Académique Documents
Professionnel Documents
Culture Documents
Preface MS-7583
Preface MS-7583
Safety Instructons
Always read the safety nstructons carefully.
Keep ths Users Manual for future reference.
Keep ths equpment away from humdty.
Lay ths equpment on a relable fat surface before settng t up.
The openngs on the enclosure are for ar convecton hence protects the equpment
from overheatng. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source and adjust properly 110/220V before
connectng the equpment to the power nlet.
Place the power cord such a way that people can not step on t. Do not place any-
thng over the power cord.
Always Unplug the Power Cord before nsertng any add-on card or module.
All cautons and warnngs on the equpment should be noted.
Never pour any lqud nto the openng that could damage or cause electrcal
shock.
If any of the followng stuatons arses, get the equpment checked by servce
personnel:
The power cord or plug s damaged.
Lqud has penetrated nto the equpment.
The equpment has been exposed to mosture.
The equpment does not work well or you can not get t work accordng to Users
Manual.
The equpment has dropped and damaged.
The equpment has obvous sgn of breakage.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED,
STORAGE TEMPERATURE ABOVE 600 C (1400F), IT MAY DAMAGE THE
EQUIPMENT.
CAUTION: Danger of exploson f battery s ncorrectly replaced.
Replace only wth the same or equvalent type recommended by the manufacturer.
:
v
Preface MS-7583 Preface MS-7583
FCC-B Rado Frequency Interference Statement
Ths equpment has been tested and found
to comply wth the lmts for a Class B dg-
tal devce, pursuant to Part 15 of the FCC
Rules. These lmts are desgned to provde
reasonable protecton aganst harmful nter-
ference n a resdental nstallaton. Ths equpment generates, uses and can radate
rado frequency energy and, f not nstalled and used n accordance wth the nstruc-
tons, may cause harmful nterference to rado communcatons. However, there s no
guarantee that nterference wll not occur n a partcular nstallaton. If ths equpment
does cause harmful nterference to rado or televson recepton, whch can be deter-
mned by turnng the equpment of and on, the user s encouraged to try to correct the
nterference by one or more of the measures lsted below.
Reorent or relocate the recevng antenna.
Increase the separaton between the equpment and recever.
Connect the equpment nto an outlet on a crcut dferent from that to whch the
recever s connected.
Consult the dealer or an experenced rado/televson techncan for help.
Notce 1
The changes or modfcatons not expressly approved by the party responsble for com-
plance could vod the users authorty to operate the equpment.
Notce 2
Shelded nterface cables and A.C. power cord, f any, must be used n order to comply
wth the emsson lmts.
VOIR LA NOTICE DINSTALLATION AVANT DE RACCORDER AU RESEAU.
Ths devce comples wth Part 15 of the FCC Rules. Operaton s subject to the follow-
ng two condtons:
ths devce may not cause harmful nterference, and
ths devce must accept any nterference receved, ncludng nterference that may
cause undesred operaton.
1)
2)
Mcro-Star Internatonal
MS-7583
Preface MS-7583
v
Preface MS-7583
WEEE (Waste Electrcal and Electronc Equpment) Statement
ENGLISH
To protect the global envronment and as an envronmentalst, MSI must
remnd you that...
Under the European Unon (EU) Drectve on Waste Electrcal and Elec-
tronc Equpment, Drectve 2002/96/EC, whch takes efect on August 13,
2005, products of electrcal and electronc equpment cannot be dscarded
as muncpal waste anymore and manufacturers of covered electronc equpment wll be
oblgated to take back such products at the end of ther useful lfe. MSI wll comply wth
the product take back requrements at the end of lfe of MSI-branded products that are
sold nto the EU. You can return these products to local collecton ponts.
DEUTSCH
Hnwes von MSI zur Erhaltung und Schutz unserer Umwelt
Gem der Rchtlne 2002/96/EG ber Elektro- und Elektronk-Altgerte drfen Elek-
tro- und Elektronk-Altgerte ncht mehr als kommunale Abflle entsorgt werden. MSI
hat europawet verschedene Sammel- und Recyclngunternehmen beauftragt, de n
de Europsche Unon n Verkehr gebrachten Produkte, am Ende senes Lebenszyklus
zurckzunehmen. Btte entsorgen Se deses Produkt zum gegebenen Zetpunkt aus-
schlesslch an ener lokalen Altgertesammelstelle n Ihrer Nhe.
FRANAIS
En tant qucologste et afn de protger lenvronnement, MSI tent rappeler cec...
Au sujet de la drectve europenne (EU) relatve aux dchets des qupement lec-
trques et lectronques, drectve 2002/96/EC, prenant efet le 13 aot 2005, que les
produts lectrques et lectronques ne peuvent tre dposs dans les dcharges ou
tout smplement ms la poubelle. Les fabrcants de ces qupements seront oblgs de
rcuprer certans produts en fn de ve. MSI prendra en compte cette exgence relatve
au retour des produts en fn de ve au sen de la communaut europenne. Par con-
squent vous pouvez retourner localement ces matrels dans les ponts de collecte.
MSI ,
, ....
()
( WEEE 2002/96/EC), 13
2005 , ,
, ,
. MSI
, MSI
EC, .
.
v
Preface MS-7583 Preface MS-7583
ESPAOL
MSI como empresa comprometda con la proteccn del medo ambente, recomenda:
Bajo la drectva 2002/96/EC de la Unn Europea en matera de desechos y/o equ-
pos electrncos, con fecha de rgor desde el 13 de agosto de 2005, los productos
clasfcados como elctrcos y equpos electrncos no pueden ser depostados en
los contenedores habtuales de su muncpo, los fabrcantes de equpos electrncos,
estn oblgados a hacerse cargo de dchos productos al termno de su perodo de vda.
MSI estar comprometdo con los trmnos de recogda de sus productos venddos en
la Unn Europea al fnal de su perodo de vda. Usted debe depostar estos productos
en el punto lmpo establecdo por el ayuntamento de su localdad o entregar a una
empresa autorzada para la recogda de estos resduos.
NEDERLANDS
Om het mleu te beschermen, wl MSI u eraan hernneren dat.
De rchtljn van de Europese Une (EU) met betrekkng tot Vervulng van Electrsche
en Electronsche producten (2002/96/EC), de op 13 Augustus 2005 n zal gaan kun-
nen net meer beschouwd worden als vervulng. Fabrkanten van dt soort producten
worden verplcht om producten retour te nemen aan het end van hun levenscyclus.
MSI zal overeenkomstg de rchtljn handelen voor de producten de de merknaam MSI
dragen en verkocht zjn n de EU. Deze goederen kunnen geretourneerd worden op
lokale nzamelngspunten.
SRPSKI
Da b zattl prrodnu srednu, kao preduzee koje vod rauna o okoln prrodnoj
sredn, MSI mora da vas podest da
Po Drektv Evropske unje (EU) o odbaenoj ekektronskoj elektrnoj oprem, D-
rektva 2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, prozvod koj spadaju
pod elektronsku elektrnu opremu ne mogu ve bt odbaen kao oban otpad
prozvoa ove opreme be prnuen da uzmu natrag ove prozvode na kraju njhovog
uobajenog veka trajanja. MSI e potovat zahtev o preuzmanju ovakvh prozvoda
kojma je stekao vek trajanja, koj maju MSI oznaku koj su prodat u EU. Ove proz-
vode moete vratt na lokalnm mestma za prkupljanje.
POLSKI
Aby chron nasze rodowsko naturalne oraz jako frma dbajca o ekolog, MSI przy-
pomna, e...
Zgodne z Dyrektyw Un Europejskej (UE) dotyczc odpadw produktw elektry-
cznych elektroncznych (Dyrektywa 2002/96/EC), ktra wchodz w yce 13 serpna
2005, tzw. produkty oraz wyposaene elektryczne elektronczne ne mog by trak-
towane jako mec komunalne, tak wc producenc tych produktw bd zobowzan
do odberana ch w momence gdy produkt jest wycofywany z uyca. MSI wypen
wymagana UE, przyjmujc produkty (sprzedawane na terene Un Europejskej) wy-
cofywane z uyca. Produkty MSI bdze mona zwraca w wyznaczonych punktach
zborczych.
Preface MS-7583
v
Preface MS-7583
TRKE
evrec zellyle blnen MSI dnyada evrey korumak n hatrlatr:
Avrupa Brl (AB) Kararnames Elektrk ve Elektronk Malzeme At, 2002/96/EC
Kararnames altnda 13 Austos 2005 tarhnden tbaren geerl olmak zere, elektrkl
ve elektronk malzemeler der atklar gb pe atlamayacak ve bu elektonk chazlarn
retcler, chazlarn kullanm sreler bttkten sonra rnler ger toplamakla ykml
olacaktr. Avrupa Brlne satlan MSI markal rnlern kullanm sreler bttnde MSI
rnlern ger alnmas ste le brl ersnde olacaktr. rnlernz yerel toplama
noktalarna brakablrsnz.
ESKY
Zle nm na ochran votnho prosted - spolenost MSI upozoruje...
Podle smrnce Evropsk une (EU) o lkvdac elektrckch a elektronckch vrobk
2002/96/EC platn od 13. srpna 2005 je zakzno lkvdovat elektrck a elektronck
vrobky v bnm komunlnm odpadu a vrobc elektronckch vrobk, na kter se
tato smrnce vztahuje, budou povnn odebrat takov vrobky zpt po skonen je-
jch votnost. Spolenost MSI spln poadavky na odebrn vrobk znaky MSI,
prodvanch v zemch EU, po skonen jejch votnost. Tyto vrobky mete odevzdat
v mstnch sbrnch.
MAGYAR
Annak rdekben, hogy krnyezetnket megvdjk, lletve krnyezetvdknt fellpve
az MSI emlkeztet nt, hogy ...
Az Eurpa Un (EU) 2005. augusztus 13-n hatlyba lp, az elektromos s elek-
tronkus berendezsek hulladkarl szl 2002/96/EK rnyelve szernt az elektromos
s elektronkus berendezsek tbb nem kezelhetek lakossg hulladkknt, s az
lyen elektronkus berendezsek gyrt kteless vlnak az lyen termkek vsszav-
telre azok hasznos lettartama vgn. Az MSI betartja a termkvsszavtellel kapc-
solatos kvetelmnyeket az MSI mrkanv alatt az EU-n bell rtkestett termkek
esetben, azok lettartamnak vgn. Az lyen termkeket a legkzelebb gyjthelyre
vhet.
ITALIANO
Per proteggere lambente, MSI, da sempre amca della natura, t rcorda che.
