Académique Documents
Professionnel Documents
Culture Documents
GT-550E
CARRIER : TC-4255
GENERAL DATA
CRANE CAPACITY
BOOM
DIMENSION
Overall length
Overall width
Overall height
MASS
Gross vehicle mass
-front axle
-rear axle
PERFORMANCE
Max. travelling speed
Gradeability (tan )
55,000 kg at 3.0 m
5-section, 11.1 m - 42.0m
approx.
approx.
approx.
13,480 mm
2,820 mm
3,680 mm
approx.
approx.
approx.
39,800 kg
15,900 kg
23,900 kg
computed
computed
83 km/h
53 %
CRANE SPECIFICATIONS
MODEL
GT-550E
CAPACITY
55,000 kg at 3.0 m
BOOM
JIB
ELEVATION
HOIST-Main winch
CRANE SPECIFICATIONS
HOIST-Auxiliary winch
SWING
HYDRAULIC SYSTEM
OUTRIGGER
FRONT JACK
COUNTERWEIGHT
-2-
CARRIER SPECIFICATIONS
MANUFACTURER
STEERING
MODEL
BRAKE SYSTEM
TADANO LTD.
ENGINE [ EURO-2 ]
Model.......................... NISSAN PF6
Type............................ 4 cycle, 6 cylinder in line, direct
injection, water cooled diesel
engine with turbochager.
Piston displacement... 12,503 cm3
Bore x stroke.............. 133 mm x 150 mm
Max. output (JIS)........ 257 kW{350PS/345hp}
at 2100 min-1{rpm}
Max. torque (JIS)........ 1460 Nm{150 kgfm}
at 1200 min-1{rpm}
TIRES
TRANSMISSION
CAB
AXLES
ELECTRIC SYSTEM
SUSPENSION
EQUIPMENT
FOR CRANE
Standard Equipment
Optional Equipment
FOR CARRIER
Standard Equipment
-3-
WORKING RANGE
25
Telescoping mode
45
BOOM
65
60
Approx.
2.5m
55
42.
0m
80
BO
OM
BO
OM
70
42.
0m
34.
3
2 6.
6m
18
.8
BO
OM 60
BO
JI B
40
35
OM
40
30
25
BO
OM
30
20
BO
15
20
OM
OM
BO
10
10
5
0
10
15
20
25
RADIUS (m)
30
JIB
45
JIB
50
11
.1
.0
m
50
M
O
15
.0
+9
+1
4.6
35
NOTE:
1. Boom and jib geometry shown are for unloaded
condition and machine standing level on firm
supporting surface.
Boom deflection and subsequent radius and boom
angle change must be accounted for when applying
load to hook.
2. When the boom length is 11.1 - 12.0 m, Max boom
angle is 76
40
42.0 m
34.3 m
26.6 m
18.8 m
15.0 m
11.1 m
-4-
42.
0m
Approx.
2.2m
0.8m
Approx.
2.3m
WORKING RANGE
25
Telescoping mode
45
BOOM
65
60
Approx.
2.5m
55
42.
0m
80
BO
OM
BO
OM
70
42.
0m
38.
1
34.
3
2 6.
6m
18
.8
.0
m
BO
OM 60
BO
BO
+9
50
+1
4.6
JI B
40
50
OM
35
OM
40
30
25
BO
OM
30
20
BO
M
O
15
20
11
.1
m
10
OM
BO
10
5
0
10
15
20
25
RADIUS (m)
30
JIB
45
JIB
35
NOTE:
1. Boom and jib geometry shown are for unloaded
condition and machine standing level on firm
supporting surface.
Boom deflection and subsequent radius and boom
angle change must be accounted for when applying
load to hook.
2. When the boom length is 11.1 - 12.0 m, Max boom
angle is 76
40
42.0 m
38.1 m
34.3 m
26.6 m
18.8 m
11.1 m
-5-
42.
0m
Approx.
2.2m
0.8m
Approx.
