Académique Documents
Professionnel Documents
Culture Documents
Model EVMU / EVMUG / EVMUL Contents EBARA Stainless Steel Vertical Multistage
Item No.
Specifications
Selection Chart
Sectional View 824, 825 826, 827 830-832 833-835 840 842 824, 825 826, 827 830-832 833-835 840 842
EVMU3 EVMU5 EVMU10 EVMU18 EVMUG32 EVMUG45 EVMUG64 EVMUL3 EVMUL5 EVMUL10 EVMUL18 EVMUL32 EVMUL45 EVMUL64 804 803 804 805 803
808 809 810 811 812 806 807 808 809 810 811 812
800
rev. 03/07
EVMU
Model EVMU / EVMUG / EVMUL Features
Standard NEMA motors Integral thrust bearing on 5 HP and larger pumps to handle axial thrust loads Air vent in casing cover allows proper venting preventing air entrapment and dry run Liner ring is a self-aligning, floating design constructed to prevent swelling at high temperatures Tungsten carbide lower pump bearings and sleeves are standard construction for all services, providing maximum operating life Direct drive pump and motor shafts are keyed for positive, reliable power transmission with no adjustments necessary Flexible floating outer casing allows for thermal expansion in hot water applications, preventing deformation due to pressure fluctuations Anti-erosion measures a dish-shaped insert is fitted to the intermediate casing designed to promote smooth flow and prevent high velocity areas that accelerate erosion Square-edge six spline shaft (EVMU3-18) or twelve spline shaft (EVMU 32-64) provides positive location and drive of impellers eliminating wear Dimensions & flanges installation is to market accepted dimensions for easy upgrade of existing installations Mechanical seal Silicon/Carbon/Viton mechanical shaft seal Positive Sealing O-rings between intermediate casings provide positive sealing and increased efficiencies
Typical Applications
Water Supply Reverse Osmosis Water Boosting Washing Systems Fire Fighting Water Treatment Plants Boiler Feed Hot & Cold Water Circulation Irrigation Sprinkler Systems Filtration Heat Exchangers
801
rev. 03/07
EVMU
Model EVMU / EVMUG / EVMUL Model Designation Models EVMU 3, 5, 10, 18 EVMUL 3, 5, 10, 18 EBARA Stainless Steel Vertical Multistage
EVMU L 3- 2 F 0050 D 1 S
Model Type: EBARA Vertical Multistage (USA) (none) -304 SS Construction L - 316 SS Construction Nominal Size Total number of impellers Flanged Connections
Horsepower 0050=1/2 HP 0075=3/4 HP 0100=1.0 HP 0150=1.5 HP 0200=2.0 HP 0300=3.0 HP 0500=5.0 HP 0750=7.5 HP 1000=10 HP 1500=15 HP 2000=20 HP 2500=25 HP
EVMU G 32 3- 2 F 0750 T 3 S
EBARA Vertical Multistage (USA)
G - 304 SS with Cast iron bottom casing L - 316 SS Construction
Nominal size Total number of impellers Number of reduced diameter impellers Flanged Connections Horsepower 0500=5HP 0750=7.5HP 1000=10HP 1500=15HP 2000=20HP 2500=25HP 3000=30HP 4000=40HP 5000=50HP
802
rev. 03/07
EVMU
Model EVMU / EVMUL Specifications Models EVMU 3, 5, 10, 18 EVMUL 3, 5, 10, 18 EBARA Stainless Steel Vertical Multistage
EVMU
Size Suction ANSI raised face 11/4'' for EVMU 3 and 5 2'' for EVMU 10 and 18 ANSI raised face 11/4'' for EVMU 3 and 5 2'' for EVMU 10 and 18
EVMUL
Discharge
4'' for EVMUG64 Range of HP Range of Performance Capacity Head Liquid handled Type of liquid Temperature Working pressure Materials Impeller Intermediate casing Bottom casing Casing cover Outer casing Shaft Liner ring Motor bracket Base Pump Bearing Shaft Seal Mechanical seal EVMU AISI 304 AISI 304 AISI 304 AISI 304 AISI 304 AISI 316
1
/2 to
1/2 to 25HP at 3450 RPM 4 to 118 GPM 27 to 830 feet Clean water (for other clean liquids, consult factory) 5 to +248F (-15 to 120C) 370 PSI (25 Bar) max. (see page 813 for specifics) EVMUL EVMUG AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316
