Académique Documents
Professionnel Documents
Culture Documents
Service guide files and updates are available on the CSD web : for more information, Please refer to http: csd.acer.com.tw
Table of Contents
Chapter 1 Monitor Features.. 8
1.1 1.2 1.3 1.4 Test conditions.. 8 Features..... 8 LCD Panel specification... 9 Connector Pin Assignment........12
Chapter 4 Troubleshooting.....27
4.1 Abnormal display Troubleshooting.27 4.2 Abnormal (On/Off, LCD Display, K/B) Troubleshooting..29 4.3 Abnormal (BIOS, OSD, Other Display) Troubleshooting30 4.4 Audio Abnormal.....31
Chapter 1
Monitor Features
1.1 Test Conditions
Item Condition Temperature Normal room temperature (25 2J ) Humidity 50 10% AC input voltage 100V 2V, 120 2V, 60Hz / 230 2V, 50Hz Signal Level 0.7Vp-p Brightness Maximum with OSD setting Contrast Middle with OSD setting Resolution setting 1024 x 768 @60HZ Color temperature With OSD setting Measuring instrument Topcon luminance colorimeter BM-5A or equivalent Others Before measuring, Auto Config & Auto Balance must be done in advance
1.2 Features
15 XGA TFT LCD Panel TN Mode Liquid Crystal D-SUB Input Audio Function (Optional) Support to 75Hz Refresh Rate Support VESA-DCC 2B plug & play function Support VESA-DPMS Power Management Function Wide Viewing Angle High Brightness High Brightness & Contrast Angular Dependent Fast LC Response Time Light Weight
yX- = 90 xx-
y+ y+ x+ 12 oclock direction y+ = 90
6 oclock y- = 90
y-
x+
X+ = 90
Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression and figure below. Contrast Ratio (CR) = L255 / L0 L255: Luminance of gray level 255 L 0: Luminance of gray level 0 CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (5). Definition of luminance measured points and Brightness Uniformity:
1 5 3
2 X : test point
X=1 to 5
4
767
Active area
10
Luminance of center point: L=L(5) Brightness Uniformity Measurement points: Five specified points 1-5 Formula: Maximum [L (1), L (2), L (3), L (4), L (5)]/Minimum [L (1), L (2), L (3), L (4), L (5)] Note (3) Definition of Response Time (TR, TF):
Gray Level 255
100% 90%
Gray Level 0
TR
TF
Time
Note (4) Measurement Setup: The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room.
LCD Module LCD Panel Center of the Screen Photometer (TOPCON BM-5A)
Field of View = 2
Light Shield Room (Ambient Luminance < 2 lux)
500 mm
11
Pin No. 1 2 3 4 5 6 7 8
Pin Function Red video input Green video input Blue video input NC Ground Red video ground Green video ground Blue video ground
Pin Function
1.4.2 DC Connector
12
13
Chapter 2
Operating Instructions
2.1 Function Names
2.1.1 Front
No. 1 2
Descriptions
3 4 5 6 7
OSD control MENU button Right selection/ Volume button (AL1512m) Left selection/ Volume button (AL1512m) Adjust Clock, Phase, H Position and V Position automatically 1.5W x 2
14
2.1.2 Back
No. 8 9 10 11
Name AUDIO-IN VGA-IN DC-IN Lock hole d=3.5mm stereo mini Jack D-sub mini 15pin Connector DC Power Jack, d=2.0mm. Kinglock
Descriptions
15
2.2 OSD Menu Description 1. Power : Press this key to control power ON/OFF of the Monitor. Green: Power is on and normal . Orange: Power off. Orange Sleep status in the energy-saving mode. 2. Menu : Press this button to enter OSD. Press it again to exit OSD. 3. > / Plus and < / Minus : Press this button for selection or adjustment when OSD is shown. Press this button and click < and > to adjust volume when OSD is not shown (for the model with speakers only) 4. Auto : Press this button to exit the manual when OSD is shown. Press this button for the display to optimize the position, phase and clock pulse automatically when OSD is not shown.
Auto
<
>
Menu
LED
Power
16
Click MENU to display the OSD window as shown in the following figure. Click < or > to select the function to be adjusted as shown in the following figure. Click the MENU to select the function to be adjusted. Click < or > to change current settings. To exit OSD, select to close the OSD window and save changes. To change other settings repeat steps 2-4. .
