Académique Documents
Professionnel Documents
Culture Documents
Mar.2007
M260 HW Specification
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 1 / 75
M260 HW spec
Mar.2007
Document Information
Revision Draft vision Date Mar 2007 History of the evolution Creation as Draft
Overview
This document defines and specifies the FLYFOT M260 module with 32 Mb of Flash memory and 8 Mb of SRAM (32/8), which support GSM/GPRS function.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 2 / 75
M260 HW spec
Mar.2007
Contents
Document Information .................................................................................................................................... 2 Overview ......................................................................................................................................................... 2 Caution ............................................................................................................................................................ 6 Trademarks...................................................................................................................................................... 6 1 General description ...................................................................................................................................... 7 1.1 General information .......................................................................................................................... 7 1.2 Function description .......................................................................................................................... 8 1.2.1 RF functionalities ................................................................................................................... 9 1.2.2 Baseband functionalities.................................................................................................... 9 1.3 Firmware ........................................................................................................................................... 9 2 Interfaces .................................................................................................................................................... 10 2.1 General Purpose Connector (GPC) ................................................................................................. 10 2.2 Power supply ................................................................................................................................... 11 2.2.1 Power supply description ..................................................................................................... 11 2.2.2 Power consumption .............................................................................................................. 12 2.3 Electrical information for digital I/O............................................................................................... 15 2.4 LCD interface.................................................................................................................................. 15 2.4.1 I2C interface.......................................................................................................................... 16 2.5 Keyboard interface .......................................................................................................................... 17 2.6 Main Serial link (UART1)............................................................................................................... 18 2.6.1 Typical implementation with a RS232 Terminal .................................................................. 20 2.6.2 Typical implementation with a microprocessor.................................................................... 20 2.7 SIM interface................................................................................................................................... 21 2.7.1 General Description.............................................................................................................. 21 2.7.2 SIM socket connection ......................................................................................................... 23 2.8 General Purpose Input/Output.................................................................................................... 24 2.9 Analog to Digital Converter ......................................................................................................... 25 2.9.1 How to define R1 and C1 ..................................................................................................... 26 2.10 Audio interface .............................................................................................................................. 26 2.10.1 Main audio interface........................................................................................................... 27 2.10.1.1 Main Microphone Inputs (MIC1) ............................................................................ 27 2.10.1.2 Main speaker outputs (SPK1).................................................................................. 28 2.10.2 Auxiliary audio interface .................................................................................................... 29 2.10.2.1 Auxiliary Microphone Inputs (MIC2) ..................................................................... 29 2.10.2.1.1 Differential connection ......................................................................................... 30 2.10.2.1.2 Single-ended connection ...................................................................................... 31 2.10.2.1.3 Auxiliary speaker outputs characteristics ............................................................. 32 2.10.3 Buzzer Output..................................................................................................................... 32 2.10.4 Hand-free Speaker.............................................................................................................. 33
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 3 / 75
M260 HW spec
Mar.2007
2.11 Battery charging interface ............................................................................................................. 33 2.11.1 Li-ion charging procedure ............................................................................................. 34 2.12 ON / OFF............................................................................................................................... 35 2.12.1 Operating sequences..................................................................................................... 35 2.12.1.1 Power ON ................................................................................................................ 35 2.12.1.2 Power OFF .............................................................................................................. 36 2.12.2 Reset signal (~RST) ................................................................................................... 37 2.12.2.1 Reset sequence ........................................................................................................ 38 2.13 External Interrupt (~INTR) ...................................................................................................... 39 2.14 VCC output ................................................................................................................................... 39 2.15 VCC_RTC (REAL TIME CLOCK SUPPLY)............................................................................ 40 2.15.1 Interface description ........................................................................................................... 40 2.15.2 Typical implementation: ........................................................................................ 41 2.15.2.1 Capacitor ................................................................................................................. 41 2.15.2.2 Super Capacitor ....................................................................................................... 41 2.15.2.3 Battery cell with regulator ....................................................................................... 42 2.15.2.4 Non Rechargeable battery ....................................................................................... 42 2.16 RF interface ................................................................................................................................... 43 2.16.1 RF connection .................................................................................................................... 43 2.16.2 RF performances ................................................................................................................ 45 2.16.3 Antenna specifications........................................................................................................ 45 3 Technical specifications ............................................................................................................................. 46 3.1 Interface........................................................................................................................................... 46 3.2 Environmental Specifications..................................................................................................... 50 3.3 Mechanical specifications ............................................................................................................... 51 3.3.1 Physical characteristics......................................................................................................... 