In base alla Drettva dellUnone Europea (EU) sullo Smaltmento de Materal Elettrc
ed Elettronc, Drettva 2002/96/EC n vgore dal 13 Agosto 2005, prodott appartenent
alla categora de Materal Elettrc ed Elettronc non possono p essere elmnat come
rfut muncpal: produttor d dett materal saranno obblgat a rtrare ogn prodotto
alla fne del suo cclo d vta. MSI s adeguer a tale Drettva rtrando tutt prodott
marchat MSI che sono stat vendut allnterno dellUnone Europea alla fne del loro
cclo d vta. possble portare prodott nel p vcno punto d raccolta
v
Preface MS-7583 Preface MS-7583
CONTENTS
Copyrght Notce ............................................................................................
Trademarks ....................................................................................................
Revson Hstory.............................................................................................
Techncal Support..........................................................................................
Safety Instructons .........................................................................................
FCC-B Rado Frequency Interference Statement.......................................... v
WEEE (Waste Electrcal and Electronc Equpment) Statement .................... v
Chapter 1 Gettng Started............................................................................1-1
Manboard Specfcatons ..................................................................................... 1-2
Manboard Layout ................................................................................................ 1-4
Packng Checklst ................................................................................................. 1-5
Chapter 2 Hardware Setup ..........................................................................2-1
Quck Components Gude .................................................................................... 2-2
CPU (Central Processng Unt) ............................................................................ 2-3
Memory ................................................................................................................ 2-7
Power Supply ....................................................................................................... 2-9
Back Panel ......................................................................................................... 2-10
Connectors ......................................................................................................... 2-12
Jumpers ............................................................................................................. 2-20
Button ................................................................................................................. 2-21
Slots ................................................................................................................... 2-22
LED Status Indcators ........................................................................................ 2-28
Chapter 3 BIOS Setup .................................................................................3-1
Enterng Setup ..................................................................................................... 3-2
The Man Menu .................................................................................................... 3-4
Standard CMOS Features .................................................................................... 3-6
Advanced BIOS Features .................................................................................... 3-8
Integrated Perpherals ........................................................................................ 3-10
Power Management Setup ................................................................................. 3-12
H/W Montor ....................................................................................................... 3-15
Green Power ...................................................................................................... 3-16
BIOS Settng Password ...................................................................................... 3-17
Cell Menu ........................................................................................................... 3-19
M-Flash .............................................................................................................. 3-27
Overclockng Profle ........................................................................................... 3-30
Load Fal-Safe/ Optmzed Defaults ................................................................... 3-31
Preface MS-7583
x
Preface MS-7583
Appendx A Realtek Audo .......................................................................... A-1
Installng the Realtek HD Audo Drver .................................................................A-2
Software Confguraton .........................................................................................A-4
Hardware Setup .................................................................................................A-19
Appendx B Control Center ......................................................................... B-1
Actvatng Control Center .....................................................................................B-2
System Informaton ..............................................................................................B-3
Overclockng ........................................................................................................B-5
Green Power ........................................................................................................B-7
Appendx C Intel SATA RAID ..................................................................... C-1
Introducton ......................................................................................................... C-2
BIOS Confguraton ............................................................................................. C-3
Installng Drver ................................................................................................. C-10
Installng Software ............................................................................................. C-12
RAID Mgraton Instructons .............................................................................. C-16
Recovery Volume Creaton ............................................................................... C-23
Degraded RAID Array ....................................................................................... C-26
Appendx D JMcron RAID Introducton ...................................................... D-1
Introducton ......................................................................................................... D-2
JMcron RAID BIOS Utlty ................................................................................... D-3
Deletng RAID set ................................................................................................ D-7
Installng Drver ................................................................................................. D-11
JMcron RAID Confgurer .................................................................................. D-13
1-1-1
Thank you for choosng the P55-GD65 Seres (MS-
7583 v1.X) ATX manboard. The P55-GD65 Seres
manboards are based on Intel
P55 chpsets for optmal
system efcency. Desgned to ft the advanced Intel
Lynnfeld LGA1156 processor, the P55-GD65 Seres
delver a hgh performance and professonal desktop
platform soluton.
Chapter 1
Gettng Started
1-2
Gettng Started MS-7583 Gettng Started MS-7583
MAlNBOARD SPEClFlCATlONS
Processor Support
Intel
Lynnfeld processor n the LGA1156 package
(For the latest nformaton about CPU, please vst http://www.ms.com/ndex.
php?func=cpuform2)
Base Clock
133 MHz
Chpset
Intel
P55 chpset
Memory Support
4 DDR3 DIMMs support DDR3 2133*(OC)/ 2000*(OC) /1600*(OC)/ 1333/ 1066
DRAM (16GB Max)
Supports Dual-Channel mode
*(For more nformaton on compatble components, please vst
http://www.ms.com/ndex.php?func=testreport)
LAN
Supports Dual LAN (10/100/1000) by Realtek
RTL8111DL
IEEE 1394 (optonal)
Chp ntegrated by VIA
VT6315N
Transfer rate s up to 400Mbps
Audo
Chp ntegrated by Realtek
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1-4
Gettng Started MS-7583 Gettng Started MS-7583
P55-GD65 Seres (MS-7583 v1.X) ATX Manboard
MAlNBOARD LAYOUT
J1394_1
(optional)
JAUD1
JCD1
JSPDO1
JTPM1
(optional)
SYSFAN1
Intel
P55
JCOM1
JUSB3 JUSB2 JUSB1
JFP2
JFP1
PCI_E1
PCI_E2
PCI_E3
PCI_E4
PCI_E5
PCI1
PCI2
L
G
A
1
1
5
6
D
I
M
M
2
D
I
M
M
1
D
I
M
M
4
D
I
M
M
3
A
T
X
1
L
E
D
1
L
E
D
3
L
E
D
5
L
E
D
2
L
E
D
4
L
E
D
6
S
Y
S
F
A
N
2
S
Y
S
F
A
N
3
C
P
U
F
A
N
F
D
D
1
B
A
T
T
+
POWER1
I
D
E
1
S
A
T
A
1
_
2
S
A
T
A
7
S
A
T
A
3
_
4
S
A
T
A
5
_
6
J
C
I
1
J
B
A
T
1
Top : mouse
Bottom:keyboard
Top: LAN Jack
Bottom: USB ports
Top: LAN Jack
Bottom: USB ports
Top:
Bottom: USB ports
T:
M:
B:
Line-In
Line-Out
Mic
T:RS-Out
M:CS-Out
B:SS-Out
OC
Genie
Gettng Started MS-7583
1-5
Gettng Started MS-7583
MSI manboard MSI Drver/Utlty DVD SATA Cable (Optonal)
Power Cable USB Bracket (Optonal)
Standard Cable for
IDE Devces
CrossFreX Vdeo Lnk
Cable
PACKlNG CHECKLlST
* The pctures are for reference only and may vary from the packng contents of the
product you purchased.
SLI Vdeo Lnk Card
Back IO Sheld
Users Gude
2-2-1
Ths chapter provdes you wth the nformaton about
hardware setup procedures. Whle dong the nstalla-
ton, be careful n holdng the components and follow the
nstallaton procedures. For some components, f you
nstall n the wrong orentaton, the components wll not
work properly.
Use a grounded wrst strap before handlng computer
components. Statc electrcty may damage the compo-
nents.
Chapter 2
Hardware Setup
2-2
Hardware Setup MS-7583 Hardware Setup MS-7583
OC
Genie
QUlCK COMPONENTS GUlDE
Back Panel,
p.2-10
CPU, p.2-3
CPUFAN, p.2-14
DDR3, p.2-7
Base clock control
buttons, p.2-21
OC Gene, p.2-21
POWER1, p.2-9
POWER2, p.2-21
SYSFAN3, p.2-14
ATX1, p.2-9
V_Check Pont,
p.2-19
IDE1, p.2-12
SYSFAN2, p.2-14
FDD1, p.2-12
SATA1~7, p.2-13
JFP1, JFP2, p.2-15
JUSB1~3, p.2-16
JCOM1, p.2-14
JSPDO1, p.2-17
J1394_1, p.2-15
JCD1, p.2-16
JAUD1, p.2-17
PCI, p.2-27
JCI1, p.2-13
JTPM1, p.2-18
PCIE, p.2-22
SYSFAN1, p.2-14
JBAT1, p.2-20
Hardware Setup MS-7583
2-3
Hardware Setup MS-7583
CPU (CENTRAL PROCESSlNG UNlT)
When you are nstallng the CPU, make sure to nstall the cooler to prevent overheatng.
If you do not have the CPU cooler, consult your dealer before turnng on the computer.
For the latest nformaton about CPU, please vst http://www.ms.com/ndex.
php?func=cpuform2
Important
Overheatng
Overheatng wll serously damage the CPU and system. Always make sure the coolng
fan can work properly to protect the CPU from overheatng. Make sure that you apply
an even layer of thermal paste (or thermal tape) between the CPU and the heatsnk to
enhance heat dsspaton.
Replacng the CPU
Whle replacng the CPU, always turn of the ATX power supply or unplug the power
supplys power cord from the grounded outlet frst to ensure the safety of CPU.
Overclockng
Ths manboard s desgned to support overclockng. However, please make sure your
components are able to tolerate such abnormal settng, whle dong overclockng. Any
attempt to operate beyond product specfcatons s not recommended. We do not guar-
antee the damages or rsks caused by nadequate operaton or beyond product spec-
fcatons.
Introducton to LGA 1156 CPU
The pn-pad sde of LGA 1156 CPU. The surface of LGA 1156 CPU. Remem-
ber to apply some thermal paste on t for
better heat dsperson.
Algnment Key
Yellow trangle s the Pn 1 ndcator
Algnment Key
Yellow trangle s the Pn 1 ndcator
2-4
Hardware Setup MS-7583 Hardware Setup MS-7583
CPU & Cooler Installaton
When you are nstallng the CPU, make sure the CPU has a cooler attached on the top
to prevent overheatng. Meanwhle, do not forget to apply some thermal paste on CPU
before nstallng the heat snk/cooler fan for better heat dsperson.
Follow the steps below to nstall the CPU & cooler correctly. Wrong nstallaton wll
cause the damage of your CPU & manboard.
Open the load level. 1. Lft the load lever up to fully open
poston
2.
The CPU socket has a plastc cap on
t to protect the contact from damage.
Before you nstall CPU, always cover
t to protect the socket pn. Romove
the cap (as the arrow shows).
3. After confrmng the CPU drecton for
correct matng, put down the CPU n
the socket housng frame. Be sure to
grasp on the edge of the CPU base.
Note that the algnment keys are
matched.
4.
Algnment Key
Hardware Setup MS-7583
2-5
Hardware Setup MS-7583
Vsually nspect f the CPU s seated
well nto the socket. If not, take out
the CPU wth pure vertcal moton
and renstall.