Bright/Contract Adjustment Phase/Clock pulse Adjustment Horizontal/Vertical Adjustment Color Temp. Adjustment Language Selection
17
Vertical
Move the image up and down on the screen (for input adjustment only)
N/A N/A
N/A N/A
Warm Color Set up the color temp. to be warm white color Temp. Cold Color Set up the color temp. to be cold white color Temp. User Definition/Red User Adjust red/green/blue gain Definition/Green User Definition/Blue English Select the language you want
c (Complex Chinese) Deutsch Franais Espaol Italiano (Simplified Chinese) y (Japanese)
N/A
Horizontal Move OSD left and right Vertical OSD Time Display Auto Adjustment Move OSD up and down Adjust OSD time display settings Set up horizontal, vertical, sequence and focus automatically
N/A
18
N/A
Message
Display resolution, H/V frequency and the input port used for current input timing function. Restore to factory settings Close the OSD window and save changes.
N/A N/A
Restore Exit
2.5 Plug and Play The product provides the latest VESA plug and play function to prevent complicated and time-consuming installation procedures. The plug and play function allows your computer system to identify the LCD display easily and set up the functions of the LCD display automatically. The LCD display transfers the Extended Display Identification Data (EDID) to your computer system via the Display Data Channel (DDC), so that your computer can use the self-setting function of the LCD display.
2.6 Power Saver The LCD display has a built-in Power Control System (Power Saver). When the LCD display is not operated during a certain time, the Power Control System will brings the LCD display into low voltage status automatically to save power. Move the mouse slightly or press any key to return to the normal operation. The Power Saver function can only be operated by the display card of the computer system. You can set up this function from your computer. The LCD display is compatible with EPAENERGY STAR NTEK when used with VESA DPMS To save power and extend the life of the product, turn off the LCD display power supply when it is not used or when remaining idle for a long time.
19
Chapter 3
Picture
Description
Push the hooks and stand bottom away
20
21
Lift up Inverter slightly, and Separate its head from the housing at AD PCBA
Remove AD PCBA
22
Fasten 2 screws
23
Fasten 4 screws
Shift Inverter with care ; plug its head into the housing at AD PCBA
24
Push the metal Cover (PCB-X) andforward to have the hook latched.
Fasten 3 screws
Fasten 5 screws
25
26
Chapter 4
Troubleshooting
4.1 Abnormal Display Troubleshooting
27
28
29
30
31
Chapter 5
Connector Information
5.1 Function block Diagram
OSD Key
3.3V Main D-sub Analog Video DC/D DC12V DC -12V Inverter Backlight Signal LCD
32
CN5
JP1
CN4
CN2
CN3
33
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Symbol STV1 OE CKV GND STH1 REV1 REV2 POL STB GND CKH GND GMA1 GMA2 GMA3 GMA4 GMA5 GMA6 GMA7 GMA8 GMA9 GMA10 GND VCOM VCOM VCOM VCOM VCOM VSA VSA VSA VSA VSA