51 3.3.2 Mechanical drawings............................................................................................................ 51 4 Connectors and peripheral devices references ........................................................................................... 54 4.1 General Purpose Connector............................................................................................................. 54 4.2 SIM Card Reader............................................................................................................................. 54 4.3 Microphone ..................................................................................................................................... 54 4.4 Speaker............................................................................................................................................ 55 4.5 Antenna Cable ................................................................................................................................. 55 4.6 GSM antenna................................................................................................................................... 55 5 Design Guidelines ...................................................................................................................................... 56 5.1 Hardware and RF ............................................................................................................................ 56 5.1.1 EMC recommendations........................................................................................................ 56 5.1.2 Power Supply ....................................................................................................................... 56 5.1.3 Layout requirement .............................................................................................................. 57 5.1.4 Antenna................................................................................................................................. 58 5.2 Mechanical integration .................................................................................................................... 58
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 4 / 75
M260 HW spec
Mar.2007
5.3 Firmware upgrade ........................................................................................................................... 58 5.3.1 Nominal upgrade procedure ................................................................................................. 58 5.3.2 Backup procedure................................................................................................................. 59 5.3.3 FLYFOT M260 Module Application Notes.......................................................................... 59 6 Appendix .................................................................................................................................................... 60 6.1 FLYFOT acceptance test ................................................................................................................. 60 6.2 Standards and Recommendations.................................................................................................... 62 6.3 Safety recommendations (for information only) .......................................................................... 64 6.3.1 RF safety............................................................................................................................ 64 6.3.1.2 Exposure to RF energy .............................................................................................. 64 6.3.1.3 Efficient terminal operation.................................................................................... 65 6.3.1.4 Antenna care and replacement................................................................................... 65 6.3.2 General safety................................................................................................................... 66 6.3.2.1 Driving ...................................................................................................................... 66 6.3.2.2 Electronic devices...................................................................................................... 66 6.3.2.3 Vehicle electronic equipment..................................................................................... 66 6.3.2.4 Medical electronic equipment ................................................................................... 66 6.3.2.5 Aircraft ...................................................................................................................... 67 6.3.2.6 Children ..................................................................................................................... 67 6.3.2.7 Blasting areas ............................................................................................................ 67 6.3.2.8 Potentially explosive atmospheres ............................................................................ 67 6.4 Application notes for the SIM interface .......................................................................................... 68 6.5 General Purpose Connector data sheet ............................................................................................ 69
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 5 / 75
M260 HW spec
Mar.2007
Caution
Information furnished herein by FLYFOT is accurate and reliable. However no responsibility is assumed for its use. Please read carefully the safety precautions for a terminal based on FLYFOT M260 module.
Trademarks
Some mentioned products are registered trademarks of their respective companies.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 6 / 75
M260 HW spec
Mar.2007
1 General description
1.1 General information
M260 module is a self-contained GSM 900/1800 GPRS dual-band module including the following features: 58 x 32 x 3.9 mm 2 Watts EGSM 900 radio section running under 3.8 Volts 1 Watt GSM1800 radio section running under 3.8 Volts 1.8V/3V SIM interface Real Time Clock with calendar Battery charger Echo Cancellation + noise reduction Full GSM or GSM/GPRS software stack Hardware GPRS class 10 capable Complete shielding Complete interfacing: o Power supply o Serial link o Audio o SIM card o Keyboard o LCD (not available with AT commands)
M260 module has two external connections: RF interface General Purpose Connector (GPC) to Digital, Keyboard, Audio and Supply
FLYFOT M260 module is designed to fit in very small terminals and only some custom functions have to be added to make a complete bi-band solution: Keypad and LCD module Earpiece and Microphone Base connector Battery Antenna SIM connector Dual-band
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 7 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 8 / 75
M260 HW spec
Mar.2007
1.2.1 RF functionalities
The RF functionalities comply with the Phase II recommendation. The frequencies are EGSM 900 TX: 880 to 915 MHz RX: 925 to 960 MHz DCS1800 TX: 1710 to 1785 MHz RX: 1805 to 1880MHz PCS1900 TX: 1850 to 1910 MHz RX: 1930 to 1990MHz
The RF part is based on a specific dual-band chip including: Low-IF Receiver Dual RF synthesizer Digital IF to Baseband Converter Offset PLL transmitter Dual-band PA module
1.3 Firmware
FLYFOT M260 module is designed to be integrated into various types of applications such as handsets or vertical applications (telemetry, multimedia, etc). For vertical applications, the firmware offers a set of AT commands to control the module. With this standard software, some interfaces of the module are not available since they are dependent on the peripheral devices connected to the module. They are the LCD interface and the I C bus.
2
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 9 / 75
M260 HW spec
Mar.2007
2 Interfaces
2.1 General Purpose Connector (GPC)
A 60 pins connector is provided to interface the M260 module with a board containing either a LCD module, or a keyboard, or a SIM connector, or a battery connection... The interfaces available on the GPC are described in the next paragraphs.
1
Please be aware that some of these interfaces can not be handled when using the M260 module driven by AT commands: LCD interface. This symbol is used to indicate the interfaces not available with AT commands. These functions have then to be managed externally i.e. using the main processor of the application.
The communication interface connector is a 60 pins connector with 0.5mm pitch from KYOCERA / AVX group with the following reference (see chapter connectors reference for further details): 14 5087 060 930 861. The matting connector has the following reference: 24 5087 060 X00 861. X = 2 or 9
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 10 / 75
M260 HW spec
Mar.2007
In communication mode, a GPRS class 10 terminal emits 1154s radio bursts every 4.615ms. VBATT is used to supply the RF part and the base band part.
Notes : VBATT : supplies directly the RF components with 3.6 V. It is essential to minimize the voltage ripple at this connection in order to avoid any phase error. The RF Power Amplifier current (2.0A peak in GSM /GPRS mode) flows with a ratio of 1/8 of the time, around 577s every 4.615ms for GSM /GPRS class 2. The rising time is around 10s.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 11 / 75
M260 HW spec
Mar.2007
The FLYFOT M260 module shielding case is the grounding. The ground has to be connected on the motherboard through a complete layer on the PCB.