PTFE/AISI 316 Cast iron/304 Cast iron/304 Cast iron/316 Cast iron/316 Sealed ball bearing/tungsten carbide Silicon/Carbide/Carbon/FPM (see page 814 for construction details)
NEMA C/TC/TSC frame 60 Hz, 3450 RPM (2 poles) 208-230/460V Clockwise when viewed from motor end ISO 9906 annex A
803
rev. 01/08
EVMU
Model EVMUG / EVMUL Specifications Models EVMUG 32, 45, 64 EVMUL 32, 45, 64 EBARA Stainless Steel Vertical Multistage
EVMUG
Size Suction ANSI raised face 21/2'' for EVMUG32 3'' for EVMUG45 4'' for EVMUG64 ANSI raised face 21/2'' for EVMUG32 3'' for EVMUG45 4'' for EVMUG64 5 to 50HP at 3450 RPM 66 to 390 GPM 44 to 930 feet
EVMUL
Discharge
Range of HP Range of Performance Capacity Head Liquid handled Type of liquid Temperature Working pressure Materials Impeller Intermediate casing Bottom casing Casing cover Outer casing Shaft Liner ring Motor bracket Base Pump Bearing Shaft Seal Mechanical seal Motor Type Speed Three Phase Direction of Rotation Test standard
Clean water (for other clean liquids, consult factory) 5 to +248F (-15 to 120C) to 440 PSI (30 Bar) max. (see page 813 for specifics) AISI 304 AISI 304 Cast iron Cast iron AISI 304 AISI 316 PTFE/AISI 316 Cast iron Cast iron Cast iron/316 Cast iron/316 Sealed ball bearing/tungsten carbide Silicon/Carbide/Carbon/FPM (see page 815 for construction details) NEMA TC/TSC frame 60 Hz, 3450 RPM (2 poles) 208-230/460V Clockwise when viewed from motor end ISO 9906 annex A AISI 316 AISI 316 AISI 316 AISI 316 AISI 316 AISI 316
804
rev. 01/08
EVMU
Model EVMU / EVMUG / EVMUL Selection chart 60 Hz, Synchronous Speed 3450 RPM EBARA Stainless Steel Vertical Multistage
Q m3/h Q l/min 1000 900 700 H ft 500 400 300 200 150 100 75 50 40 30 20 12.5
1 25
2 40
3 72
10 140 250
20
30 500
40 700
50 1000
70
50 40 30 20
EVMU 18
15
5 10
5 US GPM lmp. GPM 5 5 10 10 20 20 30 30 50 50 100 150 200 300 400 500 100 150 200 300 400
805
rev. 03/07
EVMU
Model EVMU / EVMUL Performance Curves EVMU3 2 - EVMU3 18 EBARA Stainless Steel Vertical Multistage EVMU 3 Synchronous Speed: 3450 RPM
1
/2HP - 5HP
Min. Flow
806
rev. 03/07
EVMU
Model EVMU / EVMUL Performance Curves EVMU5 2 - EVMU5 16 EBARA Stainless Steel Vertical Multistage EVMU5 3/4 HP - 71/2 HP Synchronous Speed: 3450 RPM 250# ANSI 11/4'' 4-Bolt
Min. Flow
807
rev. 03/07
EVMU
Model EVMU / EVMUL Performance Curves EVMU10 2 - EVMU10 16 EBARA Stainless Steel Vertical Multistage EVMU10 11/2 HP -15 HP Synchronous Speed: 3450 RPM 250# ANSI 2'' 8-Bolt
Min. Flow
808
rev. 03/07
EVMU
Model EVMU / EVMUL Performance Curves EVMU18 2 - EVMU18 11 EBARA Stainless Steel Vertical Multistage EVMU18 5HP - 25HP Synchronous Speed: 3450 RPM 250# ANSI 2'' 8-Bolt
Min. Flow
6-11
809
rev. 03/07
EVMU
Model EVMUG / EVMUL Performance Curves EVMU32 1 EVMU32 4-3 EVMU32 5 EVMU32 10-1
335
EBARA Stainless Steel Vertical Multistage EVMU32 5HP - 40HP 3500RPM 3500RPM 150# ANSI 21/2'' 4-Bolt 300# ANSI 21/2'' 8-Bolt
1100
H (m)
304
H (ft)
1000
EVMU
32 10
-1 40 HP Min. Flow
274
900
EVMU
32 9 4 0HP
244
800
EVMU3
213
700
183
600
EVMU32 6 25 HP
EVMU32 5 20HP
152
500
122
400
20
91
300
15
4.5
61
200
10
30
100
EVMU32 1 5HP
NPSH
1.5
0 200
US GPM
0
80 70 60
14
18
23
27
32
36
41
45
Q m3/h
eff. %
810
rev. 03/07
NPSH (m)
NPSH (ft)
EVMU
Model EVMUG / EVMUL Performance Curves EVMU45 1-1 EVMU45 3 EVMU45 4-1 EVMU45 7-2
274
EBARA Stainless Steel Vertical Multistage EVMU45 7.5HP - 50HP 3500RPM 3500RPM 150# ANSI 3'' 4-Bolt 300# ANSI 3'' 8-Bolt
900
H (m)
244
H (ft)
800
EVMU45
7-2 50H P
Min. Flow
EVMU45 6 50H P
213
700
EVMU45 5 40HP
183
600
152
500
EVMU45 4-1
30HP
20
6
122
400
EVMU45 3 25HP
EVMU45 3-2
91
300
20HP
