82.2
66.0
82.2
62.4
73.3
56.2
62.4
46.6
56.2
38.7
46.5
82.2
73.3
61.7
51.6
42.6
35.0
28.4
23.1
18.8
15.8
129
130
130
113
113
107
107
94.1
94.1
79.6
79.6
130
113
107
89.8
74.2
61.0
47.7
39.8
32.8
26.5
213
213
188
188
163
163
133
133
113
113
193
188
156
131
107
88.1
68.9
56.7
46.2
36.0
287
279
279
273
273
244
237
206
205
161
161
279
272
225
194
156
127
101
80.1
65.9
52.7
442
396
442
341
396
295
341
224
295
188
224
442
396
340
291
224
188
165
132
108
89.4
575
488
428
375
310
271
221
177
152
125
558
420
352
298
277
211
180
617
519
421
352
296
241
748
620
533
434
414
329
34 (311-110)
High
Speed
Shaft
rpm
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
1750
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
1430
1170
DRIVE SIZE
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
1170
950
860
780
700
640
575
520
470
420
380
350
280
230
190
155
125
100
84
68
56
3.04
3.33
3.76
3.95
4.05
3.90
4.41
4.10
4.63
4.23
4.78
10.2
11.2
11.9
12.6
13.2
14.0
14.1
13.8
13.3
13.6
6.11
5.74
8.40
7.32
9.19
7.71
10.1
8.04
10.6
8.17
11.0
20.4
22.1
23.8
25.1
25.2
25.3
25.4
25.5
25.5
25.5
10.6
11.4
12.6
12.3
13.6
14.5
16.0
15.7
17.3
17.0
18.7
31.0
33.6
39.4
42.7
44.6
44.8
43.2
45.1
45.2
45.3
18.1
20.9
22.1
25.5
23.1
26.7
22.3
25.8
23.3
27.0
45.9
57.2
62.5
62.5
63.4
63.7
63.6
62.7
61.5
59.4
22.3
25.1
27.4
30.0
32.6
32.6
35.5
31.9
34.8
34.1
37.2
68.7
82.0
89.1
87.4
92.5
93.0
93.0
88.4
87.6
87.1
32.4
35.2
45.1
38.2
48.8
40.7
53.1
40.7
56.5
42.1
56.6
109
117
123
129
129
135
142
142
143
149
139
149
156
165
171
181
192
199
208
206
256
259
260
265
300
281
295
361
380
393
388
409
405
448
481
490
486
531
531
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
950
780
700
640
575
520
470
420
380
350
310
280
230
190
155
125
100
84
68
56
45
3.23
3.54
4.00
4.20
4.30
4.07
4.59
4.26
4.82
4.27
4.82
10.9
11.9
12.6
13.4
14.0
14.2
14.2
13.9
14.1
14.1
6.40
6.10
8.80
7.46
9.72
8.07
10.3
8.16
11.1
8.27
11.2
21.6
23.5
25.1
25.2
25.3
25.4
25.5
25.5
25.5
25.5
10.7
12.0
13.3
13.1
14.5
15.4
17.1
16.6
18.4
17.5
19.3
32.8
35.8
42.1
44.5
44.8
45.0
43.7
45.2
45.3
45.2
19.2
22.3
22.1
25.5
23.1
26.7
22.6
26.2
23.7
27.4
48.9
60.7
62.9
63.4
63.4
63.6
64.1
62.7
62.1
59.8
23.7
26.8
29.1
31.8
34.6
34.6
37.6
34.1
37.1
34.8
37.9
73.2
87.0
92.2
92.4
93.1
93.4
94.0
89.6
88.5
87.8
34.4
37.3
47.9
40.6
51.8
43.2
56.4
40.6
60.1
42.2
56.5
116
124
131
137
136
142
147
149
149
150
148
159
166
175
182
193
202
202
209
209
271
259
260
268
306
285
299
383
392
393
394
411
412
476
481
490
487
555
540
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
780
640
575
520
470
420
380
350
310
280
255
230
190
155
125
100
84
68
56
45
37
3.39
3.75
4.24
4.46
4.56
4.12
4.65
4.31
4.87
4.30
4.86
11.4
12.6
13.4
13.9
14.2
14.3
14.2
14.0
14.3
14.2
6.53
6.47
8.98
7.57
9.88
8.18
10.4
8.24
11.2
8.34
11.3
22.0
24.3
25.2
25.3
25.4
25.4
25.5
25.6
25.6
25.7
10.8
12.8
14.2
14.0
15.4
16.3
18.0
17.2
19.0
17.7
19.6
35.0
38.1
44.4
44.8
45.0
45.1
44.2
45.3
45.3
45.2
20.5
23.7
22.2
25.7
23.6
27.2
23.0
26.6
24.1
27.8
51.9
62.3
63.1
63.5
63.8
64.0
64.3
62.7
62.5
60.2
24.1
28.3
30.9
33.8
36.8
36.7
38.8
36.2
39.2
35.3
38.4
77.5
92.1
92.5
93.2
93.5
93.5
94.3
90.5
89.3
88.4
35.8
38.4
49.7
41.4
53.4
43.8
57.6
41.3
60.8
42.2
57.5
120
129
139
145
139
142
149
149
149
150
157
169
176
186
193
204
206
206
209
210
284
259
264
273
310
288
302
384
391
394
400
413
414
477
482
492
497
565
547
(311-110) 35
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
870
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
720
580
DRIVE SIZE t
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
580
470
430
390
350
320
290
260
235
210
190
175
140
115
95
77
62
50
42
34
28
32.6
28.9
28.9
29.5
27.8
21.1
21.1
18.3
18.3
14.5
14.5
32.6
29.1
26.6
21.1
17.8
14.2
11.7
9.80
7.83
6.69
62.4
53.7
62.4
47.2
55.6
42.4
47.2
35.1
42.1
29.1
34.8
62.4
55.6
46.1
38.5
31.7
26.1
21.2
17.2
14.0
11.7
98.2
106
106
91.6
91.6
82.9
82.9
71.2
71.2
60.1
60.0
106
91.6
80.5
67.1
55.4
45.5
35.8
29.6
24.4
19.7
173
173
143
143
124
124
101
101
85.5
85.5
151
142
117
98.2
80.0
65.8
51.4
42.2
34.7
27.0
213
212
212
212
212
187
179
164
154
122
122
212
204
169
145
116
95.0
75.1
60.2
49.4
39.5
329
296
329
258
296
225
258
171
225
140
171
329
296
258
221
171
140
123
98.4
80.7
66.6
467
397
348
305
248
206
167
133
114
93.1
421
321
268
226
207
159
135
466
397
313
267
221
180
559
470
407
330
313
249
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
470
390
350
320
290
260
235
210
190
175
155
140
115
95
77
62
50
42
34
28
22
27.2
24.1
24.1
24.5
24.1
17.6
17.6
15.3
15.3
12.1
12.1
27.2
24.2
22.1
17.6
14.8
11.8
9.71
8.14
6.49
5.55
52.2
46.4
52.2
39.4
46.4
35.3
39.4
29.2
35.0
24.2
28.9
52.2
46.3
38.2
31.9
26.3
21.6
17.6
14.2
11.6
9.71
82.4
92.4
92.4
80.2
80.2
69.2
69.2
59.4
59.4
50.1
49.8
92.4
80.2
66.8
55.7
45.9
37.7
29.8
24.5
20.2
16.3
149
149
120
120
104
104
84.3
84.3
71.4
71.4
125
118
97.2
81.5
66.3
54.5
42.6
34.9
28.8
22.4
177
176
176
178
178
157
149
137
128
102
102
176
169
140
120
96.6
78.8
62.3
50.1
41.1
32.8
276
250
276
217
250
189
217
143
189
116
143
276
250
217
183
143
116
102
81.6
66.9
55.2
405
347
305
258
206
171
139
111
94.1
77.1
354
269
224
189
172
133
113
392
333
259
223
183
149
471
395
342
276
262
207
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
390
320
290
260
235
210
190
175
155
140
130
115
95
77
62
50
42
34
28
22
18
22.1
19.6
19.6
19.8
19.5
14.3
14.3
12.3
12.3
9.77
9.77
22.1
19.7
17.8
14.3
11.9
9.51
7.83
6.58
5.23
4.48
42.5
37.7
42.5
31.9
37.7
28.7
31.9
23.7
28.3
19.6
23.3
42.5
37.3
30.9
25.8
21.2
17.4
14.2
11.5
9.34
7.83
67.2
77.6
77.6
68.9
68.9
56.3
56.3
48.3
48.3
40.7
40.3
77.6
66.3
53.9
44.9
37.0
30.4
24.1
19.7
16.3
13.2
121
121
98.0
98.0
84.3
84.3
68.6
68.6
58.0
58.0
101
95.7
78.6
65.8
53.5
44.0
34.3
28.1
23.3
18.1
142
141
141
145
145
128
121
112
104
82.8
82.8
141
137
113
97.1
78.0
63.6
50.2
40.6
33.3
26.5
226
204
226
177
204
154
177
116
154
93.1
116
226
204
177
148
116
93.1
82.3
65.8
54.0
44.5
333
285
250
208
166
138
112
89.7
75.9
62.2
290
220
183
154
139
108
91.3
320
272
209
181
148
120
386
323
279
225
213
168
36 (311-110)
High
Speed
Shaft
rpm
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
870
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
720
580
DRIVE SIZE
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
580
470
430
390
350
320
290
260
235
210
190
175
140
115
95
77
62
50
42
34
28
3.46
3.81
4.30
4.68
4.98
4.16
4.70
4.35
4.91
4.33
4.89
11.6
12.9
14.2
14.0
14.2
14.2
14.3
14.1
14.3
14.3
6.67
7.08
9.16
7.70
10.1
8.30
10.6
8.34
11.3
8.43
11.4
22.5
24.8
25.4
25.4
25.4
25.5
25.6
25.6
25.6
25.6
11.0
14.1
15.6
15.2
16.8
17.0
18.8
17.5
19.4
18.0
19.8
38.4
41.5
44.9
45.0
45.2
45.2
44.6
45.3
45.3
45.2
22.3
25.8
22.8
26.3
24.1
27.9
23.5
27.2
24.5
28.3
54.6
63.3
63.7
64.0
64.2
64.3
64.5
62.8
63.1
60.8
24.1
29.0
31.5
35.3
38.4
37.8
39.4
38.7
39.6
35.9
39.1
79.2
92.9
93.5
93.7
93.5
94.1
94.3
91.4
90.0
89.1
35.8
38.6
49.8
42.2
53.7
44.9
58.6
42.4
62.4
42.2
59.0
120
130
142
148
143
142
149
150
150
150
172
184
193
204
208
209
209
208
211
210
289
266
271
278
311
292
304
390
403
394
408
415
416
480
491
505
508
575
557
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
470
390
350
320
290
260
235
210
190
175
155
140
115
95
77
62
50
42
34
28
22
3.49
3.84
4.34
4.70
5.22
4.19
4.74
4.39
4.96
4.36
4.93
11.7
13.0
14.2
14.1
14.3
14.3
14.3
14.1
14.3
14.3
6.74
7.40
9.26
7.76
10.2
8.35
10.7
8.39
11.4
8.47
11.4
22.7
24.9
25.4
25.5
25.5
25.5
25.6
25.5
25.7
25.6
11.2
14.8
16.4
16.1
17.8
17.1
18.9
17.7
19.5
18.1
19.9
40.4
43.9
45.1
45.2
45.2
45.3
44.8
45.3
45.3
45.2
23.3
26.9
23.1
26.7
24.4
28.2
23.7
27.4
24.7
28.6
54.6
63.5
63.9
64.2
64.3
64.4
64.6
62.7
63.3
60.9
24.2
29.1
31.6
35.8
39.0
38.4
39.6
39.1
39.8
36.3
39.5
79.5
93.0
93.6
93.7
94.0
94.3
94.5
92.0
90.5
89.4
36.3
39.4
50.5
42.9
54.8
45.6
59.6
42.9
63.3
42.3
59.6
122
132
144
148
144
142
150
150
150
150
180
195
204
208
209
210
210
210
210
211
293
270
273
281
313
295
308
396
408
394
412
415
416
489
498
513
513
581
560
1.50
1.84
2.03
2.25
2.49
2.76
3.05
3.38
3.74
4.13
4.57
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
390
320
290
260
235
210
190
175
155
140
130
115
95
77
62
50
42
34
28
22
18
3.52
3.88
4.38
4.71
5.24
4.23
4.78
4.38
4.95
4.37
4.94
11.8
13.1
14.2
14.2
14.3
14.3
14.3
14.2
14.3
14.3
6.81
7.46
9.36
7.80
10.3
8.42
10.7
8.45
11.4
8.52
11.4
23.0
24.9
25.5
25.6
25.5
25.5
25.7
25.7
25.6
25.7
11.3
15.5
17.1
17.2
19.0
17.3
19.1
17.8
19.7
18.3
20.0
42.1
45.1
45.1
45.2
45.3
45.3
45.0
45.2
45.4
45.4
23.4
27.1
23.4
27.0
24.6
28.4
23.9
27.7
24.9
28.8
54.8
64.0
64.2
64.3
64.4
64.5
64.6
62.7
63.6
61.1
24.1
28.9
31.5
36.2
39.4
38.8
40.0
39.7
40.1
36.6
39.8
79.0
93.6
93.7
94.1
94.3
94.5
94.5
92.5
91.0
89.7
36.9
39.9
51.3
43.4
55.5
46.1
60.3
43.2
64.1
42.1
60.0
124
134
146
149
145
141
150
150
150
151
183
199
207
208
209
210
210
210
211
211
298
274
277
285
314
298
309
401
414
394
415
417
416
497
506
520
519
587
564
(311-110) 37
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
1750
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
DRIVE SIZE t
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
45
37
30
25
20
16.5
13.5
11.0
9.0
10.4
8.67
6.91
5.69
4.79
3.80
3.16
2.50
...
18.9
15.6
12.8
10.4
8.41
6.85
5.58
4.54
...
32.3
26.9
22.2
17.1
14.7
11.4
9.54
7.96
6.62
46.2
37.8
31.7
25.3
20.8
17.7
13.9
11.9
9.65
63.7
53.9
44.9
36.9
30.1
23.8
19.9
16.3
...