5. Engage the load lever whle pressng
down lghtly onto the load plate.
6.
Secure the lever near the hook end
under the retenton tab.
7. Make sure the four hooks are n por-
per poston before you nstall the
cooler.
8.
Important
Confrm f your CPU cooler s frmly nstalled before turnng on your system.
Do not touch the CPU socket pns to avod damagng.
Algnment Key
2-6
Hardware Setup MS-7583 Hardware Setup MS-7583
Manboard
Hook
Important
Read the CPU status n BIOS.
Whenever CPU s not nstalled, always protect your CPU socket pn wth the plastc
cap covered (shown n Fgure 1) to avod damagng.
Manboard photos shown n ths secton are for demonstraton of the CPU/ cooler n-
stallaton only. The appearance of your manboard may vary dependng on the model
you purchase.
Please refer to the documentaton n the CPU fan package for more detals about the
CPU fan nstallaton.
Installed
Empty
2-8
Hardware Setup MS-7583 Hardware Setup MS-7583
Installng Memory Modules
The memory module has only one notch on the center and wll only ft n the rght
orentaton.
Insert the memory module vertcally nto the DIMM slot. Then push t n untl the
golden fnger on the memory module s deeply nserted n the DIMM slot. The plastc
clp at each sde of the DIMM slot wll automatcally close when the memory module
s properly seated.
Manually check f the memory module has been locked n place by the DIMM slot
clps at the sdes.
Notch
Volt
Important
You can barely see the golden fnger f the memory module s properly nserted n the
DIMM slot.
1.
2.
3.
Hardware Setup MS-7583
2-9
Hardware Setup MS-7583
POWER SUPPLY
ATX 24-pn Power Connector: ATX1
Ths connector allows you to connect an ATX 24-pn power supply. To connect the ATX
24-pn power supply, make sure the plug of the power supply s nserted n the proper
orentaton and the pns are algned. Then push down the power supply frmly nto the
connector.
You may use the 20-pn ATX power supply as you lke. If youd lke to use the 20-pn
ATX power supply, please plug your power supply along wth pn 1 & pn 13.
1
3
.
+
3
.
3
V
1
.
+
3
.
3
V
1
4
.
-
1
2
V
2
.
+
3
.
3
V
1
5
.
G
r
o
u
n
d
3
.
G
r
o
u
n
d
1
6
.
P
S
-
O
N
#
4
.
+
5
V
1
7
.
G
r
o
u
n
d
5
.
G
r
o
u
n
d
1
8
.
G
r
o
u
n
d
6
.
+
5
V
1
9
.
G
r
o
u
n
d
7
.
G
r
o
u
n
d
2
2
.
+
5
V
1
0
.
+
1
2
V
2
0
.
R
e
s
8
.
P
W
R
O
K
2
3
.
+
5
V
1
1
.
+
1
2
V
2
1
.
+
5
V
9
.
5
V
S
B
2
4
.
G
r
o
u
n
d
1
2
.
+
3
.
3
V
ATX 8-pn Power Connector: POWER1
Ths connector s used to provde 12V power output to the CPU.
7
.
+
1
2
V
3
.
G
r
o
u
n
d
5
.
+
1
2
V
1
.
G
r
o
u
n
d
8
.
+
1
2
V
4
.
G
r
o
u
n
d
6
.
+
1
2
V
2
.
G
r
o
u
n
d
Important
Make sure that all the connectors are connected to proper ATX power supples to
ensure stable operaton of the manboard.
Power supply of 400 watts (and above) s hghly recommended for system stablty.
ATX 12V power connecton should be greater than 18A.
2-10
Hardware Setup MS-7583 Hardware Setup MS-7583
BACK PANEL
Mouse/Keyboard
The standard PS/2
mouse/keyboard.
Coaxal S/PDIF-Out
Ths SPDIF (Sony & Phlps Dgtal Interconnect Format) connector s provded for dgtal
audo transmsson to external speakers through a coaxal cable.
Optcal S/PDIF-Out
Ths SPDIF (Sony & Phlps Dgtal Interconnect Format) connector s provded for dgtal
audo transmsson to external speakers through an optcal fber cable.
1394 Port (optonal)
The IEEE1394 port on the back panel provdes connecton to IEEE1394 devces.
USB Port
The USB (Unversal Seral Bus) port s for attachng USB devces such as keyboard,
mouse, or other USB-compatble devces.
ESATA/USB Combo Port
The ESATA/USB combo port s for attachng the ESATA external hard drve or USB
devce.
Mouse
(optonal)
1394 Port
USB Port
LAN
Lne-In
Lne-Out
Mc
RS-Out
CS-Out
SS-Out
USB Port ESATA/ USB
Combo Port
USB Port Keyboard
Coaxal
S/PDIF-Out
Optcal
S/PDIF-Out
USB Port
LAN
Hardware Setup MS-7583
2-11
Hardware Setup MS-7583
LAN
The standard RJ-45 LAN jack s for connecton to
the Local Area Network (LAN). You can connect a
network cable to t.
LED Color LED State Condton
Left Yellow Of LAN lnk s not establshed.
On(Steady state) LAN lnk s establshed.
On(brghter & pulsng) The computer s communcatng wth another computer on the LAN.
Rght Green Of 10 Mbts/sec data rate s selected.
On 100 Mbts/sec data rate s selected.
Orange On 1000 Mbts/sec data rate s selected.
Audo Ports
These audo connectors are used for audo devces. It s easy to dferentate between
audo efects accordng to the color of audo jacks.
Lne-In (Blue) - Lne In, s used for external CD player, tape-player or other
audo devces.
Lne-Out (Green) - Lne Out, s a connector for speakers or headphones.
Mc (Pnk) - Mc, s a connector for mcrophones.
RS-Out (Black) - Rear-Surround Out n 4/ 5.1/ 7.1 channel mode.
CS-Out (Orange) - Center/ Subwoofer Out n 5.1/ 7.1 channel mode.
SS-Out (Gray) - Sde-Surround Out 7.1 channel mode.
ATI CrossFreX
TM
(Mult-GPU) Technology
ATI CrossFreX
TM
s the ultmate mult-GPU performance gamng platform. Enablng
game-domnatng power, ATI CrossFreX
TM
technology enables two dscrete graphcs
processors to work together to mprove system performance. ATI CrossFreX
TM
technol-
ogy allows you to expand your systems graphcs capabltes. It allows you the ablty to
scale your systems graphcs horsepower as you need t, supportng two ATI Radeon
TM
HD graphcs cards, makng ths the most scalable gamng platform ever. The manboard
can auto detect the CrossFreX
TM
mode by software, therefore you dont have to enable
the CrossFreX
TM
n BIOS by yourself. The followng detals the CrossFreX
TM
nstalla-
ton.
Install one ATI Radeon
TM
HD graphcs card n frst PCIE x16 slot , then nstall one
ATI Radeon
TM
HD graphcs card n second PCIE x16 slot.
Wth two cards nstalled, an CrossFreX
TM
Vdeo Lnk cable s requred to connect
the golden fngers on the top of these two graphcs cards (refer to the pcture be-
low). Please note that although you have nstalled two graphcs cards, only the
vdeo outputs on the graphcs card nstalled n frst PCIE x16 slot wll work. Hence,
you only need to connect a montor to ths graphcs card.
1.
2.
CrossFreX
TM
Vdeo Lnk cable
2-24
Hardware Setup MS-7583 Hardware Setup MS-7583
When all of the hardware and software has been properly set up and nstalled, re-
boot the system. After enterng the O.S., clck the Catalyst
TM
Control Center con
on the desktop. There s a settng n the Catalyst
TM
Control Center that needs to be
enabled for CrossFreX
TM
to operate. The followng aspect appears n Catalyst
TM
Control Center:
3.
Select the Advanced Vew
from the vew drop menu.
Important
A CrossFreX
TM
system has four possble dsplay modes:
SuperTlng
Scssor Mode
Alternate Frame Renderng
Super Ant-alasng.
for more detals, please consult the graphcs card manual from the manufacturer.
SLI (Scalable Lnk Interface) technology allows two GPUs to run n tandem
wthn a system to acheve up to twce the performance of a sngle graphcs card. To ut-
lze ths technology, the two GPU cards must be connected by an SLI Vdeo Lnk card.
SLI Vdeo Lnk Card
If you ntend to use the SLI mode for better graphcs performance, please refer to the
followng nstructons.
Install two graphcs cards on PCI Express x16 slots. Wth two cards nstalled, an SLI
Vdeo Lnk Card s requred to connect the golden fngers on the top of these two
graphcs cards (refer to the pcture below). Please note that although you have n-
stalled two graphcs cards, only the vdeo outputs on the frst card wll work. Hence,
you only need to connect a montor to the frst PCI Express card.
1.
SLI Vdeo Lnk Card
Important
The photos shown n ths secton are for demonstraton only. The appearance of your
manboard may vary dependng on the model you purchase.
If you ntend to nstall TWO x16 graphcs cards, make sure that these two graphcs
cards are of the same brand and specfcatons.
Make sure that you connect an adequate power supply to the power connector on the
graphcs card to ensure stable operaton of the graphcs card.
2-26
Hardware Setup MS-7583 Hardware Setup MS-7583
Check the box
Important
If you want to remove one graphcs card and qut the SLI functon, make sure the Mul-
tGPU functon s dsabled.
After the hardware nstallaton s completed, restart the system and nstall the NV
SLI drver/utlty. A confguraton panel wll be provded for Mult-GPU control. Check
the Enable mult-GPU box to enable the SLI functon for the onboard graphcs cards
(concernng the detals of mult-GPU settngs, please refer to your graphcs card
manual).
2.
Restart your system and a pop-up message wll show n the system tray confrmng
the Mult-GPU has been enabled.
3.
Hardware Setup MS-7583
2-27
Hardware Setup MS-7583
PCI (Perpheral Component Interconnect) Slot
The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that
comply wth PCI specfcatons.
32-bt PCI Slot
Important
When addng or removng expanson cards, make sure that you unplug the power sup-
ply frst. Meanwhle, read the documentaton for the expanson card to confgure any
necessary hardware or software settngs for the expanson card, such as jumpers,
swtches or BIOS confguraton.
PCI Interrupt Request Routng
The IRQ, acronym of nterrupt request lne and pronounced I-R-Q, are hardware lnes
over whch devces can send nterrupt sgnals to the mcroprocessor. The PCI IRQ pns
are typcally connected to the PCI bus pns as follows:
Order1 Order2 Order3 Order4
PCI Slot1 INT E# INT F# INT G# INT H#
PCI Slot2 INT F# INT G# INT H# INT E#
2-28
Hardware Setup MS-7583
OC
Genie
LED STATUS lNDlCATORS
APS LEDs
These APS (Actve Phase Swtchng) LEDs ndcate the current CPU power phase
mode. Follow the nstructons
below to read.