15
4.5
EVMU45 2-1 15
61
HP
10
3
200
EVMU45 1 10HP
30
NPSH (ft)
NPSH
5
100
1.5
0 300 US GPM
68
0
90 80 70 60 50 40 30 20 10 0 0
11
13
34
45
57
Q m3/h
eff. %
50
100
150
200
250
300
811
rev. 03/07
NPSH (m)
EVMU
Model EVMUG / EVMUL Performance Curves EVMU64 1-1 EVMU64 4 EBARA Stainless Steel Vertical Multistage EVMU64 10HP - 50HP 3500RPM 300# 4'' ANSI 8-Bolt
183
600
H (m)
152
H (ft)
EVMU64 4
50HP
Min. Flow
500 EVMU64
4-2 40HP
122
400
EVMU64 3 40 HP
EVMU64 3-2 30 HP
91
300
EVMU64 2
200
20
6 4.5
15
NPSH
0
1.5 0
0 450 US GPM
102
0
90 80 70 60 50 40 30 20 10 0 0
11
13
34
45
57
68
80
91
Q m3/h
eff. %
50
100
150
200
250
300
350
400
450 US GPM
rev. 03/07
NPSH (m)
812
100
10
EVMU
Model EVMU / EVMUG / EVMUL Technical Information Maximum Working Pressure Model EVMU3 2 EVMU5 2 EVMU10 2 EVMU18 2 EVMU32 1 EVMU45 1-1 EVMU64 1-1 EVMU3 11 EVMU5 11 EVMU10 10 EVMU18 7 EVMU32 5 EVMU45 4-1 EVMU64 4-2 EVMU32 9 EVMU3 9 EVMU5 10 EVMU10 8 EVMU18 6 EVMU32 4-3 EVMU45 3 EVMU64 3 EVMU3 18 EVMU5 16 EVMU10 16 EVMU18 11 EVMU32 8-3 EVMU45 7-2 EVMU64 4 EVMU32 10-1 Maximum Working Pressure EBARA Stainless Steel Vertical Multistage
232 PSI
370 PSI
440 PSI
813
rev. 01/08
EVMU
Model EVMU / EVMUL Dimensions Mechanical Seal EVMU 3, 5, 10, 18 EVMUL 3, 5, 10, 18 EBARA Stainless Steel Vertical Multistage
Mechanical Seal
Pump Type
D1 L1 L2 Size Max.working d L [inch] pressure [inch] [inch] [inch] [inch] [inch] [PSI]
Material
1 stationary seal ring 2 3 rotary elastomer seal ring
3-5 10 18
0.63
814
rev. 01/08
EVMU
Model EVMUG / EVMUL Dimensions Mechanical Seal EVMUG 32, 45, 64 EVMUL 32, 45, 64 EBARA Stainless Steel Vertical Multistage
Max. Material working B A Size pressure d d4 L1 L2 L3 L4 L5 d3 d2 d1 stationary rotary (inch) (psi) (inch) (inch) (inch) (inch) (inch) (inch) (inch) (inch) (inch) (inch) seal ring seal ring elastomer
1.102
0.984 1.102
Carbon Silicon 1.535 1.043 0.492 1.693 2.047 2.894 graphite Carbide 1.299 1.969 1.516 0.453 1.181
FPM
815
rev. 01/08
EVMU
Model EVMU / EVMUL Dimensions Models EVMU(L)3 EVMU(L)5 Approximate Motor Dimensions C* for 3 phase, TEFC, NEMA Motors
HP 0.5 0.75 1 1.5 2 3 5 7.5 Frame Size 56C 56C 56C 143TC 145TC 145TC 184TC 184TC C* Inches 9.29 9.29 9.29 9.92 10.08 11.18 13.80 15.30 Motor Wt LBS. 19 21 23 30 33 45 69 88
C*
816
rev. 03/07
EVMU
Model EVMU / EVMUL Dimensions Models EVMU(L)3 EVMU(L)5 EBARA Stainless Steel Vertical Multistage
Motor Frame 56C 56C 56C 143TC 143TC 145TC 145TC 145TC 145TC 145TC 145TC 184TC 184TC 56C 143TC 145TC 145TC 145TC 145TC 145TC 184TC 184TC 184TC 184TC 184TC
Dimensions D 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" 1 3/8" D1 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" 2 63/64" D2 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" 5 33/64" D3 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 9 1/16" 9 1/16" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 6 39/64" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" H 11 5/16" 12 9/64" 12 31/32" 13 55/64" 14 11/16" 15 17/32" 16 23/64" 17 3/16" 18 27/32" 19 43/64" 20 57/64" 22 57/64" 25 3/8" 11 7/8" 13 1/32" 14 9/64" 15 15/64" 16 23/64" 17 55/64" 18 61/64" 21 33/64" 22 5/8" 23 23/32" 25 59/64" 28 5/32" H1
23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32"
Weight [lbs]
38.2 39.2 40.3 41.4 43.5 43.9 44.3 45.9 44.6 46.1 49.1 55.6 63.5 41.7 42.8 44.8 46.1 47.4 49.2 50.5 55.8 58.2 59.7 64.8 67.7
817
rev. 03/07
EVMU
Model EVMU / EVMUL Dimensions Models EVMU(L)10 EVMU(L)18 Approximate Motor Dimensions C* for 3 phase, TEFC, NEMA Motors
HP 1.5 3 5 7.5 7.5 10 15 20 25 Frame Size 143TC 145TC 184TC 184TC 213TC 215TC 215TC 256TC 284TSC C* Inches 9.92 11.18 13.80 15.30 15.18 15.26 16.39 16.32 19.03 Motor Wt LBS. 30 45 69 88 99 122 143 221 371