98.7
86.3
72.3
59.8
49.1
40.4
32.3
26.6
21.6
135
119
102
81.6
66.2
56.0
43.8
37.0
...
196
168
145
125
101
82.5
65.1
53.8
...
269
239
202
169
131
108
89.7
73.2
...
332
322
276
237
200
150
127
93.6
...
1430
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
37
30
25
20
16.5
13.5
11.0
9.0
7.5
8.53
7.09
5.65
4.65
3.92
3.10
2.59
2.04
...
15.5
12.7
10.5
8.48
6.88
5.60
4.56
3.71
...
26.7
22.0
18.1
14.1
12.0
9.41
7.83
6.54
5.41
37.7
31.0
25.9
20.7
17.0
14.5
11.4
9.74
7.89
52.1
44.0
36.7
30.3
24.6
19.5
16.3
13.3
...
85.7
70.7
59.3
48.9
40.1
33.1
26.4
21.7
17.7
115
98.6
83.4
66.8
54.2
45.8
35.8
30.3
...
170
143
122
103
82.8
68.0
53.4
44.0
...
233
197
165
139
107
88.4
73.4
59.9
...
283
278
227
195
163
124
104
77.3
...
1170
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
30
25
20
16.5
13.5
11.0
9.0
7.5
6.0
6.99
5.80
4.62
3.81
3.21
2.54
2.12
1.67
...
12.7
10.4
8.56
6.94
5.63
4.58
3.74
3.04
...
21.9
18.0
14.8
11.6
9.81
7.73
6.40
5.36
4.42
30.9
25.5
21.2
16.9
13.9
11.8
9.29
7.97
6.47
42.6
36.0
30.0
24.9
20.1
15.9
13.4
10.9
...
70.6
57.9
48.6
40.0
32.9
27.1
21.6
17.8
14.5
96.1
80.8
68.3
54.7
44.3
37.5
29.3
24.8
...
143
119
101
84.5
67.8
55.7
43.8
36.1
...
196
162
135
114
87.8
72.4
60.1
49.0
...
231
230
189
160
134
103
85.0
63.8
...
870
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
22
18
15
12.5
10.0
8.3
6.8
5.5
4.5
5.20
4.32
3.44
2.83
2.39
1.89
1.58
1.24
9.42
7.76
6.37
5.17
4.19
3.41
2.78
2.26
16.3
13.4
11.0
8.71
7.29
5.78
4.76
3.99
23.0
19.0
15.8
12.6
10.4
8.81
6.91
5.93
31.7
26.8
22.3
18.5
15.0
11.8
9.95
8.14
52.6
43.1
36.2
29.8
24.4
20.1
16.1
13.2
72.3
60.2
50.8
40.7
33.0
27.9
21.8
18.4
109
90.0
76.4
62.9
50.5
41.4
32.6
26.9
146
120
101
84.6
65.3
53.8
44.7
36.5
172
172
142
119
99.4
76.7
63.2
47.9
...
...
3.29
4.81
...
10.8
...
...
...
...
720
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
18
15
12.5
10.0
8.3
6.8
5.5
4.5
3.8
4.31
3.58
2.85
2.34
1.98
1.56
1.31
1.03
...
7.80
6.43
5.27
4.28
3.47
2.82
2.30
1.87
...
13.5
11.1
9.14
7.24
6.04
4.80
3.94
3.30
2.72
19.0
15.8
13.1
10.4
8.58
7.29
5.72
4.91
3.99
26.2
22.2
18.5
15.4
12.4
9.79
8.24
6.74
...
43.5
35.7
29.9
24.7
20.2
16.7
13.3
11.0
8.91
59.9
49.8
42.1
33.7
27.3
23.1
18.1
15.3
...
91.1
75.2
63.5
52.1
41.8
34.3
27.0
22.3
...
121
99.7
83.5
70.0
54.1
44.6
37.0
30.2
...
142
142
117
98.2
82.2
63.5
52.3
39.8
...
580
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
15
12.5
10.0
8.3
6.8
5.5
4.5
3.8
3.0
3.47
2.88
2.29
1.89
1.60
1.26
1.05
0.83
...
6.29
5.18
4.25
3.45
2.79
2.27
1.85
1.51
...
10.8
8.93
7.36
5.85
4.86
3.88
3.17
2.66
2.19
15.3
12.7
10.5
8.39
6.91
5.87
4.61
3.96
3.21
21.1
17.9
14.9
12.4
9.98
7.89
6.64
5.43
...
35.1
28.8
24.1
19.9
16.3
13.4
10.7
8.83
7.18
48.3
40.2
33.9
27.2
22.0
18.6
14.6
12.3
...
74.2
61.1
51.2
42.0
33.7
27.6
21.8
18.0
...
97.4
80.4
67.3
56.4
43.6
35.9
29.8
24.3
...
115
115
94.5
79.1
66.3
51.1
42.1
32.2
...
38 (311-110)
High
Speed
Shaft
rpm
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
1750
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
DRIVE SIZE
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
45
37
30
25
20
16.5
13.5
11.0
9.0
14.3
14.3
14.3
14.3
14.2
14.4
14.2
14.3
...
25.6
25.6
25.6
25.7
25.6
25.7
25.6
25.7
...
44.7
45.2
45.2
43.5
45.3
43.7
45.1
44.9
45.3
62.9
63.0
64.6
64.8
64.7
64.8
64.9
64.7
64.2
89.2
91.6
93.0
92.5
95.0
92.3
93.4
91.8
...
140
150
150
150
151
150
151
151
151
196
207
210
210
211
211
211
211
...
271
282
295
310
313
311
300
302
...
381
411
415
414
416
416
416
417
...
473
548
569
584
588
572
587
522
...
1430
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
37
30
25
20
16.5
13.5
11.0
9.0
7.5
14.3
14.3
14.3
14.3
14.2
14.3
14.3
14.3
...
25.7
25.5
25.7
25.6
25.7
25.7
25.7
25.7
...
45.2
45.2
45.1
43.9
45.3
44.2
45.3
45.1
45.3
62.8
63.2
64.6
64.9
64.7
65.0
65.1
64.8
64.2
89.2
91.6
93.1
93.0
95.0
92.6
93.6
91.6
...
149
150
150
151
150
151
151
151
151
204
210
210
211
211
211
211
211
...
287
293
304
313
314
314
302
302
...
404
414
415
417
416
417
417
417
...
494
579
573
588
587
578
589
527
...
1170
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
30
25
20
16.5
13.5
11.0
9.0
7.5
6.0
14.3
14.3
14.3
14.4
14.2
14.4
14.3
14.3
...
25.7
25.6
25.6
25.6
25.7
25.7
25.7
25.7
...
45.4
45.2
45.1
44.1
45.3
44.3
45.2
45.2
45.2
62.9
63.5
64.6
64.7
64.7
64.6
64.8
64.8
64.4
89.2
91.6
93.0
93.4
94.9
92.2
94.1
91.8
...
150
150
151
150
151
151
151
151
151
208
211
211
211
211
211
211
212
...
296
298
308
314
314
314
302
303
...
415
416
415
418
417
417
417
417
...
493
585
583
590
590
587
588
532
...
870
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
22
18
15
12.5
10.0
8.3
6.8
5.5
4.5
14.3
14.3
14.4
14.3
14.3
14.4
14.3
14.3
25.6
25.6
25.7
25.7
25.7
25.7
25.7
25.7
45.4
45.3
45.1
44.6
45.2
44.6
45.3
45.3
63.0
63.7
64.8
64.9
65.1
64.9
64.9
64.9
89.2
91.7
93.0
93.3
95.2
92.1
93.9
92.2
150
151
151
151
151
151
151
151
211
211
211
211
211
211
211
211
303
303
313
314
315
314
303
303
416
415
417
417
417
417
417
418
493
589
589
590
588
588
588
537
...
...
45.3
64.4
...
151
...
...
...
...
720
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
18
15
12.5
10.0
8.3
6.8
5.5
4.5
3.8
14.4
14.4
14.4
14.3
14.3
14.3
14.3
14.4
...
25.6
25.7
25.7
25.7
25.7
25.7
25.7
25.7
...
45.4
45.3
45.3
44.8
45.3
44.8
45.3
45.2
45.2
62.9
64.0
64.9
64.7
64.9
64.9
64.9
64.9
64.5
89.1
91.7
93.2
93.8
95.1
92.3
94.0
92.2
...
150
151
151
151
151
151
151
152
151
211
211
211
211
211
211
212
212
...
306
306
314
314
315
315
303
304
...
417
416
417
417
417
418
417
418
...
492
587
587
588
588
588
588
539
...
580
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
15
12.5
10.0
8.3
6.8
5.5
4.5
3.8
3.0
14.4
14.3
14.3
14.4
14.3
14.4
14.3
14.4
...
25.7
25.7
25.7
25.7
25.7
25.7
25.7
25.7
...
45.1
45.3
45.3
44.9
45.2
44.9
45.2
45.3
45.2
62.9
63.8
64.6
64.8
64.9
64.8
64.9
65.0
64.4
89.1
91.8
93.2
93.8
95.0
92.3
94.0
92.2
...
151
151
151
151
151
151
151
151
151
211
211
211
212
211
211
212
212
...
309
309
315
314
315
314
304
304
...
416
417
417
417
417
417
417
418
...
495
590
588
588
588
588
588
542
...
(311-110) 39
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
1750
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
DRIVE SIZE t
2050
2060
2070
2080
2090
2100
2110
2120
2130
9.0
7.5
6.0
5.0
4.0
3.2
2.7
2.2
1.8
3.53
3.08
2.49
2.08
1.71
1.40
1.14
.920
.750
...
5.17
4.24
3.46
2.80
2.32
1.94
1.58
1.30
...
7.62
6.16
5.03
4.06
3.30
2.81
2.29
1.86
13.7
11.1
9.06
7.32
5.06
3.98
4.14
2.86
2.25
...
17.7
14.7
11.9
9.72
7.86
6.50
5.36
4.44
28.9
24.1
19.2
15.8
13.4
11.3
8.90
6.90
5.88
45.3
37.3
30.6
24.8
20.1
15.9
12.9
11.1
8.75
58.6
48.3
39.6
32.1
26.0
21.7
17.7
14.8
12.1
81.0
67.0
57.8
47.4
38.5
31.1
25.9
18.3
15.4
1430
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
7.5
6.0
5.0
4.0
3.2
2.7
2.2
1.8
1.5
2.89
2.52
2.04
1.70
1.40
1.15
.930
.750
.610
...
4.29
3.47
2.83
2.29
1.89
1.58
1.29
1.06
...
6.23
5.03
4.11
3.32
2.70
2.30
1.88
1.52
11.2
9.07
7.40
5.98
4.14
3.26
3.38
2.34
1.84
...
14.5
12.0
9.74
7.95
6.42
5.32
4.38
3.63
23.6
19.7
15.7
12.9
11.0
9.27
7.27
5.64
4.80
37.0
30.5
25.0
20.3
16.4
13.0
10.6
9.04
7.15
47.9
39.5
32.4
26.3
21.3
17.7
14.4
12.1
9.87
68.2
57.4
47.2
38.8
31.4
25.5
21.2
15.0
12.6
1170
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
6.0
5.0
4.0
3.2
2.7
2.2
1.8
1.5
1.2
2.36
2.06
1.67
1.39
1.14
.940
.760
.620
.500
...
3.51
2.84
2.31
1.87
1.55
1.29
1.06
.870
...
5.09
4.12
3.36
2.72
2.21
1.88
1.53
1.25
9.18
7.42
6.06
4.90
3.39
2.67
2.77
1.91
1.51
...
11.8
9.85
7.97
6.50
5.26
4.35
3.58
2.97
19.3
16.1
12.8
10.6
8.98
7.58
5.95
4.61
3.93
30.3
24.9
20.5
16.6
13.4
10.6
8.66
7.39
5.85
39.2
32.3
26.5
21.5
17.4
14.5
11.8
9.91
8.08
56.0
46.9
38.6
31.7
25.7
20.8
17.3
12.2
10.3
870
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
4.5
3.8
3.0
2.5
2.0
1.6
1.3
1.1
.90
1.76
1.53
1.24
1.03
.850
.700
.570
.460
.370
...
2.61
2.11
1.72
1.39
1.15
.960
.780
.650
...
3.79
3.06
2.50
2.02
1.64
1.40
1.14
.930
6.83
5.52
4.51
3.64
2.52
1.98
2.06
1.42
1.12
...
8.81
7.33
5.93
4.84
3.91
3.23
2.66
2.21
14.4
12.0
9.54
7.86
6.68
5.64
4.42
3.43
2.92
22.5
18.6
15.2
12.3
10.0
7.91
6.44
5.50
4.35
29.2
24.0
19.7
16.0
13.0
10.8
8.78
7.37
6.01
41.6
34.9
28.7
23.6
19.1
15.5
12.9
9.10
7.66
720
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
3.8
3.0
2.5
2.0
1.6
1.3
1.1
.90
.75
1.46
1.27
1.03
.860
.700
.580
.470
.380
.310
...
2.16
1.75
1.42
1.15
.950
.800
.650
.540
...
3.13
2.54
2.07
1.67
1.36
1.16
.940
.770
5.65
4.57
3.73
3.01
2.09
1.64
1.70
1.18
0.93
...
7.29
6.07
4.91
4.00
3.23
2.68
2.20
1.83
11.9
9.91
7.90
6.50
5.53
4.67
3.66
2.84
2.42
18.7
15.4
12.6
10.2
8.28
6.55
5.33
4.55
3.60
24.2
19.9
16.3
13.2
10.7
8.92
7.27
6.10
4.97
34.5
28.9
23.8
19.5
15.8
12.8
10.7
7.53
6.34
580
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
3.0
2.5
2.0
1.6
1.3
1.1
.90
.75
.60
1.17
1.02
.830
.690
.570
.470
.380
.310
.250
...
1.74
1.41
1.15
.930
.770
.640
.520
.430
...
2.52
2.04
1.67
1.35
1.09
.930
.760
.620
4.55
3.68
3.00
2.43
1.68
1.32
1.37
0.95
0.75
...
