Vous êtes sur la page 1sur 21

Assessment System Skip to Time Left | Skip to Navigation | Skip to Assessment Items

Take Assessment - DsmbISP Final Exam - CCNA Discovery: Working at a Small-toMedium Business or ISP (Version 4.1) Time Remaining:

<Prev Page: GO A tracert command is run on a host to determine if another host can be reached across a network. Whic events will occur if connectivity with the other host is unsuccessful? (Choose two.) The command will display all the successful hops a packet makes before it is lost. The command will calculate the time between successful and unsuccessful packets. The host on which the command is run will send a UDP request message to the other host. The command helps to determine where a packet was lost on the path from the source to the destina All hops between the two hosts display !!!!! to signify success.

Showing 1 of 6

Next>

Refer to the exhibit. There is no dynamic routing protocol that is running on this network. The network administrator adds a static route via the use of the ip route 192.168.4.0 255.255.255.0 10.1.1.6 which router should the network administrator issue this command? R1 R2 R3 R4 3 Which statement correctly describes MIB? It is software that is installed on a device which in turn is managed by SNMP. It is installed on a system that is used to monitor networking devices.

It is a database that a device keeps about itself concerning network performance parameters. It is a communication protocol that is used between the management station and the management ag 4

Refer to the exhibit. The network administrator has added a route by using the ip route 10.13.13.0 255.255.255.0 192.168.1.1 command on R1. Hosts on the 10.12.12.0 network cannot communicate with on the 10.13.13.0 network. What is the reason for this? The gateway of last resort is not set. The destination prefix mask is incorrectly configured. The routing protocol has not been configured on R1. The static route has not been configured correctly. 5 What is a feature of PAT? It maps IP addresses to URLs. It displays private IP addresses to public networks. It sends acknowledgments of received packets. It allows multiple hosts on a single LAN to share globally unique IP addresses.

Refer to the exhibit. Devices need to connect to the file server from remote networks. What method sho used to provide the file server with an IP address to allow these connections? static NAT static PAT dynamic NAT dynamic PAT 7

What are three features of the TCP protocol? (Choose three.) It provides retransmission of data packets if they are lost during transmission. It is a connectionless protocol. It uses a three-way handshake between the sending and receiving systems to establish each conversa It specifies how messages are reassembled at the destination host. It requires only 8 bytes of overhead. It breaks the data packet into datagrams.

Refer to the exhibit. Which subnet mask would accommodate the number of hosts indicated for all subn major network address was 192.168.25.0/24? 255.255.0.0 255.255.224.0 255.255.255.0 255.255.255.224 255.255.255.240 255.255.255.248 9

Refer to the exhibit. A new router has been configured for the first time with the commands that are di Which two facts can be determined about the interface of this router? (Choose two.) It will act as a DCE device. It is administratively down. It will operate at a speed of 6.4 Mb/s. It is the first interface on slot 0 of controller 1. Because MOTD is not configured, the interface will not work. 1 0

The show ip route command was executed on one of the routers shown in the graphic and the followin output was displayed: C 192.168.4.0/24 is directly connected, Serial0/0 R 192.168.5.0/24 [120/1] via 192.168.4.2, 00:00:19, Serial0/0 R 192.168.1.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1 R 192.168.2.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1 C 192.168.3.0/24 is directly connected, Serial0/1 From which router was this command executed? A B C D

Showing 1 of 6

Next>

Page:

GO

<Prev

All content copyright 1992-2008 Cisco Systems, Inc. Privacy Statement and Trademarks

Assessment System Skip to Time Left | Skip to Navigation | Skip to Assessment Items

Take Assessment - DsmbISP Final Exam - CCNA Discovery: Working at a Small-to-

Medium Business or ISP (Version 4.1) Time Remaining:

<Prev Page: GO 11 Which statement correctly describes an SLA? It lists the terms of the agreement between the user and the manufacturer of the system. It outlines the management, monitoring, and maintenance of a network. It specifies the software and hardware configurations of a system. It describes the operation of a system. 12

Showing 2 of 6

Next>

Refer to the exhibit. R1 and R2 are configured with the commands that are displayed. All interfaces are p configured, but neither router is receiving routing updates. What two things can be done to solve the pro (Choose two.) Configure the routing protocol on R1 for network 10.0.0.0. Configure the routing protocol on R2 for network 10.0.0.0. Configure the routing protocol on R1 for network 192.168.4.0. Configure the routing protocol on R1 for network 192.168.2.0. Configure the routing protocol on R2 for network 192.168.1.0. Configure the routing protocol on R2 for network 192.168.3.0.