: ON, : OFF
6 of the LEDs wll lght blue when CPU s n 6 phase power mode.
5 of the LEDs wll lght blue when CPU s n 5 phase power mode.
4 of the LEDs wll lght blue when CPU s n 4 phase power mode.
3 of the LEDs wll lght blue when CPU s n 3 phase power mode.
2 of the LEDs wll lght blue when CPU s n 2 phase power mode.
1 of the LEDs wll lght blue when CPU s n 1 phase power mode.
APS LEDs
2-3-1
Ths chapter provdes nformaton on the BIOS Setup
program and allows you to confgure the system for op-
tmum use.
You may need to run the Setup program when:
An error message appears on the screen durng
the system bootng up, and requests you to run
SETUP.
You want to change the default settngs for cus-
tomzed features.
Chapter 3
BIOS Setup
3-2
BIOS Setup MS-7583 BIOS Setup MS-7583
ENTERlNG SETUP
Power on the computer and the system wll start POST (Power On Self Test) process.
When the message below appears on the screen, press <DEL> key to enter Setup.
Press DEL to enter SETUP
If the message dsappears before you respond and you stll wsh to enter Setup, restart
the system by turnng t OFF and On or pressng the RESET button. You may also re-
start the system by smultaneously pressng <Ctrl>, <Alt>, and <Delete> keys.
Important
The tems under each BIOS category descrbed n ths chapter are under contnuous
update for better system performance. Therefore, the descrpton may be slghtly df-
ferent from the latest BIOS and should be held for reference only.
Upon boot-up, the 1st lne appearng after the memory count s the BIOS verson. It s
usually n the format:
A7583IMS V1.0 062009 where:
1st dgt refers to BIOS maker as A = AMI, W = AWARD, and P = PHOENIX.
2nd - 5th dgt refers to the model number.
6th dgt refers to the chpset as I = Intel, N = NVIDIA, A = AMD and V = VIA.
7th - 8th dgt refers to the customer as MS = all standard customers.
V1.0 refers to the BIOS verson.
062009 refers to the date ths BIOS was released.
3-6
BIOS Setup MS-7583 BIOS Setup MS-7583
STANDARD CMOS FEATURES
The tems n Standard CMOS Features Menu nclude some basc setup tems. Use the
arrow keys to hghlght the tem and then use the <PgUp> or <PgDn> keys to select the
value you want n each tem.
Date (MM:DD:YY)
Ths allows you to set the system to the date that you want (usually the current date).
The format s <day><month> <date> <year>.
[day] Day of the week, from Sun to Sat, determned by BIOS. Read-
only.
[month] The month from Jan. through Dec.
[date] The date from 1 to 31 can be keyed by numerc functon keys.
[year] The year can be adjusted by users.
Tme (HH:MM:SS)
Ths allows you to set the system tme that you want (usually the current tme). The tme
format s <hour> <mnute> <second>.
3-8
BIOS Setup MS-7583 BIOS Setup MS-7583
ADVANCED BlOS FEATURES
Boot Sequence
Press <Enter> to enter the sub-menu.
1st/ 2nd/ 3rd/ --- Boot Devce
These tems allow you to set the frst/ second/ thrd boot devce where BIOS at-
tempts to load the dsk operatng system.
Boot From Other Devce
Settng the opton to [Yes] allows the system to try to boot from other devce, f the
system fals to boot from 1st boot devce.
BIOS Flash Protecton
Ths functon protects the BIOS from accdental corrupton by unauthorzed users or
computer vruses. When enabled, the BIOS data cannot be changed when attempt-
ng to update the BIOS wth a Flash utlty. To successfully update the BIOS, you wll
need to dsable ths Flash BIOS Protecton functon. You should enable ths functon
at all tmes. The only tme when you need to dsable t s when you want to update the
BIOS. After updatng the BIOS, you should mmedately re-enable t to protect t aganst
vruses.
Full Screen Logo Dsplay
Ths tem enables ths system to show the company logo on the boot-up screen. Set-
tngs are:
[Enabled] Shows a stll mage (logo) on the full screen at boot.
[Dsabled] Shows the POST messages at boot.
3-10
BIOS Setup MS-7583 BIOS Setup MS-7583
lNTEGRATED PERlPHERALS
USB Controller
Ths settng allows you to enable/dsable the onboard USB controller.
USB Devce Legacy Support
Select [Enabled] f you need to use a USB-nterfaced devce n the operatng system.
Onboard LAN Controller
Ths settng allows you to enable/dsable the onboard LAN controller.
LAN Opton ROM
Ths tem s used to decde whether to nvoke the Boot ROM of the onboard LAN.
Onboard 2nd LAN Controller
Ths settng allows you to enable/dsable the onboard 2nd LAN controller.
Onboard IEEE1394 Controller (optonal)
Ths tem allows you to enable/dsable the onboard IEEE1394 controller.
Extra RAID/ IDE Controller
Ths tem allows you to enable/dsable the onboard extra RAID/ IDE controller.
HD Audo Controller
Ths settng s used to enable/dsable the onboard audo controller.
3-12
BIOS Setup MS-7583 BIOS Setup MS-7583
POWER MANAGEMENT SETUP
Important
S3-related functons descrbed n ths secton are avalable only when the BIOS sup-
ports S3 sleep mode.
ACPI Functon
Ths tem s to actvate the ACPI (Advanced Confguraton and Power Management
Interface) Functon. If your operatng system s ACPI-aware, such as Wndows 98SE/
2000/ ME/ XP, select [Enabled].
ACPI Standby State
Ths tem specfes the power savng modes for ACPI functon. If your operatng system
supports ACPI, such as Wndows 2000/ XP, you can choose to enter the Standby mode
n S1(POS) or S3(STR) fashon through the settng of ths feld. Settngs are:
[S1] The S1 sleep mode s a low power state. In ths state, no system
context s lost (CPU or chpset) and hardware mantans all sys-
tems context.
[S3] The S3 sleep mode s a lower power state where the n formaton of
system confguraton and open applcatons/fles s saved to man
memory that remans powered whle most other hardware compo-
nents turn of to save energy. The nformaton stored n memory wll
be used to restore the system when a wake up event occurs.
3-14
BIOS Setup MS-7583 BIOS Setup MS-7583
Resume By PCI-E Devce
When set to [Enabled], the feature allows your system to be awakened from the
power savng modes through any event on PCIE devce.
Resume By Onboard LAN
When set to [Enabled], the feature allows your system to be awakened from the
power savng modes through any event on onboard LAN devce.
Resume By RTC Alarm
The feld s used to enable or dsable the feature of bootng up the system on a
scheduled tme/date.
Date/Tme (HH:MM:SS)
If Resume By RTC Alarm s set to [Enabled], the system wll automatcally resume
(boot up) on a specfc date/hour/mnute/second specfed n these felds (usng the
<+> and <-> to select the date & tme settngs). Avalable settngs for each tem
are:
[Date] 01 ~ 31, Every Day
[Tme (HH:MM:SS)] 00 ~ 23 : 00 ~ 59 : 00 ~ 59
3-16
BIOS Setup MS-7583 BIOS Setup MS-7583
GREEN POWER
CPU Phase Control
When set to [Auto], the hardware wll auto adjust the CPU power phase accordng to the
loadng of CPU to reach the best power savng functon.
Manboard LED Control
Ths tem s used to turn on (Auto)/ turn of (Dsabled) the power phase LEDs of the
manboard.
3-18
BIOS Setup MS-7583 BIOS Setup MS-7583
Important
Type the password, up to eght characters n length, and press <Enter>. The password
typed now wll replace any prevously set password. You wll be prompted to confrm the
password. Retype the password and press <Enter>. You may also press <Esc> to abort
the selecton and not enter a password.
To clear a set password, just press <Enter> when you are prompted to enter the pass-
word. A message wll show up confrmng the password wll be dsabled. Once the
password s dsabled, the system wll boot and you can enter Setup wthout enterng
any password.
When a password has been set, you wll be prompted to enter t every tme you try to
enter Setup/ System. Ths prevents an unauthorzed person from changng any part of
your system confguraton.
About Supervsor Password & User Password:
Supervsor password: Can enter and change the settngs of the setup menu.
User password: Can only enter but do not have the rght to change the settngs of the
setup menu.
User Access Level
Ths tem s used to lmt the user access level.
Passwrod Check
Ths specfes the type of BIOS password protecton that s mplemented. Settngs are
descrbed below:
Opton Descrpton
[BIOS] The password prompt appears only when end users try to run Setup.
[System] A password prompt appears every tme when the computer s powered
on or when end users try to run Setup.
Save Supervsor Password to
Ths tem s used to assgn a place to save the supervsor password.
3-20
BIOS Setup MS-7583 BIOS Setup MS-7583
CPU Specfcatons
Press <Enter> to enter the sub-menu and the followng screen appears. Ths submenu
shows the nformaton of nstalled CPU.
CPU Technology Support
Press <Enter> to enter the sub-menu. In ths sub-menu, t shows the nstalled CPU
technologes. Read only.
CPU Feature
Press <Enter> to enter the sub-menu and the followng screen appears:
Intel EIST
The Enhanced Intel SpeedStep technology allows you to set the performance level
of the mcroprocessor whether the computer s runnng on battery or AC power. Ths
feld wll appear after you nstalled the CPU whch supports speedstep technology.
Intel C-STATE
C-state s a power management state that sgnfcantly reduces the power of the
processor durng dle. Ths feld wll appear after you nstalled the CPU whch sup-
ports c-state technology.
3-22
BIOS Setup MS-7583 BIOS Setup MS-7583
Adjust CPU Base Frequency (MHz)
Ths tem allows you to set the CPU Base clock (n MHz). You may overclock the CPU
by adjustng ths value. Please note the overclockng behavor s not guaranteed.
OC Steppng
Ths tem wll be enabled after you set the overclockng frequency n the Adjust CPU
Base Frequency (MHz). And the followng tems wll appear. Ths tems wll help the
system to overclock step by step after system bootng up.
Start OC Steppng From (MHz)
Ths tem s used to set the ntal base clock. The system wll boot wth the ntal base
clock, and start to overclock from ntal base clock to set base clock that you set n
Adjust CPU Base Frequency (MHz) step by step.
OC Step
Ths tem s used to set how many steps for base colck overclockng.
OC Step Count Tmer
Ths tem s used to set the bufer tme for every step.
Adjust CPU Rato
Ths tem allows you to adjust the CPU rato. Settng to [Startup] enables the CPU run-
nng at the fastest speed whch s detected by system.
Adjusted CPU Frequency (MHz)
It shows the adjusted CPU frequency (Base clock x Rato). Read-only.