2.3m
ISO 4305
11.1 m
boom
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
9.0
10.0
11.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
30.0
32.0
34.0
55,000
43,700
38,500
34,200
30,800
27,800
25,400
23,200
21,400
19,700
18,300
15,200
15.0 m
boom
40,000
40,000
38,100
33,800
30,400
27,400
25,000
22,800
21,000
19,300
17,900
14,600
11,600
9,500
7,800
18.8 m boom
28,000
28,000
28,000
28,000
28,000
27,200
24,700
22,500
20,700
19,100
17,600
14,200
11,300
9,100
7,500
5,100
3,500
20,000
20,000
20,000
19,800
19,000
18,200
17,500
16,800
16,200
15,700
15,200
14,300
13,500
11,400
9,600
7,200
5,500
26.6 m boom
20,000
20,000
20,000
20,000
18,900
17,800
16,700
15,800
14,200
12,500
10,300
8,600
6,200
4,500
3,300
2,400
1,700
1,200
14,000
14,000
13,600
12,800
12,000
11,400
10,800
10,200
9,300
8,500
7,800
7,200
6,200
5,400
4,700
3,700
3,000
2,400
34.3 m boom
14,000
14,000
13,500
13,000
12,500
11,300
10,400
9,600
8,800
6,800
5,100
3,900
3,000
2,200
1,600
1,200
800
500
8,000
8,000
8,000
8,000
8,000
7,600
7,000
6,400
5,800
4,900
4,200
3,600
3,200
2,800
2,500
2,100
1,700
1,400
1,100
38.1 m
boom
42.0 m
boom
8,000
8,000
8,000
8,000
7,500
6,900
6,400
5,500
4,700
4,100
3,600
2,800
2,200
1,800
1,400
1,000
700
500
8,000
8,000
8,000
8,000
8,000
7,500
6,900
5,900
5,200
4,200
3,200
2,500
1,900
1,400
1,000
700
450
Telescoping conditions(%)
Telescoping
Mode
2nd boom
3rd boom
4th boom
Top boom
,
0
0
0
0
,
50
0
0
0
100
0
0
0
0
33
33
33
100
33
33
33
0
66
66
66
100
66
66
66
0
100
100
100
50
100
100
100
100
100
100
100
NOTES :
1. Rated lifting capacities shown in the table are based on the condition that the crane is set on firm ground horizontally. Those above
bold line are based on crane strength and those below, it is stability.
2. Rated lifting capacities in the stability area comply with part 2 / ISO 4305.
3. The mass of load handling devices such as hook blocks {570 kg for *55 ton capacity, 410 kg for *35 ton capacity, 400 kg for *20 ton
capacity and 130 kg for 4.5 ton capacity} and slings, shall be considered part of the load and must be deducted from rated lifting
capacities.
4. Without front jack extended, when the boom is within the Over-front, Rated lifting capacities are different from those for the boom in the
Over-side and Over-rear.
5. Standard number of parts of line for each boom length is as shown below. Load per-line should not surpass 42.2 kN {4,300 kgf} for
main winch rope and 44.1 kN {4,500 kgf} for auxiliary winch rope.
*: Optional
Boom Length
11.1 m
15.0 m
18.8 m
26.6 m
34.3 m
38.1 m
42.0 m
Jib/Single top
Number of parts of line
**13/12
10
7
5
4
4
4
1
**: With single top (When the lifting capacities is 55,000 kg)
6. Special weather caution: Refer to the operation and maintenance manual.
7. For rated lifting capacity of single top, subtract the main hook mass from the relevant boom rated lifting capacity. Rated lifting capacity
of single top should not exceed 4,500 kg.
8. Load radius shown in the table includes the deflection of the boom. Therefore, perform it according to the load radius. However for the
jib operation, perform it according to the boom angle regardless of the boom length. The load radius shows reference value when the
jib is attached to the 42.0 m boom, 38.1 m boom (Telescoping mode ) and 34.3 m boom (Telescoping mode ).
-6-
ISO 4305
11.1 m
boom
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
9.0
10.0
11.0
12.0
14.0
16.0
18.0
32,000
32,000
32,000
26,300
20,200
15,800
12,800
10,600
8,900
7,500
6,400
4,700
15.0 m
boom
28,000
28,000
28,000
25,500
19,200
15,100
12,200
10,000
8,300
7,000
5,900
4,200
3,000
2,100
1,300
18.8 m boom
28,000
28,000
28,000
24,900
18,700
14,600
11,800
9,600
8,000
6,600
5,500
3,900
2,700
1,800
1,000
20,000
20,000
20,000
19,700
18,900
17,700
14,600
12,300
10,500
9,100
7,900
6,100
4,800
3,800
3,000
1,900
1,100
26.6 m boom
20,000
20,000
16,400
13,300
11,100
9,400