13 Which statement correctly describes the difference between HTTP and HTTPS? The maximum number of simultaneous connections that a server can support for HTTPS is more tha HTTP. HTTPS and HTTP use different client request-server response processes. HTTPS authenticates and encrypts the data being transferred between the client and the web server.

HTTPS specifies the rules for passing data between the physical layer and the data link layer. 14 Which WAN connection provides a dedicated circuit with fixed bandwidth available at all times? point-to-point circuit-switched packet-switched cable

15 Which statement describes a feature of TCP? It provides low overhead data delivery. It acknowledges the receipt of packets. It does not provide error checking. It is a connectionless protocol.

Which type of cable may be used for backbone cabling between data centers that are located on differen 16 and that are separated by a distance of 1640 feet (500 meters)? STP UTP coaxial fiber-optic

17 Which two services are required to enable a computer to receive dynamic IP addresses and access the In using domain names? (Choose two.) DNS WINS HTTP DHCP SMTP 18 What is the function of the forward lookup DNS zone in the DNS name resolution process? It resolves fully qualified domain names into IP addresses. It stores the information about the domain namespace structure. It forwards zone information updates to the secondary server. It maintains a database of ARP entries for all servers.

19 A building has experienced a power outage. When the power returns, none of the devices on one floor ca the Internet. The network administrator checks the switch in the IDF that these devices are connected to notes that the SYST LED on the front of the switch is amber.

What is a possible cause of this problem? The switch is functioning properly. The switch has failed POST. The switch configuration file was not saved to NVRAM. The connection between the switch and the server did not autonegotiate speed and duplex properly. 20

Refer to the exhibit. The network administrator has added networks A and B to router R1. Which two subnetwork numbers should be used to address networks A and B so that these networks use the same su mask as networks C and D? (Choose two.) 192.168.1.32/26 192.168.1.64/26 192.168.1.96/26 192.168.1.160/26 192.168.1.192/26

Showing 2 of 6

Next>

Page:

GO

<Prev

All content copyright 1992-2008 Cisco Systems, Inc. Privacy Statement and Trademarks Assessment System Skip to Time Left | Skip to Navigation | Skip to Assessment Items

Take Assessment - DsmbISP Final Exam - CCNA Discovery: Working at a Small-toMedium Business or ISP (Version 4.1) Time Remaining:

Showing 3 of 6 21

Next>

Page:

GO

<Prev

Refer to the exhibit. What method is most commonly employed by large ISPs, such as ISP1, ISP2, and IS exchange and maintain routing information? static routes IGP protocols EGP protocols directly connected routes 22

Refer to the exhibit. Which combination of cable types should be used to complete the connection? Cable A - straight-through; Cable B - straight-through; Cable C - serial Cable A - straight-through; Cable B - straight-through; Cable C - rollover Cable A - rollover; Cable B - straight-through; Cable C - crossover Cable A - straight-through; Cable B - crossover; Cable C - serial

23 A user is able to ping an FTP server across a WAN but is unable to download files from the server. Wha be checked to resolve this problem? the NIC drivers the IP configuration the LED status of the NIC firewall settings 24

Refer to the exhibit. A computer with the displayed IP settings is unable to access a server on the 192.16 network using the server IP address but can access hosts on the 192.168.1.0 network. What should the ne administrator do to troubleshoot this problem? Issue the ping 192.168.1.1 command on the host to determine if the host can communicate with the gateway. Issue the ipconfig /all command to determine if a DNS server IP address was configured. Verify that the host has a link light. Check the cabling of the host. 25 What is a characteristic of Syslog?

It requires users to prove their identity with the use of a username and password before users can acc network resources. It listens to network traffic and sends an alert to a management station to track which applications ar and the length of time for which they are used. It enables devices to send information to a daemon that runs on a management station. It provides users the rights to access specific resources and perform specific tasks. 26 Which type of address is 192.168.17.111/28? host address network address broadcast address multicast address

27 What is the basis for determining the vector component of a route in the distance vector routing algorithm the bandwidth of the route the reliability of the route the IP address of the next hop the number of hops 28

Refer to the exhibit. What does the highlighted value 120 represent? the number of hops between the router and network 10.0.5.0 the administrative distance of the routing protocol the UDP port number that is used for forwarding traffic the bandwidth that is allocated to the serial interface

29 What will a router do with a packet that is destined for a host with the IP address 192.168.1.5/24 if no en the 192.168.24.0/24 network exists in the routing table? It will broadcast the packet out of all of its active interfaces except the interface that received the pac

It will send the packet back to the source address. It will drop the packet. It will broadcast the packet out of all of its active interfaces.