5.87
4.89
3.95
3.22
2.61
2.16
1.78
1.47
9.57
7.98
6.36
5.24
4.45
3.76
2.95
2.29
1.95
15.0
12.4
10.2
8.23
6.67
5.28
4.30
3.67
2.90
19.5
16.0
13.1
10.7
8.64
7.19
5.86
4.91
4.00
27.8
23.3
19.2
15.7
12.7
10.3
8.59
6.06
5.11
40 (311-110)
High
Speed
Shaft
rpm
Nominal
Ratios
4%
Approx.
L.S.
Shaft
rpm
1750
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
DRIVE SIZE
2050
2060
2070
2080
2090
2100
2110
2120
2130
9.0
7.5
6.0
5.0
4.0
3.2
2.7
2.2
1.8
23.8
25.7
25.6
25.7
25.7
25.6
25.7
25.7
25.7
...
44.6
45.2
45.2
45.3
45.4
45.4
45.3
45.2
...
64.9
64.9
64.9
64.9
64.5
64.9
64.8
64.4
94.8
95.0
95.1
95.0
79.5
75.0
95.2
79.6
75.1
...
151
151
151
151
151
151
151
151
210
211
212
212
211
211
212
210
212
315
315
315
315
315
304
304
316
305
417
418
417
417
417
418
419
417
419
580
573
600
600
601
599
600
516
522
1430
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
7.5
6.0
5.0
4.0
3.2
2.7
2.2
1.8
1.5
23.9
25.7
25.7
25.7
25.7
25.8
25.7
25.7
25.7
...
45.3
45.3
45.3
45.3
45.2
45.2
45.2
45.1
...
64.9
64.8
64.9
64.9
64.6
65.0
65.1
64.4
94.9
95.0
95.0
95.0
79.6
75.2
95.1
79.7
75.2
...
151
150
151
151
151
151
151
151
210
211
212
211
212
212
212
210
211
314
315
315
315
314
305
305
315
305
417
418
418
418
418
418
417
418
418
598
600
600
601
600
601
601
517
522
1170
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
6.0
5.0
4.0
3.2
2.7
2.2
1.8
1.5
1.2
23.8
25.7
25.7
25.7
25.6
25.7
25.7
25.7
25.7
...
45.3
45.3
45.2
45.3
45.3
45.1
45.4
45.3
...
64.8
64.9
64.9
65.0
64.6
64.9
64.7
64.7
95.0
95.0
95.1
95.2
79.7
75.3
95.3
79.5
75.4
...
150
151
151
151
151
151
151
151
210
211
211
212
212
211
212
210
212
315
314
315
315
314
303
305
315
305
417
418
418
418
418
418
418
418
418
600
599
599
600
600
599
599
514
522
870
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
4.5
3.8
3.0
2.5
2.0
1.6
1.3
1.1
.90
23.9
25.6
25.7
25.6
25.7
25.7
25.7
25.7
25.7
...
45.3
45.3
45.2
45.2
45.2
45.2
45.2
45.2
...
64.9
64.8
64.9
64.9
64.5
65.0
64.9
64.6
95.1
95.1
95.2
95.1
79.6
75.1
95.3
79.5
75.2
...
151
151
151
151
151
151
151
151
211
212
211
212
212
212
211
210
211
314
316
314
314
315
305
305
315
305
418
417
417
418
420
419
418
418
418
599
600
599
601
600
601
601
516
522
3.8
3.0
2.5
2.0
1.6
1.3
1.1
.90
.75
24.0
...
...
95.1
...
211
316
419
601
720
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
25.7
25.8
25.7
25.7
25.7
25.7
25.7
25.7
45.3
45.4
45.1
45.2
45.3
45.2
45.3
45.3
64.8
65.0
65.0
64.8
64.6
65.1
64.9
64.6
95.1
95.1
95.0
79.8
75.1
95.0
79.8
75.3
151
151
151
151
151
151
151
151
211
212
211
212
212
212
210
212
316
315
314
315
305
305
315
305
418
417
417
417
418
418
418
418
600
600
600
599
599
602
516
522
580
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
3.0
2.5
2.0
1.6
1.3
1.1
.90
.75
.60
23.8
25.6
25.7
25.7
25.7
25.7
25.7
25.7
25.7
...
45.3
45.4
45.4
45.2
45.2
45.3
45.3
45.3
...
64.8
64.8
65.1
65.1
64.3
64.9
65.0
64.6
95.0
95.1
95.0
95.2
79.6
75.1
95.1
79.7
75.2
...
151
151
151
151
151
151
151
151
210
211
211
212
212
212
212
210
212
314
316
316
315
315
305
305
315
305
419
417
416
420
418
418
418
418
418
601
601
601
599
598
599
600
515
522
(311-110) 41
Thermal Horsepower
42 (311-110)
Ambient
Temperature H
Factor with
Cooling Tubes
50F
60F
70F
80F
90F
100F
110F
120F
1.19
1.13
1.07
1.00
.93
.85
.78
.69
1.06
1.04
1.02
1.00
.98
.96
.94
.91
50F
60F
70F
80F
90F
100F
1.11
1.05
1.00
.94
.88
.83
0 to 2,500
2,500
5,000
7,500
10,000
12,500
15,000
1.00
.95
.90
.85
.81
.76
.72
100%
80%
60%
40%
20%
1.00
1.05
1.15
1.35
1.80
The duty cycle factor must be based on the percentage of each hour that the drive
is operating. For example: a gear drive operating for 48 minutes and resting for 12
minutes every hour of the day has an 80% duty cycle, but a drive operating for four
hours and resting for four hours has a 100% duty cycle. Where % run time per hour
falls between values shown above, use next higher % run time.
Installed
Environment
Factor Without
Shaft or Electric Fan
or Cooling Tubes
.75
1.00
1.40
Outdoors
1.90
The sustained ambient air velocity must be a continuous flow of air directly onto the
gear drive. If the air flow cannot be counted on to be continuous, an ambient air
velocity factor of 1.00 must be used.
(311-110) 43
1.50
thru
2.49
2.76
thru
4.57
Auxiliary
Cooling
3500
None
Shaft Fan
Electric Fan
Cooling Tubes
2900
None
Shaft Fan
Electric Fan
Cooling Tubes
2400
None
Shaft Fan
Electric Fan
Cooling Tubes
1750
DRIVE SIZE
2040
2050
2060
2070
2080
2090
None
Shaft Fan
Electric Fan
Cooling Tubes
60.5
...
...
...
65.5
...
...
...
79.3
153
245
580
92.1
178
288
651
118
237
361
740
176
560
664
1190
1430
None
Shaft Fan
Electric Fan
Cooling Tubes
64.3
...
...
...
72.5
...
...
...
84.8
146
243
539
100
170
286
610
127
224
358
696
196
523
676
1140
1170
None
Shaft Fan
Electric Fan
Cooling Tubes
67.0
...
...
...
77.8
...
...
...
88.4
138
239
497
104
161
281
566
131
211
351
648
212
485
677
1080
870
None
Shaft Fan
Electric Fan
Cooling Tubes
67.9
...
...
...
83.5
...
...
...
88.2
125
229
445
104
146
269
497
130
189
334
571
220
426
655
970
720
None
Shaft Fan
Electric Fan
Cooling Tubes
67.2
...
...
...
84.7
...
...
...
60.5
89.9
195
458
101
136
260
501
127
176
322
549
224
394
641
901
580
None
Shaft Fan
Electric Fan
Cooling Tubes
65.6
...
...
...
84.4
...
...
...
65.8
91.0
195
423
75.8
105
228
475
89.0
129
277
533
226
363
621
823
3500
None
Shaft Fan
Electric Fan
Cooling Tubes
2900
None
Shaft Fan
Electric Fan
Cooling Tubes
2400
None
Shaft Fan
Electric Fan
Cooling Tubes
1750
None
Shaft Fan
Electric Fan
Cooling Tubes
58.2
...
...
...
66.4
...
...
...
80.3
147
229
461
92.5
171
273
537
117
228
343
623
178
512
598
920
1430
None
Shaft Fan
Electric Fan
Cooling Tubes
59.0
...
...
...
71.6
...
...
...
83.4
138
225
420
97.5
162
269
494
123
214
338
574
194
467
593
860
1170
None
Shaft Fan
Electric Fan
Cooling Tubes
58.8
...
...
...
74.1
...
...
...
84.5
129
219
418
99.8
152
263
450
126
200
330
526
201
426
582
796
870
None
Shaft Fan
Electric Fan
Cooling Tubes
57.1
...
...
...
74.6
...
...
...
57.6
91.4
185
416
65.5
104
217
470
76.2
126
260
532
151
368
555
698
720
None
Shaft Fan
Electric Fan
Cooling Tubes
55.5
...
...
...
73.6
...
...
...
63.0
91.0
185
385
72.1
104
218
438
83.8
126
264
501
167
338
538
703
580
None
Shaft Fan
Electric Fan
Cooling Tubes
53.5
...
...
...
71.7
...
...
...
66.5
88.9
181
348
76.6
103
215
400
89.8
127
263
461
178
236
450
686
H Basic thermal ratings listed are for an ambient temperature of 80F (27C), from sea level to 2500 ft. Application adjusted thermal ratings must be calculated using the application
correction factors on Page 43 before comparing to the required load. For cooling beyond the range of cooling tubes, refer to Factory for the selection of oil-to-water or oil-to-air heat
exchangers. Thermal ratings with cooling tubes are based on a maximum water inlet temperature of 70F(21C) with a 2 gpm flow rate.
External cooling required for selections in shaded areas; refer to Factory.
44 (311-110)
5.06
thru
11.39
13.95
thru
31.39
DRIVE SIZE
High
Speed
Shaft
rpm
Auxiliary
Cooling
None
Shaft Fan
Electric Fan
Cooling Tubes
21.7
...
3500
...
...
...
...
...
...
None
Shaft Fan
Electric Fan
Cooling Tubes
34.1
19.7
2900
...
...
...
...
...
...
36.4
34.6
2400
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
40.4
50.0
1750
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
42.0
51.8
1430
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
42.5
54.6
1170
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
41.7
55.9
870
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
40.6
55.4
720
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
39.1
54.1
580
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
31.6
35.5
...
...
...
...
3500
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
...
...
...
...
33.2
39.0
...
...
...
...
2900
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
...
...
...
...
None
Shaft Fan
Electric Fan
Cooling Tubes
33.8
42.2
...
...
...
...
2400
...
...
...
...
...
...
...
...
...
...
None
Shaft Fan
Electric Fan
Cooling Tubes
33.4
44.3
1750
...
...
...
...
...
...
50.0
82.8
125
225
61.8
107
164
267
75.6
136
199
265
None
Shaft Fan
Electric Fan
Cooling Tubes
32.6
44.3
1430
...
...
...
...
...
...
33.3
61.0
107
231
38.3
73.4
136
284
None
Shaft Fan
Electric Fan
Cooling Tubes
31.6
43.5
1170
...
...
...
...
...
...
35.8
59.4
106
212
None
Shaft Fan
Electric Fan
Cooling Tubes
29.8
41.7
870
...
...
...
...
...
...
None
Shaft Fan
Electric Fan
Cooling Tubes
28.6
40.3
720
...
...
...
...
...
...
None
Shaft Fan
Electric Fan
Cooling Tubes
27.2
38.5
580
...
...
...
...
...
...
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
57.7
108
170
321
72.0
133
212
384
87.9
170
255
426
122
362
424
1010
151
507
600
1290
179
672
795
1520
211
914
1090
2410
205
967
1240
2290
61.1
102
167
291
75.9
126
210
351
92.3
159
251
390
132
332
423
928
166
467
603
1190
198
620
806
1420
242
854
1130
2280
253
912
1310
2860
62.4
95.7
162
268
77.4
119
205
318
93.8
149
245
355
141
303
415
845
179
428
596
1100
216
569
801
1320
268
790
1130
2130
281
859
1330
2690
61.9
86.4
154
282
77.6
108
195
316
93.3
134
233
347
145
265
398
726
190
374
575
953
235
498
777
1160
300
697
1110
1890
317
771
1320
2420
44.3
64.2
133
288
53.4
77.2
164
339
91.6
125
224
354
144
243
384
654
192
343
557
864
240
456
754
1060
314
641
1090
1740
338
715
1290
2240
46.9
63.5
131
261
57.0
76.9
163
310
65.6
92.5
191
340
141
220
367
731
189
311
534
790
240
413
725
948
320
582
1050
1560
352
653
1250
2020
61.5
281
324
538
65.3
403
467
707
175
543
628
855
213
763
884
1410
221
862
1060
1820
75.9
125
192
281
71.7
252
315
481
82.4
361
456
636
90.5
485
613
776
75.8
683
870
1280
253
777
1050
1670
42.5
73.3
137
263
48.3
90.3
162
293
81.6
226
304
521
94.9
323
441
673
107
434
595
699
112
612
848
1160
85.3
699
1020
1520
37.6
55.0
103
170
46.6
69.2
134
215
54.0
84.7
159
242
96.0
150
246
539
114
193
339
685
130
246
446
799
144
521
808
1130
146
596
977
1280
38.3
52.5
99.6
154
48.6
67.0
131
195
57.0
82.0
156
221
102
144
246
493
124
190
346
636
148
243
459
751
167
295
607
1200
166
542
943
1370
38.2
49.5
95.7
136
49.2
63.9
126
174
58.3
78.1
151
198
105
137
241
442
134
184
344
577
162
236
459
689
187
292
626
1120
191
299
718
1400
131
230
131
211
130
192
167
286
170
265
170
243
204
325
207
302
206
278
325
746
332
691
333
633
(311-110) 45
DRIVE SIZE
High
Speed
Shaft
rpm
Auxiliary
Cooling
2040
2050
2060
20.1
29.2
1750
None
Shaft Fan
Electric Fan
Cooling Tubes
...
...
...
...
...
...
31.8
...
79.1
163
1430
None
Shaft Fan
Electric Fan
Cooling Tubes
19.1
...
...
...
27.9
...
...
...
1170
None
Shaft Fan
Electric Fan
Cooling Tubes
18.1
...
...
...
870
None
Shaft Fan
Electric Fan
Cooling Tubes
720
2070
2080
2090
2100
2110
2120
2130
41.5
...