C*
818
rev. 03/07
EVMU
Model EVMU / EVMUL Dimensions Models EVMU(L)10 EVMU(L)18
Pump Type EVMU(L) 10 10 10 10 10 10 10 10 10 10 18 18 18 18 18 18 18 18 18 2 3 4 5 6 8 10 12 14 16 2 3 4 5 6 7 8 10 11 Motor Frame 143TC 145TC 145TC 184TC 184TC 184TC 213TC 215TC 215TC 215TC 184TC 184TC 184TC 215TC 215TC 215TC 215TC 256TC 284TSC Dimensions D1 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" 4 1/64" D3 6 39/64" 6 39/64" 6 39/64" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 9 1/16" 11 1/32" H 14 1/64" 15 13/64" 16 49/64" 18 13/16" 20" 22 3/8" 24 3/4" 27 7/64" 29 41/64" 32" 15 9/16" 17 41/64" 19 7/32" 20 25/32" 22 9/16" 24 9/64" 25 45/64" 28 55/64" 30 37/64" H1
23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32" 23/32"
Weight [lbs]
130.9 138.2 149.8 152.8 160.1 192.1 196.6 242.2 254.3 279.1 182.9 190.2 190.2 236.4 258.8 271.0 278.3 329.3 336.6
819
rev. 03/07
EVMU
Model EVMUG / EVMUL Dimensions Models EVMUL32 1 EVMUL32 4-3 EVMUL45 1-1 EVMUL45 3 EVMUG32 1 EVMUG32 4-3 EVMUG45 1-1 EVMUG45 3 Approximate Motor Dimensions C* for 3 phase, TEFC, NEMA Motors
HP 5 7.5 10 15 20 Frame Size 184TC 184TC 215TC 215TC 256TC C* Inches 13.80 15.30 15.26 16.39 16.32 Motor Wt LBS. 69 88 122 143 221
C*
Flange Detail: EVMU32 21/2" 150Lb. ANSI EVMU45 3" 150Lb. ANSI
820
rev. 03/07
EVMU
Model EVMUG / EVMUL Dimensions Models EVMUG64 1-1 EVMUG64 3 EVMUL64 1-1 EVMUL64 3 EBARA Stainless Steel Vertical Multistage
C*
821
rev. 03/07
EVMU
Model EVMUG / EVMUL Dimensions Models EVMUG32 5 EVMUG32 10-1 EVMUG45 4-1 EVMUG45 7-2 EVMUG64 4-2 EVMUG64 4 EVMUL32 5 EVMUL32 10-1 EVMUL45 4-1 EVMUL45 7-2 EVMUL64 4-2 EVMUL64 4 Approximate Motor Dimensions C* for 3 phase, TEFC, NEMA Motors
HP 20 25 30 40 50 Frame Size 256TC 284TSC 286TSC 324TSC 326TSC C* Inches 16.32 19.03 19.03 23.39 23.39 Motor Wt LBS. 221 371 403 422 962
C*
Flange Detail: EVMU32 21/2" 300Lb. ANSI EVMU45 3" 300Lb. ANSI EVMU64 4" 300Lb. ANSI
822
rev. 03/07
EVMU
Model EVMUG / EVMUL Dimension Table
Pump Type Model HP Weight Motor Lbs. Frame* 117 184TC 5 32 1 7 1/2 126 184TC 32 2-2 170 215TC 10 32 3-2 172 215TC 15 32 3 176 215TC 15 32 4-3 194 256TC 20 32 5 200 284TSC 25 32 6 207 286TSC 30 32 7 225 286TSC 30 32 8-3 240 324TSC 40 32 9 247 324TSC 40 32 10-1 7 1/2 148 184TC 45 1-1 152 215TC 10 45 1 192 215TC 15 45 2-1 207 256TC 20 45 3-2 207 284TSC 25 45 3 229 286TSC 30 45 4-1 260 324TSC 40 45 5 276 326TSC 50 45 6 287 326TSC 50 45 7-2 179 215TC 10 64 1-1 201 215TC 15 64 1 213 256TC 20 64 2-1 214 284TSC 25 64 2 221 286TSC 30 64 3-2 223 324TSC 40 64 3 245 324TSC 40 64 4-2 251 326TSC 50 64 4 Pump Type Model HP 32 1 32 2-2 32 3-2 32 3 32 4-3 32 5 32 6 32 7 32 8-3 32 9 32 10-1 45 1-1 45 1 45 2-1 45 3-2 45 3 45 4-1 45 5 45 6 45 7-2 64 1-1 64 1 64 2-1 64 2 64 3-2 64 3 64 4-2 64 4 5 7 1/2 10 15 15 20 25 30 30 40 40 7 1/2 10 15 20 25 30 40 50 50 10 15 20 25 30 40 40 50 Motor Frame* 184TC 184TC 215TC 215TC 215TC 256TC 284TSC 286TSC 286TSC 324TSC 324TSC 184TC 215TC 215TC 256TC 284TSC 286TSC 324TSC 326TSC 326TSC 215TC 215TC 256TC 284TSC 286TSC 324TSC 324TSC 326TSC SE BM BY1 PL 18 3/16 20 19/32 22 31/64 27 41.64 29 17/32 31 27/64 33 7/64 35 36 57/64 39 3/8 41 17/64 21 29/64 21 29/64 29 29/64 32 9/32 32 2/32 34 59/64 38 11/32 41 3/16 44 1/64 21 29/64 26 5/8 29 29/64 29 1/4 32 3/32 32 11/16 35 33/64 35 33/64 H G
54/64
25/32
4 9/64
12 9/32 1 1/16
2 9/16
7 1/2
25/32
1 13/64
8 1/4
29/32
25/32 8
10
29/32
BF
BH
5 1/2
6 11/16 5 7/8
9 29/64
8 17/64
11 1/32
35/64
1 3/8
6 5/8
7 7/8
Bare Pump only.
*Motor frame for Three Phase TEFC only. Consult factory for single phase and alternate enclosures.
