Académique Documents
Professionnel Documents
Culture Documents
DESCRIPTION
The OKI MSM534002E is a high-speed CMOS Mask ROM that can electrically switch between 262,144-word x 16-bit and 524,288-word x 8-bit configurations. The MSM534002E operates on a single 5.0V power supply and is TTL compatible. The chip's asynchronous I/O requires no external clock assuring easy operation. A power-down mode provides low power dissipation when the chip is not selected. The CE and OE pins are provided as control signals www.DataSheet4U.com that permit three-stated output allowing easy memory expansion on a system bus. The MSM534002E is suited for use as large capacity fixed memory for microcomputers and data terminals.
FEATURES
Single 5.0V power supply 262,144-words x 16-bit/524,288-words x 8-bit Access time 100ns MAX Input/Output TTL compatible Tri-State output configurations Internal powerdown function Packages 40-PIN PLASTIC DIP (DIP40-P-600-2.54) 40-PIN PLASTIC SOP (SOP40-P-525-1.27-K) 44-PIN PLASTIC TSOP (TSOPII44-P-400-0.80-K) 4MEPROM (40-PIN) pin compatible
MSM534002E
PIN CONFIGURATION
A17 A7 A6 A5
www.DataSheet4U.com
1 2 3 4 5 6 7 8 9
40 A8 39 A9 38 A10 37 A11 36 A12 35 A13 34 A14 33 A15 32 A16 31 BYTE 30 VSS 29 D15/A-1 28 D7 27 D14 26 D6 25 D13 24 D5 23 D12 22 D4 21 VCC 40PINDIP/SOP
44 NC 43 NC 42 A8 41 A9 40 A10 39 A11 38 A12 37 A13 36 A14 35 A15 34 A16 33 BYTE 32 VSS 31 D15/A-1 30 D7 29 D14 28 D6 27 D13 26 D5 25 D12 24 D4 23 VCC
A4 A3 A2 A1 A0
Function Data output / address input Address input Data output Chip enable Output enable Mode switch Power supply
MSM534002E
BLOCK DIAGRAM
VCC VSS A-1 BYTE
CE
www.DataSheet4U.com
OE
CE
OE
Control
D0 D1
D2 D3
D4 D5
D6 D7
D8
FUNCTION TABLE
CE H L L L L OE X H L L L BYTE X X H L L A-1/D15 X X
Input Inhibited (D15)
LSB A0 A-1
L H
MSM534002E
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
Parameter Power Supply Voltage Input Voltage Output Voltage Power Dissipation Operating Temperature Storage Temperature
www.DataSheet4U.com
Rated Value 0.3 to 7 0.3 to VCC + 0.5 0.3 to VCC + 0.5 1.0 0 to 70 55 to 150
Unit V V V W C C
DC Characteristics
(VCC = 5V10%, Ta = 0 to 70C) Parameter "H" Output Voltage "L" Output Voltage Input Leakage Current Output Leakage Current Power Supply Current (Operating) Power Supply Current (Standby) Symbol VOH VOL ILI ILO ICC ICCS1 ICCS Conditions IOH = 400A IOH = 2.1mA VI = 0 to VCC VO = 0 to VCC CE = VIH MIN CE = VIL,OE = VIH,tC = 100ns CE = VCC0.2V CE = VIH MIN Min. 2.4 10 10 Rated Value Typ. Max. 0.4 10 10 45 50 500 Unit V V A A
mA A A
MSM534002E
AC CHARACTERISTICS
Timing conditions
Parameter Input Signal Level Transtion Time Timing Reference Level Load Condition
www.DataSheet4U.com
Read Cycle
(Ta = 0 to 70C) Parameter Cycle time Address Access time CE Access time OE Access time CE Output Disable time OE Output Disable time Output Hold time Symbol tC tACC tCE tOE tCHZ tOHZ tOH Conditions Rated Value Min. 100 0 0 0 Typ. Max. 100 100 50 40 30 Unit ns ns ns ns ns ns ns
MSM534002E
DOUT
tCHZ (Note 3)
Note)
1. CE is low level. 2. Address is fixed before or at the same time when CE level falls. 3. tCHZ & tOHZ indicate the time until floating. They are not determined by the output level.
I/O CAPACITANCE
Parameter Input Capacitance Output Capacitance Symbol CI CO Conditions VI=0V VO=0V Rated Value Min. Typ. Max. 8 10 Unit pF pF
Semiconductor
NOTICE
The information contained herein can change without notice owing to product and/or technical improvements. Before using the product, please make sure that the information being referred to is up-todate. The outline of action and examples for application circuits described herein have been chosen as an explanation for the standard action and performance of the product. When planning to use the product, www.DataSheet4U.com ensure that the external conditions are reflected in the actual circuit, assembly, and program please designs. When designing your product, please use our product below the specified maximum ratings and within the specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating temperature. Oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified operating range. Neither indemnity against nor license of a third partys industrial and intellectual property right, etc. is granted by us in connection with the use of the product and/or the information and drawings contained herein. No responsibility is assumed by us for any infringement of a third partys right which may result from the use thereof. The products listed in this document are intended for use in general electronics equipment for commercial applications (e.g., office automation, communication equipment, measurement equipment, consumer electronics, etc.). These products are not authorized for use in any system orapplication that requires special or enhanced quality and reliability characteristics nor in any system or application where the failure of such system or application may result in the loss or damage of property, or death or injury to humans. Such applications include, but are not limited to, traffic and automotive equipment, safety devices, aerospace equipment, nuclear power control, medical equipment, and life-support systems. Certain products in this document may need government approval before they can be exported to particular countries. The purchaser assumes the responsibility of determining the legality of export of these products and will take appropriate and necessary steps at their own expense for these. No part of the contents cotained herein may be reprinted or reproduced without our prior permission. All brand, company and product names are the trademarks or registered trademarks of their respective owners.
www.DataSheet4U.com