105
208
55.0
...
130
237
80.0
...
187
452
120
206
298
650
135
252
400
760
161
358
551
1160
176
409
680
1460
31.1
...
75.7
147
41.1
...
101
189
50.7
...
125
217
75.0
...
180
412
110
187
288
598
130
229
385
702
163
324
532
1080
184
372
658
1360
26.5
...
...
...
30.1
...
72.2
132
40.1
...
97.5
171
49.6
...
120
197
70.0
...
172
374
100
169
276
547
125
208
369
644
161
293
511
993
187
338
632
1260
16.7
...
...
...
24.6
...
...
...
28.5
...
67.1
112
38.2
...
90.8
146
47.3
...
112
169
63.4
...
160
321
94.6
147
258
474
120
181
344
562
157
254
477
872
183
294
590
1110
None
Shaft Fan
Electric Fan
Cooling Tubes
15.9
...
...
...
23.4
...
...
...
27.3
...
63.8
100
36.7
...
86.6
131
45.6
...
107
152
61.0
...
152
289
91.6
134
246
430
116
166
328
512
152
232
455
797
179
269
563
1020
580
None
Shaft Fan
Electric Fan
Cooling Tubes
14.9
...
...
...
22.1
...
...
...
25.9
...
60.2
88.1
35.0
...
81.8
116
43.4
...
101
134
58.1
...
144
255
87.6
122
233
382
111
151
310
457
146
209
431
715
172
244
532
918
1750
None
Shaft Fan
Electric Fan
Cooling Tubes
13.0
...
...
...
18.4
...
...
...
23.5
...
56.1
90.2
31.4
...
75.8
118
35.8
...
86.3
123
50.0
...
130
272
74.7
146
207
384
100
189
290
460
130
266
396
705
157
321
514
969
1430
None
Shaft Fan
Electric Fan
Cooling Tubes
12.3
...
...
...
17.5
...
...
...
22.6
...
53.3
79.9
30.3
...
72.1
105
34.6
...
82.2
110
48.6
...
123
244
72.6
131
198
346
97.1
169
276
415
126
236
377
639
153
286
490
884
1170
None
Shaft Fan
Electric Fan
Cooling Tubes
11.7
...
...
...
16.6
...
...
...
21.6
...
50.5
70.6
29.0
...
68.5
93.9
33.2
...
78.0
98.6
46.7
...
117
218
70.0
117
188
310
93.3
151
262
373
121
211
358
576
149
256
465
803
870
None
Shaft Fan
Electric Fan
Cooling Tubes
10.7
...
...
...
15.3
...
...
...
20.1
...
46.5
58.4
27.1
...
63.2
78.4
31.0
...
72.0
82.5
43.8
...
108
183
65.7
100
174
262
87.3
130
242
315
113
179
330
490
140
219
430
689
720
None
Shaft Fan
Electric Fan
Cooling Tubes
10.2
...
...
...
14.6
...
...
...
19.1
...
44.1
51.7
25.9
...
60.0
69.6
29.6
...
68.3
73.5
41.8
...
103
163
62.8
91.1
165
234
83.3
118
229
282
108
162
313
439
134
199
408
622
580
None
Shaft Fan
Electric Fan
Cooling Tubes
9.5
...
...
...
13.7
...
...
...
18.0
...
41.4
44.9
24.4
...
56.5
60.7
27.9
...
64.3
68.0
39.5
...
97.0
142
59.5
82.0
155
204
78.7
106
216
247
102
145
294
385
127
179
384
549
29.6
38.8
48.5
58.9
72.6
85.7
TRIPLE REDUCTION
38.44
thru
86.50
105.9
thru
194.6
QUADRUPLE REDUCTION
238.4
thru
985.3
580
thru
1750
None
...
16.1
18.6
23.5
46 (311-110)
Cooling Tubes
Cooling Tubes
(311-110) 47
Overhung Loads
High & Low Speed Shaft
CENTER LINE
OF LOAD
SEAL
CAGE
DISTANCE
Locate the center of the load as close to the drive seal cage as
practical to minimize the overhung load and increase bearing life.
Consult Factory for Higher Overhung Load Ratings In
many cases, overhung load capacity in excess of that published is
available. Published ratings are based on a combination of the
most unfavorable conditions of rotation, speed, direction of
applied load, and drive loading. If the actual load should exceed
the published capacity, refer full details to the Factory; provide
complete application information (see page 14), as well as
direction of rotation, location and direction of applied load.
48 (311-110)
DISTANCE
Inches
DRIVE SIZE
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
.85
.92
.96
1.00
1.13
1.20
1.26
1.33
1.39
1.53
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
.82
.88
.91
.94
1.00
1.06
1.11
1.17
1.23
1.34
1.45
1.51
1.57
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
.82
.87
.90
.92
.97
1.00
1.05
1.10
1.15
1.24
1.34
1.39
1.44
1.48
1.53
...
...
...
...
...
...
...
...
...
...
...
...
...
.79
.84
.86
.89
.93
.95
.98
1.00
1.04
1.13
1.22
1.26
1.30
1.34
1.39
1.43
1.47
1.56
...
...
...
...
...
...
...
...
...
...
.80
.84
.86
.88
.92
.94
.96
.98
1.00
1.08
1.16
1.20
1.24
1.28
1.32
1.36
1.40
1.48
1.56
...
...
...
...
...
...
...
...
...
.78
.82
.83
.85
.89
.91
.93
.94
.96
1.00
1.07
1.10
1.14
1.17
1.21
1.24
1.28
1.35
1.42
1.49
1.56
...
...
...
...
...
...
...
.77
.80
.82
.83
.87
.88
.90
.92
.93
.97
1.00
1.03
1.06
1.10
1.13
1.16
1.19
1.25
1.32
1.38
1.45
1.51
1.57
...
...
...
...
...
.75
.79
.80
.82
.85
.86
.88
.89
.91
.94
.97
.98
1.00
1.03
1.06
1.09
1.12
1.18
1.24
1.30
1.36
1.42
1.48
1.54
...
...
...
...
.76
.78
.80
.81
.84
.85
.86
.88
.89
.92
.95
.96
.97
.99
1.00
1.03
1.06
1.11
1.17
1.22
1.28
1.33
1.39
1.45
1.50
1.56
...
...
.74
.76
.77
.79
.81
.83
.84
.85
.87
.89
.92
.93
.95
.96
.97
.99
1.00
1.05
1.11
1.16
1.21
1.26
1.32
1.37
1.42
1.47
1.53
1.58
1
1
2
2
2
3
3
3
4
4
4
5
5
5
5
6
6
7
7
8
8
9
9
10
10
11
11
Q Interpolate for intermediate values. For example Lf is 1.12 for Size 2080 when the distance is 4 inches.
(311-110) 49
Approx.
L.S. Shaft
rpm
2040
2050
2060
2070
2080
2090
2340
1900
1720
1560
1400
1280
1150
1040
940
840
760
640
520
420
350
280
1.65
1.74
1.82
1.82
1.92
1.92
2.03
2.04
2.15
2.20
2.29
2.38
2.53
2.65
2.92
3.10
2.04
1.86
2.17
1.96
2.29
2.08
2.42
2.45
2.32
2.66
2.53
2.58
2.73
3.14
3.60
3.70
3.61
3.78
3.92
4.01
4.15
4.21
4.36
4.42
4.58
4.67
4.84
5.02
5.45
5.75
6.15
6.50
4.16
4.32
4.40
4.41
4.47
4.61
4.67
4.81
4.87
5.12
5.19
5.59
6.28
6.69
7.11
7.70
5.06
5.09
5.21
4.85
4.96
5.00
5.12
5.29
5.42
5.14
5.26
5.55
6.55
6.96
7.63
8.20
6.89
7.22
7.44
7.64
7.79
8.09
8.25
8.59
8.73
9.09
9.25
9.77
10.7
11.5
12.2
13.0
DRIVE SIZE
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
1.83
1.93
2.04
2.16
2.26
2.28
2.38
2.51
2.67
2.84
3.03
3.29
3.40
3.40
3.40
3.40
3.40
3.40
2.53
2.68
2.83
2.99
3.12
3.17
3.30
3.50
3.70
4.02
4.37
4.74
5.12
5.25
5.25
5.25
5.25
5.25
4.40
4.66
4.78
4.98
5.11
5.24
5.77
5.88
6.14
6.50
6.50
6.50
6.50
6.50
6.50
6.50
6.50
6.50
5.41
5.42
5.63
5.93
6.06
6.19
6.67
6.98
7.57
8.21
8.50
8.50
8.50
8.50
8.50
8.50
8.50
8.50
3.93
3.95
3.90
4.13
4.72
4.37
5.15
4.80
5.46
6.35
7.48
8.90
10.2
11.0
11.0
11.0
11.0
11.0
7.01
7.20
7.61
8.07
8.62
8.87
8.87
9.42
10.3
11.0
11.9
13.8
14.0
14.0
14.0
14.0
14.0
14.0
8.01
8.48
8.98
9.62
9.87
10.2
10.5
11.1
11.9
12.6
13.4
14.6
15.5
16.9
17.0
17.0
17.0
17.0
4.63
4.90
5.18
5.71
5.70
6.24
6.06
6.65
7.13
8.04
9.06
13.4
12.4
14.5
16.8
18.5
18.5
18.5
8.40
8.70
8.93
9.37
9.62
9.91
10.7
11.0
11.5
12.2
13.0
14.3
16.1
17.5
19.0
19.0
19.0
19.0
11.6
12.1
12.5
13.1
14.3
13.9
14.9
15.4
16.1
17.1
18.2
19.8
22.0
22.5
22.5
22.5
22.5
22.5
Published values of overhung load are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e.
pinion, sprocket, or sheave applications) an appropriate service factor should be considered in the overhung load calculation.
The last overhung load value in each drive size column applies to all lower output speeds for that drive. Published ratings are based on a combination of the most unfavorable
conditions of loading. For higher ratings, refer full data to Factory.
s
50 (311-110)
Double Reduction
Approx.
L.S.
Shaft
rpm
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
1170
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
230
190
155
125
100
84
68
56
45
37
10
0
30
50
100
190
350
400
110
160
250
220
440
500
300
410
490
500
500
500
0
0
10
290
540
600
600
600
600
600
570
660
800
800
800
800
800
800
800
800
10
20
620
440
1050
1050
1050
1050
1050
1050
220
290
380
550
1250
1250
1250
1250
1250
1250
1290
1400
1400
1400
1400
1400
1400
1400
1400
1400
1430
1500
1500
1500
1500
1500
1500
1300
1500
1500
1500
1500
1500
1370
1750
1750
1750
1390
1750
870
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
175
140
115
95
77
62
50
42
34
28
150
130
90
40
100
190
400
400
280
330
500
500
500
500
300
400
480
500
500
500
0
0
340
600
600
600
600
600
600
600
800
800
800
800
800
800
800
800
800
800
580
690
1050
1050
1050
1050
1050
1050
1050
1050
1070
1080
1040
1210
1250
1250
1250
1250
1250
1250
1400
1400
1400
1400
1400
1400
1400
1400
1400
1400
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1750
1750
1750
1750
1750
1750
720
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
140
115
95
77
62
50
42
34
28
22
240
230
200
30
90
180
400
400
390
400
500
500
500
500
290
400
480
500
500
500
0
0
580
600
600
600
600
600
600
600
800
800
800
800
800
800
800
800
800
800
1050
1050
1050
1050
1050
1050
1050
1050
1050
1050
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1400
1400
1400
1400
1400
1400
1400
1400
1400
1400
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1750
1750
1750
1750
1750
1750
580
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
115
95
77
62
50
42
34
28
22
18
350
340
330
20
90
180
400
400
400
400
500
500
500
500
290
400
480
500
500
500
110
190
600
600
600
600
600
600
600
600
800
800
800
800
800
800
800
800
800
800
1050
1050
1050
1050
1050
1050
1050
1050
1050
1050
1250
1250
1250
1250
1250
1250
1250
1250
1250
1250
1400
1400
1400
1400
1400
1400
1400
1400
1400
1400
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1750
1750
1750
1750
1750
1750
High
Speed
Shaft
rpm
Nominal
Ratios
WITHOUT BACKSTOP
H Published values of overhung load are for loads applied one shaft diameter from the seal cage with a service factor of unity. Where overhung load is proportional to torque (i.e.
pinion, sprocket, or sheave applications) an appropriate service factor should be considered in the overhung load calculation.
For input speeds higher than 1170 rpm, refer to Selection Guide 311-112.
For high speed shaft overhung load for Type FC drives with backstop, refer to Table on Page 54.
(311-110) 51
Triple Reduction
Approx.
L.S.
Shaft
rpm
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
1170
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
30
25
20
16.5
13.5
11.0
9.0
7.5
6.0
270
270
270
270
270
270
270
270
...
300
300
300
300
300
300
300
300
...
400
400
400
400
400
400
350
210
260
270
530
460
530
530
530
400
360
450
580
580
580
580
580
580
580
580
...
280
620
620
620
620
620
620
620
620
700
700
700
700
700
700
700
700
...
800
800
800
800
800
800
800
800
...
900
900
900
900
900
900
900
900
...
800
810
1000
1000
1000
1000
1000
1000
...
870
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
22
18
15
12.5
10.0
8.3
6.8
5.5
4.5
270
270
270
270
270
270
270
270
...
300
300
300
300
300
300
300
300
...
400
400
400
400
400
400
400
200
260
460
530
460
520
530
530
530
360
450
580
580
580
580
580
580
580
580
...
620
620
620
620
620
620
620
620
620
700
700
700
700
700
700
700
700
...
800
800
800
800
800
800
800
800
...
900
900
900
900
900
900
900
900
...
790
790
1000
1000
1000
1000
1000
1000
...
720
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
18
15
12.5
10.0
8.3
6.8
5.5
4.5
3.8
270
270
270
270
270
270
270
270
...
300
300
300
300
300
300
300
300
...
400
400
400
400
400
400
400
210
260
530
530
460
530
530
530
530
360
450
580
580
580
580
580
580
580
580
...
620
620
620
620
620
620
620
620
620
700
700
700
700
700
700
700
700
...
800
800
800
800
800
800
800
800
...
900
900
900
900
900
900
900
900
...