823
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)3 2 EVMU(L)3 12 EBARA Stainless Steel Vertical Multistage
Refer to page 828 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
824
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)3 13 EVMU(L)3 18 EBARA Stainless Steel Vertical Multistage
Refer to page 828 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
825
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)5 2 EVMU(L)5 6 EBARA Stainless Steel Vertical Multistage
Refer to page 828 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
826
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)5 7 EVMU(L)5 16 EBARA Stainless Steel Vertical Multistage
Refer to page 828 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
827
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View part reference Models EVMU(L)3 EVMU(L)5
N Par t n am e EVMU
005-1 005-2 005-3 005-4 006 007 021 031 043-1 043-2 043-3 043-5 043-6 044-1 046 047 048 051 052-1 056 070-1 075 075-1 107 111 111-3 115-1 115-2 115-5 Suction casing Intermediate casing Intermediate casing bearing Discharge casing Bottom casing Outer casing Impeller Shaft Shaft sleeve (mechanical seal) Shaft sleeve (intermediate) Shaft sleeve (bearing) Shaft sleeve (last stage) Shaft sleeve (adjustment) Shaft sleeve bearing Split ring (mechanical seal) Ring holder Impeller nut Motor adapter Bearing Ball bearing Ring for bearing O-ring (plug) O-ring (plug) Liner ring Mechanical seal Mechanical seal seat O-ring (outer casing) O-ring (intermediate casing) O-ring EN 1.4301(AISI 304) FPM FPM PTFE/EN 1.4401 (AISI 316) Silicon carbide/Carbon/FPM EN 1.4301(AISI 304) FPM FPM FPM EN 1.4401 (AISI 316) EN 1.4301(AISI 304) EN 1.4301(AISI 304) A2-70 UNI 7323 with inox insert EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) Tungsten carbide EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) A4-70 UNI 7323 with inox insert
Mat er i al EVMUL
EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316)
828
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View part reference Models EVMU(L)3 EVMU(L)5
N Par t n am e EVMU
120-1 120-3 120-5 120-6 128-1 130-2 130-4 131-1 135-1 135-4 137-1 140 150 160 162 169 212 212-1 245 273 273-1 274-2 274-3 Tie rod Screw Screw for coupling Screw for coupling Nut for tie rod Screw for coupling guard Set-screw Pin for shaft Washer Washer (bearing) Impeller spacer Coupling Spacer Base Motor bracket Motor adapter Plug Plug Coupling guard Washer (plug) Washer (plug) C-type snap ring (coupling) C-type snap ring (bracket) EVMU3 13, EVMU5 7 ,8 EVMU3 15, 18, EVMU5 10 to 16 EVMU3 13, EVMU5 7 ,8 EVMU3 15, 18, EVMU5 10 to 16 EN 1.4301(AISI 304) Carbon steel Cast iron EN-GJL-200-EN 1561 Cast iron EN-GJL-200-EN 1561+ EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) Cast iron + EN 1.4401 (AISI 316) Zincate steel A2-70 UNI 7323 Zincate steel 8.8 strenght class ISO 898/1 Zincate steel 8.8 strength class ISO 898/1 Zincate steel 8.8 strenght class ISO 898/1 Zincate steel 8.8 strength class ISO 898/1 Zincate steel A2-70 UNI 7323 Carbon steel Carbon steel Zincate steel Carbon steel EN 1.4401 (AISI 316) Brass OT 58 UNI 5705
Mat er i al EVMUL
Cast iron EN-GJL-200-EN 1561 EN 1.4401 (AISI 316) EN 1.4401 (AISI 316)
EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) Carbon steel TC 80 Carbon steel TC 80 EN 1.4401 (AISI 316) /
829
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)10 2 EVMU(L)10 3 EBARA Stainless Steel Vertical Multistage
Refer to page 836 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
830
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)10 4 EVMU(L)10 12 EBARA Stainless Steel Vertical Multistage
Refer to page 836 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
831
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)10 14 EVMU(L)10 16 EBARA Stainless Steel Vertical Multistage
Refer to page 836 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
832
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)18 2 EBARA Stainless Steel Vertical Multistage
Refer to page 838 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
833
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)18 3 EVMU(L)18 5 EBARA Stainless Steel Vertical Multistage
Refer to page 838 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
834
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View Models EVMU(L)18 6 EVMU(L)18 11 EBARA Stainless Steel Vertical Multistage
Refer to page 838 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
835
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View part reference Model
