Académique Documents
Professionnel Documents
Culture Documents
PART-A (Marks:40)
1. Draw three views of a Hexagonal headed bolt of nominal diameter 25mm and length
100mm with a hexagonal nut and washer in place.
2. Draw the sectional front view and top view of a single riveted double strap butt
joint for a plate thickness of 12mm.
3. Draw a 2-d sectional profile of NACA 2410 from the data given below. Take airfoil
chord of 25cms for your workout.
N ACA 2410
(Stations and ordinates given in percent of airf oil chord)
Lower Surface
Upper Surface
Station Ordinate Station Ordinate
0
0
0
0
-1.448
1.402
1.694
1.098
-1.927
2.703
2.411
2.297
-2.482
5.258
3.420
4.742
-2.809
7.783
4.169
7.217
-3.016
10.290
4.766
9.710
-3.227
15.278
5.665
14.722
-3.276
20.239
6.276
19.761
-3.230
25.186
6.668
24.814
-3.125
30.125
6.875
29.875
-2.837
40.000
6.837
40.000
-2.468
49.951
6.356
50.049
-2.024
59.915
5.580
60.085
-1.551
69.898
4.551
70.102
-1.074
79.903
3.296
80.097
-0.594
89.933
1.816
90.067
-0.352
94.959
0.990
95.067
-0.150
100.000
0.105
100.000
L.E radius: 1.10
Stope of radius through L.E: 0.1
1 of 2
Set No. 1
Figure 4b
2 of 2
Set No. 2
PART-A (Marks:40)
1. Draw a Single Gib Head key for a shaft of 50mm size (assembly).
2. Draw the top view and sectional front view of a Single riveted lap joint. Take the
thickness of plate as 12mm.
3. Draw a 2-d sectional profile of NACA 2410 from the data given below. Take airfoil
chord of 25cms for your workout.
N ACA 2410
(Stations and ordinates given in percent of airf oil chord)
Lower Surface
Upper Surface
Station Ordinate Station Ordinate
0
0
0
0
-1.448
1.402
1.694
1.098
-1.927
2.703
2.411
2.297
-2.482
5.258
3.420
4.742
-2.809
7.783
4.169
7.217
-3.016
10.290
4.766
9.710
-3.227
15.278
5.665
14.722
-3.276
20.239
6.276
19.761
-3.230
25.186
6.668
24.814
-3.125
30.125
6.875
29.875
-2.837
40.000
6.837
40.000
-2.468
49.951
6.356
50.049
-2.024
59.915
5.580
60.085
-1.551
69.898
4.551
70.102
-1.074
79.903
3.296
80.097
-0.594
89.933
1.816
90.067
-0.352
94.959
0.990
95.067
-0.150
100.000
0.105
100.000
L.E radius: 1.10
Stope of radius through L.E: 0.1
Set No. 2
4. Figure 4b. gives the part drawings of foot step bearing. Assemble all the parts and
draw the following assembled views.
(a) Sectional front view
(b) Top view.
Figure 4b
2 of 2
Set No. 3
PART-A (Marks:40)
Upper surface
0
2.67
3.61
4.91
5.80
6.43
7.19
7.50
7.60
7.55
7.14
6.41
5.47
4.36
3.08
1.68
0.92
0
Lower surface
0
-1.23
-1.71
-2.26
-2.61
-2.92
-3.50
-3.97
-4.28
-4.46
-4.48
-4.17
-3.67
-3.00
-2.16
-1.23
-0.70
0
Set No. 3
4. Figure 4c. shows the isometric view of Structural wall bracket. Draw
(a) Sectional front view
(b) Top view.
(c) End view
Figure 4c
2 of 2
Set No. 4
PART-A (Marks:40)
1. Draw a Single Gib Head key for a shaft of 50mm size (assembly).
2. Draw the sectional front view and top view of a single riveted single cover butt
joint for a plate thickness of 12mm.
3. Draw a 2-d sectional profile of NACA 2415 from the data given below. Take airfoil
chord of 25cms for your workout.
N ACA 2415
(Stations and ordinates given in percent of airf oil chord)
Lower surface
Upper surface
Station Ordinate Station Ordinate
0
0
........
0
-2.06
1.25
2.71
1.25
-2.86
2.5
3.71
2.5
-3.84
5.0
5.07
5.0
-4.47
7.5
6.06
7.5
-4.90
10
6.83
10
-5.42
15
7.97
15
-5.66
20
8.70
20
-5.70
25
9.17
25
-5.62
30
9.38
30
-5.25
40
9.25
40
-4.67
50
8.57
50
-3.90
60
7.50
60
-3.05
70
6.10
70
-2.15
80
4.41
80
-1.17
90
2.45
90
-0.68
95
1.34
95
(-0.16)
100
(0.16)
100
0
100
.........
100
L.E.radius:2.48
Slope of radius through L.E.:0.10
Set No. 4
4. Figure 4. Given details of a Knuckle joint, draw top and front sectional views.
Figure 4
2 of 2