Description SCAN IC START PULSE SCAN DATA OUTPUT ENABLE SCAN IC CLOCK GROUND SHIFT START PULSE I/O DATA INVERSION INPUT DATA INVERSION INPUT POLARITH INVERTING DATA LATCH GROUND DATA CLOCK INPUT GROUND GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GAMMA VOLTAGE GROUND PANEL COMMOM VOLTAGE PANEL COMMOM VOLTAGE PANEL COMMOM VOLTAGE PANEL COMMOM VOLTAGE PANEL COMMOM VOLTAGE DRIVER SUPPLY VOLTAGE DRIVER SUPPLY VOLTAGE DRIVER SUPPLY VOLTAGE DRIVER SUPPLY VOLTAGE DRIVER SUPPLY VOLTAGE
34
34 35 36 37 38 39 40 41 42 43 44 45
VSD VSD VSD VDDY VDDY DRESTOUT PANEL VGL PANEL VGL GND PANEL VGH PANEL VGH GND
DATA IC VOLTAGE DATA IC VOLTAGE DATA IC VOLTAGE DRIVER SUPPLY VOLTAGE DRIVER SUPPLY VOLTAGE OUTPUT ALL-ON CONTROL PANEL DRIVING VOLTAGE PANEL DRIVING VOLTAGE GROUND PANEL DRIVING VOLTAGE PANEL DRIVING VOLTAGE GROUND
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Symbol GND GND ER0 ER1 ER2 ER3 ER4 ER5 GND EG0 EG1 EG2 EG3 EG4 EG5 GND EB0 EB1 EB2 EB3 EB4 EB5 GND
35
Description GROUND GROUND EVEN PATH RED DATA BIT EVEN PATH RED DATA BIT EVEN PATH RED DATA BIT EVEN PATH RED DATA BIT EVEN PATH RED DATA BIT EVEN PATH RED DATA BIT GROUND EVEN PATH GREEN DATA BIT EVEN PATH GREEN DATA BIT EVEN PATH GREEN DATA BIT EVEN PATH GREEN DATA BIT EVEN PATH GREEN DATA BIT EVEN PATH GREEN DATA BIT GROUND EVEN PATH BLUE DATA BIT EVEN PATH BLUE DATA BIT EVEN PATH BLUE DATA BIT EVEN PATH BLUE DATA BIT EVEN PATH BLUE DATA BIT EVEN PATH BLUE DATA BIT GROUND
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
OR0 OR1 OR2 OR3 OR4 OR5 GND OG0 OG1 OG2 OG3 OG4 OG5 GND OB0 OB1 OB2 OB3 OB4 OB5 GND GND
ODD PATH RED DATA BIT ODD PATH RED DATA BIT ODD PATH RED DATA BIT ODD PATH RED DATA BIT ODD PATH RED DATA BIT ODD PATH RED DATA BIT GROUND ODD PATH GREEN DATA BIT ODD PATH GREEN DATA BIT ODD PATH GREEN DATA BIT ODD PATH GREEN DATA BIT ODD PATH GREEN DATA BIT ODD PATH GREEN DATA BIT GROUND ODD PATH BLUE DATA BIT ODD PATH BLUE DATA BIT ODD PATH BLUE DATA BIT ODD PATH BLUE DATA BIT ODD PATH BLUE DATA BIT ODD PATH BLUE DATA BIT GROUND GROUND
Pin No. 1 2 3 4 5 6
Description Brightness Adjustment Inverter enable Ground Ground Input source Input source
36
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Symbol NC AUTO_ADJ NC EXIT MENU GND UP LED OR LED GR POWER_KEY NC HP_Detector DOWN NC AUDIO/RAUDIO/R+ AUDIO/LAUDIO/L+
Description AUTO ADJUSTMENT EXIT KEY MENU KEY GROUND UP KEY ORANGE LED GREEN LED POWER KEY HEADPHONE DETECT DOWN KEY AUDIO OUTPUT AUDIO OUTPUT AUDIO OUTPUT AUDIO OUTPUT
37
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Symbol GRAI GGAI GBAI NC GND RGND GGND BGND VGA_5V GND_ANA NC DSUB-SDA G_HSYNC G_VSYNC DSUB_SCL
Description RED INPUT GREEN INPUT BLUE INPUT GROUND RED INPUT GROUND GREEN INPUT GROUND BLUE INPUT GROUND VGA INPUT 5V GROUND I2C H-SYNC V-SYNC I2C
38
Chapter 6
35A15K0218
2714000001
35A15S0236
CABLES
AUDIO CABLE
28AWG,180 cm
32F2818001
39
MONITOR CABLE
427C,30AWG,180cm
32F3018001
STAND BASE
Seat Assy,
40A15929D3
Bezel Assy
40A1529947
Rear Assy
40A15929C4
40A15929D5
41A1599115
LCD BRACKET
40
Explosion Diagram
1.BEZEL_W/_SPEAKER_ASSY 2.OSD PCBA 3.SCREW 4.PANEL ASSY 5.PET_FILM_METAL_FRAM_R EAR 6.INVERTER 7.SMART PCBA 8.FFC AD_OSD 9.SCREW 10.PET ISOLUTION FILM 11.METAL COVER SMART 12.STAND-OFF 13.REAR_ASSY 14.SCREW 15.SEAT_ASSY 16.STAND_ASSY 17.SCREW 18.STAND HINGE_COVER
41
Chapter 7
Schematic Diagram
Main Board
42
43
44
45
46
47
48
49
50