N
EVMU(L)10
Par t n am e EVMU Mat er i al EVML
EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) Tungsten carbide EN 1.4301(AISI 304) EN 1.4301(AISI 304) A2-70 UNI 7323 with inox insert EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) A4-70 UNI 7323 with inox insert
005-1 005-2 005-3 005-4 006 007 021 031 043-1 043-2 043-3 043-5 043-6 044-1 046 047 048 051 052-1 056 070-1 075 075-1 107 111 111-3 115-1 115-2 115-5
Suction casing Intermediate casing Intermediate casing bearing Discharge casing Bottom casing Outer casing Impeller Shaft Shaft sleeve (mechanical seal) Shaft sleeve (intermediate) Shaft sleeve (bearing) Shaft sleeve (last stage) Shaft sleeve (adjustment) Shaft sleeve bearing Split ring (mechanical seal) Ring holder Impeller nut Motor adapter Bearing Ball bearing Ring for bearing O-ring (plug) O-ring (plug) Liner ring Mechanical seal Mechanical seal seat O-ring (outer casing) O-ring (intermediate casing) O-ring
Cast iron EN-GJL-200-EN 1561 Tungsten carbide See table pag. 500 EN 1.4301(AISI 304) FPM FPM PTFE/EN 1.4401 (AISI 316) Silicon carbide/Carbon/FPM EN 1.4301(AISI 304) FPM FPM FPM EN 1.4401 (AISI 316) /
836
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View part reference Model EVMU(L)10 EBARA Stainless Steel Vertical Multistage
Par t n am e EVMU
Mat er i al EVML
Zincate steel A2-70 UNI 7323 Zincate steel 8.8 strenght class ISO 898/1 Zincate steel 8.8 strength class ISO 898/1
120-1 120-3 120-5 120-6 120-7 128-1 130-2 130-4 131-1 135-1 135-4 137-1 140 150 160 162 169 212 212-1 245 273 273-1 274-1
Tie rod Screw Screw for coupling EVMU10 2, EVMU10 3 Screw for coupling Screw (bearing) Nut for tie rod Screw for coupling guard Set-screw Pin for shaft Washer Washer (bearing) Impeller spacer Coupling Spacer Base Motor bracket Motor adapter Plug Plug Coupling guard Washer (plug) Washer (plug) C-type snap ring (coupling) EVMU10 4 EVMU10 5 to 8 EVMU10 10 to 12 EVMU10 14 to16 EVMU10 4 / EN 1.4301(AISI 304) EVMU10 4 to12 EVMU10 14 to16
Zincate steel 8.8 trenght lass I ISO 898/1 Zincate steel 8.8 sstrengthcclass SO 898/1
Zincate steel 8.8 strenght class ISO 898/1 Zincate steel 8.8 strength class ISO 898/1 Zincate steel A2-70 UNI 7323 Carbon steel Carbon steel Zincate steel Carbon steel EN 1.4401 (AISI 316) Carbon steel Cast iron EN-GJL-200-EN 1561 Cast iron + EN 1.4401 (AISI 316) Cast iron EN-GJL-200-EN 1561+ EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) Brass OT 58 UNI 5705
Cast iron EN-GJL-200-EN 1561 EN 1.4401 (AISI 316) EN 1.4401 (AISI 316)
EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4401 (AISI 316) / EN 1.4401 (AISI 316)
274-2
Carbon steel TC 80
274-3
EVMU10 5 to 8 EVMU10 10 to 12
Carbon steel TC 80
837
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View part reference Model
N
EVMU(L)18
Par t n am e EVMU Mat er i al EVML
EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) Tungsten carbide EN 1.4301(AISI 304) EN 1.4301(AISI 304) A2-70 UNI 7323 with inox insert EN 1.4401 (AISI 316) EN 1.4401 (AISI 316) A4-70 UNI 7323 with inox insert
005-1 005-2 005-3 005-4 006 007 021 031 043-1 043-2 043-3 043-5 043-6 044-1 046 047 048 051 052-1 056 070-1 075 075-1 107 111 111-3 115-1 115-2 115-5
Suction casing Intermediate casing Intermediate casing bearing Discharge casing Bottom casing Outer casing Impeller Shaft Shaft sleeve (mechanical seal) Shaft sleeve (intermediate) Shaft sleeve (bearing) Shaft sleeve (last stage) Shaft sleeve (adjustment) Shaft sleeve bearing Split ring (mechanical seal) Ring holder Impeller nut Motor adapter Bearing Ball bearing Ring for bearing O-ring (plug) O-ring (plug) Liner ring Mechanical seal Mechanical seal seat O-ring (outer casing) O-ring (intermediate casing) O-ring
Cast iron EN-GJL-200-EN 1561 Tungsten carbide See table pag. 500 EN 1.4301(AISI 304) FPM FPM PTFE/EN 1.4401 (AISI 316) Silicon carbide/Carbon/FPM EN 1.4301(AISI 304) FPM FPM FPM EN 1.4401 (AISI 316) /
838
rev. 03/07
EVMU
Model EVMU / EVMUL Sectional View part reference Model
N
EVMU(L)10
Par t n am e EVMU Mat er i al EVML
Zincate steel A2-70 UNI 7323
120-1 120-3 120-5 120-6 120-7 128-1 130-2 130-4 131-1 135-1 135-4 137-1 140 150 160 162 169 212 212-1 245 273 273-1 274-1
Tie rod Screw Screw for coupling EVMU18 2 Screw for coupling Screw (bearing) Nut for tie rod Screw for coupling guard Set-screw Pin for shaft Washer Washer (bearing) Impeller spacer Coupling Spacer Base Motor bracket Motor adapter Plug Plug Coupling guard Washer (plug) Washer (plug) C-type snap ring (coupling) EVMU18 3 to 4 EVMU18 5 EVMU18 6 to 10 EVMU18 11 EVMU18 3 to 4 EVMU18 5 EN 1.4301(AISI 304) EVMU18 3 to 5 EVMU18 6 to 11