How many host addresses can be assigned in each subnetwork when using network address 172.16.0.0 w 30 subnet mask 255.255.252.0? 256 510 512 1022 024

Showing 3 of 6

Next>

Page:

GO

<Prev

All content copyright 1992-2008 Cisco Systems, Inc. Privacy Statement and Trademarks Assessment System Skip to Time Left | Skip to Navigation | Skip to Assessment Items

Take Assessment - DsmbISP Final Exam - CCNA Discovery: Working at a Small-toMedium Business or ISP (Version 4.1) Time Remaining:

<Prev Page: GO 31 Which routing protocol depends on the DUAL algorithm to calculate the shortest path to a destination? OSPF EIGRP RIP BGP 32

Showing 4 of 6

Next>

Refer to the exhibit. Router R1 has been configured with the commands that are displayed. Which fact c determined from the configuration? All passwords are encrypted. The privileged EXEC mode password is password1. The router can support four Telnet sessions simultaneously. The router can be accessed from the console without using any password.

33 Which two statements are true about resolvers in the DNS hierarchy? (Choose two.) The resolvers attempt to resolve client queries by using the records that the resolvers maintain in the database files. The DNS server queries the resolvers to translate the domain name to an IP address. There can be only one resolver in a DNS zone. Resolvers may be configured on DNS clients. The DNS server uses the resolver to forward the name resolution request to another DNS server. 34

Refer to the exhibit. The network administrator uses the command below to configure a default route on RTB(config)# ip route 0.0.0.0 0.0.0.0 fa0/0

A ping issued from PC3 is successful to RTB. However, echo request packets arrive at PC1 but the echo do not make it back to PC3. What will fix this problem? RTA must be configured to forward packets to the 192.168.2.0 network. The ip route command needs to be edited so that the next hop address is 10.1.1.5. The ip route command needs to be edited so that the 192.168.2.1 address is the next hop address. The ip route command should be removed from the RTB router configuration. Another default route should be configured on RTA with a next hop address of 10.1.1.6. 35 When does a router enter the setup mode? when the Cisco IOS is missing in flash when the configuration is missing in NVRAM when the setup command is run from the user mode when the boot system command is missing in the configuration 36

Refer to the exhibit. The S0/0/0 interface of R2 is configured correctly with the default encapsulation. W configuration should be implemented at the S0/0/0 interface of R1 to complete the connection between t routers? R1(config-if)# ip address 192.168.1.31 255.255.255.252 R1(config-if)# no shutdown R1(config-if)# ip address 192.168.1.33 255.255.255.252 R1(config-if)# encapsulation PPP R1(config-if)# no shutdown R1(config-if)# ip address 192.168.1.28 255.255.255.252 R1(config-if)# encapsulation PPP R1(config-if)# no shutdown R1(config-if)# ip address 192.168.1.29 255.255.255.252

R1(config-if)# no shutdown 37 If the start-up configuration is not found in NVRAM, where will the router look for it next by default? flash ROM RAM TFTP server 38 Which routing protocol excludes the subnet information from routing updates? EIGRP OSPF RIPv1 BGP

39 Which two statements are true about the c:\> ping command? (Choose two.) It tests the accessibility of an IP address. It sends a TCP packet to the destination IP address. It sends an ICMP echo request packet to the destination address. It traces the route of a data packet from the source to the destination. It determines where a packet was lost or delayed during transmission. 40

Refer to the exhibit. A network administrator is troubleshooting the serial connection between R1 and R2 is no communication between R1 and R2. Based on the output of the show ip interface brief the cause of the problem? There is a misconfiguration of IP addresses. There is a mismatch of encapsulation methods. The no shutdown command has not been issued on R2. The routing protocols are not compatible.

Showing 4 of 6

Next>

Page:

GO

<Prev

All content copyright 1992-2008 Cisco Systems, Inc. Privacy Statement and Trademarks Assessment System Skip to Time Left | Skip to Navigation | Skip to Assessment Items

Take Assessment - DsmbISP Final Exam - CCNA Discovery: Working at a Small-toMedium Business or ISP (Version 4.1)

Time Remaining:

<Prev Page: GO 41 A customer reports connectivity problems to an ISP technician. Upon questioning the customer, the tech discovers that all network applications are functioning except for FTP. What should the technician suspe problem? misconfigured firewall bad port on switch or hub misconfigured IP addressing on the customer's workstation wrong DNS server configured on the customer's workstation wrong default gateway configured on the customer's workstation 42

Showing 5 of 6

Next>

Which statement is true about FTP implementations? The protocol interpreter (PI) function engages once the data transfer process (DTP) function is comp The DTP function is responsible for the login sequence. FTP requires two connections, one for control and one for data. Both the PI and the DTP close automatically when the transfer is complete.