Power Supply Voltage VMIN VBAT 3.4V(*) VNOM 3.8V VMAX 4.2V(**) Ripple max (Uripp) 50mVpp for freq<200kHZ
(*) : This value has to be guarantied during the burst (with 2.0A Peak in GSM or GPRS mode) (**): Max operating Voltage Stationary Wave Ratio (VSWR) 2:1
When supplying the module with a battery, the total impedance (battery + protections + PCB) should be <150 m
Power consumption in OFF mode (Module supplied, OFF state, no software running) Conditions Overall consumption OFF INOM 50uA IMAX 60uA
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 12 / 75
M260 HW spec
Mar.2007
Power consumption in EGSM/GPRS 900 MHz mode class 10 Conditions VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ During TX bursts @ PCL5* During RX bursts Average 1RX/1TX@PCL5* Average 1RX/1TX@PCL8* Average GPRS Cl 10 (3Rx/2Tx) @Pcl5 Average GPRS Cl 10(3Rx/2Tx) @Pcl8 Average Idle mode INOM 1.7A peak 75mA peak 270mA 180mA 540mA 360mA 2.2mA IMAX 2.0A peak 80mA peak 320mA 200mA 640mA 400mA 3mA
(*) : PCL : Power Control Level. PCL 5: 2W emission requested (Max power) PCL 8: 0.5W emission requested
Power consumption in GSM/GPRS 1800 MHz mode class 10 Conditions VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ During TX bursts @ PCL0* During RX bursts Average 1RX/1TX@PCL0* Average 1RX/1TX@PCL3* Average GPRS Cl 10 (3Rx/2Tx) @PCL0 Average GPRS Cl 10 (3Rx/2Tx) @Pcl3 Average Idle mode INOM 1.3A peak 75mA peak 240mA 150mA 480mA 300mA 2mA IMAX 1.7A peak 80mA peak 270mA 180mA 540mA 360mA 3mA
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 13 / 75
M260 HW spec
Mar.2007
Power consumption in GSM/GPRS 1900 MHz mode class 10 Conditions VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ VBATT+ During TX bursts @ PCL0* During RX bursts Average 1RX/1TX@PCL0* Average 1RX/1TX@PCL3* Average GPRS Cl 10 (3Rx/2Tx) @PCL0 Average GPRS Cl 10 (3Rx/2Tx) @Pcl3 Average Idle mode INOM 1.3A peak 75mA peak 240mA 150mA 480mA 300mA 2mA IMAX 1.7A peak 80mA peak 270mA 180mA 540mA 360mA 3mA
Power Supply Pinout Signal VBATT+ GND Pin number 28,29,30,31,32 Shielding the four legs have to
The grounding connection is done through the shielding be soldered to the ground plane.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 14 / 75
M260 HW spec
Mar.2007
To interface the M260 module digital signals with other logics: 3V logic: some serial resistors (between 2.2K and 4.7K) can be added on the lines For higher voltage logics, a resistor bridge or a level shifter IC can be added.
The M260 Series can be connected to a LCD module driver the IIC interface.
through
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 15 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 16 / 75
M260 HW spec
Mar.2007
The Keyboard Scanner (KBS) implements all the logic necessary to interface matrix keyboard with up to 28 keys(see figure 3 of below) to the System Controller.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 17 / 75
M260 HW spec
Mar.2007
Keyboard definition: Key number 5 16 10 3 14 2 0 12 21 22 25 18 define Digital key 1 Digital key 3 Digital key 5 Digital key 7 Digital key 9 * SEND MENULEFT RIGHT UP LEFT SIDEUP Key number 11 4 15 9 8 13 6 17 24 23 19 define Digital key 2 Digital key 4 Digital key 6 Digital key 8 Digital key 0 # CLEAR MENURIGHT OK DOWN SIDEDOWN
Additional comments on Keyboard: The exemplify keys are defined, that keys that unmentioned in table, can be defined by updating software.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 18 / 75
M260 HW spec
Mar.2007
Pin description Signal CT103/TXD0 CT104/RXD0 CT105/RTS0 CT106/CTS0 CT107/DSR0 CT108/DTR0 CT109/DCD0 CT125/RI0 GND Pin number 20 45 30 37 36 34 51 54 Shielding legs I/O O I I O O I O O I/O TYPE CMOS 1X CMOS 1X 1X CMOS CMOS/2x CMOS/2x Description Transmit serial data Receive serial data Ready to Send Clear to send Data set ready Data terminal ready Data carrier detect Ring indicator Ground
The rising time and falling time of the reception signals (mainly CT103) have to be less than 200 ns. The M260 module has been designed to be operated using all the serial interface signals or several of them. In particular, it is possible to transmit between module and external CPU through only TXD1 and RXD1.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 19 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 20 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 21 / 75
M260 HW spec
Mar.2007
The following references can be used: Pin description Signal SIMCLK SIMRST SIMDATA SIMVCC Pin number 2 3 4 5 I/O O O I/O O I/O type 2X 2X CMOS/3X Supply Description SIM Clock SIM reset SIM DATA SIM Power supply
Electrical Characteristics Parameter SIMDATA VIH SIMDATA VIL SIMRST SIMDATA SIMCLK VOH SIMRST SIMDATA SIMCLK VOL SIMVCC Output Voltage SIMCLK Rise/Fall Time SIMRST, SIMDATA Rise/Fall Time SIMCLK Frequency ISIM_VCC<=6mA 2.70 2.80 2.85 V Sink current = 200uA 0.1 V Conditions IIH = 20uA IIL = 1mA Source current =20uA SIM_VCC-0.1V Min 0.7 x SIM_VCC 0.3xSIM_VCC Typ Max Unit V V V
50
nS
uS
3.25
MHz
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 22 / 75
M260 HW spec
Mar.2007
Typical implementation:
SIM socket
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 23 / 75
M260 HW spec
Mar.2007
2.8
The FLYFOT M260 module provides 9 General Purpose I/O, 2 General Purpose Output, 1 General Purpose input and 1 PWM Output. They are used to control any external device such as a LCD or a Keyboard backlight. Pin description Signal GPIO0 GPIO1 GPIO2 GPIO4 GPIO5 GPIO6 GPIO7 GPIO8 GPIO9 GPON1 GPON2 GPI1 PWM Pin number 49 34 27 52 43 26 44 48 53 51 47 18 35 I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O I O Description General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose I/O General Purpose output General Purpose output General Purpose input General Purpose input FLASH LED Multiplexed with
(*)The FLASH LED signal can be used to drive a LED through an open-collector transistor according to the module activity status.