OC Gene
Ths tem s used to enable/ dsable the OC Gene functon.
Memory-Z
Press <Enter> to enter the sub-menu and the followng screen appears.
DIMM1~4 Memory SPD Informaton
Press <Enter> to enter the sub-menu. The sub-menu dsplays the nformatons of
nstalled memory.
Current DRAM Channel1~4 Tmng
It shows the nstalled DRAM Tmng. Read-only.
DRAM Tmng Mode
Select whether DRAM tmng s controlled by the SPD (Seral Presence Detect) EE-
PROM on the DRAM module. Settng to [Auto] enables DRAM tmngs and the followng
Advance DRAM Confguraton sub-menu to be determned by BIOS based on the con-
fguratons on the SPD. Selectng [Manual] allows users to confgure the DRAM tmngs
and the followng related Advance DRAM Confguraton sub-menu manually.
3-24
BIOS Setup MS-7583 BIOS Setup MS-7583
Channel 1/ Channel2 Advanced Memory Settng
Settng to [Auto] enables the advance memory tmng automatcally to be determned
by BIOS. Settng to [Manual] allows you to set the followng advanced memory tm-
ngs.
Extreme Memory Profle (X.M.P.)
Ths tem s used to enable/dsable the Intel Extreme Memory Profle (X.M.P.). For fur-
ther nformaton please refer to Intels ofcal webste.
Memory Rato
Ths tem allows you to set the memory multpler.
Adjusted DRAM Frequency (MHz)
It shows the adjusted DRAM frequency. Read-only.
QPI Rato
Ths tem allows you to set the QPI multpler.
Adjusted QPI Frequency (MHz)
It shows the adjusted QPI frequency. Read-only.
ClockGen Tuner
Press <Enter> to enter the sub-menu and the followng screen appears.
CPU Ampltude Control/ PCI Express Ampltude Control
These tems are used to select the CPU/ PCI Express clock ampltude.
Adjust PCI Frequency (MHz)
Ths feld allows you to select the PCI frequency (n MHz).
Adjust PCI-E Frequency (MHz)
Ths feld allows you to select the PCIE frequency (n MHz).
Auto Dsable DRAM/PCI Frequency
When set to [Enabled], the system wll remove (turn of) clocks from empty DIMM and
PCI slots to mnmze the electromagnetc nterference (EMI).
3-26
BIOS Setup MS-7583 BIOS Setup MS-7583
Important
Faled Overclockng Resoluton
Ths manboard supports overclockng greatly. However, please make sure your pe-
rpherals and components are bearable for some specal settngs. Any operaton that
exceeds product specfcaton s not recommended. Any rsk or damge resultng from
mproper operaton wll not be under our product warranty.
Two ways to save your system from faled overclockng...
Reboot
Press the Power button to reboot the system three tmes. Please note that, to avod
electrc current to afect other devces or components, we suggest an nterval of more
than 10 seconds among the reboot actons.
At the fourth reboot, BIOS wll determne that the prevous overclockng s faled and
restore the default settngs automatcally. Please press any key to boot the system
normally when the followng message appears on screen.
Warnng !!! The prevous overclockng had faled,
and system wll restore ts defaults settng,
Press any key to contnue.......
Clear CMOS
Please refer to Chapter 2 for more nformaton about how to clear CMOS data.
3-28
BIOS Setup MS-7583 BIOS Setup MS-7583
Important
Please refer to the block dagram below about the M-Flash functon.
Due to the specal desgn of some graphcs cards wll cause dark screen durng M-
fash operaton, and you may refer the beeps from the system to confrm the current
M-fash process.
3-30
BIOS Setup MS-7583 BIOS Setup MS-7583
OVERCLOCKlNG PROFlLE
Overclockng Profle 1/ 2/ 3/ 4/ 5/ 6
These tems are used to save the currect settngs to selected profle, and they are also
used to load the settngs from the selected profle.
OC Retry Count
When the overclockng s faled, settng ths tem to [1, 3, 5] wll allow system to reboot 1/
3/ 5 tmes wth the overclockng confguraton. If the overclockng was faled every tme,
the system wll restore the defaults.
XP
For Wndows
XP, you must nstall Wndows
XP Servce Pack3 or later before nstallng
the drver.
The followng llustratons are based on Wndows
XP envronment and could look
slghtly dferent f you nstall the drvers n dferent operatng systems.
Insert the applcaton DVD nto the DVD-ROM drve. The setup screen wll automat-
cally appear.
Clck Realtek HD Audo Drvers button.
1.
2.
Important
The HD Audo Confguraton software utlty s under contnuous update to enhance au-
do applcatons. Hence, the program screens shown here n ths secton may be slghtly
dferent from the latest software utlty and shall be held for reference only.
Clck here
A-3
MS-7583
Clck Next to nstall the Realtek Hgh Defnton Audo Drver. 3.
Clck Fnsh to restart the system. 4.
Clck here
Clck here
Select ths opton
Clck here
A-4
Realtek Audo
SOFTWARE CONFlGURATlON
After nstallng the audo drver, you are able to use the 2-, 4-, 6- or 8- channel audo
feature now. Clck the audo con from the system tray at the lower-rght corner of the
screen to actvate the HD Audo Confguraton. It s also avalable to enable the audo
drver by clckng the Realtek HD Audo Manager from the Control Panel.
Double clck
A-5
MS-7583
Sound Efect
Here you can select a sound efect you lke from the Envronment lst.
Envronment Smulaton
You wll be able to enjoy dferent sound experence by pullng down the arrow, totally
23 knds of sound efect wll be shown for selecton. Realtek HD Audo Sound Manager
also provdes fve popular settngs Stone Corrdor, Bathroom, Sewer ppe, Arena
and Audtorum for quck enjoyment.
You may choose the provded sound efects, and the equalzer wll adjust automatcally.
If you lke, you may also load an equalzer settng or make an new equalzer settng to
save as an new one by usng the Load EQ Settng and Save Preset button, clck
Reset EQ Settng button to use the default value, or clck Delete EQ Settng button
to remove a preset EQ settng.
There are also other pre-set equalzer models for you to choose by clckng Others
under the Equalzer part.
A-6
Realtek Audo
Equalzer Selecton
Equalzer frees users from default settngs; users may create ther owned preferred
settngs by utlzng ths tool.
10 bands of equalzer, rangng from 100Hz to 16KHz.
Save
The settngs are saved perma-
nently for future use
Load
Whenever you would lke to
use preload settngs, smply
clck ths, the whole lst wll be
shown for your selecton.
Enable / Dsable
To dsable, you can temporar-
ly stop the sound efect wthout
losng the settngs
Reset
10 bands of equalzer would go
back to the default settng
Delete
To delete the pre-saved settngs whch are created from prevous steps.
A-7
MS-7583
Frequently Used Equalzer Settng
Realtek recognzes the needs that you mght have. By leveragng our long experence at
audo feld, Realtek HD Audo Sound Manager provdes you certan optmzed equalzer
settngs that are frequently used for your quck enjoyment.
[How to Use It]
Other than the buttons Pop, Lve, Club & Rock shown on the page, to pull down
the arrow n Others you wll fnd more optmzed settngs avalable to you.
Karaoke Mode
Karaoke mode brngs Karaoke fun back home. Smply usng the musc you usually play,
Karaoke mode can help you elmnate the vocal of the song or adjust the key to accom-
modate your range.
Vocal Cancellaton: Sngle clck on Voce Cancellaton the vocal of the song would
be elmnated, whle the background musc s stll n place, and you can be that
snger!
Key Adjustment: Usng Up / Down Arrow to fnd a key whch better fts your vocal
range.
1.
2.
Rase the key
Lower the key
Remove the
human voce
A-8
Realtek Audo
Mxer
In the Mxer part, you may adjust the volumes of the rear and front panels ndvdually.
Adjust Volume
You can adjust the volume of the speakers that you pluged n front or rear panel by
select the Realtek HD Audo rear output or Realtek HD Audo front output tems.
Important
Before set up, please make sure the playback devces are well plugged n the jacks on
the rear or front panel. The Realtek HD Audo front output tem wll appear after you
plugng the speakers nto the jacks on the front panel.
Mult-Stream Functon
Realtek audo supports an outstandng feature called Mult-Stream, whch means you
may play dferent audo sources smultaneously and let them output respectvely from
the ndcated real panel or front panel. Ths feature s very helpful when 2 people are
usng the same computer together for dferent purposes.
Clck the button and the Mxer ToolBox menu wll appear. Then check the Enable
playback mult-streamng and clck OK to save the setup.
Important
You have to plug audo devce nto the jacks on the rear and front panel frst before en-
able the mult-stream functon.
A-9
MS-7583
When you are playng the frst audo source (for example: use Wndows Meda Player
to play DVD/VCD), the output wll be played from the rear panel, whch s the default
settng.
Then you must to select the Realtek HD Audo 2nd output from the scroll lst frst, and
use a dferent program to play the second audo source (for example: use Wnamp to
play MP3 fles). You wll fnd that the second audo source (MP3 musc) wll come out
from the Lne-Out audo jack of Front Panel.
A-10
Realtek Audo
Playback control
Playback devce
Ths functon s to let you freely decde whch ports
to output the sound. And ths s essental when mult-
streamng playback enabled.
- Realtek HD Audo Rear Output
- Realtek HD Audo Front Output
Tool Mute
Mute
You may choose to mute sngle or multple volume controls or to completely mute sound
output.
Tool
- Show the followng volume controls
Ths s to let you freely decde whch volume control tems to be dsplayed.
- Advanced controls
- Enable playback mult-streamng
Wth ths functon, you wll be able to have an audo chat wth your frends va headphone
(stream 1 from front panel) whle stll has musc (stream 2 from back panel) n play. At
any gven perod, you can have maxmum 2 streams operatng smultaneously.
A-11
MS-7583
Recordng control
Recordng devce
-Back Lne n/ Mc, Front Ln n
-Realtek HD Audo Input
Tool Mute
Mute
You may choose to mute sngle or multple volume controls or to completely mute sound
nput.
Tool
- Show the followng volume controls
Ths s to let you freely decde whch volume control tems to be dsplayed.
- Enable recordng mult-streamng
Important
Realtek audo allows you to record the CD, Lne, Mc and Stereo Mx channels smul-
taneously, frees you from mxng eforts. At any gven perod, you may choose 1 of the
followng 4 channels to record.
A-12
Realtek Audo
Audo I/O
In ths tab, you can easly confgure your mult-channel audo functon and speakers.
You can choose a desred mult-channel operaton here.