800
800
1000
1000
1000
1000
1000
1000
...
580
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
15.0
12.5
10.0
8.3
6.8
5.5
4.5
3.8
3.0
270
270
270
270
270
270
270
270
...
300
300
300
300
300
300
300
300
...
400
400
400
400
400
400
400
200
260
530
530
470
530
530
530
530
360
450
580
580
580
580
580
580
580
580
...
620
620
620
620
620
620
620
620
620
700
700
700
700
700
700
700
700
...
800
800
800
800
800
800
800
800
...
900
900
900
900
900
900
900
900
...
780
780
1000
1000
1000
1000
1000
1000
...
High
Speed
Shaft
rpm
Nominal
Ratios
WITHOUT BACKSTOP
52 (311-110)
Quadruple Reduction
Approx.
L.S.
Shaft
rpm
2050
2060
2070
2080
2090
2100
2110
2120
2130
1170
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
6.0
5.0
4.0
3.2
2.7
2.2
1.8
1.5
1.2
150
150
150
150
150
150
150
150
150
...
150
150
150
150
150
150
150
150
...
140
160
170
170
170
170
170
170
230
230
230
230
230
230
230
230
230
...
240
410
440
440
440
440
440
440
470
520
520
520
520
520
520
520
520
590
150
240
300
590
590
590
590
590
650
650
650
650
650
650
650
650
650
340
300
530
690
700
700
700
700
700
870
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
4.5
3.8
3.0
2.5
2.0
1.6
1.3
1.1
.90
150
150
150
150
150
150
150
150
150
...
150
150
150
150
150
150
150
150
...
140
160
170
170
170
170
170
170
230
230
230
230
230
230
230
230
230
...
240
410
440
440
440
440
440
440
470
520
520
520
520
520
520
520
520
590
150
240
300
590
590
590
590
590
650
650
650
650
650
650
650
650
650
700
650
590
700
700
700
700
700
700
720
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
3.8
3.0
2.5
2.0
1.6
1.3
1.1
.90
.75
150
150
150
150
150
150
150
150
150
...
150
150
150
150
150
150
150
150
...
140
160
170
170
170
170
170
170
230
230
230
230
230
230
230
230
230
...
240
410
440
440
440
440
440
440
470
520
520
520
520
520
520
520
520
590
150
240
300
590
590
590
590
590
650
650
650
650
650
650
650
650
650
700
700
590
700
700
700
700
700
700
580
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
3.0
2.5
2.0
1.6
1.3
1.1
.90
.75
.60
150
150
150
150
150
150
150
150
150
...
150
150
150
150
150
150
150
150
...
140
160
170
170
170
170
170
170
230
230
230
230
230
230
230
230
230
...
240
410
440
440
440
440
440
440
470
520
520
520
520
520
520
520
520
590
150
230
300
590
590
590
590
590
650
650
650
650
650
650
650
650
650
700
700
590
700
700
700
700
700
700
High
Speed
Shaft
rpm
Nominal
Ratios
WITHOUT BACKSTOP
(311-110) 53
Nominal
Ratios
Approx.
L.S.
Shaft
rpm
1170
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
230
190
155
125
100
84
68
56
45
37
870
5.06
6.20
7.59
9.30
11.39
720
5.06
6.20
7.59
9.30
11.39
DRIVE SIZE
2100
2110
2120
2130
560
630
630
630
630
630
630
630
630
630
710
710
710
710
710
710
710
650
720
720
720
720
720
680
870
870
870
700
870
175
140
115
95
77
615
630
630
630
630
710
710
720
870
140
115
95
77
62
630
630
630
630
630
710
710
720
870
115
95
77
62
50
630
630
630
630
630
710
710
720
870
580
5.06
6.20
7.59
9.30
11.39
1170
38.44
47.08
30
25
280
280
330
330
400
400
360
450
870
38.44
47.08
57.60
22
19
15
280
280
280
330
330
330
400
400
400
360
380
450
1170
194.6
238.4
291.9
357.5
437.9
6.0
5.0
4.0
3.2
2.7
230
60
95
120
230
260
260
260
260
260
240
210
240
280
280
H Published values of overhung load are for loads applied one shaft diameter from the backstop with a service factor of unity. Where overhung load is proportional to torque (i.e.
pinion, sprocket, or sheave applications) an appropriate service factor should be considered in the overhung load calculation. Refer to Factory for OHL ratings of drives with both
a fan and an external backstop.
For input speeds higher than 1170 rpm, refer to Selection Guide 311-112.
54 (311-110)
CONCENTRIC SHAFT
HORIZONTAL
OUTWARD
OUTWARD
INWARD
INWARD
TYPE FZ
TYPE FC
Approx.
L.S. Shaft
rpm
2040
2050
2060
2070
2340
1900
1720
1560
1400
1280
1150
1040
940
840
760
640
520
420
350
280
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
2.14
1.93
2.22
2.29
2.30
2.08
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
3.25
3.38
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.88
3.93
3.75
3.74
3.48
3.82
3.51
3.90
3.55
4.14
3.82
4.90
4.90
4.90
4.90
4.90
Approx.
L.S. Shaft
rpm
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
700
560
460
380
350
310
280
230
190
155
125
100
84
68
56
45
37
28
1.79
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
1.80
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
2.30
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
3.50
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
4.90
3.41
2.73
2.67
3.06
4.22
2.99
3.35
3.28
3.79
4.50
5.38
5.40
5.40
5.40
5.40
5.40
5.40
5.40
4.37
4.45
4.70
4.98
5.38
5.53
5.48
5.82
6.46
6.86
7.49
8.00
8.00
8.00
8.00
8.00
8.00
8.00
6.06
6.42
6.80
7.27
7.46
7.76
7.94
8.42
8.91
9.20
9.20
9.20
9.20
9.20
9.20
9.20
9.20
9.20
2.48
2.62
2.77
3.07
3.05
3.37
3.24
3.57
3.84
4.36
4.95
7.87
6.99
8.40
10.3
10.3
10.3
10.3
6.53
6.61
6.53
6.77
8.04
7.10
8.13
8.04
8.34
8.73
9.29
10.3
10.3
10.3
10.3
10.3
10.3
10.3
9.95
10.1
10.4
10.8
11.3
11.3
11.3
11.3
11.3
11.3
11.3
11.3
11.3
11.3
11.3
11.3
11.3
11.3
Q Thrust capacities are for pure thrust loads. If thrust and overhung loads are applied simultaneously, or loads exceed these capacities, refer to Factory.
The last thrust capacity value in each drive size column applies to all lower output speeds for that drive.
(311-110) 55
DRIVE SIZE
2040
1.465
1.820
2.057
2.191
2.475
2.723
3.076
3.279
3.705
4.120
4.655
4.929
6.122
7.368
9.158
11.03
13.86
16.83
19.81 Q
25.25
29.43 Q
2050
2060
2070
1.476
1.822
2.028
2.252
2.504
2.702
3.095
3.283
3.714
4.001
4.512
4.980
6.147
7.598
9.119
11.08
13.50
16.65
20.56
25.27
30.16
1.548
1.833
2.027
2.295
2.537
2.827
3.126
3.400
3.759
4.130
4.567
4.998
6.256
7.708
9.269
11.26
13.72
17.19
21.13
25.63
31.69
2050
2060
37.57
45.64
55.63
68.61
84.70
104.1
127.7
156.9
...
38.46
46.65
56.62
70.64
85.69
106.5
131.3
156.7
190.1
2080
1.783
2.062
2.197
2.541
2.683
3.103
3.211 Q
3.713
3.954 Q
4.573
4.996
6.155
7.517
8.996
11.08
13.50
17.33
20.54
25.12
31.08
2090
1.561Q
1.887
2.055
2.299
2.504
2.792
3.041
3.262
3.553 Q
4.067
4.430
5.161
6.290
7.638
8.923 Q
11.13
13.67
17.34
20.98
25.17
31.15
1.504
1.801
2.089
2.257
2.503
2.756
3.137
3.428
3.830
4.164
4.763 Q
5.050
6.050
7.581
9.257
11.51
13.98
16.78
21.01
25.66
31.15
2100
2110
2120
2130
5.071
6.417
7.641
9.218
11.58
14.01
17.29
21.58
25.55
31.21
9.463
11.46
13.94
17.01
20.76
25.39
31.12
11.54
14.00
17.37
21.12
25.91
31.89
11.85
14.42
17.15
21.25
25.36
30.89
Triple Reduction
Nominal
Ratios
38.44
47.08
57.66
70.62
86.50
105.9
129.7
158.9
194.6
DRIVE SIZE
2040
38.08
45.86
57.62
69.99
82.37 Q
105.0
125.0
159.4
...
2070
37.83
46.27
56.63
71.14
86.43
101.7
129.6
151.1
184.8 Q
2080
2090
38.88
47.23
57.56
69.64
87.65
107.7
130.4
156.4
...
39.51
48.23
57.53
69.86
85.18
103.4
129.7
157.5
193.6
2100
40.24 Q
48.39
57.29
71.64
88.36
104.6
133.8
158.4
2110
2120
38.38
46.56
56.56
68.94
86.02
104.9
128.2
155.7
39.36
47.71
57.02
68.05
88.15
107.0
128.9
158.2
2130
39.60
47.26
57.30
68.47
81.72 Q
105.9
128.5
154.8
Quadruple Reduction
Nominal
Ratios
194.6
238.4
291.9
357.5
437.9
536.3
656.8
804.5
985.3
DRIVE SIZE
2050
187.5
231.5
286.1
343.3
417.1
508.3 Q
627.0
774.1
951.5
2060
2070
...
239.6
296.3
363.2
449.4
543.0
649.5
795.9
965.5
...
236.6
292.6
358.7
443.8
542.7
641.4
785.9
961.2
2080
192.3
237.8
291.5
360.7
436.4
523.5
638.7
772.8
927.2 Q
2090
2100
2110
2120
2130
...
236.7
284.5
351.9
431.4
533.7
644.9
783.1
945.2
202.3
243.7
306.1
371.9
437.6
518.1
660.4
844.5
999.9
192.9
234.3
285.6
352.3
434.9
531.7
653.6
791.4
967.6
197.7
240.1
292.7
361.0
445.7
535.7
657.2
783.6
961.3
199.0
237.4
288.4
351.4
433.5
535.1
643.3
782.8
940.9
Q Except where noted with an (Q) asterisk, exact ratios are within 4% for double and triple reduction, and 5% of quadruple reduction nominal ratios.
56 (311-110)
C-Face Adapter
Motor Plate
Slide Base
...
...
...
OK
...
OK
...
...
...
...
OK
...
OK
...
...
...
...
OK
...
OK
...
...
...
...
...
OK
OK
OK
OK
OK
...
...
...
OK
Slide Rails
Motor Bracket
...
...
...
OK
...
...
OK
...
OK
OK
OK
OK
...
...
...
...
OK
...
OK
OK
OK
OK
OK
OK
OK
...
...
...
...
...
OK
...
...
OK
...
OK
OK
OK
OK
...
...
...
...
...
...
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
...
...
...
OK
OK
OK
OK
OK
...
OK
OK
...
...
...
OK
...
...
OK
OK
OK
OK
OK
OK
OK
OK
...
OK
...
OK
OK
OK
...
...
OK
OK
OK
OK
OK
...
OK
OK
OK
OK
OK
OK
...
...
OK
OK
OK
OK
OK
...
...
OK
...
OK
OK
OK
OK
OK
...
...
...
...
...
...
OK
OK
OK
OK
OK
OK
OK
OK
...
...
...
...
...
...
OK
OK
OK
OK
OK
OK
OK
OK
...
...
...
...
...
...
OK
OK
OK
OK
...
OK
OK
OK
...
...
...
...
...
...
OK
OK
OK
OK
OK
OK
OK
OK
...
...
...
...
...
...
...
...
...
OK
OK
OK
...
...
...
...
...
...
...
...
...
...
Internal Backstop
...
External Backstop
Motor Mount
Motor Bracket
C-Face Adapter
Motor Plate
Slide Base
Slide Rails
External Backstop
Internal Backstop
Shaft Fan
Electric Fan Right Hand
Electric Fan Left Hand
Cooling Tubes
Pump & Cooler
Ext. Backstop & Fan
Slide Rails
DRIVE SIZES
2060 thru 2130
Cooling Tubes
...
OK
OK
...
OK
Shaft Fan
...
OK
Slide Base
OK
Motor Plate
...
OK
C-Face Adapter
...
OK
Motor Bracket
...
OK
Motor Mount
Motor Mount
Motor Bracket
C-Face Adapter
Motor Plate
Slide Base
Slide Rails
Internal Backstop
Motor Mount
DRIVE SIZES
2040 & 2050
Internal Backstop
(311-110) 57
Type
FC
Dimensions Inches
H.S. SHAFT
KEY
Z
C
USABLE NA
LENGTH
X
CLEARANCE
USABLE
LENGTH
L.S. SHAFT
KEY
1.4
UA
O
D
V
Q
V
F
DRIVE
SIZE
OIL DRAIN
BOTH ENDS
J
E
E
A
2040 15.00
2050 16.60
7.90
8.98
8.50
9.60
6.60
7.30
6.10
7.10
.80
1.00
.750
.875
4.3
4.5
4.00
5.00
12.92
14.52
6.86
8.10
5.9
6.7
DRIVE
SIZE
H
NA
2040
2050
18.44
21.54
2.76
3.26
Wl
V
Key
2.0000
2.5000
.90
.94
3.54
4.16
Key
1.3750
1.6250
NA
18.44
21.54
2.76
3.26
Max
AA
Wt-lb
Ave
7.50
8.70
2.90
3.40
2.06
2.90
17.98
18.98
200
340
W/O With
3.24
3.92
Key
1.3750
1.6250
NA
19.98
2.00
Key
1.0000
H Dimensions are for reference only and are subject to change without notice unless certified. Drives are for horizontal floor mounted operation unless specifically stated otherwise.