M260 module status Module OFF Permanent Flash LED on for 1s, off for 1s Module switch ON, not registered on the network Module switch on, registered on the network, communication in progress
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 24 / 75
M260 HW spec
Mar.2007
2.9
The FLYFOT M260 module provides an Analog to Digital Converter (ADC) input. This ADC section is specified for voltage and temperature measurements. Its input channel required for T and V measurement, as well as battery type recognition. This converter is a 12 bits one, ranging from 0 to 2.8V. Pin description Signal AUXADC2 Pin number 17 I/O I I/O type Analog Description A/D converter
Electrical characteristics Parameter Resolution Input signal range ADC Reference Accuracy Min 12 0 0.22 2.8 0.25 Max Unit bits V
M260 module also monitors the temperature of the battery through the AUXV0 pin that has to be connected to a temperature sensor inside the battery (a NTC resistor for instance).
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 25 / 75
M260 HW spec
Mar.2007
R1= 47K
BAT-TEMP(-20) = 2.42V
BAT-TEMP(55) = 0.49V R(-20) = R1//CTN(-10) = 40K R(+55) =8K With C=10nF: RC(-20) = 400us RC(+55) = 80us
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 26 / 75
M260 HW spec
Mar.2007
MIC1 input connect C1 = C2= C3 = 39pF R1 = R2 = 0 ohm C1 has to be the nearest possible to the microphone. Microphone manufacturers provide this capacitor directly soldered on the microphone. R1, R2, C2 and C3 have to be put near the M260 Series connector and can be removed according to their environment (ground plane, shielding, etc). The best way is to plan all the components and to remove those that are not necessary to filter out the TDMA noise on the audio path.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 27 / 75
M260 HW spec
Mar.2007
Recommended characteristics for the microphone: 2V 0.5mA 2.2 K Sensitivity -40 to 50dB SNR > 60dB Frequency response compatible with the GSM specifications
Pin description Signal MIC1P MIC1N Pin number 38 37 I/O I I I/O type Analog Analog Description Microphone 1 positive input Microphone 1 negative input
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 28 / 75
M260 HW spec
Mar.2007
Recommended characteristics for the speaker: Type : 50mW, electro-magnetic Impedance : 32 Ohm Sensitivity:110 dB SPL min. Frequency response compatible with the GSM specifications Pin description Signal SPK1P SPK1N Pin number 23 24 I/O O O I/O type Analog Analog Description SPK 1 positive output SPK 1 negative output
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 29 / 75
M260 HW spec
Mar.2007
Figure 4 : MIC2 inputs (differential connection) R1 = R4 = from 100 to 330 R2 = R3 = usually between 1Kand 3.3K as per the microphone characteristics C1 = 10pF to 33pF C2 = C3 = C4 = 47pF to 100pF C5 = 47uF L1 = L2 = 100nH R1 and R4 are used as a voltage supply filter with C5. C1 has to be the nearest possible to the microphone. Microphone manufacturers provide this capacitor directly soldered on the microphone. C2 has to be very close to the M260 connector. L1, L2, C3 and C4 have to be put near the M260 connector and can be removed according to their environment (ground plane, shielding ...etc). The best way is to plan all the components and to remove those which are not necessary to filter out the TDMA noise on the audio path.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 30 / 75
M260 HW spec
Mar.2007
Figure 5 : MIC2 inputs (single-ended connection) Note: VAUDIO must be very clean in single-ended connection (for example, VCC plus filter cell like RC or LC). R1 = from 100 to 330 R2 = usually between 1Kand 3.3Kas per the VAUDIO voltage level and the microphone characteristics C1 = 10pF to 33pF C2 = C3 = C5 = 47pF to 100pF C4 = 47uF L1 = L2 = 100nH R1 is used as a voltage supply filter with C4. C5 has to be the nearest possible to the microphone. Microphone manufacturers provide this capacitor directly soldered on the microphone. C1, C2, C3 have to be very close to the M260 connector. L1, and L2 has to be put near the M260 module connector and can be removed according to their environment (ground plane, shielding ...etc). The best way is to plan all the components and to remove those which are not necessary to filter out the TDMA noise on the audio path.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 31 / 75
M260 HW spec
Mar.2007
C1=0.1uF Recommended characteristics for the buzzer: Type: Electromagnetic Impedance : 7 to 30 ohm Sensitivity : 90 dB SPL min @ 10 cm Pin description Signal BUZ Pin number 25 I/O O I/O type Analog Description BUZ positive output
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 32 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 33 / 75
M260 HW spec
Mar.2007
Electrical Characteristics Parameter CHARGE IN voltage (for I=Imax) CHARGE IN Current Min +VBAT max+0.7V Max 5.5 800 Type Unit V mA
2.11.1