Headphone for the common headphone
2CH Speaker for Stereo-Speaker Output
4CH Speaker for 4-Speaker Output
6CH Speaker for 5.1-Speaker Output
8CH Speaker for 7.1-Speaker Output
Speaker Confguraton:
Plug the speakers n the correspondng jack.
Dalogue connected devce wll pop up for your selecton. Please select the devce
you have plugged n.
- If the devce s beng plugged nto the correct jack, you wll be able to fnd the con
besde the jack changed to the one that s same as your devce.
- If not correct, Realtek HD Audo Manager wll gude you to plug the devce nto the
correct jack.
1.
2.
A-13
MS-7583
Connector Settngs
Clck to access connector settngs.
Dsable front panel jack detecton (optonal)
Jack detecton functon only works wth HD audo front panel. Please check f front jacks
on your system are so-called AC97 jacks. If so, please check ths tem to dsable front
panel jack detecton.
Mute rear panel output when front headphone plugged n.
Enable auto popup dalogue, when devce has been plugged n
Once ths tem checked, the dalog Connected devce would automatcally pop up
when devce plugged n.
A-14
Realtek Audo
S/PDIF
Short for Sony/Phlps Dgtal Interface, a standard audo fle transfer format. S/PDIF al-
lows the transfer of dgtal audo sgnals from one devce to another wthout havng to be
converted frst to an analog format. Mantanng the vablty of a dgtal sgnal prevents
the qualty of the sgnal from degradng when t s converted to analog.
Output Samplng Rate
44.1KHz: Ths s recommend whle playng CD.
48KHz: Ths s recommended whle playng DVD or Dolby.
96KHz: Ths s recommended whle playng DVD-Audo.
192KHz: Ths s recommended whle playng Hgh qualty Audo.
Output Source
Output dgtal audo source: The dgtal audo format (such as .wav, .mp3,.md etc) wll
come out through S/PDIF-Out.
S/PDIF-n to S/PDIF -out pass though mode: The data from S/PDIF-In can be real-tme
played from S/PDIF-Out.
A-15
MS-7583
Test Speakers
You can select the speaker by clckng t to test ts functonalty. The one you select
wll lght up and make testng sound. If any speaker fals to make sound, then check
whether the cable s nserted frmly to the connector or replace the bad speakers wth
good ones. Or you may clck the auto test button to test the sounds of each speaker
automatcally.
Center
Front Rght
Sde Rght
Subwoofer
Rear Rght
Front Left
Sde Left
Rear Left
A-16
Realtek Audo
Mcrophone
In ths tab you may set the functon of the mcrophone. Select the Nose Suppresson
to remove the possble nose durng recordng, or select Acoustc Echo Cancellaton to
cancel the acoustc echo durng recordng.
Acoustc Echo Cancellaton prevents playback sound from beng recorded by mcro-
phone together wth your sound. For example, you mght have chance to use VOIP
functon through Internet wth your frends. The voce of your frend wll come out from
speakers (playback). However, the voce of your frend mght also be recorded nto your
mcrophone then go back to your frend through Internet. In that case, your frend wll
hear hs/her own voce agan. Wth AEC (Acoustc Echo Cancellaton) enabled at your
sde, your frend can enjoy the beneft wth less echo.
A-17
MS-7583
3D Audo Demo
In ths tab you may adjust your 3D postonal audo before playng 3D audo applcatons
lke gamng. You may also select dferent envronment to choose the most sutable
envronment you lke.
A-18
Realtek Audo
Informaton
In ths tab t provdes some nformaton about ths HD Audo Confguraton utlty, nclud-
ng Audo Drver Verson, DrectX Verson, Audo Controller & Audo Codec. You may
also select the language of ths utlty by choosng from the Language lst.
Also there s a selecton Show con n system tray. Swtch t on and an con wll show
n the system tray. Rght-clck on the con and the Audo Accessores dalogue box wll
appear whch provdes several multmeda features for you to take advantage of.
A-19
MS-7583
HARDWARE SETUP
Connectng the Speakers
When you have set the Mult-Channel Audo Functon mode properly n the software
utlty, connect your speakers to the correct phone jacks n accordance wth the settng
n software utlty.
2-Channel Mode for Stereo-Speaker Output
Lne In
Lne Out (Front channels)
MIC
No functon
No functon
No functon
1]
2]
3]
4]
5]
6]
A-20
Realtek Audo
4-Channel Mode for Stereo-Speaker Output
Lne In
Lne Out (Front channels)
MIC
Lne Out (Rear channels)
No functon
No functon
1]
2]
3]
4]
5]
6]
A-21
MS-7583
6-Channel Mode for Stereo-Speaker Output
Lne In
Lne Out (Front channels)
MIC
Lne Out (Rear channels)
Lne Out (Center and Subwoofer channel)
No functon
1]
2]
3]
4]
5]
6]
A-22
Realtek Audo
8-Channel Mode for Stereo-Speaker Output
Lne In
Lne Out (Front channels)
MIC
Lne Out (Rear channels)
Lne Out (Center and Subwoofer channel)
Lne Out (Sde channels)
Important
To enable 7.1 channel audo-out functon on Wndows Vsta operatng system, you have
to nstall the Realtek Audo Drver. Or, the manboard wll support 5.1 channel audo-out
only.
1]
2]
3]
4]
5]
6]
B-B-1
Control Center, the most useful and powerful utlty that
MSI has spent much research and eforts to develop,
helps users to montor or confgure the hardware status
of MSI Manboard n wndows, such as CPU clock, volt-
age, fan speed and temperature.
Before you nstall the Control Center, please make sure
the system has meet the followng requrements:
256MB system memory.
DVD-ROM drve for software nstallaton.
Operaton system: Wndows XP or up.
1.
2.
3.
Appendx B
Control Center
B-2
Control Center MS-7583 Control Center MS-7583
ACTlVATlNG CONTROL CENTER
Once you have your Control Center nstalled (locate the setup source fle n the setup
DVD accompanyng wth your manboard, path: Utlty --> MSI Utlty --> Control Center),
t wll have a short cut con on the desktop, and a short cut path n your Start-up menu.
You may double-clck on each con to actvate Control Center.
short-cut con on the desktop
short-cut path n the start-up menu
(path: Start-->Programs-->MSI-->Control Center--
>Control Center)
Control Center MS-7583
B-3
Control Center MS-7583
SYSTEM lNFORMATlON
There are three optons for you to select n the System Informaton screen, you can
read the manboard/ CPU/ memory nformaton by clckng ther respectve name.
Manboard
Clck Manboard to read the nformaton of manboard, manboard BIOS, audo, LAN
and nstalled graphcs card.
Important
The pctures n ths appendx are for reference only and may vary from the product you
purchased. Please refer to the appearance of your system for detaled nformaton.
B-4
Control Center MS-7583 Control Center MS-7583
CPU
Clck CPU to read the nformaton of CPU.
Memory
Clck Memory to read the nformaton of each memory DIMM slot. You can select a
DIMM slot you want to read by clckng arrow button.
Clck ths arrow button to
select the DIMM slot.
Control Center MS-7583
B-5
Control Center MS-7583
OVERCLOCKlNG
In overclockng, you can select the Default/ Cnema/ Game/ Coolng settng for system
to reach the optmum and stable performance. Or you can confgure the advanced
DRAM settng for system to meet the strct demands of hgh efcency and hgh over-
clockng ablty.
Basc
In the Basc, t provdes one default (Default) menu and three common (Coolng/ Cn-
ema/ Game) menus for dferent envronments. You can adjust the CPU/ memory pa-
rameters and the mnmum fan speed separately for each menu. After adjustng, please
clck the Apply button to execute the confgured settng. Or you can clck the Save
button to save the adjustments for future use.
Important
Every tme you turn-of the system, the settngs wll be restored to the factory default. If
you want to use the saved settngs, you have to load t every tme by clckng the Load
button.
B-6
Control Center MS-7583 Control Center MS-7583
Advanced
In Advanced menu, you can adjust the advanced DRAM tmng settngs. After adjustng,
please clck the Apply button to execute the confgured settng. Or you can clck the
Save button to save the adjustments for future use.
Important
Every tme you turn-of the system, the settngs wll be restored to the factory default. If
you want to use the saved settngs, you have to load t every tme by clckng the Load
button.
Control Center MS-7583
B-7
Control Center MS-7583
GREEN POWER
Green Power s an energy savng technology wth unque functon that control power
supply wth auto phase swtchng (Actve Phase Swtchng) for CPU and components.
Helpng you save power,money,and our Earth!
Basc
In the Basc menu, t provdes two settngs for you to experence dferent power sav-
ng perfrmance. These settngs (Optmze/ Max Power Savng) n Basc menu are not
adjustable.
B-8
Control Center MS-7583 Control Center MS-7583
Advanced
In the Advanced menu, you can adjust the CPU power phase, fan speed, and set the
LEDs to lght or not.
Manboard
In the Manboard, t provdes two power savng modes for you to adjust by shftng the
gear. And then, you can clck the Apply button to execute the adjustments. Or you can
clck the Save button to save the adjustments for future use.
shft the gear to
the settng that you
lke.
Important
Every tme you turn-of the system, the settngs wll be restored to the factory default. If
you want to use the saved settngs, you have to load t every tme by clckng the Load
button.
C-C-1
Ths appendx wll assst users n confgurng and en-
ablng RAID functonalty on platforms
Appendx C
Intel SATA RAID
C-2
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
lNTRODUCTlON
The manboard comes wth the Intel RAID controller that allows you to confgure SATA
hard drves as RAID sets.
SATA hard drves delver blsterng transfer speeds up to 3 Gb/s. Seral ATA uses long,
thn cables, makng t easer to connect your drve and mprovng the arfow nsde your
PC. The most outstandng features are:
Supports 3 Gb/s transfers wth CRC error checkng.
Supports Hot-plug-n-play feature.
Data handlng optmzatons ncludng tagged command queung, elevator seek and
packet chan command.
Intel
RAID controller ofers RAID level 0 (Strpng), RAID level 1 (Mrrorng and Duplex-
ng), RAID level 5 (Block Interleaved Dstrbuted Party), RAID level 10 (A Strpe of Mr-
rors) , Intel
Martx Storage Technology and Intel
Rapd Recover Technology.
RAID 0 breaks the data nto blocks whch are wrtten to separate hard drves. Spread-
ng the hard drve I/O load across ndependent channels greatly mproves I/O perfor-
mance.
RAID 1 provdes data redundancy by mrrorng data between the hard drves and pro-
vdes enhanced read performance.
RAID 5 Provdes data strpng at the byte level and also strpe error correcton nforma-
ton. Ths results n excellent performance and good fault tolerance. Level 5 s one of the
most popular mplementatons of RAID.
RAID 10 Not one of the orgnal RAID levels, multple RAID 1 mrrors are created, and a
RAID 0 strpe s created over these.