Zincate steel 8.8 strenght class ISO 898/1 strength class ISO 898/1 Zincate steel 8.8 strenght class IISO898/1 Zincate steel 8.8 strength class SO 898/1 Zincate steel 8.8 strenght class ISO 898/1 strength class ISO 898/1 Zincate steel
A2-70 UNI 7323 Carbon steel Carbon steel Zincate steel Carbon steel EN 1.4401 (AISI 316) Carbon steel Cast iron EN-GJL-200-EN 1561 Cast iron EN-GJL-200-EN 1561+ EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) Cast iron + EN 1.4401 (AISI 316) Brass OT 58 UNI 5705
Cast iron EN-GJL-200-EN 1561 EN 1.4401 (AISI 316) EN 1.4401 (AISI 316)
EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4301(AISI 304) EN 1.4401 (AISI 316) / EN 1.4401 (AISI 316)
274-2
Carbon steel TC 80
274-3
Carbon steel TC 80
839
rev. 03/07
EVMU
Model EVMUG / EVMUL Sectional View Model EVMUG32 EVMUL32 EBARA Stainless Steel Vertical Multistage
Refer to page 841 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
840
rev. 03/07
EVMU
Model EVMUG / EVMUL Sectional View part reference Model EVMUG32 EVMUL32
N O. 0 0 5 -1 0 0 5 -2 0 0 5 -3 0 0 5 -4 006 007 011 021 031 0 3 9 -1 0 4 3 -1 0 4 3 -2 0 4 3 -3 0 4 3 -4 0 4 3 -5 0 4 4 -1 045 047 048 051 0 5 2 -1 056 070-1 107 111 1 1 5 -1 1 1 5 -2 1 2 0 -1 1 2 0 -3 1 2 0 -4 1 2 0 -5 1 2 0 -6 1 2 0 -7 1 2 0 -8 1 2 0 -1 0 1 2 8 -1 1 3 0 -1 1 3 0 -2 1 3 0 -3 1 3 0 -4 1 3 1 -1 1 3 5 -1 1 3 5 -3 1 3 5 -4 1 3 7 -1 1 4 0 -1 1 4 0 -2 150 160 163 169 212 217 245 2 7 4 -1 2 7 4 -2 613 P A R T N AME S t a g e c a s in g S t a g e c a s in g S t a g e c a s in g S t a g e c a s in g B o t t o m c a s in g O u t e r s le e v e C a s in g c o v e r I m p e lle r Shaf t Key S h a f t s le e v e S h a f t s le e v e S h a f t s le e v e S h a f t s le e v e S h a f t s le e v e B e a ri n g s le e v e Adjusting ring S p l it r in g r e t a in e r F r ic t i o n n u t Bearing housing B e a ri n g Ball bearing Bearing holder W ear ring Mec ha nic al s e al O - r in g O - r in g Tie-rod bolt B o lt B o lt B o lt B o lt B o lt B o lt B o lt N ut S c re w S c re w S c re w S c re w P in W as h er Spring was her Spring was her S h a f t e n d s le e v e C o u p l in g u p p e r h a lf C oupling lower half Spa c er Base plate Motor stool Motor liner V e n t p lu g P lu g Coupling guard C - r in g C - r in g Pum p f lange ( s u c t io n ) ( b e a r in g ) (Top) MATER IAL E V MUG AI S I 304 AI S I 304 AI S I 304 AI S I 304 C a s t i ro n E N - G J L - 2 5 0 AI S I 304 C a s t ir o n E N - G J S - 4 0 0 - 1 5 AI S I 304 AISI316 C 45 AI S I 304 AI S I 304 AI S I 304 AI S I 304 AI S I 304 Tung s t en c arbide C40 AI S I 304 AI S I 304 (s t a g e ) A I SI 31 6 A I SI 31 6 A I SI 31 6 A I SI 31 6 A I SI 31 6 A I SI 31 6 A I SI 31 6 EV MUL A I SI 31 6 A I SI 31 6 A I SI 31 6 A I SI 31 6 C a s t A I S I 316 (G -X6C rN iMo18 0) A I SI 31 6 C as t iro n EN -G J S -400-15+A I S I 304 A I SI 31 6
( c o u p l in g ) ( m e c h a n ic a l s e a l) (s t a g e ) ( b e a r in g / u p p e r ) (bearin g/ lower) (t o p ) (s t a g e )
( c o u p l in g )
Cast iron EN -GJL-200 Tung s t en c arbide AISI304 AISI316+PTFE S iC / C arbon/ F P M/ 316 F PM F PM Z inc at e s t eel wit h 6. 8 s t rengt h c la s s I SO 898/ 1 S t a i n le s s s t e e l A 2 -7 0 I S O 3 5 0 6 S t a i n le s s s t e e l A 2 -7 0 I S O 3 5 0 6 Z inc at e s t eel wit h 8. 8 s t rengt h c la s s I SO 898/ 1 Z inc at e s t eel wit h 8. 8 s t rengt h c la s s I SO 898/ 1 Z inc at e s t eel wit h 8. 8 s t rengt h c la s s I SO 898/ 1 Z inc at e s t eel wit h 8. 8 s t rengt h c la s s I SO 898/ 1 Z inc at e s t eel wit h 8. 8 s t rengt h c la s s I SO 898/ 1 Z inc at e s t eel wit h 6S s t reng t h c las s I S O 898/ 2 S t a i n le s s s t e e l A 2 -7 0 I S O 3 5 0 6 S t a i n le s s s t e e l A 2 -7 0 I S O 3 5 0 6 S t a i n le s s s t e e l A 2 -7 0 I S O 3 5 0 6 S t re n g t h c la s s 4 5 H I S O 8 9 8 / 5 C F 35 SMnP b10 Z in c a t e s t e e l Z in c a t e s t e e l Z in c a t e s t e e l AI S I 304 A I SI 31 6 St eel (36S MnP b14) St eel (36S MnP b14) C 45 Cast iron EN -GJL-200 Cast iron EN -GJL-200 Cast iron EN -GJL-200 AI S I 304/ F P M A I SI 3 16/ F P M AI S I 304/ F P M A I SI 3 16/ F P M AISI304 AI S I 304 A I SI 31 6 C arbon t oo l s t eel (TC 8 0) C40
841
rev. 03/07
EVMU
Model EVMUG / EVMUL Sectional View Models EVMUG45 EVMUG64 EVMUL45 EVMUL64
Coupling Detail for Models EVMU45 1-1 - EVMU45 1 EVMU64 1-1
Refer to page 843 for material details. (For reference only. See pricing for part availability.)