Charge the Li-ion battery during this procedure the voltage of the battery is accurately monitored. The Li-ion charging involves two phases. During the first phase, the battery is charged with a constant current until its voltage reaches 4.1V*. During the second phase the constant current is pulsed by the module. The width and the frequency of the pulse change during this phase in order to ensure a safety charge. The battery is considered as fully charged when, after a pulse, the voltage remains at a 4.1V* during more than 10s. The Li-ion battery must have an included safety circuit to avoid any discharge or overcharge. The manufacturer inside the battery delivers this circuit pack. The impedance of this safety circuit has to be the lowest possible in order to reduce the drop-out of the voltage. This drop-out is due to the RF Power Amplifier current (up to 2.0A). A maximum of 150m is required. (*): To be parameterized as per battery manufacturer
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 34 / 75
M260 HW spec
Mar.2007
2.12
ON / OFF
This input is used to switch ON or OFF the M260 Series module. A high level signal, that more than 14ms, has to be provided on the pin ON/~OFF to switch ON the module. The level of the voltage of this signal has to be maintained between 2.4V and VBATT. To be able to switch OFF the module, the pin ON/OFF has to be keeping high level signal during a minimum of 1000ms. Through the firmware, the module can be switched off (using the CPOF command). Pin description Signal ON/OFF Pin number 58 I/O I I/O type CMOS Description Module Power ON/OFF
Operating conditions Parameter VIL VIH I/O Type Min 0 2.4 Max 0.3 VBATT Unit V V
Once the module supplied, the application must set the ON/OFF signal to high to start the module power ON sequence. The ON/OFF signal must be hold for 1000ms minimum. After this time, an internal mechanism keeps it on hold. During the power ON sequence, an internal reset is automatically performed by the module for 240ms (typical). During this phase, any external reset should be avoided. Once the initialization is complete (timing is SIM and network dependent) the AT interface answers OK the application . For further to details, please check the AT commands manual (+WIND, +WAIP)
2
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 35 / 75
M260 HW spec
Mar.2007
Power-ON sequence
For this, the application has to send AT.If the application manages hardware flow
control, the AT commands can be sent during the initialization phase. Another solution is to use the +WIND command to get on unsolicited status from the module.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 36 / 75
M260 HW spec
Mar.2007
Electrical Characteristics Parameter Input Impedance ( R ) Input Impedance ( C ) Min 4.7 10 Max Unit K nF
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 37 / 75
M260 HW spec
Mar.2007
Operating conditions Parameter *VT*VT+ VOL VOH 2.0V *VT-, VT+: hysteresis level Min 1.1V 1.7V Max 1.2V 1.9V 0.4V IOL=-50uA IOH=50uA Conditions
Additional comments on RESET: The RESET process is activated either by the external ~RST signal or by an internal signal (coming from a RESET generator). This automatic reset is activated at Power-up. The module remains in reset mode as long as the RST signal is held low. This signal should be used only for emergency resets. A software reset will be preferred to a HW reset.
For this, the application has to send AT . If the application manages hardware flow control, the AT commands can be sent during the initialization phase. Another solution is to use the +WIND command to get an unsolicited status from the module.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 38 / 75
M260 HW spec
Mar.2007
2.13
The M260 Series provides an external interrupt input (not managed in the standard AT commands firmware). This input is very sensitive and an interrupt is activated on high to low edge. If this signal is not used it can be left open. If used this input has to be driven by an open collector or an open drain. This input is used for instance to power OFF automatically the module.
Pin description Signal ~INTR(GPIO7) Pin number 44 I/O I I/O type CMOS Description Active low
Pin description Signal D3VDD AVDD_HFA Pin number 50 41 I/O O O I/O type Supply Supply Description Digital supply Digital supply
Operating conditions Output voltage (V) Min VCC 1.35 Max 3.45 Output current(mA) Max 150
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 39 / 75
M260 HW spec
Mar.2007
2.15
Operating conditions Parameter Input voltage Input Current Output voltage Output current VBACK < VBAT - 0.5V 2.4 Condition Min -0.5 Max 5.7 1 3.09 2 Unit V uA V mA
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 40 / 75
M260 HW spec
Mar.2007
2.15.2
Typical implementation:
2.15.2.1 Capacitor
Estimated range with 0.47 Farad Gold Cap : 2 hours min. Note: the Gold Capacitor maximum voltage is 2.5 V.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 41 / 75
M260 HW spec
Mar.2007
~3 days.
Warning : Before battery cell assembly insure that cell voltage is lower than 2.75V to avoid any damage to the M260 module.
Estimated range with 85mAh battery: 4000 h minimum Note: The non rechargeable battery is always active, except when the module is ON.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 42 / 75
M260 HW spec
Mar.2007
2.16 RF interface
Three types of RF connection are available:
2.16.1 RF connection
Two land patterns and one connector set on the PCB to support the module connecting with antenna and application board. 1 Through RF connector P101 connects to application board with matching RF cable. This cable can be used muRatas MXTK92XXXX, which has one or two connectors, also the length can be changed.