Intel
Matrx RAID Technology s the advanced ablty for two RAID volumes to share the
combned space of two hard drves beng used n unson.
Intel
Rapd Recover Technology utlzes RAID 1 functonalty to copy data from a des-
gnated Master drve to a desgnated Recovery drve. The sze of the Master drve must
be less than or equal to the sze of the Recovery drve. When a Recovery volume s
created, complete capacty of the Master drve wll be used as the Master volume. Only
one Recovery Volume can exst on a system. There are 2 methods of updatng the
data on the Master to the Recovery drve. They are Contnuous Update Polcy and On
Request Update Polcy.
Important
The least number of hard drves for RAID 0, RAID 1, Recovery or Matrx mode s 2. The
least number of hard drves for RAID 10 mode s 4. And the least number of hard drves
for RAID 5 mode s 3.
All the nformaton/ volumes/ pctures lsted n your system mght dfer from the llustra-
tons n ths appendx.
1.
2.
3.
Intel SATA RAID MS-7583
C-3
Intel SATA RAID MS-7583
BlOS CONFlGURATlON
The Intel Matrx Storage Manager Opton ROM should be ntegrated wth the system
BIOS on all motherboards wth a supported Intel chpset. The Intel Matrx Stroage Man-
ager Opton ROM s the Intel RAID mplementaton and provdes BIOS and DOS dsk
servces. Please use <Ctrl> + <I> keys to enter the Intel
1.
2.
Intel SATA RAID MS-7583
C-5
Intel SATA RAID MS-7583
In the Dsk feld, press <Enter> key and the followng screen appears. Use <Space>
key to select the dsks you want to create for the RAID volume, then clck <Enter>
key to fnsh selecton.
3.
Then select the strp value for the RAID array by usng the upper arrow or
down arrow keys to scroll through the avalable values, and pressng the
<Enter> key to select and advance to the next feld. The avalable values
range from 4KB to 128 KB n power of 2 ncrements. The strp value should
be chosen based on the planned drve usage. Here are some typcal values:
RAID0 -128KB / RAID10 - 64KB / RAID5 - 64KB.
Then select the capacty of the volume n the Capacty feld. The default value s the
maxmum volume capacty of the selected dsks.
4.
5.
C-6
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
Important
Snce you want to create two volumes (Intel Matrx RAID Technology), ths default sze
(maxmum) needs to be reduced. Type n a new sze for the frst volume. As an ex-
ample: f you want the frst volume to span the frst half of the two dsks, re-type the sze
to be half of what s shown by default. The second volume, when created, wll automat-
cally span the remander of two hard drves.
Then the followng screen appears for you to confrm f you are sure to create the
RAID volume. Press <Y> to contnue.
6.
Then the followng screen appears to ndcate that the creaton s fnshed. 7.
Intel SATA RAID MS-7583
C-7
Intel SATA RAID MS-7583
Delete RAID Volume
Here you can delete the RAID volume, but please be noted that all data on RAID
drves wll be lost.
Important
If your system currently boots to RAID and you delete the RAID volume n the Intel RAID
Opton ROM, your system wll become unbootable.
Select opton 2 Delete RAID Volume from the man menu wndow and press <Enter>
key to select a RAID volume for deleton. Then press <Delete> key to delete the
selected RAID volume. The followng screen appears.
Press <Y> key to accept the volume deleton.
C-8
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
Reset Dsks to Non-RAID
Select opton 3 Reset Dsks to Non-RAID and press <Enter> to delete the RAID
volume and remove any RAID structures from the drves. The followng screen
appears:
Press <Y> key to accept the selecton.
Important
You wll lose all data on the RAID drves and any nternal RAID structures when you
perform ths operaton.
Possble reasons to Reset Dsks to Non-RAID could nclude ssues such as ncom-
patble RAID confguratons or a faled volume or faled dsk.
C-10
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
Important
Please follow the nstructon below to make an Intel
lNSTALLlNG DRlVER
Install Drver n Wndows Vsta / XP
New Wndows Vsta / XP Installaton
The followng detals the nstallaton of the drvers whle nstallng operatng system.
When you start nstallng Wndows XP, you may encounter a message statng,
Setup could not determne the type of one or more mass storage devces nstalled
n your system. If ths s the case, then you are already n the rght place and are
ready to supply the drver. If ths s not the case, then press F6 when prompted at
the begnnng of Wndows setup.
Press the S key to select Specfy Addtonal Devce.
You should be prompted to nsert a foppy dsk contanng the Intel
RAID drver
nto the A: drve.
Note: For Wndows XP, you can use the USB foppy drve only.
For Wndows Vsta you can use CD/ DVD/ USB drve.
1.
2.
3.
For Wndows Vsta:
Durng the Operatng system nstallaton, after selectng the locaton to nstall Vsta
clck on Load Drver button to nstall a thrd party SCSI or RAID drver.
When prompted, nsert the foppy dsk or meda (CD/DVD or USB) you created n
step 3 and press Enter.
You should be shown a lst of avalable SCSI Adapters.
Select the approprate Intel RAID controller and press ENTER.
The next screen should confrm that you have selected the Intel
RAID controller.
Press ENTER agan to contnue.
You have successfully nstalled the Intel
1.
2.
3.
4.
1.
2.
3.
C-12
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
lNSTALLlNG SOFTWARE
Install Intel Matrx Storage Console
The Intel Applcaton Accelerator RAID Edton drver may be used to operate the hard
drve from whch the system s bootng or a hard drve that contans mportant data. For
ths reason, you cannot remove or un-nstall ths drver from the system after nstallaton;
however, you wll have the ablty to un-nstall all other non-drver components.
Insert the MSI DVD and clck on the RAID block, and then choose INTEL RAID Drvers
to nstall the software.
Clck on ths tem
Choose ths tem
Intel SATA RAID MS-7583
C-13
Intel SATA RAID MS-7583
The InstallSheld Wzard wll begn automatcally for nstallaton showed as followng:
Clck on the Next button to proceed the nstallaton n the welcomng wndow.
C-14
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
The wndow shows the components to be nstalled. Clck Next button to contnue.
After readng the lcense agreement n the followng wndow, clck Yes button to con-
tnue.
Intel SATA RAID MS-7583
C-15
Intel SATA RAID MS-7583
The followng wndow appears to show the Readme Fle Informaton. It shows the sys-
tem requrements and nstallaton nformaton.
Once the nstallaton s complete, the followng wndow appears.
C-16
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
RAlD MlGRATlON lNSTRUCTlONS
The Intel Matrx Storage Console ofers the fexblty to upgrade from a sngle Seral
ATA (SATA) hard drve to RAID confguraton when an addtonal SATA hard drve s
added to the system. Ths process wll create a new RAID volume from an exstng
dsk. However, several mportant steps must be followed at the tme the system s frst
confgured n order to take advantage of RAID when upgradng to a second SATA hard
drve:
BIOS must be confgured for RAID before nstallng Wndows on the sngle SATA
hard drve. Refer to BIOS secton properly settng.
Install the Intel Applcaton Accelerator RAID Drver durng Wndows Setup. Refer to
Installng Software for nstructons on nstallng the drver durng Wndows Setup.
Install the Intel Matrx Storage Console after the operatng system s nstalled.
To create a volume from an exstng dsk, complete the followng steps:
Important
A Create from Exstng Dsk operaton wll delete all exstng data from the added dsk
and the data cannot be recovered. It s crtcal to backup all mportant data on the added
dsk before proceedng. However, durng the mgraton process, the data on the source
dsk s preserved.
After the Intel Matrx Storage Console has been successfully nstalled and the sys-
tem has rebooted, clck on the Intel Applcaton Accelerator shortcut lnk (Start --> All
Programs --> Intel Matrx Storage Manager --> Intel Matrx Storage Console) and the
followng wndow wll appear:
1.
2.
3.
Intel SATA RAID MS-7583
C-17
Intel SATA RAID MS-7583
Create RAID Volume from Exstng Dsk
To create a RAID volume from an exstng dsk, choose Acton --> Create RAID Volume
from Exstng Hard Drve.
The Create RAID Volume from Exstng Hard Drve Wzard pops up to lead you for the
followng procedure. Clck Next to contnue.
C-18
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
(1) Confgure Volume
Here you can confgure the new RAID volume by enterng the volume name, selectng
the RAID level and strp sze.
RAID Volume Name:
A desred RAID volume name needs to be typed n where the Volume_0000 text
currently appears above. The RAID volume name has a maxmum lmt of 16 char-
acters. The RAID volume name must also be n Englsh alphanumerc ASCII char-
acters.
RAID Level:
Select the desred RAID level:
RAID 0 (Performance) :
A volume optmzed for performance wll allow you to access your data more quck-
ly.
RAID 1 (Redundancy) :
A volume optmzed for data redundancy wll provde you wth a realtme duplcate
copy of your data. Note: Only half of the avalable volume space wll be avalable for
data storage.
RAID 5 (Useful) :
RAID 5 can be used on three or more dsks, wth zero or more spare-dsks. The
resultng RAID-5 devce sze wll be (N-1)*S, where N s the how many drve, S s the
sze of the smallest drve n the array. If one of the dsks fal, all data are stll ntact.
It can rebuld the dsk from the party nformaton. If spare dsks are avalable, recon-
structon wll begn mmedately after the devce falure. If two dsks fal smultane-
ously, all data are lost. RAID-5 can survve one dsk falure, but not two or more. Both
read and wrte performance usually ncrease, but can be hard to predct how much.
Reads are smlar to RAID-0 reads, wrtes can be ether rather expensve (requrng
read-n pror to wrte, n order to be able to calculate the correct party nformaton),
or smlar to RAID-1 wrtes. The wrte efcency depends heavly on the amount of
memory n the machne, and the usage pattern of the array. Heavly scattered wrtes
C-20
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
(3) Select Member Hard Drve(s)
Then select the member dsk (the target dsk) that you wsh to use and then clck -->
to move t to the Selected feld. Then clck Next to contnue.
Please note that the exstng data on the selected hard drve(s) wll be deleted perma-
nently. Do not forget to back up all the mportant data before contnung.
Intel SATA RAID MS-7583
C-21
Intel SATA RAID MS-7583
(4) Specfy Volume Sze
Specfy the amount of avalable array space to be used by the new RAID volume. You
may enter the amount n the space or use the slder to specfy. It s recommended you
use 100% of the avalable space for the optmzed usage. For RAID 0 volume, f you do
not specfy 100% of the hard drve space, the rest hard drve space wll be worked as
RAID 1 volume, whch s the new technology called Intel Matrx RAID. Then clck Next
to contnue.