EBARA Fluid Handling www.pumpsebara.com
(t) 803 327-5005 (f) 803 327-5097
842
rev. 03/07
EVMU
Model EVMUG / EVMUL Sectional View part reference Model EVMUG45 EVMUG64 EVMUL45 EVMUL64
N O. 005-2 005-4 006 007 011 012 021 031 0 3 9 -1 0 4 3 -1 0 4 3 -2 0 4 3 -3 0 4 3 -4 0 4 3 -5 0 4 3 -6 0 4 3 -7 044-1 0 4 4 -2 045 047 048 051 0 5 2 -1 0 5 2 -2 053 056 070-1 0 7 0 -2 081 107 111 1 1 5 -1 1 1 5 -2 120-1 120-2 1 2 0 -3 1 2 0 -4 1 2 0 -5 1 2 0 -6 1 2 0 -7 1 2 0 -8 1 2 0 -9 1 2 0 -1 2 1 2 8 -1 1 2 8 -2 129 1 3 0 -1 1 3 0 -2 1 3 0 -3 1 3 0 -4 1 3 1 -1 1 3 5 -1 1 3 5 -2 1 3 5 -3 135-4 1 3 5 -5 136 137-1 137-2 140-1 140-2 163 212 217 245 2 7 4 -1 613 Stage c asing T op c as ing Bottom c as ing Outer s leeve C a s i n g c o ve r Suc tion cover Impeller Shaft K ey S h a ft s l e e ve S h a ft s l e e ve S h a ft s l e e ve S h a ft s l e e ve S h a ft s l e e ve S h a ft s l e e ve S h a ft s l e e ve Bearing sleeve B e a ri n g s l e e ve Adjus ting ring Split ring retainer Fric tion nut Bearing hous ing B e a ri n g B e a ri n g Bus h holder Ball bearing Bearing holder B e a ri n g h o l d e r Bus h W ear ring Me c h a n i c a l s e a l O-ri n g O-ri n g T ie-rod bolt Stack bolt B ol t B ol t B ol t B ol t B ol t B ol t B ol t B ol t Nu t Nu t Bearing nut S c re w S c re w S c re w S c re w Pin W as her S p ri n g w a s h e r S p ri n g w a s h e r Spring was her S p ri n g w a s h e r Bearing was her Shaft end s leeve Shaft end s leeve Coupling upper half Coupling lower half Motor s tool V ent pl ug P l ug Coupling guard C -ri n g Pump flange (to p ) A IS I3 0 4 C40 (wi th s e a l ri n g ) (wi th s e a l ri n g ) A IS I3 0 4 /FP M A IS I3 0 4 /FP M AISI304 A IS I3 1 6 (m e c h a n i c a l s e a l ) (c a s i n g c o ve r) (c o u p l i n g M-s i d e ) (c o u p l i n g P -s i d e ) (b e a ri n g ) (b e a ri n g h o u s i n g ) (b o tto m b e a ri n g ) (s h a ft e n d ) (ti e -ro d b o l t) (S ta c k b o l t) (coupling) (m e c h a n i c a l s e a l ) (c o u p l i n g g u a rd ) (m e c h a n i c a l s e a l ) (c o u p l i n g p i n ) (s h a ft) (ti e -ro d b o l t) (S ta c k b o l t) (c o u p l i n g b o l t M-s i d e ) (bearing) (s h a ft e n d ) (coupling) A IS I3 0 4 A IS I3 0 4 Steel (36SMnPb14) Steel (36SMnPb14) Cas t iron EN-GJ L-200 A IS I3 1 6 /FP M A IS I3 1 6 /FP M A IS I3 0 4 Carbon s teel A IS I3 1 6 A IS I3 1 6 A IS I3 0 4 Zi n c a te s te e l Zinc ate s teel A IS I3 1 6 A IS I3 0 4 Carbon s teel S ta i n l e s s s te e l A 2 -7 0 IS O3 5 0 6 S ta i n l e s s s te e l A 2 -7 0 IS O3 5 0 6 S ta i n l e s s s te e l A 2 -7 0 IS O3 5 0 6 S tre n g th c l a s s 4 5 H IS O8 9 8 /5 CF35SMnPb10 Zinc ate s teel A IS I3 1 6 A IS I3 0 4 S ta i n l e s s s te e l A 2 -7 0 IS O3 5 0 6 S ta i n l e s s s te e l A 2 -7 0 IS O3 5 0 6 Zi n c a te s te e l w i th 8 .8 s tre n g th c l a s s IS O 8 9 8 /1 Zi n c a te s te e l w i th 8 .8 s tre n g th c l a s s IS O 8 9 8 /1 Zi n c a te s te e l w i th 8 .8 s tre n g th c l a s s IS O 8 9 8 /1 Zi n c a te s te e l w i th 8 .8 s tre n g th c l a s s IS O 8 9 8 /1 S ta i n l e s s s te e l A 2 -7 0 IS O3 5 0 6 S ta i n l e s s s te e l A 2 -7 0 IS O3 5 0 6 Zi n c a te s te e l w i th 6 S s tre n g th c l a s s IS O 8 9 8 /2 Ca rtri d g e a s s 'y (o u te r) (s ta g e ) (b o tto m b e a ri n g ) A IS I3 0 4 PT FE(alloy) AISI316+PT FE S i C /C a rb o n /FP M/3 1 6 FPM FPM Zinc ate s teel with 6.8 strength c las s ISO 898/1 A IS I3 1 6 (s ta g e ) (b o tto m ) A IS I3 0 4 AISI304 A IS I3 1 6 A IS I3 0 4 A IS I3 0 4 Cas t iron EN-GJ L-200 T ungs ten c arbide T ungs ten c arbide A IS I3 1 6 (c o u p l i n g ) (m e c h a n i c a l s e a l ) (s ta g e ) (b e a ri n g /u p p e r) (b e a ri n g /l o we r) (to p ) (s u c ti o n ) (b o tto m b e a ri n g ) (stage) (b o tto m b e a ri n g ) A IS I3 0 4 A IS I3 0 4 A IS I3 0 4 A IS I3 0 4 A IS I3 0 4 A IS I3 0 4 A IS I3 0 4 T ungs ten c arbide T u n g s te n c a rb i d e C40 A IS I3 1 6 A IS I3 1 6 P A R T N A ME MAT ERIAL E V MUG A IS I3 0 4 A IS I3 0 4 16bar:Cas t iron EN-GJ L-250 25bar:Cas t iron EN-GJ S-400-15 A IS I3 0 4 C a s t i ro n E N -GJ S -4 0 0 -1 5 A IS I3 0 4 A IS I3 0 4 AISI316 C45 A IS I3 1 6 A IS I3 1 6 A IS I3 1 6 A IS I3 1 6 A IS I3 1 6 A IS I3 1 6 A IS I3 1 6 E V MUL A IS I3 1 6 A IS I3 1 6 Cas t AISI316 (G-X6CrNiMo18 0) A IS I3 1 6 C a s t i ro n E N-GJ S -4 0 0 -1 5 +A IS I3 1 6 A IS I3 1 6 A IS I3 1 6
EBARA Stainless Steel Vertical Multistage (See pricing for part availability.)
843
rev. 03/07