2 Connect to Antenna pad with an antenna directly. Below is the antenna matching circuit.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 43 / 75
M260 HW spec
Mar.2007
3) Through soldering RF cable to other application board. Solder cable corn to solder pad and GND to GND pad.
Notes: The antenna cable and connector should be chosen in order to minimize losses in the frequency bands used for GSM 900MHz, DCS1800MHz and PCS1900MHz. 0.5dB can be considered as a maximum value for insert loss between the module and an external connector.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 44 / 75
M260 HW spec
Mar.2007
2.16.2 RF performances
RF performances are compliant with the ETSI recommendation 05. The main parameters for Receiver are: EGSM/900 Sensitivity: < -102dBm Static & TUHigh DCS1800 Sensitivity: < -102dBm Static & TUHigh PCS1900 Sensitivity: < -102dBm Static & TUHigh Selectivity @ 200 kHz: > +9dBc Selectivity @ 400 kHz: > +41dBc Dynamic range: 63dB Co-channel rejection: >= 9dBc And for Transmitter: Maximum output power (EGSM): 33dBm +/- 2 dB at ambient temperature Maximum output power (DCS1800/PCS1900): 30dBm +/- 2 dB at ambient temperature Minimum output power (EGSM): 5dBm +/- 5 dB at ambient temperature Minimum output power (DCS1800/PCS1900): 0dBm +/- 5 dB at ambient temperature H2 level: < -30dBm H3 level: < -30dBm Noise in 925 - 935 MHz: < -67dBm Noise in 935 - 960 MHz: < -79dBm Noise in 1930 - 1990 MHz (GSM1900 band): < -71dBm Phase error at peak power: < 5 RMS Frequency error: +/- 0.1 ppm max
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 45 / 75
M260 HW spec
Mar.2007
3 Technical specifications
3.1 Interface
Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Name CHG_ IN SIMCLK SIMRST SIMDATA SIMVCC N/A ROW0 ROW1 ROW2 ROW3 N/A COL0 COL1 COL2 COL3 N/A AUXADC2 I Analog Auxiliary ADC input Can be as ADC input for battery temperature measurement I/O I/O I/O I/O CMOS/1X CMOS/1X CMOS/1X CMOS/1X Keyboard column Keyboard column Keyboard column Keyboard column I/O I/O I/O I/O CMOS/1X CMOS/1X CMOS/1X CMOS/1X Keyboard ROW Keyboard ROW Keyboard Row Keyboard Row I/O I O O I/O O I/O type Supply 2X 2X CMOS/3X Supply Description Supply charging for battery Comment High current
Clock for SIM interface Reset for SIM interface I/O for SIM Interface SIM card supply 6mA max
18 19
GPI1 CT105/RTS0
I I
CMOS CMOS
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 46 / 75
M260 HW spec
Mar.2007
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
CT104/RXD0 SPK2P SPK2N SPK1P SPK1N BUZ GPIO6 GPIO2 +VBATT +VBATT +VBATT +VBATT +VBATT VCC_RTC GPIO1 PWM1 SIMPRES MIC1N MIC1P MIC2N MIC2P AVDD_HFA RXD1 GPIO5 GPIO7/~INTR CT103/TXD0
1X Analog Analog Analog Analog Analog CMOS CMOS Supply Supply Supply Supply Supply Supply CMOS CMOS CMOS Analog Analog Analog Analog Supply 1X CMOS CMOS CMOS
RS232 interface Receiver SPK2 positive output SPK2 negative output SPK1 positive output SPK1 negative output BUZ OUTPUT General purpose I/O General purpose I/O Battery input Battery input Battery input Battery input Battery input RTC Back-up battery General purpose I/O PWM output SIM card detect MIC1 negative output MIC1 Positive input MIC2 negative input MIC 2 positive input 2.8V digital supply output RS232 interface Receiver General purpose I/O General purpose I/O RS232 interface transmit ~INTR 150mA max For tracer High current High current High current High current High current Analog output audio
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 47 / 75
M260 HW spec
Mar.2007
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
CT106/CTS0 GPON2 GPIO8 GPIO0 D3VDD GPON1 GPIO4 GPIO9 RSTON TXD1 SCL SDA ON/OFF CHG_IN CHG_IN
1X CMOS CMOS CMOS Supply CMOS CMOS CMOS CMOS/1X CMOS 1X CMOS/1X CMOS Supply Supply
RS232 interface Clear to sent General Purpose output General purpose I/O General purpose I/O 2.8V digital supply output General Purpose output General purpose I/O General purpose I/O Module reset RS232 interface transmit I C interface clock I C Interface data Power ON/OFF control Supply charging Supply charging for for battery battery Active high High current High current
2 2
100mA max
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 48 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 49 / 75
M260 HW spec
Mar.2007
3.2
Environmental Specifications
Conditions Operating / Full GSM specification compliant Storage Temperature range - 10 to + 55
- 30 to + 85
ENVIRONNEMENTAL CLASSES Storage 1.2 -25 class Transportation class 2.3 -40 72h Operating (port use ) class 7.3 -20(GSM900) -10(GSM1800/1900) 16h 16h 16h
72h
+70
72h
+70
72h
+55
+40
2cycles
+40
Damp heat
Sinusoidal vibration
5-62Hz: 5mm/s 62-200Hz: 2m/s2 3x5 sweep cycles 5-20Hz:0.96m2/ s3 20-500Hz:-3dB/ oct 10-12Hz: 0.96m2/s3 12-150Hz: -3dB /oct 3 x 30 min
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 50 / 75
M260 HW spec
Mar.2007
3X10 min
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 51 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 52 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 53 / 75
M260 HW spec
Mar.2007
The stacking height is 3.0 mm. For further details see GPC data sheets in appendix. More information is also available from http://www.avxcorp.com
X=2 or 9
(connector)
MOLEX
91236-0002
(holder)
(see
4.3 Microphone
Possible suppliers:
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 54 / 75
M260 HW spec
Mar.2007
PANASONIC HOSIDEN
4.4 Speaker
Possible suppliers: PHILIPS SANYO HOSIDEN PRIMO
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 55 / 75
M260 HW spec
Mar.2007
5 Design Guidelines
The purpose of the following paragraphs is to give design guidelines.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 56 / 75
M260 HW spec
Mar.2007
the emissions spectrum the phase error and frequency error Warning: Careful attention should be paid to: Quality of the power supply : Low ripple, PFM or PSM systems should be avoided (PWM converter preferred). Capacity to deliver high current peaks in a short time (pulsed radio emission).