58 (311-110)
DIMENSIONS ON PAGE 58
(CA IN TABLE BELOW)
AA
CA
SHAFT
GAP
C
GUARD
X
CLEARANCE
USABLE
LENGTH
L.S. SHAFT
KEY
1.4
U
O
D
V
Q
V
F
Average
Weight
of Drive
Only
lb n
Max. t
NEMA
T&U
Frame
Size
DRIVE
SIZE
OIL DRAIN
BOTH ENDS
J
E
E
A
145T
182T
184T
213T
215T
254T
256T
284TS
286TS
324TS
326TS
36.2
39.0
39.9
42.4
41.5
44.2
43.9
46.2
43.9
46.2
48.8
48.8
39.0
41.6
45.2
47.8
45.2
47.8
46.3
48.9
46.3
48.9
52.9
52.9
OPEN MOTORS
2040
2050
200
340
286
326
33.9
36.2
33.9
36.2
33.9
36.2
33.9
36.2
35.0
37.5
TEFC MOTORS
2040
2050
200
340
286
326
30.7
33.7
31.2
34.2
33.2
36.3
34.2
37.3
39.0
41.6
10
15
20
25
30
40
50
60
75
100
125
150
200
FRAME t
143T
145T
145T
182T
184T
213T
215T
254T
256T
284T
286T
324T
326T
364T
365T
404T
405T
444T
445T
100
115
120
110
120
130
110
120
135
165
165
310
180
180
310
270
270
375
270
285
375
340
445
485
DRIVE SIZE
2040-2070
2080-2090
2100-2130
60
65
70
60
65
70
60
65
85
60
75
85
65
80
90
65
80
90
80
95
110
80
100
110
100
115
120
30
35
40
60
80
120
165
230
265
360
380
490
526
650
780
1050
1505
1530
1700
TEFC High
Efficiency Motor
30
45
55
70
85
125
170
235
300
450
440
560
650
785
870
1150
1520
1710
1850
OPEN
MOTOR
30
35
35
60
70
120
145
190
215
255
315
370
400
575
640
810
895
1195
1375
(311-110) 59
Z
Y
NA
USABLE
LENGTH
VENTED
DIPSTICK
LIFTING LUGS:
SIZES 2100 THRU 2130
OIL FILLER PLUG
C
USABLE
LENGTH
NA
X
CLEARANCE
USABLE
LENGTH
2.6
R
R
1.3
UA
O
D
OIL DRAIN
BOTH ENDS
G
W
V
E
A
DRIVE
SIZE
H
2060
2070
2080
2090
2100
2110
2120
2130
18.40 n
12.00
13.70
15.80
17.50
19.16
21.48
23.60
25.10
10.60
11.66
12.78
15.74
17.40
19.50
21.90
24.70
8.20
9.30
10.20
11.40
12.20
13.10
14.44
15.20
10.00
11.30
13.20
14.30
14.96
17.28
18.80
19.30
.66
.66
.78
.90
1.00
1.00
1.24
1.24
1.000
1.125
1.250
1.500
1.500
1.500
1.750
1.750
4.2
4.5
5.5
7.0
9.0
9.0
9.0
9.0
7.0
7.0
7.0
7.0
5.50
6.50
7.00
8.00
9.00
9.50
10.00
11.00
15.60
17.16
18.98
23.06
26.00
28.80
32.50
36.20
8.00
9.20
10.00
11.50
13.14
13.72
14.58
16.16
6.9
7.9
8.7
9.6
10.7
11.6
12.6
13.5
21.00 n
23.00 n
26.00
27.60 n
29.40
32.48
34.00
Key
2.750
3.250
3.500
4.000
4.500
5.000
5.500
6.000
W/O With
1.0
1.2
1.3
1.6
2.1
2.1
2.4
2.9
4.83
5.78
6.25
7.51
9.54
10.22
10.68
11.78
NA
Wl
V
W/O
Shaft
Fan
With
Shaft
Fan
UA
Key
2060
2070
2080
2090
2100
2110
2120
2130
24.94
28.34
31.68
35.08
38.50
42.02
45.38
48.58
3.68
4.26
4.50
4.76
5.26
5.62
6.26
6.76
2.38
2.94
3.16
3.12
3.35
3.55
4.09
4.51
1.8750
2.1250
2.2500
2.5000
2.7500
3.0000
3.2500
3.5000
4.42
5.21
5.84
6.95
l
l
l
l
Average
Wt
lb
340
480
680
950
1320
1560
2210
2900
NA
W/O
Shaft
Fan
With
Shaft
Fan
UA
Key
24.32
27.28
30.64
33.66
37.14
40.10
43.40
45.98
3.26
3.18
3.68
3.88
4.00
4.00
4.26
4.26
...
...
...
...
2.34
2.58
2.54
2.54
1.5000
1.7500
2.0000
2.0000
2.1250
2.1250
2.2500
2.2500
NA
23.56
26.54
29.90
32.92
36.66
39.62
42.62
45.20
2.50
2.44
2.95
3.26
3.76
3.50
3.62
3.62
UA
Key
1.2500
1.3750
1.6250
1.6250
1.8750
1.8750
2.0000
2.0000
H Dimensions are for reference only and are subject to change without notice unless certified. Drives are for horizontal floor mounted operation unless specifically stated otherwise.
60 (311-110)
Z
Y
DIMENSIONS ON PAGE 60
(CA IN TABLE BELOW)
VENTED DIPSTICK
CA
SHAFT
GAP
C
GUARD
USABLE
LENGTH
X
CLEARANCE
2.6
1.3
U
O
D
V
K
Average
Weight
DRIVE
of Drive
SIZE
Only
lb n
OIL DRAIN
BOTH ENDS
Max t
NEMA
T&U
Frame
Size
143T
145T
182T
184T
213T
215T
254T
284TS 286TS 324TS 326TS 364TS 365TS 404TS 405TS 444TS 445TS
OPEN MOTORS
2060
2070
2080
2090
2100
2110
2120
2130
340
480
680
950
1320
1560
2210
2900
365
405
445
445
445
445
445
445
39.2
42.0
44.6
47.6
50.9
53.9
56.6
...
39.2
42.0
44.6
47.6
50.9
53.9
56.6
59.3
39.2
42.0
44.6
47.6
51.5
54.5
56.6
59.3
39.2
42.0
44.6
47.6
51.5
54.5
56.6
59.3
40.8
43.2
46.7
49.6
53.0
55.9
58.6
61.3
42.4
45.7
48.2
51.1
54.6
57.5
61.0
62.8
45.5
49.0
52.5
54.4
57.8
60.7
63.9
66.6
2060
2070
2080
2090
2100
2110
2120
2130
340
480
680
950
1320
1560
2210
2900
365
405
445
445
445
445
445
445
36.5
38.8
42.0
45.1
...
...
...
...
36.9
39.3
42.5
45.5
50.0
...
...
...
39.0
42.4
44.6
47.6
51.6
54.7
57.6
...
40.0
43.4
46.4
49.4
52.6
55.7
58.6
61.2
45.2
47.3
50.7
53.8
57.1
59.6
62.6
65.2
45.2
47.3
50.7
53.8
57.1
59.6
62.6
65.2
50.7
53.8
57.3
59.3
62.6
65.7
68.9
70.9
47.3
50.7
54.1
57.7
59.5
62.5
65.8
68.7
49.0
51.9
54.4
57.4
60.7
63.7
66.2
68.9
49.0
52.0
55.3
58.7
62.5
63.7
67.0
69.7
51.8
54.7
58.0
60.9
63.5
66.7
69.7
72.4
51.8
54.7
58.0
61.3
64.9
68.2
69.7
72.4
52.4
55.2
58.4
61.8
66.3
69.3
72.3
74.9
52.6
56.0
59.8
62.8
66.6
69.7
73.6
76.6
58.6
61.6
64.8
69.7
72.7
75.6
78.3
59.8
62.9
66.3
69.8
73.3
76.8
79.7
69.7
74.7
77.7
80.6
83.8
71.3
74.8
78.4
81.9
85.0
53.0
55.9
59.0
61.6
65.0
67.9
71.0
73.6
53.0
55.9
59.0
62.2
65.0
67.9
71.0
73.6
55.8
58.7
62.0
62.2
67.8
70.7
73.8
76.3
55.8
58.7
62.0
65.6
67.8
70.7
73.8
76.3
57.4
60.4
63.9
67.2
70.6
72.3
75.4
78.0
60.3
63.9
67.2
70.6
72.3
75.4
78.0
68.2
71.3
74.5
78.0
80.1
82.7
74.5
78.0
80.1
82.7
83.4
86.7
87.6
87.6
TEFC MOTORS
50.7
53.8
57.3
59.3
62.6
65.7
68.9
70.9
Refer to Pages 6 and 7 for instructions when using other than T-frame motors.
(311-110) 61
Type MM
Motor Mounts/Dimensions Inches
Standard Assemblies
Assemblies are viewed from high speed end of drive. For 3 and 9 oclock
assemblies, refer to (t) footnote below to determine dimensions FA, GA,
HA and JA. Refer to Page 58 for drive dimensions.
QA
QA
QA
H. S.
SHAFT
H. S.
SHAFT
12 O'CLOCK
9 O'CLOCK
KA
3 O'CLOCK
OSHA GUARD
MA
SHIM IF
REQUIRED
GA
MA
FA
JA
H. S.
SHAFT
HA
LA
REFER TO STD.
ASSEMBLIES ABOVE
H. S.
SHAFT
H. S.
SHAFT
L. S.
SHAFT:
L. S.
SHAFT:
SIZE 2050 . . . 56-210T & U
3&9t
Oclock HA
FA & GA Min.
Addition
12 Oclock Mounting Q t
DRIVE
SIZE
H
56
FA
140
180
210
250
280
320
JA
Max.
PA
Dimension QA
Std Assemblies
Clock Positions
GA
FA
GA
FA
GA
FA
GA
FA
GA
FA
GA
FA
GA
12
13.10
MM2040
...
16.10
...
13.10
...
16.10
...
14.10
...
17.10
...
14.86
...
17.86
...
15.86
...
18.86
...
16.60
...
19.60
...
...
18.31
...
21.10
1.84
1.84
9.60
10.31
12.60
13.10
8.32
8.32
2.00
2.00
2.00
2.00
0
0
MM2050 14.06
17.00
14.06
17.00
15.06
18.00
15.82
18.76
16.82
19.76
17.56
20.50
18.56
21.50
2.14
10.56
13.50
9.30
2.34
2.34
DRIVE
SIZE
56 thru 210
KA
LA
Motor
Mount
Wt-lb
MM2040
MM2050
13.00
15.00
2.28 l
...
55
60
KA
14.00
...
320
LA
Motor
Mount
Wt-lb
KA
2.02
...
70
...
...
16.00
LA
Motor
Mount
Wt-lb
KA
...
2.72
...
90
16.00
...
DIMENSION MA
LA
Motor
Mount
Wt-lb
56
140
180
210
250
280
320
5.27
...
118
...
12.68
15.28
13.18
15.78
12.68
15.28
11.92
14.54
11.16
13.78
10.68
13.28
10.22
12.78
H Dimensions are for reference only and are subject to change without notice unless certified.
Q When determining belt length for minimum shaft centers, follow the belt manufacturers installation allowance recommendations and also provide for future belt tensioning.
Motors may be shimmed up to 1.5.
Motor mount extends .56 below Size 2040 with 320 frame when mounted in 3 and 9 oclock positions.
l Measure () LA to left of shaft end instead of as shown; shaft extends beyond bracket.
t To determine shaft centers for 3 & 9 oclock mountings, add amount shown in the 3 & 9 oclock Addition column to the 12 oclock FA & GA dimensions.
Dimensions HA and JA will increase the same amounts.
How to Order
Your nearby Rexnord Representative or Authorized Distributor will
be pleased to analyze your new or existing application
requirements and recommend the most efficient and economical
motor mount selections. At the same time, if you wish, his wide
experience in the field of power transmission qualifies him to
examine your installation and perhaps point out additional ways to
increase efficiency and reduce cost with other Rexnord precision
products.
62 (311-110)
Type MM
Motor Mounts/Dimensions Inches
Standard Assemblies
Assemblies are viewed from high speed end of drive. For 3 and 9 oclock
assemblies, refer to (t) footnote below to determine dimensions FA, GA, HA
and JA. Refer to Page 60 for drive dimensions.
NOTE: Motor mounts are not available for Drive Sizes 2100 thru 2130 with
external backstops or drive Sizes 2060 thru 2130 with shaft fans.
(+)QA
(+)QA
QA
(-)QA
9 O'CLOCK
H. S.
SHAFT
12 O'CLOCK
H. S.
SHAFT
(-)QA
3 O'CLOCK
MA
KA
SUPPORT:
250-404T
GA
LA
FA
JA
H. S.
SHAFT
HA
REFER TO STD.