8,000
6,800
5,100
3,800
2,900
2,100
1,000
14,000
14,000
13,500
12,700
12,000
11,100
9,700
8,500
6,700
5,300
4,300
3,500
2,300
1,500
34.3 m boom
14,000
11,900
10,100
8,700
7,500
5,800
4,500
3,500
2,700
1,600
8,000
8,000
8,000
8,000
8,000
7,100
5,600
4,600
3,800
2,600
1,800
1,200
38.1 m
boom
42.0 m
boom
8,000
8,000
8,000
6,500
5,200
4,200
3,400
2,200
1,400
8,000
8,000
7,900
6,100
4,800
3,800
3,000
1,900
1,000
Telescoping conditions(%)
Telescoping
Mode
2nd boom
3rd boom
4th boom
Top boom
,
0
0
0
0
,
50
0
0
0
100
0
0
0
0
33
33
33
100
33
33
33
0
66
66
66
11.1 m
boom
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
9.0
10.0
11.0
12.0
22,800
16,900
13,100
10,400
8,400
6,900
5,700
4,800
4,000
3,300
2,700
1,800
15.0 m
boom
22,100
16,300
12,500
9,900
7,900
6,500
5,300
4,300
3,500
2,900
2,300
1,400
18.8 m boom
21,700
15,900
12,100
9,500
7,600
6,100
5,000
4,000
3,200
2,600
2,000
1,100
20,000
18,600
14,600
11,900
9,800
8,300
7,000
6,000
5,200
4,500
3,900
2,900
2,200
1,600
1,100
26.6 m boom
11,800
8,800
7,300
6,100
5,100
4,300
3,600
3,000
2,100
1,400
12,500
10,400
8,800
7,600
6,500
5,700
5,000
4,400
3,400
2,700
2,100
1,600
100
33
33
33
0
66
66
66
Telescoping conditions(%)
Telescoping
Mode
2nd boom
3rd boom
4th boom
Top boom
,
0
0
0
0
50
0
0
0
100
0
0
0
0
33
33
33
-7-
100
66
66
66
0
100
100
100
50
100
100
100
100
100
100
100
ISO 4305
5offset
3,500
3,500
3,500
3,400
3,250
3,100
2,840
2,430
2,200
1,950
1,780
1,350
1,050
680
470
9.0 m jib
25offset
2,300
2,300
2,300
2,300
2,240
2,160
2,020
1,850
1,730
1,580
1,450
1,180
920
590
410
42.0 m boom
45offset
1,300
1,300
1,300
1,280
1,260
1,240
1,200
1,150
1,120
1,070
1,030
1,000
850
550
5offset
2,500
2,500
2,500
2,350
2,220
2,100
1,890
1,640
1,500
1,330
1,220
1,080
800
500
14.6 m jib
25offset
1,200
1,200
1,200
1,170
1,140
1,120
1,070
1,000
950
910
850
800
750
480
45offset
700
700
700
690
680
670
650
630
620
590
580
570
560
420
-8-
ISO 4305
5offset
3,500
3,500
3,080
2,550
2,090
1,700
1,070
9.0 m jib
25offset
2,300
2,300
2,280
1,910
1,580
1,300
42.0 m boom
45offset
1,300
1,300
1,300
1,280
1,260
1,070
5offset
2,500
2,500
2,500
2,190
1,800
1,470
14.6 m jib
25offset
1,200
1,200
1,200
1,170
1,140
1,010
45offset
700
700
700
690
680
670
5offset
3,500
3,500
3,500
3,400
2,910
2,480
1,780
1,010
5offset
3,500
3,500
3,500
3,400
2,910
2,480
1,780
1,010
-9-
WORKING AREA
1. Applicable rated lifting capacities change as the ranges of the working area, depending on the outrigger extension width and whether
the front jack is used.
2. When the swing automatic stop cancel switch is canceled, the swing does not automatically stop even if the crane becomes
overloaded.
N
M
Front
A
A:
B:
C:
D:
E:
Traveling direction
K
F :
G:
E
F
Left
Right
H
I
J
K
L
Rear
L
:
:
:
:
:
M:
N:
Over-front area
Over-rear area
Over-side area (right)
Over-side area (left)
Rated lifting capacity (capacity with outriggers at
minimum extension)
Rated lifting capacity (capacity with outriggers at middle
extension)
Rated lifting capacity (capacity with outriggers at full
extension)
Minimum extension width of outriggers
Middle extension width of outriggers
Full extension width of outriggers
Position of outrigger jack with the beam not extended
Position of outrigger jack with the beam extended
halfway
Position of outrigger jack with the beam extended fully
Front jack
H
I
Reference
Front jack extended
FL outrigger extended to fully, FR outrigger extended to fully
RL outrigger extended to middle, RR outrigger extended to fully
-10-
DIMENSION
65
IN
MIN
2,390
2,720
2,820
I
TA
SW
,
R3
290
40
MAX
6,800
MID
4,600
REAR AXLE
CENTER
5,480
14
12
1,240
2,650
3,680
OFFSET 800
2,240
4,540
1,470
2,580
3,930
10,915 (CARRIER)
13,480
-11-
2,900
1400
1,690
2,140
(International Division)
4-12, Kamezawa 2-chome,Sumida-ku, Tokyo 130-0014, Japan
Tel:81-3-3621-7750 Fax:81-3-3621-7785
http://www.tadano.co.jp/indexe.htm E-mail:tdnihq@tadano.co.jp