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 57 / 75
M260 HW spec
Mar.2007
5.1.4 Antenna
Warning: M260 strongly recommends to work with an antenna manufacturer either to develop an antenna adapted to the application or to adapt an existing solution to the application. The antenna adaptation (mechanical and electrical adaptation) is one of the key issues in the design of a GSM terminal.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 58 / 75
M260 HW spec
Mar.2007
The necessary serial signals to proceed with the Xmodem downloading are: Rx, Tx, RTS, CTS and GND.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 59 / 75
M260 HW spec
Mar.2007
6 Appendix
6.1 FLYFOT acceptance test
These tests are FLYFOT internal qualification tests. They are performed on a FLYFOT evaluation platform (module on test board). Test Performance test Applied standard Mobile station (MS) conformance specification; Part 1: Conformance specification (release 5). 3GPP TS 51.010 v5.0.0 (2002-09) Acceptance criteria Full conformity to the recommendation regarding the main RF parameters.
Cooking test
The test continues even after the Cooking Test milestone has been reached Thermal shocks IEC 68-2-14 Full conformity to the recommendation regarding the main parameters. No performance degradation or mechanical degradation is allow after test. No performance degradation or mechanical degradation is allowed after test No performance degradation or mechanical degradation is allowed at after test No visible degradation of the product, both visual and functional. The unit is tested at room temperature and must be fully operative for the main RF parameters. Under normal condition (room temperature) after the test, the
Stress test
Vibration test
Shock test
IEC 68-2-27
Bump test
IEC 68-2-29
Humidity test
Warehouse test
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 60 / 75
M260 HW spec
Mar.2007
unit must behave in full conformity with the main RF parameters specification. Warehouse test High temperature IEC 68-2-2 Under normal condition (room temperature) after the test, the unit must behave in full conformity with the main RF parameters specification. No visible dust in the visible areas. No more than 50 dust particles in the cabinet of the product. The unit, tested at room temperature must be fully operative. Visual inspection on the discoloration and other degradation effects such as cracks in the material of the unit after the test. Only minor casing degradation is allowed, with a maximum dimension change of 1mm. The unit must remain fully operative and full specification for the main RF parameters. No performance degradation allowed after the test. After the test, visual inspection on the unit. After the test, visual inspection on the unit and inside. After test, visual inspection on the unit. No degradation is allowed on the marking.
Dust test1
Light test 1
Fall test 1
IEC 68-2-32
Electro static discharge test Salt mist test Atmosphere test Marking test
IEC 1000-4-2 or EN 61000-4-2 / A1 Edition 1998 /A2 edition 2001 IEC 68-2-11 Flowing mixed gas corrosion. IEC 68-2-60 EN 60950:2000 standard) (safety tests
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 61 / 75
M260 HW spec
Mar.2007
Digital cellular telecommunications system (phase 2+); Mobile station features (GSM) 02.07 version 8.0.0 Release 1999 Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); Service description, stage 1 (GSM 02.60 version 8.1.0 Release 1999) Technical specification group services and system aspects; Digital cellular telecommunications system (phase 2+); GPRS ; service description ; stage 2 (release 1998) Technical specification group geran; digital cellular telecommunications system (phase 2+); general packet radio service ;overall description of the GPRS radio interface; Stage 2 (release 5) Technical specification group terminals; technical realization of the short message service (SMS) (Release 1998) Technical Specification Group terminals; Technical realization of Cell broadcast service (CBS) (Release 1998) Digital cellular telecommunications system (phase 2+); transmission planning aspects of the speech service in the GSM Public Land Mobile Network (PLMN) system (GSM) 03.50 version 8.1.1 (Release 1999) Technical specification Group GSM/EDGE Radio Access Network; Mobile station base station system (MS - BSS) interface; Data Link (DL) layer specification (release 1999) Technical specification group core network; digital cellular telecommunications system (phase 2+); Mobile radio interface layer 3 specification (release 1998) Technical specification group core network; mobile radio interface layer 3 supplementary services specification; general aspects (release 1998) technical Specification Group GSM/EDGE. Radio (2002-08) Access Network; Radio transmission and reception (Release 5)
v8.1.0
V7.9.0
3GPP TS 03.40 V7.5.0 (2001-12) 3GPP TS 03.41 V7.4.0 (2000-09) ETSI EN 300 V8.1.1(2000-11) 903
3GPP TS V8.2.1(2002-05)
04.06
3GPP TS 04.08 V7.18.0(2002-09) 3GPP TS 04.10 V7.1.0 (2001 - 12) 3GPP TS 45.005 V5.5.0 (2002-08)
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 62 / 75
M260 HW spec
Mar.2007
3GPP TS 45.008 V5.8.0 (2002-08) 3GPP TS 45.010 V5.1.0 (2002-08) 3GPP TS 46.010 V5.0.0 (2002-06) 3GPP TS 46.011 V5.0.0 (2002-06) 3GPP TS 46.012 V5.0.0 (2002-06) 3GPP TS 46.031 V5.0.0 (2002-06) 3GPP TS 46.032 V5.0.0 (2002-06) TS 100 (1999-08) 913V8.0.0