ASSEMBLIES ABOVE
H. S.
SHAFT
Figure 1
H. S.
SHAFT
DRIVE
SIZE
12 Oclock Mounting Q t
140
180
210
250
280
320
360
400
FA
GA
FA
GA
FA
GA
FA
GA
FA
GA
FA
GA
FA
GA
FA
GA
16.42
16.92
17.82
18.94
21.32
22.02
21.72
22.62
20.02
20.52
21.42
22.54
24.92
25.62
25.32
26.22
17.42
17.92
18.82
19.94
22.32
23.02
22.72
23.62
21.02
21.52
22.42
23.54
25.92
26.62
26.32
27.22
18.18
18.68
19.58
20.70
23.08
23.78
23.48
24.38
21.78
22.28
23.18
24.30
26.68
27.38
27.08
27.98
19.18
19.68
20.58
21.70
24.08
24.78
24.48
25.38
22.78
23.28
24.18
25.30
27.68
28.38
28.08
28.98
19.92
20.42
21.32
22.44
24.82
25.52
25.22
26.12
23.52
24.02
24.92
26.04
28.42
29.12
28.82
29.72
20.92
21.42
22.32
23.44
25.82
26.52
26.22
27.12
24.52
25.02
25.92
27.04
29.42
30.12
29.82
30.72
22.60
23.10
23.76
24.88
27.26
27.96
27.66
28.56
25.52
26.02
26.92
28.04
30.42
31.12
30.82
31.72
23.60
24.10
24.76
25.88
28.26
28.96
28.66
29.56
26.52
27.02
27.92
29.04
31.42
32.12
31.82
32.72
3&9t
Oclock
FA & GA
Addition
HA
Min
JA Q
Max
PA
1.96
2.40
2.50
2.32
2.10
2.20
1.90
2.00
12.92
13.42
14.32
15.44
17.82
18.52
18.22
19.12
16.52
17.02
17.92
19.04
21.42
22.12
21.82
22.72
11.48
11.98
12.76
13.88
16.26
16.96
16.66
17.56
DIMENSION MA
FC2, FC3 & FC4
L. S.
SHAFT:
MOTOR
MOUNT &
DRIVE
SIZE
MM2060
MM2070
MM2080
MM2090
MM2100
MM2110
MM2120
MM2130
Figure 2
L. S.
SHAFT:
PA
Dimension QA Standard
Assemblies Clock Positions
KA
Mtr Mt
Wt-lb
KA
LA
Mtr Mt
Wt-lb
KA
LA
Mtr Mt
Wt-lb
140
180
210
250
280
320
360
400
MM2060
MM2070
MM2080
MM2090
MM2100
MM2110
MM2120
MM2130
15.00
15.00
15.00
15.00
15.00
15.00
15.00
15.00
60
60
75
75
80
80
80
80
16.00
16.00
20.00
20.00
20.00
20.00
20.00
20.00
.08
2.80
1.92
4.94
8.38
Use
Figure
1
115
115
170
175
195
190
190
190
20.00
20.00
20.00
20.00
20.00
20.00
20.00
20.00
(+)3.52 l
(+)0.82 l
1.92
4.94
8.38
Use
Figure
1
200
200
220
225
245
240
240
240
18.74
21.46
24.42
27.44
30.96
34.00
36.88
39.46
18.24
20.96
23.92
26.94
30.46
33.50
36.38
38.96
17.48
20.20
23.16
26.18
29.70
32.74
35.62
38.20
16.74
19.46
22.42
25.44
28.96
32.00
34.88
37.46
16.24
18.96
21.92
24.94
28.46
31.50
34.38
36.96
15.74
18.46
21.42
24.44
27.96
31.00
33.88
36.46
15.36
18.06
20.80
23.82
27.26
30.30
33.18
35.76
14.60
17.32
20.04
23.06
26.50
29.54
32.42
35.00
3
()0.84 n
()2.64 n
()2.44
()2.44
()0.40
()0.40
()2.76
()2.76
12
(+)1.84 n
()1.76 n
()1.32
()1.32
(+)0.40
(+)0.40
()2.76
()2.76
2.24 n
2.24 n
3.94
3.94
2.76
2.76
2.76
2.76
H Dimensions are for reference only and subject to change without notice unless certified.
s A support is furnished only for 250T and larger frames.
Q When determining belt length for minimum shaft centers, follow the belt manufacturers installation allowance recommendations and also provide for future belt tensioning.
Motors may be shimmed up to 1.5.
For 360 and 400 frames add the following to the HA dimension: .68 for Sizes 2060 and 2070FC; .44 for Sizes 2080 thru 2130FC.
t To determine shaft centers for 3 & 9 oclock mountings, add amount shown in the 3 & 9 oclock Addition column to the 12 oclock FA & GA dimensions. Dimensions HA and JA
will increase the same amounts.
Sizes 2070, 2110 and 2130FC2: add .12 to dimensions MA & LA; Sizes 2080 & 2090FC2: add .38 to dimensions MA & LA.
l Bracket extends beyond end of shaft; (+)LA is from end of shaft, (right), to end of bracket.
n Dimension QA for Sizes 2060 and 2070FC with the 360-400 motor frames are: add .46 for 3 oclock; add .34 for 9 oclock and use 4.34 for 12 oclock.
(311-110) 63
Type MC
Motor Adapters/Dimensions Inches
Type MC motor adapters provide for quick flange mounting of
NEMA C-face motors on UltraMax Type FC drives.
BB
AA
H. S. SHAFT
KEY
FF
UA
GG
DD
MOTOR
ADAPTER &
DRIVE SIZE
H
Motor
Frame
Size
AA
BB
DD
FF
GG
HH
JJ
UA
Key
FC2
182-184
213-256
284-286
18.44
18.44
18.44
22.61
23.11
23.86
22.81
23.31
24.06
.64
.64
.64
8.502
8.502
10.502
9.25
9.25
11.50
.500
.500
.500
7.250
7.250
9.000
1.375
1.375
1.375
FC3
56-145
182-184
213-215
18.44
18.44
18.44
21.27
22.64
23.14
21.52
22.84
23.34
.64
.64
.64
4.502
8.502
8.502
7.38
9.25
9.25
.375
.500
.500
5.875
7.250
7.250
1.375
1.375
1.375
FC2
182-184
213-256
284-286
21.54
21.54
21.54
25.81
26.31
27.06
26.01
26.51
27.26
.64
.64
.64
8.502
8.502
10.502
9.25
9.25
11.50
.500
.500
.500
7.250
7.250
9.000
1.625
1.625
1.625
FC3
56-145
182-184
213-256
21.54
21.54
21.54
24.43
25.81
26.31
24.68
26.01
26.51
.64
.64
.64
4.502
8.502
8.502
7.38
9.25
9.25
.375
.500
.500
5.875
7.250
7.250
1.625
1.625
1.625
FC4
56-145
182-184
19.98
19.98
23.56
24.94
23.81
25.14
.64
.64
4.502
8.502
7.38
9.25
.375
.500
5.875
2.250
1.000
1.000
FC2
213-215
254-256
284-286
24.94
24.94
24.94
29.26
29.76
30.51
29.46
29.96
30.71
.64
.64
.64
8.502
8.502
10.502
9.25
9.25
11.50
.500
.500
.500
7.250
7.250
9.000
1.875
1.875
1.875
FC3
143-145
182-184
213-256
24.32
24.32
24.32
27.48
28.85
29.35
27.73
29.05
29.55
.64
.64
.64
4.502
8.502
8.502
7.38
9.25
9.25
.375
.500
.500
5.875
7.250
7.250
1.500
1.500
1.500
FC4
56-145
182-184
23.56
23.56
27.36
28.73
26.61
28.93
.64
.64
4.502
8.502
7.38
9.25
.375
.500
5.875
7.250
1.250
1.250
FC3
182-184
213-256
284-286
27.28
27.28
27.28
31.52
32.02
32.77
31.72
32.22
32.97
.64
.64
.64
8.502
8.502
10.502
9.25
9.25
11.50
.500
.500
.500
7.250
7.250
9.000
1.750
1.750
1.750
FC4
56-145
182-215
26.54
26.54
30.07
31.45
30.32
31.65
.64
.64
4.502
8.502
7.38
9.25
.375
.500
5.875
7.250
1.375
1.375
FC3
182-215
254-256
284-286
30.64
30.64
30.64
34.96
35.46
36.21
35.16
35.66
36.41
.64
.64
.64
8.502
8.502
10.502
9.25
9.25
11.50
.500
.500
.500
7.250
7.250
9.000
2.000
2.000
2.000
FC4
56-145
182-184
231-215
29.90
29.90
29.90
32.80
34.18
34.68
33.05
34.38
34.88
.64
.64
.64
4.502
8.502
8.502
7.38
9.25
9.25
.375
.500
.500
5.875
7.250
7.250
1.625
1.625
1.625
MC2040
MC2050
MC2060
Dimensions Inches
Drive
Type &
Reduction
MC2070
MC2080
H Dimensions are for reference only and are subject to change without notice unless certified.
Motor frames 182-256 will have conduit box mounted at 45 for drive Size 2080F3 only.
64 (311-110)
Type MP
Motor Plates/Dimensions Inches
KA
JA
RA
MA
MAX.
FLAT
RA
L. S. SHAFT
KEY
CA
H.S.SHAFT COUPLING
GUARD (WHEN
SPECIFIED)
LA
GAP
TO SUIT
MOTOR:
SHIM
BLOCKS
OR
PEDESTAL
D
DA
TA
VA
FA
Q
VA
FA
BA
DRIVE
SIZE
7.46
2100
LA
DRIVE
SIZE
H
Motor
Plate
(MP) Size
DA
.14
F2
F3
F4
2040
MP40/50
8.50
14.50
33.52
33.52
34.56
2050
MP40/50
9.60
15.60
31.62
31.62
33.18
8.66
2060
MP60/70-2
MP60/70
10.60
10.60
16.60
16.60
22.06
40.06
22.68
40.68
23.44
41.44
8.50
8.50
2110
2070
MP60/70-2
MP60/70
11.66
11.66
17.66
17.66
19.66
37.66
20.72
38.72
21.46
39.46
9.50
9.50
2120
2080
MP80/90-2
MP80/90
12.78
12.78
21.78
21.78
37.02
52.02
38.06
53.06
38.80
53.80
11.20
11.20
MP80/90-2
MP80/90
15.74
15.74
24.74
24.74
34.82
49.82
36.24
51.24
36.98
51.98
12.40
12.40
EA
FA
GA
HA
2090
DRIVE
SIZE
H
Motor
Plate
(MP) Size
AA*
BA
EA
6-HOLES
FOR HA DIA.
GRADE 5 BOLTS
2130
JA
Motor
Plate
(MP) Size
EA
AA
DA
.14
GA
LA W/O Backstop
FC2
FC3
FC4
LA W/Backstop
FC2
FC3
FC4
KA
MA
PA
RA
TA
+.20
.00
VA
Wt-lb
(w/o drive)
2040/2050
MP40/50
20.00
46.00
7.50
21.50
.50
1.000
15.50
18.00
5.00
6.70
5.90
1.50
270
2060/2070
MP60/70-2
MP60/70
25.00
25.00
40.00
58.00
10.00
10.00
18.50
27.50
.50
.50
1.000
1.000
0
1.00
20.00
22.00
23.00
23.00
6.00
6.00
8.00
8.00
5.90
5.90
1.50
1.50
272
380
2080/2090
MP80/90-2
MP80/90
30.00
30.00
60.00
75.00
11.80
11.80
27.50
35.00
.75
.75
1.500
1.500
0
1.00
23.30
31.00
26.50
26.50
6.00
6.00
9.00
9.00
8.90
8.90
2.50
2.50
874
980
2100/2110
MP100/110-2
MP100/110
35.00
35.00
60.00
86.00
14.20
14.20
27.50
40.50
.75
.75
1.500
1.500
0
2.00
30.00
36.00
31.50
31.50
6.00
6.00
12.00
12.00
8.90
8.90
2.50
2.50
942
1150
MP120/130-4
MP120/130-2
MP120/130
39.00
39.00
39.00
60.00
80.00
108.00
16.20
16.20
16.20
27.50
37.50
51.50
.75
.75
.75
1.500
1.500
1.500
2120/2130
30.00
38.24
46.00
35.50
35.50
35.50
6.00
6.00
6.00
14.00
14.24
14.00
8.90
8.90
8.90
2.50
2.50
2.50
1008
1294
1610
0
4.00
H Dimensions are for reference only and are subject to change without notice unless certified.
Q When a motor pedestal is furnished, dimension AA is 1.24" wider for MP 40/50, 1.50" wider for MP60 thru 90 and 1.00" wider for MP100 thru 130.
(311-110) 65
Type SR
Slide Rails/Dimensions Inches
Type SR slide rails can be used in conjunction with UltraMax MP
motor plates for positioning of the drive assembly, and to facilitate
chain and belt drive installation, tensioning, and service.
KB
VB
TO SUIT MOTOR:
SHIM BLOCKS
OR PEDESTAL
L. S.
SHAFT
MAX.
TRAVEL
MINIMUM
MB
DB
GB
KB
KB
VB
VB
FB
JB
KB
PB
JB
VB
FB
Motor
Plate
Size
CB
MAX.
AB
BB
NB
EB
NB
QB
AB
BB
CB
Max
DB
EB
FB
GB
HB
JB
KB
MB
NB
PB
Min
QB
VB
SR2040
MP40/50
40.00
50.00
4.20
18.26
37.40
21.50
.75
1.00
4.00
7.00
6.44
1.30
13.00
7.46
3.50
SR2050
MP40/50
40.00
50.00
4.20
19.36
37.40
21.50
.75
1.00
4.00
7.00
6.44
1.30
13.00
8.66
3.50
SR2060
MP60/70-2
MP60/70
40.00
40.00
44.00
62.00
4.20
4.20
20.36
20.36
37.40
37.40
18.50
27.50
.75
.75
1.00
1.00
4.00
4.00
7.00
7.00
6.44
6.44
1.30
1.30
15.50
15.50
8.50
8.50
3.50
3.50
SR2070
MP60/70-2
MP60/70
40.00
40.00
44.00
62.00
4.20
4.20
21.42
21.42
37.40
37.40
18.50
27.50
.75
.75
1.00
1.00
4.00
4.00
7.00
7.00
6.44
6.44
1.30
1.30
15.50
15.50
9.50
9.50
3.50
3.50
SR2080
MP80/90-2
MP80/90
60.00
60.00
64.60
79.60
3.38
3.38
27.04
27.04
56.00
56.00
27.50
35.00
1.00
1.00
1.50
1.50
6.00
6.00
9.60
9.60
7.20
7.20
2.00
2.00
19.30
19.30
11.20
11.20
4.80
4.80
SR2090
MP80/90-2
MP80/90
60.00
60.00
64.60
79.60
3.38
3.38
30.00
30.00
56.00
56.00
27.50
35.00
1.00
1.00
1.50
1.50
6.00
6.00
9.60
9.60
7.20
7.20
2.00
2.00
19.30
19.30
12.40
12.40
4.80
4.80
SR2100
MP100/110-2
MP100/110
60.00
60.00
64.60
90.60
3.38
3.38
31.66
31.66
56.00
56.00
27.50
40.50
1.00
1.00
1.50
1.50
6.00
6.00
9.60
9.60
7.20
7.20
2.00
2.00
21.80
21.80
13.54
13.54
4.80
4.80
SR2110
MP100/110-2
MP100/110
60.00
60.00
64.60
90.60
3.38
3.38
33.76
33.76
56.00
56.00
27.50
40.50
1.00
1.00
1.50
1.50
6.00
6.00
9.60
9.60
7.20
7.20
2.00
2.00
21.80
21.80
14.12
14.12
4.80
4.80
SR2120
MP120/130-4
MP120/130-2
MP120/130
60.00
60.00
60.00
64.60
84.60
112.60
3.38
3.38
3.38
36.16
36.16
36.16
56.00
56.00
56.00
27.50
37.50
51.50
1.00
1.00
1.00
1.50
1.50
1.50
6.00
6.00
6.00
9.60
9.60
9.60
7.20
7.20
7.20
2.00
2.00
2.00
23.80
23.80
23.80
14.68
14.68
14.68
4.80
4.80
4.80
SR2130
MP120/130-4
MP120/130-2
MP120/130
60.00
60.00
60.00
64.60
84.60
112.60
3.38
3.38
3.38
38.96
38.96
38.96
56.00
56.00
56.00
27.50
37.50
51.50
1.00
1.00
1.00
1.50
1.50
1.50
6.00
6.00
6.00
9.60
9.60
9.60
7.20
7.20
7.20
2.00
2.00
2.00
23.80
23.80
23.80
15.76
15.76
15.76
4.80
4.80
4.80
H Dimensions are for reference only and are subject to change without notice unless certified.
