Académique Documents
Professionnel Documents
Culture Documents
TL074C,AC
Low Input Noise Voltage: 18 nV/ Hz Typ Low Harmonic Distortion: 0.01% Typ Low Input Bias and Offset Currents High Input Impedance: 1012 Typ High Slew Rate: 13 V/s Typ Wide Gain Bandwidth: 4.0 MHz Typ Low Supply Current: 1.4 mA per Amp
8 8 1 1
PIN CONNECTIONS
Offset Null 1 Inv + Input 2 Noninvt Input 3 VEE 4 + 8 NC 7 VCC 6 Output 5 Offset Null
VCC
VEE 4
7 Output B 6 Inputs B 5
14 1
PIN CONNECTIONS
Output 1 1 14 Output 4
+
ORDERING INFORMATION
Op Amp Function Single TL071ACP TL072CD Dual TL072ACP Quad TL074CN, ACN TA = 0 to +70C TA = 0 to +70C Device TL071CD TA = 0 to +70C Operating Temperature Range Package SO8 Plastic DIP SO8 Plastic DIP Plastic DIP
Inputs 1
2 3
13 12
Inputs 4
11 VEE 2 3
+
10 9
Inputs 3
8 Output 3
Rev 1
NOTES: 1. The magnitude of the input voltage must not exceed the magnitude of the supply voltage or 15 V, whichever is less. 2. The output may be shorted to ground or either supply. Temperature and/or supply voltages must be limited to ensure that power dissipation ratings are not exceeded. 3. ESD data available upon request.
NOTES: 1. Tlow = 0C for TL071C,AC Thigh = 70C for TL071C,AC 0C for TL072C,AC Thigh = 70C for TL072C,AC 0C for TL074C,AC Thigh = 70C for TL074C,AC 2. Input Bias currents of JFET input op amps approximately double for every 10C rise in junction temperature as shown in Figure 3. To maintain junction temperature as close to ambient temperature as possible, pulse techniques must be used during testing.
1.0 k
+ VO
RL
CL = 100 pF
AVOL
NOTES: 1. Tlow = 0C for TL071C,AC Thigh = 70C for TL071C,AC 0C for TL072C,AC Thigh = 70C for TL072C,AC 0C for TL074C,AC Thigh = 70C for TL074C,AC 2. Input Bias currents of JFET input op amps approximately double for every 10C rise in junction temperature as shown in Figure 3. To maintain junction temperature as close to ambient temperature as possible, pulse techniques must be used during testing.
10
1.0
0.1
0.01 100 75
50
25
25
50
75
100
125
150
f, FREQUENCY (Hz)
20
10
5.0 0 0.1
0.2
0.4
0.7 1.0
2.0
4.0
7.0
10
5.0
10
15
20
50
25
25
50
75
100
125
100
10
1.0 k
10 k
f, FREQUENCY (Hz)
1.20 1.15 NORMALIZED SLEW RATE 1.10 1.05 1.0 0.95 0.90 0.85 0.80 75 50 25 0 25 50 75 100 125
0.5
1.0
5.0
10
50
100
f, FREQUENCY (Hz)
Q6 Inputs + J1 J2 2.0 k Q17 Q20 Q15 10 pF Q14 Q21 Q12 Q10 Q13 Q11 Q16 Q9 Q8 Q7 Q18 Offset Null (TL071 only) 1.5 k 1.5 k VEE Q25 Q22 Q24 Q19 Q23 24 J3
0.033 F
0.033 F 10 k
VCC TL071 + 68 k
Output
VEE TurnOver Frequency = 1.0 kHz Bass Boost/Cut 20 dB at 20 Hz Treble Boost/Cut 19 dB at 20 kHz
R Input
R C1
TL071 +
R1
B
1 4
NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC 10_ 0.030 0.040
F
NOTE 2
A L
C T
SEATING PLANE
J N D K
M
G 0.13 (0.005) T A
M
D
5
E
1 4
0.25
h B C e A
SEATING PLANE
X 45 _
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETERS. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.18 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_
L 0.10 A1 0.25 B
M
C B
B
1 7
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 10_ 0.38 1.01
A F N T
SEATING PLANE
L C
K H G D 14 PL 0.13 (0.005)
M
J M
DIM A B C D F G H J K L M N
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 13036752140 or 18004412447 Customer Focus Center: 18005216274 Mfax: RMFAX0@email.sps.mot.com TOUCHTONE 16022446609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System US & Canada ONLY 18007741848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 85226629298 http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4321, NishiGotanda, Shinagawaku, Tokyo 141, Japan. 81354878488
TL071C/D
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.