Access control
Technical Specification Group Services and System Aspects; Full rate speech; Transcoding (Release 5) Technical Specification Group Services and System Aspects; Full rate speech; Substitution and muting of lost frames for full rate speech channels (Release 5) Technical Specification Group Services and System Aspects; Full rate speech; Comfort noise aspect for full rate speech traffic channels (Release 5) Technical Specification Group Services and System Aspects; Full rate speech; Discontinuous Transmission (DTX) for full rate speech traffic channels (Release 5) Technical Specification Group Services and System Aspects; Full rate speech; Voice Activity Detector (VAD) for full rate speech traffic channels (Release 5) Digital cellular telecommunications system (Phase 2+); General on Terminal Adaptation Functions (TAF) for Mobile Stations (MS) (GSM 07.01 version 8.0.0 Release 1999) Digital cellular telecommunications system (Phase 2+); General requirements on interworking between the Public Land Mobile Network (PLMN) and the Integrated Services Digital Network (ISDN) or Public Switched Telephone Network (PSTN) (GSM 09.07 version 8.0.0 Release 1999) Technical specification group GSM/EDGE; Radio Access Network; Digital cellular telecommunications system (phase 2+);Mobile station (MS) conformance specification; Part 1: Conformance specification(release 5) technical Specification Group Terminals; Specification of the Subscriber Identity Module Mobile Equipment (SIM - ME) interface (Release 5) Digital cellular telecommunications system (Phase 2); Specification of the 3 Volt Subscriber Identity Module Mobile Equipment (SIM-ME) interface (GSM 11.12
V8.0.0
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 63 / 75
M260 HW spec
Mar.2007
version 4.3.1) GCF-CC (2002-08) NAPRD03 (2002-06) V3.7.1 V2.6.0 Global Certification Forum -Certification Criteria North America PTCRB tests Permanent Reference Document for
6.3
6.3.1 RF safety
6.3.1.1 General
Your GSM terminal
6
standard is spread all over the world. It covers Europe, Asia and some parts of America and Africa. This is the most used telecommunication standard. Your GSM terminal is actually a low power radio transmitter and receiver. It sends out and receives radio frequency energy. When you use your GSM application, the cellular system that handles your calls controls both the radio frequency and the power level of your cellular modem.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 64 / 75
M260 HW spec
Mar.2007
If you are concerned about exposure to RF energy there are things you can do to minimize exposure. Obviously, limiting the duration of your calls will reduce your exposure to RF energy. In addition, you can reduce RF exposure by operating your cellular terminal efficiently by following the below guidelines.
based on M260
6.3.1.3
For your GSM terminal to operate at the lowest power level, consistent with satisfactory call quality: If your terminal has an extendible antenna, extend it fully. Some models allow you to place a call with the antenna retracted. However your GSM terminal operates more efficiently with the antenna fully extended. Do not hold the antenna when the terminal is <IN USE > Holding the antenna affects call quality and may cause the modem to operate at a higher power level than needed.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 65 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 66 / 75
M260 HW spec
Mar.2007
6.3.2.5 Aircraft
Turn your terminal OFF before boarding any aircraft. Use it on the ground only with crew permission. Do not use it in the air. To prevent possible interference with aircraft systems, Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your terminal while the aircraft is on the ground. To prevent interference with cellular systems, local RF regulations prohibit using your modem while airborne.
6.3.2.6 Children
Do not allow children to play with your GSM terminal. It is not a toy. Children could hurt themselves or others (by poking themselves or others in the eye with the antenna, for example). Children could damage the modem, or make calls that increase your modem bills.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 67 / 75
M260 HW spec
Mar.2007
transfer or storage facilities; and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Do not transport or store flammable gas, liquid, or explosives, in the compartment of your vehicle which contains your terminal or accessories. Before using your terminal in a vehicle powered by liquefied petroleum gas (such as propane or butane) ensure that the vehicle complies with the relevant fire and safety regulations of the country in which the vehicle is to be used.
SIMs interface layout: C1,C2,C3,C4 be closed with SIM socket as possible. add ESD protect component between all signals and GND.
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 68 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 69 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 70 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 71 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 72 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 73 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 74 / 75
M260 HW spec
Mar.2007
This document is the sole and exclusive property of Flyfot. .Not to be distributed or divulged without prior written agreement. Page: 75 / 75