66 (311-110)
Type SB
Slide Bases/Dimensions Inches
Type SB slide bases provide for convenient positioning of UltraMax
drives, and facilitate chain and belt installation tensioning and
service. The slide base is permanently bolted to the foundation,
and when a change of position is desired, the drive is easily shifted
by loosening the gear drive foundation bolts and turning the
adjusting screws. After the desired belt or chain tension is
obtained, the drive foundation bolts are tightened, and the
machine is ready for operation. All drives on slide bases are
available with motor mounts in the 12 oclock position; Sizes 2090
and larger are also available with motor mounts in the 3 and 9
oclock positions.
CENTERLINE FOR
SLIDE BASE AND
UNIT FEET BOLTS
L. S.
SHAFT
BOLTS &
JACKSCREWS
FURNISHED
BY FALK
DB
MAX.
TRAVEL
MB
MINIMUM
GB
JB
VB
VB
FB
FB
JB
PB
Q
NB
BB
NB
EB
CB
AB
MAX.
AB
BB
CB
Max
DB
EB
FB
GB
HB
JB
MB
NB
PB
Min
VB
Wt-lb
Approx.
SB2040
SB2050
SB2060
SB2070
SB2080
SB2090
SB2100
SB2110
SB2120
SB2130
6.86
8.10
8.00
9.20
10.00
11.50
13.14
13.72
14.58
16.16
25.02
28.30
31.32
33.72
37.68
44.72
46.16
49.10
52.12
53.64
10.20
11.60
14.70
16.40
19.00
21.00
21.20
23.60
25.60
26.20
3.36
3.56
2.78
2.90
4.18
2.18
2.26
3.22
3.24
3.24
10.76
12.36
13.86
14.92
16.54
20.00
21.66
25.76
28.16
30.96
23.22
26.30
28.72
31.12
34.88
39.72
41.16
44.10
47.12
48.64
3.05
3.55
5.00
5.65
6.60
7.15
7.48
8.64
9.40
9.65
.50
.50
.62
.62
.75
1.00
1.00
1.00
1.00
1.00
.750
.875
1.000
1.125
1.250
1.500
1.500
1.500
1.750
1.750
2.50
3.00
3.50
3.50
4.00
6.00
6.00
6.00
6.00
6.00
4.10
4.70
4.70
4.70
5.70
5.70
5.70
6.76
6.76
6.76
.90
1.00
1.30
1.30
1.40
2.50
2.50
2.50
2.50
2.50
9.54
10.80
12.00
13.20
14.58
17.00
17.72
18.66
20.18
20.94
2.04
2.24
2.35
2.54
2.90
3.35
3.12
3.16
3.40
3.44
41
62
92
104
169
228
264
344
382
394
H Dimensions are for reference only and are subject to change without notice unless certified. All drives on slide bases are available with motor mounts in the 12 oclock position;
Sizes 2090 and larger are also available with motor mounts in the 3 and 9 oclock positions.
(311-110) 67
EXTERNAL BACKSTOP
C
USABLE NA
LENGTH
UA
Ratio
Range
NA
UA
Key
2100
45.10
5.06-13.95
17.09-31.39
5.24
6.22
2.7500
2.1250
2110
48.62
7.59-20.93
25.63-31.39
5.62
6.62
2120
51.98
11.39-31.39
2130
55.18
13.95-31.39
NA
42.74
3.0000
2.1250
6.22
3.2500
6.76
3.5000
NA
UA
Key
3.88
2.1250
42.26
45.70
3.82
2.1250
48.86
4.00
2.1250
51.44
4.00
2.1250
Key
3.38
1.8750
45.22
3.32
1.8750
48.60
3.74
2.0000
51.18
3.76
2.0000
H Dimensions are for reference only and are subject to change without notice unless certified.
Q Shaft diameters under 3 are held to limits of +.0000, .0005. Shaft diameters 3 and over are held to limits of +.000, .001. Shaft keyseat depth is one-half key height.
Key extends from the end of the shaft through the backstop.
68 (311-110)
Type EBS
External (Pawl Type) Backstop Selections/580 rpm or higher
Triple Reduction
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
38.44
47.08
57.66
70.62
86.50
105.90
129.70
158.90
194.60
Quadruple Reduction
Double Reduction
Nominal
Ratios
238.40
291.90
357.50
437.90
536.30
656.80
804.50
985.30
DRIVE SIZE
2100
2110
2120
2130
#60 Backstop
#20 Backstop
Nominal
Ratios
5.06
6.20
7.59
9.30
11.39
13.95
17.09
20.93
25.63
31.39
#20 Backstop
38.44
47.08
57.66
70.62
86.50
105.90
129.70
158.90
194.60
#20 Backstop
238.40
291.90
357.50
437.90
536.30
656.80
804.50
985.30
H Gear drive maximum rating at 580 rpm exceeds #60 B1F rating. #60 backstop may be
used only if required high speed shaft torque is less than 40,320 lb-in.
(311-110) 69
Type EF
Electric Fans/Dimensions Inches
Electric fans achieve thermal capacities up to twice that of shaft fans,
are unaffected by shaft rotation and speeds, and are thermostatically
controlled to shut off when not required. Electric fans can be mounted
on either side of the UltraMax and permit full use of the UltraMax
usable shaft extensions. Electric fans are available with the following
motor packages:
60 Hz, 3 Phase, 220/380 VAC
60 Hz, 3 Phase, 265/460 VAC
50 Hz, 3 Phase, 220/380 VAC
Other motor package options may be available. Consult Factory for
selection, price and delivery.
5.00
SUMP TEMPERATURE
SWITCH
B
0.75
J
0.75
7.25
0.75
K
CLEARANCE
FAN
B
D
0.75
F
CLEARANCE
0.75
.
DIA
STANDARD
LOCATION
OPTIONAL
LOCATION
H.S. END
ELECTRIC FAN,
DRIVE SIZE &
REDUCTION H
Electric Fan
Dia Inches
12
12
12
14
16
18
20
22
24.63
25.59
26.33
28.21
30.15
32.01
34.12
37.93
6.9
7.9
8.7
9.6
10.7
11.6
12.6
13.5
17.73
17.69
17.63
18.61
19.45
20.41
21.52
24.43
17.05
19.05
21.42
23.30
25.05
27.67
30.05
31.55
14.30
14.87
15.37
16.53
17.20
18.40
19.78
20.66
H Dimensions are for reference only and are subject to change without notice unless certified. Drawings are representative of
this series of drives and may not agree in exact detail for all drive sizes.
70 (311-110)
Type CT
Cooling Tubes/Dimensions Inches
Cooling tubes are an economical alternative to pumps and coolers
for thermal requirements beyond the range of fans. Water is
circulated through a series of finned tubes in the sump of the drive.
All joints and connections are external, eliminating any chance of
leakage into the drive.
A minimum flow rate of 2 gallons per minute of clean water is
required to prevent tube fouling. The maximum flow rate to prevent
tube erosion is 5 gallons per minute. Thermal power ratings are
based on a water inlet temperature of 70F (21C) with 2 gallons
per minute flow rate.
SIDE WALL
OF DRIVE
.60
WATER INLET
.500 - 14 NPT
DRIVE SIZES 2060F, 2070F, & 2080F ALL REDUCTIONS & RATIOS (1.50 - 985:1)
DRIVE SIZES 2090F2 - RATIOS (1.50 - 4.57:1 ONLY)
L. S.
END
H. S.
END
AJ
WATER
OUT
AH
WATER IN
AG
AF
.10
(.20 ON
2090F
ONLY)
AL
AX CLEARANCE
FOR TUBE REMOVAL
AK
L. S.
END
H. S.
END
AJ
WATER
OUT
AH
AF
AG
.20
(.10 ON
2120F
ONLY)
WATER IN
AK
CT2060
CT2070
CT2080
CT2090
CT2090
CT2100
CT2110
CT2120
CT2130
AL
AX CLEARANCE
FOR TUBE REMOVAL
Drive
Reduction
AF
AG
AH
AJ
AK
AL
AX
Std No.
of Tubes
FC/FZ 2, 3 & 4
FC/FZ 2, 3 & 4
FC/FZ 2, 3 & 4
FC/FZ 2, 3 & 4
FC/FZ 2 n
FC/FZ 2, 3 & 4
FC/FZ 2, 3 & 4
FC/FZ 2, 3 & 4
FC/FZ 2, 3 & 4
2.16
2.16
2.30
2.59
2.59
2.75
2.75
2.99
2.99
3.80
4.35
5.40
5.60
5.60
6.11
6.50
8.52
8.19
4.56
3.81
3.81
6.13
4.10
6.29
6.29
6.74
8.83
1.80
2.08
2.39
2.32
2.59
2.83
3.22
2.94
6.23
2.7
2.6
2.4
1.7
1.7
1.6
2.0
1.4
1.4
2.8
2.8
2.6
1.8
1.8
1.7
2.1
1.6
1.5
19.0
21.2
22.4
23.3
23.3
25.0
27.4
28.9
30.5
2
2
2
4
2
4
4
6
8
H Dimensions are for reference only and are subject to change without notice unless certified. Drawings are representative of this series of drives and may not agree in exact detail
(311-110) 71
Coupling Guards
Dimensions Inches
Falk UltraMax standard low speed coupling guards provide quick
delivery at a low price. In stock at Rexnord, each guard is
designed for a specific size UltraMax, and can be adjusted to suit
a number of standard couplings and driven equipment
requirements. The guards are 14 gauge steel, painted with
Rexnord standard paint. Safety Yellow paint can be provided at
additional cost with extended delivery.
Falk has designed the UltraMax end of the guard for close
mounting, minimal clearance and maximum guarding. The buyer
assumes full responsibility for proper guarding of the driven
machine end to applicable national and local standards.
For special, made-to-order guards, provide complete details to
your Rexnord District Office for a quotation.
.50
FA
6 - MOUNTING HOLES
.375 DIA THRU
.50
LA
BA
HA
DA
0.38
EA
0.50
0.38
FA
0.50
CA
AA
6 - MOUNTING HOLES
.375 DIA THRU
DIMENSIONS
DRIVE
SIZE
Guard
Part
Number
AA
BA
CA
DA
EA
FA
HA
LA Min-Max
Type T
Type G
2040
2050
2060
2070
2080
2090
2100
2110
2120
2130
787354
787355
787356
787357
787358
787359
787360
787361
787362
787363
13.05
13.42
15.10
16.05
17.30
18.80
20.30
23.05
24.80
27.41
10.55
10.92
12.55
13.55
14.80
16.30
17.80
20.55
22.30
25.05
3.68
3.91
3.22
3.44
3.72
4.24
4.89
5.00
5.34
5.90
8.50
9.60
10.60
11.66
12.78
15.74
17.40
19.50
21.90
24.70
4.00
4.50
4.75
5.25
5.50
6.00
6.50
7.00
7.50
8.30
3.75
5.00
5.75
7.25
7.75
9.38
11.00
11.75
13.25
14.75
13.77
15.06
16.90
18.44
20.18
23.89
26.30
29.76
33.05
37.23
6.27-11.15
7.65-13.65
8.40-15.15
9.88-18.14
10.41-19.16
12.02-22.40
13.32-25.65
14.41-27.16
15.90-30.15
17.40-33.15
1080
1090
1100
1110
1120
1130
1140
1150
1160
1170
1030
1030
1035
1040
1045
1050
1055
1060
1070
1070
72 (311-110)
UltraMax and Rexnord are registered trademarks of Rexnord Industries, LLC. Viton is a registered
trademark of DuPont. Falk is a trademark of Rexnord. All rights reserved.
CHINA
Rexnord China
Shanghai, China
Phone: 86-21-62701942
Fax: 86-21-62701943
BRAZIL
Rexnord Correntes Ltda.
Sao Leopoldo - RS
Phone: 55-51-579-8022
Fax: 55-51-579-8029
EUROPE
Rexnord NV/SA
Mechelen, Belgium
Phone: 32-15-.443811
Fax: 32-15-443860
CANADA
Rexnord Canada Ltd.
Scarborough, Ontario
Phone: 1-416-297-6868
Fax: 1-416-297-6873
Rexnord Industries, LLC, Gear Group, 3001 West Canal Street, Milwaukee, WI 53208-4200 USA
Phone: 414-342-3131
Fax: 414-937-4359
2007 Rexnord Industries LLC
LATIN AMERICA
Rexnord International, Inc.
Milwaukee, Wisconsin
Phone: 1-414-643-2366
Fax: 1-414-643-3222
E-mail: international2@rexnord.com
MEXICO
Rexnord S.A. de C.V.
Queretaro, Qro.
Phone: 52-442-218.5000
Fax: 52-.442-218-1090
SINGAPORE
Rexnord International, Inc.
Singapore City, Singapore
Phone: 65-6338-5622
Fax: 65-6338-5422
UNITED STATES
Customer Service
Phone: 1-866-REXNORD
(1-866-739-6673)
Fax: 1-614-675-1898
E-mail: rexnordcs(state)@rexnord.com
Example: rexnordcsohio@rexnord.com
ALL COUNTRIES NOT LISTED
Rexnord International
Milwaukee, Wisconsin
Phone: 1-414-643-2366
Fax: 1-414-643-3222
E-mail: international1@rexnord.com
311-110