(5) Start Creatng RAID Volume from Exstng Hard Drve Wzard
Before you contnue the procedure of RAID volume creaton from exstng hard drve,
read the dalogue box below carefully. Please note that once you clck Fnsh, the
exstng data on the selected hard drve(s) wll be deleted permanently and ths opera-
ton cannot be undone. It s crtcal that you backup all mportant data before selectng
Fnsh to start the mgraton process.
C-22
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
(6) Start Mgraton
The mgraton process may take up to two hours to complete dependng on the sze of
the dsks beng used and the strp sze selected. A dalogue wndow wll appear stat-
ng that the mgraton process may take consderable tme to complete, meanwhle a
popup dalogue at the taskbar wll also show the mgraton status. Whle you can stll
contnue usng your computer durng the mgraton process, once the mgraton process
starts, t cannot be stopped. If the mgraton process gets nterrupted and your system
s rebooted for any reason, t wll pck up the mgraton process where t left of. You wll
be provded wth an estmated completon tme (the remanng tme wll depend on your
system) once the mgraton process starts.
The followng screen appears f the mgraton process s completed successfully. Then
you have to reboot your system to use the full capacty of the new volume.
Intel SATA RAID MS-7583
C-23
Intel SATA RAID MS-7583
RECOVERY VOLUME CREATlON
A recovery volume can be created usng Advanced mode n the Intel Matrx Storage
Console.
Important
Creatng a recovery volume wll permanently delete any exstng data on the drve se-
lected as the recovery drve. Back up all mportant data before begnnng these steps.
Recovery Volume n Advanced Mode Creaton
To create a recovery volume n Advanced mode, use the followng steps:
Open the Intel Matrx Storage Console. (Start --> All Programs --> Intel Matrx Stor-
age Manager --> Intel Matrx Storage Console)
Select Advanced Mode n the Vew menu.
Select Create Recovery Volume n the Actons menu.
1.
2.
3.
Select Next to contnue. 4.
C-24
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
Select a hard drve to be used as the recovery hard drve for the recovery volume. 7.
Modfy the recovery volume name f you wsh.
Select a hard drve to be used as the master hard drve for the recovery volume.
5.
6.
Intel SATA RAID MS-7583
C-25
Intel SATA RAID MS-7583
Select an update polcy. 8.
Select Fnsh to begn recovery volume creaton. 9.
C-26
Intel SATA RAID MS-7583 Intel SATA RAID MS-7583
DEGRADED RAlD ARRAY
A RAID 1, RAID 5 or RAID 10 volume s reported as degraded when one of ts hard drve
members fals or s temporarly dsconnected, and data mrrorng s lost. As a result, the
system can only utlze the remanng functonal hard drve member. To re-establsh
data mrrorng and restore data redundancy, refer to the procedure below that corre-
sponds to the current stuaton.
Mssng Hard Drve Member
Make sure the system s powered of.
Reconnect the hard drve.
Reboot the system to Wndows; the rebuld wll occur automatcally.
Faled Hard Drve Member
Make sure the system s powered of.
Replace the faled hard drve wth a new one that s of equal or greater capacty.
Reboot the system to Intel RAID Opton ROM by press <Ctrl> and <I> keys smul-
taneously durng the Power-On Self Test (POST).
1.
2.
3.
1.
2.
3.
Select the port of the destnaton dsk for rebuldng, and then press ENTER. 4.
Intel SATA RAID MS-7583
C-27
Intel SATA RAID MS-7583
Ext Intel RAID Opton ROM, and then reboot to Wndows system.
When prompted to rebuld the RAID volume, clck Yes.
The Intel(R) Storage Utlty wll be launched. Rght-clck the new hard drve and
select Rebuld to ths Dsk. The Rebuld Wzard wll be launched whch wll gude
you through the process of rebuldng to the new hard drve.
5.
6.
7.
B-D-1
Ths appendx wll assst users n confgurng and en-
ablng RAID functonalty on platforms
The JMcron RAID soluton supports RAID level 0 (strp-
ng), RAID level 1 (mrrorng), RAID level 10 (strpng and
mrrorng) and JBOD (Concatenate).
Appendx D
JMcron RAID
Introducton
D-2
JMcron RAID Introducton MS-7583 JMcron RAID Introducton MS-7583
lNTRODUCTlON
JMcron JMB363 ofers RAID level 0 (Strpng), RAID level 1 (Mrrorng and Duplexng),
RAID level 10 (A Strpe of Mrrors) and JBOD (Concatenate).
RAID 0 breaks the data nto blocks whch are wrtten to separate hard drves. Spread-
ng the hard drve I/O load across ndependent channels greatly mproves I/O perfor-
mance. RAID 1 provdes data redundancy by mrrorng data between the hard drves
and provdes enhanced read performance. RAID 10 Not one of the orgnal RAID levels,
multple RAID 1 mrrors are created, and a RAID 0 strpe s created over these. JBOD
provdes a method for combnng drves of dferent szes nto one large dsk.
Important
Ths manboard supports RAID 0/ RAID 1 or JBOD mode only.
The least number of hard drves for RAID 0, RAID 1 or JBOD mode s 2.
All the nformaton/ volumes/ pctures lsted n your system mght dfer from the llus-
tratons n ths appendx. RAID Confguraton
1.
2.
3.
Important
Please follow the nstructon below to make an JMcron RAID Drver for yourself.
Insert the MSI DVD nto the DVD-ROM drve.
Clck the Browse DVD on the Setup screen.
Copy all the contents n the \\RAID\JMcron\NoIDE\Floppy32 (for 32-bt OS) or Flop-
py64 (for 64-bt OS) to a formatted foppy drve.
The drver dskette for JMcron RAID Controller s done.
When prompted, nsert the foppy dsk you created n step 3 and press Enter.
You should be shown a lst of avalable SCSI Adapters.
Select the approprate JMcron RAID controller and press ENTER.
The next screen should confrm that you have selected the JMcron RAID controller.
Press ENTER agan to contnue.
You have successfully nstalled the JMcron RAID drver, and Wndows setup
should contnue.
Leave the dsk n the foppy drve untl the system reboots tself. Wndows setup wll
need to copy the fles from the foppy agan after the RAID volume s formatted, and
Wndows setup starts copyng fles.
For Wndows Vsta:
After selectng the locaton to nstall Wndows Vsta, please clck on the Load Drver
button to nstall the RAID drver. Please refer the Important notce above to make a
RAID Drver medum. And then, follow the nstructons to complete the RAID drve n-
stallaton and the Wndows Vsta nstallaton.
4.
5.
6.
7.
8.
9.
Note: For Wndows XP, you can use the USB foppy drve only. For Wndows Vsta you
can use CD/ DVD/ USB drve.
D-12
JMcron RAID Introducton MS-7583 JMcron RAID Introducton MS-7583
Exstng Wndows Vsta/XP Drver Installaton
Insert the MSI DVD nto the DVD-ROM drve.
The DVD wll auto-run and the setup screen wll appear.
Under the Drver tab, clck on JMcron JMB362 Drvers.
The drvers wll be automatcally nstalled.
Confrmng Wndows Vsta/XP Drver Installaton
From Wndows Vsta/XP, open the Control Panel from My Computer followed by
the System con.
Choose the Hardware tab, then clck the Devce Manager tab.
Clck the + n front of the SCSI and RAID Controllers hardware type. The drver
JMcron JMB36X Controller should appear.
1.
2.
3.
4.
1.
2.
3.
JMcron RAID Introducton MS-7583
D-13
JMcron RAID Introducton MS-7583
JMlCRON RAlD CONFlGURER
There s an applcaton called JMRadTool whch helps you perform the followng tasks
of JMcron RAID.
Vewng RAID Array Confguratons: Vew an array confguraton (mrrored, strped)
Creatng RAID Arrays
Deletng a RAID Array
Rebuldng RAID Arrays
Solvng Mrror Confct
Vew RAID Array Confguratons
Left-clck the Show Dsks button and the nformaton of all hard dsks wll dsplay on
the rght sde of the wndow.
Left-clck the name of the dsk array and the nformaton of all hard dsks of the selected
dsk array wll dsplay on the rght sde of the wndow. The nformaton of the dsk array
wll also dsplay on the lower-left part of the wndow.
D-14
JMcron RAID Introducton MS-7583 JMcron RAID Introducton MS-7583
Create RAID
JMRadTool supports the creaton of RAID 0, 1 and JBOD.
Left-clck the Create Rad button.
A CREATE RAID WIZARD dalogue wll dsplay on the screen, followng the de-
scrpton of every step to complete the creaton.
Create RAID from Exstng Dsk
You can combne the Exstng Dsk (Source dsk may content OS and Data) wth other
HD (must be larger than source Dsk) to be RAID. The data on Source Dsk wll be re-
served. After RAID s bult, system wll need to reboot.
Left-Clck the Create RAID from Exstng Dsk con on the toolbar.
A CREATING RAID FROM EXISTING DISK wzard dalogue wll dsplay on the
screen, followng the descrpton of every step to complete the creaton.
1.
2.
1.
2.
JMcron RAID Introducton MS-7583
D-15
JMcron RAID Introducton MS-7583
Remove RAID
There are two ways you can choose to remove RAID.
Way 1
Rght-clck the name of the dsk array you want to delete and the Remove
menu wll appear. Select the Remove Rad of the pop-up menu.
1.
A warnng message appears to remnd you that the data wll be lost. Press the Yes
button f you really want to delete the dsk array.
2.
D-16
JMcron RAID Introducton MS-7583 JMcron RAID Introducton MS-7583
Way 2
Left-Clck the Remove Rad con on the toolbar.
A REMOVE RAID wzard dalogue wll dsplay on the screen, followng the de-
scrpton of every step to complete the deleton.
1.
2.
Rebuld RAID
RAID 1 can be rebuld whle RAID 0, JBOD cannot be rebuld. There are two ways you
can choose to rebuld RAID.
Way 1
Rght-clck the name of the dsk array you want to rebuld and the Rebuld menu
wll appear.
1.
JMcron RAID Introducton MS-7583
D-17
JMcron RAID Introducton MS-7583
Select Rebuld Rad.
A REBUILD RAID WIZARD dalogue wll dsplay on the screen, followng the de-
scrpton of every step to complete the rebuldng.
2.
3.
Way 2
If the dsk array needs to rebuld then the rebuld button wll be enablng on the
toolbar.
1.
D-18
JMcron RAID Introducton MS-7583
Left-Clck the Rebuld Rad button on the toolbar.
A REBUILD RAID WIZARD dalogue wll dsplay on the screen, followng the de-
scrpton of every step to complete the rebuldng.
2.
3.
Solve Mrror Confct
If the confct occurs, t wll show the REBUILDING RAID WIZARD dalogue to ask you
f you want to rebuld RAID, followng the descrpton of every step to rebuld the RAID.