43 Which two subnet masks can be used when subnetting a Class A IP address? (Choose two.) 255.0.0.0 240.0.0.0 224.0.0.0 255.255.0.0 255.255.255.0 44

Refer to the exhibit. Which two statements describe the data conversation shown? (Choose two.) The data conversation was started by the HTTP application process running on the client.

The data conversation is identified by TCP port 80 on the client. The user started the data conversation by sending an e-mail. The IP address of the Internet server is 192.168.17.43. The Internet server will send data to port 8547 on the client. 45 How do port filtering and access lists help provide network security? They prevent specified types of traffic from reaching specified network destinations. They alert network administrators to various type of denial of service attacks as they occur. They prevent viruses, worms, and Trojans from infecting host computers and servers. They enable encryption and authentication of confidential data communications.

A hacker attempts to reach confidential information that is stored on a server inside the corporate networ 46 network security solution inspects the entire packet, determines that it is a threat, and blocks the packet f entering the inside network. Which security measure protected the network? an IDS an IPS a host-based firewall Anti-X software

47 While troubleshooting a connectivity issue between two directly connected routers, the network adminis checks the encapsulation settings on the serial interfaces of both routers. Which layer of the OSI model i administrator troubleshooting? application layer network layer data link layer physical layer 48 What is the effect of issuing the hostname RouterA command on a router? A description will be configured on the router interfaces identifying them as belonging to RouterA. The router will attempt to establish a connection to the host with the name RouterA. The router will map an IP address to the domain name RouterA. The router prompt will change from Router(config)# to RouterA(config)#

49 Which cable should be used to connect a PC to the console port of a Cisco router? serial crossover rollover straight-through

The network administrator can ping a remote router but is unable to telnet to it. At what layer of the OSI 50 does this error occur? physical network data link application

Showing 5 of 6

Next>

Page:

GO

<Prev

All content copyright 1992-2008 Cisco Systems, Inc. Privacy Statement and Trademarks Assessment System Skip to Time Left | Skip to Navigation | Skip to Assessment Items

Take Assessment - DsmbISP Final Exam - CCNA Discovery: Working at a Small-toMedium Business or ISP (Version 4.1) Time Remaining:

<Prev Page: GO 51 What are two reasons for issuing the show ip protocols command on a router? (Choose two.) It displays the routing protocol in use. It displays the routed protocol in use. It displays the routing activity in real time. It displays the static routes that are contained in the routing table. It displays the networks that are being advertised by the router. 52 What is an example of a dedicated point-to-point WAN link? ISDN Frame Relay dialup T1/E1

Showing 6 of 6

Next>

53

Refer to the exhibit. What two conclusions can be drawn about the exhibited command output? (Choose Router RTB is directly connected to a router and a switch. Router RTB is able to ping its directly connected neighbors. The network administrator needs to log in to the neighboring devices to gather this information. Router RTB has Layer 2 connectivity with two neighboring devices. Router RTB is connected to two Cisco devices by FastEthernet links. 54 Which address does a switch use for implementing port security? the source IP address the source MAC address the destination IP address the destination MAC address

55

Refer to the exhibit. The interfaces on R1 and R2 have been properly configured with the IP addresses a No dynamic routing protocols have been configured. The network administrator has entered the comman are shown in the exhibit.

Which two additional commands need to be entered on the routers to enable host A to access the Interne (Choose two.) R2(config)# ip route 0.0.0.0 0.0.0.0 S0/0/0 R1(config)# ip route 0.0.0.0 0.0.0.0 S0/0/0 R1(config)# ip route 0.0.0.0 0.0.0.0 198.213.219.1 R2(config)# ip route 192.168.1.0 255.255.255.0 10.1.1.1 R1(config)# ip route 198.133.219.1 255.255.255.0 10.1.1.2 56 Which two parameters are stored in the routing table? (Choose two.) the best route to reach remote networks the interfaces used to forward packets the ARP requests from connected routers the number of times a route has been used by the router the packets that are placed in the buffer before being forwarded

Showing 6 of 6

Next>

Page:

GO

<Prev

All content copyright 1992-2008 Cisco Systems, Inc. Privacy Statement and Trademarks

Vous aimerez peut-être aussi